AS1324 - Evaluation Board Application Note AS1324 Evaluation Board Application Note www.austriamicrosystems.com Revision 1.00 1-4 AS1324 - Evaluation Board Application Note General Description Board Description F E A C D H I B B G Figure 1: Board Description - Connectors Figure 2: Board Description – Measurement Points Connector Description Label Name Description Info A B C Vin GND EN Power Supply Connectors for Vin and Ground. Active-High Enable Input Connector 1 D On / Off EN Enable Jumper E Vout Power Output Connector +2.7V to +5.5V 1/ON = The AS1324 is on. 0/OFF = The AS1324 is off and the current into Vin is ≤5µA (typ). Fixed Output Voltage of 1.8V Measurement Points Description Label Jumper Description Info F G H I Vin GND Vout EN Power Supply Connectors for Vin and Ground. Power Output Connector for Vout Active-High Enable Connector Measurement Points Operational sequence This evaluation board comes with the AS1324 soldered on. The output voltage is set to 1.8V. For more information which other output voltages are available please see the ordering information in the datasheet. 1. If not present get the datasheet for the AS1324 from www.austriamicrosystems.com. Drive the IC on the Evaluation board only with the recommended settings and values as described in the datasheet. 2. Connect a +2.7V to +5.5V power supply (Vin “A” and GND “B”). 3. Perform measurements at the measurement points. If there are questions do not hesitate to contact us. See contact information at the end of the application note. 1 If the EN Input Connector C is used, be sure that the EN jumper D is completely removed. Otherwise the supply source could be damage through a short circuit. www.austriamicrosystems.com Revision 1.00 2-4 AS1324 - Evaluation Board Application Note Layout of evaluation board Board schematics and layout Figure 3: Schematics Figure 4: Top view Figure 5: Bottom view Assembly List Label C1, C2 C3 L1 R1 R2 Info 16V 10µF 0805 X7R 10% 10V 22pF 0805 X7R 10% 4.7µH, 50mΩ, 1820mA 1MΩ 0805 1% 511kΩ 0805 1% www.austriamicrosystems.com Type GRM21BR71A106KE51 GRM216R71A220KE51 MOS6020-472MLC Revision 1.00 Manufacturer Murata Coilcraft 3-4 AS1324 - Evaluation Board Application Note Copyright Copyright © 1997-2009, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, AustriaEurope. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Diclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG A-8141 Schloss Premstätten, Austria T. +43 (0) 3136 500 0 F. +43 (0) 3136 5692 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact-us www.austriamicrosystems.com Revision 1.00 4-4