Toggles Series HS TS PS GENERAL SPECIFICATIONS Rockers Electrical Capacity Pushbuttons Resistive Load: Other Ratings Materials & Finishes Knob: Shaft: Bushing: Case: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Installation Indicators Tilt G Touch Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Indexing: Contact Timing: Range of Operating Torque: Operating Temp Range: Humidity: Vibration: Shock: HS13: 6A @ 125V AC, 3A @ 250V AC, or 5A @ 30V DC HS16: 12A @ 125V AC or 6A @ 250V AC TS: 6A @ 125/250V AC PS: 30A @ 125/250V AC 10 milliohms maximum 200 megohms minimum @ 500V DC 1,500V AC minimum for 1 minute minimum HS: 15,000 operations minimum TS: 30,000 operations minimum PS: 10,000 operations minimum HS: 7,500 operations minimum TS: 10,000 operations minimum PS: 5,000 operations minimum 30° for HS16, TS & PS; 45° for HS13 Nonshorting HS13; Shorting & Nonshorting HS16; Nonshorting TS; Nonshorting PS HS16: 0.54 ~ 0.64Nm for first pole & 0.05Nm for each additional pole HS13: 0.15 ~ 0.24Nm TS: 0.09Nm for first pole & (0.07Nm x total number of poles) + 0.13Nm for additional poles PS: 0.14Nm for each pole Phenolic resin HS13: brass; HS16, TS, & PS: brass with nickel plating HS13: brass; HS16, TS, & PS: brass with nickel plating Phenolic resin HS13, HS16, & TS phosphor bronze; PS silver alloy HS13, HS16, & PS: brass with silver plating; TS: phosphor bronze HS: phosphor bronze; TS & PS: copper with silver plating –10°C through +70°C (+14°F through +158°F) 90 ~ 98% humidity for 96 hours @ 40°C (104°F) 10 ~ 55 Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 3 right angled directions, with 3 shocks in each direction) Mounting Torque: 2.94Nm (26 lb•in) Maximum Panel Thickness: Shown with panel cutouts in following drawings Soldering Time & Temperature: Manual Soldering (HS series only): See Profile A in Supplement section. Standards & Certifications UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. HS16 models 1– through 6–pole are recognized at 12A @ 125V AC & 6A @ 250V AC See Supplement section to find UL or cULus rating details. Supplement Accessories Standard Size Rotaries G46 www.nkk.com Toggles Series HS Standard Size Rotaries 6 AMP SINGLE POLE/NONSHORTING/45° INDEXING Stopper Settings Number of Terminals * Load Terminals HS13X HS13X-D 2 Fixed 1 COM, 2 LOAD 1&2 HS13Y HS13Y-D 3 Fixed 1 COM, 3 LOAD 1, 2, & 3 HS13Z HS13Z-D 4 Fixed 1 COM, 4 LOAD 1, 2, 3, & 4 Schematics HS13X CL of Keyway HS13Y 2 HS13Z CL of Keyway 3 2 CL of Keyway 3 4 2 1 1 1 C1 C1 C1 Rockers Number of Positions Pushbuttons D-flat Shaft Switch is viewed from shaft end and shown in position 1. Terminal numbers are not on switch. Standard Hardware shown on last page of this section. * Wire harness & cable assemblies offered only in Americas. 45° T yp 4 (6.0) Dia .236 2 (5.7) Typ .224 (0.3) .012 (10.0) (10.0) (16.0) .394 .394 .630 (40.0) 1.575 (34.0) Dia 1.339 (9.5) .374 (9.0) .354 1 (4.8) Typ .189 (10.3) Dia .406 (10.5) Dia .413 3 (1.5) .059 (3.0) Dia .118 Maximum Effective Panel Thickness With Locking Ring .150” (3.8mm) Without Locking Ring .189” (4.8mm) COM (2.6) Dia Typ .102 Programmable Illuminated PB (0.7) Typ .028 M10 P0.75 Keyway HS13X D-flat Shaft Shorting Nonshorting Shorting Pole Number of Positions Stopper Settings Number of Terminals * HS16-1 HS16-1S HS16-1N HS16-1SN 1P 2-11 2, 3, 4 . . . 11 1 COM, 11 LOAD Schematic HS16-2 HS16-2S HS16-2N HS16-2SN 2P 2-11 2, 3, 4 . . . 11 2 COM, 22 LOAD HS16-3 HS16-3S HS16-3N HS16-3SN 3P 2-11 2, 3, 4 . . . 11 3 COM, 33 LOAD HS16-4 HS16-4S HS16-4N HS16-4SN 4P 2-11 2, 3, 4 . . . 11 4 COM, 44 LOAD HS16-5 HS16-5S HS16-5N HS16-5SN 5P 2-11 2, 3, 4 . . . 11 5 COM, 55 LOAD HS16-6 HS16-6S HS16-6N HS16-6SN 6P 2-11 2, 3, 4 . . . 11 6 COM, 66 LOAD C1 1 11 G 2 3 10 CL of Keyway 4 9 5 8 7 Slides Knurled Shaft Nonshorting Keylocks 12 AMP/SHORTING & NONSHORTING/30° INDEXING Rotaries Round Shaft 6 15° Tactiles Switch is viewed from shaft end and shown in position 1. Terminal numbers are not on switch. Standard Hardware shown on last page of this section. * Wire harness & cable assemblies offered only in Americas. 30 ° Keyway 1 3 4 9 6 (55.0) 2.165 (1.5) .059 Maximum Effective Panel Thickness With Locking Ring .189” (4.8mm) Without Locking Ring .228” (5.8mm) (14.0) .551 (44.5) 1.752 (0.84) Typ .033 (54.5) 2.146 (74.5) 2.933 (64.5) 2.539 (2.6) Dia Typ .102 (6.24) Typ .246 (7.0) Max .276 • On each deck of multipole devices common and load terminals are in the same positions as shown in the schematic above. Accessories (3.0) Dia .118 (9.5) .374 (15.0) .591 (34.5) 1.358 • Switch is viewed from the shaft end and shown in position 1. • Terminal numbers are on the switch bottom. Stopper positions are molded on the top of the switch. • Standard Hardware shown on last page of this section. www.nkk.com Supplement (9.0) .354 (10.3) Dia .406 Touch (24.5) .965 Indicators (10.0) .394 (8.0) Typ .315 7 (4.4) .173 (10.5) Dia .413 8 5 10 (65.0) 2.559 11 2 COM Tilt M10 P0.75 (6.0) Dia .236 HS16-2N G47 Toggles Series TS Standard Size Rotaries Rockers 6 AMP/NONSHORTING/ADJUSTABLE STOP/30° INDEXING Model Pole Number of Positions Stopper Settings Number of Terminals Shaft Type TS1N 1P 2-11 2, 3, 4 . . . 11 1 COM, 11 LOAD D Flat Schematic CL of Keyway C1 1 2 Pushbuttons 11 TS2N 2P 2-11 2, 3, 4 . . . 11 2 COM, 22 LOAD D Flat 10 3 9 4 5 TS3N 3P 2-11 2, 3, 4 . . . 11 3 COM, 33 LOAD D Flat TS4N 4P 2-11 2, 3, 4 . . . 11 4 COM, 44 LOAD D Flat TS5N 5P 2-11 2, 3, 4 . . . 11 5 COM, 55 LOAD D Flat 6 7 On each deck of multipole devices common & load terminals are in the same positions as shown in this schematic. Switch is viewed from the shaft end and shown in position 1. Terminal numbers are on the switch bottom. Stopper positions are molded on the top of the switch. • Standard Hardware shown on last page of this section. Top Panel Cutouts 15° Keyway 3 4 2 3 5 4 6 5 6 (42.0) Dia 1.654 (44.0) Dia 1.732 Touch M3 x 4 Typ Indicators M10 P0.75 Accessories Supplement (6.0) Dia .236 (13.0) .512 (15.6) .614 TS5N www.nkk.com 7 Slides 1 9 7 Maximum Effective Panel Thickness With Locking Ring .189” (4.8mm) Without Locking Ring .228” (5.8mm) G48 COM 10 (4.4) .173 8 Tactiles 1 2 9 (1.5) .059 (3.0) Dia .118 Tilt 15° 1 (9.5) .374 10 (9.0) .354 ° 30 (10.3) Dia .406 11 (10.5) Dia .413 Bottom 8 G 1 Rotaries Keylocks Programmable Illuminated PB 8 (22.0) .866 (14.0) .551 (34.0) 1.339 (46.0) 1.811 (58.0) 2.283 (70.0) 2.756 Toggles Series PS Standard Size Rotaries 30 AMP/NONSHORTING/ADJUSTABLE STOP/30° INDEXING Knurled Shaft D Flat Shaft Pole Number of Positions Stopper Settings Number of Terminals PS1 PS1N 1P 2-11 2, 3, 4 . . . 11 1 COM, 11 LOAD Rockers Schematic CL of Keyway C1 1 PS2 PS2N 2P 2-11 2, 3, 4 . . . 11 2 COM, 22 LOAD PS3 PS3N 3P 2-11 2, 3, 4 . . . 11 3 COM, 33 LOAD 10 3 PS4 PS4N 4P 2-11 2, 3, 4 . . . 11 4 COM, 44 LOAD 9 4 PS5 PS5N 5P 2-11 2, 3, 4 . . . 11 5 COM, 55 LOAD Pushbuttons 2 11 7 Programmable Illuminated PB 5 8 6 On each deck of multipole devices common & load terminals are in the same positions as shown in this schematic. Switch is viewed from the shaft end and shown in position 1. Terminal numbers are on switch bottom. Stopper positions are molded on the top of the switch. • Standard Hardware shown on last page of this section. Top Bottom (10.5) Dia .413 10 15° 11 COM 4 3 120°Typ G 1 6 2 10 (3.0) Dia .118 2 4 3 (40.0) Dia 1.575 Maximum Effective Panel Thickness Without Locking Ring .189” (4.8mm) Slides 11 5 M4 (76.0) Dia 2.992 Tactiles (20.0) R .787 8 (9.0) .354 7 ° Typ 120 7 9 8 6 30 ° Ty p (4.5) Dia Typ .177 Keylocks (4.4) .173 Rotaries Panel Cutout (70.0) Dia 2.756 Tilt M4 x 5 Typ M10 P0.75 Touch Keyway Indicators (6.0) Dia .236 (15.0) .591 (29.0) 1.142 (24.5) .965 (42.0) 1.654 (59.5) 2.343 (77.0) 3.031 (94.5) 3.720 (15.0) Max .591 www.nkk.com Supplement (7.0) .276 Accessories (10.0) .394 PS4N G49 Series HS TS PS Toggles Standard Size Rotaries SHAFT TYPES Rockers D Flat Shaft Dim A (6.0) Dia .236 (4.4) .173 Pushbuttons For use with AT431 and AT432 Knurled Shaft Dimension B For TS (15.6) .614 For HS (15.0) or PS .591 (6.0) Dia .236 Not for use with AT431 or AT432 (20.0) .787 Programmable Illuminated PB OPTIONAL KNOBS FOR D FLAT SHAFTS AT431 Large Knob AT432 Small Knob Phenolic Resin Phenolic Resin (19.5) .768 Black only with white indicator (24.0) line .945 Keylocks Rotaries Dim B Dimension A For TS (13.0) .512 For HS (10.0) or PS .394 (30.0) Dia 1.181 (15.6) .614 (21.0) .827 (25.0) Dia .984 (5.5) .217 (5.5) .217 (24.0) .945 (9.0) .354 G (57.0) 2.244 Black only with white indicator line Knob Orientation (29.0) 1.142 (21.0) .827 (9.0) .354 (21.0) .827 (28.0) 1.102 (20.0) .787 M2.3 x 0.4 x 8.0 Assembly Screw Set Screw Adaptor Shaft Slides M2.3 x 0.4 x 8.0 (41.0) 1.614 The rotary knobs used on the D-flat shafts can be oriented on the switch to suit the customer’s particular front panel needs simply by sliding the knob over the square adaptor at the preferred orientation. Tactiles AT526 The HS16, TS, and PS switches are supplied with the stopper plate set for the maximum number of positions allowed for that model. Prior to installation, the desired stopper setting should be made: AT518 AT526 2. Loosen the nut far enough to allow raising the stopper plate for resetting. 3. Insert the stopper in the numbered hole for the desired stopper setting. Satisfactory switch functioning cannot be assured if the stopper plate is not properly positioned. 6 7 Supplement AT526 Hex Mounting Nut (quantity 3) AT518 Locking Ring (quantity 1) AT520 Split Lockwasher (quantity 1) Use of mounting supports on PS is optional; screws are not provided. G50 www.nkk.com 5 4 3 11 Standard Hardware Supplied with HS, TS, and PS: 10 4. Tighten the nut firmly against the stopped plate. 2 Indicators AT526 1. Be sure the shaft is turned counterclockwise to the extreme left. If the shaft is not turned counterclockwise to the extreme left, proper setting cannot be achieved. 9 Accessories AT520 1 Touch For HS16, TS, & PS Models Tilt STOPPER SETTING