USB Type-C Demo Kit V2 QuickSTART The Lattice USB Type-C Demo Kit V2 is designed to demonstrate the Lattice USB Type-C power delivery (PD) solution. This document provides a brief introduction and instructions to install and run basic Type-C features demo using USB Type-C Demo Kit V2. The Type-C operation requires two port partners. This Quick Start Demo utilizes one Lattice board and one external port partner such as a PC or Tablet with a Type-C interface. There are two versions of this board, as identified by the Ordering Part Number. This document is applicable to either version, with the notes as applicable. Power Switch (SW2) LEDs (D1-D8) LEDs (D17-D25) FTDI Chip (U1) USB 2.0 Mini-B (J2) LEDs (D26-D33) LCMXO2-40000ZE (U4) DP Connector UFP (CN1) 10 Bit Switch (SW3) DP Connector DFP (CN2) iCE40LP8K (U22) HD3SS460 (U11) P13D6S3224 (U19) SN8F22511BX (U13) Header Pool 5V DC Power Jack (J8) iCE5LP4K (U5) Boost Regulator (U18) USB 3.1 Type-C Receptacle (CN2) USB 3.1 Type-A Receptacle (J6) GREEN iCE40LP8K-USBC-EVN only BLUE iCE5LPK4K-USBC-EVN only BLACK included in both versions Figure 1: Top View of the Kit showing layout of components 1 Check Kit Contents USB Type-C Demo Kit V2 based on ordering part number (iCE40LP8K-USBC-EVN (U22) / iCE40LP4K-USBC-EVN (U5)) Type-C to Type-C Cable Type-A to Type mini-B cable USB 3.0 Type-A to Type-A cable USB 3.0 Memory Stick , 8GB (Type-A connector) Mini DP to DP cable (iCE40LP8K-USBC-EVN Version only) 5V DC Power Adapter USB Type-C Demo Kit V2 2 Additional Requirements PC/TABLET with Tera Term support (other terminal emulators also can be used). Tera Term is an open source free software terminal emulator supporting the UTF-8 protocol. A download link is available at http://www.latticesemi.com/usbcv2 PC/TABLET with Type-C support Note: Detailed information about the Kit is provided in the USB Type-C demo kit V2 board user guide (EB99). The Kit has all the default settings enabled at manufacture. To run the default demo mentioned in this document, do not change the default settings. 3 Storage and Handling Tips Static electricity can shorten the lifespan of electronic components. Note the following tips to prevent damage which occurs from electro-static discharge: 4 Use anti-static precautions such as operating on an anti-static mat and wearing an anti-static wristband. Keep the USB Type-C demo kit V2 Board in the anti-static bag provided. Touch the metal USB housing to equalize voltage potential between you and the board. USB Type-C Feature Test Steps Note: PD transaction logging supported only for iCE40LP8K-USBC-EVN. For iCE40LP4K-USBC-EVN, skip steps 1 to 3 and start from step 4. 1. 2. 3. Install Tera term in PC/Tablet Connect Type- A to Min-B cable from PC/Tablet to USB Mini-B port (J2) of the USB Type-C demo kit V2. Set the serial port setting in the tera term as shown Figure 2. Note: COM port may be different than shown. Figure 2 : Serial Port Settings USB Type-C Demo Kit V2 4. 5. 6. Connect an external power adapter to the USB Type-C demo kit V2. Switch on the power switch SW2. Connect Type-C cable between the USB Type-C demo kit V2 and PC/Tablet with Type-C port as shown in Figure 3. Type-C cable iCE40LP8K/iCE5LP4K USB Type-C EVN USB Type-C receptacle USB Type-C receptacle Power Adapter Type-A to Mini-B cable Figure 3: Type-C feature test setup 7. See PD transaction on the Tera term terminal (iCE40LP8KUSBC-EVN only). Refer Figure 4 for the status. Figure 4: PD Transaction on terminal 8. Refer Table 1 for the power delivery (PD) LEDs status on board LEDS DESCRIPTION COLOR D17 Cable attached Blue D18 Flip Blue D20 PD contact established Blue D31 VBUS 5V Yellow D19 Source/sink Blue D21 PDO1 Green D28 SS POL Blue D29 SS SEL Blue D30 SS enable Yellow Table 1: LEDs Status USB Type-C Demo Kit V2 5 DONE! You have successfully demonstrated the basic Type-C features on USB Type-C demo kit V2. Refer USB Type-C demo kit V2 user guides (UG94 and EB99) available on the website at http://www.latticesemi.com/usbcv2 for the following: Running advanced demos Details on additional evaluation board features and operation Programming the MachXO2, iCE40LP8K/iCE5LP4K devices using USB cable Schematics BOM Additional Terms and Conditions Applicable to Lattice Programming and Development Hardware Lattice device programmers, programming cables, socket adapters, and other hardware sold for use in conjunction with Lattice software (“Programming Hardware”) and Lattice evaluation boards and development kits sold for use in conjunction with evaluating Lattice products (“Development Hardware”) are designed and intended for use solely with semiconductor components manufactured by Lattice Semiconductor Corporation. Programming and Development Hardware is warranted to meet Lattice specifications only for a period of ninety (90) days; in all other respects the terms and conditions of sale of Programming and Development Hardware shall be Lattice’s standard terms and conditions set forth in Lattice’s Sales Order Acknowledgment. Additionally, Lattice specifications for Programming and Development Hardware limit their use to low-volume engineering applications only, and not for volume production use. The warranty for Programming and Development Hardware will not apply to any Programming or Development Hardware used in production, used with worn or improperly installed hardware, or used with incompatible systems or components. Technical Support [email protected] Copyright © 2015 Lattice Semiconductor Corporation. Lattice Semiconductor, L (stylized) Lattice Semiconductor Corp., Lattice (design), Lattice Diamond and iCE40 UltraLite are either registered trademarks or trademarks of Lattice Semiconductor Corporation in the United States and/or other countries. Other product names used in this publication are for identification purposes only and may be trademarks of their respective companies. QS031 Rev. 1 June 2015