10A/120W

MQFL-270-12S
Single Output
H igH R eliability DC-DC C onveRteR
155-400V
155-475V
12V
10A
86% @ 5A / 88% @ 10A
Continuous Input
Transient Input
Output
Output
Efficiency
F ull P oweR o PeRation : -55ºC
to
+125ºC
The MilQor® series of high-reliability DC-DC converters
brings SynQor’s field proven high-efficiency synchronous
rectifier technology to the Military/Aerospace industry.
SynQor’s innovative QorSeal® packaging approach ensures
survivability in the most hostile environments. Compatible
2
ENA
with the industry standard format, these converters operate
RE
SHA
at a fixed frequency, have no opto-isolators, and follow
conservative component derating guidelines.
2
70-1
+VIN
They are
E
CAS
1
ENA
10
X
o
E 1W
DC- in 12V
CAG
01
V
0
05-3
2
7
3
2
D/C
T
C OU
SYN
C IN
SYN
military standards.
-SNS
RTN
OUT
T
+VOU
r
tE
2
FL- VEr
MQ DC Con ut@10A
N
IN RT
designed and manufactured to comply with a wide range of
+SNS
-ES
S-Y
0
000
000
S/n
Design Process
MQFL series converters are:
• Designed for reliability per NAVSO-P3641-A guidelines
• Designed with components derated per:
— MIL-HDBK-1547A
— NAVSO P-3641A
Qualification Process
MQFL series converters are qualified to:
• MIL-STD-810F
— consistent with RTCA/D0-160E
• SynQor’s First Article Qualification
— consistent with MIL-STD-883F
• SynQor’s Long-Term Storage Survivability Qualification
• SynQor’s on-going life test
In-Line Manufacturing Process
• AS9100 and ISO 9001 certified facility
• Full component traceability
• Temperature cycling
• Constant acceleration
• 24, 96, 160 hour burn-in
• Three level temperature screening
Product# MQFL-270-12S
Phone 1-888-567-9596
DesigneD & ManufactureD in the usa
featuring Qorseal® hi-rel asseMbly
Features
•
•
•
•
•
•
•
Fixed switching frequency
No opto-isolators
Parallel operation with current share
Remote sense
Clock synchronization
Primary and secondary referenced enable
Continuous short circuit and overload protection
with auto-restart feature
• Input under-voltage and over-voltage shutdown
Specification Compliance
MQFL series converters (with MQME filter) are designed to meet:
• MIL-HDBK-704-7 (A through F)
• RTCA/DO-160 Section 16, 17, 18
• MIL-STD-1275 (B, D)
• DEF-STAN 61-5 (part 6)/(5, 6)
• MIL-STD-461 (C, D, E, F)
• RTCA/DO-160(E, F, G) Section 22
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 1
MQFL-270-12S
Output: 12V
Current: 10A
Technical Specification
BLOCK DIAGRAM
REGULATION STAGE
ISOLATION STAGE
CURRENT
SENSE
1
+Vin
7
+Vout
T1
T1
INPUT
RETURN
T2
3
CASE
GATE DRIVERS
T2
ISOLATION BARRIER
2
8
OUTPUT
RETURN
GATE DRIVERS
UVLO
OVSD
CURRENT
LIMIT
4
ENABLE 1
PRIMARY
CONTROL
5
MAGNETIC
12
ENABLE 2
SYNC OUT
11
DATA COUPLING
6
SECONDARY
CONTROL
SYNC IN
SHARE
10
BIAS POWER
+ SENSE
CONTROL
POWER
9
− SENSE
TRANSFORMER
TYPICAL CONNECTION DIAGRAM
270 Vdc
+
__
open
means
on
Product# MQFL-270-12S
ENA 2 12
SHARE 11
1
+VIN
2
IN RTN
3
CASE
4
ENA 1
5
SYNC OUT
6
SYNC IN
Phone 1-888-567-9596
MQFL
www.SynQor.com
+SNS 10
-SNS 9
OUT RTN 8
+VOUT 7
Doc.# 005-0005076 Rev. E
open
means
on
+
Load
__
01/04/16
Page 2
MQFL-270-12S
Output: 12V
Current: 10A
Technical Specification
MQFL-270-12S ELECTRICAL CHARACTERISTICS
Parameter
Min. Typ. Max. Units Notes & Conditions
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Reverse Bias (Tcase = 125ºC)
Reverse Bias (Tcase = -55ºC)
Isolation Voltage (I/O to case, I to O)
Continuous
Transient (≤100µs)
Operating Case Temperature
Storage Case Temperature
Lead Temperature (20s)
Voltage at ENA1, ENA2
INPUT CHARACTERISTICS
Operating Input Voltage Range
“
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Input Over-Voltage Shutdown
Turn-Off Voltage Threshold
Turn-On Voltage Threshold
Shutdown Voltage Hysteresis
Input Filter Component Values (L\C)
Maximum Input Current
No Load Input Current (operating)
Disabled Input Current (ENA1)
Disabled Input Current (ENA2)
Input Terminal Current Ripple (pk-pk)
OUTPUT CHARACTERISTICS
Output Voltage Set Point (Tcase = 25ºC)
Output Voltage Set Point Over Temperature
Output Voltage Line Regulation
Output Voltage Load Regulation
Total Output Voltage Range
Output Voltage Ripple and Noise Peak to Peak
Operating Output Current Range
Operating Output Power Range
Output DC Current-Limit Inception
Short Circuit Output Current
Back-Drive Current Limit while Enabled
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
DYNAMIC CHARACTERISTICS
Output Voltage Deviation Load Transient
For a Pos. Step Change in Load Current
For a Neg. Step Change in Load Current
Settling Time (either case)
Output Voltage Deviation Line Transient
For a Pos. Step Change in Line Voltage
For a Neg. Step Change in Line Voltage
Settling Time (either case)
Turn-On Transient
Output Voltage Rise Time
Output Voltage Overshoot
Turn-On Delay, Rising Vin
Turn-On Delay, Rising ENA1
Turn-On Delay, Rising ENA2
EFFICIENCY
Iout = 10A (155Vin)
Iout = 5A (155Vin)
Iout = 10A (270Vin)
Iout = 5A (270Vin)
Iout = 10A (400Vin)
Iout = 5A (400Vin)
Load Fault Power Dissipation
Short Circuit Power Dissipation
Product# MQFL-270-12S
Group A
Subgroup
Vin=270V dc ±5%, Iout=10A, CL=0µF, free running (see Note 10)
unless otherwise specified
Specifications subject to change without notice
-500
-800
-55
-65
-1.2
600
550
-0.8
-1.2
V
V
V
V
500
800
125
135
300
50
V
V
°C
°C
°C
V
155
155
270
270
400
475
V
V
142
133
5
150
140
11
155
145
17
V
V
V
490
450
20
520
475
50
56\0.11
550
500
80
28
1
6
140
11.88
11.82
-20
50
11.76
0
0
10.5
-900
-2000
-2200
12.00
12.00
0
65
12.00
25
1
38
4
12
180
75
3,000
-600
600
300
900
500
mV
mV
µs
450
2000
2200
600
mV
mV
µs
6
0
75
5
2
10
2
120
10
4
ms
%
ms
ms
ms
36
36
%
%
%
%
%
%
W
W
50
84
84
83
81
80
76
Phone 1-888-567-9596
89
89
88
86
86
82
19
24
See Note 1
HB Grade Products, See Notes 2 & 16
Continuous
Transient, 1s
See Note 3
1, 2, 3
1, 2, 3
1, 2, 3
See Note 3
V
V
V
μH\μF Internal Values
A
Vin = 155V; Iout = 10A
mA
mA
mA
mA
Bandwidth = 100kHz – 10MHz; see Figure 14
V
V
mV
mV
V
mV
A
W
A
A
A
mA
µF
11.5
14
3.1
10
12.12
12.18
20
80
12.24
50
10
120
12.5
(see Note 13)
See Note 5
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
Vout at sense leads
“
“
“ ; Vout @ (Iout=0A) - Vout @ (Iout=10A)
“
Bandwidth = 10MHz; CL=11µF
1
2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
1, 2, 3
1, 2, 3
See Note 5
See Note 4
Vout ≤ 1.2 V; see Note 15
See Note 6
Total Iout step = 5A‹-›10A, 1A‹-›5A; CL=11µF
“
See Note 7
Vin step = 155V‹-›400V; CL=11µF; see Note 8
4, 5, 6
4, 5, 6
Iout = 5A; See Note 7
Vout = 1.2V-›10.8V
4, 5, 6
See Note 5
4, 5, 6
4, 5, 6
4, 5, 6
ENA1, ENA2 = 5V; see Notes 9 & 12
ENA2 = 5V; see Note 12
ENA1 = 5V; see Note 12
1, 2, 3
Iout at current limit inception point; See Note 4
Vout ≤ 1.2V
www.SynQor.com
Doc.# 005-0005076 Rev. E
1
See Note 5
01/04/16
Page 3
MQFL-270-12S
Output: 12V
Current: 10A
Technical Specification
MQFL-270-12S ELECTRICAL CHARACTERISTICS (Continued)
Parameter
Min. Typ. Max. Units Notes & Conditions
Vin=270V dc ±5%, Iout=10A, CL=0µF, free running (see Note 10)
unless otherwise specified
Specifications subject to change without notice
ISOLATION CHARACTERISTICS
Isolation Voltage
Input RTN to Output RTN
Any Input Pin to Case
Any Output Pin to Case
Isolation Resistance (in rtn to out rtn)
Isolation Resistance (any pin to case)
Isolation Capacitance (in rtn to out rtn)
FEATURE CHARACTERISTICS
Switching Frequency (free running)
Synchronization Input
Frequency Range
Logic Level High
Logic Level Low
Duty Cycle
Synchronization Output
Pull Down Current
Duty Cycle
Enable Control (ENA1 and ENA2)
Off-State Voltage
Module Off Pulldown Current
On-State Voltage
Module On Pin Leakage Current
Pull-Up Voltage
RELIABILITY CHARACTERISTICS
Calculated MTBF (MIL-STD-217F2)
GB @ Tcase = 70ºC
AIF @ Tcase = 70ºC
WEIGHT CHARACTERISTICS
Device Weight
Group A
Subgroup
(see Note 13)
Dielectric strength
500
500
500
100
100
V
V
V
MΩ
MΩ
nF
1
1
1
1
1
1
600
kHz
1, 2, 3
500
2.0
-0.5
20
700
5.5
0.8
80
kHz
V
V
%
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
20
25
80
mA
%
44
500
550
0.8
80
2
3.2
4.0
20
4.8
V
µA
V
µA
V
2600
300
103 Hrs.
103 Hrs.
79
g
VSYNC OUT = 0.8V
Output connected to SYNC IN of other MQFL unit
See Note 5
See Note 5
1, 2, 3
See Note 5
1, 2, 3
See Note 5
1, 2, 3
Current drain required to ensure module is off
Imax drawn from pin allowed, module on
See Figure A
Electrical Characteristics Notes
1. Converter will undergo input over-voltage shutdown.
2. Derate output power to 50% of rated power at Tcase = 135º C. Derate output power to 50% of rated power at Tcase = 135ºC.
3. High or low state of input voltage must persist for about 200µs to be acted on by the lockout or shutdown circuitry.
4. Current limit inception is defined as the point where the output voltage has dropped to 90% of its nominal value.
5. Parameter not tested but guaranteed to the limit specified.
6. Load current transition time ≥ 10µs.
7. Settling time measured from start of transient to the point where the output voltage has returned to ±1% of its final value.
8. Line voltage transition time ≥ 250µs.
9. Input voltage rise time ≥ 250µs.
10. Operating the converter at a synchronization frequency above the free running frequency will slightly reduce the converter’s efficiency and may also cause
a slight reduction in the maximum output current/power available. For more information consult the factory.
11. SHARE pin outputs a power failure warning pulse during a fault condition. See Current Share section of the Control Features description.
12. After a disable or fault event, module is inhibited from restarting for 300ms. See Shut Down section of the Control Features description.
13. Only the ES and HB grade products are tested at three temperatures. The C grade products are tested at one temperature. Please refer to the
Construction and Environmental Stress Screening Options table for details.
14. These derating curves apply for the ES and HB grade products. The C- grade product has a maximum case temperature of 70ºC and a maximum
junction temperature rise of 20ºC above TCASE.
15. Converter delivers current into a persisting short circuit for up to 1 second. See Current Limit in the Application Notes section.
16. The specified operating case temperature for ES grade products is -45ºC to 100ºC. The specified operating case temperature for C- grade
products is 0ºC to 70ºC.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 4
MQFL-270-12S
Output: 12V
Current: 10A
Technical Figures
95
95
90
90
85
85
Efficiency (%)
100
Efficiency (%)
100
80
75
70
270 Vin
400 Vin
270 Vin
400 Vin
60
0
1
2
3
4
5
6
Load Current (A)
7
8
9
10
Figure 1: Efficiency at nominal output voltage vs. load current for
minimum, nominal, and maximum input voltage at TCASE=25°C.
-55°C
22
22
20
20
18
18
16
16
14
12
10
8
6
155 Vin
4
-15°C
5°C
25°C
45°C
65°C
Case Temperature (ºC)
85°C
105°C
125°C
14
12
10
8
6
155 Vin
4
270 Vin
2
-35°C
Figure 2: Efficiency at nominal output voltage and 60% rated power vs.
case temperature for input voltage of 155V, 270V and 400V.
Power Dissipation (W)
Power Dissipation (W)
155 Vin
65
60
270 Vin
2
400 Vin
0
400 Vin
0
0
1
2
3
4
5
6
Load Current (A)
7
8
9
10
Figure 3: Power dissipation at nominal output voltage vs. load current
for minimum, nominal, and maximum input voltage at Tcase=25°C.
-55°C
168
16
12
144
14
10
120
96
6
72
4
48
Tjmax = 105º C
Tjmax = 125º C
2
0
45
65
85
105
Case Temperature (ºC)
125
Product# MQFL-270-12S
Phone 1-888-567-9596
45°C
65°C
85°C
105°C
125°C
8
6
4
270 Vin
0
145
Figure 5: Output Current / Output Power derating curve as a function of
Tcase and the Maximum desired power MOSFET junction temperature
(see Note 14). Vin = 270V
25°C
Case Temperature (ºC)
2
0
25
5°C
10
24
Tjmax = 145º C
-15°C
12
Output Voltage (V)
8
-35°C
Figure 4: Power dissipation at nominal output voltage and 60% rated
power vs. case temperature for input voltage of 155V, 270V and 400V.
14
Pout (W)
Iout (A)
75
70
155 Vin
65
80
0
2
4
6
Load Current (A)
8
10
12
Figure 6: Output voltage vs. load current showing typical current limit
curves. See Current Limit section in the Application Notes.
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 5
MQFL-270-12S
Output: 12V
Current: 10A
Technical Figures
Figure 7: Turn-on transient at full resistive load and zero output
capacitance initiated by ENA1. Input voltage pre-applied. Ch 1: Vout
(5V/div). Ch 2: ENA1 (5V/div).
Figure 8: Turn-on transient at full resistive load and 3mF output
capacitance initiated by ENA1. Input voltage pre-applied. Ch 1: Vout
(5V/div). Ch 2: ENA1 (5V/div).
Figure 9: Turn-on transient at full resistive load and zero output
capacitance initiated by ENA2. Input voltage pre-applied. Ch 1: Vout
(5V/div). Ch 2: ENA2 (5V/div).
Figure 10: Turn-on transient at full resistive load and zero output
capacitance initiated by Vin. ENA1 and ENA2 both previously high. Ch
1: Vout (5V/div). Ch 2: Vin (100V/div).
Figure 11: Output voltage response to step-change in load current 50%100%-50% of Iout (max). Load cap: 1µF ceramic cap and 10µF, 100mΩ
ESR tantalum cap. Ch 1: Vout (500mV/div). Ch 2: Iout (5A/div).
Figure 12: Output voltage response to step-change in load current 10%50%-10% of Iout (max). Load cap: 1µF ceramic cap and 10µF, 100mΩ
ESR tantalum cap. Ch 1: Vout (500mV/div). Ch 2: Iout (5A/div).
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 6
MQFL-270-12S
Output: 12V
Current: 10A
Technical Figures
Figure 13: Output voltage response to step-change in input voltage (155V 400V - 155V) in 250 μS. Load cap: 10µF, 100mΩ ESR tantalum cap and 1µF
ceramic cap. Ch 1: Vout (1V/div). Ch 2: Vin (100V/div).
Figure 14: Test set-up diagram showing measurement points for Input
Terminal Ripple Current (Figure 15) and Output Voltage Ripple (Figure
16).
Figure 15: Input terminal current ripple, ic, at full rated output current
and nominal input voltage with SynQor MQ filter module (50mA/div).
Bandwidth: 20MHz. See Figure 14.
Figure 16: Output voltage ripple, Vout, at nominal input voltage and
rated load current (20mV/div). Load capacitance: 1µF ceramic capacitor
and 10µF tantalum capacitor. Bandwidth: 10MHz. See Figure 14.
Figure 17: Rise of output voltage after the removal of a short circuit
across the output terminals. Ch 1: Vout (5V/div). Ch 2: Iout (2A/div).
Figure 18: SYNC OUT vs. time, driving SYNC IN of a second SynQor
MQFL converter. Ch1: SYNC OUT: (1V/div).
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 7
MQFL-270-12S
Output: 12V
Current: 10A
Technical Figures
0
1
Forward Transmission (dB)
Output Impedance (ohms)
-10
0.1
0.01
155Vin
270Vin
400Vin
0.001
10
100
1,000
Hz
10,000
5
-30
-40
-50
-60
-70
-80
155Vin
-90
400Vin
270Vin
-100
100,000
Figure 19: Magnitude of incremental output impedance (Zout = vout/
iout) for minimum, nominal, and maximum input voltage at full rated
power.
-20
10
100
1,000
Hz
10,000
100,000
Figure 20: Magnitude of incremental forward transmission (FT = vout/
vin) for minimum, nominal, and maximum input voltage at full rated
power.
10000
-5
1000
Input Impedance (ohms)
Reverse Transmission (dB)
0
-10
-15
-20
-25
-30
-35
155Vin
-40
100
155Vin
270Vin
10
400Vin
270Vin
400Vin
-45
-50
1
10
100
1,000
Hz
10,000
100,000
10
100
1,000
Hz
10,000
100,000
Figure 21: Magnitude of incremental reverse transmission (RT = iin/iout)
for minimum, nominal, and maximum input voltage at full rated power.
Figure 22: Magnitude of incremental input impedance (Zin = vin/iin) for
minimum, nominal, and maximum input voltage at full rated power.
Figure 23: High frequency conducted emissions of standalone MQFL270-05S, 5Vout module at 120W output, as measured with Method
CE102. Limit line shown is the ‘Basic Curve’ for all applications with a
270V source.
Figure 24: High frequency conducted emissions of MQFL-270-05S,
5Vout module at 120W output with MQME-270-P filter, as measured with
Method CE102. Limit line shown is the ‘Basic Curve’ for all applications
with a 270V source.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 8
MQFL-270-12S
Output: 12V
Current: 10A
Application Section
BASIC OPERATION AND FEATURES
The MQFL DC-DC converter uses a two-stage power conversion
topology. The first, or regulation, stage is a buck-converter that
keeps the output voltage constant over variations in line, load,
and temperature. The second, or isolation, stage uses transformers to provide the functions of input/output isolation and
voltage transformation to achieve the output voltage required.
Both the regulation and the isolation stages switch at a fixed
frequency for predictable EMI performance. The isolation stage
switches at one half the frequency of the regulation stage, but
due to the push-pull nature of this stage it creates a ripple at
double its switching frequency. As a result, both the input and
the output of the converter have a fundamental ripple frequency
of about 550 kHz in the free-running mode.
Rectification of the isolation stage’s output is accomplished with
synchronous rectifiers. These devices, which are MOSFETs with a
very low resistance, dissipate far less energy than would Schottky
diodes. This is the primary reason why the MQFL converters have
such high efficiency, particularly at low output voltages.
Besides improving efficiency, the synchronous rectifiers permit
operation down to zero load current. There is no longer a need
for a minimum load, as is typical for converters that use diodes
for rectification. The synchronous rectifiers actually permit a
negative load current to flow back into the converter’s output
terminals if the load is a source of short or long term energy.
The MQFL converters employ a “back-drive current limit” to
keep this negative output terminal current small.
CONTROL FEATURES
ENABLE: The MQFL converter has two enable pins. Both must
have a logic high level for the converter to be enabled. A logic
low on either pin will inhibit the converter.
The ENA1 pin (pin 4) is referenced with respect to the converter’s input return (pin 2). The ENA2 pin (pin 12) is referenced
with respect to the converter’s output return (pin 8). This permits the converter to be inhibited from either the input or the
output side.
Regardless of which pin is used to inhibit the converter, the
regulation and the isolation stages are turned off. However,
when the converter is inhibited through the ENA1 pin, the bias
supply is also turned off, whereas this supply remains on when
the converter is inhibited through the ENA2 pin. A higher input
standby current therefore results in the latter case.
Both enable pins are internally pulled high so that an open connection on both pins will enable the converter. Figure A shows
the equivalent circuit looking into either enable pins. It is TTL
compatible.
5.0V
PIN 4
(OR PIN 12)
The MQFL converter’s control circuit does not implement an output over-voltage limit or an over-temperature shutdown.
The following sections describe the use and operation of additional control features provided by the MQFL converter.
Product# MQFL-270-12S
Phone 1-888-567-9596
68K
ENABLE
TO ENABLE
CIRCUITRY
250K
2N3904
There is a control circuit on both the input and output sides
of the MQFL converter that determines the conduction state
of the power switches. These circuits communicate with each
other across the isolation barrier through a magnetically coupled
device. No opto-isolators are used. A separate bias supply provides power to both the input and output control circuits.
An input under-voltage lockout feature with hysteresis is provided, as well as an input over-voltage shutdown. There is also
an output current limit that is nearly constant as the load impedance decreases to a short circuit (i.e., there is no fold-back or
fold-forward characteristic to the output current under this condition). When a load fault is removed, the output voltage rises
exponentially to its nominal value without an overshoot.
1N4148
125K
PIN 2
(OR PIN 8)
IN RTN
Figure A: Circuit diagram shown for reference only, actual circuit
components may differ from values shown for equivalent circuit.
SHUT DOWN: The MQFL converter will shut down in response
to following conditions:
-
ENA1 input low
ENA2 input low
VIN input below under-voltage lockout threshold
VIN input above over-voltage shutdown threshold
Persistent current limit event lasting more than 1 second
Following a shutdown from a disable event or an input voltage
fault, there is a startup inhibit delay which will prevent the
converter from restarting for approximately 300 ms. After the
300 ms delay elapses, if the enable inputs are high and the input
voltage is within the operating range, the converter will restart.
If the VIN input is brought down to nearly 0 V and back into
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 9
MQFL-270-12S
Output: 12V
Current: 10A
Application Section
the operating range, there is no startup inhibit, and the output
voltage will rise according to the “Turn-On Delay, Rising Vin”
specification.
Refer to the following Current Limit section for details regarding
persistent current limit behavior.
REMOTE SENSE: The purpose of the remote sense pins is
to correct for the voltage drop along the conductors that connect the converter’s output to the load. To achieve this goal, a
separate conductor should be used to connect the +SENSE pin
(pin 10) directly to the positive terminal of the load, as shown
in the connection diagram. Similarly, the –SENSE pin (pin 9)
should be connected through a separate conductor to the return
terminal of the load.
NOTE: Even if remote sensing of the load voltage is not desired,
the +SENSE and the -SENSE pins must be connected to +Vout
(pin 7) and OUTPUT RETURN (pin 8), respectively, to get proper
regulation of the converter’s output. If they are left open, the
converter will have an output voltage that is approximately 200
mV higher than its specified value. If only the +SENSE pin is left
open, the output voltage will be approximately 25 mV too high.
The MQFL converter also has a SYNC OUT pin (pin 5). This output can be used to drive the SYNC IN pins of as many as ten (10)
other MQFL converters. The pulse train coming out of SYNC
OUT has a duty cycle of 50 % and a frequency that matches the
switching frequency of the converter with which it is associated.
This frequency is either the free-running frequency if there is no
synchronization signal at the SYNC IN pin, or the synchronization
frequency if there is.
The SYNC OUT signal is available only when the DC input voltage is above approximately 125 V and when the converter is not
inhibited through the ENA1 pin. An inhibit through the ENA2 pin
will not turn the SYNC OUT signal off.
NOTE: An MQFL converter that has its SYNC IN pin driven by
the SYNC OUT pin of a second MQFL converter will have its start
of its switching cycle delayed approximately 180 degrees relative
to that of the second converter.
Figure B shows the equivalent circuit looking into the SYNC IN pin.
Figure C shows the equivalent circuit looking into the SYNC OUT pin.
5V
Inside the converter, +SENSE is connected to +Vout with a 100
W resistor and –SENSE is connected to OUTPUT RETURN with a
10 W resistor.
It is also important to note that when remote sense is used, the
voltage across the converter’s output terminals (pins 7 and 8)
will be higher than the converter’s nominal output voltage due
to resistive drops along the connecting wires. This higher voltage at the terminals produces a greater voltage stress on the
converter’s internal components and may cause the converter to
fail to deliver the desired output voltage at the low end of the
input voltage range at the higher end of the load current and
temperature range. Please consult the factory for details.
5K
PIN 6
PIN 2
SYNC IN
TO SYNC
CIRCUITRY
5K
IN RTN
Figure B: Equivalent circuit looking into the SYNC IN pin with
respect to the IN RTN (input return) pin.
SYNCHRONIZATION: The MQFL converter’s switching frequency can be synchronized to an external frequency source
that is in the 500 kHz to 700 kHz range. A pulse train at the
desired frequency should be applied to the SYNC IN pin (pin
6) with respect to the INPUT RETURN (pin 2). This pulse train
should have a duty cycle in the 20 % to 80 % range. Its low
value should be below 0.8 V to be guaranteed to be interpreted
as a logic low, and its high value should be above 2.0 V to be
guaranteed to be interpreted as a logic high. The transition time
between the two states should be less than 300 ns.
FROM SYNC
CIRCUITRY
If the MQFL converter is not to be synchronized, the SYNC IN pin
should be left open circuit. The converter will then operate in
its free-running mode at a frequency of approximately 550 kHz.
Figure C: Equivalent circuit looking into SYNC OUT pin with
respect to the IN RTN (input return) pin.
5V
5K
SYNC OUT
IN RTN
OPEN COLLECTOR
OUTPUT
PIN 5
PIN 2
If, due to a fault, the SYNC IN pin is held in either a logic low or
logic high state continuously, the MQFL converter will revert to
its free-running frequency.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 10
MQFL-270-12S
Output: 12V
Current: 10A
Application Section
Since the SHARE pin is monitored with respect to the OUTPUT
RETURN (pin 8) by each converter, it is important to connect
all of the converters’ OUTPUT RETURN pins together through a
low DC and AC impedance. When this is done correctly, the
converters will deliver their appropriate fraction of the total load
current to within +/- 10 % at full rated load.
Whether or not converters are paralleled, the voltage at the
SHARE pin could be used to monitor the approximate average
current delivered by the converter(s). A nominal voltage of 1.0
V represents zero current and a nominal voltage of 2.2 V represents the maximum rated total current, with a linear relationship
in between. The internal source resistance of a converter’s
SHARE pin signal is 2.5 kW.
During an input voltage fault or primary disable event, the
SHARE pin outputs a power failure warning pulse. The SHARE
pin will go to 3 V for approximately 14 ms as the output voltage
falls. During a current limit auto-restart event, the SHARE pin
outputs a startup synchronization pulse. The SHARE pin will
go to 5 V for approximately 2 ms before the converter restarts.
NOTE: Converters operating from separate input filters with
reverse polarity protection (such as the MQME-270-R filter)
with their outputs connected in parallel may exhibit auto-restart
operation at light loads. Consult factory for details.
OUTPUT VOLTAGE TRIM: If desired, it is possible to increase
the MQFL converter’s output voltage above its nominal value.
To do this, use the +SENSE pin (pin 10) for this trim function
instead of for its normal remote sense function, as shown in
1
2
3
270Vdc
4
+
–
5
open
means
on
6
100,000
Trim Resistance (ohms)
CURRENT SHARE: When several MQFL converters are placed
in parallel to achieve either a higher total load power or N+1
redundancy, their SHARE pins (pin 11) should be connected
together. The voltage on this common SHARE node represents
the average current delivered by all of the paralleled converters.
Each converter monitors this average value and adjusts itself
so that its output current closely matches that of the average.
10,000
1,000
100
0.0
0.2
0.4
0.6
0.8
Increase in Vout (V)
1.0
1.2
1.4
Figure E: Output Voltage Trim Graph
Figure D. In this case, a resistor connects the +SENSE pin to
the –SENSE pin (which should still be connected to the output
return, either remotely or locally). The value of the trim resistor
should be chosen according to the following equation or from
Figure E:
Rtrim = 100 x
Vnom
Vout - Vnom - 0.025
where:
Vnom = the converter’s nominal output voltage,
Vout = the desired output voltage (greater than Vnom), and
Rtrim is in Ohms.
As the output voltage is trimmed up, it produces a greater
voltage stress on the converter’s internal components and may
cause the converter to fail to deliver the desired output voltage
at the low end of the input voltage range at the higher end of
the load current and temperature range. Please consult the
factory for details.
+VIN
ENA 2
IN RTN
SHARE
CASE
+ SNS
ENA 1
– SNS
SYNC OUT
SYNC IN
OUT RTN
+VOUT
12
11
10
9
Rtrim
–
8
7
Load
+
Figure D: Typical connection for output voltage trimming.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 11
MQFL-270-12S
Output: 12V
Current: 10A
Application Section
INPUT UNDER-VOLTAGE LOCKOUT: The MQFL converter
has an under-voltage lockout feature that ensures the converter
will be off if the input voltage is too low. The threshold of
input voltage at which the converter will turn on is higher that
the threshold at which it will turn off. In addition, the MQFL
converter will not respond to a state of the input voltage unless
it has remained in that state for more than about 200 µs. This
hysteresis and the delay ensure proper operation when the
source impedance is high or in a noisy environment.
INPUT OVER-VOLTAGE SHUTDOWN: The MQFL converter
also has an over-voltage feature that ensures the converter will
be off if the input voltage is too high. It also has a hysteresis
and time delay to ensure proper operation.
CURRENT LIMIT: The converter will reduce its output voltage in response to an overload condition. If the output voltage
drops to below approximately 50 % of the nominal setpoint for
longer than 1 second, the auto-restart feature will engage. The
auto-restart feature will stop the converter from delivering load
current, in order to protect the converter and the load from thermal damage. After four seconds have elapsed, the converter will
automatically restart.
In a system with multiple converters configured for load sharing
using the SHARE pin, if the auto-restart feature engages,
the converters will synchronize their restart using signals
communicated on the SHARE pin.
BACK-DRIVE CURRENT LIMIT: Converters that use MOSFETs
as synchronous rectifiers are capable of drawing a negative current from the load if the load is a source of short- or long-term
energy. This negative current is referred to as a “back-drive current”.
Conditions where back-drive current might occur include
paralleled converters that do not employ current sharing, or
where the current share feature does not adequately ensure
sharing during the startup or shutdown transitions. It can also
occur when converters having different output voltages are
connected together through either explicit or parasitic diodes
that, while normally off, become conductive during startup or
shutdown. Finally, some loads, such as motors, can return
energy to their power rail. Even a load capacitor is a source of
back-drive energy for some period of time during a shutdown
transient.
THERMAL CONSIDERATIONS: The suggested Power Derating
Curves for this converter as a function of the case temperature
and the maximum desired power MOSFET junction temperature
on the figures page. All other components within the converter
are cooler than its hottest MOSFET, which at full power is no
more than 20 ºC higher than the case temperature directly
below this MOSFET. The Mil-HDBK-1547A component derating
guideline calls for a maximum component temperature of 105
ºC. The power derating figure; therefore has one power derating
curve that ensures this limit is maintained. It has been SynQor’s
extensive experience that reliable long-term converter operation
can be achieved with a maximum component temperature of
125 ºC. In extreme cases, a maximum temperature of 145 ºC is
permissible, but not recommended for long-term operation where
high reliability is required. Derating curves for these higher
temperature limits are also included in Figure 5. The maximum
case temperature at which the converter should be operated is
135 ºC.
When the converter is mounted on a metal plate, the plate
will help to make the converter’s case bottom a uniform temperature. How well it does so depends on the thickness of the
plate and on the thermal conductance of the interface layer
(e.g. thermal grease, thermal pad, etc.) between the case and
the plate. Unless this is done very well, it is important not to
mistake the plate’s temperature for the maximum case temperature. It is easy for them to be as much as 5-10 ºC different at
full power and at high temperatures. It is suggested that a thermocouple be attached directly to the converter’s case through a
small hole in the plate when investigating how hot the converter
is getting. Care must also be made to ensure that there is not
a large thermal resistance between the thermocouple and the
case due to whatever adhesive might be used to hold the thermocouple in place.
INPUT SYSTEM INSTABILITY: This condition can occur
because any DC-DC converter appears incrementally as a
negative resistance load. A detailed application note titled
“Input System Instability” is available on the SynQor website
which provides an understanding of why this instability arises,
and shows the preferred solution for correcting it.
To avoid any problems that might arise due to back-drive
current, the MQFL converters limit the negative current that the
converter can draw from its output terminals. The threshold
for this back-drive current limit is placed sufficiently below zero
so that the converter may operate properly down to zero load,
but its absolute value (see the Electrical Characteristics page) is
small compared to the converter’s rated output current.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 12
MQFL-270-12S
Output: 12V
Current: 10A
Stress Screening
CONSTRUCTION AND ENVIRONMENTAL STRESS SCREENING OPTIONS
Consistent with
MIL-STD-883F
Screening
C-Grade
ES-Grade
from
( specified
0 °C to +70 °C )
Element Evaluation
HB-Grade
from
from
( -45specified
( -55specified
°C to +100 °C )
°C to +125 °C )
No
Yes
Yes
Yes
Yes
Internal Visual
*
Yes
Temperature Cycle
Method 1010
No
Constant Acceleration
Method 2001
(Y1 Direction)
No
500g
Condition A
(5000g)
Burn-in
Method 1015
24 Hrs @ +125 °C
96 Hrs @ +125 °C
160 Hrs @ +125 °C
Final Electrical Test
Method 5005 (Group A)
+25 °C
-45, +25, +100 °C
-55, +25, +125 °C
Full QorSeal
Full QorSeal
Yes
Yes
QorSeal
QorSeal
Mechanical Seal,
Thermal, and
Coating Process
External Visual
2009
*
Construction Process
Condition B
Condition C
(-55 °C to +125 °C) (-65 °C to +150 °C)
* Per IPC-A-610 Class 3
MilQor® Hi-Rel converters and filters are offered in three variations of environmental stress screening options. All ES-Grade and HB-Grade MilQor
Hi-Rel converters use SynQor’s proprietary QorSeal® Hi-Rel assembly process that includes a Parylene-C coating of the circuit, a high performance
thermal compound filler, and a nickel barrier gold plated aluminum case. Each successively higher grade has more stringent mechanical and
electrical testing, as well as a longer burn-in cycle. The ES- and HB-Grades are also constructed of components that have been procured through an
element evaluation process that pre-qualifies each new batch of devices.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 13
MQFL-270-12S
Output: 12V
Current: 10A
Technical Specifications
MIL-STD-810F Qualification Testing
MIL-STD-810F Test
Fungus
Method
Description
508.5
Table 508.5-I
500.4 - Procedure I
Storage: 70,000 ft / 2 hr duration
500.4 - Procedure II
Operating: 70,000 ft / 2 hr duration; Ambient Temperature
Rapid Decompression
500.4 - Procedure III
Storage: 8,000 ft to 40,000 ft
Acceleration
513.5 - Procedure II
Operating: 15 g
Salt Fog
509.4
Storage
501.4 - Procedure I
Storage: 135°C / 3 hrs
501.4 - Procedure II
Operating: 100°C / 3 hrs
502.4 - Procedure I
Storage: -65°C / 4 hrs
502.4 - Procedure II
Operating: -55°C / 3 hrs
Altitude
High Temperature
Low Temperature
Temperature Shock
503.4 - Procedure I - C Storage: -65°C to 135°C; 12 cycles
Rain
506.4 - Procedure I
Wind Blown Rain
Immersion
512.4 - Procedure I
Non-Operating
Humidity
507.4 - Procedure II
Random Vibration
514.5 - Procedure I
10 - 2000 Hz, PSD level of 1.5 g2/Hz (54.6 grms), duration = 1 hr/axis
516.5 - Procedure I
20 g peak, 11 ms, Functional Shock (Operating no load) (saw tooth)
516.5 - Procedure VI
Bench Handling Shock
Shock
Sinusoidal vibration
Sand and Dust
Product# MQFL-270-12S
514.5 - Category 14
Aggravated cycle @ 95% RH (Figure 507.5-7 aggravated temp humidity cycle, 15 cycles)
Rotary wing aircraft - helicopter, 4 hrs/axis, 20 g (sine sweep from
10 - 500 Hz)
510.4 - Procedure I
Blowing Dust
510.4 - Procedure II
Blowing Sand
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 14
MQFL-270-12S
Output: 12V
Current: 10A
Technical Specifications
First Article Testing consistent with MIL-STD-883F
MIL-STD-883F Test
Method
Description
Electrical Tests
5005
Physical Dimensions test
2016
Resistance to Solvents test
2015.13
Solderability test
2003.8
Lead Integrity test
2004.5
Salt Atmosphere test
1009.8
Adhesion of Lead Finish test
2025.4
Altitude Operation test
1001
Condition “C”
ESD Sensitivity
3015.7
Class 2
Stabilization Bake test
1008.2
Condition “C”
Vibration Fatigue test
2005.2
Condition “A”
Random Vibration test
2026
Condition “II K”
Condition “A”
Sequential Test Group #1
Life Test – Steady State test
1005.8
Life Test – Intermittent Duty test
1006
Sequential Test Group #2
Temperature Cycle test
1010.8
Condition “C”
Constant Acceleration test
2001.2
Condition “A”
Thermal Shock test
1011.9
Condition “B”
Temperature Cycle test
1010.8
Condition “C”
Moisture Resistance test
1004.7
With Sub cycle
Mechanical Shock test
2002.4
Condition “B”
Variable Frequency Vibration test
2007.3
Condition “A”
Sequential Test Group #3
Sequential Test Group #4
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 15
MQFL-270-12S
Output: 12V
Current: 10A
Mechanical Diagrams
1
2
3
4
5
6
SEE NOTE 7
+VIN
IN RTN
SHARE
MQFL-270-12S-X-ES
CASE
+SNS
DC-DC CONVERTER
270Vin 12Vout @ 10A
ENA 1
-SNS
SYNC OUT
SYNC IN
12
11
10
9
8
7
ENA 2
MADE IN USA
OUT RTN
S/N 0000000 D/C 3205-301 CAGE 1WX10
+VOUT
0.250 [6.35]
1.50 [38.1]
0.040 [1.02]
PIN
2.50 [63.50]
2.760 [70.10]
3.00 [76.2]
0.22 [5.6]
0.228 [5.79]
0.390 [9.91]
SEE NOTE 7
6
+VIN
ENA 2
IN RTN
SHARE
MQFL-270-12S-U-ES
CASE
+SNS
DC-DC CONVERTER
270Vin 12Vout @ 10A
ENA 1
SYNC OUT
SYNC IN
0.050 [1.27]
0.128 [3.25]
2.96 [75.2]
1
2
3
4
5
0.200 [5.08]
TYP. NON-CUM.
1.260
[32.00]
-SNS
MADE IN USA
S/N 0000000 D/C 3211-301 CAGE 1WX10
OUT RTN
+VOUT
12
11
10
9
8
7
2.50 [63.5]
2.760 [70.10]
3.00 [76.2]
Case X
0.250 [6.35]
0.200 [5.08]
TYP.
NON-CUM.
1.50 [38.1]
1.260
[32.00]
0.040
[1.02]
PIN
0.050 [1.27]
0.42
[10.7]
0.128 [3.25]
0.22 [5.6]
2.80 [71.1]
0.390 [9.91]
PIN DESIGNATIONS
NOTES
1)
2)
3)
4)
5)
6)
7)
8)
Pins 0.040’’ (1.02mm) diameter
Pin Material: Copper Alloy
Finish: Gold over Nickel plating, followed by Sn/Pb solder dip
All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
Weight: 2.8 oz (78.5 g) typical
Workmanship: Meets or exceeds IPC-A-610 Class III
Print Labeling on Top Surface per Product Label Format Drawing
Pin 1 identification hole, not intended for mounting (case X and U)
Baseplate flatness tolerance is 0.004” (.10mm) TIR for surface.
Product# MQFL-270-12S
Case U
Phone 1-888-567-9596
www.SynQor.com
Pin # Function
1
2
3
4
5
6
Pin # Function
Positive input
Input return
Case
Enable 1
Sync output
Sync input
Doc.# 005-0005076 Rev. E
7
8
9
10
11
12
Positive output
Output return
- Sense
+ Sense
Share
Enable 2
01/04/16
Page 16
MQFL-270-12S
Output: 12V
Current: 10A
Mechanical Diagrams
0.300 [7.62]
0.140 [3.56]
1.150 [29.21]
0.250 [6.35]
TYP
1
2
3
4
5
6
+VIN
ENA 2
IN RTN
SHARE
MQFL-270-12S-Y-ES
CASE
-SNS
SYNC OUT
SYNC IN
+SNS
DC-DC CONVERTER
270Vin 12Vout @ 10A
ENA 1
MADE IN USA
S/N 0000000 D/C 3211-301 CAGE 1WX10
OUT RTN
+VOUT
1.750 [44.45]
12
2.000
11
[50.80]
10
1.50
9 [38.1]
8
1.750
7
[44.45]
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
0.050 [1.27]
0.22 [5.6]
0.375 [9.52]
2.50 [63.5]
2.96 [75.2]
0.228 [5.79]
0.390 [9.91]
Case Y
Case Z
(variant of Y)
0.250 [6.35]
Case W
(variant of Y)
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
0.040 [1.02]
PIN
0.22 [5.6]
0.050 [1.27]
0.42 [10.7]
0.36 [9.14]
0.050 [1.27]
0.22 [5.6]
2.80 [71.1]
0.525 [13.33]
0.390
[9.91]
0.525 [13.33]
0.390
[9.91]
2.80 [71.1]
PIN DESIGNATIONS
NOTES
1)
2)
3)
4)
5)
6)
7)
8)
Pins 0.040’’ (1.02mm) diameter
Pin Material: Copper Alloy
Finish: Gold over Nickel plating, followed by Sn/Pb solder dip
All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
Weight: 2.8 oz (78.5 g) typical
Workmanship: Meets or exceeds IPC-A-610 Class III
Print Labeling on Top Surface per Product Label Format Drawing
Pin 1 identification hole, not intended for mounting (case X and U)
Baseplate flatness tolerance is 0.004” (.10mm) TIR for surface.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Pin # Function
1
2
3
4
5
6
Pin # Function
Positive input
Input return
Case
Enable 1
Sync output
Sync input
Doc.# 005-0005076 Rev. E
7
8
9
10
11
12
Positive output
Output return
- Sense
+ Sense
Share
Enable 2
01/04/16
Page 17
MQFL-270-12S
Output: 12V
Current: 10A
Ordering Information
MilQor Converter FAMILY MATRIX
The tables below show the array of MilQor converters available. When ordering SynQor converters, please ensure that
you use the complete part number according to the table in the last page. Contact the factory for other requirements.
Single Output
Full Size
MQFL-28
16-40Vin Cont.
16-50Vin 1s Trans.*
Dual Output †
1.5V
(1R5S)
1.8V
(1R8S)
2.5V
(2R5S)
3.3V
(3R3S)
5V
(05S)
6V
(06S)
7.5V
(7R5S)
9V
(09S)
12V
(12S)
15V
(15S)
28V
(28S)
5V
(05D)
12V
(12D)
15V
(15D)
40A
40A
40A
30A
24A
20A
16A
13A
10A
8A
4A
24A
Total
10A
Total
8A
Total
40A
40A
40A
30A
24A
20A
16A
13A
10A
8A
4A
24A
Total
10A
Total
8A
Total
40A
40A
40A
30A
20A
17A
13A
11A
8A
6.5A
3.3A
40A
40A
40A
30A
20A
17A
13A
11A
8A
6.5A
3.3A
40A
40A
40A
30A
24A
20A
16A
13A
10A
8A
4A
24A
Total
10A
Total
8A
Total
40A
40A
30A
22A
15A
12A
10A
8A
6A
5A
2.7A
15A
Total
6A
Total
5A
Total
1.5V
(1R5S)
1.8V
(1R8S)
2.5V
(2R5S)
3.3V
(3R3S)
5V
(05S)
6V
(06S)
7.5V
(7R5S)
9V
(09S)
12V
(12S)
15V
(15S)
28V
(28S)
5V
(05D)
12V
(12D)
15V
(15D)
20A
20A
20A
15A
10A
8A
6.6A
5.5A
4A
3.3A
1.8A
10A
Total
4A
Total
3.3A
Total
20A
20A
20A
15A
10A
8A
6.6A
5.5A
4A
3.3A
1.8A
10A
Total
4A
Total
3.3A
Total
10A
10A
10A
7.5A
5A
4A
3.3A
2.75A
2A
1.65A
0.9A
5A
Total
2A
Total
1.65A
Total
10A
10A
10A
7.5A
5A
4A
3.3A
2.75A
2A
1.65A
0.9A
5A
Total
2A
Total
1.65A
Total
Absolute Max Vin = 60V
MQFL-28E
16-70Vin Cont.
16-80Vin 1s Trans.*
Absolute Max Vin =100V
MQFL-28V
16-40Vin Cont.
5.5-50Vin 1s Trans.*
Absolute Max Vin = 60V
MQFL-28VE
16-70Vin Cont.
5.5-80Vin 1s Trans.*
Absolute Max Vin = 100V
MQFL-270
155-400Vin Cont.
155-475Vin 1s Trans.*
Absolute Max Vin = 550V
MQFL-270L
65-350Vin Cont.
65-475Vin 1s Trans.*
Absolute Max Vin = 550V
Single Output
Half Size
MQHL-28
16-40Vin Cont.
16-50Vin 1s Trans.*
Dual Output †
Absolute Max Vin = 60V
MQHL-28E
16-70Vin Cont.
16-80Vin 1s Trans.*
Absolute Max Vin =100V
MQHR-28
16-40Vin Cont.
16-50Vin 1s Trans.*
Absolute Max Vin = 60V
MQHR-28E
16-70Vin Cont.
16-80Vin 1s Trans.*
Absolute Max Vin = 100V
Check with factory for availability.
†80% of total output current available on any one output.
*Converters may be operated at the highest transient input voltage, but some component electrical and thermal stresses would be beyond MILHDBK-1547A guidelines.
Product# MQFL-270-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 18
MQFL-270-12S
Output: 12V
Current: 10A
Ordering Information
PART NUMBERING SYSTEM
The part numbering system for SynQor’s MilQor DC-DC converters follows the format shown in the table below.
Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options.
Example:
Input
Voltage
Range
Model
Name
28
28E
28V
28VE
MQFL
MQHL
MQHR
270
270L
MQFL-270-12S-Y-ES
Output Voltage(s)
Single
Output
Dual
Output
1R5S
1R8S
2R5S
3R3S
05S
06S
7R5S
09S
12S
15S
28S
05D
12D
15D
Package Outline/
Pin Configuration
Screening
Grade
U
X
Y
W
Z
C
ES
HB
APPLICATION NOTES
A variety of application notes and technical white papers can be downloaded in pdf format from the SynQor website.
Contact SynQor for further information and to order:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product# MQFL-270-12S
978-849-0600
1-888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
PATENTS
SynQor holds numerous U.S. patents, one or more of which apply to most of its power converter
products. Any that apply to the product(s) listed in this document are identified by markings on
the product(s) or on internal components of the product(s) in accordance with U.S. patent laws.
SynQor’s patents include the following:
5,999,417
6,222,742
6,545,890
6,594,159 6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
8,493,751 8,644,027
9,143,042
Warranty
SynQor offers a two (2) year limited warranty. Complete warranty information
is listed on our website or is available upon request from SynQor.
www.SynQor.com
Doc.# 005-0005076 Rev. E
01/04/16
Page 19