ISL9204 ® Data Sheet October 4, 2005 FN9207.0 High Input Voltage Charger Features The ISL9204 is a cost-effective, fully integrated high input voltage single-cell Li-ion battery charger. This charger performs the CC/CV charge function required by Li-ion batteries. The charger accepts an input voltage up to 28V but is disabled when the input voltage exceeds the OVP threshold, minimum 10V, to prevent excessive power dissipation. The 28V rating eliminates the overvoltage protection circuit required in a low input voltage charger. • Complete Charger for Single-Cell Li-ion/Polymer Batteries The charge current and the end-of-charge (EOC) current are programmable with external resistors. When the battery voltage is lower than a typical value of 2.8V, the charger preconditions the battery with typically 17% of the programmed charge current. When the charge current reduces to the programmable EOC current level during the CV charge phase, an EOC indication is provided by the CHG pin, which is an open-drain output. An internal thermal foldback function protects the charger from any thermal failure. • Programmable End-of-Charge Current Two indication pins (PPR and CHG) allow simple interface to a microprocessor or LEDs. When no adapter is attached or when disabled, the charger draws less than 1µA leakage current from the battery. • Ambient Temperature Range: -40°C to 85°C Ordering Information Applications PART NUMBER PART TEMP. MARKING RANGE (°C) ISL9204IRZ-T 04Z (Note) -40 to 85 PACKAGE PKG. DWG. # 8 Ld 2x3 DFN L8.2x3 Tape and Reel (Pb-free) Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 • Integrated Pass Element and Current Sensor • No External Blocking Diode Required • Low Component Count and Cost • 1% Voltage Accuracy • Programmable Charge Current • Charge Current Thermal Foldback for Thermal Protection • Trickle Charge for Fully Discharged Batteries • 28V Maximum Voltage for the Power Input • Power Presence and Charge Indications • Less than 1µA Leakage Current Off the Battery when No Input Power Attached or Charger Disabled • 2x3 DFN 8 Ld Packages • Pb-Free Plus Anneal Available (RoHS Compliant) • Mobile Phones • Blue-Tooth Devices • PDAs • MP3 Players • Stand-alone Chargers • Other Handheld Devices Pinout ISL9204 (8 LD 2x3 DFN) TOP VIEW VIN 1 8 BAT PPR 2 7 IREF CHG 3 6 IMIN EN 4 5 GND CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL9204 Absolute Maximum Ratings (Reference to GND) Thermal Information VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 30V Thermal Resistance (Typical, Notes 1, 2) θJA (°C/W) θJC (°C/W) DFN Package. . . . . . . . . . . . . . . . . . . . 59 4.5 Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C (SOIC, PLCC, etc. Lead Tips Only) IMIN, IREF, BAT, CHG, EN, PPR. . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V Recommended Operating Conditions Ambient Temperature Range . . . . . . . . . . . . . . . . . . . .-40°C to 85°C Maximum Supply Voltage (VIN Pin). . . . . . . . . . . . . . . . . . . . . . 28V Operating Supply Voltage (VIN Pin). . . . . . . . . . . . . . . . 4.3V to 10V Programmed Charge Current . . . . . . . . . . . . . . . . . 50mA to 350mA CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 2. For theta θJC the "case temp." location is the center of the exposed metal pad on the package underside. Electrical Specifications Typical Values Are Tested at VIN = 5V and the Ambient Temperature at 25°C. All Maximum and Minimum Values Are Guaranteed Under the Recommended Operating Supply Voltage Range and Ambient Temperature Range, Unless Otherwise Noted. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 3.3 3.9 4.3 V 3.1 3.6 4.15 V - 90 150 mV 10 50 - mV 10 10.5 13 V 200 400 500 mV Charger disabled or the input is floating - - 1.0 µA POWER-ON RESET Rising POR Threshold VPOR Falling POR Threshold VPOR VBAT = 3.0V, use PPR to indicate the comparator output. VIN-BAT OFFSET VOLTAGE Rising Edge VOS Falling Edge VOS VBAT = 4.0V, use CHG pin to indicate the comparator output (Note 3) OVER VOLTAGE PROTECTION Over Voltage Protection Threshold VOVP OVP Threshold Hysteresis Use PPR to indicate the comparator output (Note 4) STANDBY CURRENT BAT Pin Sink Current ISTANDBY VIN Pin Supply Current IVIN Charger disabled - 300 400 µA VIN Pin Supply Current IVIN Charger enabled - 500 700 µA VCH 4.3V < VIN < 10V Charge current = 20mA 4.158 4.20 4.242 V - 0.6 - Ω 1.165 1.210 1.245 V VOLTAGE REGULATION Output Voltage PMOS On Resistance rDS(ON) VBAT = 3.8V, charge current = 0.3A CHARGE CURRENT (Note 5) IREF Pin Output Voltage IIREF VBAT = 3.8V Constant Charge Current ICHG RIREF = 29.4kΩ, VBAT = 2.8V - 4.0V 135 150 165 mA Trickle Charge Current ITRK RIREF = 29.4kΩ, VBAT = 2.4V 18 25 32 mA End-of-Charge Current IMIN RIMIN = 137kΩ 20 30 40 mA RIREF = 29.4kΩ 90 110 130 mA EOC Rising Threshold PRECONDITIONING CHARGE THRESHOLD Preconditioning Charge Threshold Voltage VMIN 2.7 2.8 2.9 V Preconditioning Voltage Hysteresis VMINHYS 40 100 150 mV 2 FN9207.0 October 4, 2005 ISL9204 Electrical Specifications Typical Values Are Tested at VIN = 5V and the Ambient Temperature at 25°C. All Maximum and Minimum Values Are Guaranteed Under the Recommended Operating Supply Voltage Range and Ambient Temperature Range, Unless Otherwise Noted. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 100 115 130 °C EN Pin Logic Input High 1.3 - - V EN Pin Logic Input Low - - 0.5 V 100 200 400 kΩ 10 20 - mA - - 1 µA 10 20 - mA - - 1 µA INTERNAL TEMPERATURE MONITORING Charge Current Foldback Threshold (Note 6) TFOLD LOGIC INPUT AND OUTPUTS EN Pin Internal Pull Down Resistance CHG Sink Current When LOW Pin Voltage = 1V CHG Leakage Current When HIGH VCHG = 6.5V PPR Sink Current When LOW Pin Voltage = 1V PPR Leakage Current When HIGH VPPR = 6.5V NOTES: 3. The 4.0V VBAT is selected so that the CHG output can be used as the indication for the offset comparator output indication. If the VBAT is lower than the POR threshold, no output pin can be used for indication. 4. For junction temperature from -40°C to120°C. 5. The charge current can be affected by the thermal foldback function if the IC under the test setup cannot dissipate the heat. 6. Guaranteed by characterization or correlation to other test. Typical Characteristics 0.20 4.3 0.18 4.24 0.16 4.22 CONSTANT VOLTAGE 3.9 0.12 CONSTANT CURRENT 3.5 0.10 3.3 0.08 3.1 0.06 2.9 0.04 2.7 0.02 2.5 0 1K 2K 3K 4K 5K Ichg (A) 3.7 0.14 0.00 6K TIME (S) FIGURE 1. COMPLETE CHARGE CYCLE (130mAh BATTERY) 3 VBAT (V) 4.1 BAT VOLTAGE (V) 4.26 4.5 4.20 4.18 VIN = 5V TA = 25°C RIREF = 12.8K 4.16 4.14 4.12 4.10 0 50 100 150 200 250 300 350 IBAT (mA) FIGURE 2. CONSTANT VOLTAGE vs CHARGE CURRENT FN9207.0 October 4, 2005 ISL9204 160.0 1.6 152.5 1.4 145.0 1.2 137.5 1.0 VICDL (V) CHARGE CURRENT (mA) Typical Characteristics (Continued) 130.0 122.5 TA = 25°C RIREF = 29.4K VBAT = 3V 115.0 29.4K 0.6 VIN = 5V TA = 25°C VBAT = 3.9V 0.4 0.2 4 5 6 7 8 9 10 11 0.0 12 0 50 VIN (V) 150 200 250 300 FIGURE 4. VICDL vs CHARGE CURRENT 4.4 240 210 180 4.2 19.5K VIN = 5V TA = 25°C 4.0 VBAT (V) CHARGE CURRENT (mA) 100 CHARGE CURRENT (mA) FIGURE 3. CHARGE CURRENT vs VIN 150 29.4K 120 VIN = 5V TA = 25°C IBAT = 15mA 3.8 3.6 90 3.4 RIREF = 59K 60 3.2 30 0 3.0 0 1 2 3 VBAT (V) 4 5 3 4 5 6 7 8 9 10 11 VIN (V) FIGURE 6. VBAT vs VIN FIGURE 5. CHARGE CURRENT vs VBAT 4.25 152 4.24 148 4.23 144 4.22 140 VIN = 5V VB = 3.9V RIREF = 29.4K 136 VBAT (V) CHARGE CURRENT (mA) 19.5K 0.8 107.5 100.0 RIREF = 59K 132 4.20 4.19 VIN = 5V IBAT = 15mA 4.18 128 4.17 124 120 -40 4.21 4.16 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 7. CHARGE CURRENT vs TEMPERATURE 4 4.15 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 8. VBAT vs TEMPERATURE FN9207.0 October 4, 2005 ISL9204 Pin Descriptions current. The EOC current IMIN can be programmed by the following equation: VIN - Power input. The absolute maximum input voltage is 28V. A 0.47µF or larger value X5R ceramic capacitor is recommended to be placed very close to the input pin for decoupling purpose. Additional capacitance may be required to provide a stable input voltage. 4180 I MIN = ---------------R IMIN ( mA ) Where RIMIN is in kΩ. The programmable range covers 5% (or 10mA, whichever is higher) to 50% of IREF. When programmed to less than 5% or 10mA, the stability is not guaranteed. PPR - Open-drain power presence indication. The opendrain MOSFET turns on when the input voltage is above the POR threshold but below the OVP threshold and off otherwise. This pin is capable to sink 10mA (minimum) current to drive a LED. The maximum voltage rating for this pin is 7V. This pin is independent on the EN-pin input. IREF - Charge-current program and monitoring pin. Connect a resistor between this pin and the GND pin to set the charge current limit determined by the following equation: 4400 I REF = ----------------R IREF CHG - Open-drain charge indication pin. This pin outputs a logic LOW when a charge cycle starts and turns to HIGH when the end-of-charge (EOC) condition is qualified. This pin is capable to sink 10mA min. current to drive an LED. When the charger is disabled, the CHG outputs high impedance. ( mA ) Where RIREF is in kΩ. The IREF pin voltage also monitors the actual charge current during the entire charge cycle, including the trickle, constant-current, and constant-voltage phases. When disabled, VIREF = 0V. EN - Enable input. This is a logic input pin to disable or enable the charger. Drive to HIGH to disable the charger. When this pin is driven to LOW or left floating, the charger is enabled. This pin has an internal 200kΩ pull-down resistor. BAT - Charger output pin. Connect this pin to the battery. A 1µF or larger X5R ceramic capacitor is recommended for decoupling and stability purposes. When the EN pin is pulled to logic HIGH, the BAT output is disabled. GND - System ground. EPAD - Exposed pad. Connect as much as possible copper to this pad either on the component layer or other layers through thermal vias to enhance the thermal performance. IMIN - End-of-charge (EOC) current program pin. Connect a resistor between this pin and the GND pin to set the EOC Typical Application TO BATTERY TO INPUT BAT VIN RIREF C1 IREF IMIN RIMIN ISL9204 R1 R2 D1 D2 C2 CHG OFF PPR EN GND ON FIGURE 9. TYPICAL APPLICATION CIRCUIT INTERFACING TO INDICATION LEDS 5 FN9207.0 October 4, 2005 ISL9204 TABLE 1. COMPONENT DESCRIPTION FOR FIGURE 9 TABLE 2. COMPONENT DESCRIPTION FOR FIGURE 10 PART DESCRIPTION PART DESCRIPTION C1 1µF X5R ceramic cap C1 1µF X5R ceramic cap C2 1µF X5R ceramic cap C2 1µF X5R ceramic cap RIREF 29.4kΩ, 1%, for 150mA charge current RIREF 29.4kΩ, 1%, for 150mA charge current RIMIN 137kΩ, 1%, for 30mA EOC current RIMIN 137kΩ, 1%, for 30mA EOC current R1, R2 300Ω, 5% R1, R2 100kΩ, 5% D1, D2 LEDs for indication TO BATTERY TO INPUT BAT VIN RIREF C1 IREF C2 IMIN RIMIN ISL9204 OFF VCC EN ON R2 TO MCU R1 CHG GND PPR FIGURE 10. TYPICAL APPLICATION CIRCUIT WITH THE INDICATION SIGNALS INTERFACING TO A MCU VIN BAT VOS VREF BAT PRE REG POR VCC PPR VREF CHARGE CONTROL EN 200kΩ VCC EN DIE TEMP GND 115°C CHG IMIN IREF FIGURE 11. BLOCK DIAGRAM 6 FN9207.0 October 4, 2005 ISL9204 TRICKLE CC CV 4.2V CHARGE IREF VOLTAGE 73% IREF CHARGE CURRENT 3.0V IMIN 17% IREF CHG CHG INDICATION TIME FIGURE 12. TYPICAL CHARGE PROFILE Description The ISL9204 charges a Li-ion battery with a constant current (CC) or a constant voltage (CV). The constant current IREF is set with the external resistor RIREF (see Figure 9) and the constant voltage is fixed at 4.2V. If the battery voltage is below a typical 2.8V trickle-charge threshold, the ISL9204 charges the battery with a trickle current until the battery voltage rises above the trickle charge threshold. When the battery voltage reaches 4.2V, the charger enters a CV mode and regulates the battery voltage at 4.2V to fully charge the battery without the risk of over charge. Upon reaching an end-of-charge (EOC) current, the charger indicates the charge completion with the CHG pin, but the charger continues to output the 4.2V voltage. Figure 12 shows the typical charge profile and the EOC/reset event. higher than the POR threshold, the PPR pin turns on the internal open-drain MOSFET to indicate a logic LOW signal, independent on the EN-pin input. When the internal opendrain FET is turned off, the PPR pin should leak less than 1µA current. When turned on, the PPR pin should be able to sink at least 10mA current under all operating conditions. The PPR pin can be used to drive an LED (see Figure 9) or to interface with a microprocessor. Power-Good Range The power-good range is defined by the following three conditions: 1. VIN > VPOR 2. VIN - VBAT > VOS 3. VIN < VOVP The EOC current level IMIN is programmable with the external resistor RIMIN (see Figure 9). The CHG signal turns to LOW when the trickle charge starts and rises to HIGH at the EOC. After the EOC is reached, the charge current has to rise to typically 73% IREF for the CHG signal to turn on again, as shown in Figure 12. The current surge after EOC can be caused by a load connected to the battery. where the VOS is the offset voltage for the input and output voltage comparator, discussed shortly, and the VOVP is the overvoltage protection threshold given in the Electrical Specification. All VPOR, VOS, and VOVP have hysteresis, as given in the Electrical Specification table. The charger will not charge the battery if the input voltage is not in the power-good range. A thermal foldback function reduces the charge current anytime when the die temperature reaches typically 115°C. This function guarantees safe operation when the printedcircuit board (PCB) is not capable of dissipating the heat generated by the linear charger. The ISL9204 accepts an input voltage up to 28V but disables charging when the input voltage exceeds the OVP threshold, minimum 10V, to protect against unqualified or faulty AC adapters. Input and Output Comparator PPR Indication The PPR pin is an open-drain output to indicate the presence of the AC adapter. Whenever the input voltage is 7 The charger will not be enabled unless the input voltage is higher than the battery voltage by an offset voltage VOS. The purpose of this comparator is to ensure that the charger is turned off when the input power is removed from the charger. Without this comparator, it is possible that the charger will fail to power down when the input is removed and the current can leak through the PFET pass element to continue biasing the POR and the Pre-Regulator blocks shown in the Block Diagram. FN9207.0 October 4, 2005 ISL9204 Applications Information CHG Indication The CHG is an open-drain output capable to at least 10mA current when the charger starts to charge and turns off when the EOC current is reached. The CHG signal is interfaced either with a micro-processor GPIO or an LED for indication. EN Input EN is an active-low logic input to enable the charger. Drive the EN pin to LOW or leave it floating to enable the charger. This pin has a 200kΩ internal pulldown resistor so when left floating, the input is equivalent to logic LOW. Drive this pin to HIGH to disable the charger. The threshold for HIGH is given in the ES (Electrical Specification) table. IREF Pin The IREF pin has the two functions as described in the Pin Description section. When setting the fast charge current, the charge current is guaranteed to have 10% accuracy with the charge current set at 150mA. When monitoring the charge current, the accuracy of the IREF pin voltage vs. the actual charge current has the same accuracy as the gain from the IREF pin current to the actual charge current. The accuracy is 10% at 150mA and is expected to drop to 30% of the actual current (not the set constant charge current) when the current drops to 50mA. Operation Without the Battery The ISL9204 relies on a battery for stability and is not guaranteed to be stable if the battery is not connected. With a battery, the charger will be stable with an output ceramic decoupling capacitor in the range of 1µF to 200µF. The maximum load current is limited by the dropout voltage or the thermal foldback. Dropout Voltage The constant current may not be maintained due to the rDS(ON) limit at a low input voltage. The worst case on resistance of the pass FET is 1.2Ω the maximum operating temperature, thus if tested with 350mA current and 4.2V battery voltage, constant current could not be maintained when the input voltage is below 4.62V. Thermal Foldback The thermal foldback function starts to reduce the charge current when the internal temperature reaches a typical value of 115°C. 8 Input Capacitor Selection The input capacitor is required to suppress the power supply transient response during transitions. Mainly this capacitor is selected to avoid oscillation during the start up when the input supply is passing the POR threshold and the VIN-BAT comparator offset voltage. When the battery voltage is above the POR threshold, the VIN-VBAT offset voltage dominates the hysteresis value. Typically, a 1µF X5R ceramic capacitor should be sufficient to suppress the power supply noise. Output Capacitor Selection The criteria for selecting the output capacitor is to maintain the stability of the charger as well as to bypass any transient load current. The minimum capacitance is a 1µF X5R ceramic capacitor. The actual capacitance connected to the output is dependent on the actual application requirement. Charge Current Limit The actual charge current in the CC mode is limited by several factors in addition to the set IREF. Figure 13 shows three limits for the charge current in the CC mode. The charge current is limited by the on resistance of the pass element (power P-channel MOSFET) if the input and the output voltage are too close to each other. The solid curve shows a typical case when the battery voltage is 4.0V and the charge current is set to 350mA. The non-linearity on the RON-limited region is due to the increased resistance at higher die temperature. If the battery voltage increases to higher than 4.0V, the entire curve moves towards right side. As the input voltage increases, the charge current may be reduced due to the thermal foldback function. The limit caused by the thermal limit is dependent on the thermal impedance. As the thermal impedance increases, the thermal-limited curve moves towards left, as shown in Figure 13. Layout Guidance The ISL9204 uses a thermally-enhanced DFN package that has an exposed thermal pad at the bottom side of the package. The layout should connect as much as possible to copper on the exposed pad. Typically the component layer is more effective in dissipating heat. The thermal impedance can be further reduced by using other layers of copper connecting to the exposed pad through a thermal via array. Each thermal via is recommended to have 0.3mm diameter and 1mm distance from other thermal vias. FN9207.0 October 4, 2005 ISL9204 Input Power Sources The input power source is typically a well-regulated wall cube with 1-meter length wire or a USB port. The input voltage ranges from 4.3V to 10V. The ISL9204 can withstand up to 28V on the input without damaging the IC. If the input voltage is higher than the OVP threshold, the charger stops charging. THERMAL 350 LIMITED CHARGE CURRENT (mA) RON LIMITED RIREF INCREASES θJAOR TA INCREASES VBAT INCREASES \\ 4.0 4.5 5.0 5.5 10 INPUT VOLTAGE (V) FIGURE 13. CHARGE CURRENT LIMITS IN CONSTANT CURRENT MODE 9 FN9207.0 October 4, 2005 ISL9204 Dual Flat No-Lead Plastic Package (DFN) L8.2x3 2X 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE 0.15 C A A D 2X 0.15 C B E MILLIMETERS SYMBOL MIN A 0.80 A1 - 6 A3 INDEX AREA b TOP VIEW D2 // 0.10 A SIDE VIEW C SEATING PLANE D2 (DATUM B) C 0.08 C 0.20 A3 7 8 0.90 1.00 - - 0.05 - 0.25 0.32 1 5,8 1.50 1.65 1.75 7,8 3.00 BSC 1.65 e 1.80 1.90 7,8 0.50 BSC - k 0.20 - - - L 0.30 0.40 0.50 8 N 8 Nd 4 D2/2 6 INDEX AREA NOTES 2.00 BSC E E2 MAX 0.20 REF D B NOMINAL 2 3 Rev. 0 6/04 2 NX k NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd refers to the number of terminals on D. (DATUM A) E2 4. All dimensions are in millimeters. Angles are in degrees. E2/2 5. Dimension b applies to the metallized terminal and is measured between 0.25mm and 0.30mm from the terminal tip. NX L N N-1 NX b e 8 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 5 0.10 (Nd-1)Xe REF. M C A B 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. BOTTOM VIEW CL (A1) NX (b) L 5 SECTION "C-C" C C e TERMINAL TIP FOR EVEN TERMINAL/SIDE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 10 FN9207.0 October 4, 2005