AL8811EV1 User Guide General Description The MR16 LED Driver Standard Evaluation board shows how to use the new AL8811 as a Boost LED driver for an inexpensive PFC front end and the new AL8807A as a Buck LED driver for a cost effective MR16 LED Driver circuit from which high PFC (~0.9) can be achieved. Key Features Parameter Value Input Voltage LED Current Number of LEDs 12VAC 660mA (Adjustable) 3 LEDs in series (Under Tested) 2.0 ” x 2.2” XY Dimension EVB (Rev3.3) Non-Dimmable or Triac Dimmable Front end Constant On time PFC circuit using the AL8811 Boost IC New AL8807A Buck LED Driver PFC for the 12VAC input allowing multiple MR16 units on one transformer Compatible with Electronic Transformers Applications AL8811EV1 Specifications MR16 LED Bulb Desktop lamps Under the counter lamps AL8811EV1 Rev2 March 2013 www.diodes.com Figure 1: Top View Connection Instructions Input Voltage: 12VAC (AC+, AC-) LED Outputs: LED+ (Red), LED- (Black) Page 1 of 18 AL8811EV1 User Guide Block Diagram: 12VAC Input AL8811EV1 PFC Boost LED Driver AL8811 Bridge rectifier Buck LED Driver AL8807A LEDs Phase Detect Triac Dimming Figure 2: Block Diagram Evaluation Board Schematic Figure 3: Evaluation Board Schematic AL8811EV1 Rev2 March 2013 www.diodes.com Page 2 of 18 AL8811EV1 User Guide Evaluation Board Layout Figure 4: PCB Board Layout Quick Start Guide 1. By default, the evaluation board is preset at 660mA LED Current by R11. 2. Ensure that the AC source is switched OFF or disconnected. 3. Connect the 12VAC AC line wires of power supply to two test points of “12VAC” on the left side of the board. 4. Connect the anode wire of external LED string to LED+ output test point. 5. Connect the cathode wire of external LED string to LED- output test point. 6. Turn on the main switch. LED string should light up. AL8811EV1 Rev2 March 2013 www.diodes.com Page 3 of 18 AL8811EV1 User Guide Bill of Material # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Name IC1 IC2 Q1 Q2 D1-D4, D6,D8,D9 D5,D7 L1 L2 R1 R2 R3 R4 R5, R10 R6 R7, R8, R12 R9, R13 R11 C1, C3 C2, C5, C6, C10, C11 20 C4, C7 21 C8, C9 Quantity 1 1 1 1 Part number 7 2 1 1 1 1 SBR3U30P1 1 1 2 1 MCR25JZHFLR330 3 2 1 2 ERJ-2RKF4701X AL8811 AL8807A MMBT3904-7-F ZXMN6A11Z BAV70-7-F SRR1280-221K ASPI-104S-101M-T ERJ-2RKF10R0X ERJ—2RKF4700X ERJ-2RKF2201X ERJ-2RKF1001X ERJ-2RKF5902X ERJ-3GEY0R00V RL1220S-R15-F C0402C102J5GACTU C2012X5R1E106K125 AB C1005X7R1H104K050 BB 5 2 2 ELXZ500ELL680MF15 Manufacturer Diodes Inc Diodes Inc Diodes Inc Diodes Inc Description Boost IC Buck LED Driver Diodes Inc Diodes Inc Bourns Abracon Panasonic Panasonic Rohm Semiconductor Panasonic Panasonic Panasonic Super Barrier Rectifiers Panasonic Panasonic Susumu Kemet 4.7kΩ Resistor 1/10W 1% 0402 SMD TDK 10µF Cer Cap 25V 10% X5R 0805 TDK United Chemi 0.1µF Cer Cap 50V 10% X7R 0402 NPN transistor N-MOSFET BAV70 Dual diodes 220µH, 1.6A Inductor for PFC stage 100µH, 1.35A Inductor for Buck Stage 10Ω Resistor 1/10W 1% 0402 SMD 470Ω Resistor 1/10W 1% 0402 SMD 0.33Ω Resistor 1/2W 1% 1210 SMD 2.2kΩ Resistor 1/10W 1% 0402 SMD 1kΩ Resistor 1/10W 1% 0402 SMD 59kΩ Resistor 1/10W 1% 0402 SMD 0Ω Resistor 1/10W 1% 0603 SMD 0.15Ω Resistor 1/3W 1% 0805 SMD 1000pF Cer Cap 50V 5% 0402 SMD 68µF Aluminum Cap 50V 20% Radial Functional Performance (Three series LEDs @660mA) AL8811EV1 Standard Board Performance (without dimmer and electronic transformer) Manuf Board Type VIN (VRMS) IIN (IRMS) PIN (W) PF VLED (V) ILED (mA) PLED (W) Diodes Inc AL8811EV1 Standard Board 12 694.5 7.77 0.95 8.65 659.1 5.7 AL8811EV1 Rev2 March 2013 www.diodes.com ILED Ripple (%) 8 Efficiency (%) 73.4 Page 4 of 18 AL8811EV1 User Guide Functional Waveforms For 120VAC dimmable MR16 design bench testing: The electronic transformer type is Hatch RS12-150 / 150W. The dimmer type is Lutron SELV-300P. Following is a block diagram of the bench circuit that indicates voltage and current designations where the scope plots are functionally captured on the bench set-up. The bench set-up is used in the evaluation of the AL8811EV1 Standard dimmable MR16 design. Figure 5: Bench Set-up Circuit AL8811EV1 Rev2 March 2013 www.diodes.com Page 5 of 18 AL8811EV1 User Guide Waveform #1 (Maximum Dimming) => Channel 1: V1; Channel 2: I1 Waveform #2 (Dimming Control from full to lowest brightness) => Channel 1: V1 AL8811EV1 Rev2 March 2013 www.diodes.com Page 6 of 18 AL8811EV1 User Guide Waveform #3 (Maximum Dimming) => Channel 1: V2; Channel 2: I2 Waveform #4 (Zoom-in for Maximum Dimming) => Channel 1: V2; Channel 2: I2 AL8811EV1 Rev2 March 2013 www.diodes.com Page 7 of 18 AL8811EV1 User Guide Waveform #5 (Maximum Dimming) => Channel 1: V2; Channel 2: I2 Waveform #6 (Dimming Control from full to lowest brightness) => Channel 1: V2 AL8811EV1 Rev2 March 2013 www.diodes.com Page 8 of 18 AL8811EV1 User Guide Waveform #7 (Dimming Control from full to lowest brightness) => Channel 2: I2 Waveform #8 (Maximum Dimming) => Channel 1: V2; Channel 2: I2; Channel 3: I3 AL8811EV1 Rev2 March 2013 www.diodes.com Page 9 of 18 AL8811EV1 User Guide Waveform #9 (Maximum Dimming) => Channel 1: V2; Channel 2: I2; Channel 3: IL1 (L1 current) Waveform #10 (Maximum Dimming) => Channel 1: V2; Channel 2: I2; Channel 3: IL1 (L1 current) AL8811EV1 Rev2 March 2013 www.diodes.com Page 10 of 18 AL8811EV1 User Guide Waveform #11 (Maximum Dimming) => Channel 3: I3; Channel 4: V3 Waveform #12 (Dimming Control from full to lowest brightness) => Channel 3: I3 AL8811EV1 Rev2 March 2013 www.diodes.com Page 11 of 18 AL8811EV1 User Guide Functional Data Curves AL8811EV1 Rev2 March 2013 www.diodes.com Page 12 of 18 AL8811EV1 User Guide Transformer Compatibility List 1) 120VAC to 12VAC Electronic Transformers without dimmers in 3 LEDs in series: Electronic Transformers (120VAC to 12VAC) Index Brand Model 1 HATCH RS12-30M-LED (30W) 2 RSA RT60A (60W) 3 HATCH RS12-150 (150W) 4 HATCH RS12-60M-LED (60W) 5 HATCH VS12-75W (75W) 6 LIGHTECH LET303 (300W) 7 HATCH RS12-60M (60W) 8 HATCH RS12-80M (80W) 9 HATCH VS12-60M (60W) 10 HATCH RS12-105 (105W) 11 LIGHTECH LET75 (75W) 12 HATCH VS12-60W (60W) 13 HATCH RS12-15M-LED (15W) AL8811EV1 Rev2 March 2013 www.diodes.com Performance Result (No flicker) √ √ √ √ √ √ √ √ √ √ √ √ √ Page 13 of 18 AL8811EV1 User Guide 2) 120VAC to 12VAC Electronic Transformers with dimmers in 3 LEDs in series Electronic Transformers (120VAC to 12VAC) Index Brand Model 1 HATCH RS12-30M-LED (30W) 2 HATCH RS12-150 (150W) 3 HATCH RS12-60M-LED (60W) 4 HATCH RS12-150/150W 5 LIGHTECH VS12-75W (75W) 6 HATCH RS12-60M (60W) 7 HATCH LET75 (75W) 8 HATCH VS12-60W (60W) 9 HATCH RS12-15M-LED (15W) Note: √ = No Flicker AL8811EV1 Rev2 March 2013 www.diodes.com 120VAC Dimmer Type LUTRON SELV-300P / 300W LUTRON MAELV-600 / 600W √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ Page 14 of 18 AL8811EV1 User Guide Application Information Circuit Description This design consists of three sections: 1) The input PFC circuit converts the 12VAC input voltage to a DC voltage around 30V (AL8811). 2) The output Buck LED Driver drives the three LEDs in series at a fixed current (AL8807A). 3) Finally, the phase-detect circuit generates a voltage proportional to the phase of the incoming AC voltage (when triac dimming is used). PFC Circuit The AL8811 Boost converter is a simple “Constant ON time controller”. By keeping the same ON time throughout the AC cycle, the circuit will draw a current that will closely match the voltage and result in a constant input current. This eliminates the classic peak current problem with a bridge rectifier and a large input filter capacitor. The PFC circuit includes the input bridge rectifier, EMI filter (if needed) and the AL8811 Boost converter. The AC input voltage is rectified by the bridge circuit and filtered by C1, R1, C4, and C5. This first filter removes the high frequency that is generated by the Electronic Transformer in the range of 20-30 KHz. An additional diode rectifier circuit (D5, C2) is used to generate a voltage that is used to power the circuit that will turn on/off the external MOSFET of the Boost converter. This circuit is very important as the gate drive of the MOSFET has to be greater than 3-4 volts throughout the AC cycle. The external MOSFET is used to reduce the heat dissipation in the AL8811. The AL8811 has a current limit resistor R3 which sets the maximum current allowed through the inductor L1. The output voltage is set by the divider R6, R5 to an output of around 35 volts. The output voltage is filtered by the two capacitors C8 and C9. These two capacitors store energy that will be used when the input voltage is low during the AC cycle. Buck LED Driver The AL8807A is a step-down DC-DC converter designed to drive LEDs with a constant current. The current through the LED is controlled by R11. In the present Evaluation board, the current is set to around 660mA based on a resistor value of 0.15Ω. The current is set using the “CTRL” input pin which in this new version of the IC can vary from 0 to 2.5V, controlling the current from 0mA to the maximum current at 2.5V. This control input pin is used to lower the LED current as the TRIAC dims the LED. In this way, the energy stored in the two output capacitors AL8811EV1 Rev2 March 2013 www.diodes.com Page 15 of 18 AL8811EV1 User Guide of the PFC circuit will be able to provide current throughout the AC cycle. TRIAC Phase Detection Circuit The phase of the TRIAC is detected by using an additional rectifier circuit that generates a voltage in proportional to the phase of the TRIAC Driver. This is done by rectifying the input AC voltage and averaging the energy using a resistor to charge a capacitor. Two additional resistors in series, R12 and R8, slowly discharge this circuit so it will follow the input phase change. The two resistors, R12 and R8, are used to scale the voltage so the range is from 0 to 2.6V to the Buck LED driver control pin. A simple transistor emitter follower circuit is used to drive a 1KΩ resistor in the emitter circuit. This low resistance is needed to drive the input control pin of the AL8807A LED driver because the pin outputs a small current of 50uA, which limits the lowest control voltage to around 50 mV. Setting the LED output current (AL8807A): The LED output current is set using resister R11 and the formula: ILED = VTH / R11 where VTH is equal to 0.1V For a current of 660mA, R11 is about 0.15Ω. Setting the PFC Variables (AL8811) The choice for the size of the boost converter inductor selected in this design is based on a compromise which it is able to support a peak current to around 1.5A since the average input voltage will be around 12-14V. The boost converter (AL8811) includes a current limit resistor R3 which will limit the current through the inductor and thus the power delivered to the output load. The formula for the resistor is: IPK(switch) = 0.33V / R3 For a current limit of 1A, R3 is 0.33Ω. In this evaluation design, this value was selected based on having three LEDs in series drawing about 660mA. It was found that two 68µF capacitors mounted in parallel would just fit into the cavity of the MR16 bulb. The important design goal is to have the PFC circuit, which is used to always draw current from the Electronic Transformer. AL8811EV1 Rev2 March 2013 www.diodes.com Page 16 of 18 AL8811EV1 User Guide Performance Description The evaluation board allows the testing of different combinations of circuit component values to match the final design specifications. The main design goal is to have a constant load on the Electronic Transformer so that it will be operating throughout the AC cycle. This is accomplished when the input power is about the same as the output power. Overall, there are three major components that are essential to the operation of the circuit. The first component to select is the resistor (R11) in the Buck LED driver (AL8807A) that sets the final current through the LED string. This will set the amount of power the system needs. The second component is the size of the R3 which limits the current provided to the output filter capacitors. This should be adjusted so that the boost input circuit by AL8811 LED driver is always running and thus providing a load to the Electronic Transformer. This usually means that the output voltage of the PFC circuit will have a large ripple. This will be okay as long as the lowest voltage is higher than the maximum final LED string voltage. The third component is the output capacitors (C8 and C9) of the PFC circuit. These should not be too large that the PFC circuit stops working. If it happens, the resonant circuit of the Electronic Transformer will become erratic and cause the LEDs to flicker. AL8811EV1 Rev2 March 2013 www.diodes.com Page 17 of 18 AL8811EV1 User Guide IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2013, Diodes Incorporated www.diodes.com AL8811EV1 Rev2 March 2013 www.diodes.com Page 18 of 18