REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5062-R117-98. - THL 98-06-12 Raymond L. Monnin B Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. – jak 04-02-26 Thomas M. Hess REV SHEET REV B B B B B B B SHEET 15 16 17 18 19 20 21 REV STATUS OF SHEETS REV B B B B B B B B B B B B B B SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PREPARED BY PMIC N/A DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 http://www.dscc.dla.mil Thanh V. Nguyen STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Thanh V. Nguyen APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, RADIATION HARDENED, HIGH SPEED CMOS, TRIPLE 3-INPUT NOR GATE, MONOLITHIC SILICON DRAWING APPROVAL DATE 95-09-14 REVISION LEVEL B SIZE CAGE CODE A 67268 5962-95780 SHEET 1 OF DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 21 5962-E129-04 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 R Federal stock class designator \ 95780 01 RHA designator (see 1.2.1) Device type (see 1.2.2) / V X Device class designator (see 1.2.3) Case outline (see 1.2.4) C Lead finish (see 1.2.5) \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 Generic number Circuit function HCS27 Radiation hardened, SOS, high speed CMOS, triple 3-input NOR gate 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter C X Descriptive designator Terminals CDIP2-T14 CDFP3-F14 14 14 Package style Dual-in-line Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 2 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC).................................................................................. DC input voltage range (VIN)................................................................................ DC output voltage range (VOUT)........................................................................... DC input current, any one input (IIN) .................................................................... DC output current, any one output (IOUT) ............................................................. Storage temperature range (TSTG)....................................................................... Lead temperature (soldering, 10 seconds).......................................................... Thermal resistance, junction-to-case (θJC): Case outline C................................................................................................... Case outline X ................................................................................................... Thermal resistance, junction-to-ambient (θJA): Case outline C................................................................................................... Case outline X ................................................................................................... Junction temperature (TJ) .................................................................................... Maximum package power dissipation at TA = +125°C (PD): 4/ Case outline C................................................................................................... Case outline X ................................................................................................... -0.5 V dc to +7.0 V dc -0.5 V dc to VCC + 0.5 V dc -0.5 V dc to VCC + 0.5 V dc ±10 mA ±25 mA -65°C to +150°C +265°C 24°C/W 30°C/W 74°C/W 116°C/W +175°C 0.68 W 0.43 W 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC).................................................................................. Input voltage (VIN)................................................................................................ Output voltage (VOUT) .......................................................................................... Maximum low level input voltage (VIL) ................................................................. Minimum high level input voltage (VIH) ................................................................ Case operating temperature range (TC) .............................................................. Maximum input rise and fall time at VCC = 4.5 V (tr, tf)......................................... Radiation features: Total dose........................................................................................................ Single event phenomenon (SEP) effective linear energy threshold (LET), no upsets (see 4.4.4.4) ................................. Dose rate upset (20 ns pulse) ......................................................................... Latch-up .......................................................................................................... Dose rate survivability ..................................................................................... 1/ 2/ 3/ 4/ 5/ +4.5 V dc to +5.5 V dc 0 V dc to VCC 0 V dc to VCC 30% of VCC 70% of VCC -55°C to +125°C 100 ns/V 5 2 X 10 Rads (Si) 2 > 100 MeV/(cm /mg) 5/ 10 > 1 X 10 Rads(Si)/s 5/ None 5/ 12 > 1 X 10 Rads(Si)/s 5/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Unless otherwise noted, all voltages are referenced to GND. The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55°C to +125°C unless otherwise noted. If the device power exceeds package dissipation capability, provide heat sinking or derate linearly (the derating is based on θJA) at the following rate: Case C ................................................................................................................... 13.5 mW/°C Case X.................................................................................................................... 8.6 mW/°C Guaranteed by design or process but not tested. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.1.1 Microcircuit die. For the requirements for microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4 3.2.6 Radiation test connections. The radiation test connections shall be as specified in table III herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 4 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Test conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified Device type VCC Group A subgroups All 4.5 V 1, 2, 3 4.40 1 4.40 1, 2, 3 5.40 1 5.40 Limits 2/ Min High level output voltage VOH For all inputs affecting output under test, VIN = 3.15 V or 1.35 V For all other inputs, VIN = VCC or GND IOH = -50 µA M, D, P, L, R 3/ All For all inputs affecting output under test, VIN = 3.85 V or 1.65 V For all other inputs, VIN = VCC or GND IOH = -50 µA 5.5 V M, D, P, L, R 3/ Low level output voltage VOL For all inputs affecting output under test, VIN = 3.15 V or 1.35 V For all other inputs, VIN = VCC or GND IOL = 50 µA IIH For input under test, VIN = 5.5 V For all other inputs, VIN = VCC or GND 1, 2, 3 0.1 1 0.1 All 5.5 V 1, 2, 3 0.1 1 0.1 All 5.5 V 1 +0.5 2, 3 +5.0 All M, D, P, L, R 3/ Input current low IIL For input under test, VIN = GND For all other inputs, VIN = VCC or GND All M, D, P, L, R 3/ Output current high (source) Output current low (sink) Quiescent supply current IOH IOL ICC 5.5 V All For all inputs affecting output under test, VIN = 4.5 V or 0.0 V For all other inputs, VIN = VCC or GND VOUT = 4.1 V M, D, P, L, R 3/ All For all inputs affecting output under test, VIN = 4.5 V or 0.0 V For all other inputs, VIN = VCC or GND VOUT = 0.4 V M, D, P, L, R 3/ All VIN = VCC or GND All M, D, P, L, R 3/ V 4.5 V M, D, P, L, R 3/ Input current high Max All M, D, P, L, R 3/ For all inputs affecting output under test, VIN = 3.85 V or 1.65 V For all other inputs, VIN = VCC or GND IOL = 50 µA Unit 4.5 V All 4.5 V All All 5.5 V 1 +5.0 1 -0.5 2, 3 -5.0 1 -5.0 1 -4.8 2, 3 -4.0 1 -4.0 1 4.8 2, 3 4.0 1 4.0 V µA mA 1 10.0 2, 3 200 1 200 µA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Device type Test conditions 1/ -55°C ≤ TC ≤ +125°C unless otherwise specified VCC Group A subgroups Limits 2/ Min Input capacitance CIN Power dissipation capacitance CPD 4/ Functional test VIH = 5.0 V, VIL = 0.0 V f = 1MHz, See 4.4.1c 5/ VIH = 3.15 V, VIL = 1.35 V See 4.4.1b tPHL 6/ CL = 50 pF RL = 500Ω, See figure 4 tPLH 6/ CL = 50 pF RL = 500Ω, See figure 4 tTHL, tTLH 7/ CL = 50 pF RL = 500Ω, See figure 4 4 10 pF 5.0 V 4 24 pF 5, 6 27 4.5 V 7, 8 7 L H 4.5 V 9 2.0 18.0 10, 11 2.0 20.0 9 2.0 20.0 All All All M, D, P, L, R 3/ Output transition time 5.0 V All All M, D, P, L, R 3/ Max All All M, D, P, L, R 3/ Propagation delay time, An, Bn, or Cn to Yn Unit 4.5 V All All 4.5 V L H 9 2.0 20.0 10, 11 2.0 22.0 9 2.0 ns 22.0 9 15.0 10, 11 22.0 ns 1/ Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table I herein. Output terminals not designated shall be high level logic, low level logic, or open, except for the ICC test, the output terminals shall be open. When performing the ICC test, the current meter shall be placed in the circuit such that all current flows through the meter. 2/ For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and the direction of current flow, respectively; and the absolute value of the magnitude, not the sign, is relative to the minimum and maximum limits, as applicable, listed herein. 3/ Devices supplied to this drawing meet all levels M, D, P, L, and R of irradiation. However, this device is only tested at the “R” level. Pre and post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TA = +25°C. 4/ Power dissipation capacitance (CPD) determines both the power consumption (PD) and current consumption (IS). Where: PD = (CPD + CL) (VCC x VCC)f + (ICC x VCC) IS = (CPD + CL)VCCf + ICC f is the frequency of the input signal. 5/ The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2 herein. For VOUT measurements, L ≤ 0.5 V and H ≥ 4.0 V. 6/ AC limits at VCC = 5.5 V are equal to the limits at VCC = 4.5 V. For propagation delay tests, all paths must be tested. 7/ This parameter is guaranteed but not tested. This parameter is characterized upon initial design or process changes which affect this characteristic. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 7 Device type All Case outlines C and X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A1 B1 A2 B2 C2 Y2 GND Y3 A3 B3 C3 Y1 C1 VCC FIGURE 1. Terminal connections. An H X X L Inputs Bn X H X L Outputs Yn L L L H Cn X X H L H = High voltage level L = Low voltage level X = Don’t care FIGURE 2. Truth table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 8 FIGURE 3. Logic diagram. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 9 NOTES: 1. CL = 50 pF minimum or equivalent (includes test jig and probe capacitance). 2. RL = 500Ω or equivalent. 3. Input signal from pulse generator: VIN = 0.0 V to VCC; PRR ≤ 10 MHz; tr ≤ 3.0 ns; tf ≤ 3.0 ns; tr and tf shall be measured from 10% VCC to 90% VCC and from 90% VCC to 10% VCC, respectively. FIGURE 4. Switching waveforms and test circuit. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 10 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA = +125°C, minimum. b. Interim and final electrical test parameters shall be as specified in table IIA herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table IIA herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B, or as modified in the device manufacturer’s quality management (QM) plan. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535, or as specified in the QM plan, including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 11 4.4.1 Group A inspection. a. Tests shall be as specified in table IIA herein. b. For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table in figure 2 herein. For device classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device. c. CIN and CPD shall be measured only for initial qualification and after process or design changes which may affect capacitance. CIN shall be measured between the designated terminal and GND at a frequency of 1 MHz. For CIN and CPD, tests shall be sufficient to validate the limits defined in table I herein. 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. b. TA = +125°C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table IIA herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25°C ±5°C, after exposure, to the subgroups specified in table IIA herein. c. When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied. 4.4.4.1 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883, method 1019 and as specified herein. 4.4.4.1.1 Accelerated aging test. Accelerated aging tests shall be performed on all devices requiring a RHA level greater than 5k rads(Si). The post-anneal end-point electrical parameter limits shall be as specified in table I herein and shall be the pre-irradiation end-point electrical parameter limit at +25°C ±5°C. Testing shall be performed at initial qualification and after any design or process changes which may affect the RHA response of the device. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 12 TABLE IIA. Electrical test requirements. Test requirements Device class M Device class Q 1,7,9 Interim electrical parameters (see 4.2) Final electrical parameters (see 4.2) Subgroups (in accordance with MIL-PRF-38535, table III) Subgroups (in accordance with MIL-STD-883, TM 5005, table I) 1,2,3,7,8,9,10,11 1/ Device class V 1,7,9 1,2,3,7,8,9,10,11 1/ 1,7,9 1,2,3,7,8,9,10,11 2/ 3/ 1,2,3,4, 5, 6, 7, 8, 9, 10, 11 1,2,3,4, 5, 6, 7, 8, 9, 10, 11 1,2,3,4, 5, 6, 7, 8, 9, 10, 11 Group C end-point electrical parameters (see 4.4) 1,2,3,7,8,9,10,11 1,2,3,7,8,9,10,11 1,2,3,7,8,9,10,11 3/ Group D end-point electrical parameters (see 4.4) 1,7,9 1,7,9 1,7,9 Group E end-point electrical parameters (see 4.4) 1,7,9 1,7,9 1,7,9 Group A test requirements (see 4.4) 1/ PDA applies to subgroup 1 and 7. 2/ PDA applies to subgroups 1, 7, 9 and deltas. 3/ Delta limits, as specified in table IIB, shall be required where specified, and the delta limits shall be completed with reference to the zero hour electrical parameters (see table I). TABLE IIB. Burn-in and operating life test, Delta parameters (+25°C). Parameters Delta limits ICC +3.0 µA IOL, IOH −15% 1/ These parameters shall be recorded before and after the required burn-in and life test to determine delta limits. 4.4.4.2 Dose rate induced latchup testing. Dose rate induced latchup testing shall be performed in accordance with test method 1020 of MIL-STD-883 and as specified herein (see 1.4 herein). Tests shall be performed on devices, SEC, or approved test structures at technology qualification and after any design or process changes which may affect the RHA capability of the process. 4.4.4.3 Dose rate upset testing. Dose rate upset testing shall be performed in accordance with test method 1021 of MIL-STD-883 and herein (see 1.4 herein). a. Transient dose rate upset testing shall be performed at initial qualification and after any design or process changes which may affect the RHA performance of the devices. Test 10 devices with 0 defects unless otherwise specified. b. Transient dose rate upset testing for class Q and V devices shall be performed as specified by a TRB approved radiation hardness assurance plan and MIL-PRF-38535. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 13 4.4.4.4 Single event phenomena (SEP). SEP testing shall be required on class V devices (see 1.4 herein). SEP testing shall be performed on a technology process on the Standard Evaluation Circuit (SEC) or alternate SEP test vehicle as approved by the qualifying activity at initial qualification and after any design or process changes which may affect the upset or latchup characteristics. The recommended test conditions for SEP are as follows: a. The ion beam angle of incidence shall be between normal to the die surface and 60° to the normal, inclusive (i.e. 0° ≤ angle ≤ 60°). No shadowing of the ion beam due to fixturing or package related effects is allowed. b. The fluence shall be ≥ 100 errors or ≥ 10 ions/cm . 6 2 5 2 2 c. The flux shall be between 10 and 10 ions/cm /s. The cross-section shall be verified to be flux independent by measuring the cross-section at two flux rates which differ by at least an order of magnitude. d. The particle range shall be ≥ 20 microns in silicon. e. The test temperature shall be +25°C and the maximum rated operating temperature ±10°C. f. Bias conditions shall be defined by the manufacturer for latchup measurements. g. Test four devices with zero failures. TABLE III. Irradiation test connections. Open Ground VCC = 5.0 V ±0.5 V 6, 8, 12 7 1, 2, 3, 4, 5, 9, 10, 11, 13, 14 NOTE: Each pin except VCC and GND will have a series resistor of 47 kΩ ±5% for irradiation testing. 4.5 Methods of inspection. Methods of inspection shall be specified as follows: 4.5.1 Voltage and current. Unless otherwise specified, all voltages given are referenced to the microcircuit GND terminal. Currents given are conventional current and positive when flowing into the referenced terminal. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 14 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.1.2 Substitutability. Device class Q devices will replace device class M devices. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform Defense Supply Center, Columbus when a system application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43216-5000, or telephone (614) 692-0547. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. 6.7 Additional information. A copy of the following additional data shall be maintained and available from the device manufacturer: a. RHA upset levels. b. Test conditions (SEP). c. Number of upsets (SEP). d. Number of transients (SEP). e. Occurrence of latchup (SEP). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 15 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95780 A.1 SCOPE A.1.1 Scope. This appendix establishes minimum requirements for microcircuit die to be supplied under the Qualified Manufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturers approved QM plan for use in monolithic microcircuits, multichip modules (MCMs), hybrids, electronic modules, or devices using chip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting of military high reliability (device class Q) and space application (device class V) are reflected in the Part or Identification Number (PIN). When available a choice of Radiation Hardiness Assurance (RHA) levels are reflected in the PIN. A.1.2 PIN. The PIN shall be as shown in the following example: 5962 R Federal Stock class designator RHA designator (see A.1.2.1) 95780 01 V 9 A Device type (see A.1.2.2) Device class designator (see A.1.2.3) Die code Die details (see A.1.2.4) Drawing number A.1.2.1 RHA designator. Device classes Q and V RHA identified die shall meet the MIL-PRF-38535 specified RHA levels. A dash (-) indicates a non-RHA die. A.1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number 01 HCS27 Circuit function Radiation hardened, SOS, high speed CMOS, triple 3-input NOR gate A.1.2.3 Device class designator. Device class Q or V Device requirements documentation Certification and qualification to the die requirements of MIL-PRF-38535. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 16 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95780 A.1.2.4 Die details. The die details designation shall be a unique letter which designates the die’s physical dimensions, bonding pad location(s) and related electrical function(s), interface materials, and other assembly related information, for each product and variant supplied to this appendix. A.1.2.4.1 Die physical dimensions. Die type Figure number 01 A-1 A.1.2.4.2 Die bonding pad locations and electrical functions. Die type Figure number 01 A-1 A.1.2.4.3 Interface materials. Die type Figure number 01 A-1 A.1.2.4.4 Assembly related information. Die type Figure number 01 A-1 A.1.3 Absolute maximum ratings. See paragraph 1.3 herein for details. A.1.4 Recommended operating conditions. See paragraph 1.4 within for details. A.2 APPLICABLE DOCUMENTS A.2.1 Government specifications, standards, bulletin, and handbooks. Unless otherwise specified, the following specification, standard, and handbook of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARD DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. HANDBOOK DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. (Copies of the specification, standards, bulletin, and handbook required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 17 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95780 A.2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. A.3 REQUIREMENTS A.3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer’s Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit or function as described herein. A.3.2 Design, construction and physical dimensions. The design, construction and physical dimensions shall be as specified in MIL-PRF-38535 and the manufacturer’s QM plan, for device classes Q and V and herein. A.3.2.1 Die physical dimensions. The die physical dimensions shall be as specified in A.1.2.4.1 and on figure A-1. A.3.2.2 Die bonding pad locations and electrical functions. The die bonding pad locations and electrical functions shall be as specified in A.1.2.4.2 and on figure A-1. A.3.2.3 Interface materials. The interface materials for the die shall be as specified in A.1.2.4.3 and on figure A-1. A.3.2.4 Assembly related information. The assembly related information shall be as specified in A.1.2.4.4 and on figure A-1. A.3.2.5 Truth table. The truth table shall be as defined in paragraph 3.2.3 herein. A.3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be as defined in paragraph 3.2.6 herein. A.3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation parameter limits are as specified in table I of the body of this document. A.3.4 Electrical test requirements. The wafer probe test requirements shall include functional and parametric testing sufficient to make the packaged die capable of meeting the electrical performance requirements in table I. A.3.5 Marking. As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a customer, shall be identified with the wafer lot number, the certification mark, the manufacturer’s identification and the PIN listed in A.1.2 herein. The certification mark shall be a “QM” or “Q” as required by MIL-PRF-38535. A.3.6 Certification of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see A.6.4 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this appendix shall affirm that the manufacturer’s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the requirements herein. A.3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall be provided with each lot of microcircuit die delivered to this drawing. A.4 QUALITY ASSURANCE PROVISIONS A.4.1 Sampling and inspection. For device classes Q and V, die sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan. The modifications in the QM plan shall not affect the form, fit or function as described herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 18 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95780 A.4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in the manufacturer’s QM plan. As a minimum it shall consist of: a) Wafer lot acceptance for class V product using the criteria defined in MIL-STD-883, test method 5007. b) 100% wafer probe (see paragraph A.3.4 herein). c) 100% internal visual inspection to the applicable class Q or V criteria defined in MIL-STD-883, test method 2010 or the alternate procedures allowed in MIL-STD-883, test method 5004. A.4.3 Conformance inspection. A.4.3.1 Group E inspection. Group E inspection is required only for parts intended to be identified as radiation assured (see A.3.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing of packaged die shall be as specified in table IIA herein. Group E tests and conditions are as specified within paragraphs 4.4.4 herein. A.5 DIE CARRIER A.5.1 Die carrier requirements. The requirements for the die carrier shall be accordance with the manufacturer’s QM plan or as specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical and electrostatic protection. A.6 NOTES A.6.1 Intended use. Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance with MIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications and logistics purposes. A.6.2 Comments. Comments on this appendix should be directed to DSCC-VA, Columbus, Ohio, 43216-5000 or telephone (614) 692-0547. A.6.3 Abbreviations, symbols and definitions. The abbreviations, symbols, and definitions used herein are defined with MIL-PRF-38535 and MIL-STD-1331. A.6.4 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed within QML-38535 have submitted a certificate of compliance (see A.3.6 herein) to DSCC-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 19 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95780 o DIE PHYSICAL DIMENSIONS Die size: Die thickness: 2200 x 2240 microns. 21 ±2 mils. o DIE BONDING PAD LOCATIONS AND ELECTRICAL FUNCTIONS The following metallization diagram supplies the locations and electrical functions of the bonding pads. The internal metallization layout and alphanumeric information contained within this diagram may or may not represent the actual circuit defined by this SMD. NOTE: Pad numbers reflect terminal numbers when placed in case outlines C, X (see figure 1). FIGURE A-1 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 20 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-95780 o INTERFACE MATERIALS 11.0kÅ ± 1.0kÅ Top metallization: SiAl Backside metallization: None. Glassivation Type: Thickness: SiO2 13.0kÅ ± 2.6kÅ Substrate: Silicon on sapphire (SOS). o ASSEMBLY RELATED INFORMATION Substrate potential: Insulator. Special assembly instructions: Bond pad #14 (VCC) first. FIGURE A-1 - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-95780 A REVISION LEVEL B SHEET 21 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 04-02-26 Approved sources of supply for SMD 5962-95780 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962R9578001V9A 34371 HCS27HMSR 5962R9578001VCC 34371 HCS27DMSR 5962R9578001VXC 34371 HCS27KMSR 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 34371 Vendor name and address Intersil Corporation 2401 Palm Bay Blvd. P.O. Box 883 Melbourne, FL 32902-0883 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.