GOT3157W-881-PCT All-in-One 15.6” WXGA TFT Fanless Multi-Touch PANEL PC User’s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd. CAUTION If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturer’s instructions to only replace the same or equivalent type of battery, and dispose of used ones. Copyright 2015 Axiomtek Co., Ltd. All Rights Reserved May 2015, Version A1 Printed in Taiwan ii Safety Precautions Before getting started, read the following important cautions. 1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 2. Disconnect the power cords from the GOT3157W-881-PCT Series before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the GOT3157W-881-PCT Series is properly grounded. 3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body. When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. ® Windows is a trademark of Microsoft Corporation. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. ® ® Intel and Pentium are trademarks of Intel Corporation. AMI is trademark of American Megatrend Inc. Other brand names and trademarks are the properties and registered brands of their respective owners. iii Table of Contents Disclaimers ..................................................................................................... ii Safety Precautions ........................................................................................ iii Chapter 1 Introduction ............................................. 1 1.1 General Description ............................................................................ 1 1.2 Specifications ...................................................................................... 2 1.3 Dimensions and Outlines ................................................................... 4 1.4 I/O Outlets ............................................................................................ 5 1.5 Packing List ......................................................................................... 6 Chapter 2 Hardware and Installation ...................... 7 2.1 CFast card Installation ........................................................................ 8 2.2 Open back cover ................................................................................. 9 2.3 Jumper and COM port Connector .................................................... 10 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.3.7 2.3.8 2.3.9 2.3.10 2.3.11 2.4 CMOS Clear Jumper (SJP2 on SBC87881) .............................................. 11 Auto Power On Jumper (SJP4 on SBC87881) .......................................... 11 DC Power In Connector (SCN1) ............................................................... 12 HDMI Connector........................................................................................ 12 COM Serial Port Connector ...................................................................... 13 Ethernet Connector ................................................................................... 13 Serial ATA Connectors ............................................................................... 14 SIM Card Slots (SCN19) ........................................................................... 14 CFast™ Socket ......................................................................................... 15 Half-Size Express Mini Card Slot (SCN13) ............................................... 16 Full-Size Express Mini Card (w/ SIM Slot)/ mSATA (SCN14) ................... 17 Mountings: Panel / Wall / Desktop / VESA ...................................... 18 2.4.1 2.4.2 VESA/Wall-Mount ...................................................................................... 18 Panel-mount Kit Assembly ........................................................................ 19 2.5 HDD Installation................................................................................. 20 2.6 Installing CPU and PCH Thermal Pad .............................................. 22 2.7 DRAM Installation.............................................................................. 23 2.8 Wireless LAN Card Installation ........................................................ 24 2.9 Power Adapter Installation ............................................................... 26 Chapter 3 AMI BIOS Setup Utility .......................... 31 3.1 Starting ............................................................................................... 31 3.2 Navigation Keys ................................................................................ 31 iv 3.3 Main Menu.......................................................................................... 32 3.4 Advanced Menu ................................................................................. 33 3.5 Chipset Menu ..................................................................................... 43 3.6 Boot Menu.......................................................................................... 48 3.7 Security Menu .................................................................................... 49 3.8 Save & Exit Menu .............................................................................. 50 Chapter 4 Drivers Installation .............................. 53 4.1 Driver Disc content ........................................................................... 53 4.2 Touch Screen ..................................................................................... 54 v This page is intentionally left blank. vi GOT3157W-881-PCT User’s Manual Chapter 1 Introduction This chapter contains general information and detailed GOT3157W-881-PCT. Chapter 1 includes the following sections: General Description Specifications Dimensions and Outlets I/O Outlets Package List 1.1 specifications of the General Description th The GOT3157W-881-PCT adopts a 15.6-inch TFT LCD and supports LGA1150 Socket 4 generation Intel® Core™ i7/i5/i3/Celeron processor that can support Windows 7, Windows 7 Embedded, Windows 8, Windows 8 Embedded and variety applications. This fanless platform has below abilities make it surely a robust and cost-effective solution. Intel® Haswell H81 Platform Support LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processors. User can choose different processors for different applications. It also supports up to 8GB DDR3 1333/1600 MHz memory modules. There are rich I/O, such as dual PCIe mini card slot、2.5” HDD bay、USB3.0 port、RS232/422/485、HDMI output. This platform is a power-efficient solution. Reliable and Stable Design The GOT3157W-881-PCT is a fanless cooling system, which makes it suitable for vibration environments, such as the industrial machinery markets. For high capacity storage requirement, GOT3157W-881-PCT can work under 1.2G (5 ~ 500Hz, random for CFast card) in operation mode with a patent of anti-vibration design. The patent improves the system reliability and sustainability. Introduction 1 GOT3157W-881-PCT User’s Manual 15.6 inch WXGA TFT LCD with projected capacitive multi-touch 15.6 inch WXGA TFT LCD is with 300nits higher brightness and can displays contents in HD resolution. With projected capacitive multi-touch, users can operate more directly and friendly. The hardness of touch glass surface is up to 7h and is better for anti-scratch purpose. WLAN Antenna Supported (optional) GOT3157W-881-PCT has dual PCIe Mini Card slots for optional add-ons such as mSATA storage、wireless LAN card for 802.11 b/g/n connections or 3G/GPRS applications, and more. It also provides an optional fixed rotational WLAN antenna (optional) for wireless network connection. 1.2 Specifications Main CPU Board CPU Support LGA1150 socket for 4th Generation Intel® Core™ i Family Processors (TDP under 45W) System Chipset Intel○R H81 System Memory One 204-pin DDR3 SO-DIMM socket Maximum memory up to 8GB BIOS American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS I/O System Standard I/O 2 x RS-232/422/485 2 x USB 2.0, 2 x USB 3.0 Video I/O 1 x HDMI out Ethernet 2 x RJ45 for Giga Ethernet Audio 1 x Line-out 1 x Mic-in Expansion 2 x Mini-card slot (If you install 3G mini-card, you can’t use mSATA storage card) 2 x SATA 3 , 2 x SATA 2 Storage 1 x 2.5” HDD/SSD Bay 1 x CFast slot and mSATA Power connector 1 x 19V DC-IN power connector 2 Introduction GOT3157W-881-PCT User’s Manual System Specification 15.6 WXGA(1366x768) LCD with LED backlight & 400nits brightness Projected Capacitive Multi Touch Fanless Heat Dispensing Design IP65 front bezel Disk drive housing: 1x 2.5” SATA drive Net Weight 5.5Kg(12.1 lb) Dimension (Main Body Size) 396.8x247.1x90.4mm Operation Temperature 0℃ to 40℃ Relative Humidity 20% to 90% @ 40℃, Non-Condensing Power input 19V DC-IN power connector NOTE All specifications and images are subject to change without notice. NOTE If the operation temperature is higher than 40℃, the wide temperature card are recommended to be used on the device. NOTE If the operation temperature is higher than 45℃, the wide temperature DRAM is recommended to be used on the device. Introduction HDD/CF 3 GOT3157W-881-PCT User’s Manual 1.3 Dimensions and Outlines The following diagrams show the dimensions and outlines of GOT3157W-881-PCT Outline Dimension: 396.8x247.1x90.4 (mm) Cut out: 385.6x235.9mm 4 Introduction GOT3157W-881-PCT User’s Manual 1.4 I/O Outlets Please refer to the following illustration for I/O locations of the GOT3157W-881-PCT. 12 13 14 No Function No Function 1 POWER SWITCH (ATX) 8 2 x USB 2.0 2 Power Input connector 9 2 x USB 3.0 3 Audio Line-out 10 CFast card slot 4 Audio MIC-in 11 3 x Optional antennas (WiF/3G/GPS) 5 COM1/2 (RS-232/422/485) 12 LED Backlight On/off 6 HDMI output 13 Brightness + 7 Dual Gigabit Ethernet 14 Brightness - Introduction 5 GOT3157W-881-PCT User’s Manual 1.5 Packing List When you receive the GOT3157W-881-PCT, the bundled package should contain the following items: GOT3157W-881-PCT unit x 1 Driver Disc x1 Panel mount kit x 9 Screws for HDD x 4 SATA data cable x 1 SATA power cable x 1 CPU Thermal Pad x 2 If you can not find the package or any items are missing, please contact Axiomtek distributors immediately. 6 Introduction GOT3157W-881-PCT User’s Manual Chapter 2 Hardware and Installation The GOT3157W-881-PCT provides rich I/O ports and flexible expansions for you to meet different demand, for example CF card. The chapter will show you how to install the hardware. It includes: CFast Card Installation Open Back Cover Jumper & COM Port Connector Mounting Method Hard Disk Installation Installing CPU and PCH Thermal Pad DRAM Installation Wireless LAN Card Power Adapter Hardware and Installation 7 GOT3157W-881-PCT User’s Manual 2.1 CFast card Installation The GOT3157W-881-PCT provides one CFast card slot for users to install CFast card. Please refer to the following instructions for installation: Step 1 Open the cover, unscrew 2 screws on the chassis. Step 2 Install CFast card to the CFast card slot. Step 3 Insert the CFast card to the CFast card slot, then finding the CFast cover and screw it. 8 Hardware and Installation GOT3157W-881-PCT User’s Manual 2.2 Open back cover This section tells users how to open back cover. Please follow the steps below. Step 1 Unscrew 6 screws on the back cover. Please refer the drawing below. Step 2 Remove the back cover. Hardware and Installation 9 GOT3157W-881-PCT User’s Manual 2.3 Jumper and COM port Connector SBC87881 Top Side 10 Hardware and Installation GOT3157W-881-PCT User’s Manual Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following illustration shows how to set up jumper. Before applying power to GOT3157W-832-PCT, please make sure all of the jumpers and switch are in factory default position. Below you can find a summary table and onboard default settings. Jumper & Switch Setting CMOS Clear Jumper Section 2.3.1 External Connectors Section DC Power In Connector 2.3.2 HDMI Connector 2.3.3 COM Serial Port Connector 2.3.4 Ethernet Connector 2.3.5 Internal Connectors Section Serial ATA Connectors 2.3.6 SIM Card Slot 2.3.7 CFast™ Socket 2.3.8 Half-Size Mini Card Slot 2.3.9 Full-Size Mini Card w/ SIM Slot/ mSATA 2.3.10 2.3.1 CMOS Clear Jumper (SJP2 on SBC87881) Function Setting Normal (Default) 1-2 Clear RTC 2-3 2.3.2 Auto Power On Jumper (SJP4 on SBC87881) Function Setting No Auto Power on (Default) 1-2 open Auto Power On 1-2 with Jumper Clip Hardware and Installation 11 GOT3157W-881-PCT User’s Manual 2.3.3 DC Power In Connector (SCN1) The system supports a DC 19V power-din connector for system power input. Pin Signal 1 GND 2 GND 3 DC 19V 4 DC 19V 2.3.4 HDMI Connector The HDMI (High-Definition Multimedia Interface) is a compact digital interface which is capable of transmitting high-definition video and high-resolution audio over a single cable. Its interface is available through connector SCN6 or SCN7. Pin Signal Pin Signal 1 HDMI OUT_DATA2+ 11 GND 2 GND 12 HDMI OUT Clock- 3 HDMI OUT_DATA2- 13 N.C. 4 HDMI OUT_DATA1+ 14 N.C. 5 GND 15 HDMI OUT_SCL 6 HDMI OUT_DATA1- 16 HDMI OUT_SDA 7 HDMI OUT_DATA0+ 17 GND 8 GND 18 +5V 9 HDMI OUT_DATA0- 19 HDMI_HTPLG 10 HDMI OUT Clock+ 12 Hardware and Installation GOT3157W-881-PCT User’s Manual 2.3.5 COM Serial Port Connector The system has six serial ports. COM1/2 are RS-232/422/485 ports. Please refer to Chapter 3 for the detail of BIOS setting. Pin RS-232 RS-422 RS-485 1 DCD, Data Carrier Detect TX- Data- 2 RXD, Receive Data TX+ Data+ 3 TXD, Transmit Data RX+ No use 4 DTR, Data Terminal Ready RX- No use 5 GND, Ground No use No use 6 DSR, Data Set Ready No use No use 7 RTS, Request To Send No use No use 8 CTS, Clear To Send No use No use 9 RI, Ring Indicator No use No use 2.3.6 COM1/2 Ethernet Connector The RJ-45 connector is for Ethernet. To connect the board to a 1000/100/10 Base-T hub, just plug one end of the cable into connector and connect the other end (phone jack) to a 1000/100/10-Base-T hub. A B Pin Signal Pin Signal L1 MDI0+ L5 MDI2- L2 MDI0- L6 MDI1- L3 MDI1+ L7 MDI3+ A L4 MDI2+ L8 MDI3- B A Active LED (Yellow) B 100 LAN LED (Green)/ 1000 LAN LED (Orange) Hardware and Installation L8 L7 L6 L5 L4 L3 L2 L1 13 GOT3157W-881-PCT User’s Manual 2.3.7 Serial ATA Connectors These Serial Advanced Technology Attachment (Serial ATA or SATA) connectors are for high-speed SATA interfaces. They are computer bus interfaces for connecting to devices such as hard disk drives. Pin Signal 1 GND 2 SATA_TX+ 3 SATA_TX- 4 GND 5 SATA_RX- 6 SATA_RX+ 7 GND 2.3.8 SIM Card Slots (SCN19) GOT3157W-881-PCT includes one SIM slots on the bottom side of the system for inserting SIM Card. It is mainly used in 3G wireless network application. Pin 14 Signal 1 PWR 2 RST 3 CLK 4 NC 5 GND 6 VPP 7 I/O 8 NC Hardware and Installation GOT3157W-881-PCT User’s Manual 2.3.9 CFast™ Socket The system is equipped with a CFast™ socket on the top size of rear housing to support a CFast™ card which is based on the Serial ATA bus. The socket is specially designed to avoid incorrect installation of the CFast™ card. When installing or removing the CFast™ card, please make sure the system power is off. The CFast™ card by default identifies itself as C: or D: drive in your PC system. Pin Signal Pin Signal S1 GND PC1 NC S2 TX+ PC2 GND S3 TX- PC3 NC S4 GND PC4 NC S5 RX- PC5 NC S6 RX+ PC6 NC S7 GND PC7 GND PC8 NC PC9 NC PC10 NC PC11 NC PC12 NC PC13 3.3V PC14 3.3V PC15 GND PC16 GND PC17 NC Hardware and Installation 15 GOT3157W-881-PCT User’s Manual 2.3.10 Half-Size Express Mini Card Slot (SCN13) PCI Express Mini Card connector supports a PCI Express x1 link and a USB 2.0 link. A PCI Express Mini Card can be applied to either PCI Express or USB 2.0. It complies with PCI-Express Mini Card Spec. V1.2. Pin Signal Pin Signal 1 WAKE# 2 +3.3VSB 3 No use 4 GND 5 No use 6 +1.5V 7 CLKREQ# 8 No use 9 GND 10 No use 11 REFCLK- 12 No use 13 REFCLK+ 14 No use 15 GND 16 No use 17 No use 18 GND 19 No use 20 Pull High 21 GND 22 PERST# 23 PE_RXN3 24 +3.3VSB 25 PE_RXP3 26 GND 27 GND 28 +1.5V 29 GND 30 SMB_CLK 31 PE_TXN3 32 SMB_DATA 33 PE_TXP3 34 GND 35 GND 36 USB_D8- 37 GND 38 USB_D8+ 39 +3.3VSB 40 GND 41 +3.3VSB 42 No use 43 GND 44 No use 45 No use 46 No use 47 No use 48 +1.5V 49 No use 50 GND 51 No use 52 +3.3VSB 16 Hardware and Installation GOT3157W-881-PCT User’s Manual 2.3.11 Full-Size Express Mini Card (w/ SIM Slot)/ mSATA (SCN14) You may need to adjust the BIOS setting to select mSATA or Mini card PCI-E interface. This is a PCI-Express Mini Card connector which supports PCI-Express x1 link ,SATA link , USB 2.0 link and 3G wireless network application(SCN19). A PCI-Express Mini Card can be applied to either PCI-Express or USB 2.0 or SATA. It complies with PCI-Express Mini Card Spec. V1.2. Pin Signal Pin Signal 1 WAKE# 2 +3.3VSB 3 No use 4 GND 5 No use 6 +1.5V 7 CLKREQ# 8 9 GND 10 UIM_DATA 11 REFCLK- 12 UIM_CLK 13 REFCLK+ 14 UIM_RESET 15 GND 16 UIM_VPP 17 No use 18 GND 19 No use 20 Pull High 21 GND 22 PERST# 23 PE_RXN4/ SATA4_RXP 24 +3.3VSB 25 PE_RXP4/ SATA4_RXN 26 GND 27 GND 28 +1.5V 29 GND 30 SMB_CLK 31 PE_TXN4/ SATA4_TXN 32 SMB_DATA 33 PE_TXP4/ SATA4_TXP 34 GND 35 GND 36 USB #10_D- 37 GND 38 USB #10_D+ 39 +3.3VSB 40 GND 41 +3.3VSB 42 No use 43 GND 44 No use 45 No use 46 No use 47 No use 48 +1.5V 49 No use 50 GND 51 No use 52 +3.3VSB Hardware and Installation UIM_PWR 17 GOT3157W-881-PCT User’s Manual 2.4 Mountings: Panel / Wall / Desktop / VESA There are 4 applications for the GOT3157W-881-PCT, Panel/Wall/Desktop/VESA mountings. 2.4.1 VESA/Wall-Mount The GOT3157W-881-PCT provides VESA mount: 100x100 mm. Screw four screws to fix the kit in the back chassis. About the mount, users need to buy optional wall mount kit via Axiomtek and install it on the rear cover. Wall mount (optional): VESA mount: 18 Hardware and Installation GOT3157W-881-PCT User’s Manual 2.4.2 Panel-mount Kit Assembly The GOT3157W-881-PCT is designed for panel mount application. To mount the GOT3157W-881-PCT, the standard set of mounting kit (included in the system packaging) is needed. Hardware and Installation 19 GOT3157W-881-PCT User’s Manual 2.5 HDD Installation The GOT3157W-881-PCT provides a convenient Hard Disk Drive (HDD) bracket for users to install 2.5” SATA HDD. Please follow the steps: Step 1 Refer section 2.2 to open the back cover. Step 2 Remove the HDD tray and install 2.5” HDD driver with 4 screws. 20 Hardware and Installation GOT3157W-881-PCT User’s Manual Step 3 Plug the cables to connectors and screw the HDD tray on the bracket. Installation completes. Hardware and Installation 21 GOT3157W-881-PCT User’s Manual 2.6 Installing CPU and PCH Thermal Pad It also offers CPU & PCH thermal pad for spare parts, thus you can get them from your accessory box. Please refer to the following information to replace your thermal pad if original thermal pad is damaged. Step 1 Find CPU thermal pad from accessory box. Step 2 Please remove film on thermal pad and put them on CPU, you can refer to below picture (marked via a red square. Step 3 PCH thermal is already assembled on the Heatsink. Please refer to below pictures. NOTE 22 We have installed CPU and thermal pads already. This chapter just to let you know how to replace new thermal pad by yourself. If any further information is requested, please feel free to contact Axiomtek distributors or FAE immediately. Hardware and Installation GOT3157W-881-PCT User’s Manual 2.7 DRAM Installation The GOT3157W-881-PCT provides one 204-pin DDR3 SODIMM socket that supports system memory up to 8GB. Please follow steps below to install the memory modules: Step 1 Refer to section 2.2 to open the back cover. Step 2 Find out DIMM socket on mainboard (SBC87881). Step 3 Insert the DRAM to the DIMM socket, and then push it down firmly until it is clipped by the socket. Installation completed Hardware and Installation 23 GOT3157W-881-PCT User’s Manual 2.8 Wireless LAN Card Installation The GOT3157W-881-PCT provides one Mini card slot for user to install one wireless LAN card. When installing the wireless LAN card, refer to the following instructions and illustration: Step 1 Refer to section 2.2 to open the back cover and find out mini-card slot on mainboard. Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped by the slot. 24 Hardware and Installation GOT3157W-881-PCT User’s Manual Step 3 Find the Antenna cable and connect it on wireless LAN card. …. Hardware and Installation 25 GOT3157W-881-PCT User’s Manual Step 4 Remove the antenna plug from the top of back cover, and then install the antenna on the antenna connector NOTE Please have the extended bracket when using half-size mini card. 2.9 Power Adapter Installation Step 1 Please connect power adapter to GOT3157W-881-PCT at first. The connector is with special shape to prevent wrong connection. Step 2 Connect power cord to power adapter. Step 3 Connect power cord to AC power source. 26 Hardware and Installation GOT3157W-881-PCT User’s Manual Note: Cables connection guide for install CPU by yourself. Step 1 Please refer to Chapter 2.2 for how to open back cover. Step 2 Disassemble the HDD bracket & main board. You will find below 4 cables are not connected to mainboard. Step 3 After you installed CPU, Please refer to below pictures to connect these cables. 3 1 2 4 2 1 3 Hardware and Installation 27 GOT3157W-881-PCT User’s Manual 4 28 Hardware and Installation GOT3157W-881-PCT User’s Manual Hardware and Installation 29 GOT3157W-881-PCT User’s Manual This page is intentionally left blank. 30 Hardware and Installation GOT3157W-881-PCT User’s Manual Chapter 3 AMI BIOS Setup Utility The AMI BIOS provides users with a built-in setup program to modify basic system configuration. All configured parameters are stored in a battery-backed CMOS to save the setup information whenever the power is turned off. This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility. 3.1 Starting To enter the setup screens, follow the steps below: 1. Turn on the computer and press the <Del> key immediately. 2. After you press the <Del> key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as the Advanced and Chipset menus. It is strongly recommended that you should avoid changing the chipset’s defaults. Both AMI and your system manufacturer have carefully set up these defaults that provide the best performance and reliability. 3.2 Navigation Keys The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on. NOTE Some of the navigation keys differ from one screen to another. Hot Keys Description Left/Right The Left and Right <Arrow> keys allow you to select a setup screen. Up/Down The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen. + Plus/Minus The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item. Tab The <Tab> key allows you to select setup fields. F1 The <F1> key allows you to display the General Help screen. F2 The <F2> key allows you to Load Previous Values. F3 The <F3> key allows you to Load Optimized Defaults. F4 The <F4> key allows you to save any changes you have made and exit Setup. Press the <F4> key to save your changes. Esc The <Esc> key allows you to discard any changes you have made and exit the Setup. Press the <Esc> key to exit the setup without saving your changes. Enter The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens. AMI BIOS Setup Utility 31 GOT3157W-881-PCT User’s Manual 3.3 Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as described below. The Main BIOS setup screen is shown below. System Date/Time Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format. 32 AMI BIOS Utility GOT3157W-881-PCT User’s Manual 3.4 Advanced Menu mSATA/PCIE select Use this item to select the SCN14 to mSATA or Mini-PCIE mode. Launch PXE OpROM Use this item to enable or disable the boot ROM function of the onboard LAN chip when the system boots up. The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ► ► ► ► ► ► ► ACPI Settings CPU Configuration SATA Configuration PCH-FW Configuration USB Configuration NCT6106D Super IO Configuration NCT6106D HW Monitor For items marked with “”, please press <Enter> for more options. AMI BIOS Setup Utility 33 GOT3157W-881-PCT User’s Manual ACPI Settings You can use this screen to select options for the ACPI configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface (ACPI) sleep state. Here are the options for your selection: Suspend Disabled and S3 (Suspend to RAM) S3 Video Repost Determine whether to invoke VGA BIOS POST on S3/STR resume. [Disabled] When set to [No], the system will not invoke VGA BIOS POST on S3/STR resume. [Enabled] When set to [Yes], the system invokes VGA BIOS POST on S3/STR resume. 34 AMI BIOS Utility GOT3157W-881-PCT User’s Manual CPU Configuration This screen shows the CPU Configuration, and you can change the value of the selected option. Hyper-threading This item can set enable or disable for support Hyper-threading Technology. Intel Virtualization Technology Allow you to enable or disable Intel Virtualization Technology. When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. AMI BIOS Setup Utility 35 GOT3157W-881-PCT User’s Manual SATA Configuration In the SATA Configuration menu, you can see the currently installed hardware in the SATA ports. During system boot up, the BIOS automatically detects the presence of SATA devices. SATA Mode Selection Use this item to choose the SATA operation mode. Here are the options for your selection: IDE Mode and AHCI Mode. SATA Controller Speed Use this item to choose the SATA speed. Here are the options for your selection: Auto Gen2 and Gen3. 36 Gen1, AMI BIOS Utility GOT3157W-881-PCT User’s Manual PCH-FW Configuration This screen shows the ME Firmware version, and its detail information. USB Configuration USB3.0 Support: AMI BIOS Setup Utility 37 GOT3157W-881-PCT User’s Manual XCHI Hand-off: EHCI Hand-off: 38 AMI BIOS Utility GOT3157W-881-PCT User’s Manual NCT6106D Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. For items marked with “”, please press <Enter> for more options. AMI BIOS Setup Utility 39 GOT3157W-881-PCT User’s Manual Serial Port 1 Configuration Serial Port Use this item to enable or disable serial port 1. The optimal setting for base I/O address is 3F8h and for interrupt request line is IRQ4. Change Settings Here are the options for your selection; Auto; IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Transmission Mode Use this item to configure serial port 0. Here are the options for your selection: 40 AMI BIOS Utility GOT3157W-881-PCT User’s Manual Serial Port 2 Configuration Serial Port Use this item to enable or disable serial port 2. The optimal setting for base I/O address is 2F8h and for interrupt request line is IRQ3. Change Settings Here are the options for your selection; Transmission Mode Use this item to configure serial port 0. Here are the options for your selection: RS232 RS422 RS485 AMI BIOS Setup Utility 41 GOT3157W-881-PCT User’s Manual 42 NCT6106D HW Monitor PC Health Status AMI BIOS Utility GOT3157W-881-PCT User’s Manual 3.5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus: ► PCH - IO Configuration ► System Agent (SA) Configuration For items marked with “”, please press <Enter> for more options. AMI BIOS Setup Utility 43 GOT3157W-881-PCT User’s Manual PCH - IO Configuration This screen allows users to configure PCH – IO Configuration parameters. For items marked with “”, please press <Enter> for more options. USB Configuration Use this item for further setting of USB configuration. 44 AMI BIOS Utility GOT3157W-881-PCT User’s Manual System Agent (SA) Configuration This screen allows users to configure System Agent (SA) parameters. For items marked with “”, please press <Enter> for more options. Graphics Configuration Use this item for further setting of graphics configuration. AMI BIOS Setup Utility 45 GOT3157W-881-PCT User’s Manual Primary IGFX Boot Display The only one option is LVDS. Secondary IGFX Boot Display Use this item for further setting of graphics control; we can get following items to choose HDMI interface, or disable it. LVDS Panel Type It shows the LVDS setting of panel. It is not able to change via BIOS setup. About GOT3157W-881-PCT, the configuration is “1366x768 24bit” 46 AMI BIOS Utility GOT3157W-881-PCT User’s Manual Memory Configuration Use this item for further setting of memory configuration, this screen displays memory information, and allows user to set memory configuration. AMI BIOS Setup Utility 47 GOT3157W-881-PCT User’s Manual 3.6 Boot Menu The Boot menu allows users to change boot options of the system. Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup NumLock State Use this item to select the power-on state for the NumLock. Quiet Boot Enable or disable Quiet Boot option. Boot Option Priorities These are settings for boot priority. Specify the boot device priority sequence from the available devices. 48 AMI BIOS Utility GOT3157W-881-PCT User’s Manual 3.7 Security Menu The Security menu allows users to change the security settings for the system. Administrator Password This item indicates whether an administrator password has been set (installed or uninstalled). User Password This item indicates whether an user password has been set (installed or uninstalled). AMI BIOS Setup Utility 49 GOT3157W-881-PCT User’s Manual 3.8 Save & Exit Menu The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and return to Main Menu. Select Save Changes and Exit from the Save & Exit menu and press <Enter>. Select Yes to save changes and exit. Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration and return to Main Menu. Select Discard Changes and Exit from the Save & Exit menu and press <Enter>. Select Yes to discard changes and exit. Save Changes and Reset When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save changes and reset. Discard Changes and Reset Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer. Select Discard Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to discard changes and reset. Save Changes When you have completed the system configuration changes, select this option to save changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select Yes to save changes. Discard Changes Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select Yes to discard changes. 50 AMI BIOS Utility GOT3157W-881-PCT User’s Manual Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option. Select Restore Defaults from the Save & Exit menu and press <Enter>. Save as User Defaults Select this option to save system configuration changes done so far as User Defaults. Select Save as User Defaults from the Save & Exit menu and press <Enter>. Restore User Defaults It automatically sets all Setup options to a complete set of User Defaults when you select this option. Select Restore User Defaults from the Save & Exit menu and press <Enter>. Boot Override Select a drive to immediately boot that device regardless of the current boot order. AMI BIOS Setup Utility 51 GOT3157W-881-PCT User’s Manual This page is intentionally left blank. 52 AMI BIOS Utility GOT3157W-881-PCT User’s Manual Chapter 4 Drivers Installation 4.1 Driver Disc content Please insert driver disc and browse it. It includes items as below Enter GOT3157W-881 folder. You can find two folders as “Driver” & “User’s Manual”. Select and enter “Driver”, you can find different OS folders. Win 7 driver installations. Enter Win7 folder and see 7 folders as below. Please install driver from Step 1 to 6 and reboot system. Note: Enter “Step 4 USB3.0” folder and you will find a self-execute file. Please execute it and will install driver automatic. Drivers Installation 53 GOT3157W-881-PCT User’s Manual Win 8 & above driver installations. Enter Win8-10 folder and see 6 folders as below. Please install driver from Step 1 to 5 and reboot system. 4.2 Touch Screen The GOT3157W-881-PCT uses the projected capacitive multi-touch. The specification is listed below. It also can drive the touch panel to get two fingers touch function that based on the Windows 7 & above support. Specification Touch Screen projected capacitive multi-touch Touch Screen Controller Mastouch USB Touch Screen Controller IC Communications USB interface Power Supply 5V Power Consumption 40mA Input Method Finger or Cap.Stylus Resolution 25ppi(Min.) Note: Base on WIN7 definition, ppi(Pixcel per inch) Win7 USB Driver Non-Driver Calibration Non-Calibration 54 Drivers Installation