Model 1000 Terminal Unit product sheet

Model 1000 Terminal Unit
for the Siemens Digital Level Sensor
Providing for level monitoring and control
The Model 1000 terminal unit (TU 1000) is
a solid-state, stand-alone device designed
to monitor up to 16 Siemens digital level
sensors (DLS) and to control up to ten
digital outputs. The unit is programmable
through a standard RS232 serial cable
with RTS/CTS connected to a computer
running the Model 1000 terminal configuration software or any terminal emulation
software.
Local readout for the tank levels and temperature are available via a four-line by
20-character LCD display that will display
up to two levels, temperature and tank
volume for each tank. Sockets are provided
for two optically isolated G4 digital output
modules for either alarming or controlling
based on user programmable set points for
any sensor. The G4 modules can control
either AC or DC power to dry contact
relays. An expansion board allows for
eight additional optically isolated G4
digital output modules. With this
expansion board, a total of 10 digital
outputs are available.
The unit also is capable of converting the
digital signal from a Siemens DLS to an
analog output. Optional analog output
modules can be added to provide up to
eight analog signals for top level, bottom
level or temperature. This enables Siemens
digital level sensors to be used in a system
that has only analog inputs available for
receiving tank level data.
Mechanical specifications
NEMA 4X enclosure
Optional eight D/O expansion board can
be mounted inside enclosure
Electrical specifications
Operating temperature range: -40 °C to
+85 °C
When equipped with LCD display,
operating temperature is 0 °C to 70 °C
Optional display heater available for
operation in cold environments
Power requirements: 12 to 15 VDC
Answers for energy.
Power consumption*
Standby without display: 75mA
Standby with display: 85mA
During scroll - LCD backlight: 210m A
(scrolling period is programmable)
During poll: 100mA (polling time = twosecond max)
Sleep mode: 9mA**
Analog outputs: 20mA max per channel
if unit sources loop power
*Power consumption does not include connected
level sensors.
**Sleep mode is designed for stand-alone display
applications with no digital or analog outputs
programmed.
RS232 port
4-20mA conversion accuracy*
Provided for configuration and
diagnostics
9600 baud, no parity, eight data bits,
one-stop bit
Total of 10 output sockets available
Monotonicity: 16 bit min
Two sockets provide for optically isolated
G4 modules on board (G4 modules sold
separately)
Offset drift: +/- 25 ppm of FS/°C max
Eight additional sockets with expansion
board
Total output error: (20mA) at 25 °C +/0.2% of FS max
Configuration software available
RS485 port
Total output drift: +/- 50 ppm of FS/°C
max
Communication to Siemens digital level
sensors
Four-wire communications
Resolution: 16 bit
Integral non-linearity: +/- 0.01% of FS
max offset (4mA) at 25 °C +/- 0.1%
of FS max
Communication: HyperTerminal or
similar terminal emulation software
using ASCII commands
Optional digital outputs
VCC supply sensitivity: 50 mA/mV typical
*Except as limited by sensor and protocol
Cycles power to level between polls
resolution
For more information about this and other
digital level sensor products and applications, contact us at 1 (888) 856-4528 or
[email protected].
Published by and copyright © 2010:
Siemens AG
Energy Sector
Freyeslebenstrasse 1
91058 Erlangen, Germany
Siemens Energy, Inc.
Oil & Gas Division
10730 Telge Road
Houston, TX 77095
www.siemens.com/oilandgas
Order No. E50001-D440-A143-X-76US
Printed in USA
BU 1500F IN 0910.25
All rights reserved.
Trademarks mentioned in this document are
the property of Siemens AG, its affiliates, or
their respective owners.
Subject to change without prior notice.
The information in this document contains
general descriptions of the technical options
available, which may not apply in all cases.
The required technical options should therefore
be specified in the contract.