ISL6228 ® Data Sheet May 7, 2008 High-Performance Dual-Output Buck Controller for Notebook Applications Features The ISL6228 IC is a dual channel synchronous-buck PWM controller featuring Intersil's Robust Ripple Regulator (R3) technology that delivers truly superior dynamic response to input voltage and output load transients. Integrated MOSFET drivers and bootstrap diodes result in fewer components and smaller implementation area. • Fast transient response • High performance R3 technology Intersil’s R3 technology combines the best features of fixedfrequency and hysteretic PWMs while eliminating many of their shortcomings. R3 technology employs an innovative modulator that synthesizes an AC ripple voltage signal VR, analogous to the output inductor ripple current. The AC signal VR enters a window comparator where the lower threshold is the error amplifier output VCOMP, and the upper threshold is a programmable voltage reference VW, resulting in generation of the PWM signal. The voltage reference VW sets the steady-state PWM frequency. Both edges of the PWM can be modulated in response to input voltage transients and output load transients, much faster than conventional fixedfrequency PWM controllers. Unlike a conventional hysteretic converter, each channel of the ISL6228 has an error amplifier that provides ±1% voltage regulation at the FB pin. The ISL6228 has a 1.5ms digital soft-start and can be started into a pre-biased output voltage. A resistor divider is used to program the output voltage setpoint. The ISL6228 operates in continuous-conduction-mode (CCM) in heavy load, and in diode-emulation-mode (DEM) in light load to improve light-load efficiency. In CCM, the controller always operates as a synchronous rectifier. In DEM, the low-side MOSFET is permitted to stay off, blocking negative current flow into the low-side MOSFET from the output inductor. Pinout OCSET2 UGATE2 VO2 EN2 FB2 26 PHASE2 PGOOD2 27 25 24 23 22 VIN2 2 20 PVCC2 VCC2 3 19 LGATE2 VIN1 5 FSET1 6 PGOOD1 7 14 BOOT1 OCSET1 13 UGATE1 FB1 VO1 11 12 1 PHASE1 10 EN1 9 • Output voltage range: +0.6V to +5V • Diode emulation mode for increased light load efficiency • Programmable PWM frequency: 200kHz to 600kHz • Pre-biased output start-up capability • Integrated MOSFET drivers and bootstrap diode • Internal digital soft-start • Power good monitor • Fault protection - Undervoltage protection - Soft crowbar overvoltage protection - Inductor DCR overcurrent protection - Over-temperature protection - Fault identification by PGOOD pull-down resistance • Pb-free (RoHS compliant) Applications • General purpose switching buck regulators • PCI express graphical processing unit • Auxiliary power rail • VRM • Network adaptor TEMP (°C) PACKAGE (Pb-Free) PKG. DWG. # 6228HRTZ -10 to +100 28 Ld 4x4 TQFN L28.4x4A ISL6228HRTZ-T* 6228HRTZ -10 to +100 28 Ld 4x4 TQFN L28.4x4A Tape and Reel ISL6228IRTZ 6228IRTZ -40 to +100 28 Ld 4x4 TQFN L28.4x4A 18 PGND2 ISL6228IRTZ-T* 6228IRTZ -40 to +100 28 Ld 4x4 TQFN L28.4x4A Tape and Reel 17 PGND1 *Please refer to TB347 for details on reel specifications. 16 LGATE1 NOTE: These Intersil Pb-free plastic packaged products employ special Pbfree material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 15 PVCC1 8 • Wide input voltage range: +3.3V to +25V ISL6228HRTZ 21 BOOT2 GND • Individual power stage input rail for each channel PART NUMBER PART (Note) MARKING FSET2 1 VCC1 4 • ±1% regulation accuracy: -40°C to +100°C Ordering Information ISL6228 (28 LD 4x4 TQFN) 28 FN9095.2 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2007, 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners. Block Diagram VIN2 FB2 VCC1 VCC2 FB1 VIN1 VO1 VO2 PWM FREQUENCY CONTROL PWM FREQUENCY CONTROL − + VW 10µA gm − − PWM − − − EA − − − 10µA 10µA − +150° OT 60Ω 90Ω 30Ω 30Ω PHASE1 SHOOT THROUGH PROTECTION + OCP − DRIVER UGATE1 DRIVER DIGITAL SOFTSTART + UVP + UVP + OCP POR − SHOOT THROUGH PROTECTION BOOT1 + OVP + OVP PWM CONTROL PHASE2 EN1 + + DIGITAL SOFTSTART + LGATE1 DRIVER 90Ω 60Ω +150° OT PACKAGE BOTTOM FN9095.2 May 7, 2008 PVCC2 PGND2 PGOOD2 OCSET2 GND OCSET1 FIGURE 1. SCHEMATIC BLOCK DIAGRAM PGOOD1 PGND1 PVCC1 ISL6228 DRIVER VCOMP − − VREF VREF EA POR CR R Q S 100pF 100pF BOOT2 VR + PWM CONTROL CR − − + VCOMP + gm + gm VR EN2 LGATE2 + − PWM + UGATE2 + VW + gm − 2 R Q S 10µA − + + FSET1 − FSET2 ISL6228 Typical Application 5V RPGOOD2 RPVCC2 RVCC2 RVCC1 VCC2 VCC1 PVCC2 CPVCC2 RPGOOD1 RPVCC1 PVCC1 CVCC2 CVCC1 CPVCC1 PGOOD2 PGOOD1 PGOOD2 PGOOD1 VIN1 VIN2 VIN2 VIN1 3.3V TO 25V 3.3V TO 25V CIN2 UGATE1 UGATE2 BOOT2 BOOT1 CBOOT2 LO2 VO2 CIN1 QHIGH_SIDE1 QHIGH_SIDE2 CBOOT1 PHASE2 LO1 VO1 PHASE1 0.6V TO 5V CO2 0.6V TO 5V CSEN2 ISL6228 QLOW_SIDE2 QLOW_SIDE1 ROCSET2 CFB2 PGND2 LGATE1 PGND1 OCSET2 OCSET1 VO2 RTOP2 VO1 RFB1 CFB1 FB1 FB2 FSET1 FSET2 RBOTTOM2 RTOP1 RO1 RO2 RFSET2 CO1 ROCSET1 LGATE2 RFB2 CSEN1 RBOTTOM1 CFSET1 CFSET2 RFSET1 EN1 EN2 GND 3 FN9095.2 May 7, 2008 ISL6228 Absolute Voltage Ratings Thermal Information VIN1,2 to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +28V VCC, PGOOD1,2 to GND . . . . . . . . . . . . . . . . . . . . . -0.3V to +7.0V PVCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7.0V EN1,2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to GND, VCC +3.3V VO1,2, FB1,2, FSET1,2 . . . . . . . . . . . . . . -0.3V to GND, VCC +0.3V PHASE1,2 to GND . . . . . . . . . . . . . . . . . . . . . . . (DC) -0.3V to +28V (<100ns Pulse Width, 10µJ) . . . . . . . . . . . . . . . . . . . . . . . . . -5.0V BOOT1,2 to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +33V BOOT1,2 to PHASE1,2 . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7V UGATE1,2 . . . . . . . . . . . . (DC) -0.3V to PHASE1,2, BOOT1,2 +0.3V (<200ns Pulse Width, 20µJ) . . . . . . . . . . . . . . . . . . . . . . . . -4.0V LGATE1,2 . . . . . . . . . . . . . . . . . . . (DC) -0.3V to GND, PVCC +0.3V (<100ns Pulse Width, 4µJ) . . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V Thermal Resistance (Typical, Notes 1, 2) θJA (°C/W) θJC (°C/W) TQFN Package . . . . . . . . . . . . . . . . . . 40 3 Junction Temperature Range. . . . . . . . . . . . . . . . . .-55°C to +150°C Operating Temperature Range . . . . . . . . . . . . . . . .-40°C to +100°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Ambient Temperature Range. . . . . . . . . . . . . . . . . .-10°C to +100°C Supply Voltage (VIN to GND) . . . . . . . . . . . . . . . . . . . . 3.3V to 25V VCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±5% PVCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±5% CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. 3. Limits established by characterization and are not production tested. Electrical Specifications These specifications apply for TA = -40°C to +100°C; All typical specifications TA = +25°C, VCC = 5V, PVCC = 5V; Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT - 16 - µA - 0.1 1.0 µA VIN VIN Input Bias Current IVIN EN = 5V, VIN = 15V IVIN_SHDN EN = GND, VIN = 25V VIN Shutdown Current VCC and PVCC VCC Input Bias Current in Single-Channel IVCC_S EN1 = 5V, FB1 = 0.65V, VIN1 = 3.3V to 25V, EN2 = GND, FB2 = GND, VIN2 = GND - 1 - VCC Input Bias Current in Dual Channel IVCC_D EN1 = 5V, FB1 = 0.65V, VIN1 = 3.3V to 25V, EN2 = 5V, FB2 = 0.65V, VIN2 = 3.3V to 25V - 2 - mA mA VCC Shutdown Current IVCC_SHDN EN1 = GND, EN2 = GND, VCC = 5V - 0.1 1.0 µA PVCC Shutdown Current IPVCC_SHDN EN1 = GND, EN2 = GND, PVCC = 5V - 0.1 1.0 µA 4.33 4.45 4.55 V VCC POR THRESHOLD Rising VCC POR Threshold Voltage VVCC_THR Falling VCC POR Threshold Voltage V TA = -10°C to +100°C VCC_THF TA = -10°C to +100°C 4.35 4.45 4.55 V 4.08 4.20 4.30 V 4.10 4.20 4.30 V REGULATION Reference Voltage VREF Regulation Accuracy Close loop - 0.6 - V -1 - +1 % 200 - 600 kHz -12 - +12 % 0.60 - 5 V PWM Frequency Range fSW fSW = 300kHz Frequency-Set Accuracy VO Range VVO VO Input Leakage IVO 4 EN = 5V, VO = 0.60V - 1 - µA EN = 5V, VO = 5V - 7.0 - µA EN = 0V, VO = 5V - 0.1 - µA FN9095.2 May 7, 2008 ISL6228 Electrical Specifications These specifications apply for TA = -40°C to +100°C; All typical specifications TA = +25°C, VCC = 5V, PVCC = 5V; Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT ERROR AMPLIFIER FB Input Bias Current FB = 0.60V -33 - 15 nA FB = 0.60V TA = -10°C to +100°C -35 - 15 nA RPG_SS PGOOD = 5mA Sink 70 95 125 Ω IFB POWER GOOD PGOOD Pull-Down Impedance PGOOD Leakage Current RPG_SS PGOOD = 5mA Sink TA = -10°C to +100°C 75 95 125 Ω RPG_UV PGOOD = 5mA Sink 70 95 125 Ω RPG_UV PGOOD = 5mA Sink TA = -10°C to +100°C 75 95 125 Ω RPG_OV PGOOD = 5mA Sink 45 63 85 Ω RPG_OV PGOOD = 5mA Sink TA = -10°C to +100°C 50 63 85 Ω RPG_OC PGOOD = 5mA Sink 22 32 45 Ω RPG_OC PGOOD = 5mA Sink TA = -10°C to +100°C 25 32 45 Ω IPGOOD PGOOD = 5V - 0.1 1.0 µA PGOOD Maximum Sink Current (Note 3) PGOOD Soft-Start Delay tSS EN High to PGOOD High - 5.0 - mA 2.20 2.75 3.50 ms 1.5 Ω GATE DRIVER UGATE Pull-Up Resistance (Note 3) RUGPU 200mA Source Current - 1.0 UGATE Source Current (Note 3) IUGSRC UGATE - PHASE = 2.5V - 2.0 - A UGATE Sink Resistance (Note 3) RUGPD 250mA Sink Current - 1.0 1.5 Ω UGATE Sink Current (Note 3) IUGSNK UGATE - PHASE = 2.5V - 2.0 - A LGATE Pull-Up Resistance (Note 3) RLGPU 250mA Source Current - 1.0 1.5 Ω LGATE Source Current (Note 3) ILGSRC LGATE - PGND = 2.5V - 2.0 - A LGATE Sink Resistance (Note 3) RLGPD 250mA Sink Current - 0.5 0.9 Ω LGATE Sink Current (Note 3) ILGSNK LGATE - PGND = 2.5V - 4.0 - A UGATE to LGATE Deadtime tUGFLGR UGATE falling to LGATE rising, no load - 21 - ns LGATE to UGATE Deadtime tLGFUGR LGATE falling to UGATE rising, no load - 21 - ns BOOTSTRAP DIODE Forward Voltage VF PVCC = 5V, IF = 2mA - 0.58 - V Reverse Leakage IR VR = 25V - 0.2 - µA 2.0 - - V - - 1.0 V - 0.1 1.0 µA CONTROL INPUTS EN High Threshold VENTHR EN Low Threshold VENTHF EN Leakage IENL EN = 0V IENH EN = 5.0V 1.4 2 2.5 µA EN = 5.0V TA = -10°C to +100°C 1.5 2 2.5 µA -1.75 0 1.75 mV PROTECTION OCSET-VO Threshold VOCSETTHR OCSET 10µA Current Source IOCSET EN = 5V 8.8 10 10.5 µA EN = 5V TA = -10°C to +100°C 9 10 10.5 µA EN = 0V - 0 - µA - 600 - kΩ OCSET 10µA Current Source Impedance ROCSETIMP EN = 5V, OCSET = 1.2V VUV 81 86 87 % OVP Rising Threshold VOVR 113 116 120 % OVP Falling Threshold VOVF 100 102 106 % UVP Threshold 5 FN9095.2 May 7, 2008 ISL6228 Electrical Specifications These specifications apply for TA = -40°C to +100°C; All typical specifications TA = +25°C, VCC = 5V, PVCC = 5V; Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) PARAMETER SYMBOL OTP Rising Threshold (Note 3) OTP Hysteresis (Note 3) MIN TYP MAX UNIT TOTR - 150 - °C TOTHYS - 25 - °C Functional Pin Descriptions GND (Bottom Pad) Signal common of the IC. Unless otherwise stated, signals are referenced to the GND pin. FSET2 (Pin 1) TEST CONDITIONS connected across the VO1, FB1, and GND pins. Select the resistor values such that FB1 to GND is 600mV when the converter output voltage is at the programmed regulation value. VO1 (Pin 9) The FSET2 pin programs the PWM switching frequency of Channel 2. Program the desired PWM frequency with a resistor and a capacitor connected across the FSET2 and GND pins. The VO1 pin measures the Channel 1 converter output voltage and is used as an input to the Channel 1 R3 PWM modulator. It also serves as part of Channel 1 inductor current sensing and the OCP overcurrent fault protection circuit. VIN2 (Pin 2) OCSET1 (Pin 10) The VIN2 pin measures the input voltage of the Channel 2 converter. It is a required input to the Channel 2 R3 PWM modulator. Connect the VIN2 pin to the drain of the Channel 2 high-side MOSFET. The OCSET1 pin measures the Channel 1 inductor current and programs the threshold of the OCP overcurrent fault protection. VCC2 (Pin 3) The EN1 pin is the on/off switch of Channel 1. The soft-start sequence begins when the EN1 pin is pulled above the rising threshold voltage VENTHR and VCC1 is above the power-on reset (POR) rising threshold voltage VVCC_THR . When the EN1 pin is pulled below the falling threshold voltage VENTHF PWM1 immediately stops. The VCC2 pin is the input bias voltage for Channel 2. Connect +5V to the VCC2 pin. Decouple with at least 1µF of a MLCC capacitor from the VCC2 pin to the GND pin. VCC1 (Pin 4) The VCC1 pin is the input bias voltage for Channel 1. Connect +5V to the VCC1 pin. Decouple with at least 1µF of a MLCC capacitor from the VCC1 pin to the GND pin. VIN1 (Pin 5) The VIN1 pin measures the input voltage of the Channel 1 converter. It is a required input to the Channel 1 R3 PWM modulator. Connect the VIN1 pin to the drain of the Channel 1 high-side MOSFET. FSET1 (Pin 6) The FSET1 pin programs the PWM switching frequency of Channel 1. Program the desired PWM frequency with a resistor and a capacitor connected across the FSET1 and GND pins. EN1 (Pin 11) PHASE1 (Pin 12) The PHASE1 pin is the current return path for the Channel 1 high-side MOSFET gate driver. Connect the PHASE1 pin to the node consisting of the high-side MOSFET source, the low-side MOSFET drain, and the output inductor of the Channel 1 converter. UGATE1 (Pin 13) The UGATE1 pin is the output of the Channel 1 high-side MOSFET gate driver. Connect the UGATE1 pin to the gate of the Channel 1 converter high-side MOSFET. BOOT1 (Pin 14) The PGOOD1 pin is an open-drain output that indicates when the Channel 1 converter is able to supply regulated voltage. Connect the PGOOD1 pin to +5V through a pull-up resistor. The BOOT1 pin stores the input voltage for the Channel 1 high-side MOSFET gate driver. Connect an MLCC capacitor across the BOOT1 and PHASE1 pins. The boot capacitor is charged through an internal boot diode connected from the PVCC1 pin to the BOOT1 pin, each time the PHASE1 pin drops below PVCC1 minus the voltage dropped across the internal boot diode. FB1 (Pin 8) PVCC1 (Pin 15) The FB1 pin is the inverting input of the control-loop error amplifier for Channel 1. The Channel 1 converter output voltage regulates to 600mV from the FB1 pin to the GND pin. Program the desired output voltage with a resistor network The PVCC1 pin is the input voltage bias for the Channel 1 low-side MOSFET gate drivers. Connect +5V to the PVCC1 PGOOD1 (Pin 7) 6 FN9095.2 May 7, 2008 ISL6228 pin. Decouple with at least 1µF of an MLCC capacitor across the PVCC1 and PGND1 pin. LGATE1 (Pin 16) The LGATE1 pin is the output of the Channel 1 converter low-side MOSFET gate driver. Connect the LGATE1 pin to the gate of the Channel 1 converter low-side MOSFET. PGND1 (Pin 17) The PGND1 pin is the current return path for the Channel 1 converter low-side MOSFET gate driver. Connect the PGND1 pin to the source of the Channel 1 converter lowside MOSFET through a low impedance path, preferably in parallel with the trace connecting the LGATE1 pin to the gate of the Channel 1 converter low-side MOSFET. PGND2 (Pin 18) The PGND2 pin is the current return path for the Channel 2 converter low-side MOSFET gate driver. Connect the PGND2 pin to the source of the Channel 2 converter lowside MOSFET through a low impedance path, preferably in parallel with the trace connecting the LGATE2 pin to the gate of the Channel 2 converter low-side MOSFET. LGATE2 (Pin 19) The LGATE2 pin is the output of the Channel 2 converter low-side MOSFET gate driver. Connect to the gate of the Channel 2 converter low-side MOSFET. PVCC2 (Pin 20) The PVCC2 pin is the input voltage bias for the Channel 2 low-side MOSFET gate drivers. Connect +5V to the PVCC2 pin. Decouple with at least 1µF of an MLCC capacitor across the PVCC2 and PGND2 pin. BOOT2 (Pin 21) The BOOT2 pin stores the input voltage for the Channel 2 high-side MOSFET gate driver. Connect an MLCC capacitor across the BOOT2 and PHASE2 pins. The boot capacitor is charged through an internal boot diode connected from the PVCC2 pin to the BOOT2 pin, each time the PHASE2 pin drops below PVCC2 minus the voltage dropped across the internal boot diode. UGATE2 (Pin 22) The UGATE2 pin is the output of the Channel 2 high-side MOSFET gate driver. Connect to the gate of the Channel 2 converter high-side MOSFET. PHASE2 (Pin 23) The PHASE2 pin is the current return path for the Channel 2 high-side MOSFET gate driver. Connect the PHASE2 pin to the node consisting of the high-side MOSFET source, the low-side MOSFET drain, and the output inductor of the Channel 2 converter. 7 EN2 (Pin 24) The EN2 pin is the on/off switch of Channel 2. The soft-start sequence begins when the EN2 pin is pulled above the rising threshold voltage VENTHR and VCC2 is above the power-on reset (POR) rising threshold voltage VVCC_THR . When the EN2 pin is pulled below the falling threshold voltage VENTHF, PWM2 immediately stops. OCSET2 (Pin 25) The OCSET2 pin measures the Channel 2 inductor current and programs the threshold of the OCP overcurrent fault protection. VO2 (Pin 26) The VO2 pin measures the Channel 2 converter output voltage and is used as an input to the Channel 2 R3 PWM modulator. It also serves as part of Channel 2 inductor current sensing and the OCP overcurrent fault protection circuit. FB2 (Pin 27) The FB2 pin is the inverting input of the control-loop error amplifier for Channel 2. The Channel 2 converter output voltage regulates to 600mV from the FB2 pin to the GND pin. Program the desired output voltage with a resistor network connected across the VO2, FB2, and GND pins. Select the resistor values such that FB2 to GND is 600mV when the converter output voltage is at the programmed regulation value. PGOOD2 (Pin 28) The PGOOD2 pin is an open-drain output that indicates when the Channel 2 converter is able to supply regulated voltage. Connect the PGOOD2 pin to +5V through a pull-up resistor. Theory of Operation Two Separate Channels The ISL6228 is a dual channel controller. Pins 4~17 are dedicated to Channel 1, and pins 1~3 and pins 18~28 are dedicated to Channel 2. The two channels are identical and almost entirely independent, with the exception of sharing the GND pin. Unless otherwise stated, only an individual channel is discussed, and the conclusion applies to both channels. Modulator The ISL6228 modulator features Intersil’s R3 technology, a hybrid of fixed frequency PWM control and variable frequency hysteretic control. Intersil’s R3 technology can simultaneously affect the PWM switching frequency and PWM duty cycle in response to input voltage and output load transients. The R3 modulator synthesizes an AC signal VR, which is an analog representation of the output inductor ripple current. The duty-cycle of VR is the result of charge and discharge current through a ripple capacitor CR. The FN9095.2 May 7, 2008 ISL6228 current through CR is provided by a transconductance amplifier gm that measures the VIN and VO pin voltages. The positive slope of VR can be written as Equation 1: V RPOS = ( g m ) ⋅ ( V IN – V OUT ) ⁄ C R (EQ. 1) The negative slope of VR can be written as Equation 2: V RNEG = g m ⋅ V OUT ⁄ C R Soft-Start Delay tSS begins and the output voltage begins to rise. The FB pin ramps to 0.6V in approximately 1.5ms and the PGOOD pin goes to high impedance approximately 1.25ms after the FB pin voltage reaches 0.6V. 1.5ms Vo (EQ. 2) VCC and PVCC Where gm is the gain of the transconductance amplifier. A window voltage VW is referenced with respect to the error amplifier output voltage VCOMP, creating an envelope into which the ripple voltage VR is compared. The amplitude of VW is set by a resistor connected across the FSET and GND pins. The VR, VCOMP, and VW signals feed into a window comparator in which VCOMP is the lower threshold voltage and VW is the higher threshold voltage. Figure 2 shows PWM pulses being generated as VR traverses the VW and VCOMP thresholds. The PWM switching frequency is proportional to the slew rates of the positive and negative slopes of VR; it is inversely proportional to the voltage between VW and VCOMP. Ripple Capacitor Voltage CR Window Voltage VW EN FB PGOOD 1.25ms FIGURE 3. SOFT-START SEQUENCE The PGOOD pin indicates when the converter is capable of supplying regulated voltage. The PGOOD pin is an undefined impedance if VCC has not reached the rising POR threshold VCCR, or if VCC is below the falling POR threshold VCCF. The ISL6228 features a unique fault-identification capability that can drastically reduce trouble-shooting time and effort. The pull-down resistance of the PGOOD pin corresponds to the fault status of the controller. The PGOOD pull-down resistance is 95Ω during soft-start or if an UVP occurs, 30Ω for an OCP, or 60Ω for OVP. TABLE 1. PGOOD PULL-DOWN RESISTANCE Error Amplifier Voltage VCOMP PWM CONDITION PGOOD RESISTANCE VCC Below POR Undefined Soft-start or Undervoltage 90Ω Overvoltage 60Ω Overcurrent 30Ω MOSFET Gate-Drive Outputs LGATE and UGATE FIGURE 2. MODULATOR WAVEFORMS DURING LOAD TRANSIENT Power-On Reset The ISL6228 is disabled until the voltage at the VCC pin has increased above the rising power-on reset (POR) VCCR threshold voltage. The controller will be disabled when the voltage at the VCC pin decreases below the falling POR VCCF threshold voltage. EN, Soft-Start and PGOOD The ISL6228 uses a digital soft-start circuit to ramp the output voltage of the converter to the programmed regulation setpoint at a predictable slew rate. The slew rate of the soft-start sequence has been selected to limit the in-rush current through the output capacitors as they charge to the desired regulation voltage. When the EN pin is pulled above the rising EN threshold voltage VENTHR, the PGOOD 8 The ISL6228 has internal gate-drivers for the high-side and low-side N-Channel MOSFETs. The low-side gate-drivers are optimized for low duty-cycle applications where the lowside MOSFET conduction losses are dominant, requiring a low r DS(ON) MOSFET. The LGATE pull-down resistance is small in order to clamp the gate of the MOSFET below the VGS(th) at turnoff. The current transient through the gate at turn-off can be considerable because the gate charge of a low r DS(ON) MOSFET can be large. Adaptive shoot-through protection prevents a gate-driver output from turning on until the opposite gate-driver output has fallen below approximately 1V. The dead-time shown in Figure 4 is extended by the additional period that the falling gate voltage stays above the 1V threshold. The typical dead-time is 21ns. The high-side gate-driver output voltage is measured across the UGATE and PHASE pins while the low-side gate-driver output voltage is measured across the LGATE and PGND FN9095.2 May 7, 2008 ISL6228 pins. The power for the LGATE gate-driver is sourced directly from the PVCC pin. The power for the UGATE gatedriver is sourced from a “boot” capacitor connected across the BOOT and PHASE pins. The boot capacitor is charged from a 5V bias supply through a “boot diode” each time the low-side MOSFET turns on, pulling the PHASE pin low. The ISL6228 has an integrated boot diode connected from the PVCC pin to the BOOT pin. tLGFUGR tUGFLGR 50% UGATE LGATE detected positive voltage and LGATE was allowed to go high for eight consecutive PWM switching cycles. The ISL6228 will turn off the low-side MOSFET once the phase voltage turns positive, indicating negative inductor current. The ISL6228 will return to CCM on the following cycle after the PHASE pin detects negative voltage, indicating that the body diode of the low-side MOSFET is conducting positive inductor current. Efficiency can be further improved with a reduction of unnecessary switching losses by reducing the PWM frequency. It is characteristic of the R3 architecture for the PWM frequency to decrease while in diode emulation. The extent of the frequency reduction is proportional to the reduction of load current. Upon entering DEM, the PWM frequency makes an initial step-reduction because of a 33% step-increase of the window voltage V W. Overcurrent Protection The overcurrent protection (OCP) setpoint is programmed with resistor ROCSET that is connected across the OCSET and PHASE pins. 50% L DCR FIGURE 4. LGATE AND UGATE DEAD-TIME Diode Emulation + ISL6228 The ISL6228 implements forced continuous-conductionmode (CCM) at heavy load and diode-emulation-mode (DEM) at light load, to optimize efficiency in the entire load range. The transition is automatically achieved by detecting the output load current. Positive-going inductor current flows from either the source of the high-side MOSFET, or the drain of the low-side MOSFET. Negative-going inductor current flows into the drain of the low-side MOSFET. When the low-side MOSFET conducts positive inductor current, the phase voltage will be negative with respect to the GND and PGND pins. Conversely, when the low-side MOSFET conducts negative inductor current, the phase voltage will be positive with respect to the GND and PGND pins. The ISL6228 monitors the phase voltage, when the low-side MOSFET is conducting inductor current, to determine the direction of the inductor current. When the output load current is greater than or equal to ½ the inductor ripple current, the inductor current is always positive, and the converter is always in CCM. The ISL6228 minimizes the conduction loss in this condition by forcing the low-side MOSFET to operate as a synchronous rectifier. When the output load current is less than ½ the inductor ripple current, negative inductor current occurs. Sinking negative inductor through the low-side MOSFET lowers efficiency through unnecessary conduction losses. The ISL6228 automatically enters DEM after the PHASE pin has 9 IL PHASE 10µA OCSET ROCSET + VROCSET VDCR CSEN VO _ CO _ RO VO FIGURE 5. OVERCURRENT-SET CIRCUIT Figure 5 shows the overcurrent-set circuit. The inductor consists of inductance L and the DC resistance DCR. The inductor DC current IL creates a voltage drop across DCR, given by Equation 3: V DCR = I L • DCR (EQ. 3) The ISL6228 sinks 10µA current into the OCSET pin, creating a DC voltage drop across the resistor ROCSET, given by Equation 4: V ROCSET = 10μA • R OCSET (EQ. 4) Resistor RO is connected between the VO pin and the actual output voltage of the converter. During normal operation, the VO pin is a high impedance path, therefore there is no voltage drop across RO. The DC voltage difference between the OCSET pin and the VO pin can be established using Equation 5: V OCSET – V VO = V DCR – V ROCSET = I L • DCR – 10μA • R OCSET (EQ. 5) FN9095.2 May 7, 2008 ISL6228 The ISL6228 monitors the OCSET pin and the VO pin voltages. Once the OCSET pin voltage is higher than the VO pin voltage for more than 10µs, the ISL6228 declares an OCP fault. The value of ROCSET is then written as Equation 6: I OC • DCR R OCSET = --------------------------10μA (EQ. 6) Where: - ROCSET (Ω) is the resistor used to program the overcurrent setpoint - IOC is the output current threshold that will activate the OCP circuit - DCR is the inductor DC resistance For example, if IOC is 20A and DCR is 4.5mΩ, the choice of ROCSET is ROCSET = 20A x 4.5mΩ/10µA = 9kΩ. Resistor ROCSET and capacitor CSEN form an R-C network to sense the inductor current. To sense the inductor current correctly not only in DC operation, but also during dynamic operation, the R-C network time constant ROCSETCSEN needs to match the inductor time constant L/DCR. The value of CSEN is then written as Equation 7: L C SEN = ----------------------------------------R OCSET • DCR (EQ. 7) For example, if L is 1.5µH, DCR is 4.5mΩ, and ROCSET is 9kΩ, the choice of CSEN = 1.5µH/(9kΩ x 4.5mΩ) = 0.037µF. Upon converter startup, capacitor CSEN initial voltage is 0V. To prevent false OCP, a 10µA current source flows out of the VO pin during start up, generating a voltage drop on resistor RO, which has the same resistance as ROCSET. When PGOOD pin goes high, the VO pin current source will terminate. When an OCP fault is declared, the PGOOD pin will pull down to 30Ω and latch off the converter. The fault will remain latched until the EN pin has been pulled below the falling EN threshold voltage VENTHF or if VCC has decayed below the falling POR threshold voltage VVCC_THF. Overvoltage Protection The OVP fault detection circuit triggers after the FB pin voltage is above the rising overvoltage threshold VOVR for more than 2µs. The FB pin voltage is 0.6V in normal operation. The rising overvoltage threshold VOVR is typically 116%. That means if the FB pin voltage is above 116% x 0.6V = 0.696V, for more than 2µs, an OVP fault is declared. When an OVP fault is declared, the PGOOD pin will pull down to 60Ω and latch-off the converter. The OVP fault will remain latched until the EN pin has been pulled below the falling EN threshold voltage VENTHF or if VCC has decayed below the falling POR threshold voltage VVCC_THF. Although the converter has latched-off in response to an OVP fault, the LGATE gate-driver output will retain the ability to toggle the low-side MOSFET on and off, in response to 10 the output voltage transversing the VOVR and VOVF thresholds. The LGATE gate-driver will turn on the low-side MOSFET to discharge the output voltage, protecting the load. The LGATE gate-driver will turn off the low-side MOSFET once the FB pin voltage is lower than the falling overvoltage threshold VOVF for more than 2µs. The falling overvoltage threshold VOVF is typically 106%. That means if the FB pin voltage falls below 106% x 0.6V = 0.636V, for more than 2µs, the LGATE gate-driver will turn off the lowside MOSFET. If the output voltage rises again, the LGATE driver will again turn on the low-side MOSFET when the FB pin voltage is above the rising overvoltage threshold VOVR for more than 2µs. By doing so, the ISL6228 protects the load when there is a consistent overvoltage condition. Undervoltage Protection The UVP fault detection circuit triggers after the FB pin voltage is below the undervoltage threshold VUV for more than 2µs. The FB pin voltage is 0.6V in normal operation. The undervoltage threshold VUV is typically 86%. That means if the FB pin voltage is below 86% x 0.6V = 0.516V, for more than 2µs, an UVP fault is declared, and the PGOOD pin will pull down to 95Ω and latch-off the converter. The fault will remain latched until the EN pin has been pulled below the falling EN threshold voltage VENTHF or if VCC has decayed below the falling POR threshold voltage V VCC_THF. Programming the Output Voltage When the converter is in regulation there will be 0.6V from the FB pin to the GND pin. Connect a two-resistor voltage divider across the VO pin and the GND pin with the output node connected to the FB pin. Scale the voltage-divider network such that the FB pin is 0.6V with respect to the GND pin when the converter is regulating at the desired output voltage. The output voltage can be programmed from 0.6V to 5V. Programming the output voltage is written as Equation 8: R BOTTOM V REF = V O • -------------------------------------------------R TOP + R BOTTOM (EQ. 8) Where: - VO is the desired output voltage of the converter - The voltage to which the converter regulates the FB pin is the VREF - RTOP is the voltage-programming resistor that connects from the FB pin to the converter output. In addition to setting the output voltage, this resistor is part of the loop compensation network - RBOTTOM is the voltage-programming resistor that connects from the FB pin to the GND pin Choose RTOP value first, and calculate RBOTTOM according to Equation 9: V REF • R TOP R BOTTOM = ----------------------------------V O – V REF (EQ. 9) FN9095.2 May 7, 2008 ISL6228 Programming the PWM Switching Frequency General Application Design Guide The ISL6228 does not use a clock signal to produce PWMs. The PWM switching frequency fSW is programmed by the resistor RFSET that is connected from the FSET pin to the GND pin. The approximate PWM switching frequency is written as Equation 10: This design guide is intended to provide a high-level explanation of the steps necessary to design a single-phase power converter. It is assumed that the reader is familiar with many of the basic skills and techniques referenced in the following section. In addition to this guide, Intersil provides complete reference designs that include schematics, bills of materials, and example board layouts. 1 f SW = --------------------------K ⋅ R FSET (EQ. 10) Estimating the value of RFSET is written as Equation 11: 1 R FSET = -----------------K • f SW (EQ. 11) Where: - fSW is the PWM switching frequency - RFSET is the fSW programming resistor - K = 1.5 x 10-10 Selecting the LC Output Filter The duty cycle of an ideal buck converter is a function of the input and the output voltage. This relationship is written as Equation 13: VO D = --------V IN It is recommended that whenever the control loop compensation network is modified, fSW should be checked for the correct frequency and if necessary, adjust RFSET. (EQ. 13) The output inductor peak-to-peak ripple current is written as Equation 14: VO • ( 1 – D ) I PP = -----------------------------f SW • L (EQ. 14) Compensation Design Figure 6 shows the recommended Type-II compensation circuit. The FB pin is the inverting input of the error amplifier. The COMP signal, the output of the error amplifier, is inside the chip and unavailable to users. CINT is a 100pF capacitor integrated inside the IC, connecting across the FB pin and the COMP signal. RTOP, RFB, CFB and CINT form the Type-II compensator. The frequency domain transfer function is given by Equation 12: 1 + s • ( R TOP + R FB ) • C FB G COMP ( s ) = ------------------------------------------------------------------------------------------s • R TOP • C INT • ( 1 + s • R FB • C ) (EQ. 12) FB CINT = 100pF CFB RFB RTOP - VO FB EA RBOTTOM COMP + A typical step-down DC/DC converter will have an IP-P of 20% to 40% of the maximum DC output load current. The value of IPP is selected based upon several criteria such as MOSFET switching loss, inductor core loss, and the resistive loss of the inductor winding. The DC copper loss of the inductor can be estimated by Equation 15: P COPPER = I LOAD 2 • DCR (EQ. 15) Where ILOAD is the converter output DC current. The copper loss can be significant so attention has to be given to the DCR selection. Another factor to consider when choosing the inductor is its saturation characteristics at elevated temperature. A saturated inductor could cause destruction of circuit components, as well as nuisance OCP faults. A DC/DC buck regulator must have output capacitance CO into which ripple current IP-P can flow. Current IPP develops a corresponding ripple voltage VP-P across CO, which is the sum of the voltage drop across the capacitor ESR and of the voltage change stemming from charge moved in and out of the capacitor. These two voltages are written as Equation 16: REF ΔV ESR = I P-P • E SR ISL6228 FIGURE 6. COMPENSATION REFERENCE CIRCUIT The LC output filter has a double pole at its resonant frequency that causes rapid phase change. The R3 modulator used in the ISL6228 makes the LC output filter resemble a first order system in which the closed loop stability can be achieved with the recommended Type-II compensation network. Intersil provides a PC-based tool (example page is shown later) that can be used to calculate compensation network component values and help simulate the loop frequency response. 11 (EQ. 16) and Equation 17: I P-P ΔV C = ----------------------------8 • CO • f (EQ. 17) SW If the output of the converter has to support a load with high pulsating current, several capacitors will need to be paralleled to reduce the total ESR until the required VP-P is achieved. The inductance of the capacitor can cause a brief voltage dip if the load transient has an extremely high slew rate. Low inductance capacitors should be considered. A capacitor FN9095.2 May 7, 2008 ISL6228 dissipates heat as a function of RMS current and frequency. Be sure that IP-P is shared by a sufficient quantity of paralleled capacitors so that they operate below the maximum rated RMS current at fSW. Take into account that the rated value of a capacitor can fade as much as 50% as the DC voltage across it increases. Selection of the Input Capacitor MOSFET Selection and Considerations Typically, a MOSFET cannot tolerate even brief excursions beyond their maximum drain to source voltage rating. The MOSFETs used in the power stage of the converter should have a maximum VDS rating that exceeds the sum of the upper voltage tolerance of the input power source and the voltage spike that occurs when the MOSFET switches off. The important parameters for the bulk input capacitance are the voltage rating and the RMS current rating. For reliable operation, select bulk capacitors with voltage and current ratings above the maximum input voltage and capable of supplying the RMS current required by the switching circuit. Their voltage rating should be at least 1.25 times greater than the maximum input voltage, while a voltage rating of 1.5 times is a preferred rating. Figure 7 is a graph of the input RMS ripple current, normalized relative to output load current, as a function of duty cycle that is adjusted for converter efficiency. The ripple current calculation is written as Equation 18: There are several power MOSFETs readily available that are optimized for DC/DC converter applications. The preferred high-side MOSFET emphasizes low gate charge so that the device spends the least amount of time dissipating power in the linear region. Unlike the low-side MOSFET which has the drain-source voltage clamped by its body diode during turn off, the high-side MOSFET turns off with VIN - VOUT, plus the spike, across it. The preferred low-side MOSFET emphasizes low r DS(ON) when fully saturated to minimize conduction loss. 2 2 D 2 ( I MAX ⋅ ( D – D ) ) + ⎛ x ⋅ I MAX ⋅ ------ ⎞ ⎝ 12 ⎠ I IN_RMS, NORMALIZED = ----------------------------------------------------------------------------------------------------I MAX P CON_LS ≈ I LOAD ⋅ r DS ( ON )_LS • ( 1 – D ) (EQ. 18) Where: - IMAX is the maximum continuous ILOAD of the converter - x is a multiplier (0 to 1) corresponding to the inductor peak-to-peak ripple amplitude expressed as a percentage of IMAX (0% to 100%) - D is the duty cycle that is adjusted to take into account the efficiency of the converter which is written as: VO D = -------------------------V IN ⋅ EFF (EQ. 19) NORMALIZED INPUT RMS RIPPLE CURRENT In addition to the bulk capacitance, some low ESL ceramic capacitance is recommended to decouple between the drain of the high-side MOSFET and the source of the low-side MOSFET. 0.60 0.55 0.50 2 (EQ. 20) For the high-side (HS) MOSFET, the its conduction loss is written as Equation 21: P CON_HS = I LOAD 2 • r DS ( ON )_HS • D (EQ. 21) For the high-side MOSFET, the switching loss is written as Equation 22: V IN • I VALLEY • t ON • f V IN • I PEAK • t OFF • f SW SW P SW_HS = ----------------------------------------------------------------- + ------------------------------------------------------------2 2 (EQ. 22) Where: - IVALLEY is the difference of the DC component of the inductor current minus 1/2 of the inductor ripple current - IPEAK is the sum of the DC component of the inductor current plus 1/2 of the inductor ripple current - tON is the time required to drive the device into saturation - tOFF is the time required to drive the device into cut-off Selecting The Bootstrap Capacitor 0.45 The selection of the bootstrap capacitor is written as Equation 23: 0.40 0.35 0.30 Qg C BOOT = -----------------------ΔV BOOT x=1 x = 0.75 x = 0.50 x = 0.25 x=0 0.25 0.20 0.15 0.05 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 DUTY CYCLE FIGURE 7. NORMALIZED RMS INPUT CURRENT 12 (EQ. 23) Where: 0.10 0 0 For the low-side (LS) MOSFET, the power loss can be assumed to be conductive only and is written as Equation 20: 1.0 - Qg is the total gate charge required to turn on the high-side MOSFET - ΔVBOOT, is the maximum allowed voltage decay across the boot capacitor each time the high-side MOSFET is switched on FN9095.2 May 7, 2008 ISL6228 As an example, suppose the high-side MOSFET has a total gate charge Qg, of 25nC at VGS = 5V, and a ΔVBOOT of 200mV. The calculated bootstrap capacitance is 0.125µF; for a comfortable margin, select a capacitor that is double the calculated capacitance. In this example, 0.22µF will suffice. Use an X7R or X5R ceramic capacitor. Layout Considerations As a general rule, power should be on the bottom layer of the PCB and weak analog or logic signals are on the top layer of the PCB. The ground-plane layer should be adjacent to the top layer to provide shielding. The ground plane layer should have an island located under the IC, the compensation components, and the FSET components. The island should be connected to the rest of the ground plane layer at one point. VIAS TO GROUND PLANE GND VOUT INDUCTOR PHASE NODE HIGH-SIDE MOSFETS VIN OUTPUT CAPACITORS SCHOTTKY DIODE EN (Pins 11 and 24), and PGOOD (Pins 7 and 28) These are logic signals that are referenced to the GND pin. Treat as a typical logic signal. OCSET (Pins 10 and 25) The current-sensing network consisting of ROCSET and CSEN needs to be connected to the inductor pads for accurate measurement. Connect ROCSET to the phasenode side pad of the inductor, and connect CSEN to the output side pad of the inductor. Connect the OCSET pin to the common node of node of ROCSET and CSEN. FB (Pins 8 and 27), and VO (Pins 9 and 26) The VO pin is used to sense the inductor current for OCP. Connect the VO pin to the output-side of CSEN through resistor RO. The input impedance of the FB pin is high, so place the voltage programming and loop compensation components close to the VO, FB, and GND pins keeping the high impedance trace short. FSET (Pins 1 and 6) LOW-SIDE MOSFETS This pin requires a quiet environment. The resistor RFSET and capacitor CFSET should be placed directly adjacent to this pin. Keep fast moving nodes away from this pin. INPUT CAPACITORS LGATE (Pins 16 and 19) FIGURE 8. TYPICAL POWER COMPONENT PLACEMENT Signal Ground and Power Ground The bottom of the ISL6228 TQFN package is the signal ground (GND) terminal for analog and logic signals of the IC. Connect the GND pad of the ISL6228 to the island of ground plane under the top layer using several vias, for a robust thermal and electrical conduction path. Connect the input capacitors, the output capacitors, and the source of the lower MOSFETs to the power ground plane. PGND (Pins 17 and 18) This is the return path for the pull-down of the LGATE low-side MOSFET gate driver. Ideally, PGND should be connected to the source of the low-side MOSFET with a low-resistance, low-inductance path. VIN (Pins 2 and 5) The VIN pin should be connected close to the drain of the high-side MOSFET, using a low resistance and low inductance path. VCC (Pins 3 and 4) The signal going through this trace is both high dv/dt and high di/dt, with high peak charging and discharging current. Route this trace in parallel with the trace from the PGND pin. These two traces should be short, wide, and away from other traces. There should be no other weak signal traces in proximity with these traces on any layer. BOOT (Pins 14 and 21), UGATE (Pins 13 and 22), and PHASE (Pins 12 and 23) The signals going through these traces are both high dv/dt and high di/dt, with high peak charging and discharging current. Route the UGATE and PHASE pins in parallel with short and wide traces. There should be no other weak signal traces in proximity with these traces on any layer. Copper Size for the Phase Node The parasitic capacitance and parasitic inductance of the phase node should be kept very low to minimize ringing. It is best to limit the size of the PHASE node copper in strict accordance with the current and thermal management of the application. An MLCC should be connected directly across the drain of the upper MOSFET and the source of the lower MOSFET to suppress the turn-off voltage spike. For best performance, place the decoupling capacitor very close to the VCC and GND pins. PVCC (Pins 15 and 20) For best performance, place the decoupling capacitor very close to the PVCC and respective PGND pins, preferably on the same side of the PCB as the ISL6228 IC. 13 FN9095.2 May 7, 2008 ISL6228 Typical Performance 100 100 VIN = 8V 95 95 90 90 85 EFFICIENCY (%) EFFICIENCY (%) VIN = 8V VIN = 12V VIN = 19V 80 75 85 80 75 70 70 65 65 60 VIN = 12V VIN = 19V 60 0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7 8 IOUT (A) IOUT (A) FIGURE 9. CHANNEL 1 EFFICIENCY AT VO = 1.5V VO1 FB1 FIGURE 10. CHANNEL 2 EFFICIENCY AT VO = 1.8V VO1 FB1 PGOOD1 PGOOD1 PHASE1 PHASE1 FIGURE 11. START-UP, VIN = 12V, LOAD = 0.25Ω, VO = 1.05V VO1 FIGURE 12. SHUT-DOWN, VIN = 12V, IO = 10A, VO = 1.05V VO1 PHASE1 PHASE1 VO2 VO2 PHASE2 PHASE2 FIGURE 13. CCM STEADY-STATE OPERATION,VIN = 12V, VO1 = 1.5V, IO1 = 3A, VO2 = 1.8A, IO2 = 4A 14 FIGURE 14. DCM STEADY-STATE OPERATION,VIN = 12V, VO1 = 1.5V, IO1 = 1A, VO2 = 1.8V, IO2 = 1A FN9095.2 May 7, 2008 ISL6228 Typical Performance (Continued) IO1 IO2 VO1 VO2 PHASE2 PHASE1 FIGURE 15. TRANSIENT RESPONSE, VIN = 12V, VO = 1.5V, IO = 0.1A/8.1A @ 2.55A/µs FIGURE 16. TRANSIENT RESPONSE, VIN = 12V, VO = 1.8V, IO = 0.1A/8.1A @ 2.55A/µs IO1 IO2 VO1 VO2 PHASE1 FIGURE 17. LOAD INSERTION RESPONSE, VIN = 12V, VO = 1.5V, IO = 0.1A/8.1A @ 2.55A/µs IO1 VO1 PHASE1 FIGURE 19. LOAD RELEASE RESPONSE, VIN = 12V, VO = 1.5V, IO = 0.1A/8.1A @ 2.55A/µs PHASE2 FIGURE 18. LOAD INSERTION RESPONSE, VIN = 12V, VO = 1.8V, IO = 0.1A/8.1A @ 2.55A/µs IO2 VO2 PHASE2 FIGURE 20. LOAD RELEASE RESPONSE, VIN = 12V, VO = 1.8V, IO = 0.1A/8.1A @ 2.55A/µs All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 FN9095.2 May 7, 2008 ISL6228 Package Outline Drawing L28.4x4A 28 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 0, 3/07 4X 2.4 4.00 24X 0.40 A B 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 28 22 1 4.00 21 2 .40 ± 0 . 15 15 (4X) 0.15 8 14 0.10 M C A B 4 28X 0.20 TOP VIEW 28X 0.45 ± 0.10 BOTTOM VIEW SEE DETAIL "X" 0.10 C 0 . 75 ( 3. 75 TYP ) ( 24X 0 . 4 ) ( C BASE PLANE SEATING PLANE 0.08 C 2. 40 ) SIDE VIEW ( 28X 0 . 20 ) C 0 . 2 REF 5 0 . 00 MIN. 0 . 05 MAX. ( 28X 0 . 65) TYPICAL RECOMMENDED LAND PATTERN DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 16 FN9095.2 May 7, 2008