AX93291 Quick Installation Guide Jumper Settings Jumper Description JP1 COM1 Data/Power Selection Default: RS-232 Data Setting CN1 Pin 1: DCD 3-5 Close CN1 Pin 8: RI 4-6 Close COM1 Data/Power Selection (JP1) The COM1 port (CN1) has +5V level power capability on DCD and +12V level on RI by setting this jumper. Description Setting Power: Set CN1 pin 1 to +5V level Data: Set CN1 pin 1 to DCD (Default) Power: Set CN1 pin 8 to +12V level Data: Set CN1 pin 8 to RI (Default) 1-3 close 3-5 close 2-4 close 4-6 close Checklist I/O board x1 Quick installation guide x1 Screw pack x1 Com cable x2 Note: Please contact your local vendors if any damaged or missing items. DO NOT apply power to the module if there is any damaged component. Dimension and Fixing Holes Assembly Drawing Module Layout AX93291 Gently insert ZIO module into CPU board’s ZIO connector, see figure above. Align assembly holes and use screws to firmly secure ZIO module to CPU board. Be careful not to over-tighten the screws. 4 94193291000E ©Copyright 2015 Axiomtek Co., Ltd. Version A1 April 2015 Printed in Taiwan 94193291000E ©Copyright 2015 Axiomtek Co., Ltd. Version A1 April 2015 Printed in Taiwan 1 AX93291 ZIO Module Before applying power to AX93291, please make sure all jumper(s) are in factory default positions. ZIO Expansion Connector (CN5) The CN5 is for connecting ZIO expansion module to CPU board such as CAPA840. Connectors Connector Description CN1 CN2 CN3 CN4 CN5 COM1 Connector COM2 Connector Ethernet Port 1 Ethernet Port 2 ZIO Expansion Connector COM Connectors (CN1 and CN2) This module comes with two Molex 78046-1020, 2x5-pin p=2.00mm box headers; CN1 (for COM1) and CN2 (for COM2). Only CN1 is equipped with power capability on DCD and RI pins by setting JP1. Pin Signal Pin Signal 1 3 5 7 9 DCD RXD TXD DTR GND 2 4 6 8 10 DSR RTS CTS RI N.C. Ethernet Ports (CN3 and CN4) This module has two RJ-45 connectors: CN3 and CN4. Ethernet connection can be established by plugging one end of the Ethernet cable into this RJ45 connector and the other end (phone jack) to a 1000/100/10-Base-T hub. Pin Signal L1 L2 L3 L4 A MDI0+ L5 MDI2+ MDI0L6 MDI2MDI1+ L7 MDI3+ MDI1L8 MDI3Active LED (Yellow) 1000 LAN LED (Orange) / 100 LAN LED (Green) B 2 Pin Signal 94193291000E ©Copyright 2015 Axiomtek Co., Ltd. Version A1 April 2015 Printed in Taiwan Pin Signal Pin Signal A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 +12V +5VSB +5VSB +3.3VSB +3.3VSB RSVD RSVD SMB_CLK SMB_DATA GND PCI-E RXP4 PCI-E RXN4 RSVD RSVD RSVD No Use No Use GND No Use No Use PLTRST_N No Use No Use GND No Use No Use No Use No Use GND No Use B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 GND GND GND GND RSVD RSVD RSVD RSVD GND PCI-E TXP4 PCI-E TXN4 WAKE_N PCI-E CLKP PCI-E CLKN GND CLK_33M SERIRQ LAD0 LAD1 LAD2 LAD3 L_FRAME GND No Use No Use No Use No Use GND No Use No Use 94193291000E ©Copyright 2015 Axiomtek Co., Ltd. Version A1 April 2015 Printed in Taiwan 3