D/CRCW-P www.vishay.com Vishay Lead (Pb)-Bearing Thick Film, Rectangular, Semi-Precision Chip Resistors FEATURES • Low temperature coefficient (50 ppm/K) and tight tolerances (± 0.25 %) • Lead (Pb)-bearing termination plating on Ni barrier layer • Metal glaze on high quality ceramic • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS MODEL CASE SIZE INCH CASE SIZE METRIC POWER RATING P70 W LIMITING ELEMENT VOLTAGE Umax. ACRMS/DC V D10/CRCW0402-P 0402 1005 0.063 50 D11/CRCW0603-P 0603 1608 0.1 75 TEMPERATURE COEFFICIENT ppm/K 0805 2012 0.125 150 ± 0.5 10 to 1M ± 50 ± 0.25, ± 0.5, ± 1 100 to 1M ± 100 ± 0.5 10 to 10M ± 50 ± 50 ± 100 D25/CRCW1206-P 1206 3216 0.25 200 CRCW1210-P 1210 3225 0.5 200 CRCW1218-P 1218 3246 1.0 200 CRCW2010-P 2010 5025 0.75 400 CRCW2512-P 2512 6332 1.0 500 RESISTANCE RANGE ± 100 ± 100 D12/CRCW0805-P TOLERANCE % ± 50 ± 0.25 100 to 1M ± 0.5, ± 1 100 to 10M ± 0.5 10 to 10M ± 0.25 100 to 1M ± 0.5, ± 1 100 to 10M ± 0.5 10 to 10M ± 0.25 100 to 1M ± 0.5, ± 1 100 to 10M ± 100 ± 0.5 100 to 1M ± 50 ± 0.5, ± 1 100 to 1M ± 100 ± 0.5 100 to 2.2M ± 50 ± 0.5, ± 1 100 to 2.2M ± 100 ± 0.5 10 to 10M ± 50 ± 0.5, ± 1 100 to 10M ± 100 ± 0.5 10 to 10M ± 50 ± 0.5, ± 1 100 to 10M SERIES E24; E96 E24; E96 E24; E96 E24; E96 E24; E96 E24; E96 E24; E96 E24; E96 Notes • These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage and permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time generally known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time. • Marking and packaging: See datasheet “Surface Mount Resistor Marking” (www.vishay.com/doc?20020). • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. Revision: 21-Jan-14 Document Number: 20009 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-P www.vishay.com Vishay TECHNICAL SPECIFICATIONS PARAMETER UNIT D10/ D11/ D12/ D25/ CRCW1210-P CRCW1218-P CRCW2010-P CRCW2512-P CRCW0402-P CRCW0603-P CRCW0805-P CRCW1206-P Rated Dissipation at P70 (1) W 0.063 0.1 0.125 0.25 0.33 1 0.5 1 Operating Voltage Umax. ACRMS/DC V 50 75 150 200 200 200 400 500 Insulation Voltage Uins (1 min) V 75 100 200 300 300 300 300 300 Insulation Resistance Operating Temperature Range °C - 55 to + 155 Failure Rate h-1 0.3 x 10-9 Weight mg 29.5 25.5 40.5 > 0.65 2 5.5 109 10 16 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRCW080525R0DKTAP C R C W 0 8 0 5 2 5 R 0 D K T A P MODEL RESISTANCE TOLERANCE TCR PACKAGING SPECIAL CRCW0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW1218 CRCW2010 CRCW2512 R = Decimal K = Thousand M = Million C = ± 0.25 % D = ± 0.5 % F = ± 1.0 % H = ± 50 ppm/K K = ± 100 ppm/K TA, TB, TC, TD, TE, TF, TG, TH, TK Up to 2 digits P= Semi-Precision PRODUCT DESCRIPTION: CRCW0805-P 100 25R 0.5% RT1 CRCW0805-P 100 75R 0.5 % RT1 MODEL TCR RESISTANCE TOLERANCE PACKAGING CRCW0402-P CRCW0603-P CRCW0805-P CRCW1206-P CRCW1210-P CRCW1218-P CRCW2010-P CRCW2512-P ± 50 ppm/K ± 100 ppm/K 49K9 = 49.9 k 5R1 = 5.1 ± 0.25 % ± 0.5 % ±1% RT1, RT5, RT6, RT7 RT4, R02, R67, R82, RT9 Revision: 21-Jan-14 Document Number: 20009 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-P www.vishay.com Vishay PACKAGING MODEL D10/CRCW0402-P D11/CRCW0603-P D12/CRCW0805-P D25/CRCW1206-P CRCW1210-P CODE QUANTITY TD = RT7 10 000 TE = RF4 50 000 TA = RT1 5000 TB = RT5 10 000 TC = RT6 20 000 TA = RT1 5000 TB = RT5 10 000 TC = RT6 20 000 TA = RT1 5000 TB = RT5 10 000 TC = RT6 20 000 TA = RT1 5000 TB = RT5 10 000 TC = RT6 20 000 CRCW1218-P TK = RT9 4000 CRCW2010-P TF = R02 4000 TG = R67 2000 TH = R82 4000 CRCW2512-P CARRIER TAPE WIDTH PITCH 8 mm 2 mm 8 mm 4 mm REEL DIAMETER 180 mm/7" 330 mm/13" 180 mm/7" 285 mm/11.25" 330 mm/13" 180 mm/7" Paper tape acc. to IEC 60068-3 Type I 8 mm 4 mm 285 mm/11.25" 330 mm/13" 180 mm/7" 8 mm 4 mm 285 mm/11.25" 330 mm/13" 180 mm/7" 12 mm 4 mm 285 mm/11.25" 12 mm 4 mm 180 mm/7" 12 mm 4 mm 180 mm/7" 330 mm/13" Blister tape acc. to IEC 60068-3 Type II 8 mm 12 mm 180 mm/7" 4 mm DIMENSIONS in millimeters SIZE SOLDER PAD DIMENSIONS DIMENSIONS INCH METRIC L W H REFLOW SOLDERING T1 T2 a b l a b l 1.0 0.9 0.9 1.0 1.3 1.2 0.9 1.3 1.3 0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5 0603 1608 1.55 + 0.10 - 0.05 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.5 0.9 0805 2012 2.0 + 0.20 - 0.10 + 0.20 - 0.10 0.3 ± 0.2 0.7 1206 3216 3.2 + 0.10 - 0.20 1210 3225 3.2 ± 0.2 0.3 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2 4.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 1.05 4.9 1.9 1.25 4.8 1.9 1218 3246 2010 5025 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 1.2 2.5 3.9 2512 6332 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2 Revision: 21-Jan-14 3.2 + 0.10 - 0.20 1.25 ± 0.15 0.45 ± 0.05 0.3 ± 0.2 WAVE SOLDERING Document Number: 20009 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-P www.vishay.com Vishay Fraction of Rated Dissipation P70 FUNCTIONAL PERFORMANCE 100 % 50 0 - 50 0 50 100 °C 150 70 Ambient Temperature in amb TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 CLAUSE TEST METHOD TEST PROCEDURE Stability for product types: D/CRCW-P REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER 1 to 10 M 4.5 - Resistance - ± 0.25 %; ± 0.5 %; ± 1 % 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown 4.13 - Short time overload U = 2.5 x P 70 x R 2 x Umax.; duration acc. to style ± (0.25 % R + 0.05 ) Solder bath method; Sn60Pb40 non-activated flux; (235 ± 5) °C (2 ± 0.2) s Good tinning ( 95 % covered) no visible damage Solder bath method; Sn96.5Ag3Cu0.5 non-activated flux; (245 ± 5) °C (3 ± 0.3) s Good tinning ( 95 % covered) no visible damage 4.17.2 58 (Td) Solderability - Temperature coefficient (20/- 55/20) °C and (20/125/20) °C ± 50 ppm/K; ± 100 ppm/K 4.32 21 (Uu3) Shear (adhesion) RR 1608 and smaller: 9 N RR 2012 and larger: 45 N No visible damage 4.33 21 (Uu1) Substrate bending Depth 2 mm; 3 times No visible damage, no open circuit in bent position ± (0.25 % R + 0.05 ) 14 (Na) Rapid change of temperature 4.8.4.2 4.19 Revision: 21-Jan-14 30 min at - 55 °C; 30 min at 125 °C 5 cycles ± (0.25 % R + 0.05 ) 1000 cycles ± (1 % R + 0.05 ) Document Number: 20009 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 D/CRCW-P www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 CLAUSE TEST METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (R) PROCEDURE Stability for product types: STABILITY CLASS 1 OR BETTER D/CRCW-P - Climatic sequence: - 4.23.2 4.23 2 (Ba) Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C; 90 % RH; 24 h; 1 cycle 4.23.4 1 (Aa) Cold - 55 °C; 2 h 4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h 4.23.6 30 (Db) Damp heat, cyclic 55 °C; 90 % RH; 24 h; 5 cycles 4.23.7 - DC load U= 1 to 10 M ± (1 % R + 0.05 ) P 70 x R U = P 70 x R Umax.; 1.5 h on; 0.5 h off; 4.25.1 - Endurance at 70 °C 70 °C; 1000 h ± (1 % R + 0.05 ) 70 °C; 8000 h ± (2 % R + 0.05 ) ± (0.25 % R + 0.05 ) 58 (Td) Resistance to soldering heat Solder bath method (260 ± 5) °C; (10 ± 1) s 4.35 - Flamability, needle flame test IEC 60695-11-5; 10 s No burning after 30 s 4.24 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days ± (1 % R + 0.05 ) 4.25.3 - Endurance at upper category temperature 155 °C, 1000 h ± (1 % R + 0.05 ) 4.40 - Electrostatic discharge (human body model) IEC 61340-3-1; 3 pos. + 3 neg. discharges; ESD voltage acc. to size ± (1 % R + 0.05 ) 4.29 45 (XA) Component solvent resistance Isopropyl alcohol; 50 °C; method 2 No visible damage 4.30 45 (XA) Solvent resistance of marking Isopropyl alcohol; 50 °C; method 1, toothbrush Marking legible, no visible damage 4.22 6 (Fc) Vibration, endurance by sweeping f = 10 Hz to 2000 Hz; x, y, z 1.5 mm; A 200 m/s2; 10 sweeps per axis ± (0.25 % R + 0.05 ) 4.37 - Periodic electric overload 15 x P 70 x R 2 x Umax.; 0.1 s on; 2.5 s off; 1000 cycles ± (1 % R + 0.05 ) 4.27 - Single pulse high voltage overload, 10 μs/700 μs 4.18.2 U= Û = 10 x P 70 x R 2 x Umax.; 10 pulses ± (1 % R + 0.05 ) All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2-x, variety of environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3. Revision: 21-Jan-14 Document Number: 20009 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000