CLRM701 MIFARE and ICODE contactless reader module

CLRM701
Mifare® & ICODE contactless reader module
Rev. 3.2 — 24 May 2007
Product data sheet
101432
PUBLIC
1. General description
This document describes the functionality of the CLRM701 reader module. It includes the
functional and electrical specifications and gives the needed details to use this reader
module as a reference design.
This reader module is designed for an easy adaptation of a contactless reader to a PC
and it is ready to design a new application giving the basic hints for a reader hardware
development.
The CLRM701 contactless reader module is part of the CLRD701, the Mifare® PEGODA
reader. It uses the CLRC632 reader IC for the contactless communication. The CLRC632
is member of a family for highly integrated reader ICs for contactless communication at
13.56 MHz.
2. Features
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
contactless smart card reader module
based on the CLRC632
contactless operating frequency 13.56 MHz
Supports Mifare® Dual Interface Card ICs and ISO 14443A part 1- 4
Supports ISO 14443B
Supports Mifare® Classic crypto
Supports ISO 15693
Supports NXP ICODE
Supports higher data rates of up to 424 kbit/s
Typical operating distance: 75 - 100mm
CE and FCC compliant
USB host interface
USB bus powered 5 VDC power supply
Unique serial number of each reader device
Supported by Windows 2000 and Windows XP.
3. Ordering information
This module is part of the CLRD701 reader. It cannot be ordered separately.
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
4. Block diagram
.
The CLRD701 PEGODA reader is a complete reader based on the CLRM701. The reader
itself is divided in two parts:
• CLRM701, This reader module is the basic print including the CLRC632, a
µ-Controller and all interfaces to a host.
• MF AN700 (flexible PEGODA antenna), This antenna is described in the application
note Ref. 2.
CLRD701 block diagram (Figure 1) shows the CLRD701 PEGODA’s basic functional
components
CLRM701
MFAN700
Antenna
Reset
CLRC632
µ Controller
Flash
1...8Mbit
Debug
Contactless
Reader IC
Power
Management
USB
IDLE
CON1
USB
Fig 1. CLRD701 PEGODA block diagram
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
2 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
The PEGODA reader is designed to offer the user a great freedom to design an
application. Several functional blocks can be identified.
Core component of the PEGODA is the CLRC632, the highly integrated ISO 14443, ISO
15693 reader IC. For detailed information concerning the CLRC632 please refer to the
data sheet Ref. 1. The CLRC632 is used as an analog front-end unit to communicate via
the antenna to a contactless chip card. All relevant data coding to send and receive data
according to the ISO 14443 and ISO 15693 is done internally by the CLRC632. The
CLRC632 itself is controlled by a µ-controller.
The µ-controller handles the communication to the host PC via USB. The µ-Controller
translates the serial protocol via USB into remote function calls and executes the
appropriate command. To be able to implement the complete Mifare® Classic protocol, the
ISO 14443-4 open protocol commands as well as ISO 15693 and the host communication
protocol is implemented in a 1.8 Mbit flash device.
Furthermore, a reset and a power management circuit and several ports are provided for
debug purposes.
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
3 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
5. Functional description
The default configuration for the PEGODA reader offers an USB interface to the host.
Table 1 defines possible interface connection types of CLRM701 module and CLRD701
PEGODA reader.
Table 1.
Host interface types
Host interface
type
CLRD701
PEGODA reader
CLRM701 reader
module
USB Type B plug
yes
yes
5.1 USB Type B Plug
The USB type B plug is the default configuration of the PEGODA reader to connect the
reader to a host PC.
Fig 2. USB Type B connectors
The default configuration uses the USB cable to communicate to the PEGODA as well as
to supply the 5 V supply voltage.
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
4 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
5.2 Power supply
The controller board supports various power supply sources, which have to provide a
regulated 5V DC voltage. Figure 3 shows the possible power supply on the CLRM701.
In the default configuration, the PEGODA reader is a USB bus powered reader. No
external power supply has to be connected.
USB
Power Supply
DC
Power Connector
RJ45 socket
RS232 power supply
via special cable
configuration
Fig 3. Interface and power supply
Remark: In order to fulfil the USB specification version 1.1, the reader module behaves
like a low power device after power on. Having sent an ACTIVATE command, the
PEGODA is activated and the reader module switches to an idle state resulting in an
increased power consumption. Only one power source must be connected to the board.
5.3 Boot jumper and serial I/O
The PEGODA reader offers a boot jumper to enable a firmware update as well as several
serial I/O pins to fulfil different user and application specific requirements. Figure 4 shows
the location of the boot jumper and the serial I/O pins.
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
5 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Serial IO
Boot Jumper
misc. Port
Pins
Fig 4. Boot jumper and I/O pins location
5.3.1 Boot jumper
Setting the boot jumper before the board is connected to the power supply, the
µ-controller enables the internal bootstrap mechanism. This might be used to download
new firmware via the serial interface without additional hardware changes. For detailed
description of the µ-controller please refer to the controller’s data sheet.
5.3.2 Serial I/O
The serial I/O pins allow the user to monitor additional controller lines to fulfil
application-related requirements. Table 2 describes the I/O pins.
Table 2.
I/O pin description
Pin No. Description
1
+ 3.3 V regulated; Controller power supply
2
RxD; asynchronous receive pin; TTL level
3
TxD; asynchronous transmit pin; TTL level
4
DSR; data set ready; asynchronous serial handshake pin; TTL level; synchronous serial
Master-Receive/Slave-Transmit
5
DTR; data terminal ready; asynchronous serial hand shake pin; TTL level
6
GND
7
port 3.9; synchronous serial Master-Transmit/Slave-Receive
8
port 3.13; synchronous serial Master-Clock-Out/Slave-Clock-In
9
reset out; microcontroller reset out pin
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
6 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
5.3.3 Miscellaneous Port Pins
In addition to the I/O pins several miscellaneous port pins can be used to monitor and
control the µ-controllers behaviour. Table 3 lists the miscellaneous port pins.
Table 3.
Miscellaneous port pins
Pin No.
Description
1
+ 3.3 V regulated; Controller power supply
2
port 6.2; Chip Select Line 2;
3
port 2.1; fast external interrupt line 2
4
port 6.3; Chip Select Line 3;
5
Reset In; microcontroller reset in; negative logic
6
GND
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
7 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
6. CLRM701 PCB description
The following parts describe the CLRM701 schematic, the part list and the layout of the
PCB completely in order to give the user the possibility to take the PEGODA reader as a
reference design for an own reader development.
6.1 Schematic
Fig 5. CLRM701 Schematic left part
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
8 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
CLRC632
Fig 6. CLRM701 Schematic right part
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
9 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
6.2 Part list
The part list gives a complete overview about the used components. If no supplier or order
number is given these parts are standard components.
Parts are subject to multi-sourcing and can be replaced with equivalent part without
notice.
Table 4.
Part list CLRM701
Qty
Part
Value
Package
Remarks
CLRM701
1
PCB
72x72
scratched edges
X
1
ANT
PHD1x8
1X08
single pin row
X
1
BOOT
2
C1, C2
PHD1x2
JP1
bootstrap jumper
X
68p
C0805
NPO, 2 %
X
2
C3, C6
100p
C0805
NPO, 5 %
X
2
C4, C5
10n
C0805
X7R
X
2
C7, C8
33p
C0805
NPO, 5 %
X
1
C9
10n
C0805
X7R
X
1
C10
100p
C0805
NPO, 5 %
X
1
C11
100n
C0805
NPO, 10 %
X
1
C12
47p
C0805
NPO, 5 %
X
17
C14, C16, C17, C18, C19, C20,
C21, C22, C23, C24, C25, C26,
C41, C42, C43, C44, C45
100n
C0805
X7R
X
7
C15, C27, C28, C29, C30, C37,
C46
100n
C0805
X7R
n.a.
1
C31
4.7n
C0805
X7R
X
2
C32, C33
2.2µ
C0805
ceramic decoupling capacitance 6,3 V
X
10 %
1
C34
220n
C0805
X7R
X
4
C35, C36, C50, C51
10n
C0805
X7R
X
2
C38, C48
33µ,10V
TANTAL-D
Tantal
X
1
C39
1n
C0805
NPO, 10 %
X
1
C40
22n
C0805
NPO, 5 %
n.a.
2
C47, C49
option
ES-2,5
optional to part C38, C48
X
1
C52
10p
C0805
NPO, 5 %
1
CON1
USB Type B
RWD61729 USB, Type B, socket
X
1
CON2
DC PWR
socket
HOHLB02
n.a.
X
DC power socket,
outer diam. 5,5 mm
inner diam. 2,5 mm
1
CON3
DB9 socket
F09H
9 pol. DSub Socket
n.a.
1
CON4
RJ45LSMD
socket
555764-1
RJ45 Connector for RS232, Power,
USB
n.a.
1
D1
TOP-LED
PLCC2
SMD LED green, PLCC2 package
X
1
D2
5,6
DIO-MINI
BZV55C 5,6 V SOD-80, MINIMELF
X
1
D3
DKKSOT23
SOT23C
Schottky Diode 30 V SOT23 BAT64-05
n.a.
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
10 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Table 4.
Part list CLRM701
Qty
Part
Value
Package
Remarks
CLRM701
1
DBG
PHD2x8
FE08-2
1
IC1
C161U_M
TQFP-100
SAB-C161U-LF V1.3
X
1
IC2
AM29F800B
TSOP48
(A)M29F400B
X
1
IC3
MAX232
SO16
MAX232ECSE
n.a.
1
IC4
TC554161
TSOPII54
SRAM, TC554161AFT-V
n.a.
1
IC5
DSS30655
EMI
EMI filter, DSS30655Y5S102M100
X
1
IC7
MC33465N
SOT-23-5
Reset IC, MC33465N-27atr
X
1
IC9
RC632
SO-32L
CL RC 632
X
1
IDLE
PHD1x6
FE06
2
L1, L2
1µH
L_NL322
n.a.
n.a.
NL322522T-1R0J, 5%
X
Substitute Resistor 0R
X
2
L3, L4
470nH
3
L5, L6, L7
0
X
2
L8, L10
100nH
X
1
L9
22nH
X
1
OPTION
option
TO220V
optional equipment for part VR1
X
1
Q1
13.56MHz
HC49U-V
SMD-Quarz, HC 49 US SMD, 13,56
MHz SMD or through hole contacts
X
1
QU1
option
HC49U-V
optional for part Q1
X
1
Q2
8MHz
SD3
SMD-Quarz, HC 49 US SMD, 8MHz,
SMD or through hole contacts
X
1
QU2
option
SD3
optional for part Q2
X
1
R1
820
R0805
NPO, 1 %
X
1
R2
560
R0805
NPO, 1 %
X
1
R3
470
R0805
5%
X
12
R4, R5, R6, R14, R15, R16, R17, 10k
R37, R38, R39, R40, R41
R0805
5%
X
1
R7
82
R0805
5%
X
2
R10, R12
27
R0805
1%
X
1
R11
11k
R0805
2%
n.a.
1
R13
1k5
R0805
5%
X
5
R18, R21, R42, R50, R53
0
R0805
1
R43
820
R0805
2
S1, S2
2
X
1%
n.a.
Screw
2.5x7 mm tin screw
X
S1I, S2I
Isolate
screw isolation foil
X
1
SERIO
PHD1x9
FE09
1
T1
BCR108
SOT-23
1
VR1
LT1086_SMD DDPAK
n.a.
switching transistor
X
voltage regulator 3.3 V SMD
(LT1086CM-3.3) or through hole
contacts (LT1086CT-3.3)
X
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
11 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
6.3 Layout
The CLRM701 is designed using a four layer PCB. The following Figure 7 to Figure 12
show the component placements and all other layers.
Fig 7. CLRM701 Complete Component Placement
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
12 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Fig 8.
CLRM701 Top Layer
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
13 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Fig 9.
CLRM701 Supply Layer
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
14 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Fig 10. CLRM701 Ground Layer
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
15 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Fig 11. CLRM701 Bottom Layer
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
16 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
Fig 12. CLRM701 Top and Bottom View
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
17 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
7. Recommended operating conditions
Table 5.
Recommended operating conditions
Symbol
Parameter
Conditions
Tamb
ambient temperature
VDD
DC Supply Voltage
DVSS = 0V
Min
Type
Max
Unit
-10
+25
+70
°C
4.5
5.0
5.5
V
8. Characteristics
Table 6.
USB- characteristics
Symbol
Parameter
Conditions
Min
Type
Max
Unit
USB- baud
USB- baudrate
cable length max. 3 m
-
12
-
Mbaud
9. Current consumption
Table 7.
Current consumption
Symbol
Parameter
Conditions
Min
Type
Max
Unit
IDVDD
supply current
StandBy
-
70
-
mA
IDVDD
supply current
Idle, RF off
-
160
-
mA
IDVDD
supply current
Idle, RF on
-
250
-
mA
10. Operating distance
Table 8.
Operating distance
Symbol
Parameter
Conditions
Min
Type
Max
Unit
OD
operating distance
used antenna : MFAN700, measured from the middle of
the reader surface
-
75
-
mm
11. Support information
For additional information, please visit http.//www.nxp.com
12. References
[1]
Mifare® & ICODE CLRC632 Multiple protocol contactless reader IC
[2]
Mifare® MFRM700 Antenna and matching adapter description
To download referred documents please visit http://www.nxp.com
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
18 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
13. Revision history
Table 9.
Revision history
Document ID Release date
Data sheet status Change notice
Supersedes
101432
Product data
sheet
3.1
Modifications:
24 May 2007
•
The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP
Semiconductors.
•
Legal texts have been adapted to the new company name.
101431
November
2004
Product data
sheet
101430
July 2004
Product data
sheet
101420
April 2004
initial version
Add ordering info, Addition to feature set
2.0
101432
Product data sheet
3.0
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
19 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
14. Legal information
14.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
14.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a NXP Semiconductors product can reasonably be expected to
result in personal injury, death or severe property or environmental damage.
NXP Semiconductors accepts no liability for inclusion and/or use of NXP
Semiconductors products in such equipment or applications and therefore
such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Mifare® — is a trademark of NXP B.V.
15. Contact information
For additional information, please visit: http://www.nxp.com
For sales office addresses, send an email to: [email protected]
101432
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.2 — 24 May 2007
20 of 21
CLRM701
NXP Semiconductors
Mifare® & ICODE contactless reader module
16. Tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Host interface types . . . . . . . . . . . . . . . . . . . . . .4
I/O pin description . . . . . . . . . . . . . . . . . . . . . . .6
Miscellaneous port pins . . . . . . . . . . . . . . . . . . .7
Part list CLRM701 . . . . . . . . . . . . . . . . . . . . . .10
Recommended operating conditions . . . . . . . .18
Table 6.
Table 7.
Table 8.
Table 9.
USB- characteristics . . . . . . . . . . . . . . . . . . . . 18
Current consumption . . . . . . . . . . . . . . . . . . . . 18
Operating distance. . . . . . . . . . . . . . . . . . . . . . 18
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 19
17. Figures
Fig 1.
Fig 2.
Fig 3.
Fig 4.
Fig 5.
Fig 6.
CLRD701 PEGODA block diagram . . . . . . . . . . .2
USB Type B connectors. . . . . . . . . . . . . . . . . . . . .4
Interface and power supply . . . . . . . . . . . . . . . . . .5
Boot jumper and I/O pins location . . . . . . . . . . . . .6
CLRM701 Schematic left part . . . . . . . . . . . . . . . .8
CLRM701 Schematic right part . . . . . . . . . . . . . . .9
Fig 7.
Fig 8.
Fig 9.
Fig 10.
Fig 11.
Fig 12.
CLRM701 Complete Component Placement . . . 12
CLRM701 Top Layer . . . . . . . . . . . . . . . . . . . . . 13
CLRM701 Supply Layer . . . . . . . . . . . . . . . . . . . 14
CLRM701 Ground Layer . . . . . . . . . . . . . . . . . . 15
CLRM701 Bottom Layer. . . . . . . . . . . . . . . . . . . 16
CLRM701 Top and Bottom View . . . . . . . . . . . . 17
14.4
15
16
17
18
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18. Contents
1
2
3
4
5
5.1
5.2
5.3
5.3.1
5.3.2
5.3.3
6
6.1
6.2
6.3
7
8
9
10
11
12
13
14
14.1
14.2
14.3
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional description . . . . . . . . . . . . . . . . . . . 4
USB Type B Plug . . . . . . . . . . . . . . . . . . . . . . . 4
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Boot jumper and serial I/O . . . . . . . . . . . . . . . . 5
Boot jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Serial I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Miscellaneous Port Pins . . . . . . . . . . . . . . . . . . 7
CLRM701 PCB description . . . . . . . . . . . . . . . . 8
Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Part list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Recommended operating conditions. . . . . . . 18
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 18
Current consumption . . . . . . . . . . . . . . . . . . . 18
Operating distance . . . . . . . . . . . . . . . . . . . . . 18
Support information . . . . . . . . . . . . . . . . . . . . 18
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 19
Legal information. . . . . . . . . . . . . . . . . . . . . . . 20
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 20
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
20
20
21
21
21
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2007.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 24 May 2007
Document identifier: 101432