dm00026748

UM1075
User manual
ST-LINK/V2 in-circuit debugger/programmer
for STM8 and STM32
Introduction
The ST-LINK/V2 is an in-circuit debugger/programmer for the STM8 and STM32
microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire
debugging (SWD) interfaces, facilitate the communication with any STM8 or STM32
microcontroller located on an application board.
In addition to providing the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL
features digital isolation between the PC and the target application board. It also withstands
voltages of up to 1000 VRMS.
The USB full-speed interface allows communication with a PC and:
•
STM8 devices via ST Visual Develop (STVD) or ST Visual Program (STVP) software
(which are available from STMicroelectronics).
•
STM32 devices via Atollic®, IAR™, Keil®, and TASKING integrated development
environments.
Figure 1. ST-LINK/V2 and ST-LINK/V2-ISOL
ST-LINK/V2
March 2016
ST-LINK/V2-ISOL
DocID018748 Rev 7
1/19
www.st.com
1
Contents
UM1075
Contents
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
Product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4
Hardware configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1
5
Connection with STM8 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1.1
Standard ERNI connection with SWIM flat ribbon . . . . . . . . . . . . . . . . . . 9
4.1.2
Low-cost SWIM connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1.3
SWIM signals and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2
Connection with STM32 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3
ST-LINK/V2 status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Software configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1
ST-LINK/V2 firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2
STM8 application development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3
STM32 application development and Flash programming . . . . . . . . . . . . 15
6
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
DocID018748 Rev 7
UM1075
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
List of the order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SWIM flat ribbon connections for ST-LINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SWIM low-cost cable connections for ST-LINK/V2-ISOL . . . . . . . . . . . . . . . . . . . . . . . . . . 11
JTAG/SWD cable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How third-party toolchains support ST-LINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DocID018748 Rev 7
3/19
3
List of figures
UM1075
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
4/19
ST-LINK/V2 and ST-LINK/V2-ISOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ST-LINK/V2 product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ST-LINK/V2-ISOL product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connectors of the ST-LINK/V2 (on the left) and ST-LINK/V2-ISOL (on the right) . . . . . . . . 8
ERNI connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Key detail on connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Low-cost connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Target SWIM connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
JTAG and SWD connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
JTAG debugging flat ribbon layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SWIM ST-LINK/V2 standard ERNI cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SWIM ST-LINK/V2 low-cost cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DocID018748 Rev 7
UM1075
1
Features
Features
•
5 V power supplied by a USB connector
•
USB 2.0 full speed compatible interface
•
USB standard A to Mini-B cable
•
SWIM specific features
•
2
–
1.65 V to 5.5 V application voltage supported on SWIM interface
–
SWIM low-speed and high-speed modes supported
–
SWIM programming-speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in
high speed
–
SWIM cable for connection to the application via an ERNI standard vertical (ref:
284697 or 214017) or horizontal (ref: 214012) connector
–
SWIM cable for connection to the application via a pin header or a 2.54 mm pitch
connector
JTAG/serial wire debugging (SWD) specific features
–
1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V
tolerant inputs
–
JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
–
Supports JTAG communication
–
Supports serial wire debug (SWD) and serial wire viewer (SWV) communication
•
Direct firmware update feature supported (DFU)
•
Status LED which blinks during communication with the PC
•
1000 VRMS high isolation voltage (ST-LINK/V2-ISOL only)
•
Operating temperature 0 to 50 °C
Ordering information
To order the ST-LINK/V2 refer to Table 1:
Table 1. List of the order codes
Order code
ST-LINK description
ST-LINK/V2
In-circuit debugger/programmer
ST-LINK/V2-ISOL
In-circuit debugger/programmer
with digital isolation
DocID018748 Rev 7
5/19
18
Product contents
3
UM1075
Product contents
The cables delivered within the product are showed in Figure 2: ST-LINK/V2 product
contents and Figure 3: ST-LINK/V2-ISOL product contents. They include (from left to right in
Figure 2 and Figure 3):
•
USB standard A to Mini-B cable (A)
•
ST-LINK/V2 debugging and programming (B)
•
SWIM low-cost connector (C)
•
SWIM flat ribbon with a standard ERNI connector at one end (D)
•
JTAG or SWD and SWV flat ribbon with a 20-pin connector (E)
Figure 2. ST-LINK/V2 product contents
B
C
A
6/19
DocID018748 Rev 7
D
E
UM1075
Product contents
Figure 3. ST-LINK/V2-ISOL product contents
C
A
E
D
B
DocID018748 Rev 7
7/19
18
Hardware configuration
4
UM1075
Hardware configuration
The ST-LINK/V2 is designed around the STM32F103C8 device, which incorporates the
high-performance ARM® Cortex®-M3 core. It is available in a TQFP48 package.
As shown in Figure 4, the ST-LINK/V2 provides two connectors:
•
an STM32 connector for the JTAG/SWD and SWV interface
•
an STM8 connector for the SWIM interface
The ST-LINK/V2-ISOL provides one connector for the STM8 SWIM, STM32 JTAG/SWD and
SWV interfaces.
Figure 4. Connectors of the ST-LINK/V2 (on the left) and ST-LINK/V2-ISOL (on the right)
C
A
B
D
D
1. A = STM32 JTAG and SWD target connector
2. B = STM8 SWIM target connector
3. C = STM8 SWIM, STM32 JTAG and SWD target connector
4. D = Communication activity LED
4.1
Connection with STM8 applications
For STM8 developments, the ST-LINK/V2 can be connected to the target board by two
different cables, depending on the connector available on the application board.
These cables are:
8/19
•
SWIM flat ribbon with a standard ERNI connector at one end
•
SWIM cable with two 4-pin, 2.54 mm connector or SWIM separate-wires cable
DocID018748 Rev 7
UM1075
4.1.1
Hardware configuration
Standard ERNI connection with SWIM flat ribbon
Figure 5 shows how to connect the ST-LINK/V2 if a standard ERNI 4-pin SWIM connector is
present on the application board.
Figure 5. ERNI connection
A
A
B
B
C
C
1. A = Target application board with ERNI connector
2. B = Wire cable with ERNI connector at one end
3. C = STM8 SWIM target connector
4. See Figure 11: SWIM ST-LINK/V2 standard ERNI cable.
Figure 6 shows that pin 16 is missing on the ST-LINK/V2-ISOL target connector. This
missing pin is used as a safety key on the cable connector, to guarantee connection of the
SWIM cable in the correct position on the target connector even pins, used for both SWIM
and JTAG cables.
Figure 6. Key detail on connectors
DocID018748 Rev 7
9/19
18
Hardware configuration
4.1.2
UM1075
Low-cost SWIM connection
Figure 7 shows how to connect the ST-LINK/V2 if a 4-pin, 2.54 mm, low-cost SWIM
connector is present on the application board.
Figure 7. Low-cost connection
A
A
B
B
C
C
1. A = Target application board with 4-pin, 2.54 mm, low-cost connector
2. B = Wire cable with a 4-pin connector or separate-wires cable
3. C = STM8 SWIM target connector
4. See Figure 12: SWIM ST-LINK/V2 low-cost cable
10/19
DocID018748 Rev 7
UM1075
4.1.3
Hardware configuration
SWIM signals and connections
Table 2 summarizes the signal names, functions, and target connection signals using the
wire cable with a 4-pin connector.
Table 2. SWIM flat ribbon connections for ST-LINK/V2
Pin no.
Name
Function
Target connection
1
VDD
Target VCC(1)
MCU VCC
2
DATA
SWIM
MCU SWIM pin
3
GND
GROUND
GND
4
RESET
RESET
MCU RESET pin
1. The power supply from the application board is connected to the ST-LINK/V2 debugging and programming
board to ensure signal compatibility between both boards.
Figure 8. Target SWIM connector
Table 3 summarizes the signal names, functions, and target connection signals using the
separate-wires cable.
As the SWIM separate-wires cable has independent connectors for all pins on one side, it is
possible to connect the ST-LINK/V2-ISOL to an application board without a standard SWIM
connector. On this flat ribbon, all signals are referenced by a specific color and a label to
ease the connection on target.
Table 3. SWIM low-cost cable connections for ST-LINK/V2-ISOL
Color
Cable pin name
Function
Target connection
Red
TVCC
Target VCC(1)
MCU VCC
Green
UART-RX
Blue
UART-TX
Unused
Reserved (2)
(not connected on the target board)
Yellow
BOOT0
Orange
SWIM
SWIM
MCU SWIM pin
Black
GND
GROUND
GND
White
SWIM-RST
RESET
MCU RESET pin
1. The power supply from the application board is connected to the ST-LINK/V2 debugging and programming
board to ensure signal compatibility between both boards.
2. BOOT0, UART-TX and UART-RX are reserved for future developments.
DocID018748 Rev 7
11/19
18
Hardware configuration
UM1075
TVCC, SWIM, GND and SWIM-RST can be connected to a low-cost 2.54 mm pitch
connector or to pin headers available on the target board.
4.2
Connection with STM32 applications
For STM32 developments, the ST-LINK/V2 needs to be connected to the application using
the standard 20-pin JTAG flat ribbon provided.
Table 4 summarizes the signals names, functions, and target connection signals of the
standard 20-pin JTAG flat ribbon.
Table 4. JTAG/SWD cable connections
ST-LINK/V2
connector
(CN3)
Pin no.
1
ST-LINK/V2 function
Target connection
(JTAG)
Target connection
(SWD)
VAPP
Target VCC
MCU VDD(1)
MCU VDD(1)
3
TRST
JTAG TRST
JNTRST
GND(2)
4
GND
GND
GND(3)
GND(3)
5
TDI
JTAG TDO
JTDI
GND(2)
6
GND
GND
GND(3)
GND(3)
7
TMS_SWDIO
JTAG TMS, SW IO
JTMS
SWDIO
GND(3)
2
8
GND
GND
GND(3)
9
TCK_SWCLK
JTAG TCK, SW CLK
JTCK
SWCLK
GND(3)
10
GND
GND
GND(3)
11
NC
Not connected
Not connected
Not connected
GND(3)
12
GND
GND
GND(3)
13
TDO_SWO
JTAG TDI, SWO
JTDO
TRACESWO(4)
14
GND
GND
GND(3)
GND(3)
15
NRST
NRST
NRST
NRST
GND(3)
16
GND
GND
GND(3)
17
NC
Not connected
Not connected
Not connected
GND(3)
18
GND
GND
GND(3)
19
VDD
VDD (3.3V)(5)
Not connected
Not connected
GND
GND(3)
GND(3)
20
GND
1. The power supply from the application board is connected to the ST-LINK/V2 debugging and programming
board to ensure signal compatibility between both boards.
2. Connect to GND for noise reduction on the ribbon.
3. At least one of this pin must be connected to the ground for correct behavior (connecting all of them is
recommended).
4. Optional: for Serial Wire Viewer (SWV) trace.
5. Available on ST-LINK/V2 only and not connected on ST-LINK/V2/OPTO.
12/19
DocID018748 Rev 7
UM1075
Hardware configuration
Figure 9 shows how to connect the ST-LINK/V2 to a target using the JTAG cable.
Figure 9. JTAG and SWD connection
A
B
A
B
C
C
1. A = Target application board with JTAG connector
2. B = JTAG/SWD 20-wire flat cable
3. C= STM32 JTAG and SWD target connector
The reference of the connector needed on the target application board is:
2x10C header wrapping 2x40C H3/9.5 (pitch 2.54) - HED20 SCOTT PHSD80.
Figure 10. JTAG debugging flat ribbon layout
9LHZHGIURPDERYH3&%
AI
Note:
For low cost applications or when the standard 20-pins-2.54mm-pitch-connector footprint is
too big, it is possible to implement the Tag-Connect solution to save cost and space on the
application board. The Tag-Connect adapter and cable provide a simple reliable means of
connecting ST-LINK/V2 or ST-LINK/V2-ISOL to the PCB without requiring a mating
DocID018748 Rev 7
13/19
18
Hardware configuration
UM1075
component on application PCB. For more details on this solution and
application-PCB-footprint information, visit www.tag-connect.com.
The references of components compatible with JTAG and SWD interfaces are:
4.3
a)
TC2050-ARM2010 adapter (20-pin- to 10-pin-interface board)
b)
TC2050-IDC or TC2050-IDC-NL (No Legs) (10-pin cable)
c)
TC2050-CLIP retaining clip for use with TC2050-IDC-NL (optional)
ST-LINK/V2 status LEDs
The LED labeled ‘COM’ on top of the ST-LINK/V2 shows the ST-LINK/V2 status (whatever
the connection type).
When the:
14/19
•
LED is blinking RED: the first USB enumeration with the PC is taking place.
•
LED is RED: communication between the PC and ST-LINK/V2 is established (end of
enumeration).
•
LED is blinking GREEN/RED: data are being exchanged between the target and the
PC.
•
LED is GREEN: the last communication has been successful.
•
LED is ORANGE: ST-LINK/V2 communication with the target has failed.
DocID018748 Rev 7
UM1075
Software configuration
5
Software configuration
5.1
ST-LINK/V2 firmware upgrade
The ST-LINK/V2 embeds a firmware upgrade mechanism for in-situ upgrade through the
USB port. As the firmware might evolve during the whole life of the ST-LINK/V2 product
(new functionality, bug fixes, support for new microcontroller families …), it is recommended
to visit www.st.com/stlinkv2 periodically in order to stay up-to-date with the latest firmware
version.
5.2
STM8 application development
Refer to ST toolset Pack24 with Patch 1 or more recent, which includes ST Visual Develop
(STVD) and ST Visual Programmer (STVP).
5.3
STM32 application development and Flash programming
Third-party toolchains, Atollic® TrueSTUDIO, IAR™ EWARM, Keil® MDK-ARM™, and
TASKING VX-toolset support ST-LINK/V2 according to the versions given in Table 5 or in
the most recent version available.
Table 5. How third-party toolchains support ST-LINK/V2
Third party
Atollic®
IAR
™
Keil
®
TASKING
Toolchain
Version
TrueSTUDIO
2.1
EWARM
6.20
MDK-ARM
™
4.20
VX-toolset for ARM® Cortex®-M 4.0.1
The ST-LINK/V2 requires a dedicated USB driver. If the toolset installed it automatically, the
file stlink_winusb.inf is installed in <WINDIR>/inf (where <WINDIR> is typically
C:/Windows).
If the toolset setup did not install it automatically, the driver can be found on www.st.com:
1.
Connect to www.st.com.
2.
In the search tab, part number field, look for ST-LINK/V2.
3.
Click on the Generic Part Number column hyperlink to ST-LINK/V2.
4.
In the Design support tab, SW drivers section, click on the icon to download
st-link_v2_usbdriver.zip.
5.
Unzip and run ST-Link_V2_USBdriver.exe.
For more information on third-party tools, visit the following websites:
•
www.atollic.com
•
www.iar.com
•
www.keil.com
•
www.tasking.com
DocID018748 Rev 7
15/19
18
Schematics
6
UM1075
Schematics
Figure 11. SWIM ST-LINK/V2 standard ERNI cable
7DUJHWERDUG
KRUL]RQWDOPRXQW
67/,1.9 ERDUG
1RWHFRQQHFWRUORFDWHGRQWKH
HGJHRIWKHERDUG
&DEOHOHQJKWPP
/RZFRVW
IHPDO
FRQQHFWRU
(51,
3&%)RRWSULQW
67/,1.9
PDOH
FRQQHFWRU
1RWH%ODFNZLUHORFDWLRQ
3,19''
3,1'$7$
86%
3,1*1'
&1
7DUJHWERDUG
YHUWLFDOPRXQW
3,15(6(7
&1
86%
3&%)RRWSULQW
3&%
DL9
1. Legend for pin descriptions:
VDD = Target voltage sense
DATA = SWIM DATA line between target and debug tool
GND = Ground voltage
RESET = Target system reset
16/19
DocID018748 Rev 7
UM1075
Schematics
Figure 12. SWIM ST-LINK/V2 low-cost cable
67/,1.9
E
RDUG
7DUJHWERDUG
$SSOLFDWLRQPDOH
FRQQHFWRU
/RZFRVW
IHPDO
FRQQHFWRU
&DEOHOHQJKW PP
/RZFRVW
IHPDO
FRQQHFWRU
67/,1.9
PDOH
FRQQHFWRU
3&%
3,Q9''
3,Q9''
3,Q'$7$
3,Q'$7$
3,Q*1'
3,Q*1'
3,Q5(6(7
86%
3,Q5(6(7
&1
&1
86%
3&%
3&%
DL9
1. Legend for pin descriptions:
VDD = Target voltage sense
DATA = SWIM DATA line between target and debug tool
GND = Ground voltage
RESET = Target system reset
DocID018748 Rev 7
17/19
18
Revision history
7
UM1075
Revision history
Table 6. Document revision history
18/19
Date
Revision
Changes
22-Apr-2011
1
Initial release.
03-Jun-2011
2
Table 2: SWIM flat ribbon connections for ST-LINK/V2: added
footnote 1 to the function “Target VCC”.
Table 4: JTAG/SWD cable connections: added footnote to the
function “Target VCC”.
Table 5: How third-party toolchains support ST-LINK/V2: updated the
“Versions” of IAR and Keil.
19-Aug-2011
3
Added USB driver details to Section 5.3.
11-May-2012
4
Added SWD and SWV to JTAG connection features. Modified
Table 4: JTAG/SWD cable connections.
13-Sep-2012
5
Added ST-LINK/V2-ISOL order code.
Updated Section 4.1: STM8 application development on page 15
Added Note 5. in Table 4.
Added Note “For low cost applications...” before Section 3.3: STLINK/V2 status LEDs on page 14
18-Oct-2012
6
Added Section 5.1: ST-LINK/V2 firmware upgrade on page 15.
25-Mar-2016
7
Updated Vrms value in Introduction and in Features.
DocID018748 Rev 7
UM1075
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics – All rights reserved
DocID018748 Rev 7
19/19
19