HML www.vishay.com Vishay Techno Thick Film Resistors, Industrial, Miniature, Axial-Leaded FEATURES • Small case size: 0.073" x 0.036" • Rugged plastic housing • Non-inductive design • 100 % pure tin solder coating on nickel leadwires. Suitable for soldering and welding. • Operating temperature range: - 55 °C to + 150 °C • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL POWER RATING P70 °C W MAXIMUM WORKING VOLTAGE (1) V 0.063 50 HML01 RESISTANCE RANGE TOLERANCE ±% TEMPERATURE COEFFICIENT ± ppm/°C 1 to 9.1 2, 5, 10 300 10 to 22M 1, 2, 5, 10 100, 200, 300 Zero-ohm jumper: Rmax. = 30 m, Imax. = 1.2 A Notes (1) Continuous working voltage shall be P x R or maximum working voltage, whichever is less • Consult factory for extended resistance range Rated Power in % DERATING CURVE MATERIAL SPECIFICATIONS 120 Resistive element 100 Encapsulation 80 Substrate 60 Termination Ruthenium oxide Plastic shell High purity 96 % alumina Solder-coated nickel leadwire 40 20 0 - 55 0 - 25 25 50 75 100 125 150 175 Ambient Temperature in °C 70 GLOBAL PART NUMBER INFORMATION Global Part Numbering: HML0110K0FKE05 (preferred part number format) H M L 0 1 1 0 K 0 F K E 0 5 GLOBAL MODEL RESISTANCE VALUE TOLERANCE CODE TEMPERATURE COEFFICIENT PACKAGING CODE (see Standard Electrical Specifications table) R= K = k M = M 9R10 = 9.1 43K2 = 43.2 k 1M20 = 1.2 M 0000 = 0 Jumper F=±1% G=±2% J=±5% K = ± 10 % Z = 0 jumper K = 100 ppm N = 200 ppm M = 300 ppm S = Special, 0 jumper E05 = Lead (Pb)-free, lacer Revision: 18-Nov-13 SPECIAL Blank = Standard (dash number) (up to 3 digits) From 1 to 999 as applicable Document Number: 68038 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 HML www.vishay.com Vishay Techno DIMENSION in inches (millimeters) A1 max. D C A E B MODEL A (LENGTH) B (WIDTH) C (HEIGHT) A1 max. (CLEAN LEAD) D (LEAD DIA) E (LEAD LENGTH) HML01 0.073 ± 0.002 (1.85 ± 0.05) 0.036 ± 0.002 (0.91 ± 0.05) 0.036 ± 0.002 (0.91 ± 0.05) 0.093 (2.36) 0.0074 ± 0.0001 (0.188 ± 0.003) 1.400 ± 0.100 (35.56 ± 2.54) Revision: 18-Nov-13 Document Number: 68038 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000