PMM0204 NOT FOR NEW DESIGNS Vishay Draloric Metal Film, Cylindrical Resistors FEATURES • Stable metal film on high quality ceramic • Very low TC and tight tolerances • Excellent stability at different environmental conditions • Pure tin termination on nickel barrier, plated on press fit steel caps • Compatible with lead (Pb)-free and lead containing soldering processes • Lead (Pb)-free and RoHS compliant STANDARD ELECTRICAL SPECIFICATIONS POWER RATING1) P70 W LIMITING ELEMENT VOLTAGE2) DC or AC rms V TEMPERATURE COEFFICIENT ppm/K TOLERANCE % RESISTANCE RANGE Ω E-SERIES PMM0204 0.125 100 ±5 ± 0.1; ± 0.25 100R - 100K 96 - 192 PMM0204 0.125 100 ± 10 ± 0.1; ± 0.25 100R - 221K 96 - 192 PMM0204 0.125 100 ± 15 ± 0.1; ± 0.25 100R - 221K 96 - 192 PMM0204 0.125 100 ± 25 ± 0.1; ± 0.25 100R - 221K 96 - 192 PMM0204 0.125 100 ± 50 ± 0.1; ± 0.25 100R - 221K 96 - 192 MODEL 1) 2) • Permissible dissipation depends on the maximum temperature at the solder point, the component placement density and the substrate material. Rated voltage: TC ≤ 10 ppm/°C: temperature range is - 10 °C to + 85 °C • Without TC-band, TC marking on label only • Marking: According to IEC 60062; see also datasheet “surface mount resistor marking” (document number: 20020) PxR . TECHNICAL SPECIFICATIONS PARAMETER UNIT PMM0204 Rated Dissipation at 70 °C W 0.125 Limiting Element Voltage, DC or AC rms V 100 Insulation Voltage (1 min), DC or AC peak V 200 K/W ≤ 220 Insulation Resistance Ω ≥ 10 10 Category Temperature Range °C - 10 to + 100 10-9/h <1 g 18 Thermal Resistance3) Failure Rate Weight/1000 pcs 3) Based on measurements on test board acc. to EN 140400. www.vishay.com 42 For Technical questions contact: [email protected] Document Number: 20006 Revision: 15-Feb-06 PMM0204 Vishay Draloric Metal Film Cylindrical Resistors DIMENSIONS DIMENSIONS [in millimeters] MODEL PMM0204 Dmax d* L Amax Amin 1.4 D - 0.15 3.6 - 0.15 0.85 0.5 * d measured in the middle of the resistor SOLDER PAD DIMENSIONS [in millimeters] REFLOW SOLDERING WAVE SOLDERING MODEL PMM0204 a b l a b l 1.0 1.6 2.2 1.2 1.6 2.2 0 0 PART NUMBER AND PRODUCT DESCRIPTION1) PART NUMBER2): PMM02040E5620CB0 P MODEL/SIZE PMM0204 M M 0 2 0 SPECIAL CHARACTER 0 = neutral 4 0 TC G = ± 5 ppm/K F = ± 10 ppm/K E = ± 15 ppm/K D = ± 25 ppm/K C = ± 50 ppm/K E 5 6 2 VALUE 3 digit value 1 digit multiplier 0000 = Jumper Multiplier 0 = *100 1 = *101 2 = *102 3 = *103 0 C B TOLERANCE B = ± 0.1 % C = ± 0.25 % 0 PACKING3) B1 B3 B0 M3 SPECIAL up to 2 digits 00 = standard PRODUCT DESCRIPTION: PMM0204 15 562R 0.25% B0 PMM0204 15 562R 0.25 % B0 MODEL TC RESISTANCE VALUE TOLERANCE PACKING3) PMM0204 ± 5 ppm/K ± 10 ppm/K ± 15 ppm/K ± 25 ppm/K ± 50 ppm/K 100R = 100 Ω 221K = 221K Ω ± 0.1 % ± 0.25 % B1 B3 B0 M3 Note 1. Products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER. 2. The PART NUMBER is shown to facilitate the introduction of a unified part numbering system. Currently, this PART NUMBER is applicable in the Americas only. 3. Please refer to table PACKING, see below. Document Number: 20006 Revision: 15-Feb-06 For Technical questions contact: [email protected] www.vishay.com 43 PMM0204 Vishay Draloric Metal Film Cylindrical Resistors PACKING BLISTER TAPE ON REEL ACC. IEC 60286-3 MODEL BULK CASE ACC. IEC 60286-6 DIAMETER PIECES/REEL CODE 180 mm/7" 1000 B1* 180 mm/7" 3000 B3 330 mm/13" 10000 B0 PMM0204 PIECES/ BULK CASE CODE 3000 M3 * For TC ≤ 25 ppm/K and Tolerance ≤ 0.25 % only. 120 Current Noise in µV/V Rated Power in % Further information about PACKING, see also datasheet “surface mount resistor packing” (document number: 20014) 100 80 60 3 2 1 0.5 0.3 0.1 40 0.05 0.03 20 0 - 55 - 25 Derating 0 25 50 75 100 70 Ambient Temperature in °C 0.01 1K 5K 10K Current Noise 50K 100K 500K 1M Resistance Value in Ω PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70 °C IEC 60115-1, 4.25.1 1000 hours at 70 °C, 1.5 hours "ON", 0.5 hours "OFF" ≤ 0.1 % Endurance at UCT IEC 60115-1, 4.25.3 1000 hours at 125 °C without load ≤ 0.1 % Overload Test IEC 60115-1, 4.13 Short time overload for 2 seconds 2.5 x rated voltage or ≤ 2 x limiting element voltage ≤ 0.02 % Thermal Shock IEC 60115-1, 4.19 and IEC 60068-2-14 Rapid change between upper and lower category temperature, 5 cycles ≤ 0.02 % Damp Heat Steady State IEC 60115-1, 4.24 and IEC 60068-2-78 56 days at 40 °C and 93 % relative humidity ≤ 0.2 % Resistance to Soldering Heat IEC 60115-1, 4.18 and IEC 60068-2-58 10 seconds at 260 °C solder bath temperature ≤ 0.05 % www.vishay.com 44 For Technical questions contact: [email protected] TEST RESULTS Document Number: 20006 Revision: 15-Feb-06 PMM0204 Metal Film Cylindrical Resistors Vishay Draloric APPLICABLE SPECIFICATIONS • EN 140401-803 • EN 140400 • EN 60115-1 Document Number: 20006 Revision: 15-Feb-06 For Technical questions contact: [email protected] www.vishay.com 45 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1