HCTS157MS TM Radiation Hardened Quad 2-Input Multiplexers August 1995 Features Pinouts • 3 Micron Radiation Hardened CMOS SOS 16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE (SBDIP) MIL-STD-1835 CDIP2-T16 TOP VIEW • Total Dose 200K RAD (Si) • SEP Effective LET No Upsets: >100 MEV-cm2/mg • Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/ Bit-Day (Typ) • Dose Rate Survivability: >1 x 1012 RAD (Si)/s • Dose Rate Upset >1010 RAD (Si)/s 20ns Pulse • Latch-Up Free Under Any Conditions • Fanout (Over Temperature Range) - Standard Outputs 10 LSTTL Loads • Military Temperature Range: -55oC to 16 VCC S 1 1I0 2 15 E 1I1 3 14 4I0 1Y 4 13 4I1 2I0 5 12 4Y 2I1 6 11 3I0 2Y 7 10 3I1 GND 8 9 3Y +125oC • Significant Power Reduction Compared to LSTTL ICs • DC Operating Voltage Range: 4.5V to 5.5V 16 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE (FLATPACK) MIL-STD-1835 CDFP4-F16 TOP VIEW • LSTTL Input Compatibility - VIL = 0.8V Max - VIH = VCC/2 Min S 1 16 VCC 1I0 2 15 E Description 1I1 3 14 4I0 1Y 4 13 4I1 The Intersil HCTS157MS is a Radiation Hardened quad 2-input multiplexers with select and enable inputs. 2I0 5 12 4Y 2I1 6 11 3I0 The HCTS157MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of radiation hardened, high-speed, CMOS/SOS Logic Family. 2Y 7 10 3I1 GND 8 9 3Y • Input Current Levels Ii ≤ 5µA at VOL, VOH The HCTS157MS is supplied in a 16 lead Ceramic flatpack (K suffix) or a SBDIP Package (D suffix). Ordering Information PART NUMBER TEMPERATURE RANGE SCREENING LEVEL PACKAGE HCTS157DMSR -55oC to +125oC Intersil Class S Equivalent 16 Lead SBDIP HCTS157KMSR -55oC to +125oC Intersil Class S Equivalent 16 Lead Ceramic Flatpack +25oC Sample 16 Lead SBDIP HCTS157K/Sample +25oC Sample 16 Lead Ceramic Flatpack HCTS157HMSR +25oC Die Die DB NA HCTS157D/Sample CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved 1 Spec Number File Number 518610 2464.2 HCTS157MS Functional Block Diagram S E 4I1 4I0 3I1 3I0 2I1 2I0 1I1 1I0 1 15 13 12 4Y 14 10 11 9 3Y 6 3 CIRCUITS IDENTICAL TO CIRCUIT IN ABOVE DASHED OUTLINE 5 7 3 4 2 2Y 1Y TRUTH TABLE ENABLE SELECT INPUTS E S I0 I1 Y H X X X L L L L X L L L H X H L H X L L L H X H H DATA INPUTS OUTPUT H = High Level L = Low Level X = Immaterial Spec Number 2 518610 Specifications HCTS157MS Absolute Maximum Ratings Reliability Information Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . . ±10mA DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . . ±25mA (All Voltage Reference to the VSS Terminal) Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Thermal Resistance θJA θJC SBDIP Package. . . . . . . . . . . . . . . . . . . . 73oC/W 24oC/W Ceramic Flatpack Package . . . . . . . . . . . 114oC/W 29oC/W Maximum Package Power Dissipation at +125oC Ambient SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68W Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.44W If device power exceeds package dissipation capability, provide heat sinking or derate linearly at the following rate: SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7mW/oC Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 8.8mW/oC CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation. Operating Conditions Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . . . 500ns Max Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . . . . . . . 0.0V to 0.8V Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . . . . . .VCC/2 to VCC TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Quiescent Current Output Current (Sink) Output Current (Source) Output Voltage Low Output Voltage High Input Leakage Current Noise Immunity Functional Test GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC - 40 µA 2, 3 +125oC, -55oC - 750 µA 1 +25oC 7.2 - mA 2, 3 +125oC, -55oC 6.0 - mA 1 +25oC -7.2 - mA 2, 3 +125oC, -55oC -6.0 - mA VCC = 4.5V, VIH = 2.25V, IOL = 50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V VCC = 5.5V, VIH = 2.75V, IOL = 50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V VCC = 4.5V, VIH = 2.25V, IOH = -50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 5.5V, VIH = 2.75V, IOH = -50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 5.5V, VIN = VCC or GND 1 +25oC - ±0.5 µA 2, 3 +125oC, -55oC - ±5.0 µA 7, 8A, 8B +25oC, +125oC, -55oC - - - (NOTE 1) CONDITIONS SYMBOL ICC IOL IOH VOL VOH IIN FN VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIH = 4.5V, VOUT = 0.4V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VOUT = VCC - 0.4V, VIL = 0V VCC = 4.5V, VIH = 2.25V, VIL = 0.8V (Note 2) LIMITS NOTES: 1. All voltages referenced to device GND. 2. For functional tests, VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”. Spec Number 3 518610 Specifications HCTS157MS TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Data to Output SYMBOL TPHL TPLH Enable to Output TPHL TPLH Select to Output (NOTES 1, 2) CONDITIONS TPHL TPLH GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 9 +25oC 2 26 ns 10, 11 +125oC, -55oC 2 30 ns 9 +25oC 2 20 ns 10, 11 +125oC, -55oC 2 24 ns 9 +25oC 2 22 ns 10, 11 +125oC, -55oC 2 25 ns 9 +25oC 2 22 ns 10, 11 +125oC, -55oC 2 25 ns 9 +25oC 2 31 ns 10, 11 +125oC, -55oC 2 37 ns 9 +25oC 2 25 ns 10, 11 +125oC, -55oC 2 29 ns VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V LIMITS NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V. TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER SYMBOL Capacitance Power Dissipation CPD Input Capacitance Output Transition Time CIN TTHLTTLH CONDITIONS VCC = 5.0V, f = 1MHz VCC = 5.0V, f = 1MHz VCC = 4.5V NOTES TEMPERATURE MIN MAX UNITS 1 +25oC - 54 pF 1 +125oC, -55oC - 62 pF 1 +25oC - 10 pF 1 +125oC - 10 pF 1 +25oC - 15 ns 1 +125oC - 22 ns NOTE: 1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. Spec Number 4 518610 Specifications HCTS157MS TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS 200K RAD LIMITS PARAMETER (NOTES 1, 2) CONDITIONS SYMBOL TEMPERATURE MIN MAX UNITS Quiescent Current ICC VCC = 5.5V, VIN = VCC or GND +25oC - 0.75 mA Output Current (Sink) IOL VCC = 4.5V, VIN = VCC or GND, VOUT = 0.4V +25oC 6.0 - mA Output Current (Source) IOH VCC = 4.5V, VIN = VCC or GND, VOUT = VCC -0.4V +25oC -6.0 - mA Output Voltage Low VOL VCC = 4.5V and 5.5V, VIH = VCC/2, VIL = 0.8V, IOL = 50µA +25oC - 0.1 V Output Voltage High VOH VCC = 4.5V and 5.5V, VIH = VCC/2, VIL = 0.8V, IOH = -50µA +25oC VCC -0.1 - V Input Leakage Current IIN VCC = 5.5V, VIN = VCC or GND +25oC - ±5 µA Noise Immunity Functional Test FN VCC = 4.5V, VIH = 2.25V, VIL = 0.8V, (Note 3) +25oC - - - Data to Output TPHL VCC = 4.5V +25oC 2 30 ns TPLH VCC = 4.5V +25oC 2 24 ns TPHL VCC = 4.5V +25oC 2 25 ns TPLH VCC = 4.5V +25oC 2 25 ns TPHL VCC = 4.5V +25oC 2 37 ns TPLH VCC = 4.5V +25oC 2 29 ns Enable to Output Select to Output NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V. 3. For functional tests VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”. TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC) GROUP B SUBGROUP DELTA LIMIT ICC 5 12µA IOL/IOH 5 -15% of 0 Hour PARAMETER Spec Number 5 518610 Specifications HCTS157MS TABLE 6. APPLICABLE SUBGROUPS CONFORMANCE GROUPS METHOD GROUP A SUBGROUPS Initial Test (Preburn-In) 100%/5004 1, 7, 9 ICC, IOL/H Interim Test I (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H Interim Test II (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H PDA 100%/5004 1, 7, 9, Deltas Interim Test III (Postburn-In) 100%/5004 1, 7, 9 PDA 100%/5004 1, 7, 9, Deltas Final Test 100%/5004 2, 3, 8A, 8B, 10, 11 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Subgroup B-5 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas Subgroup B-6 Sample/5005 1, 7, 9 Sample/5005 1, 7, 9 Group A (Note 1) Group B Group D READ AND RECORD ICC, IOL/H Subgroups 1, 2, 3, 9, 10, 11 NOTE: 1. Alternate Group A testing in accordance with Method 5005 of MIL-STD-883 may be exercised. TABLE 7. TOTAL DOSE IRRADIATION TEST CONFORMANCE GROUPS READ AND RECORD METHOD PRE RAD POST RAD PRE RAD POST RAD 5005 1, 7, 9 Table 4 1, 9 Table 4 (Note 1) Group E Subgroup 2 NOTE: 1. Except FN test which will be performed 100% Go/No-Go. TABLE 8. STATIC BURN-IN AND DYNAMIC BURN-IN TEST CONNECTIONS OSCILLATOR OPEN GROUND 1/2 VCC = 3V ± 0.5V VCC = 6V ± 0.5V 50kHz 25kHz - 16 - - - 1 - 3, 5, 6, 10, 11, 13 - 16 - - 4, 7, 9, 12 16 2, 3, 5, 6, 10, 11, 13, 14 1 STATIC BURN-IN I TEST CONNECTIONS (Note 1) 4, 7, 9, 12 1 - 3, 5, 6, 8, 10, 11, 13 - 15 STATIC BURN-IN II TEST CONNECTIONS (Note 1) 4, 7, 9, 12 8 DYNAMIC BURN-IN TEST CONNECTIONS (Note 2) - 8, 15 NOTES: 1. Each pin except VCC and GND will have a resistor of 10KΩ ± 5% for static burn-in. 2. Each pin except VCC and GND will have a resistor of 680Ω ± 5% for dynamic burn-in. TABLE 9. IRRADIATION TEST CONNECTIONS OPEN GROUND VCC = 5V ± 0.5V 4, 7, 9, 12 8 1, 2, 3, 5, 6, 10, 11, 13 - 16 NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing. Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures. Spec Number 6 518610 HCTS157MS Intersil Space Level Product Flow - ‘MS’ Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) 100% Interim Electrical Test 1 (T1) GAMMA Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Static Burn-In 2, Condition A or B, 24 hrs. min., +125oC min., Method 1015 100% Nondestructive Bond Pull, Method 2023 100% Interim Electrical Test 2 (T2) Sample - Wire Bond Pull Monitor, Method 2011 100% Delta Calculation (T0-T2) Sample - Die Shear Monitor, Method 2019 or 2027 100% PDA 1, Method 5004 (Notes 1and 2) 100% Internal Visual Inspection, Method 2010, Condition A 100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or Equivalent, Method 1015 100% Delta Calculation (T0-T1) 100% Temperature Cycle, Method 1010, Condition C, 10 Cycles 100% Interim Electrical Test 3 (T3) 100% Constant Acceleration, Method 2001, Condition per Method 5004 100% Delta Calculation (T0-T3) 100% PDA 2, Method 5004 (Note 2) 100% PIND, Method 2020, Condition A 100% Final Electrical Test 100% External Visual 100% Fine/Gross Leak, Method 1014 100% Serialization 100% Radiographic, Method 2012 (Note 3) 100% Initial Electrical Test (T0) 100% External Visual, Method 2009 100% Static Burn-In 1, Condition A or B, 24 hrs. min., +125oC min., Method 1015 Sample - Group A, Method 5005 (Note 4) 100% Data Package Generation (Note 5) NOTES: 1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1. 2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the failures from subgroup 7. 3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004. 4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 5. Data Package Contents: • Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity). • Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage. • GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil. • X-Ray report and film. Includes penetrometer measurements. • Screening, Electrical, and Group A attributes (Screening attributes begin after package seal). • Lot Serial Number Sheet (Good units serial number and lot number). • Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test. • The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative. Spec Number 7 HCTS157MS AC Timing Diagrams AC Load Circuit DUT VIH TEST POINT INPUT VS CL VIL RL TPLH TPHL VOH VS CL = 50pF OUTPUT RL = 500Ω VOL VOH TTLH TTHL 80% VOL 20% 80% 20% OUTPUT AC VOLTAGE LEVELS PARAMETER HCTS UNITS VCC 4.50 V VIH 3.00 V VS 1.30 V VIL 0 V GND 0 V Spec Number 8 518610 HCTS157MS Die Characteristics GLASSIVATION: Type: SiO2 Thickness: 13kÅ ± 2.6kÅ WORST CASE CURRENT DENSITY: <2.0 x 105A/cm2 BOND PAD SIZE: 100µm x 100µm 4 mils x 4 mils DIE DIMENSIONS: 84 x 84 mils METALLIZATION: Type: SiAl Metal Thickness: 11kÅ ± 1kÅ Metallization Mask Layout HCTS157MS 1I0 (2) VCC (16) S (1) E (15) 1I1 (3) (14) 4I0 (13) 4I1 1Y (4) (12) 4Y 2I0 (5) (11) 3I0 2I1 (6) (10) 3I1 (7) 2Y (8) GND (9) 3Y NOTE: The die diagram is a generic plot from a similar HCS device. It is intended to indicate approximate die size and bond pad location. The mask series for the HCTS157 is TA14471A. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Spec Number 9 518610