ZXTR21XXEV1 User Guide

ZXTR21XXEV1 USER GUIDE
Description
The board is intended for the evaluation of
ZXTR21XXF series high voltage 60V linear
regulators with fixed 5V, 8V and 12V output
voltages in SOT23. Refer to table 1 for
detailed labelling.
The board can provide regulated 5V output
from an input voltage within the range of 7V
to 60V. Regulated 8V and 12V outputs can
be provided from input voltage ranges of
(12 to 60) V and (15 to 60) V respectively. All
the outputs can provide up to 50mA output
The evaluation board is ideal for generating current.
5V, 8V and 12V from a nominal 12V or 24V
or 48V rails connected to the common input Load can be applied to all the 9 outputs
on the board. It can supply well-regulated either individually or simultaneously as long
voltage rails, as well as, withstand and as the maximum temperature rating is not
maintain regulation during very high and fast exceeded. Refer to the datasheets for further
voltage transients.
details on max operating conditions and
regulation tolerances.
SOT23
5V Output
ZXTR2105F
8V Output
ZXTR2108F
12V Output
ZXTR2112F
Table 1
Ordering Information
ORDER NUMBER
ZXTR21XXEV1
Please note evaluation boards are subject to availability and qualified leads
Figure 1 ZXTR21XXEV1 evaluation board
Issue 1.0 November 2015
www.diodes.com
© Diodes Incorporated, 2015
ZXTR21XXEV1
Quick Start Guide
Connect a DC supply voltage to the terminal block P1 and once this voltage is set to the right
range (recommended min voltage for 5V, 8V and 12V regulation is 7V, 10V and 15V
respectively) test points will start to regulated the voltage at rated value. Required loads can
be connected to the test points. Typical performance details are provided in the sections
below.
ZXTR21XXEV1 Schematic
Figure 2 Evaluation board schematic diagram
Parts List
Designator
Description
Package
Part Number
Manufacturer
C1, C2, C3
Capacitor, 1uF 50V X7R
C1206X105K5RACTU
1206
C1206X105K5RACTU
Farnell
C4, C5, C6, C7, C8,
C9, C10, C11
Capacitor, 2.2uH 100V X7R
12061C225KAT2A
1206
12061C225KAT2A
Farnell
P1
Phoenix Terminal Block, 2 way,
1725656
1206
1725656
Farnell
R1, R2
RESISTOR, THICK FILM, 510KOHM,
250mW, 1%
1206
CRCW1206510KFKEA
Farnell
R3
RESISTOR THICK FILM, 1MOHM,
1%, 1206
1206
CR1206-FX-1004ELF
Farnell
TP1, TP2, TP3, TP4,
TP5, TP6
Vero loop terminal test point 20313137
test point 20313137
20-313137
Farnell
U1
U2
U3
5V output, voltage regulator
8V output, voltage regulator
12V output, voltage regulator
SOT23
SOT23
SOT23
ZXTR2105F
ZXTR2108F
ZXTR2112F
Diodes Inc
Diodes Inc
Diodes Inc
Table 1 Parts list
Issue 1.0 November 2015
www.diodes.com
© Diodes Incorporated, 2015
2
ZXTR21XXEV1
Performance
Figure 3 to 8 show the performance of the ZXTR21XXEV1. Figure 3 shows the quiescent
current of the ZXTR21XX is around 3.5mA at VIN=24V when the VOUT terminals are left
floating.
Iq of the Evaluation board
12
Iq (mA)
10
8
6
Iq of the Evaluation
board
4
2
0
0
20
40
60
Input voltage (V)
Figure 3 Quiescent supply current vs. supply voltage VCC
For a fixed load of 15mA, figure 4 shows the regulation of three output voltages as the input
voltage is swept from their respective minimum voltages to 60V. Load is applied to one
output at a time.
Vin Vs Vout
14
12
Iout = 15mA
Vout (V)
10
8
ZXTR2105
6
ZXTR2108
ZXTR2112
4
2
0
0
10
20
30
40
50
60
Input Voltage (V)
Figure 4 Input voltage VIN regulation
Issue 1.0 November 2015
www.diodes.com
© Diodes Incorporated, 2015
3
ZXTR21XXEV1
For a fixed input voltage of 24V, figure 5 shows the regulation of three output voltages as the
load current is swept. Load is applied to one output at a time.
Iout Vs Vout
14
12
Vout (V)
10
8
ZXTR2105
6
ZXTR2108
4
ZXTR2112
2
0
0
10
20
30
40
50
Output current (mA)
Figure 5 Output load regulation
PCB Layout
Top side
Issue 1.0 November 2015
www.diodes.com
© Diodes Incorporated, 2015
4
ZXTR21XXEV1
Bottom side
Issue 1.0 November 2015
www.diodes.com
© Diodes Incorporated, 2015
5
ZXTR21XXEV1
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements,
corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated
does not assume any liability arising out of the application or use of this document or any product described herein; neither
does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer
or user of this document or products described herein in such applications shall assume all risks of such use and will agree
to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website,
harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through
unauthorized sales channels. Should Customers purchase or use Diodes Incorporated products for any unintended or
unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless
against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product
names and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or
systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use
provided in the labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably
be expected to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support
devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support
devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by
Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any
damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2015, Diodes Incorporated
www.diodes.com
Issue 1.0 November 2015
www.diodes.com
© Diodes Incorporated, 2015
6