X

Honeywell Performance Series Rugged IP Cameras
Guide Specifications in CSI Format
www.honeywellvideo.com
Rev A – 800-09599
SECTION 282329
PERFORMANCE SERIES RUGGED DAY/NIGHT IP CAMERA
PART 1 GENERAL
1.1
1.2
SECTION INCLUDES
A.
Provide a series of Rugged Day/Night, H.264, fixed mini-dome IP cameras.
B.
Basis of design is the Honeywell Performance Series Rugged Day/Night, H.264, color IP
camera with two resolutions: VGA or 720p. Each camera shall have low light sensitivity of
0.25 lux, H.264 (primary stream) and MJPEG (secondary steam) compression, PSIA
compliance, and a choice of PoE IEEE 802.3af Class 1 or 24 V AC power input.
RELATED SECTIONS
NOTE TO SPECIFIER: Include related sections as appropriate if camera system is integrated to other
systems.
A.
Section 260500 – Common Work Results for Electrical, for interface and coordination with
building electrical systems and distribution.
B.
Section 280513 – Conductors and Cables for Electronic Safety and Security, for cabling
between system servers, panels and remote devices.
C.
Section 280528 – Pathways for Electronic Safety and Security, for conduit and raceway
requirements.
282329-1
Honeywell Performance Series Rugged IP Cameras
www.honeywellvideo.com
1.3
Section 282323 – Video Surveillance Systems Infrastructure for interface to and
administration of video recording devices.
E.
Section 282329 – Video Surveillance Remote Devices and Sensors for interface to and use
of video surveillance devices and sensors.
REFERENCES
Reference Standards: Provide systems which meet or exceed the requirements of the
following publications and organizations as applicable to the Work of this Section:
1.
Canadian ICES-003
2.
Canadian Standards Association (CSA)
3.
Conformity for Europe (CE)
4.
Federal Communications Commission (FCC)
5.
Joint Photographic Experts Group (JPEG)
6.
Moving Picture Experts Group (MPEG)
7.
National Television Systems Committee (NTSC)
8.
Phase Alternating by Line (PAL)
9.
Underwriters Laboratories Inc. (UL)
SYSTEM DESCRIPTION
A.
1.5
Rev A – 800-09599
D.
A.
1.4
Guide Specifications in CSI Format
The Performance Series Rugged Day/Night color IP camera shall have VGA or 720p
resolution, H.264 (primary stream) and MJPEG (secondary stream) compression formats,
PSIA compliance and a choice of PoE IEEE 802.3af Class 1 or 24 V AC power input. The
camera shall feature a ¼” progressive scan CMOS imager for clean, sharp images.
SUBMITTALS
282329-2
Honeywell Performance Series Rugged IP Cameras
Guide Specifications in CSI Format
www.honeywellvideo.com
1.6
Rev A – 800-09599
A.
Manufacturer’s Product Data: Submit manufacturer’s data sheets indicating systems and
components proposed for use, including instruction manuals.
B.
Shop Drawings: Submit complete shop drawings including connection diagrams for
interfacing equipment, list of connected equipment, and locations for major equipment
components.
C.
Record Drawings: During construction maintain record drawings indicating location of
equipment and wiring. Submit an electronic version of record drawings not later than
Substantial Completion of the project.
D.
Operation and Maintenance Data: Submit manufacturer’s operation and maintenance
data, customized to the system installed. Include system and operator manuals.
E.
Field Tests: Submit results of field testing of every device including date, testing personnel,
retesting date if applicable, and confirmation that every device passed field testing.
F.
Maintenance Service Agreement: Submit a sample copy of the manufacturer’s
maintenance service agreement, including cost and services for a one year period for
Owner’s review. Maintenance shall include, but not be limited to, labor and materials to
repair the system, provide test and adjustments, and regular inspections.
QUALITY ASSURANCE
A.
Manufacturer: Minimum ten years experience in manufacturing and maintaining video
management systems. Manufacturer shall provide toll-free technical assistance and
support available 24/7.
B.
Manufacturing Location: Provide equipment assembled in China.
C.
Installer: Minimum two years experience installing similar systems, and acceptable to the
manufacturer of the video surveillance system.
282329-3
Honeywell Performance Series Rugged IP Cameras
www.honeywellvideo.com
D.
E.
1.7
Rev A – 800-09599
Environmental Conditions: IP camera shall be designed to function in the following
environmental conditions:
1.
Operating Temperature: -4°F to 122°F (-20°C to 50°C) 0-85% non-condensing.
2.
Emissions: FCC part 15A, CE (EN55022).
3.
Immunity: CE (EN55024).
4.
Safety: EU: 2001/95/EC GPSD, UL 60950-1.
Power Requirements: Components shall have the following electrical specifications: 24 V
AC, or PoE IEEE 802.3af (class 1), 3.5 W power consumption (max), 1.5 kW transient surge
suppression, and 17-28 V AC input range.
DELIVERY, STORAGE, AND HANDLING
A.
1.8
Deliver materials in manufacturer’s labeled packages. Store and handle in accordance with
manufacturer’s requirements, in a facility with environmental conditions within
recommended limits.
WARRANTY
A.
Manufacturer’s Warranty: Submit manufacturer’s standard three-year warranty.
PART 2 PRODUCTS
2.1
Guide Specifications in CSI Format
MANUFACTURER
282329-4
Honeywell Performance Series Rugged IP Cameras
www.honeywellvideo.com
A.
2.2
2.3
Guide Specifications in CSI Format
Rev A – 800-09599
Performance Series IP Camera Manufacturer: Honeywell Performance Series Network
Camera, www.honeywellvideo.com or www.honeywellintegrated.com.
DEVICE COMPONENTS
A.
Network camera captures and transmits video images digitally over a network connection.
B.
IP Utility component discovers and configures network settings for devices, such as
network cameras.
C.
Web-Client component displays network camera live video feeds and provides
configuration of camera settings.
OPERATIONAL REQUIREMENTS
A.
Network camera shall capture and transmit high-quality video images. Captured video shall
have the following major capabilities:
1.
Imager: Progressive scan, ¼” CMOS sensor provides clean, sharp images.
2.
Choice of camera resolution with VGA resolution for camera model HD54IP/X and
720p resolution for camera model HD55IP/X. Effective pixel counts will be no less
than 640 x 480 (VGA) or 1280 x 720 (720p).
3.
3.3 to 12.0 mm Vari-focal Auto Iris Day/Night lens.
4.
Image transmission: The camera shall support dual video streams simultaneously
with multiple compression formats and with frames per second rates up to 30 fps
(NTSC) and 25 fps (PAL).
5.
Dual video streaming: The camera shall have dual video streaming (H.264
compression for the primary stream and MJPEG for the secondary stream). The
frame rate and bandwidth on each stream shall be independently configurable. A
third analog stream will be available for video backup, and for local viewing during
video setup (full resolution not available).
6.
Day/Night performance with 2D edge enhancement, and Digital Noise Reduction
technology.
282329-5
Honeywell Performance Series Rugged IP Cameras
www.honeywellvideo.com
B.
C.
Guide Specifications in CSI Format
Rev A – 800-09599
7.
Low light performance: 0.25 lux @ 50 IRE, F1.6, or 0.11 lux @ 30 IRE, F1.6.
8.
Signal to Noise ratio: The camera shall have a signal to noise ratio of 50 dB with the
AGC (Auto Gain Control) turned off.
9.
Auto white balance: The camera shall incorporate auto white balance to constantly
monitor the light and adjust the color as needed. Automatic white balance ranges
shall be selectable using the web browser interface.
10.
Electronic shutter and AGC: The camera shall include an electronic shutter and
selectable automatic gain control (AGC) for operation in a wide range of lighting
conditions.
Compact housing and dome, and single piece design integrates the camera and lens into
one unit for easy installation. The physical camera options, including housing and dome,
shall have the following major capabilities:
1.
Housing: The camera shall be available in a polycarbonate housing and dome, with a
matte texture and off-white finish.
2.
Installation methods: The camera shall come ready to be surface mounted to a wall
or ceiling. Wall and pendant mount kits are also available for additional installation
options.
3.
3-D axis gimbal (360° pan, 180° tilt, 360° horizontal rotation) for mechanical camera
positioning and adjustment.
4.
Connectors: The cameras shall come standard with an RJ45 Ethernet connector for
network connectivity and PoE (Power over Ethernet), a removable screw block
power connector for a separate 24 V AC power supply, and a 2-pin molex connector
(75 ohms) for local video adjustment and focus.
Network camera shall offer an IP Utility application to discover IP devices in your system
and configure device network settings. The Honeywell IP Utility application shall have the
following major capabilities:
1.
IP address identification for remote device discovery. Supports both dynamic (DHCP)
and static (APIPA) IP address assignment.
2.
Continuous checking of the connected device status for non-stop video recording.
3.
Network configuration of devices for remote control of all camera settings.
4.
Remote firmware upgrade over HTTP.
282329-6
Honeywell Performance Series Rugged IP Cameras
Guide Specifications in CSI Format
www.honeywellvideo.com
D.
E.
2.4
Rev A – 800-09599
Network camera shall offer video access from a web browser and include a web based
graphical user interface (GUI), called the web client, which provides complete control of the
camera settings. The web client shall have the following major capabilities:
1.
Intuitive interface for quick system setup, adjusting of camera and auto iris levels,
and performing remote firmware updates.
2.
Web client access: Supports 1 Administrator and 3 guests. Administrator has full
control of the camera, and 3 guests can view live video from the camera. These four
(4) users can log on at the same time.
3.
Security: Supports two (2) user access levels with password protection. Administrator
has full access and guest user has live view only.
The cameras shall also include the following major capabilities:
1.
Camera tamper detection: The camera shall support camera sabotage or tamper
detection to provide a notification or disruption to the video stream. The three (3)
forms of detection are camera blurring, blinding, and change of scene.
2.
Video motion detection: The camera shall support video motion detection (VMD) to
ensure video integrity and provide a real-time notification of a live motion event.
This feature comes standard with five (5) different, user-selectable motion detection
regions.
3.
Protocol support: HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, RTCP, FTP, ICMP, DHCP,
Bonjour, IGMP, Telnet.
4.
Interoperability: The camera will meet PSIA compliance specifications to guarantee
interoperability between network video products.
DEVICE HARDWARE
A.
Network camera shall have the following mechanical specifications:
1.
Unit Dimensions (W x H): 6.1” x 4.61” (154.97 mm x 117.5 mm)
2.
Unit Weight: 3.0 lb (1.3 kg)
282329-7
Honeywell Performance Series Rugged IP Cameras
Guide Specifications in CSI Format
www.honeywellvideo.com
B.
C.
2.5
Rev A – 800-09599
3.
Auxiliary Video Output: 2-pin molex connector (75 ohms)
4.
Ethernet Connector: RJ45
5.
Power Input: Removable screw block
6.
Housing Construction: Die cast aluminum
7.
Dome Construction: Polycarbonate
8.
Color: Cool gray powder coat
Network camera shall have the following electrical specifications:
1.
Voltage: 24 V AC, Power over Ethernet (PoE) IEEE 802.3af, Class 1
2.
Input Range: 17 – 28 V AC / PoE
3.
Surge Suppression: 1.5 kW transient
4.
Power Consumption: 3.5 W maximum
Network camera shall be designed to meet the following environmental conditions:
1.
Operating Temperature: -4°F to 122°F (-20°C to 50°C)
2.
Storage Temperature: -40°F to 158°F (-40°C to 70°C)
3.
Relative Humidity: 0-85%, non-condensing
4.
Emissions: FCC part 15B, Class A, CE (EN55022).
5.
Immunity: CE (EN55024).
6.
Safety: EU: 2001/95/EC GPSD, UL 60950-1.
MANUFACTURER SUPPORT
A.
Manufacturer shall provide customer service, pre-sales applications assistance, after-sales
technical assistance, access to technical online support, and online training using Web
conferencing.
282329-8
Honeywell Performance Series Rugged IP Cameras
www.honeywellvideo.com
B.
Guide Specifications in CSI Format
Rev A – 800-09599
Manufacturer shall provide 24/7 technical assistance and support via a toll-free telephone
number at no extra charge.
PART 3 EXECUTION
3.1
EXAMINATION
A.
3.2
3.3
Examine site conditions prior to installation. Notify Architect and Owner in writing if
unsuitable conditions are encountered. Do not start installation until site conditions are
acceptable.
INSTALLATION
A.
All components of the camera shall be thoroughly tested before shipping from the
manufacturer’s facility.
B.
The cameras shall be installed, programmed and tested in accordance with manufacturer’s
installation instructions.
1.
Coordinate interfaces with Owner’s representative where appropriate.
2.
Provide mounting supports, conduit, cable, and wire for a complete and reliable
installation. Obtain Owner’s approval for exact location of all cameras, conduit, and
wiring runs prior to installation.
3.
Install conduit, cable, and wire parallel and square with building lines, including
raised floors areas. Do not exceed forty percent fill in conduits. Gather wires and tie
to create an orderly installation.
4.
Coordinate with other trades to provide proper sequencing of installation.
FIELD COMMISSIONING AND CERTIFICATION
282329-9
Honeywell Performance Series Rugged IP Cameras
Guide Specifications in CSI Format
www.honeywellvideo.com
A.
3.4
Rev A – 800-09599
Field Commissioning: Test camera system as recommended by manufacturer, including the
following:
1.
Conduct complete inspection and testing of equipment, including verification of
operation with connected equipment.
2.
Test devices and demonstrate operational features for Owner’s representative and
authorities having jurisdiction as applicable.
3.
Correct deficiencies until satisfactory results are obtained.
4.
Submit written copies of test results.
TRAINING
A.
Conduct on-site system administrator and security/surveillance operator training, with the
number of sessions and length of sessions as recommended by the video surveillance
system manufacturer. Training shall include administration, provisioning, configuration,
operation and diagnostics.
END OF SECTION
282329-10