Product is End of Life Jan-2016 and Replaced by CPR High Volume CPR www.vishay.com Vishay Dale Wirewound Resistors, Commercial Power, Radial Terminals FEATURES • • • • Direct mounting on printed circuit board Circuit board lock-in mounting tabs High performance for low cost Meets or exceeds requirements of EIA Standard RS-344 • Special inorganic potting compound and ceramic case provide high thermal conductivity in a fireproof package • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Please reference the Vishay Dale closest equivalent: CPR High Volume (www.vishay.com/doc?30261). Notes • There may be slight differences between the CPR product and the CPR High Volume product. • See the cross-reference file for a complete list of differences and part number crosses: www.vishay.net/files/Cross-Reference%20Data-without%20PC N%20-%20%20PCN-DR-020-2015%20Rev%200.pdf. Available Available Available Available Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non-RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details. STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL POWER RATING P40 °C W 3 5 7 10 15 20 HISTORICAL MODEL CPR03 CPR05 CPR07 CPR10 CPR15 CPR20 CPR-3 CPR-5 CPR-7 CPR-10 CPR-15 CPR-20 RESISTANCE RANGE 0.1 to 1K 0.1 to 1K 0.1 to 1.429K 0.1 to 2K 0.1 to 2K 0.15 to 2.855K TOLERANCE ±% 5, 10 5, 10 5, 10 5, 10 5, 10 5, 10 WEIGHT (typical) g 5.6 6.6 9.4 10.0 20.3 25.6 TECHNICAL SPECIFICATIONS PARAMETER UNIT CPR RESISTOR CHARACTERISTICS Temperature Coefficient ppm/°C ± 300 for 1.0 and above; ± 600 for less than 1.0 Short Time Overload 5 x rated power for 5 s Terminal Strength lb 10 minimum 1000 Dielectric Withstanding Voltage VAC Maximum Working Voltage V (P x R)1/2 Operating Temperature Range °C -65 to +275 Note • Wirewound CPR resistors can reliably function as a fuse and as a resistor. Such components involve compromise between fusing and resistive functions; therefore, each design should be tailored to the application to ensure optimum performance. Contact factory by using the e-mail address at the bottom of this page for design assistance. GLOBAL PART NUMBER INFORMATION Global Part Numbering example: CPR0515R00JE14 C P R 0 GLOBAL MODEL CPR03 CPR05 CPR07 CPR10 CPR15 CPR20 5 1 VALUE 5 R TOLERANCE R = decimal K = thousand R1500 = 0.15 1K500 = 1500 H = ± 3.0 % J = ± 5.0 % K = ± 10.0 % 0 0 J E 1 4 PACKAGING SPECIAL (1) E14 = lead (Pb)-free bulk E31 = lead (Pb)-free four layer bulk (1) E10 = lead (Pb)-free foam pack B14 = tin/lead bulk (1) B31 = tin/lead four layer bulk (1) F10 = tin/lead foam pack (dash number) (up to 3 digits) from 1 to 999 as applicable Historical Part Numbering example: CPR-5 15 5 % B14 CPR-5 15 5% B14 HISTORICAL MODEL RESISTANCE VALUE TOLERANCE CODE PACKAGING Note (1) Only for 3 W and 5 W sizes. Revision: 11-Feb-16 Document Number: 30219 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Product is End of Life Jan-2016 and Replaced by CPR High Volume CPR www.vishay.com Vishay Dale DIMENSIONS in inches [millimeters] B A C Maximum misalignment D 5° 0.020 ± 0.005 [0.508 ± 0.127] Material thickness G 0.180 ± 0.010 [4.57 ± 0.254] F E DIMENSIONS in inches [millimeters] GLOBAL MODEL A ± 0.040 [1.02] B ± 0.031 [0.787] C ± 0.031 [0.787] D + 0.080 [2.03] - 0.040 [1.02] E ± 0.012 [0.305] F ± 0.008 [0.203] G ± 0.060 [1.52] CPR03 0.906 [23.01] 0.375 [9.53] 0.375 [9.53] 0.394 [10.01] 0.287 [7.29] 0.055 [1.40] 0.500 [12.70] CPR05 1.060 [26.92] 0.375 [9.53] 0.360 [9.14] 0.394 [10.01] 0.287 [7.29] 0.055 [1.40] 0.590 [14.99] CPR07 1.398 [35.51] 0.375 [9.53] 0.360 [9.14] 0.984 [24.99] 0.287 [7.29] 0.055 [1.40] 0.886 [22.50] CPR10 1.888 [47.96] 0.375 [9.53] 0.360 [9.14] 0.984 [24.99] 0.287 [7.29] 0.055 [1.40] 1.380 [35.05] CPR15 1.888 [47.96] 0.500 [12.70] 0.500 [12.70] 1.180 [29.97] 0.394 [10.01] 0.106 [2.69] 1.280 [32.51] CPR20 2.498 [63.45] 0.500 [12.70] 0.500 [12.70] 1.180 [29.97] 0.394 [10.01] 0.106 [2.69] 1.870 [47.50] Element: copper-nickel alloy or nickel-chrome alloy, depending on resistance value Core: woven fiberglass Body: steatite ceramic case with inorganic potting compound Terminals: tin/lead plated CRS (Lead (Pb)-free will be 100 % tin) Part Marking: DALE, model, wattage, value, tolerance, date code RATED POWER IN % DERATING MATERIAL SPECIFICATIONS 120 100 80 60 40 20 0 - 55 - 25 25 75 40 125 175 275 225 AMBIENT TEMPERATURE IN °C PERFORMANCE TEST CONDITIONS OF TEST TEST LIMITS (EIA RS-344) Thermal Shock -55 °C to +275 °C, 5 cycles, 30 min dwell time ± (5.0 % + 0.05 ) R Short Time Overload 5 x rated power for 5 s ± (4.0 % + 0.05 ) R Dielectric Withstanding Voltage 1000 VRMS for 1 min ± (2.0 % + 0.05 ) R Low Temperature Operation -65 °C, full rated working voltage for 45 min ± (3.0 % + 0.05 ) R Humidity 75 °C, 90 % to 100 % RH, 240 h ± (5.0 % + 0.05 ) R Load Life 1000 h at rated power, +40 °C, 1.5 h “ON”, 0.5 h “OFF” ± (10.0 % + 0.05 ) R Terminal Strength 10 pounds in axial direction for 30 s ± (2.0 % + 0.05 ) R Resistance to Solder Heat Terminal immersed 3.5 s in molten solder at 1/8" to 3/16" from body ± (4.0 % + 0.05 ) R Revision: 11-Feb-16 Document Number: 30219 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000