RTOP Datasheet

RTOP
www.vishay.com
Vishay Sfernice
Power Resistors for Mounting onto a Heatsink
Thick Film Technology
FEATURES
• 1 % tolerance available
• High power rating = 200 W
• Wide ohmic value range = 0.046  to 1 M
• Non inductive
• Easy mounting
• Low thermal radiation of the case
• Standard isotop case (SOT-227 B)
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
This series of thick film power resistors include modules which can incorporate up to 2 different resistor values in the same
SOT-227B package. Two types of terminations are available along with a 4 terminal device for measurement applications in the
case of the single resistor version. This product range benefits from Vishay Sfernice’s experience in thick film power resistor
technology i.e. high power: volume ratio, low tolerance or individual resistors and excellent overload capabilities (due to the
trimming technique).
DIMENSIONS in millimeters
RTOP
V Connections
10 12.6
4
15 ± 0.3
12.6
25
30
38
Ø 4.2
Note
• Tolerances unless otherwise specified: ± 0.3 mm
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
DRTOP50
RTOP100
DRTOP100
RTOP200
SIZE
SOT-227B
RATED POWER
P25 °C
W
TOLERANCE
±%
TEMPERATURE
COEFFICIENT
± ppm/°C
0.091 to 1M
50
1, 2, 5, 10
150, 300
0.046 to 1M
100
1, 2, 5, 10
150, 300
0.046 to 1M
200
1, 2, 5, 10
150, 300
RESISTANCE RANGE

MECHANICAL SPECIFICATIONS
ENVIRONMENTAL SPECIFICATIONS
Mechanical Protection
Insulated case
Resistive Element
Cermet
Substrate
Alumina on insulated base
End Connections
V connections: screw M4 x 6
Tightening Torque Connections
1 Nm
Tightening Torque Heatsink
2 Nm
Weight
30 g max.
Temperature Range
Revision: 09-Nov-15
-55 °C to +125 °C
Climatic Category
55/125/56
TECHNICAL SPECIFICATIONS
Temperature Coefficient
(-55 °C to +125 °C)
Insulation Resistance
Standard
± 300 ppm/°C (R < 1)
± 150 ppm/°C (R > 1)
> 106 M
Document Number: 50045
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RTOP
www.vishay.com
Vishay Sfernice
PERFORMANCE
TESTS
CONDITIONS
REQUIREMENTS
IEC 60115-1
2.5 Pr/5 s US < 2 UL
< ± (0.25 % + 0.05 )
IEC 60115-1
5 cycles -55 °C +125 °C
< ± (0.25 % + 0.05 )
IEC 60115-1
Pr at 25 °C 1000 h
< ± (0.5 % + 0.05 )
IEC 60115-1/IEC 60068-2-3 Test Ca
56 days 95 % RH/40 °C
< ± (0.5 % + 0.05 )
Momentary Overload
Rapid Temperature Change
Load Life
Humidity (Steady State)
SPECIAL FEATURES
MODEL
RTOP 200
RTOP 100
DRTOP 100
DRTOP 50
200 W
5W
100 W
5W
100 W
3.5 W
50 W
3.5 W
0.5 °C/W
1 °C/W
0.5 °C/W
1 °C/W
1500 V
1500 V
500 V
500 V
Dielectric Strength (1)
Connections/Chassis
2500 V, 1 min
10 mA max.
2500 V, 1 min
10 mA max.
2500 V, 1 min
10 mA max.
2500 V, 1 min
10 mA max.
Dielectric Strength (1)
Connections/Resistors
-
-
2500 V, 1 min
10 mA max.
2500 V, 1 min
10 mA max.
Power Rating at +25 °C 
Chassis Mounted Resistors 
Unmounted Resistors
Thermal Resistance (per Resistor)
Limiting Voltage UL
Ohmic Value Range
0.046  to 1 M
0.091  to 1 M
Tolerance
± 1 % to ± 10 %
± 1 % to ± 10 %
R
R2
R1
Electrical Diagrams
R
Shunt version
Note
(1) MIL-STD-202 Method 301
Revision: 09-Nov-15
Document Number: 50045
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RTOP
www.vishay.com
Vishay Sfernice
RECOMMENDATIONS FOR MOUNTING ONTO A HEATSINK
• Surfaces in contact must be carefully cleaned.
• The heatsink must have an acceptable flatness: From 0.05 mm to 0.1 mm/100 mm.
• Roughness of the heatsink must be around 6.3 μm. In order to improve thermal conductivity, surfaces in contact (alumina,
heatsink) should be coated with a silicone grease (type SI 340 from Rhône-Poulenc or Dow 340 from Dow Corning).
RTOP
Tightening Torque on Heatsink
2 Nm
• For the electrical connections, it is recommended to use M4 x 6 screws and if necessary a washer of 1mm thickness. The
recommended screw tightening torque is 1 Nm.
CHOICE OF THE HEATSINK
The user must choose the heatsink according to the working conditions of the component (power, room temperature).
Maximum working temperature must not exceed 125 °C. The dissipated power is simply calculated by the following ratio:
T
P = ------------------------------------------------------------------------------------------R TH (j - c) + R TH (c - h) + R TH (h - a)
P:
Expressed in W
T:
Difference between maximum working temperature and room temperature.
RTH (j - c): Thermal resistance value measured between resistive layer and outer side of the resistor. It is the thermal
resistance of the component (see table Special Features).
RTH (c - h): Thermal resistance value measured between outer side of the resistor and upper side of the heatsink.
This is the thermal resistance of the interface (grease, thermal pad), and the quality of the fastening device.
RTH (h - a): Thermal resistance of the heatsink.
Example:
RTH (c - a): For RTOP 200 power rating 130 W at ambient temperature + 30 °C.
Thermal resistance (see table 1) RTH (j - c): 0.5 °C/W
T = 125 °C - 30 °C  95 °C 
T
95
RTH (j - c) + RTH (c - h) + RTH (h - a) = ------- = ------- = 0.73 °C/W
P
130
RTH (j - c) = 0.112 °C/W
RTH (c - h) + RTH (h - a) = 0.73 °C/W - 0.5 °C/W  0.23 °C/W
Revision: 09-Nov-15
Document Number: 50045
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RTOP
www.vishay.com
Vishay Sfernice
OVERLOADS
POWER RATING
The applied power is 2.5 x rated power for 5 s with a max.
voltage of 2 x nominal voltage.
Accidental overload: The values indicated in the graph
below are applicable to resistors in air or mounted onto a
heatsink. 
In case of multi-resistor devices, (DRTOP, TROP and QROP)
the results apply to each resistor value in the device.
The temperature of the heater should be maintained in the
limit specified. To improve the thermal conductivity,
surfaces in contact should be laid on with a silicon grease
and the torque applied on the screw for tightening should be
around 2 Nm.
100
RATED POWER IN %
ENERGY CURVE
ENERGY IN JOULES
1000
100
RTOP
10
DRTOP
1
80
60
40
20
0.1
0
0
0.01
10-7
20
40
60
80
100
120
140
HEATSINK TEMPERATURE IN °C
10-6
10-5
10-4
10-3
10-2
10-1
100
OVERLOAD DURATION IN s
PACKAGING
POWER CURVE
Box of 10 units
1 000 000
POWER IN W
100 000
10 000
RTOP
DRTOP
1000
100
10-7
10-6
10-5
10-4
10-3
10-2
10-1
100
OVERLOAD DURATION IN s
MARKING
Series, style, ohmic value (in), tolerance
manufacturing date, Vishay Sfernice trademark.
Revision: 09-Nov-15
(in
%),
Document Number: 50045
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RTOP
www.vishay.com
Vishay Sfernice
ORDERING INFORMATION
RTOP
200
5U
±1%
DRTOP
50
150U
5%
±%
15U
5%
R1
MODEL
STYLE
RTOP
DRTOP
100
50
OHMIC
VALUE
V
T1
ABSOLUTE TOLERANCE PER
RESISTOR
Optional
±1%
±2%
±5%
± 10 %
V
XXX
BO10
e
CONNECTIONS
CUSTOM
DESIGN
PACKAGING
LEAD
(Pb)-FREE
V: screw
VS: RTOP shunt
Optional
R2
To be precise
for each
resistor
GLOBAL PART NUMBER INFORMATION
R
GLOBAL
MODEL
RTOP
Revision: 09-Nov-15
T
O
P
1
0
0
V
5
R
0
0
K
B
SIZE
LEADS
OHMIC VALUE
TOLERANCE
PACKAGING
SPECIAL
100
200
V = screw
VS = RTOP shunt
The first three digits are
significant figures and the
last digit specifies the
number of zeros to follow.
R designates decimal point.
48R7 = 48.7 
4871 = 4870 
1002 = 10 000 
R010 = 0.01 
R680 = 0.68 
2701 = 2.7 k
F=1%
G=2%
J=5%
K = 10 %
B = box
10 pieces
As applicable
Ex = UA1
Document Number: 50045
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000