an1038

ISL5585XEVAL Evaluation Board User’s Guide
®
Application Note
September 2002
AN1038
Introduction
Getting Started
The ISL55185XEVAL1 board can be used to evaluate the new
ISL5585 3.3volt SLIC. This platform supports the evaluation of
the performance of the ISL5585 at 3.3 volts with a 5 volt
CODEC. The lab data presented in this application note had
the following supplies voltages: Vcc (ISL5585) = 3.3V,
Vcc (CODEC) = 5V, VBH = -100v and Vbl = -24v.
Your evaluation kit should contain application note AN1038
and the following hardware.
The ISL5585XEVAL1 evaluation board provides a complete
evaluation system for the ISL5585 family of ringing SLICs.
Included on the evaluation board is a single +5V CODEC for
line circuit evaluations and on board logic for stand alone
operation. The evaluation boards have been designed to
support back to back operation, providing further insight to
the complete signal path and solution.
The transient behavior of the ISL5585 in response to mode
changes has been improved. The benefit to the application
is reduction or more likely elimination of DET glitches when
off hook events occur.
Voltage ratings for external components have been selected
based on 100V device operation, therefore compatibility to
lower voltage versions is guaranteed.
1. One ISL5585XEVAL1evaluation board.
2. One ISL5585X device sample, already in board.
3. One PLCC extraction tool.
4. One cable assembly with multi colored conductors.
5. One cable assembly with solid white conductors.
The evaluation board should have the same appearance as
the silk screen shown in Figure 1.
Applying Power to the Evaluation Board
Here are a few safeguards with power sequencing until you
are accustomed to using the high voltages required by the
devices.
1. Limit the current on all power supplies to 100mA.
2. Turn on the power supplies after the power cables are
attached to the evaluation boards.
FIGURE 1. EVALUATION BOARD SILK SCREEN
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002. All Rights Reserved
RSLIC18™ is a trademark of Intersil Corporation.
Application Note 1038
Evaluation Board Functional Description
J5
J6
J10
J7
J9
J8
J4
J11
JP3
JP9
JP6
JP4
J3
JP7
CODEC
APP CKT
JP8
ISL5585
APP CKT
J12
J13
JP5
JP1
JP11
JP12
J2
JP2
J14
JP10
J1
S1 S2 S3
S4 S5
CLOCK GENERATION & MUX
S6
J15
FIGURE 2. EVALUATION BOARD FUNCTIONAL DIAGRAM
Evaluation Board Jumper Definitions
JUMPER
DESCRIPTION
JP1
Connects SW- directly to the device Ring terminal of device. Used in conjunction with external load D TA and RTA .
JP2
Connects SW+ through test load to the Tip terminal of device. Used in conjunction with external load DTA and RTA .
JP3
Not used. Leave open.
JP4
Connects the receive output of the CODEC (U6) to the device receive input -IN. Path is AC coupled with C IN .
JP5
Position1, CODEC: Connects the CODEC receive output to the device ringing input. Path is AC coupled by CRS .
Position 2, EXT: Connects the VRS connector J9 to the device ringing input. Path is AC coupled by C RS .
Position 3 TRAP: Connects the VRS connector J9 thru RC network to the device ringing input. Path is AC coupled.
JP6
Connects the device transmit output VTX to the CODEC amplifier for transhybrid balance. Path is AC coupled by CTX .
JP7
Connects the receive output of CODEC to transhybrid amplifier, AC coupled by C1. Normally inserted for proper operation.
JP8
Inserting jumper sets the CODEC to A-law coding. Open sets the CODEC to µ-law coding.
JP9
Inserting jumper powers down the CODEC. Open provides normal CODEC operation.
JP10
Position 1: Sets the CODEC master clock to 2.048MHz.
Position 2: Sets the CODEC master clock to 512kHz
Position 3: Sets the CODEC master clock to 256kHz.
JP11
Enables the on board logic multiplexer. Should be installed for single board or back to back evaluations. Remove when driving
BNCs J10 thru J13.
JP12
Inserting jumper selects on board clock and frame sync generator. Insert to configure board as master for back to back
evaluations or for single board evaluations. Remove to configure board as slave for back to back evaluations.
2
Application Note 1038
Test Points
TABLE 1. ISL5585 OPERATING MODES
Each connector interface to the evaluation board has a test
point. All test points are DC coupled and should be guarded
against ground shorts. High impedance test inputs, such as
oscilloscopes or DVMs, should be used to monitor these
points. Unused BNC connections also provide convenient
test point access.
OPERATING MODE
Toggle Switches
The six toggle switches, S1 thru S6, interface directly to the
ISL5585 device. Positioning any switch towards the top of
the board is a logic “1”. Positioning any switch towards the
bottom of the board is a logic “0”. All switches are labeled
with the control signal names.
F2
F1
F0
Low Power Standby
0
0
0
Forward Active
0
0
1
Unused
0
1
0
Reverse Active
0
1
1
Ringing
1
0
0
Forward Loop Back (Note)
1
0
1
Tip Open
1
1
0
Power Denial
1
1
1
NOTE: The ISL5585 device should always operate from low battery
voltage when using the Forward Loop Back mode.
The switch E0 selects the switch hook (E0 = 1) or the ground
key detector (E0 = 0) to appear at DET. During ringing, the
device overrides E0 and sends the ring trip detector to DET.
The switched labeled SWC turns on the uncommitted switch
when set to a logic low. The battery select signal BSEL,
selects the high battery when set to logic high. The operating
modes for the ISL5585 device are provided in Table 1.
Refer to the device electrical data sheet for detailed
descriptions regarding each operating mode according to
the device under evaluation.
Evaluation Board Connector Descriptions
CONNECTOR
DESCRIPTION
J1
RJ11 type phone connector.
J2
Ring terminal of board.
J3
Tip terminal of board.
J4
Grounding lug connected to board ground plane.
J5
1: VCC. Positive 5V supply to CODEC U6, clock generator U5 and logic devices U2 thru U4 (red wire).
2: VBH. High negative battery supply to the ISL5585 device (orange wire).
3: VBL. Low negative battery supply to the ISL5585 device (yellow wire).
4: +5V. Positive 5V supply to the ISL5585 device and LEDs (green wire).
7 thru 10: GND. Twisted pair returns for external supply connections (black wires).
J6
Identical pinout as J5. Either connector provides daisy chain connection to second board for back to back evaluation.
J7
Transmit analog output from ISL5585 device, VTX. This path is AC coupled by CTX .
J8
Receive analog input to ISL5585 device, VREC. This path is AC coupled by CIN .
J9
Ringing input to ISL5585 device, VRS. This path is AC coupled by C RS.
J10
Serial transmit data output of CODEC U6.
J11
Serial receive data input to CODEC U6.
J12
Common frame sync input for receive and transmit digital data.
J13
Common clock for CODEC data transfer and conversion.
J14
20 pin, 100 mil spacing header with all digital PCM data interfaces to CODEC U6.
J15
20 pin, 100 mil spacing header with all digital interfaces to ISL5585 device.
3
Application Note 1038
Stand Alone Configuration
J5
J6
J10
J7
J9
J8
J4
J11
JP3
JP9
J3
JP6
JP4
ISL55855
APP CKT
JP8
JP7
CODEC
APP CKT
J12
JP5
JP1
JP11
JP12
J2
JP2
J14
JP10
J1
S1 S2 S3
S4
S5
S6
CLOCK GENERATION & MUX
J15
FIGURE 3. STAND ALONE CONNECTORS AND JUMPERS
Description
Status LEDs
The standalone configuration supports any measurement of
the ISL5585 device. With all the jumper locations open, the
device is totally isolated from all other active circuitry on the
evaluation board. All other circuitry is powered, but does not
interfere with proper SLIC operation.
The status LEDs DET and ALM are active for the stand
alone configuration. DET should only light when a DC
current path exists from Tip to Ring or during forward loop
back. ALM should only light during forward loop back
operation. Normal device evaluations should not cause the
ALM indicator to light.
Power Supply Connections
Power should be applied to the evaluation board using the
primary power cable. Either J5 or J6 may be used. Prior to
applying power, the voltage setting of each supply should be
verified. The power supplies should be turned off while
mating the primary power cable to the evaluation board.
Jumper Settings
All jumper positions should be open for the stand alone
configuration.
Uncommitted Switch Jumpers
When the jumpers JP1 and JP2 are installed, the
uncommitted switch is connected across Tip and Ring. The
test load of D TA and RTA will connect across the Tip and
Ring terminals when the uncommitted switch is turned on.
The DC load will result in DET transitioning to a logic low.
The circuit diagram is shown below.
TIP
Measurement Capability
JP2
Nearly all AC and DC parameters of the device can be
measured using this configuration. The device has been
socketed to allow easy measurements of more than a single
device. An extraction tool has been included with the
evaluation kit and should be used to remove the device from
the socket. The typical device measurements are listed below.
1. Power supply current per operating mode.
2. Tip and Ring DC voltages per operating mode.
3. On hook AC gains G42 , G24 and G44 .
4. Off hook AC gains G42 , G24 and G44 .
5. Other AC parameters such as longitudinal balance.
4
RING
DTA
RTA
JP1
SW+
SW-
SWC
FIGURE 4. TEST LOAD SWITCHING
Socket Removal
The surface mount socket for the ISL5585 device has the
same solder foot print as the PLCC package. Therefore, the
socket may be removed for more extensive characterization.
Application Note 1038
Stand Alone Configuration Typical Measurements
Supply Currents (milli amps) - On Hook
F2, F1, F0
E0
SWC
BSEL
ICC
(Vcc= 3.3v)
IBH
(Vbh= -100v)
IBL
(Vbl = -24v)
Low Power Standby
0, 0, 0
x
1
1
2.9
0.6
0.3
Forward Active
0, 0, 1
x
1
0
3.7
0
1.2
Unused
0, 1, 0
n/a
n/a
n/a
n/a
n/a
n/a
Reverse Active
0, 1, 1
x
1
0
3.7
0
1.2
Ringing
1, 0, 0
x
1
1
5.6
1.5
0.7
Forward Loop Back
1, 0, 1
x
1
0
11.9
0
20
Tip Open
1, 1, 0
x
1
1
2.9
0.6
0.3
Power Denial
1, 1, 1
x
1
x
3.3
0
0.2
OPERATING MODE
Tip and Ring Voltages (Volts) - On Hook
OPERATING MODE
F2, F1, F0
E0
SWC
BSEL
TIP
RING
Low Power Standby
0, 0, 0
x
1
1
-0.7
-52
Forward Active
0, 0, 1
x
1
0
-3.9
-17
Unused
0, 1, 0
n/a
n/a
n/a
n/a
n/a
Reverse Active
0, 1, 1
x
1
0
-17
-3.9
Ringing
1, 0, 0
x
1
1
-50
-50
Forward Loop Back
1, 0, 1
x
1
0
-3.9
-17
Tip Open
1, 1, 0
x
1
1
Float
-52
Power Denial
1, 1, 1
x
1
x
Float
Float
AC Gains (dB), Off Hook, 600Ω Termination - Forward and Reverse Active Only
OPERATING MODE
F2, F1, F0
E0
SWC
BSEL
G42
G24
G44
Forward Active
0, 0, 1
x
1
0
0.0
-7.3
-7.3
Reverse Active
0, 1, 1
x
1
0
0.0
-7.3
-7.3
AC Gain Equations
G42
RS
V 2W
ZL
ZL
 RS 
G 4-2 = ------------ = 2  ---------- ---------------------------------------- = 2 -------------------- = ---------V IN
R
Z
+
Z
+
2
Z
+
Z
R
 I N L
O
RP
L
L
IN
G24
ZO


G 24 = –  ---------------------------------------
 Z O + 2R P + Z L 
G44
ZO
 RS  

= –  ----------  ---------------------------------------
G 44 = G 42 × G
24
R
Z
+
2R
+
Z
 IN  L
P
O
5
Application Note 1038
Ringing Configuration
J5
J6
J10
J7
J9
J8
J4
J11
JP3
JP9
JP6
JP4
J3
ISL5585
APP CKT
JP8
JP7
CODEC
APP CKT
J12
J13
JP5
JP1
JP11
JP12
J2
JP2
J14
JP10
J1
S1
S2
S3
S4
S5
S6
1
0
0
x
1
1
CLOCK GENERATION & MUX
J15
FIGURE 5. RINGING CONNECTORS AND JUMPERS
Description
The ringing configuration supports full evaluation of the
ringing capability of the ISL5585 device. The evaluation
board design does not include a 20Hz digital code
generator, therefore, all ringing waveforms will be sourced
by external test equipment.
Power Supply Connections
Power should be applied to the evaluation board using the
primary power cable. Either J5 or J6 may be used. Prior to
applying power, the voltage setting of each supply should be
verified. The power supplies should be turned off while
mating the primary power cable to the evaluation board.
Jumper Settings
The jumper JP5 provides three positions for different ringing
techniques.
TABLE 2. JP5 JUMPER POSITIONS
JP5 POSN
CODEC
DESCRIPTION
Connects the CODEC receive output to the device
ringing input. Signal path is AC coupled.
EXT
Connects the VRS connector J9 to the device ringing
input. Signal path is AC coupled.
TRAP
Connects the VRS connector J9 thru RC network to
the device ringing input. Signal path is AC coupled.
CODEC Ringing
Most test equipment designed to evaluate the CODEC PCM
interface are capable of output frequencies as low as 20Hz.
If such a piece of equipment is available, then CODEC
6
ringing can be evaluated. The digital interface to the CODEC
would be provided by the BNC connectors J10 thru J13.
Verify JP11 is open prior to driving signals into the BNC
connectors. An output level of 0dBm from the CODEC will
provide full scale ringing when operating from -100V battery.
External Ringing Source
Using an external function generator at J9 provides the most
control of the ringing waveform. The flexibility of the ringing
interface can be fully exercised by the function generator. To
evaluate DC offsets during ringing, the capacitor C RS must
be shorted. Most functions generators provide DC offset as
part of the output waveform. Positive DC offsets on VRS
move Tip towards ground and Ring towards battery.
Trapezoidal Ringing
A logic level square wave, at J9, with 50% duty cycle will be
shaped by the components RTRAP and CTRAP when this
jumper position is selected. The components shipped with
the evaluation board will result in a 75VRMS trapezoidal
ringing waveform when operating from a -100V battery.
Ring Trip Control
Three very distinct actions occur when the devices detects a
ring trip. First, the DET output is latched low. The latching
mechanism eliminates the need for software filtering of the
detector output. The latch is cleared when the operating
mode is changed externally. Second, the VRS input is
disabled, removing the ring signal from the line. Third, the
device is internally forced to the forward active mode. The
low battery is not automatically selected upon ring trip.
Application Note 1038
Digital Loop Back Configuration
J5
J6
J10
J7
J8
J9
J4
J11
JP3
JP9
JP6
JP4
J3
ISL5585
APP CKT
JP8
JP7
CODEC
APP CKT
J12
J13
JP5
JP1
JP11
JP12
J2
JP2
J14
JP10
J1
S1
S2
S3
S4
S5
S6
0
0
1
x
1
0
CLOCK GENERATION & MUX
J15
FIGURE 6. DIGITAL LOOP BACK CONNECTORS AND JUMPERS
Description
Signal Flow
The digital loop back configuration verifies the interface and
operation of the ISL5585 device and the CODEC. This
configuration provides a self test to verify proper operation of
the board. In addition, it provides a complete digital loop,
allowing analog control of the digital input and output of the
CODEC. Forward active and reverse active or teletax will
support the digital loop back configuration.
Driving a signal at VREC, J8, will result in a signal from the
CODEC receive output when the ISL5585 device is
terminated at Tip and Ring. The following diagram shows the
signal path formed by the jumpers and terminated SLIC.
VREC (J8)
RIN
TIP
Power Supply Connections
Power should be applied to the evaluation board using the
primary power cable. Either J5 or J6 may be used. Prior to
applying power, the voltage setting of each supply should be
verified. The power supplies should be turned off while
mating the primary power cable to the evaluation board.
Jumper Settings
TABLE 3. DIGITAL LOOP BACK JUMPER POSITIONS
JP6
PO-
-IN
DR
600Ω
J14
VTX
RING
ISL5585
-2
JP6
TG
DT
CODEC
FIGURE 7. DIGITAL LOOP BACK SIGNAL FLOW
All jumper settings and functions are described below.
JUMPER
JP4
DESCRIPTION
Connects the device transmit output VTX to the
CODEC amplifier for transhybrid balance.
JP10, POSN 2 Sets the CODEC master clock to 512kHz.
JP11
Enables the on board logic multiplexer.
JP12
Inserting jumper selects on board clock and frame
sync generator.
J14, POSN 1
Connects the CODEC digital output DT to digital
input DR.
7
With VREC input signal level of 0.775VRMS , a signal level of
0.337VRMS should result at the VTX output when terminated
with 600Ω. The signal level at VTX is determined by the
4-wire to 4-wire gain, G44 , of the ISL5585. The transhybrid
balance is not connected, therefore, the digitized signal level
at the CODEC will be approximately 0.674VRMS . The
CODEC transfer functions are set for unity gain, therefore
the signal level at PO- should be approximately 0.674VRMS .
The signal levels for digital loop back are independent of the
clock selected by JP10.
Refer to the device electrical data sheet for the design
equations for the 4-wire to 4-wire gain as a function of
termination and synthesized impedance.
Application Note 1038
PCM4 Configuration
J5
J6
J10
J7
J9
J8
J4
J11
JP3
JP9
JP6
JP4
J3
ISL5585
APP CKT
JP8
JP7
CODEC
APP CKT
J12
J13
JP5
JP1
JP11
JP12
J2
JP2
J14
JP10
J1
S1
S2
S3
S4
S5
S6
0
0
1
x
1
0
CLOCK GENERATION & MUX
J15
FIGURE 8. PCM4 CONNECTORS AND JUMPERS
Description
Clock and Frame Sync
The PCM4 configuration verifies the AC transmission of the
ISL5585 and CODEC. Any piece of test equipment capable
of PCM testing with digital and analog interfaces can be
used in this configuration.
The clock and frame sync signals are driven at connectors
J13 and J12 respectively. The clock input is common to the
MCLK, BCLKT and BCLKR of the CODEC. The frame sync
input is common to the receive and transmit frame syncs,
FSR and FST, of the CODEC. These connections define
synchronous mode of operation.
Power Supply Connections
Power should be applied to the evaluation board using the
primary power cable. Either J5 or J6 may be used. Prior to
applying power, the voltage setting of each supply should be
verified. The power supplies should be turned off while
mating the primary power cable to the evaluation board.
Jumper Settings
All jumper settings are described below.
TABLE 4. PCM4 JUMPER POSITIONS
JUMPER
DESCRIPTION
JP4
Connects the receive output of the CODEC (U6) to
the device receive input -IN through RIN. Signal
path is AC coupled.
JP6
Connects the device transmit output VTX to the
CODEC amplifier for transhybrid balance. Signal
path is AC coupled.
JP7
Connects the receive output of CODEC to
transhybrid amplifier, AC coupled by C1.
JP8
Inserting jumper set the CODEC to A-law coding.
Open sets the CODEC to µ-law coding. This must
match PCM test equipment coding scheme for
proper operation.
8
Digital to Analog
The receive signal path is defined from the CODEC PCM
input to the ISL5585 Tip and Ring outputs. The PCM4 tester is
capable of driving digital test signals on the PCM bus and
measuring the resultant signal at Tip and Ring. With this type
of capability, the full receive path can be evaluated. Typical
performance measurements include overall loss, gain
variation versus frequency, gain versus signal level and 2-wire
return loss. In addition fidelity measurements such as idle
channel noise and distortion are also performed.
Analog to Digital
The transmit signal path is defined from ISL5585 Tip and
Ring interface to the CODEC PCM output. The same tests
performed for the receive path also apply to the transmit
path.
Digital to Digital
The digital to digital path is from the CODEC PCM input to
the CODEC PCM output. This signal path provides a
measure of the transhybrid balance for the line circuit. Most
other AC performance metrics are base on analog to digital
or digital to analog measurements. For proper transhybrid
measurements, verify jumper JP7 is inserted.
Application Note 1038
PCM4 Configuration Typical Measurements
MODE A 33 VAR. GAIN/FRE. TX:
+1.5
RX: -0.dBr
A-A
MODE A 33 VAR. GAIN/FRE. TX:
+1.5
RX:
RX
TS +1.0
TS
A-D
D-A
+0.0
RESULT
D-D
dB
-1.5
200
TS 0
TX:
FREQ.
1000
+0.00 dBm0
2000
3000
201Hz
3600
∆ =100Hz
FIGURE 9. DIGITAL TO ANALOG GAIN vs FREQUENCY
MODE A 43 VAR. GAIN/LEV. TX:
+2.0
RX: -0.0dBr
MODIF.
A-A
D-A
RESULT
+0.0
D-A
+0.0
D-D
SWP/S
1000
+0.00 dBm0
2000
201Hz
3000
FREQ.
3600
∆ = 100Hz
FIGURE 10. ANALOG TO DIGITAL GAIN vs FREQUENCY
MODE A 43 VAR. GAIN/LEV. TX:
+2.0
+0.0 RX:
dBr
MODIF.
RX:
TS
0
RESULT
A-A
A-D
+1.0
D-A
+0.0
dB
D-D
dB
A-D
-1.5
200
TX: TS
0
A-D
+1.0
0
+1.0
-1.0
RX:
TS
A-A
dB
SWP/S
-1.0
dBr
0
0
RESULT
+0.0 RX:
D-D
-1.0
-1.0
SWP/S
-2.0
-55.0
TX: TS
0
-40.0
-55.0 0dBM0
-20.0
1014Hz
LEVEL
+0.0
∆ = 2.0dB
SWP/S
TX:
FIGURE 11. DIGITAL TO ANALOG GAIN vs LEVEL
MODE A 55 TOTAL DIST.
+44.0
TX:
MODE A 55 TOTAL DIST.
+44.0
A-A
LEVEL
+0.0
∆ = 2.0dB
TX: +0.0 RX:
dBr
A-A
RX: +40.0
TS
A-D
0
D-A
RESULT+30.0
dB
RESULT +30.0
D-A
dB
D-D
+20.0
SWP/S
+14.0
-55.0
-40.0
TS
0 -55.0 0dBm0
-20.0
1014Hz
LEVEL
+0.0
∆ = 2.0dB
FIGURE 13. DIGITAL TO ANALOG TOTAL DISTORTION
9
A-D
0
D-D
+20.0
TX:
-20.0
1014Hz
FIGURE 12. ANALOG TO DIGITAL GAIN vs LEVEL
RX: 0.0dBr
RX:+40.0
TS
-2.0
-55.0
-40.0
TS
0
-55.0 0dBm0
TX:
+14.0
-55.0
-40.0
TS
0 -55.0 0dBm0
SWP/S
-20.0
1014Hz
LEVEL
+0.0
∆ = 2.0dB
FIGURE 14. ANALOG TO DIGITAL TOTAL DISTORTION
Application Note 1038
Back to Back Configuration
MASTER
0
0
0
1
x
1
1
x
1
0
0
0
SLAVE
SECONDARY POWER CABLE
FIGURE 15. BACK TO BACK CONNECTORS AND JUMPERS
Description
TABLE 6. SLAVE BOARD JUMPER POSITIONS
The back to back configuration connects two evaluation
boards together at the PCM interface. The PCM output data
from one board is the PCM input data to the other board.
One board is configured as a master for clock generation
and the other is configured as a slave. A secondary power
cable provides daisy chain power to the second evaluation
board.
Power Supply Connections
Power should be applied to the evaluation board using the
primary power cable. Either J5 or J6 may be used. Prior to
applying power, the voltage setting of each supply should be
verified. The power supplies should be turned off while
mating the power cables to the evaluation boards.
Jumper Settings
All jumper settings are described below.
TABLE 5. MASTER BOARD JUMPER POSITIONS
JUMPER
DESCRIPTION
JP4
Connects the receive output of the CODEC (U6) to
the device receive input -IN through RIN.
JP6
Connects the device transmit output VTX to the
CODEC amplifier for transhybrid balance.
JP7
Connects the receive output of CODEC to
transhybrid amplifier, AC coupled by C1.
JP10, POSN 2 Sets the CODEC master clock to 512kHz.
JP11
Enables the on board logic multiplexer.
JP12
Configures board as master.
10
JUMPER
DESCRIPTION
JP4
Connects the receive output of the CODEC (U6) to
the device receive input -IN through RIN.
JP6
Connects the device transmit output VTX to the
CODEC amplifier for transhybrid balance.
JP7
Connects the receive output of CODEC to
transhybrid amplifier, AC coupled by C1.
JP11
Enables the on board logic multiplexer.
In this configuration the master board provides the clock and
frame sync to the slave board. The selection of the clock rate
is arbitrary and may be any of the available frequencies.
The ribbon cable used to connect the two boards at J14 also
connects the ground planes of the two evaluation boards.
Having returns adjacent to the high speed clock edges is
critical to reducing board level noise.
If transmission quality is poor verify both master and slave
boards are set up for same coding scheme, JP8. In addition,
verify the transhybrid jumper, JP7, is inserted in both boards.
If signal quality still does not improve, verify JP12 of the
slave board is not populated.
Analog to Analog Verification
The back to back configuration verifies the complete signal
path of two evaluation boards. Full duplex transmission is
provided from one Tip and Ring interface to the other. Both
ISL5585 devices do not have to be in the same transmission
mode (forward, reverse or teletax) for proper back to back
operation.
Application Note 1038
CPS1
CPS2
D1
CPS3
VCC
VBL
VBH
AUX
RP1
U1
TIP
VRS
CRS
CTX
ISL5585
RP2
RING
VTX
RS
SW+
CRT
RRT
-IN
SW-
CIN
CFB
VFB
RT
RSH
SWC
SH
BSEL
E0
RIL
ILIM
F0
F1
CDC
VCC
RIN
CDC
F2
CPOL
DET
POL
ALM
TL
RTL
AGND
BGND
FIGURE 16. ISL5585 BASIC APPLICATION CIRCUIT
Basic Application Circuit Component List
COMPONENT
VALUE
TOLERANCE
RATING
COMPONENT
VALUE
TOLERANCE
RATING
C DC, CFB
4.7µF
20%
10V
U1 - Ringing SLIC
ISL5585
N/A
N/A
R RT
20kΩ
1%
0.1W
C PS1
0.1µF
20%
>100V
R SH
49.9kΩ
1%
0.1W
C PS2 , CPS3
0.1µF
20%
100V
R IL
71.5kΩ
1%
0.1W
D1
1N400X type with breakdown > 100V.
RS
66.5kΩ
1%
0.1W
R TL
17.8kΩ
1%
0.1W
R P1, RP2 = 50Ω ,
0.5W,
matched to 0.1Ω.
C IN , CRS , C TX , CRT ,
C POL
0.47µF
20%
10V
Protection resistor values are application
dependent and will be determined by
protection requirements. Standard
applications will use ≥ 50Ω per side.
Design Parameters: Ring Trip Threshold = 90mAPEAK. Switch Hook Threshold = 12mA, Loop Current Limit = 24.6mA, Transient current limit:
ISOURCE = 100mA, ISINK = 120mA, Synthesize Device Impedance = 66.5KΩ /133.3 = 500Ω, with 51Ω protection resistors, impedance across Tip
and Ring terminals = 603Ω.
11
TIP
RING
J5
J5
J5
J5
J5
J5
J5
J5
J5
J5
J4
J1
J5
TIP
J2
RING
J6
J6
J6
5
6
7
8
9
10
J6
J6
J6
J6
4
J6
2
3
J6
5
6
7
8
9
10
4
3
2
1
+5V
R14
VCC
R2
R1
R15
+
BSEL
+5V
CRT
J6
1
F2
-
F1
CR2
CR1
+5V
+
RIL
+5V
F2
F0
17
4
19
AUX
18
VRS
20
VTX
22
-IN
21
VFB
7
SWC
1
E0
10
F0
9
F1
8
F2
16
NC
15
BSEL
12
DET
ALM 13
DET
ALM
SWC
E0
14
2
AGND BGND
CDC
POL
TL
25
TD
27
SH
26
ILIM
RTA 5
SW+
6
SW-
24
3
+5V VBLVBH
23
RIN
CR3 CIN
VBH
CPS5
JP3
VBL
DTA 1
TIP
28
RING
JP2
CPS4
JP1
CR4
CPS1
CPS2
CPS3
+5V
CDC
2
1
2
RRT
S6
3
2
CPOL
S3
ISL5585
S4
RSH
S1
3
1
S2
3
1
RTL
2
3
1
2
S5
3
1
2
3
1
RP
CP
2
4
6
8
10
12
14
16
18
20
ALM 1
DET 3
BSEL 5
7
F2 9
F1 11
F0 13
15
E0 17
SWC 19
J15
X0-43B
4
5
14
11
VCC
4
5
14
11
VCC
CTRAP
VAG
R4
R3
R9
R8
R7
R6
R5
20
19
18
17
5
4
3
2
1
TI+
VAC
TI-
TC
P0+
P0-
P1
R0-
R0+
0.1µF
C2
15
JP8
A-LAW
VSS _PCI
0R
DT
U6
FSR
MC145484
FST
BCLKR
BCLKT
MCLK
µ/A
VDD
6
VCC
10
13
7
14
9
12
11
16
8
9
P0 P1 P2 P3
Q0
PL
Q1
Q2
CP
Q3
U/D
TC
CE
RC
15 1 10
GND = 8, VCC = 16
7
12
13
3
2
6
C4
VCC
FS_CNT
C5
C6
1
411
S
311
410
310
U4
R11
R10
110
111
210
211
JP12
MASTER
JP9
PD
JP10
15 1 10 9
2.048MHz 1 2
P0 P1 P2 P3 3
512kHz 3 4
PL
Q0
2
2
256kHz 5 6
Q1
3
6
CP
Q2
5
7
DR_IN
Q3
6
U/D
12
TC
11
13
CE
RC
CLK_IN 10
GND = 8, VCC = 16
14
FS_IN 13
VRS
JP7
2 CODEC
THB
4 EXT
6 TRAP
RTRAP
C1
14 VCC OUT 8
U5
7
GND
CFB
VCC
1
3
5
JP4
CODEC
VXMIT
J7
RS
CTX
CRS
VREC
J8
U2
74HC191M
U2
74HC191M
12
4Y
3Y
2Y
1Y
R13
VCC
J13
J12
J10
J11
J14
2 DR_IN
1
4
3
FS_OUT 5
6
8
7
CLK_OUT 9
10
11 12 CLK_IN
13 14
15 16 FS_IN
17 18
19 20 DR_N
DT_OUT
JP11
B2B
15
R12
12 FS_OUT
9 CLK_OUT
7
4 DT_OUT
VCC
CLK
FS
DT
DR
OE
74HC257M
Evaluation Board Schematic
Application Note 1038
Application Note 1038
ISL5585XEVAL1 Electrical Component List
COMPONENT
VALUE
TOLERANCE
RATING
COMPONENT
VALUE
TOLERANCE
RATING
U 1 - Ringing SLIC
HC5518x
N/A
N/A
R 3, R7
100kΩ
1%
0.10W
U 2, U 3
74HC191M
N/A
N/A
R5, R6, R8, R9,
R10, R11, R12,
R13
10kΩ
1%
0.10W
U4
74HC257M
N/A
N/A
R14, R15
51Ω
5%, picked to
0.1Ω
0.50W
U5
XO-43B
N/A
N/A
CRT, C IN, CRS,
CTX, C1, CPOL,
CTRAP
0.47µF
20%
20V
U6
MC145484DW
N/A
N/A
CDC, CFB
4.7µF
20%
20V
R RT, RTRAP
20kΩ
1%
0.10W
CPS1, CPS2,
CPS3, CPS4,
CPS5
0.1µF
20%
100V
R SH
49.9kΩ
1%
0.10W
C2, C3, C4, C5, C6
0.1µF
20%
20V
R IL
71.5kΩ
1%
0.10W
CR3
DL4003CT-ND
N/A
N/A
R TA
100Ω
1%
0.25W
DTA
BAS21ZXCT
N/A
N/A
RS
66.5kΩ
1%
0.10W
CR1, CR2
LN1251C
N/A
N/A
RP
0Ω
1%
0.10W
R4
44.2kΩ
1%
0.10W
R 1, R 2
499Ω
1%
0.10W
RTL
17.8kΩ
1%
0.10W
R IN
66.5kΩ
1%
0.10W
ISL5585XEVAL1 Mechanical Component List
COMPONENT
VALUE
TOLERANCE
RATING
COMPONENT
VALUE
TOLERANCE
RATING
U 1- Socket
822271-1
N/A
N/A
J14, J15
10 Pin Header
N/A
N/A
U 6 Socket
IC51-0202-347
N/A
N/A
J2, J3, J4
39F893
N/A
N/A
N/A
N/A
N/A
N/A
J5, J6
43045-1000
N/A
N/A
JP5, JP10
3 Pin Header
J1
555165-1
N/A
N/A
JP1, JP2, JP3, JP4,
JP6, JP7, JP8, JP9,
JP11, JP12
1 Pin Header
J7, J8, J9, J10, J11,
J12, J13
CBJR20
N/A
N/A
S1, S2, S3, S4, S5,
S6
65F1681
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
13