LED Data Sheet - SECU190EC-S SECU190EC-S ● External Shape Type ： 3.0×1.4 Flat View LED ● Color ： Orange ● Lens color ： Clear ● Material of a chip ： AlGaInP ● Application ： Automotive, Consumer Electronics, Office Automation, Indicator ● Feature ： High Luminous Intensity, RoHS compliant, Compatible with heat-resistance of lead-free solder. ●Rating Symbol PD IF Ratings 75 30 Unit mW mA Remark Forward current reduction Pulse forward current ⊿IF -0.45 mA/℃ Avobe25℃ IFP 70 mA f=1kHz tw≦100μs Reverse voltage VR Topr Tstg 5 －30～ 85 －30～100 V ℃ ℃ Description Power dissipation Forward current Operating temperature Storage temperature ●Photoelectric characteristic (Ta=25℃) Description Forward voltage Reverse current Luminous intensity Dominant wavelength Spectral bandwidth Directional angle Symbol VF IR IV λd ⊿λ 2θ1/2 Conditions IF = 20mA VR = 5V IF = 20mA IF = 20mA IF = 20mA IF = 20mA Min Typ 2.0 60 130 590 15 120 Max 2.5 10 Unit V μA mcd nm nm deg. ●Luminous intensity rank (Ta=25℃) rank C D E F Luminous intensity range(mcd) 60 80 106 142 ～ ～ ～ ～ 120 160 214 ●Dominant wavelength rank (Ta=25℃) Tolerance：±2nm rank Dominant Wavelengs range(nm) Y 587 ～ 590 R 590 ～ 593 SANKEN ELECTRIC COMPANY, LTD. Page 1 / 10 LED Data Sheet - SECU190EC-S ●Characteristic data IF-VF 10 1 1.5 1.6 1.7 1.8 1.9 2.0 ＶＦ ［Ｖ］ 2.1 2.2 0.10 1 10 ＩＦ ［ｍＡ］ 100 Spectrum 1.1 1.0 30 Relative Intencity @IF=20mA 0.9 25 ＩＦmax [ｍＡ] 1.00 0.01 2.3 IFmax-Ta 35 IV-ＩF 10.00 ＩＶ（Relative intencity） ＩＦ [ｍＡ] 100 20 15 10 5 0 0 10 20 30 40 50 60 70 Ta ［℃］ 80 90 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 500 550 600 650 700 λ [nm] SANKEN ELECTRIC COMPANY, LTD. Page 2 / 10 LED Data Sheet - SECU190EC-S IV-Ta VF-Ta 2.5 2.4 2.5 2.3 VF [V] @IF=20mA IV [Relative intencity] @IF=20mA 3.0 2.0 1.5 1.0 0.5 2.2 2.1 2.0 1.9 1.8 1.7 0.0 1.6 -30 -10 10 30 50 Ta [℃] 70 90 -30 -10 10 30 50 Ta [℃] 70 90 Directional angle 0 -30 -60 -90 100% 30 60 90 100% SANKEN ELECTRIC COMPANY, LTD. Page 3 / 10 LED Data Sheet - SECU190EC-S ● Outline SEC*100E Series Outline dimensions Part in bulk (10/1) Cathode Cathode index 1.4 1.2 3.0 0.75 0.55 Resin Max 0.1 1.05 Anode Embossed taping (5/1) +0.1 ±0.05 2.0 4.0 φ1.5 -0 0.23 ±0.05 φ 1. 0 8.0 3.5 ±0.05 1.75 4.0 1.6 Cathode Direction of Feed Material & Finish of leads Material of resin Material Copper Material Finish Ag plating Silicone containing phosphor Tolerance ±0.2 SANKEN ELECTRIC COMPANY, LTD. Page 4 / 10 LED Data Sheet - SECU190EC-S ● Soldering conditions Following soldering conditions are recommended. ① Reflow conditions（at the surface of LED resin） Pre-heat ：150 ～ 180 ℃、60 ～ 120 sec Soldering temperature： Soldering time more than 220℃ is less than 40 sec. Peak temperature is should be is less than 260℃. Reflow soldering profile Temperature of surface LED [℃] 300 Peak Max 260℃ 260 220 180 Max 40 sec 140 Pre-heat 60 ～ 120 sec 100 60 20 0 50 100 150 200 250 300 Soldering Time ② Manual soldering Temperature of soldering iron tip should be 350±10℃ for 3 seconds, which shall apply to only one soldered point and once for the each soldered point. 4.2 1.2 1.2 ③ Recommendable soldering pattern Unit：mm SANKEN ELECTRIC COMPANY, LTD. Page 5 / 10 LED Data Sheet - SECU190EC-S ● Attention after opened The LED is in SMD package. When the LED is mounted by means of soldering and the resin is unusually damp, soldering may cause interfacial defoliation. This occurs when a drastic temperature change causes moisture in the resin to evaporate and to swell. Therefore, attention to the below must be paid. ① Atmosphere when using the LEDs after package is opened After opened and mounted, soldering should be carried out quickly. Following atmosphere is recommended when using (and mounting) the LEDs. Temperature : 5～30℃ Humidity : less than 70% ② Baking In case 168 hours have passed after package is opened, LEDs must be dried as follows. 60±5 ℃ for more than 24 hours (taping reel) ③ Storage after package is opened Following storage conditions are recommended after package is opened. In case indicator color (blue) of desiccant (ex. silica gel) has disappeared, LEDs must be dried under the same conditions as ② above. ● Other ① After soldering any mechanical force or excessive vibration should not be applied to LEDs during cooling process until the LEDs cool down to normal temperature. ② Quick cooling must be avoided. ③ The LEDs should not be mounted on warped direction of PCB. ④ This product series emits high light power. Do not look directly into the light emitting area. Direct exposure to the light over an extended time period may harm eyes. ⑤ Extra attention should be paid to the sealing resin of the product, which is silicone resin. ・The emitting area of the LEDs contains fine gold wires. Touching this area witout care may add excess stress on the internal gold wires and may result in ・The silver plating of the leadframe may discolor if the product comes into contact with material containing sulfides or if it is exposed to an atmosphere containing sulfide gas. SANKEN ELECTRIC COMPANY, LTD. Page 6 / 10 LED Data Sheet - SECU190EC-S ● Reliability test Test Items Life EIAJ ED-4701 Steady state operating life - Tests Test Conditions Ta=RT、Ifmax t=1000h High temperature storage 201 Ta=Tstgmax t=1000h Low temperature storage 202 Environ Ta=Tstgmin t=1000h -mental Moisture Resistance 103 Tests Ta=60±5℃、RH=90±5％ t=1000h Temperature cycle 105 Tstgmin(30min)～Tstgmax(30min) Soldering heat 301 T=260±5℃、t=10s、1time Solderaibirity 402 T=245±5℃、t=5±1s、1time、Using flux for Pb free solder 100cycles Drop - H=1m、Drop on maple board、10times Mesurement Item and Criterion Judge Failure No Measurement Item Mark Criterion Judge Failure 1 Forward Voltage VF OK≦V.F.S.×±20％ 2 Reverse Current IR OK≦U.S.L..×2.0 3 Luminous Intensity Iv OK≧I.V.S.×0.5 *Solderability … The Lead shall be covered by solder at least 95%. Mesurement conditions is based on specifications. Tstgmax and Tstgmin is absolute maximum ratings. IFmax and IFPmax is absolute maximum ratings. U.S.L. is upper limit of standard. V.F.S. is Initial data of VF. I.V.S. is Initial data of Luminous Intensity. SANKEN ELECTRIC COMPANY, LTD. Page 7 / 10 LED Data Sheet - SECU190EC-S ● Packing Packing Material ： Aluminum laminated moisture-proof packing Quantity ： 3000 pcs (Minimum order quantity) Label ： See below. Zipper Notch（Both sides） ＊Label 270±5 防湿梱包のご注意 印刷エリア １） ２） ３） P/N SEC****** LOT NO. **** QTY 3,000 PCS RANK *-* SANKEN ELECTRIC CO., LTD MADE IN JAPAN 230±5 ４） Unit：mm １) Part Number ： SEC＊＊＊＊＊＊ ２） Lot No． ： ＊ ＊ ＊＊ ↑ ↑ ↑ ① ② ③ ①Last digit of year、 ②Month (January～September→Arabic Numeral October →O、November→N、December→D) ③Day ３） quantity ： 3000pcs ４） Rank ： ＊－＊ ↑ ↑ ① ② ①Luminous intensity rank ②Dominant wavelength rank SANKEN ELECTRIC COMPANY, LTD. Page 8 / 10 LED Data Sheet - SECU190EC-S ● Taping reel dimensions +0 11.4±1.0 φ180 -3 9.0±0.3 Label P/N SEC***** LOT NO. **** QTY 3,000 PCS RANK *-* SANKEN ELECTRIC CO., LTD MADE IN JAPAN +1 φ60 -0 2.0 ±0.2 φ22 ±0.2 φ13 Tolerance ±0.2 ①Quantity The quantity per reel shall be 3000 pcs. ②Accumulative pitch tolerance Accumulative tolerance per 10 pitches shall be ±0.2mm. ③Adhesion strength of cover tape Adhesion strength shall be 0.1-0.7N when the cover tape and the carrier tape are torn off at the angle of 10 degrees. ④Packaging P/N, manufacturing date code number and quantity shall be indicated on a moist-proof package. SANKEN ELECTRIC COMPANY, LTD. Page 9 / 10 LED Data Sheet - SECU190EC-S ● Tips ・The contents written in this data sheet may be changed without a preliminary announcement by improvement etc. When you use it, please check that information is the newest and conclude specifications. ・Application and operation examples described in this publication are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. ・When using the products specified herein by either combining other products or materials therewith or physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. ・Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. ・Sanken products listed in this catalog are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment measuring equipment, etc.). Before placing an order, the user's written consent to the specifications is requested. When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), please contact your nearest Sanken sales representative to discuss and obtain written confirmation of your specifications. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. ・Anti radioactive ray design is not considered for the products listed herein. ・Gallium arsenic is used in some of the products listed in this document. These products are dangerous if they are burned or smashed in the process of disposal. It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed ・Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken’s distribution network. ・If there is any discrepancy between English and Japanese, the Japanese version should take precedence over the English one. SANKEN ELECTRIC COMPANY, LTD. Page 10 / 10