Veam VBN Connector Catalog

VBN Connectors
ITT VEAM
PROVEN QUALITY, RELIABILITY AND EXPERTISE.
ITT’s Interconnect Solutions’ Veam brand is
a leading global manufacturer of connector
products serving international customers in
multiple end markets.
In an increasingly global economy, getting
from Point A to Point B on time and on budget
is more important than ever. VEAM
connectors protect the world’s products and
people in transit so they can get to where
they’re going with maximum efficiency.
About ITT
ITT is a diversified leading manufacturer of highly engineered
critical components and customized technology solutions for
the energy, transportation and industrial markets. Building on its
heritage of innovation, ITT partners with its customers to deliver
enduring solutions to the key industries that underpin our modern
way of life. Founded in 1920, ITT is headquartered in White Plains,
N.Y., with employees in more than 35 countries and sales in a total
of approximately 125 countries. The company generated 2014
revenues of $2.7 billion. For more information, visit www.itt.com.
Engineered with your
toughest challenges in mind.
Dimensions shown in mm
Specifications and dimensions subject to change
2
www.ittcannon.com
VBN PRODUCT INTRODUCTION
•Crimp contacts are available in sizes 16, 12 and 8 AWG.
•The VBN connector series is based on MIL-DTL-5015G and
VG95234 specification. They are interchangeable with all
corresponding CIR/VG types and feature identical panel
mounting dimensions
•The stainless steel pins installed on the critical wear points
of the ramps, the dynamic coupling gasket at the base of
the plugshell, the flat and the wave washer between the
coupling nut and the plugshell, are the key features that
allow to prevents the unmating of the connection in case of
vibration and guarantees the high reliability of the bayonet
mating system.
•VBN connectors are available in 15 sizes arrangements from
shell size 16S to shell size 40 with arrangements having
from 4 up to 70 contacts.
Out of this range, 14 sizes arrangements are qualified to NF F 61-030 French specification and approved by SNCF and RATP (from 4 to 60 contacts).
•Environmental sealing of mated connectors to IP67 is
achieved by compression of the coupling gasket, while
integrity at the rear is achieved by the use of an individual
wire seal grommet with membranes (being penetrated only
when a wire is present) and use of appropriate accessories.
•The contact system enables easy insertion and removal.
The inserts are composed of a halogen free hard plastic
maternal that results in a very low fire hazard.
•Comprehensive range of screened / unscreened, sealed /
unsealed backshells & accessories
•Stainless steel bayonet pins riding along the three Bayonet
ramps (machined into the receptacle shell) achieve the
connector coupling. Coupling integrity is guaranteed by:
•Three stainless steel pins at the critical wear points of
the receptacle shell bayonet ramps
•An audible click when fully mated.
•Alignment of three yellow colored dots when
fully mated.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
3
TABLE OF CONTENTS
Technical information
5
Receptacle – 90 degrees
21
Components description
6
Plug – straight
26
Order code
7
Plug – 90 degrees
34
Version overview
8
Shielded connectors
39
Inserts arrangements
9
Spares backshells
43
Contacts – pin contacts
11
Accessories 50
Contacts – socket contacts
12
Application notes
58
Receptacle – straight
13
Dimensions shown in mm
Specifications and dimensions subject to change
4
www.ittcannon.com
VBN TECHNICAL INFORMATION
MATERIAL CONSTRUCTION
Shells: Aluminum alloy
Available Platings: T108: Black Zn/Co - 200 H Salt Spray - Conductive
T240: Blue Zn/Ni - 500 H Salt Spray - Conductive
T39: Black epoxyurhetanic coating - 500 H Salt Spray - Non Conductive
Insulator: Low fire hazard thermoplastic.
Interfacial Seal & Grommet: Low fire hazard silicone rubber
Contacts: Copper alloy with gold or silver (on request, not according
NFF standard) plating.
ENVIRONMENTAL PERFORMANCE
Operating Temperature: -40°C to +100°C per NF F 61-030
Corrosion Resistance: T108: Black Zn/Co - 200 H Salt Spray - Conductive
T240: Blue Zn/Ni - 500 H Salt Spray - Conductive
T39: Black epoxyurhetanic coating - 500 H Salt Spray - Non Conductive
Water Protection: IP67 in mated condition when used with proper
backshell and accessories
Fluid Resistance: Gas, oil, mineral oil, acid bath per NF F 61-030
Fire and smoke: - Rated I3F2 acc. to NFF 16-101 & 16 - 102 (exigence 2)
- Rated HL3 - R22/R23 acc. to EN 45545-2 (consult factory concerning HL3)
- UL94v0 compliant
MECHANICAL PERFORMANCE
Durability: 500 mating cycles minimum
Bayonet Coupling Torque: Per VG95234
Shock: 30g - 18 ms.
Vibration: 2g / 10-100Hz or 5g / 25-250Hz (NF F 60-002 / NF C 93-400).
Min. Retention force: 70N for contacts #16
of the contact in: 90N for contacts #12
the insulator: 110N for contacts #8
ELECTRICAL PERFORMANCE
Creepage/Clearance distance: 12mm / 8mm min. (In mated
conditions, interfacial seal in compression)
Contact Rating: See table
Insulation Resistance: 5000 MOhm
Rated voltage: 380Vac / 500Vdc per NF F 61-030
Withstanding Voltage: 3250 VAC rms per NF F 61-030
Rated Current (*) A
Contact Resistance
mΩ max.
Layout
Shell Size
Contacts Size
No of Contacts
Single cont.
Grouped cont.
16S-1
16S
16S
7
15
12
2.5
18-19
18
16
10
15
12
2.5
20-15
20
12
7
23
20
1.3
20-4
20
12
4
23
22
1.3
20-7
20
16
8
15
14
2.5
22-14
22
16
19
15
11,5
2.5
22-23
22
12
8
23
20
1.3
24-10
24
8
7
46
33
0.9
28-21
28
16
37
15
12
2.5
32A-13
32
12
13
23
18
1.3
36-10
36
16
48
15
7,5
2.5
36A-22
36
12
22
23
19
1.3
40A-35
40
12
35
23
15,5
1.3
40A-60
40
16
60
15
9
2.5
(*) Acc. To NF F 61-030. Max heating allowed: 50°C
- Single contact: loaded into insulator. - Grouped contacts: fully populated insulator, all contacts loaded.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
5
VBN COMPONENTS DESCRIPTION
PANEL MOUNTED CONNECTOR
Flange - holds the insert and incorporates an alignment key to position the insert.
The Flange accommodates either the socket or pin insert to reverse gender. Bayonet
Coupling ramps provide cam action for coupling and uncoupling with the plug
connectors. Stainless steel pins, at the top of the ramps, ensure positive locking and
long service life.
Insert (pin or socket) - Removable, orientable, retains the contacts and can be used
in either Flange or plugshells.
Contacts (pin or socket) - Suitable to be crimped with the wire conductors.
Circlip Retaining Ring - Retains the insert into the shell.
PLUG CONNECTOR
Coupling nut - Provides cam force when mating and un-mating mechanical system for
coupling and uncoupling of the connectors.
Plugshell - Holds the insert and incorporates an alignment key to position the insert.
The plugshell accommodates either the socket or pin insert to reverse gender.
Insert (pin or socket) - Removable, orientable, retains the contacts and can be used in
either Flange or plugshells.
Circlip Retaining Ring - Retains the insert into the shell.
Contacts (pin or socket) - Suitable to be crimped with the wire conductors
Dimensions shown in mm
Specifications and dimensions subject to change
6
www.ittcannon.com
VBN ORDER CODE
VBN
3
()
20
15
Connector Series
VBN
VEAM Bayonet
Coupling N Series
VBNG*Plug
Connector Type
2
Front Mounting Receptacle
3
Rear Mounting Receptacle
3890° Rear Mount Receptacle
6
Straight Plug Connector
890° Plug Connector
Connector Class
A, R
Straight or Right Angle, no Strain relief
AF, F, CF, CFZStraight or Right Angle with Strain relief
APG, RPG Straight for use with PG fitting
SS
Backshells for shielded cable
Shell Size
16S, 18, 20, 22, 24, 28, 32, 36, 40
Insert Arrangement
Refer to pages 9 and 10
Contact Gender
P
S
Male Contacts (Pin)
Female Contacts (Sockets)
Insert Orientation
NNormal
W, X, Y, Z Degree for alternate positions - refer to page 10
No Letter Insulation Not Installed
Shell Plating
TXX
See available platings page 5
Modification Code
Consult Factory
*To be used only with Connector Type ‘‘6’’ and Connector Class ‘‘SS’’
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
7
P
N
TXX
()
VBN VERSION OVERVIEW
RECEPTACLE
& PLUG
SEALING
STRAIGHT
VERSIONS
RECEPTACLE
& PLUG
SEALING
CLASS AV / RV
Short backshell
ext. thread
CLASS A / R
Standard backshell
ext. thread
VBN 2
Front Panel
CLASS A / R
Standard backshell
ext. thread
VBN 2
Front Panel
VBN3
Rear panel mounting
CLASS APG / RPG
Standard backshell int.
PG thread
VBN3
Rear panel mounting
With Grommet
X
Plug - VBN6
Without Grommet
90° VERSIONS
CLASS APG / RPG
Standard backshell int.
PG thread
With Grommet
X
CLASS AF / F
Standard backshell
with “A” cable clamp
Plug - VBN6
CLASS AF / F
Standard backshell
with “A” cable clamp
Without Grommet
CLASS CF / CFZ
Standard backshell
with “C” cable clamp
Plug - VBN6-GG
CLASS CF / CFZ
Standard backshell
with “C” cable clamp
Plug - VBN6-GG
CLASS SS / RSS
Backshell with
shielding system
CLASS SS / RSS
Backshell with
shielding system
Dimensions shown in mm
Specifications and dimensions subject to change
8
www.ittcannon.com
VBN INSERT ARRANGEMENTS
CONTACT LAYOUTS
Front View of the Male Insert
G
W
A
A
B
X
C
D
16S-1
VEA M
16S-1
18-19
20-4
7
10
4
Contact Size
16
16
12
A B
VEA M
E
Layout
C
Z
G
E
B
J
H
C
D
D
K
W
U
T
A
V
S
8
7
19
Contact Size
16
12
16
N
W
W
B
D
C
C
24-10
M
U
T
D
N
W
j
k
r
VEA M 28-21
22-23
24-10
28-21
# of contacts
8
7
37
Contact Size
12
8
16
www.ittcannon.com
9
Z
X
e
d
p
R
P
Layout
Dimensions shown in mm
Specifications and dimensions subject to change
J
H
V
h
n
C
c
b
g
N
f
m
s
Y
E
X
D
S
a
Y
E
E
Z
H
B
C
D
G
F
L
K
Z
G
F
B
A
E
A
F
A
R
22-14
# of contacts
W
B
22-1 4
20-15
N
N
P
F
G
VEA M
20-7
N
M
L
W
H
F N A
Z
X
F
N
Z Y
W
Layout
# of contacts
-7
20
G
Y
C 20- 4 B
Z
E
N
D
W
N
F
VBN INSERT ARRANGEMENTS
N
2
21
12
12
8
22
11
10
VEAM 17
5
m
Y
6
5
6
AM
v
36A-22
36-10
22
48
Contact Size
12
12
16
22
18
14
12
32
25
39
W
30
31
53
20
17
6
AM
59
36
6
21
40
17
16
12
67
66
56
55
57
41
18
11
13
70
40A-70
39
64
65
8
9
53
35
36
14
7
33
34
37
38
6
32
52
54
15
5
31
51
63
68
42
9
10
14
59
58
19
32
33
34
50
62
69
43
8
4
30
49
60
44
20
31
49
35
22
7
48
15
-35
30
58
50
Y
40A
57
47
16
7
8
46
37
45
5
29
48
61
3
29
Y
X
VE
22
23
9
28
56
VEA M
X
24
10
23
45
52
51
46
4
44
55
38
18
11
43
60
19
5
21
24
-
2
28
47
x
10
Z
4
35
33
3
26
Z
13
26
40
20
25
27
54
Z
W
19
29
34
25
41
21
3
27
42
27 N 1
26
2
W
17
1
Y
2
15
28
N
X
24
s
z 36
y
13
23
c
k
w
32A-13
1
j
r
Layout
N
b
h
# of contacts
16
U
a
q
p
u
t
VE
N
T
Z
g
f
n
7
8
S
Y
e
G
M
R
X
d
L
Y
9
Q
W
V
18
X
32A-13
X
4
19
4
7
16
K
P
O
B
F
E
J
H
W
W
3
VEA M 13
3
15
A
Z
9
D
C
20
Z
W
11
2
Z
Front View of the
Male Insert
N
14 N
1
13
1
X
10
Y
CONTACT ARRANGEMENTS
10
11
12
13
*not qualified according NF F standards
Layout
40A-35
# of contacts
35
60
70
Contact Size
12
16
16
KEYING SYSTEM
Insert Layout
Front view of male insert - Insert rotation
N
W
X
40A-60
Z
Y
16S-1
40A-70
Degrees for alternate positions
N
W
0
80
18-19
0
20-4
0
X
Y
Z
280
120
240
45
110
250
110
250
20-7
0
80
20-15
0
80
280
22-14
0
80
280
280
22-23
0
35
24-10
0
80
28-21
0
80
110
250
32A-13
0
65
130
230
295
36-10
0
80
125
235
280
250
280
280
36A-22
0
80
110
250
280
40A-35
0
70
130
230
290
40A-60
0
80
110
250
280
40A-70
0
80
110
250
280
Dimensions shown in mm
Specifications and dimensions subject to change
10
www.ittcannon.com
VBN CONTACTS
PIN CONTACTS
Male contact to be used on connector with
male insulator.
L
RETENTION
CLIP
D
C
B
D
C
B
A
A
L
RETENTION
CLIP
Shape type 1
Shape type 2
Wire Size
mm2
AWG
L
ØA
ØB
ØC
ØD
Cable O.D.
max. (2 - 3)
Type
20
28.1
1.58
1.2
2.6
3.9
3.8
1
16
28.1
1.58
2.0
2.9
3.9
3.8
1
2.5-3.0
12
28.1
1.58
2.5
3.8
3.8
3.8
1
0.5-0.75
20
33.2
1.58
1.2
2.6
3.9
3.8
1
1.0-2.0
16
33.2
1.58
2.0
2.9
3.9
3.8
1
2.5-3.0
12
33.2
1.58
2.5
3.8
3.8
3.8
1
Male Part number
Size
51513-16S-12T12
16S
0.5-0.75
51513-16S-20T12
16S
1.0-2.0
51513-16S-26T12
16S
51513-16-12T12
16
51513-16-20T12
16
51513-16-26T12
16
51513-12T12
12
2.5-3.0
12
38.5
2.38
2.5
3.8
5.5
5.4
1
51513-12-12T12
12
0.5-0.75
20
38.5
2.38
1.2
2.6
5.5
5.4
1
51513-12-20T12
12
1.0-2.0
16
38.5
2.38
2.0
3.8
5.5
5.4
1
51513-12-30T12
12
4.0
12
38.5
2.38
3.0
4.8
5.5
5.4
1
51513-12-38T12
12
6.0
10
38.5
2.38
3.6
4.8
5.5
5.4
1
51513-8T12
8
AWG 8
8
41.7
3.60
4.6
6.8
8.0
7.8
2
51513-8-20T12
8
1.0 – 2.0
41.7
3.60
2.0
3.8
8.0
7.8
2
51513-8-26T12
8
3.0
41.7
3.60
2.5
3.8
8.0
7.8
2
51513-8-30T12
8
4.0
41.7
3.60
3.0
4.8
8.0
7.8
2
51513-8-38T12
8
6.0
41.7
3.60
3.6
4.8
8.0
7.8
2
51513-8-50T12
8
10
41.7
3.60
5.0
7
8.0
7.8
2
NOTES: 1. Finish: Silver plating on size 12 and 8 also available (please consult factory).
2. The dimensions indicated are the maximum OD cable permitted, due to the rear insert holes.
3. When grommets are used refer to page 50 for cable dimensions.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
11
VBN CONTACTS
SOCKET CONTACTS
Female contact to be used on connector with
female insulator.
L
RETENTION
RING
Size
51511-16S-12T12
16S
0.5-0.75
51511-16S-20T12
16S
1.0-2.0
51511-16S-26T12
16S
51511-16-12T12
16
51511-16-20T12
16
51511-16-26T12
16
D
RETENTION
RING
Shape type 1
Female Part
number
C
B
D
C
B
A
A
L
Shape type 2
Wire Size
mm2
AWG
L
ØA
ØB
ØC
ØD
Cable O.D.
max. (2 - 3)
Type
20
28.1
1.58
1.2
2.6
3.9
3.8
1
16
28.1
1.58
2.0
2.9
3.9
3.8
1
2.5-3.0
12
28.1
1.58
2.5
3.8
3.8
3.8
1
0.5-0.75
20
33.2
1.58
1.2
2.6
3.9
3.8
1
1.0-2.0
16
33.2
1.58
2.0
2.9
3.9
3.8
1
2.5-3.0
12
33.2
1.58
2.5
3.8
3.8
3.8
1
51511-12T12
12
2.5-3.0
12
38.5
2.38
2.5
3.8
5.5
5.4
1
51511-12-12T12
12
0.5-0.75
20
38.5
2.38
1.2
2.6
5.5
5.4
1
51511-12-20T12
12
1.0-2.0
16
38.5
2.38
2.0
3.8
5.5
5.4
1
51511-12-30T12
12
4.0
12
38.5
2.38
3.0
4.8
5.5
5.4
1
51511-12-38T12
12
6.0
10
38.5
2.38
3.6
4.8
5.5
5.4
1
51511-8T12
8
AWG 8
8
41.7
3.60
4.6
6.8
8.0
7.8
2
51511-8-20T12
8
1.0 – 2.0
41.7
3.60
2.0
3.8
8.0
7.8
2
51511-8-26T12
8
3.0
41.7
3.60
2.5
3.8
8.0
7.8
2
51511-8-30T12
8
4.0
41.7
3.60
3.0
4.8
8.0
7.8
2
51511-8-38T12
8
6.0
41.7
3.60
3.6
4.8
8.0
7.8
2
51511-8-50T12
8
10
41.7
3.60
5.0
7
8.0
7.8
2
NOTES: 1. Finish: Silver plating on size 12 and 8 also available (please consult factory).
2. The dimensions indicated are the maximum OD cable permitted, due to the rear insert holes.
3. When grommets are used refer to page 50 for cable dimensions.
Dimensions shown in mm
Specifications and dimensions subject to change
12
www.ittcannon.com
VBN RECEPTACLE
VBN2-Front panel mounting receptacle with through
fixing holes and a threaded rear end.
Supplied without accessories
A
B
C
INSERT RETAINING
RING
E
F
D
G
F
THREAD V
E
SIZE
A
B
+0.4-0
C
±0.2
ØD
+0-0.15
E
±0.3
F
±0.1
ØG
Thread V
16S
40
18.2
3.2
27.4
32.5
24.6
3.2
7/8”-20 UNEF
18
50
23.05
4
30.8
35
27
3.2
1”-20 UNEF
20
50
23.05
4
34.2
38
29.4
3.2
1 1/8”-18 UNEF
22
50
23.05
4
37.4
41
31.8
3.2
1 1/4”-18 UNEF
24
50
23.05
4
40.9
44.5
34.9
3.7
1 3/8”-18 UNEF
28
50
24.05
4
46.7
50.8
39.7
3.7
1 5/8”-18 UNEF
32
50
24.05
4
53.4
57
44.5
4.3
1 7/8”-16 UN
36
50
24.05
4
59.6
63.5
49.2
4.3
2 1/16”-16 UN
40
50
24.05
4
65.5
69.9
55.5
4.3
2 5/16”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
13
VBN RECEPTACLE
VBN3-Rear panel mounting receptacle with threaded
fixing holes and a threaded rear end.
Supplied without accessories
A
C
B
INSERT RETAINING
RING
E
F
D
G
THREAD V
F
E
SIZE
A
B
+0.4-0
C
±0.2
ØD
+0-0.15
E
±0.3
F
±0.1
ØG
Thread V
16S
40
+0.4-0
3.2
27.4
32.5
24.6
M4
7/8”-20 UNEF
18
50
23.05
4
30.8
35
27
M4
1”-20 UNEF
20
50
23.05
4
34.2
38
29.4
M4
1 1/8”-18 UNEF
22
50
23.05
4
37.4
41
31.8
M4
1 1/4”-18 UNEF
24
50
23.05
4
40.9
44.5
34.9
M4
1 3/8”-18 UNEF
28
50
24.05
4
46.7
50.8
39.7
M5
1 5/8”-18 UNEF
32
50
24.05
4
53.4
57
44.5
M5
1 7/8”-16 UN
36
50
24.05
4
59.6
63.5
49.2
M5
2 1/16”-16 UN
40
50
24.05
4
65.5
69.9
55.5
M5
2 5/16”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
14
www.ittcannon.com
VBN RECEPTACLE
VBN3AV-VBN3RV-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a short straight backshell with UNEF
external thread.
Supplied with (RV) or without (AV) grommet.
L
B
A
C
F
G
D
E
H
G
THREAD V
F
SIZE
L
A
+0.4-0
B
±0.2
C
Min.
ØD
+0-0.15
ØE
Max.
F
±0.3
G
±0.1
ØH
Thread V
16S
55
18.2
3.2
10
27.4
16.2
32.5
24.6
M4
7/8”-20 UNEF
18
65
23.05
4
10
30.8
19
35
27
M4
1”-20 UNEF
20
70
23.05
4
10
34.2
22
38
29.4
M4
1 3/16”-18 UNEF
22
70
23.05
4
10
37.4
24.5
41
31.8
M4
1 3/16”-18 UNEF
24
70
23.05
4
10
40.9
27.8
44.5
34.9
M4
1 7/16”-18 UNEF
28
75
24.05
4
10
46.7
31.2
50.8
39.7
M5
1 7/16”-18 UNEF
32
75
24.05
4
12
53.4
37.8
57
44.5
M5
1 3/4”-18 UNS
36
80
24.05
4
12
59.6
45
63.5
49.2
M5
2 ”-18 UNS
40
80
24.05
4
12
65.5
51.2
69.9
55.5
M5
2 1/4”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
15
VBN RECEPTACLE
VBN3A-VBN3R-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a standard straight backshell with UNEF
external thread.
Supplied with (R) or without (A) grommet.
L
C
G
D
E
H
F
B
A
G
THREAD V
F
SIZE
L
A
+0.4-0
B
±0.2
C
Min.
ØD
+0-0.15
ØE
Max.
F
±0.3
G
±0.1
ØH
Thread V
16S
80
18.2
3.2
10
27.4
16.2
32.5
24.6
M4
7/8”-20 UNEF
18
100
23.05
4
10
30.8
19
35
27
M4
1”-20 UNEF
20
100
23.05
4
10
34.2
22
38
29.4
M4
1 3/16”-18 UNEF
22
100
23.05
4
10
37.4
24.5
41
31.8
M4
1 3/16”-18 UNEF
24
105
23.05
4
10
40.9
27.8
44.5
34.9
M4
1 7/16”-18 UNEF
28
105
24.05
4
10
46.7
31.2
50.8
39.7
M5
1 7/16”-18 UNEF
32
115
24.05
4
12
53.4
37.8
57
44.5
M5
1 3/4”-18 UNS
36
125
24.05
4
12
59.6
45
63.5
49.2
M5
2 ”-18 UNS
40
125
24.05
4
12
65.5
51.2
69.9
55.5
M5
2 1/4”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
16
www.ittcannon.com
VBN RECEPTACLE
VBN3AM-VBN3RM-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a standard straight backshell with
metric internal thread.
Supplied with (RM) or without (AM) grommet.
L
A
B
C
F
G
D
Thread V
H
G
F
SIZE
L
A
+0.4-0
B
±0.2
ØD
+0-0.15
F
±0.3
G
±0.1
ØH
Thread V
C Min
16S
80
18.2
3.2
27.4
32.5
24.6
M4
18
100
23.05
4
30.8
35
27
M4
12
15
15
18
20
100
23.05
4
34.2
38
29.4
M4
15
22
100
23.05
4
37.4
41
31.8
M4
15
24
105
23.05
4
40.9
44.5
34.9
M4
28
105
24.05
4
46.7
50.8
39.7
M5
18
15
18
15
20
32
115
24.05
4
53.4
57
44.5
M5
20
36
125
24.05
4
59.6
63.5
49.2
M5
20
40
125
24.05
4
65.5
69.9
55.5
M5
20
For additional thread size please consult the factory.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
17
Metric
M12x1.5
M16x1.5
M20x1.5
M16x1.5
M20x1.5
M25x1.5
M32x1.5
M16x1.5
M20x1.5
M25x1.5
M20x1.5
M25x1.5
M32x1.5
M25x1.5
M32x1.5
M20x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M32x1.5
M40x1.5
M50x1.5
M25x1.5
M32x1.5
M40x1.5
M50x1.5
M63x1.5
VBN RECEPTACLE
VBN3APG-VBN3RPG-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a standard straight backshell with
PG internal thread.
Supplied with (RPG) or without (APG) grommet.
L
A
B
C
F
G
D
Thread V
H
G
F
SIZE
L
A
+0.4-0
B
±0.2
ØD
+0-0.15
F
±0.3
G
±0.1
ØH
Thread V
16S
80
18.2
3.2
27.4
32.5
24.6
M4
C Min
13
18
100
23.05
4
30.8
35
27
M4
15
20
100
23.05
4
34.2
38
29.4
M4
15
22
100
23.05
4
37.4
41
31.8
M4
15
24
105
23.05
4
40.9
44.5
34.9
M4
15
20
28
105
24.05
4
46.7
50.8
39.7
M5
15
32
115
24.05
4
53.4
57
44.5
M5
20
36
125
24.05
4
59.6
63.5
49.2
M5
20
40
125
24.05
4
65.5
69.9
55.5
M5
20
C Min
PG9
PG16
PG21
PG16
PG29
PG16
PG29
PG21
PG29
PG36
PG21
PG29
PG29
PG36
PG36
PG42
PG36
PG42
For additional thread size please consult the factory.
Dimensions shown in mm
Specifications and dimensions subject to change
18
www.ittcannon.com
VBN RECEPTACLE
VBN3AF-VBN3F-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a standard straight backshell
and a cable clamp with bushing for
single wires.
Supplied with (F) or without (AF) grommet.
L
B
G
D
F
H
E
A
G
F
SIZE
L
A
+0.4-0
B
±0.2
ØD
+0-0.15
ØE (*)
Max.
F
±0.3
G
±0.1
ØH
16S
105
18.2
3.2
27.4
11
32.5
24.6
M4
18
125
23.05
4
30.8
14.2
35
27
M4
20
125
23.05
4
34.2
15.8
38
29.4
M4
22
125
23.05
4
37.4
15.8
41
31.8
M4
24
130
23.05
4
40.9
19
44.5
34.9
M4
28
130
24.05
4
46.7
19
50.8
39.7
M5
32
145
24.05
4
53.4
23.8
57
44.5
M5
36
155
24.05
4
59.6
31.7
63.5
49.2
M5
40
167
24.05
4
65.5
34.9
69.9
55.5
M5
(*): Maximum cable (or wires bundle dimension) outer diameter
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
19
VBN RECEPTACLE
VBN3CF-VBN3CFZ-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a standard straight backshell
and a cable clamp for jacketed cable.
Supplied with (CFZ) or without (CF) grommet.
L
B
G
D
F
H
E
A
G
F
SIZE
L
A
+0.4-0
B
±0.2
ØD
+0-0.15
ØE (*)
F
±0.3
G
±0.1
ØH
24.6
M4
Min
Max
8
13.5
32.5
16S
110
18.2
3.2
27.4
18
135
23.05
4
30.8
9.6
15.8
35
27
M4
20
135
23.05
4
34.2
11.3
19
38
29.4
M4
22
135
23.05
4
37.4
11.3
19
41
31.8
M4
24
140
23.05
4
40.9
15.5
23.8
44.5
34.9
M4
28
140
24.05
4
46.7
15.5
23.8
50.8
39.7
M5
32
160
24.05
4
53.4
23.4
31.7
57
44.5
M5
36
175
24.05
4
59.6
23.4
35
63.5
49.2
M5
40
175
24.05
4
65.5
29.9
41.2
69.9
55.5
M5
(*): cable outer diameter range.
Dimensions shown in mm
Specifications and dimensions subject to change
20
www.ittcannon.com
VBN RECEPTACLE
VBN38A-VBN38R-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a 90° backshell with UNEF external thread.
Supplied with (R) or without (A) grommet.
F
L
G
B
A
F
I
E
G
D
H
THREAD V
C
SIZE
L
A
+0.4-0
B
±0.2
ØC.
ØD
+0-0.15
E
F
±0.3
G
±0.1
ØH
I
Min.
Thread V
16S
63
18.2
3.2
14.7
27.4
30
32.5
24.6
M4
10
7/8”-20 UNEF
18
75
23.05
4
17.2
30.8
35
35
27
M4
10
1”-20 UNEF
20
80
23.05
4
20.35
34.2
35
38
29.4
M4
10
1 3/16”-18 UNEF
22
80
23.05
4
23
37.4
35
41
31.8
M4
10
1 3/16”-18 UNEF
24
80
23.05
4
25.8
40.9
40
44.5
34.9
M4
10
1 7/16”-18 UNEF
28
80
24.05
4
28.7
46.7
40
50.8
39.7
M5
10
1 7/16”-18 UNEF
32
85
24.05
4
36.5
53.4
45
57
44.5
M5
12
1 3/4”-18 UNS
36
90
24.05
4
42.6
59.6
50
63.5
49.2
M5
12
2 ”-18 UNS
40
95
24.05
4
48.6
65.5
55
69.9
55.5
M5
12
2 1/4”-16 UN
The connectors are supplied with an adapter between the flange and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
21
VBN RECEPTACLE
VBN38AM-VBN38RM-Rear panel mounting receptacle with threaded fixing holes.
Foresees a 90° backshell with an adapter with metric
internal thread.
Supplied with (RM) or without (AM) grommet.
L
F
G
B
A
F
C
E
G
D
H
THREAD V
SIZE
L
A
+0.4-0
B
±0.2
ØD
+0-0.15
E
F
±0.3
G
±0.1
ØH
Thread V
C Min
12
16S
63
18.2
3.2
27.4
52
32.5
24.6
M4
18
75
23.05
4
30.8
57
35
27
M4
15
20
80
23.05
4
34.2
57
38
29.4
M4
15
22
80
23.05
4
37.4
57
41
31.8
M4
15
24
80
23.05
4
40.9
65
44.5
34.9
M4
28
80
24.05
4
46.7
65
50.8
39.7
M5
32
85
24.05
4
53.4
70
57
44.5
M5
20
36
90
24.05
4
59.6
78
63.5
49.2
M5
20
40
95
24.05
4
65.5
80
69.9
55.5
M5
20
15
18
18
15
18
20
15
18
20
Metric
M12x1.5
M16x1.5
M20x1.5
M16x1.5
M20x1.5
M25x1.5
M20x1.5
M25x1.5
M32x1.5
M20x1.5
M25x1.5
M32x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M32x1.5
M40x1.5
M50x1.5
M40x1.5
M50x1.5
M63x1.5
The connectors are supplied with an adapter between the flange and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
22
www.ittcannon.com
VBN RECEPTACLE
VBN38APG-VBN38RPG-Rear panel mounting receptacle with threaded fixing holes.
Foresees a 90° backshell with an adapter with PG
internal thread.
Supplied with (RPG) or without(APG) grommet.
L
F
G
B
A
F
C
E
G
D
H
THREAD V
SIZE
L
A +0.4-0
B ±0.2
ØD +0-0.15
F ±0.3
E
G ±0.1
ØH
C Min
PG
16S
63
18.2
3.2
27.4
32.5
48
24.6
M4
14
18
75
23.05
4
30.8
35
54
27
M4
14
20
80
23.05
4
34.2
38
53
29.4
M4
22
80
23.05
4
37.4
41
53
31.8
M4
24
80
23.05
4
40.9
44.5
34.9
M4
PG9
PG16
PG21
PG16
PG29
PG16
PG29
PG21
PG29
PG36
PG21
PG29
PG36
PG29
PG36
PG36
PG42
PG42
PG48
58
69
28
80
24.05
4
46.7
50.8
32
85
24.05
4
53.4
57
36
90
24.05
4
59.6
63.5
40
95
24.05
4
65.5
69.9
58
69
60
71
www.ittcannon.com
23
15
13
15
13
13
15
39.7
M5
13
15
44.5
M5
15
68
49.2
M5
15
74
76
55.5
M5
15
The connectors are supplied with an adapter between the flange and the elbow. For additional thread size please consult the factory.
Dimensions shown in mm
Specifications and dimensions subject to change
Thread V
VBN RECEPTACLE
VBN38AF-VBN38F-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a 90° backshell and a cable clamp with
bushing for single wires.
Supplied with (F) or without (AF) grommet.
F
L
G
B
A
F
I
G
D
H
C
E
SIZE
L
A
+0.4-0
B
±0.2
ØC (*)
Max.
ØE
+0-0.15
E Max.
F
±0.3
G
±0.1
ØH
I
16S
63
18.2
3.2
11
27.4
30
32.5
24.6
M4
45
18
75
23.05
4
14.2
30.8
32.2
35
27
M4
53
20
80
23.05
4
15.8
34.2
37.5
38
29.4
M4
53
22
80
23.05
4
15.8
37.4
37.5
41
31.8
M4
53
24
80
23.05
4
19
40.9
43.3
44.5
34.9
M4
58
28
80
24.05
4
19
46.7
43.3
50.8
39.7
M5
58
32
85
24.05
4
23.8
53.4
51.7
57
44.5
M5
66
36
90
24.05
4
31.7
59.6
58
63.5
49.2
M5
69
40
95
24.05
4
34.9
65.5
68.5
69.9
55.5
M5
95
(*): Maximum cable (or wires bundle dimension) outer diameter. The connectors are supplied with an adapter between the flange and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
24
www.ittcannon.com
VBN RECEPTACLE
VBN38CF-VBN38CFZ-Rear panel mounting receptacle with threaded
fixing holes.
Foresees a 90° backshell and a cable clamp
for jacketed cable.
Supplied with (CFZ) or without (CF) grommet.
L
F
G
B
A
F
I
G
D
H
C
E
SIZE
L
A
+0.4-0
B
±0.2
16S
63
18.2
3.2
18
75
23.05
20
80
23.05
22
80
24
80
28
32
ØC (*)
ØD
+0-0.15
E Max.
F±0.3
G
±0.1
ØH
I
28.1
32.5
24.6
M4
61
Min
Max
8
13.5
27.4
4
9.6
15.8
30.8
31
35
27
M4
68
4
11.3
19
34.2
37.3
38
29.4
M4
68
23.05
4
11.3
19
37.4
37.3
41
31.8
M4
68
23.05
4
15.5
23.8
40.9
42
44.5
34.9
M4
76
80
24.05
4
15.5
23.8
46.7
42
50.8
39.7
M5
76
85
24.05
4
23.4
31.7
53.4
54
57
44.5
M5
97
36
90
24.05
4
23.4
35
59.6
57.1
63.5
49.2
M5
98
40
95
24.05
4
29.9
41.2
65.5
63.5
69.9
55.5
M5
103
(*): cable outer diameter range. The connectors are supplied with an adapter between the flange and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
25
VBN PLUG
VBN6-Plug connector with standard coupling nut.
Foresees a threaded rear end.
Supplied without accessories
B
A
INSERT RETAINING
RING
THREAD V
SIZE
A
ØB Max.
Thread V
16S
18
40
32
7/8”-20 UNEF
50
36.5
1”-20 UNEF
20
50
39.9
1 1/8”-18 UNEF
22
50
43.1
1 1/4”-18 UNEF
24
50
46.6
1 3/8”-18 UNEF
28
50
53.4
1 5/8”-18 UNEF
32
50
60.1
1 7/8”-16 UN
36
50
66.3
2 1/16”-16 UN
40
50
72.5
2 5/16”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
26
www.ittcannon.com
VBN PLUG
MGPVBN6-Plug connector with rubber covered coupling nut.
Foresees a threaded rear end.
Supplied without accessories
B
A
C
INSERT RETAINING
RING
THREAD V
SIZE
A
ØB
ØC
Thread V
16S
40
44
38.9
7/8”-20 UNEF
18
50
49
43.5
1”-20 UNEF
20
50
51.5
46
1 1/8”-18 UNEF
22
50
56
50.5
1 1/4”-18 UNEF
24
50
60
54
1 3/8”-18 UNEF
28
50
67
61
1 5/8”-18 UNEF
32
50
76
67.6
1 7/8”-16 UN
36
50
82.3
74.3
2 1/16”-16 UN
40
50
88
80
2 5/16”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
27
VBN PLUG
VBN6AV-VBN6RV-Plug connector with standard coupling nut.
Foresees a short straight backshell with
UNEF external thread.
Supplied with (RV) or without (AV) grommet.
L
A
B
C
THREAD V
SIZE
L
ØA Max.
ØB Max.
C Min.
Thread V
16S
18
55
32
16.2
10
7/8”-20 UNEF
65
36.5
19
10
1”-20 UNEF
20
70
39.9
22
10
1 3/16”-18 UNEF
22
70
43.1
24.5
10
1 3/16”-18 UNEF
24
70
46.6
27.8
10
1 7/16”-18 UNEF
28
75
53.4
31.2
10
1 7/16”-18 UNEF
32
75
60.1
37.8
12
1 3/4”-18 UNS
36
80
66.3
45
12
2 ”-18 UNS
40
80
72.5
51.2
12
2 1/4”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
28
www.ittcannon.com
VBN PLUG
VBN6A-VBN6R-Plug connector with standard coupling nut.
Foresees a standard straight backshell with UNEF
external thread.
Supplied with (R) or without (A) grommet.
A
L
B
C
THREAD V
SIZE
L
ØA Max.
ØB Max.
C Min.
Thread V
16S
80
32
16.2
10
7/8”-20 UNEF
18
100
36.5
19
10
1”-20 UNEF
20
100
39.9
22
10
1 3/16”-18 UNEF
22
100
43.1
24.5
10
1 3/16”-18 UNEF
24
105
46.6
27.8
10
1 7/16”-18 UNEF
28
105
53.4
31.2
10
1 7/16”-18 UNEF
32
115
60.1
37.8
12
1 3/4”-18 UNS
36
125
66.3
45
12
2 ”-18 UNS
40
125
72.5
51.2
12
2 1/4”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
29
VBN PLUG
VBN6AM-VBN6RM-Plug connector with standard coupling nut.
Foresees a standard straight backshell with metric
internal thread.
Supplied with (RM) or without (AM)t grommet.
A
L
THREAD V
C
SIZE
L
ØA Max.
16S
80
32
18
100
36.5
Thread V
C Min
Metric
12
M12x1.5
M16x1.5
M20x1.5
M16x1.5
M20x1.5
M25x1.5
M32x1.5
M16x1.5
M20x1.5
M25x1.5
M20x1.5
M25x1.5
M32x1.5
M25x1.5
M32x1.5
M20x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M32x1.5
M40x1.5
M50x1.5
M25x1.5
M32x1.5
M40x1.5
M50x1.5
M63x1.5
15
15
18
20
100
39.9
22
100
43.1
24
105
46.6
28
105
53.4
32
115
60.1
20
36
125
66.3
20
40
125
72.5
20
15
15
18
15
18
15
15
20
For additional thread size please consult the factory.
Dimensions shown in mm
Specifications and dimensions subject to change
30
www.ittcannon.com
VBN PLUG
VBN6APG-VBN6RPG-Plug connector with standard coupling nut.
Foresees a standard straight backshell with
PG internal thread.
Supplied with (RPG) or without (APG) grommet.
A
L
THREAD V
C
SIZE
L
ØA Max.
Thread V
C Min
PG
16S
80
32
13
PG9
18
100
36.5
15
PG16
15
PG21
20
100
39.9
15
PG16
15
PG29
22
100
43.1
15
PG16
15
PG29
15
PG21
15
PG29
24
105
46.6
20
PG36
PG21
28
105
53.4
15
15
PG29
32
115
60.1
20
PG29
20
PG36
36
125
66.3
20
PG36
20
PG42
40
125
72.5
20
PG36
20
PG42
For additional thread size please consult the factory.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
31
VBN PLUG
VBN6AF-VBN6F-Plug connector with standard coupling nut.
Foresees a standard straight backshell and a cable
clamp with bushing for single wires.
Supplied with (F) or without (AF) grommet.
A
B
L
SIZE
L
ØA Max.
ØB (*) Max.
16S
105
32
11
18
125
36.5
14.2
20
125
39.9
15.8
22
125
43.1
15.8
24
130
46.6
19
28
130
53.4
19
32
145
60.1
23.8
36
155
66.3
31.7
40
167
72.5
34.9
(*): Maximum cable (or wires bundle dimension) outer diameter The connectors are supplied with an adapter between the flange and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
32
www.ittcannon.com
VBN PLUG
VBN6CF-VBN6CFZ-Plug connector with standard coupling nut.
Foresees a standard straight backshell and a cable
clamp for jacketed cable.
Supplied with (CFZ) or without (CF) grommet.
L
B
A
SIZE
L
ØA Max.
ØB (*)
Min
Max.
16S
110
32
8
13.5
18
135
36.5
9.6
15.8
20
135
39.9
11.3
19
22
135
43.1
11.3
19
24
140
46.6
15.5
23.8
28
140
53.4
15.5
23.8
32
160
60.1
23.4
31.7
36
175
66.3
23.4
35
40
175
72.5
29.9
41.2
(*): cable outer diameter range.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
33
VBN PLUG
VBN8A-VBN8R-Plug connector with standard coupling nut.
Foresees a 90° backshell with UNEF external thread.
Supplied with (R) or without (A) grommet.
A
D
B
L
THREAD
C
SIZE
L
ØA Max.
B
ØC Max.
D Min.
Thread V
16S
18
63
32
30
14.7
10
7/8”-20 UNEF
75
36.5
35
17.2
10
1”-20 UNEF
20
80
39.9
35
20.35
10
1 3/16”-18 UNEF
22
80
43.1
35
23
10
1 3/16”-18 UNEF
24
80
46.6
40
25.8
10
1 7/16”-18 UNEF
28
80
53.4
40
28.7
10
1 7/16”-18 UNEF
32
85
60.1
45
36.5
12
1 3/4”-18 UNS
36
90
66.3
50
42.6
12
2 ”-18 UNS
40
95
72.5
55
48.6
12
2 1/4”-16 UN
The connectors are supplied with an adapter between the plugshell and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
34
www.ittcannon.com
VBN PLUG
VBN8AM-VBN8RM-Plug connector with standard coupling nut.
Foresees a 90° backshell with metric internal thread.
Supplied with (RM) or without (AM) grommet.
A
C
B
L
THREAD V
SIZE
L
ØA Max.
B
Thread V
Min
12
16S
63
32
52
18
75
36.5
57
20
80
39.9
57
22
80
43.1
57
24
80
46.6
65
28
80
53.4
65
32
85
60.1
70
20
36
90
66.3
78
20
40
95
72.5
80
20
15
15
15
18
15
18
15
18
20
15
18
20
The connectors are supplied with an adapter between the plugshell and the elbow. For additional thread size please consult the factory.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
35
Max.
M12x1.5
M16x1.5
M20x1.5
M16x1.5
M20x1.5
M25x1.5
M20x1.5
M25x1.5
M32x1.5
M20x1.5
M25x1.5
M32x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M32x1.5
M40x1.5
M50x1.5
M40x1.5
M50x1.5
M63x1.5
VBN PLUG
VBN8APG-VBN8RPG-Plug connector with standard coupling nut.
Foresees a 90° backshell with PG internal thread.
Supplied with (RPG) or without (APG) grommet.
A
C
B
L
THREAD V
SIZE
L
ØA Max.
B
16S
63
32
48
18
75
36.5
54
20
80
39.9
53
22
80
43.1
53
24
80
46.6
28
80
53.4
32
85
60.1
36
90
66.3
Thread V
C Min
14
14
14
15
13
15
13
58
13
69
15
58
13
69
60
71
15
68
15
15
74
15
76
The connectors are supplied with an adapter between the plugshell and the elbow. For additional thread size please consult the factory.
40
95
72.5
PG
PG9
PG16
PG21
PG16
PG29
PG16
PG29
PG21
PG29
PG36
PG21
PG29
PG36
PG29
PG36
PG36
PG42
PG42
PG48
Dimensions shown in mm
Specifications and dimensions subject to change
36
www.ittcannon.com
VBN PLUG
VBN8AF-VBN8F-Plug connector with standard coupling nut.
Foresees a 90° backshell and a cable clamp with
bushing for single wires.
Supplied with (F) or without (AF) grommet.
A
B
L
C
D
SIZE
L
ØA Max.
B
ØC (*) Max.
D Max.
16S
63
32
45
11
30
18
75
36.5
53
14.2
32.2
20
80
39.9
53
15.8
37.5
22
80
43.1
53
15.8
37.5
24
80
46.6
58
19
43.3
28
80
53.4
58
19
43.3
32
85
60.1
66
23.8
51.7
36
90
66.3
69
31.7
58
40
95
72.5
95
34.9
68.5
(*): Maximum cable (or wires bundle dimension) outer diameter The connectors are supplied with an adapter between the plugshell and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
37
VBN PLUG
VBN8CF-VBN8CFZ-Plug connector with standard coupling nut.
Foresees a 90° backshell and a cable clamp for
jacketed cable.
Supplied with (CFZ) or without (CF) grommet.
A
B
L
C
D
SIZE
16S
L
63
ØA Max.
32
B
61
ØC (*)
D Max.
Min
Max.
8
13.5
28.1
18
75
36.5
68
9.6
15.8
31
20
80
39.9
68
11.3
19
37.3
22
80
43.1
68
11.3
19
37.3
24
80
46.6
76
15.5
23.8
42
28
80
53.4
76
15.5
23.8
42
32
85
60.1
97
23.4
31.7
54
36
90
66.3
98
23.4
35
57.1
40
95
72.5
103
29.9
41.2
63.5
(*): cable outer diameter range. The connectors are supplied with an adapter between the plugshell and the elbow.
Dimensions shown in mm
Specifications and dimensions subject to change
38
www.ittcannon.com
VBN SHIELDED CONNECTORS
VBN SS-This version is available on both plug and receptacle, in straight and
90° version. The plugs foresees a RFI spring on the plug-shell to
improve the shielding performances.
Termination of shielded cables is necessary to provide RFI/EMI
shielding protection. The VBN Connector series foresees a special
version to connect cable shielding braid to the connector backshell and
to guarantee the RFI/EMI immunity.
VBN3SS—
Rear mounting receptacle with straight
shielded backshell without grommet
VBN3RSS-Rear mounting receptacle with straight
shielded backshell with grommet
VBN38SS—
Rear mounting receptacle with 90° shielded backshell
without grommet
VBN38RSS-Rear mounting receptacle with 90° shielded backshell
with grommet
VBNG6SS—
Plug with straight shielded backshell without grommet
VBNG6RSS-Plug with straight shielded backshell with grommet
VBNG8SS—
Plug with 90° shielded backshell without grommet
VBNG8RSS-Plug with 90° shielded backshell with grommet
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
39
VBN SHIELDED CONNECTORS
VBN SS-The connector type SS are supplied with the accessories necessary to
connect the braid of the cable to the connector shells.
BRAID SOCK
KNIT MESH
METALLIC TIE BAND
The cable braid is connected to the rear knurled area of the backshell
and clamped by using the metallic tie band.
If case the cable braid cannot be directly connected to the shell, it is
possible to use the supplied braid sock to create a “bridge” between
the cable braid and the shell; a second tie-band must be used to fix the
braid sock to the cable (see below picture).
The SS system offers the possibility to connect more than one cable;
in this case the braids of the cable must be wrapped together using
the knit mesh to form a round shape.
The rear adapter protects the shielding area and it is available with
many type of termination to guarantee sealing.
Dimensions shown in mm
Specifications and dimensions subject to change
40
www.ittcannon.com
VBN SHIELDED CONNECTORS
VBN SS-The connector type SS are very flexible, offering
a wide range of size and termination type.
VBN CONN.
SIZE
BACKSHELL
ADAPTER
Shielding System
Inner Thread
SS Size
DIAM. B
Max.
04
8.4
05
06
04
05
06
13.5
16.5
8.4
13.5
16.5
05
13.5
06
16.5
05
16.5
06
19
08
19
10
24
PG21
PG29
28
08
10
12
19
24
31.2
PG21
PG29
PG36
32
12
31.2
PG36
13
14
14
36.5
42
42
PG42
PG48
16S
18
20
22
24
36
40
CABLE CLAMP
Type MGS
Cable Range
02
03R
03
05
03R
04
05
5-8
7-9
9 - 12
13 - 16
7-9
11 - 14
13 - 16
M16
M20
M25
M16
M20
M25
M20
M25
M32
04
11 - 14
-8
8 - 13.5
05
13 - 16
-10
9.5 - 15.8
05
13 - 16
-10
9.5 - 15.8
06
15 - 17.5
-12
11.3 - 19
06
15 - 17.5
-12
11.3 - 19
07
18 - 23.5
-16
15.5 - 23.8
M20
M25
M32
06
07
-
15 - 17.5
18 - 23.5
-
-12
-16
-20
11.3 - 19
15.5 - 23.8
23.4 - 31.7
M32
M40
M50
M63
M63
-
-
-20
23.4 - 31.7
-
-
-24
-28
-28
23.4 - 35
29.9 - 41.2
29.9 - 41.2
PG Thread
Metric Thread
PG11
PG16
M12
M16
M20
PG11
PG16
M12
M16
M20
PG16
PG21
PG16
PG21
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
Type VE3057 “A” & “C”
Cable
Clamp Size
41
Cable
Clamp Size
Cable Range
-4
2.5 - 8
-6
6.3 - 11
-10
-6
-8
-10
9.6 - 15.8
6.3 - 11
8 - 13.5
9.5 - 15.8
VBN SHIELDED CONNECTORS
VBN SS-Shielded connector part number description
SS04-
16S-1
P
N
T108
WIRE GROMMET
SHIELDING SYSTEM SIZE
INSERT LAYOUT
GENDER
INSERT ORIENTATION
SHELLS PLATING
CONNECTORS TYPE
-VO
-M25F
REAR TERMINATION
R
CONTACTS
VBNG6
CONNECTOR TYPE
Below is an example of how a complete connector part number is
generated from available options.
INSERT ORIENTATION
See page 10
VBN3: Rear mounting receptacle
VBN38: Rear mounting 90° receptacle
VBNG6: straight plug with shielding spring
VBNG8: 90° plug with shielding spring
SHELL PLATING
T108: Black Zinc/Cobalt
T240: Blue Zn/Ni
WIRE GROMMET
CONTACTS OPTIONS
R: grommet supplied
NONE: without grommet
VO: without contacts
SHIELDING SYSTEM SIZE
REAR TERMINATION
See table page 41
M25F: Internal metric thread
PG011: Internal PG thread
MGS04: MGS cable clamp
12C: Type “C” cable clamp
INSERT LAYOUT
See pages 9-10
GENDER
P: male contacts
S: female contacts
Dimensions shown in mm
Specifications and dimensions subject to change
42
www.ittcannon.com
VBN SPARE BACKSHELLS
VBN-RV-Short straight backshell with UNEF external thread.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
B
A
D
THREAD F
E
THREAD C
Part number
Shell size
ØA max
B ± 0.2
Thread C
Ø D ± 0.2
E Min.
Thread F
VBN-RV16STXX
VBN-RV18TXX
16S
26
30.5
7/8”- 20 UNEF
14
9.5
7/8”- 20 UNEF
18
29.5
38
1”- 20 UNEF
17
9.5
1”- 20 UNEF
VBN-RV20TXX
20
33
40
1 3/16”-18 UNEF
21
9.5
1 1/8”-18 UNEF
VBN-RV22TXX
22
36
40
1 3/16”-18 UNEF
21
9.5
1 1/4”-18 UNEF
VBN-RV24TXX
24
40
40
1 7/16”-18 UNEF
26
9.5
1 3/8”-18 UNEF
VBN-RV28TXX
28
46
45
1 7/16”-18 UNEF
26
9.5
1 5/8”-18 UNEF
VBN-RV32TXX
32
51.5
45
1 3/4”-18 UNS
32
11
1 7/8”-16 UN
VBN-RV36TXX
36
58
50
2”-18 UNS
37
11.8
2 1/16”-16 UN
VBN-RV40TXX
40
64.5
50
2 1/4”-16 UN
45
11.8
2 5/16”-16 UN
Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
43
VBN SPARE BACKSHELLS
VBN-R-Standard straight backshell with UNEF external thread.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
A
B
D
THREAD F
E
THREAD C
Part number
Shell size
ØA max
B ± 0.2
Thread C
Ø D ± 0.2
E Min.
Thread F
VBN-R16STXX
16S
26
55
7/8”- 20 UNEF
14
9.5
7/8”- 20 UNEF
VBN-R18TXX
18
29.5
70
1”- 20 UNEF
17
9.5
1”- 20 UNEF
VBN-R20TXX
20
33
70
1 3/16”-18 UNEF
21
9.5
1 1/8”-18 UNEF
VBN-R22TXX
22
36
70
1 3/16”-18 UNEF
21
9.5
1 1/4”-18 UNEF
VBN-R24TXX
24
40
75
1 7/16”-18 UNEF
26
9.5
1 3/8”-18 UNEF
VBN-R28TXX
28
46
75
1 7/16”-18 UNEF
26
9.5
1 5/8”-18 UNEF
VBN-R32TXX
32
51.5
85
1 3/4”-18 UNS
32
11
1 7/8”-16 UN
VBN-R36TXX
36
58
95
2”-18 UNS
37
11.8
2 1/16”-16 UN
VBN-R40TXX
40
64.5
95
2 1/4”-16 UN
45
11.8
2 5/16”-16 UN
Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
44
www.ittcannon.com
VBN SPARE BACKSHELLS
VBN-M-Standard straight backshell with metric internal thread.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
D1
THREAD F
THREAD C
L1
Ordering Part Number
Shell Size
D1 max
L1 ± 0,2
Thread C
Thread F
VBN-M12BL16STXX
VBN-M16BL16STXX
VBN-M20BL16STXX
VBN-M16BL18TXX
VBN-M20BL18TXX
VBN-M25BL18TXX
VBN-M32BL18TXX
VBN-M16BL20TXX
VBN-M20BL20TXX
VBN-M25BL20TXX
VBN-M20BL22TXX
VBN-M25BL22TXX
VBN-M32BL22TXX
VBN-M25BL24TXX
VBN-M32BL24TXX
VBN-M20BL28TXX
VBN-M25BL28TXX
VBN-M32BL28TXX
VBN-M40BL28TXX
VBN-M25BL32TXX
VBN-M32BL32TXX
VBN-M40BL32TXX
VBN-M32BL36TXX
VBN-M40BL36TXX
VBN-M50BL36TXX
VBN-M25BL40TXX
VBN-M32BL40TXX
VBN-M40BL40TXX
VBN-M50BL40TXX
VBN-M63BL40TXX
16S
16S
16S
18
18
18
18
20
20
20
22
22
22
24
24
28
28
28
28
32
32
32
36
36
36
40
40
40
40
40
28
26
28
29.5
29.5
29.5
34
33
33
33
36
36
36
40
43
46
46
46
46
51.5
51.5
54
58
58
58
64.5
64.5
64.5
64.5
64.5
55
55
55
70
70
70
70
70
70
70
70
70
70
75
75
75
75
75
75
85
85
85
95
95
95
95
95
95
95
95
M12x1.5
M16x1.5
M20x1.5
M16x1.5
M20x1.5
M25x1.5
M32x1.5
M16x1.5
M20x1.5
M25x1.5
M20x1.5
M25x1.5
M32x1.5
M25x1.5
M32x1.5
M20x1.5
M25x1.5
M32x1.5
M40x1.5
M25x1.5
M32x1.5
M40x1.5
M32x1.5
M40x1.5
M50x1.5
M25x1.5
M32x1.5
M40x1.5
M50x1.5
M63x1.5
7/8”- 20 UNEF
7/8”- 20 UNEF
7/8”- 20 UNEF
1”- 20 UNEF
1”- 20 UNEF
1”- 20 UNEF
1”- 20 UNEF
1 1/8”-18 UNEF
1 1/8”-18 UNEF
1 1/8”-18 UNEF
1 1/4”-18 UNEF
1 1/4”-18 UNEF
1 1/4”-18 UNEF
1 3/8”-18 UNEF
1 3/8”-18 UNEF
1 5/8”-18 UNEF
1 5/8”-18 UNEF
1 5/8”-18 UNEF
1 5/8”-18 UNEF
1 7/8”-16 UN
1 7/8”-16 UN
1 7/8”-16 UN
2 1/16”-16 UN
2 1/16”-16 UN
2 1/16”-16 UN
2 5/16”-16 UN
2 5/16”-16 UN
2 5/16”-16 UN
2 5/16”-16 UN
2 5/16”-16 UN
For additional thread size please consult the factory. Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
45
VBN SPARE BACKSHELLS
VBN-PG-Standard straight backshell with PG internal thread.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
D1
THREAD F
THREAD C
L1
Ordering Part Number
Shell Size
D1 max
L1 ± 0,2
Thread C
Thread F
VBN-PG9BL16STXX
16S
26
55
PG9
7/8”- 20 UNEF
VBN-PG16BL18TXX
18
29.5
70
PG16
1”- 20 UNEF
VBN-PG21BL18TXX
18
34
70
PG21
1”- 20 UNEF
VBN-PG16BL20TXX
20
33
70
PG16
1 1/8”-18 UNEF
VBN-PG29BL20TXX
20
43
75
PG29
1 1/8”-18 UNEF
VBN-PG16BL22TXX
22
36
70
PG16
1 1/4”-18 UNEF
VBN-PG29BL22TXX
22
36
70
PG29
1 1/4”-18 UNEF
VBN-PG21BL24TXX
24
40
75
PG21
1 3/8”-18 UNEF
VBN-PG29BL24TXX
24
43
75
PG29
1 3/8”-18 UNEF
VBN-PG36BL24TXX
24
54
85
PG36
1 3/8”-18 UNEF
VBN-PG21BL28TXX
28
46
75
PG21
1 5/8”-18 UNEF
VBN-PG29BL28TXX
28
46
75
PG29
1 5/8”-18 UNEF
VBN-PG29BL32TXX
32
51.5
85
PG29
1 7/8”-16 UN
VBN-PG36BL32TXX
32
54
85
PG36
1 7/8”-16 UN
VBN-PG36BL36TXX
36
58
95
PG36
2 1/16”-16 UN
VBN-PG42BL36TXX
36
58
95
PG42
2 1/16”-16 UN
VBN-PG36BL40TXX
40
64.5
95
PG36
2 5/16”-16 UN
VBN-PG42BL40TXX
40
64.5
95
PG42
2 5/16”-16 UN
For additional thread size please consult the factory. Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
46
www.ittcannon.com
VBN SPARE BACKSHELLS
VBN-90R-Standard 90° backshell with UNEF external thread.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
A
E
B
THREAD F
C
THREAD V
D
Part Number
Shell size
A
B
ØC Max.
VBN-90R16STXX
16S
40
30
30
VBN-90R18TXX
18
47
35
35
ØD Max.
E Min.
Thread F
Thread V
14.7
10
7/8”-20 UNEF
7/8”-20 UNEF
17.2
10
1”-20 UNEF
1”-20 UNEF
VBN-90R20TXX
20
53
35
37.3
20.35
10
1 1/8”-18 UNEF
1 3/16”-18 UNEF
VBN-90R22TXX
22
53
35
42
23
10
1 1/4”-18 UNEF
1 3/16”-18 UNEF
VBN-90R24TXX
24
52
40
46
25.8
10
1 3/8”-18 UNEF
1 7/16”-18 UNEF
VBN-90R28TXX
28
52
40
51
28.7
10
1 5/8”-18 UNEF
1 7/16”-18 UNEF
VBN-90R32TXX
32
56
45
58
36.5
12
1 7/8”-18 UN
1 3/4”-18 UNS
VBN-90R36TXX
36
59
50
62
42.6
12
2 1/16”-16 UN
2 ”-18 UNS
VBN-90R40TXX
40
65
55
69
48.6
12
2 5/16”-16 UN
2 1/4”-16 UN
The backshell is supplied with an adapter to be connected to the mating parts of the connector. Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
47
VBN SPARE BACKSHELLS
VBN-MXXA-Adapter with metric internal thread.
Can be used on the 90° backshell.
Supplied with O-Ring
L
THREAD F
THREAD B
A
Part Number
Shell Size
ØA Max.
L
VBN-M12A16STXX
VBN-M16A16STXX
16S
26
27
M16x1.5
M16x1.5
18
34
30
36.5
27
M20x1.5
36.5
27
M25x1.5
43
30
M32x1.5
VBN-M25A18TXX
M20x1.5
20/22
VBN-M32A20TXX
VBN-M25A24TXX
43
27
M25x1.5
43
27
M32x1.5
VBN-M40A24TXX
54
38
M40x1.5
VBN-M25A32TXX
50
27
M25x1.5
50
27
M32x1.5
54
38
M40x1.5
57.2
27
M40x1.5
65
27
M40x1.5
65
27
M50x1.5
69
31
M63x1.5
VBN-M32A32TXX
24/28
32
VBN-M40A32TXX
VBN-M32A36TXX
VBN-M40A36TXX
1 7/16”-18 UNEF
1 3/4”-18UNS
2” -18UNS
M50x1.5
VBN-M40A40TXX
VBN-M63A40TXX
1 3/16”-18 UNEF
M32x1.5
36
VBN-M50A36TXX
VBN-M50A40TXX
1”-20 UNEF
M25x1.5
VBN-M20A20TXX
VBN-M32A24TXX
7/8”-20 UNEF
M20x1.5
VBN-M16A18TXX
VBN-M25A20TXX
Thread F
M12x1.5
VBN-M20A16STXX
VBN-M20A18TXX
Thread B
40
2 1/4”-16UN
For additional thread size please consult the factory. Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
48
www.ittcannon.com
VBN SPARE BACKSHELLS
VBN-PGXXA-Adapter with PG internal thread.
Can be used on the 90° backshell.
A
THREAD B
THREAD F
L
Part Number
Shell Size
ØA Max.
VBN-PG9A16STXX
16S
26
31
34
34
PG21
36.5
27
PG16
43
27
PG29
43
27
PG21
43
27
PG29
VBN-PG16A18TXX
VBN-PG21A18TXX
VBN-PG16A20TXX
VBN-PG29A20TXX
18
20/22
VBN-PG21A24TXX
VBN-PG29A24TXX
24/28
L
Thread B
Thread F
27
PG9
7/8”-20 UNEF
28.3
PG16
VBN-PG36A24TXX
54
38
PG36
VBN-PG29A32TXX
50
25.3
PG29
54
36.3
PG36
57.2
27
65
31
PG42
65
31
PG48
VBN-PG36A32TXX
VBN-PG36A36TXX
VBN-PG42A36TXX
VBN-PG42A40TXX
VBN-PG48A40TXX
32
36
40
For additional thread size please consult the factory. Add plating suffix to the part number
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
49
PG36
PG42
1”-20 UNEF
1 3/16”-18 UNEF
1 7/16”-18 UNEF
1 3/4”-18UNS
2” -18UNS
2 1/4”-16UN
VBN SPARE BACKSHELLS
MGVBN-M—
VBN-CS1F—
Special straight backshell rubber covered and
internal metric thread
These backshell offers the possibility to fix the wires
bundle using tie band; it also foresees a knurled area
where shielding braid or heat-shrink tube can be
fixed.
It offers improved mechanical protection and
electrical insulation.
Three threaded holes allows connection of ground
wires.
Can be used on both plug and receptacle
connectors, with or without grommet.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
Supplied with O-Ring
A
L
A
Ordering Part
Number
ØA
±0.5
L ±1
Thread F
THREAD C
THREAD F
THREAD C
THREAD F
L
Thread C
Ordering Part
Number
ØA
max.
ØB
±0.2
L1
±0.3
Thread F
W slots
VBN-CS1F18TXXX
35
16.4
44.5
1” – 20UNEF
16x4 (#5)
M32 x 1.5
VBN-CS1F20TXXX
37
19.3
44.5
MGVBN-M20BL18
33
65
1” – 20UNEF
M20 x 1.5
MGVBN-M25BL20
42
65
1” 1/8 – 20UNEF
M25 x 1.5
MGVBN-M25BL22
43
65
1” ¼ - 18UNEF
M25 x 1.5
MGVBN-M32BL24
46
65
1” 3/8 – 18UNEF
MGVBN-M32BL28
53
75
1” 5/8 – 18UNEF
M32 x 1.5
VBN-CS1F22TXXX
42
22.0
44.5
MGVBN-M32BL32
56
78
1” 7/8 – 16UN
M32 x 1.5
VBN-CS1F28TXXX
51
29.0
42
MGVBN-M40BL40
72
90
2” 5/16 – 16UN
M40 x 1.5
VBN-CS1F32TXXX
56
34.8
43
1” 1/8 – 20UNEF 16x4 (#5)
1” ¼ - 18UNEF
16x4 (#6)
1” 5/8 – 18UNEF 16x4 (#7)
1” 7/8 – 16UN
16x4 (#7)
Dimensions shown in mm
Specifications and dimensions subject to change
50
www.ittcannon.com
VBN SPARE BACKSHELLS
VBN-CS28T108
These special backshell foresees a tilting cage for the
fixing of the wires bundle using tie band; the cage can
be positioned in a straight way or with an angle of 30°.
Two threaded holes allows connection of ground wires.
Can be used on both plug and receptacle connectors,
with or without grommet.
Supplied with O-Ring
53
Support cage in
straight position
Support cage in
tilted position
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
35
30°
1.6250-18UNEF
51
43
51
Example of wiring
assembly
VBN ACCESSORIES
VBNZ-Individual wire seal grommet.
Supplied with plastic compression ring.
The grommet foreseen stepped holes with membrane.
Shell Size
Insert layout
Male part number
Female part number
Wire O.D.
16S
16S-1
VBNZ16S-1P
VBNZ16S-1S
1.0/3.0
18
18-19
VBNZ18-19P
VBNZ18-19S
1.0/3.0
20
20-4
VBNZ20-4P
VBNZ20-4S
2.5/4.5
20
20-7
VBNZ20-7P
VBNZ20-7S
1.0/3.2
20
20-15
VBNZ20-15P
VBNZ20-15S
2.5/4.5
22
22-14
VBNZ22-14P
VBNZ22-14S
1.0/3.0
22
22-23
VBNZ22-23P
VBNZ22-23S
2.5/4.5
24
24-10
VBNZ24-10P
VBNZ24-10S
4.0/6.0
28
28-21
VBNZ28-21P
VBNZ28-21S
0.8/1.8
28
28-21
VBNZ28-21PH
VBNZ28-21SH
1.8/3
32
32A-13
VBNZ32A-13P
VBNZ32A-13S
2.5/4,5
36
36-10
VBNZ36-10P
VBNZ36-10S
0.8/1,8
36
36-10
VBNZ36-10PH
VBNZ36-10SH
1.8/3
36
36A-22
VBNZ36A-22P
VBNZ36A-22S
2.5/4.5
40
40A-35
VBNZ40A-35P
VBNZ40A-35S
2.5/4.5
40
40A-60
VBNZ40A-60P
VBNZ40A-60S
0.8/1.8
40
40A-60
VBNZ40A-60PH
VBNZ40A-60SH
1.8/3
40
40A-70
VBNZ40A-70P
VBNZ40A-70S
1.0/2.0
40
40A-70
VBNZ40A-70PH
VBNZ40A-70SH
2.0/3.0
Dimensions shown in mm
Specifications and dimensions subject to change
52
www.ittcannon.com
VBN ACCESSORIES
INSERT HOLE PLUG
Rubber hole plug; used to close unused cavity of
the insulator and prevent dust and dirty entry.
Available for all the contact size
A
B
Contact size
P/N
ØA
B
16 / 16S
51605-16
3.7
13.5
12
51605-12
5.4
15.5
8
51605-8
7.5
19.7
GROMMET HOLE PLUG
Plastic hole plug used in case the membrane of the
grommet holes is pierced incorrectly or damaged.
L1
D2
D1
L1
L2
Contact size
P/N
D1
D2
L1
L2
Color
16 / 16S
VG95234 B16
2.8
3.7
3.2
11.9
Blue
12
VG95234 B12
3.7
4.6
3.2
11.9
Yellow
8
VG95234 B8
5
5.8
3.2
11.9
White
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
53
VBN ACCESSORIES
VBN-PDMC- POLARIZATION PIN
The “plastic dummy contacts” are longer than standard
male contacts and can be installed in one or more
contact cavities instead of standard male contacts, to
completely remove the possibility of cross mating.
Cannot be used on 16S-1 arrangement.
A
B
Part Number
Size
ØA
B
VBN-PDMC-16
16
2.8
35
VBN-PDMC-12
12
4.0
35
ALIGNMENT PIN VBN-PAP-16
For big size and high density, symmetrical contact
arrangements, where very few contacts are being
used, additional plastic alignment pin can guarantee a
better mating of the contacts.
It is suggested to use two or more of them.
They can be installed from the front of the male insulator.
Available only for size 16 cavities.
27
3.85
Dimensions shown in mm
Specifications and dimensions subject to change
54
www.ittcannon.com
VBN ACCESSORIES
VE3057--AB
General duty cable clamp with bushing suitable for
jacketed or multi-conductor cable or wire bundles
protected by shrink tubing.
L
B
A
C
D
THREAD V
Part Number
Used with
conn. size
A
B
C
ØD
L
Thread V
VE3057-8ABTXX
16-16S
10.5
24
28
11.1
72.2
7/8”-20 UNEF
VE3057-10ABTXX
18
10.5
28.5
33
14.3
69
1”-20 UNEF
VE3057-12ABTXX
20-22
10.5
24
35
15.9
66
1 3/16”-18 UNEF
VE3057-16ABTXX
24-28
10.5
26
43
19.1
63
1 7/16”-18 UNEF
VE3057-20ABTXX
32
12.5
28
51
23.8
62
1 3/4”-18 UNS
VE3057-24ABTXX
36
14
29.4
58
31.8
60
2”-18 UNS
VE3057-28ABTXX
40
14
42.8
65
35
57
2 1/4”-16 UN
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
55
VBN ACCESSORIES
FRVE3057--C
Waterproof cable clamp providing concentric
clamping over the cable jacket.
G
B
E
F
THREAD A
THREAD V
Part Number
Used
With size
Thread A
B
Open
E ±0.4
F ±0.2
G +0.5-0
Thread V
Closed
FRVE3057-8CTXX
16-16S
7/8”-20 UNEF
13.48
8
25.4
28.1
32.3
6-32 UNC
FRVE3057-10CTXX
18
1”-20 UNEF
15.87
9.6
28.5
31
35.3
6-32 UNC
FRVE3057-12CTXX
20-22
1 3/16”-18 UNEF
19
11.3
33.3
37.3
35.7
8-32 UNC
FRVE3057-18CTXX
24-28
1 7/16”-18 UNEF
23.8
15.5
39.6
42
38.5
8-32 UNC
FRVE3057-20CTXX
32
1 3/4”-18 UNS
31.75
23.4
47.6
54
44.8
.250-20 UNC
FRVE3057-24CTXX
36
2”-18 UNS
35
23.4
53.9
57.1
51.6
.250-20 UNC
FRVE3057-28CTXX
40
2 1/4”-16 UN
41.25
29.9
60.3
63.5
51.6
.250-20 UNC
Dimensions shown in mm
Specifications and dimensions subject to change
56
www.ittcannon.com
VBN ACCESSORIES
SQUARE PANEL GASKET
FOR FRONT MOUNTING RECEPTACLE
Used on front panel mounting receptacle (type VBN2)
Not conductive square gasket (“N” type”).
Chloroprene rubber.
Protection degree: IP67
Conductive square gasket (“NS” type”).
Silicone rubber with conductive filler
Protection degree: IP65
C
A
C
A
B
D
Size
A ±0.2
B +1 -0
C ±0.5
D +0.5 -0
“N” type (non-conductive)
according to VG spec
“NS” type (conductive) according to VG spec
16-16S
24
25.3
32.5
4.2
VG95234 DA-16-1
VG95234 DA-16-2
18
27
28.4
35
4.2
VG95234 DA-18-1
VG95234 DA-18-2
20
29.4
31.6
38
4.2
VG95234 DA-20-1
VG95234 DA-20-2
22
31.8
34.8
41
4.2
VG95234 DA-22-1
VG95234 DA-22-2
24
34.9
38
44.5
4.2
VG95234 DA-24-1
VG95234 DA-24-2
28
39.7
44.3
50.8
5.1
VG95234 DA-28-1
VG95234 DA-28-2
32
44.5
50.7
57
5.1
VG95234 DA-32-1
VG95234 DA-32-2
36
49.2
57
63.5
5.1
VG95234 DA-36-1
VG95234 DA-36-2
40
55.5
61.9
70
5.6
16968
16968/1
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
57
VBN ACCESSORIES
SQUARE PANEL GASKET
FOR REAR MOUNTING RECEPTACLE
Used on rear panel mounting receptacle (type VBN3)
Not conductive square gasket (“N” type”).
Chloroprene rubber.
Protection degree: IP67
Conductive square gasket (“NS” type”).
Silicone rubber with conductive filler
Protection degree: IP65
C
A
C
A
B
D
Size
A ±0.2
16-16S
18
D +0.5 -0
“N” type (non-conductive)
according to VG spec
“NS” type (conductive)
according to VG spec
B +3 -0
C ±0.5
24.6
27.4
32.5
4.2
VG95234 DH-16-1
VG95234 DH-16-2
27
30.8
35
4.2
VG95234 DH-18-1
VG95234 DH-18-2
20
29.4
34.2
38
4.2
VG95234 DH-20-1
VG95234 DH-20-2
22
31.8
37.4
41
4.2
VG95234 DH-22-1
VG95234 DH-22-2
24
34.9
40.9
44.5
4.2
VG95234 DH-24-1
VG95234 DH-24-2
28
39.7
46.7
50.8
5.1
VG95234 DH-28-1
VG95234 DH-28-2
32
44.5
53.4
57
5.1
VG95234 DH-32-1
VG95234 DH-32-2
36
49.2
59.6
63.5
5.1
VG95234 DH-36-1
VG95234 DH-36-2
40
55.5
65.5
69.9
5.1
46739-40
46739-40-1
Dimensions shown in mm
Specifications and dimensions subject to change
58
www.ittcannon.com
VBN ACCESSORIES
FRCIR--TF
Metal dust cap with stainless steel chain and
Flame Retardant gasket
Used on receptacle.
Used on
conn. size
D1
Max.
D2
+0.5-0
L1
±0.2
L2
Approx.
FRCIR16STFTxx
16S
33
4.4
16
127
FRCIR18TFTxx
18
37.5
4.4
20.7
127
FRCIR20TFTxx
20
41
4.4
20.7
127
FRCIR22TFTxx
22
44
4.4
20.7
127
FRCIR24TFTxx
24
47.5
4.4
20.7
127
FRCIR28TFTxx
28
54.5
5.6
20.7
190
FRCIR32TFTxx
32
61
5.6
20.7
190
FRCIR36TFTxx
36
67.5
5.6
20.7
175
FRCIR40TFTxx
40
73
5.6
20.7
190
L2
Part Number
d1
L1
d2
CIR—TV
Metal dust cap with stainless steel chain.
Used on plug.
Used on
conn. size
D1
Max.
D2
+0.5-0
L1
±0.2
L2
Approx.
CIR16STVTxx
CIR18TVTxx
16S
30
4.4
23.5
127
18
33.5
4.4
31.5
127
CIR20TVTxx
20
37
4.8
31.5
140
CIR22TVTxx
22
40
4.8
31.5
140
CIR24TVTxx
24
43.5
4.8
31.5
140
CIR28TVTxx
28
49.5
4.8
31.5
190
CIR32TVTxx
32
56
5.6
31.5
190
CIR36TVTxx
36
62.5
5.6
31.5
190
CIR40TVTxx
40
67.7
5.6
31.5
190
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
59
L2
Part Number
d1
L1
d2
VBN APPLICATION NOTES
C
PANEL CUT-OUT
D
E
VBN3 Rear mounting panel cut-out dimensions
VBN2 Front mounting panel cut-out dimensions
Shell Size
C ±0.1
D
ØE +0.1 -0
Shell Size
C ±0.1
D
ØE +0.1 -0
16S
24.6
28.3
4.5
16S
18
27
31.7
4.5
18
24.6
23
3.4
27
26.5
3.4
20
29.4
35
4.5
20
29.4
30
3.4
22
31.8
38.3
24
34.9
41.8
4.5
22
31.8
33
3.4
4.5
24
34.9
36
3.9
28
39.7
32
44.5
47.6
5.5
28
39.7
42
3.9
54.3
5.5
32
44.5
48.5
4.5
36
40
49.2
60.5
5.5
36
49.2
55
4.5
55.5
66.4
5.5
40
55.5
61
4.5
PANEL THICKNESS FOR REAR MOUNTING RECEPTACLE
STANDARD PLUG CONNECTOR
TYPE VBN--
S Max.
Connector size
VBN6
16S
7.2
MGPVBN6
18
7.5
6.3
20
7.5
6.3
22
7.5
6.3
24
7.5
6.3
28
8.2
7
32
7.5
6.3
36
7.5
6.3
40
7.5
6.3
S
REAR MOUNTING RECEPTACLE
TYPE VBN3--
RUBBER COVERED PLUG CONNECTOR
TYPE MGPVBN6-SHORT COUPLING NUT
The panel dimension doesn’t include the bolt head.
Dimensions shown in mm
Specifications and dimensions subject to change
60
www.ittcannon.com
VBN APPLICATION NOTES
BACKSHELL TORQUE VALUES
Shell Size
Max. Backshell to Connector Tightening Torque (Nm)
16S
7.4
18
7.8
20
9.8
22
11.8
24
14.7
28
18.6
32
20.6
36
26.5
40
39.2
The above values are based upon the most densely populated contact arrangements with cables at
the maximum limit for the grommet. The values are for guidance only.
FIXING SCREW TORQUE VALUES
Thread
Max. torque for screw at the flanges (Nm)
M3
1.2 ±0.2
M4
1.4 ±0.2
M5
2.0 ±0.2
The above values are based upon the most densely populated contact arrangements with cables at
the maximum limit for the grommet. The values are for guidance only.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
61
VBN APPLICATION NOTES
Setting for authorized crimp tools
PIN CONTACTS
Male Part
number
Contact size
Cable
DIN mm2
Crimping tool
(see note)
Crimping die
16S
VM8 or CT8N(M)
VH435
16S
51513-16-12
16
VM8 or CT8N(M)
VH435
2.5/3
12
VM8 or CT8N(M)
VH435
VM8 or CT8N(M)
VH435
0.5
16
51513-12
12
51513-12-12
12
Green
ET16VBN
7
8
Green
ET16VBN
4
Blue
ET16VBN
Blue
ET16VBN
Blue
ET16VBN
Red
ET12VBN
Red
ET12VBN
Red
ET12VBN
5
1.5
VM8 or CT8N(M)
VH435
VM8 or CT8N(M)
VH435
CT8N (M)
VH435
CT8N (M)
VH435
14
51513-16-26
6
3
1
16
ET16VBN
3
0.75
20
51513-16-20
Green
5
1.5
14
51513-16S-26
4
3
1
16S
Removal tool
3
0.75
20
51513-16S-20
Tool position
AWG
0.5
51513-16S-12
Selector
number
2.5/3
12
2.5/3
12
0.5
6
7
8
7
3
0.75
20
4
3
1
7
1.5
51513-12-20
12
2
14
CT8N (M)
VH435
16
8
7
18
51513-12-30
12
4
CT8N (M)
VH435
8
Red
ET12VBN
51513-12-38
12
6
CT8N (M)
VH435
8
Red
ET12VBN
MP-F80-VGE (H)
44519-8T70
51513-8
8
8
HT45 (M)
B50 (E)
51513-8-20
8
1.0/2.0
3
12
51513-8-26
8
3
12
3
12
MP-F80-VGE (H)
44519-8-1T70
MP-F80-VGE (H)
44519-425T70
HT45 (M)
8
4
HT45 (M)
MP-F80-VGE (H)
8
6
HT45 (M)
B50 (E)
MP-F80-VGE (H)
51513-8-50
8
10
ET8VBN
ET8VBN
B50 (E)
B50 (E)
51513-8-38
ET8VBN
51589-32T70
MP-F80-VGE (H)
51513-8-30
51589-52T70
HT45 (M)
B50 (E)
44519-44T70
51589-37T70
ET8VBN
44519-126T70
51589-37T70
ET8VBN
44519-8T70
51589-52T70
ET8VBN
Note: Manual= (M) Hydraulic= (H) Electrical= (E)
Dimensions shown in mm
Specifications and dimensions subject to change
62
www.ittcannon.com
VBN APPLICATION NOTES
Setting for authorized crimp tools
SOCKET CONTACTS
Female Part
number
Contact size
Cable
DIN mm2
Crimping tool
(see note)
Crimping die
16S
VM8 or CT8N(M)
VH435
16S
51511-16-12
16
VM8 or CT8N(M)
VH435
2.5/3
12
VM8 or CT8N(M)
VH435
VM8 or CT8N(M)
VH435
0.5
16
51511-12
12
51511-12-12
12
Green
ET16VBN
7
8
Green
ET16VBN
4
Red
ET16VBN
Red
ET16VBN
Red
ET16VBN
Red
ET12VBN
Red
ET12VBN
Red
ET12VBN
5
1.5
VM8 or CT8N(M)
VH435
VM8 or CT8N(M)
VH435
CT8N (M)
VH435
CT8N (M)
VH435
14
51511-16-26
6
3
1
16
ET16VBN
3
0.75
20
51511-16-20
Green
5
1.5
14
51511-16S-26
4
3
1
16S
Removal tool
3
0.75
20
51511-16S-20
Tool position
AWG
0.5
51511-16S-12
Selector
number
2.5/3
12
2.5/3
12
0.5
6
7
8
7
3
0.75
20
4
3
1
7
1.5
51511-12-20
12
2
14
CT8N (M)
VH435
16
8
7
18
51511-12-30
12
4
CT8N (M)
VH435
8
Red
ET12VBN
51511-12-38
12
6
CT8N (M)
VH435
8
Red
ET12VBN
MP-F80-VGE (H)
44519-8T70
51511-8
8
8
HT45 (M)
B50 (E)
51511-8-20
8
1.0/2.0
3
12
51511-8-26
8
3
12
3
12
MP-F80-VGE (H)
44519-8-1T70
MP-F80-VGE (H)
44519-425T70
HT45 (M)
8
4
HT45 (M)
MP-F80-VGE (H)
8
6
HT45 (M)
B50 (E)
MP-F80-VGE (H)
51511 -8-50
8
10
HT45 (M)
B50 (E)
Note: Manual= (M) Hydraulic= (H) Electrical= (E)
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
ET8VBN
ET8VBN
B50 (E)
B50 (E)
51511-8-38
ET8VBN
51589-32T70
MP-F80-VGE (H)
51511-8-30
51589-52T70
63
44519-44T70
51589-37T70
ET8VBN
44519-126T70
51589-37T70
ET8VBN
44519-8T70
51589-52T70
ET8VBN
VBN APPLICATION NOTES
Setting for approved crimp tools
PIN CONTACTS
Male Part
number
Contact size
Cable
DIN mm2
Crimping tool
Crimping die
16S
FT8
TH685
Tool position
Removal tool
Blue
ET16VBN
Blue
ET16VBN
Blue
ET16VBN
NF F mm2
0.5
51513-16S-12
Selector
number
6
0.60
0.75
0.93
7
6
1
51513-16S-20
16S
1.34
FT8
TH685
7
1.5
1.82
51513-16S-26
16S
51513-16-12
16
2.5
2.61
8
FT8
TH685
FT8
TP1517
0.5
8
6
0.60
0.75
0.93
7
ET16VBN
6
1
51513-16-20
16
1.34
FT8
TP1517
7
ET16VBN
1.5
1.82
51513-16-26
16
51513-12
12
51513-12-12
12
2.5
2.61
2.5
2.61
8
FT8
TP1517
8
ET16VBN
FT8
TP1519
8
ET12VBN
FT8
TP1519
7
ET12VBN
FT8
TP1519
8
ET12VBN
0.5
0.60
0.75
0.93
1
51513-12-20
12
1.34
1.5
1.82
51513-12-30
12
4
FT8
TP1519
8
ET12VBN
51513-12-38
12
6
FT8
TP1519
8
ET12VBN
M317
TP1520
4
ET8VBN
M317
TP1520
4
ET8VBN
0.93
1.0
51513-8-20
8
1.34
1.5
1.82
2.5
51513-8-26
8
51513-8-30
8
4.0
M317
TP1520
5
ET8VBN
51513-8-38
8
6.0
M317
TP1520
5
ET8VBN
2.61
Dimensions shown in mm
Specifications and dimensions subject to change
64
www.ittcannon.com
VBN APPLICATION NOTES
Setting for approved crimp tools
PIN CONTACTS
Female Part
number
Contact size
Cable
DIN mm2
Crimping tool
Crimping die
16S
FT8
TH685
Tool position
Removal tool
Red
ET16VBN
Red
ET16VBN
Red
ET16VBN
NF F mm2
0.5
51511-16S-12
Selector
number
6
0.60
0.75
0.93
7
6
1
51511-16S-20
16S
1.34
FT8
TH685
7
1.5
1.82
51511-16S-26
16S
51511-16-12
16
2.5
2.61
8
FT8
TH685
FT8
TP1517
0.5
8
6
0.60
0.75
0.93
7
ET16VBN
6
1
51511-16-20
16
1.34
FT8
TP1517
7
ET16VBN
1.5
1.82
51511-16-26
16
51511-12
12
51511-12-12
12
2.5
2.61
2.5
2.61
8
FT8
TP1517
8
ET16VBN
FT8
TP1519
8
ET12VBN
FT8
TP1519
7
ET12VBN
FT8
TP1519
8
ET12VBN
0.5
0.60
0.75
0.93
1
51511-12-20
12
1.34
1.5
1.82
51511-12-30
12
4
FT8
TP1519
8
ET12VBN
51511-12-38
12
6
FT8
TP1519
8
ET12VBN
M317
TP1520
4
ET8VBN
M317
TP1520
4
ET8VBN
0.93
1.0
51511-8-20
8
1.34
1.5
1.82
2.5
51511-8-26
8
51511-8-30
8
4.0
M317
TP1520
5
ET8VBN
51511-8-38
8
6.0
M317
TP1520
5
ET8VBN
2.61
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
65
ADDITIONAL VEAM SOLUTIONS FOR RAIL
INFRASTRUCTURE AND ROLLING STOCK APPLICATIONS
CIR/FRCIR Series
DSR Series
• Available with 1-159 poles, 256 layouts,
2,000 matching cycles
• Flame retardant (EN45545 HL3 - NFPA 130)
• Aluminium shells up to 500h salt spray
resistance
• Stainless steel & marine bronze available
• Double start ratchet threaded
coupling mechanism with 5 Keyways
• Flame retardant (EN45545
HL3 - NFPA130)
• High shock resistance
CIR M12 Series
Power Plate Series
• 1 way and 4 way versions, 3 types of
contacts: 2, 4 & 8-pole
• Performance up to Category 7, supports
communication speed up to 10Gbps
• Flame retardant (EN45545 HL3 - NFPA 130)
• 2-3-4 pole versions, highly
customizable according cable,
current and voltage requirements
• Operating voltage according to
EN50124-1
• Fast and easy coupling system with
two screws or with latch mechanism
CIR290 Series
VRPC Series
• Available with 3 to 101 poles, from 7.5 to
350 A, 2,000 mating cycles
• Flame retardant (EN45545 HL3 - NFPA 130)
• Aluminium shells up to 500h salt spray
resistance
• Available with 3,6,12 way layouts,
machined or stamped contacts
• Smoke & fire resistance per
NFF16-101 & NFF16-102
• IP20 or IP67
• Rear removable cable support
or Rear backshells
HTB Series
CIR Fiber Optic Series
• High Temperature Bayonet connector,
tested at 800ºC for 30 minutes
• Exceeds the standard ISO 834-1
• Creates a REI 0 fire barrier
according EN13501-2 / EN 1363-1
• Available with 4 to 22 multimode
or singlemode fibers
• Supports communictaion speed
up to beyond 10 Gbps
• Customized harnessing service
on request
Dimensions shown in mm
Specifications and dimensions subject to change
66
www.ittcannon.com
VBN PRODUCT SAFETY INFORMATION
THIS NOTE MUST BE READ IN CONJUNCTION WITH THE PRODUCT DATA SHEET/CATALOG. FAILURE
TO OBSERVE THE ADVICE IN THIS INFORMATION SHEET AND THE OPERATING CONDITIONS
SPECIFIED IN THE PRODUCT DATA SHEET/ CATALOG COULD RESULT IN HAZARDOUS SITUATIONS.
or any other undesired conducting particles. Circuit resistance and
continuity check should be made to make certain that there are no high
resistance joints or spurious conducting paths.
Always use the correct application tools as specified in the Data Sheet/
Catalog. Do not permit untrained personnel to wire, assemble or tamper
with connectors. For operation voltage please see appropriate
national regulations.
1. MATERIAL CONTENT AND PHYSICAL FORM
Electrical connectors do not usually contain hazardous materials. They
contain conducting and non-conducting materials and can be divided into
two groups.
a) Printed circuit types and low cost audio types which employ all plastic
insulators and casings.
b) Rugged, Fire Barrier and High Reliability types with metal casings and
either natural rubber, synthetic rubber, plastic or glass insulating materials.
Contact materials vary with type of connector and also application and are
usually manufactured from either: Copper, copper alloys, nickel, alumel,
chromel or steel. In special applications, other alloys may be specified.
IMPORTANT GENERAL INFORMATION
2. FIRE CHARACTERISTICS AND ELECTRIC SHOCK HAZARD
There is no fire hazard when the connector is correctly wired and used
within the specified parameters. Incorrect wiring or assembly of the
connector or careless use of metal tools or conductive fluids, or transit
damage to any of the component parts may cause electric shock or burns.
Live circuits must not be broken by separating mated connectors as this
may cause arcing, ionization and burning. Heat dissipation is greater at
maximum resistance in a circuit. Hot spots may occur when resistance is
raised locally by damage, e.g. cracked or deformed contacts, broken
strands of wire. Local overheating may also result from the use of the
incorrect application tools or from poor quality soldering or slack screw
terminals. Overheating may occur if the ratings in the product Data Sheet/
Catalog are exceeded and can cause breakdown of insulation and hence
electric shock. If heating is allowed to continue it intensifies by further
increasing the local resistance through loss of temper of spring contacts,
formation of oxide film on contacts and wires and leakage currents
through carbonization of insulation and tracking paths. Fire can then result
in the presence of combustible materials and this may release noxious
fumes. Overheating may not be visually apparent. Burns may result from
touching overheated components.
3. HANDLING
Care must be taken to avoid damage to any component parts of electrical
connectors during installation and use. Although there are normally no
sharp edges, care must be taken when handling certain components to
avoid injury to fingers. Electrical connectors may be damaged in transit to
the customers, and damage may result in creation of hazards. Products
should therefore be examined prior to installation/ use and rejected if
found to be damaged.
4. DISPOSAL
Incineration of certain materials may release noxious or even toxic fumes.
5. APPLICATION
Connectors with exposed contacts should not be selected for use on the
current supply side of an electrical circuit, because an electric shock could
result from touching exposed contacts on an unmated connector. Voltages
in excess of 30 V ac or 42.5 V dc are potentially hazardous and care should
be taken to ensure that such voltages cannot be transmitted in any way to
exposed metal parts of the connector body. The connector and wiring
should be checked, before making live, to have no damage to metal parts
or insulators, no solder blobs, loose strands, conducting lubricants, swarf,
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
67
(i) Air and creepage paths/Operating voltage.
The admissible operating voltages depend on the individual applications
and the valid national and other applicable safety regulations. For this
reason the air and creepage path data are only reference values. Observe
reduction of air and creepage paths due to PC board and/or harnessing.
(ii) Temperature
All information given are temperature limits. The operation temperature
depends on the individual application.
(iii) Other important information
Cannon continuously endeavors to improve their products. Therefore,
Cannon products may deviate from the description, technical data and
shape as shown in this catalog and data sheets.
Connect with your ITT Interconnect Solutions representative
today or visit us at www.ittcannnon.com
Connect with the experts
ITT Interconnect Solutions’ Cannon brand is a world leader in
the design and manufacture of highly engineered connector
solutions for multiple end markets.
North America
56 Technology Drive
Irvine, CA 92618
Phone 1.800.854.3208
100 New Wood Road
Watertown, CT 06795
Phone: +1.860.274.9681
Europe
Italy
Corso Europa 41/43
I - 20020 Lainate (MI) Italy
Phone: +39.02938721
Germany
Cannonstrasse 1
D – 71384 Weinstadt, Germany
Phone: +49.7151.699.0
The “ITT Engineered Blocks“ symbol, “Engineered for life”, “ITT”, ”Veam” and “Cannon“ are registered trademarks of ITT Corporation.
Specification and other data are based on information available at the time of printing, and are subject to change without notice.
Asia
Tuopandun Industrial Area, Jinda Cheng,
Xiner Village, Shajing Town, Boan District,
Shenzhen City, Guangdong Province, China 518215
Phone: +86.755.2726.7888
© 2016 ITT Corporation.
ITT Veam VBN Cat 201602