Datasheet

CCD multichannel detector heads
C7040
C7041
Designed for back-thinned CCD area image
sensor
The C7040 and C7041 are high sensitivity multichannel detector heads for use with back-thinned CCD area image sensors (S7030/
S7031 series, S11500-1007, S11501-1007S) that offer high UV sensitivity and quantum efficiency. The C7040 is designed for the
non-cooled type (S7030 series, S11500-1007), while the C7041 for the one-stage TE-cooled type (S7031 series, S11501-1007S)
for detection at even lower light levels. Both the C7040 and C7041 incorporate a low-noise driver/amplifier circuit that provides
reliable operation from simple external signals. The C7041 also includes a highly stable temperature controller that cools the sensor to a preset temperature level (Ts=-10 °C) as soon as the power is turned on. If the cooler fails and causes internal circuitry
to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler. Despite its compact
size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers. The table (P.2) shows back-thinned CCD image sensors for the C7040 and
C7041. The C7040 and C7041 do not come with a CCD image sensor, so select the desired sensor and order it separately.
Controller for multichannel detector head C7557-01 is also available. The software supplied with the C7557-01 allows easy control of the multichannel detector head and data acquisition.
Features
Applications
Designed for back-thinned CCD area image sensor*1
C7040: for non-cooled type (S7030 series, S11500-1007)
C7041: for TE-cooled type (S7031 series, S11501-1007S)
Fluorescence spectroscopy
Line binning operation*2/area scanning operation
Raman spectroscopy
Other low-light-level detection
Driver/amplifier circuit for low noise CCD operation
Highly stable temperature controller (C7041)
Cooling temperature: -10 °C ± 0.05 °C
Simple signal input operation
Compact configuration
*1: In normal CCD image sensors that receive light from the front surface, the active area is covered with electrodes for charge transfer.
These electrodes cut off UV radiation incident on the image sensor and also reduce the quantum efficiency. In contrast, back-thinned
CCD image sensors have a unique structure in which the back of the active area is finely ground to allow light to enter from the
back surface. This structure ensures high UV sensitivity and quantum efficiency because incident light need not pass through the
electrodes.
*2: The CCD area image sensor can be operated like a linear image sensor having a large active area by transferring all the pixel signals in
the vertical direction to the horizontal register (this is referred to as line binning).
www.hamamatsu.com
1
CCD multichannel detector heads
C7040, C7041
Selection guide
The table below shows CCD area image sensors applicable for the C7040 and C7041.
Since the C7040 and C7041 do not include a CCD area image sensor, so select the desired sensor and order it separately.
CCD area image sensor
Type No.
Active area
[mm (H) × mm (V)]
S7030-0906
532 × 64
512 × 58
12.288 × 1.392
S7030-0907
532 × 128
512 × 122
12.288 × 2.928
S7030-0908
532 × 256
512 × 250
12.288 × 6.000
C7040
S7030-1006
1044 × 64
1024 × 58
24.576 × 1.392
S7030-1007
1044 × 128
1024 × 122
24.576 × 2.928
S7030-1008
1044 × 256
1024 × 250
24.576 × 6.000
S11500-1007
1044 × 128
1024 × 122
24.576 × 2.928
S7031-0906S
532 × 64
512 × 58
12.288 × 1.392
S7031-0907S
532 × 128
512 × 122
12.288 × 2.928
S7031-0908S
532 × 256
512 × 250
12.288 × 6.000
C7041
S7031-1006S
1044 × 64
1024 × 58
24.576 × 1.392
S7031-1007S
1044 × 128
1024 × 122
24.576 × 2.928
S7031-1008S
1044 × 256
1024 × 250
24.576 × 6.000
1024 × 122
24.576 × 2.928
S11501-1007S
1044 × 128
Note: CCD multichannel detector head C7042 for two-stage TE-cooled CCD area image sensor S7032/-1006/-1007/-1008 is also available.
Type No.
Number of pixels
Number of active pixels
Absolute maximum ratings
Parameter
Supply voltage (for digital circuitry)
Supply voltage (for analog circuitry)
Supply voltage
Digital input voltage
C7040
Operating temperature
C7041
C7040
Storage temperature
C7041
Symbol
VD1
VA1+
VA1VA2
VD2
Vp
VF
Topr
Tstg
Min.
-0.5
0
+10
-20
0
Typ.
-
Max.
+7
+18
-18
+30
+7
+7
+14
VD (1, 2)
+50
+35*3
+70
+50
Unit
V
°C
*3: The maximum value may be lower, depending on the drive frequency and the number of sensor pixels.
Electrical characteristics
(Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V, unless otherwise noted)
Parameter
High level
Low level
Digital input
CLK frequency
Data video readout frequency
Start pulse width
High level (Io=-6 mA)
Low level (Io=+6 mA)
Power supply operating conditions
Digital circuitry
Digital output
Analog circuitry
Voltage
Other
Current
VD1 (+5 VDC)
VA1+ (+15 VDC)
VA1- (-15 VDC)
VA2 (+24 VDC)
VD2 (+5 VDC)*4
Vp (+5 DC)*4
VF (+12 VDC)*4
Symbol
VIH
VIL
fCLK
fv
tst
VIH
VIL
Min.
+2.0
-0.5
1/fCLK
+2.0
-
Typ.
-
Max.
VD (1, 2)
+0.8
1
fCLK/4
+0.8
Unit
V
V
MHz
Hz
s
V
V
VD1
VA1+
VA1VA2
VD2
Vp
VF
-
+4.75
+14.5
-14.5
+23.5
+4.75
+4.75
+11.75
-
+5.0
+15.0
-15.0
+24.0
+5.0
+5.0
+12.0
+100
+5.25
+15.5
-15.5
+24.5
+5.25
+5.25
+12.25
+200
+100
-100
+30
+30
+2.5
-
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
A
mA
*4: C7041
2
CCD multichannel detector heads
C7040, C7041
Electrical and optical characteristics
(Ta=25 °C, Ts=-10 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V)
Parameter
Spectral response range
Vertical
Full well capacity
Horizontal
Conversion gain*5
C7040 (Ta=25 °C)
Dark current*6
C7041 (Ta=-10 °C)
Readout noise
Dynamic range
Photo response non-uniformity*7
Symbol
λ
Min.
240
800
-
Fw
Sv
DS
Nr
DR
PRNU
Typ.
200 to 1100
320
1000
15
100
3
20
33333
±3
Max.
1000
30
±10
Unit
nm
keμV/ee-/pixel/s
e- rms
%
*5: Including the circuit gain
*6: At MPP mode. Vertical register value. The actual value equals the sum of the vertical direction because of the binning operation.
*7: Measured at 50 % of the full well capacity
Specifications for temperature controller (C7041)
(Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V)
Parameter*8
Cooling temperature
Temperature control range
Power dissipation of TE-cooler element
Cool down time to reset temperature
Setting temperature for overheat protection*9
Symbol
Ts
Min.
-11
-0.05
-
ΔTs
Pp
to
To
Typ.
-10
+45
Max.
-9
+0.05
7
5
-
Unit
°C
°C
W
min
°C
*8: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor.
*9: Temperature on the rear of the case (where the fan is installed)
Spectral response (without window)
(Typ. Ta=25 °C)
100
S7030/S7031 series
90
S11500-1007
S11501-1007S
Quantum efficiency (%)
80
70
60
50
40
30
20
Front-illuminated CCD
10
0
200
400
600
800
1000
1200
Wavelength (nm)
KMPDB0038EC
3
CCD multichannel detector heads
C7040, C7041
Dark current vs. temperature
(Typ.)
1000
Dark current (e-/pixel/s)
100
10
1
0.1
0.01
-50
-40
-20
-30
-10
0
10
20
30
Temperature (°C)
KMPDB0256EA
Device structure (S7030/S7031 series)
Thinning
23
21
15
20
13
14
2-bevel
22
24
1
n
H
2 signal out
5
4
3
2
12345
4-bevel
Thinning
V
12
2
11
3
4
5
8
10
9
n
Blank (4 pixels)
Blank (4 pixels)
2 signal out
6-bevel
V=58, 122, 250
H=512, 1024
6-bevel
KMPDC0016EB
4
CCD multichannel detector heads
C7040, C7041
Block diagram (C7041)
P+
Vp (+5V)
P.GND
VD2 (+5V)
D.GND
PLED
TH+
TH-
F.GND
Temp monitor
Cooling control
VD1 (+5V)
D.GND
VA1+ (+15V)
VA1- (-15V)
A.GND
Temperature controller *
TE-cooler
OD
RD
OG
IG1H, IG2H
IG1V, IG2V
P1V, P2V, TG
P1H, P2H
SG
RG
TH.H
Regulator
VA2 (+24V)
Start
CLK
VEE
VDD
VF (+12V)
Driver
Timing
generator
EOS
Trigger
Mode select
SS, ISV, ISH
Buffer
Data video
OS
Pre-amp
CCD area image sensor
S7031 series
* The C7040 does not include the temperature controller and TE-cooler.
Inverter
Clamp
Low-pass
filter
KACCC0078EB
KACCC0078EB
5
CCD multichannel detector heads
C7040, C7041
Timing chart (line binning operation)
Start
CLK
P1V
P2V
TG
P1H
P2H
SG
RG
Clamp
EOS
Trigger
Data video
V-ch1
H-ch10
H-ch11
V-ch2
H-ch(N-10) H-ch(N-9)
V-ch(M)
H-ch1
H-ch2
H-ch(N)
M=64, 128, 256 N=532, 1044
V-ch1--V-ch2, V-ch (M-3)--V-ch (M): Isolation pixels
H-ch1--H-ch4, H-ch (N-3)--H-ch (N): Blank pixels
H-ch5--H-ch10, H-ch (N-9)--H-ch (N-4): Isolation pixels
KACCC0079EC
6
CCD multichannel detector heads
C7040, C7041
Pin connections of "SIGNAL I/O" connector
15-pin D-sub connector
8
7
15
6
14
5
13
4
12
3
11
2
10
1
9
KACCC0069EA
Pin No.
Terminal name
1
Mode select
2
3
4
5
Data video
VA1+ (+15 V)
VA1- (-15 V)
VD1 (+5 V)
6
Start
7
CLK
8
EOS
9
10
11
12
13
14
15
A.GND
A.GND
VA2 (+24 V)
D.GND
D.GND
D.GND
Trigger
Description
Digital input signal used to select between the line binning operation and area scanning operation.
HCMOS compatible.
High level or left open: line binning operation
Low level: area scanning operation
Analog video output. Positive polarity.
Analog power supply
Analog power supply
Digital power supply
Digital input signal for initializing the circuit.
HCMOS compatible. Positive logic.
The interval of the Start pulses determines the integration time of the CCD image sensor.
Digital input signal for operating the circuit.
HCMOS compatible. Rising edge operation.
Digital output signal for indicating end-of-scan of the image sensor.
HCMOS compatible. Negative logic.
Analog ground
Analog ground
Analog power supply
Digital ground
Digital ground
Digital ground
Digital output signal for A/D conversion. HCMOS compatible. Positive logic.
Pin connections of "TE CONTROL I/O" connector (C7041)
9-pin D-sub connector
5
4
9
3
8
2
7
1
6
KACCC0075EA
Pin No.
1
2
Terminal name
VD2 (+5 V)
Temp monitor
3
Cooling control
4
Vp (+5 V)
5
6
7
VF (+12 V)
D.GND
D.GND
8
P.GND
9
F.GND
Description
Digital power supply
Analog output signal of the temperature of the CCD image sensor
Digital input signal for starting to cool down. HCMOS compatible.
High level or left open: cooling
Low level: stand-by
Power supply for the thermoelectric cooler in the CCD image sensor
(Please use AWG 18 wire)
Power supply for cooling fan
Ground
Ground
Power supply return of the thermoelectric cooler mounted in the CCD image sensor
(Please use AWG 18 wire)
Power supply return for cooling fan
Available for using same power supply (+5 V) for "+VD2" and "+Vp"
Caution: Do not connect "VD2" and "Vp" together on the backside of the 9-pin D-sub connector.
These may be connected (shorted) at the power supply end, not 9-pin D-sub connector.
7
CCD multichannel detector heads
C7040, C7041
Dimensional outlines (unit: mm)
C7040
0.5
0.3
34.0
2.7
Focal
plane
11.0
62.0
82.0
50.0
60.0
80.0
90.0
100.0
Focal
plane
50.0
(4 ) M3 depth 4
KACCA0062EC
35.0
C7041
34.0
2.4
0.5
Focal
plane
77.0
62.0
Focal
plane
11.0
82.0
50.0
60.0
80.0
90.0
100.0
50.0
(4 ) M3 depth 4
KACCA0063EC
8
CCD multichannel detector heads
C7040, C7041
Pin connections
TE controller
Power supply
Controller
VF (+12V)
F.GND
VP (+5V)
P.GND
VD2 (+5V)
D.GND
5
9
4
8
3
7
6
Cooling control
D.GND
2
1
I/O signal
Pulse generator
Power supply
CLK
D.GND
Start
D.GND
15
14
13
VD1 (+5V)
D.GND
VA1+ (+15V)
VA1- (-15V)
VA2 (+24V)
A.GND
Controller
Mode select
D.GND
S/H or A/D
Analog input
A.GND
S/H input
D.GND
Oscilloscope
CH1
GND
Ext.Trig
GND
12
11
10
9
8
7
6
5
4
3
2
1
KACCC0076EC
Multichannel detector head controller C7557-01
When connected to a HAMAMATSU multichannel detector head and a personal computer, the C7557-01 allows easy control of the detector head and data acquisition by using dedicated software that comes with the unit.
Suitable multichannel detector head
C7020/-02, C7021/-02, C7025/-02,
C7040, C7041, C7043, C7044, C7180,
C7181, C8061-01, C8062-01, C10150, C10151,
C5964 series, C8892
9
CCD multichannel detector heads
C7040, C7041
Accessories
· Spare fuse (2.5 A)*10
· AC cable
· 2 to 3 conversion adapter
· USB cable
· Detector head connection cables (for “SIGNAL I/O” and
“TE CONTROL I/O” terminal of multichannel detector head)
· CD-R (MCD USB driver, software, operation manual)
· MOS adapter*11
*10: Contained in the holder just above the AC cable connector on the C7557-01 rear panel.
*11: When operating the NMOS multichannel detector head, always be sure to attach the MOS adapter (supplied) to the C7557-01 main
unit. If the the NMOS multichannel detector head is connected and the power is turned on without attaching the adapter, the power
supply in the C7557-01 main unit may be damaged.
MOS ŢťŢűŵŦų
MOS adapter mounting example
Connection example
Shutter *
timing pulse
AC cable (100 to 240 V; included with the C7557-01)
Trig.
POWER
Dedicated cable
(Included with the C7557-01)
SIGNAL I/O
USB cable
(Included with
the C7557-01)
TE CONTROL I/O
Image sensor
+
Multichannel
detector head
C7557-01
PC (Windows 2000/XP/Vista)
(USB 2.0)
KACCC0402EA
10
CCD multichannel detector heads
C7040, C7041
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Disclaimer
Information described in this material is current as of December, 2015.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866
Cat. No. KACC1034E15 Dec. 2015 DN
11