C8051F53x/52x C8051F530A D EVELOPMENT K I T U SER ’ S G UIDE 1. Relevant Devices The C8051F530 Development Kit is intended as a development platform for microcontrollers in the C8051F53x/ 52x MCU family. Code developed on the C8051F530 can be easily ported to the other members of this MCU family. 2. Kit Contents The C8051F530 Development Kit contains the following items: C8051F530A Target Board C8051Fxxx Development Kit Quick-Start Guide AC to DC Power Adapter USB Debug Adapter (USB to Debug Interface) USB Cable The development kit target board contains two C8051F530 microcontrollers that can communicate through an LIN network. One of the C8051F530 (U2) can also be connected to a CP2102 USB to UART bridge and directly connected to two analog signals and a Voltage Reference Signal Input. 3. Hardware Setup Using a USB Debug Adapter The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown in Figure 1. 1. Connect the USB Debug Adapter to one of the DEBUG connectors on the target board (HDR1 or HDR2) with the 10-pin ribbon cable. The recommended connection is to the HDR2 (connected to U2) as this microcontroller can be connected to the CP2102 USB to UART bridge. 2. Verify that shorting blocks are installed on J13 and J14 to supply power to the target devices. 3. Connect one end of the USB cable to the USB connector on the USB Debug Adapter. 4. Connect the other end of the USB cable to a USB Port on the PC. 5. Connect the ac/dc power adapter to power jack P5 on the target board. Target Board DEBUG_B P5 Reset_A P1.4_B U1 HDR3 D1 J14 C8051F530A TB “B” Side T1 PWR U2 J13 T2 U3 P1 DEBUG_A P1.6_B HDR2 P1.7_B J4 J3 J5 P0.0_B Run Stop Silicon Laboratories USB DEBUG ADAPTER Power USB Cable SILICON LABORATORIES “A” Side P1.4_A 4 USB Debug Adapter RDH J8 D2 J6 PC HDR1 Reset_B AC/DC Adapter Figure 1. Hardware Setup using a USB Debug Adapter Rev. 0.4 11/14 Copyright © 2014 by Silicon Laboratories C8051F53x/52x C8051F53x/52x Notes: 1. Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter. 2. Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power can damage the device and/or the USB Debug Adapter. 4. Software Setup Simplicity Studio greatly reduces development time and complexity with Silicon Labs EFM32 and 8051 MCU products by providing a high-powered IDE, tools for hardware configuration, and links to helpful resources, all in one place. Once Simplicity Studio is installed, the application itself can be used to install additional software and documentation components to aid in the development and evaluation process. Figure 2. Simplicity Studio The following Simplicity Studio components are required for the C8051F530 Development Kit: 8051 Products Part Support Developer Platform Download and install Simplicity Studio from www.silabs.com/8bit-software or www.silabs.com/simplicity-studio. Once installed, run Simplicity Studio by selecting StartSilicon LabsSimplicity StudioSimplicity Studio from the start menu or clicking the Simplicity Studio shortcut on the desktop. Follow the instructions to install the software and click Simplicity IDE to launch the IDE. Simplicity The first time the project creation wizard runs, the Setup Environment wizard will guide the user through the process of configuring the build tools and SDK selection. 2 Rev. 0.4 C8051F53x/52x In the Part Selection step of the wizard, select from the list of installed parts only the parts to be used during development. Choosing parts and families in this step affects the displayed or filtered parts in the later device selection menus. Choose the C8051F53x/52x family by checking the C8051F53x/52x check box. Modify the part selection at any time by accessing the Part Management dialog from the WindowPreferencesSimplicity StudioPart Management menu item. Simplicity Studio can detect if certain toolchains are not activated. If the Licensing Helper is displayed after completing the Setup Environment wizard, follow the instructions to activate the toolchain. 4.1. Running Blinky Each project has its own source files, target configuration, SDK configuration, and build configurations such as the Debug and Release build configurations. The IDE can be used to manage multiple projects in a collection called a workspace. Workspace settings are applied globally to all projects within the workspace. This can include settings, such as key bindings, window preferences, and code style and formatting options. Project actions, such as build and debug, are context-sensitive. For example, the user must select a project in the Project Explorer view in order to build that project. To create a project based on the Blinky example, perform the following steps: 1. Click the Software Examples tile from the Simplicity Studio home screen. 2. In the Kit drop-down, select C8051F530A Development Kit; in the Part drop-down, select C8051F530, and in the SDK drop-down, select the desired SDK. Click Next. 3. Select Example, and click Next. 4. Under C8051F530A Development Kit, select F52x-53x Blinky; click Next, and click Finish. 5. Click on the project in the Project Explorer, and click Build (the hammer icon in the top bar). Alternatively, go to ProjectBuild Project. 6. Click Debug to download the project to the hardware and start a debug session. 7. Press the Resume button to start the code running. The LED should blink. 8. Press the Suspend button to stop the code. 9. Press the Reset the device button to reset the target MCU. 10. Press the Disconnect button to return to the development perspective. 4.2. Simplicity Studio Help Simplicity Studio includes detailed help information and device documentation within the tool. The help contains descriptions for each dialog window. To view the documentation for a dialog, click the question mark icon in the window: This will open a pane specific to the dialog with additional details. The documentation within the tool can also be viewed by going to HelpHelp Contents or HelpSearch. Rev. 0.4 3 C8051F53x/52x 4.3. CP210x USB to UART VCP Driver Installation The Target Board includes a Silicon Labs CP210x USB-to-UART Bridge Controller. Device drivers for the CP210x need to be installed before the PC software can communicate with the MCU through the UART interface. 1. After opening Simplicity Studio for the first time, a dialog will prompt to install the CP210x drivers. Click Yes. The drivers can also be installed at any time by going to HelpInstall DriversCP210x VCP USB Drivers. 2. Accept the license agreement and follow the steps to install the driver on the system. The installer will let you know when your system is up to date. The driver files included in this installation have been certified by Microsoft. 3. To complete the installation process, connect the included USB cable between the host computer and the USB connector (P4) on the Target Board. Windows will automatically finish the driver installation. Information windows will pop up from the taskbar to show the installation progress. 4. If necessary, the driver files can be uninstalled by selecting Windows Driver Package—Silicon Laboratories... option in the Programs and Features window. 4.4. Configuration Wizard 2 The Configuration Wizard 2 is a code generation tool for all of the Silicon Laboratories devices. Code is generated through the use of dialog boxes for each of the device's peripherals. Figure 3. Configuration Wizard 2 Utility The Configuration Wizard 2 utility helps accelerate development by automatically generating initialization source code to configure and enable the on-chip resources needed by most design projects. In just a few steps, the wizard creates complete startup code for a specific Silicon Laboratories MCU. The program is configurable to provide the output in C or assembly language. For more information, refer to the Configuration Wizard documentation. Documentation and software is available on the kit CD and from the downloads web page: www.silabs.com/ mcudownloads. 4 Rev. 0.4 C8051F53x/52x 5. Target Board The C8051F52xA-53xA Development Kit includes a target board with two C8051F530A devices preinstalled for evaluation and preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping using the target board. Refer to Figure 4 for the locations of the various I/O connectors. Table 1. Target Board Part Summary Part P5 Description Power connector (Accepts input from 7 to 15 VDC unregulated power adapter.) PWR Red Power-on LED (D3) TB1 LIN connector U5 5 V Voltage Regulator A Side J2 28-pin Expansion I/O connector for U2 HDR2 Debug connector for Debug Adapter Interface P1.3_A Green LED (D2) Reset_A Reset button P1.4_A Push button R32 J6, J8 J13 J11, J12 Potentiometer for P1.2_A Connects R32 (potentiometer) to U2 and +5 V Connects power to U2 Connects external crystal to U2 pins P0.7_A and P1.0_A J3 Connects analog channel 1 to U2 P1.6_A J4 Connects analog channel 2 to U2 P1.7_A J5 Connects VREFIN to U2 P0.0_A TB2 HDR4 Analog input connector Connector block for serial port connection, Green LED, and push-button U3 Silicon Laboratories CP2102 USB-to-UART Bridge P1 USB connector to serial interface (CP2102) USB ACTIVE Red USB Active LED (D4) (CP2102) T2 LIN transceiver U2 C8051F530A “A” Side Rev. 0.4 5 C8051F53x/52x Table 1. Target Board Part Summary Part Description B Side J1 26-pin Expansion I/O connector for U1 HDR1 Debug connector for Debug Adapter Interface P1.3_B Green LED (D1) Reset_B Reset button P1.4_B Push button J14 Connects power to U1 J9, J10 Connects external crystal to U1 pins P0.7_B and P1.0_B HDR3 Green LED and push-button connector block T1 LIN transceiver U1 C8051F530A “B” Side 5.1. Target Board Shorting Blocks: Factory Defaults The C8051F530A target board comes from the factory with preinstalled shorting blocks on many headers. Figure 4 shows the positions of the factory default shorting blocks. P1.4_A R32 J8 GND CH2 CH1 VRefin J3 P1 T2 J6 J13 U3 J12 J11 USB ACTIVE TB1 D4 U2 J2 Pin 1 T1 SILICON LABORATORIES D2 Pin 1 C8051F530A TB U5 PWR D3 P1.3_A HDR4 +12V LIN GND “A” Side J5 P0.0_A J4 P1.6_A DEBUG_A P1.7_A Reset_A HDR2 TB2 Pin 1 “B” Side J14 J10 J9 P5 D1 DEBUG_B HDR1 Reset_B U1 P1.3_B HDR3 Pin 1 J1 P1.4_B Pin 1 Pin 1 Figure 4. C8051F530A Target Board 6 Rev. 0.4 C8051F53x/52x 5.2. System Clock Sources The C8051F530A device installed on the target board features a calibrated programmable internal oscillator that is enabled as the system clock source on reset. After reset, the internal oscillator operates at a frequency of 191.4 kHz (±0.5%) by default but may be configured by software to operate at other frequencies. Therefore, in many applications, an external oscillator is not required. However, if you wish to operate the C8051F530A device at a frequency not available with the internal oscillator, an external crystal may be used. Refer to the C8051F52x/ 52xA/53x/53xA data sheet for more information on configuring the system clock source. The target board is designed to facilitate the installation of external crystals. Install the crystals at the pads marked Y1 or Y2. Install a 10 M resistor at R17 or R22, and install capacitors at C29 and C30 or C34 and C35 using values appropriate for the crystals selected. Headers J9, J10, J11, and J12 connect the external crystal pins to the general purpose I/O headers (J1 and J2). If the external crystal is in use, these headers should not be populated. Refer to the C8051F52x/52xA/53x/53xA data sheet for more information on the use of external oscillators. 5.3. Switches and LEDs Four switches are provided on the target board. Switch RESET_A is connected to the RESET pin of the C8051F530A A-Side (U2). Switch RESET_B is connected to the RESET pin of the C8051F530A B-Side (U1). Pressing RESET_A or RESET_B puts the attached device into its hardware-reset state. Switches P1.4_A and P1.4_B are connected to the C8051F530A parts (U1 and U2) general purpose I/O (GPIO) pins through headers. Pressing P1.4_A or P1.4_B generates a logic low signal on the port pin of the respective microcontroller. Remove the shorting block from the header to disconnect P1.4_A or P1.4_B from the port pins. The port pin signals are also routed to pins on the J1 and J2 I/O connectors. See Table 2 for the port pins and headers corresponding to each switch. Four LEDs are also provided on the target board. The red LED labeled PWR is used to indicate a power connection to the target board. The green LEDs labeled D1 and D2 are connected to the C8051F530A's GPIO pins through headers. Remove the shorting blocks from the headers to disconnect the LEDs from the port pins. The port pin signals are also routed to pins on the J1 and J2 I/O connectors. The red LED labeled USB ACTIVE is used to indicate that the CP2102 USB-to-UART bridge is properly connected to a PC and is ready for communication. See Table 2 for the port pins and headers corresponding to each LED. A potentiometer (R32) is provided on the target board. Header J8 connects the potentiometer to +5 V, and header J6 connects the potentiometer to the P1.2_A pin of the U2 A-Side C8051F530A microcontroller. Table 2. Target Board I/O Descriptions Description I/O Header Reset_A U2-Reset none Reset_B U1-Reset none P1.4_A U2-P1.4 HDR4[3–4] P1.4_B U1-P1.4 HDR3[3–4] Green LED D2 U2-P1.3 HDR4[1–2] Green LED D1 U1-P1.3 HDR3[1–2] Red LED D3 PWR none Red LED D4 USB ACTIVE none Potentiometer R32 U2-P1.2 J6, J8 Rev. 0.4 7 C8051F53x/52x 5.4. Expansion I/O Connectors (J1, J2) The two Expansion I/O connectors J1 (26 pins) and J2 (28 pins) provide access to all signal pins of the C8051F530A devices. Pins for VDD, GND, 5 V, Reset, Vbat, LIN, 3.3 V, and VREFIN are also available. A small through-hole prototyping area is also provided. All I/O signals routed to connectors J1 and J2 are also routed to through-hole connection points between J1 and J2 and the prototyping area (see Figure 4). Each connection point is labeled indicating the signal available at the connection point. Table 3 lists the pin descriptions for J1 and J2. Table 3. Pin Descriptions for J1 and J2 J1 J2 Pin # Description Pin # Description Pin # Description Pin # Description 1 P0.0_B 14 P1.5_B 1 P0.0_A 15 P1.6_A 2 P0.1_B 15 P1.6_B 2 P0.1_A 16 P1.7_A 3 P0.2_B 16 P1.7_B 3 P0.2_A 17 +5V 4 P0.3_B 17 +5V 4 P0.3_A 18 RST/C2CLK_A 5 P0.4_B 18 RST/C2CLK_B 5 P0.4_A 19 VBAT 6 P0.5_B 19 VBAT 6 P0.5_A 20 LIN 7 P0.6_B 20 LIN 7 P0.6_A 21 VREFIN 8 P0.7_B 21 NC 8 P0.7_A 22 VREGOUT_A 9 P1.0_B 22 VREGOUT_B 9 P1.0_A 23 +3.3V 10 P1.1_B 23 NC 10 P1.1_A 24 NC 11 P1.2_B 24 NC 11 P1.2_A 25 NC 12 P1.3_B 25 GND 12 P1.3_A 26 NC 13 P1.4_B 26 GND 13 P1.4_A 27 GND 14 P1.5_A 28 GND 5.5. Target Board DEBUG Interface (HDR1, HDR2) The DEBUG connectors (HDR1 and HDR2) provide access to the DEBUG (C2) pins of the C8051F530A parts. They are used to connect the USB Debug Adapter to the target board for in-circuit debugging and Flash programming. Table 4 shows the DEBUG pin definitions. Table 4. DEBUG Connector Pin Descriptions 8 Pin # Description 1 +3 VD (+3.3 VDC) 2, 3, 9 GND (Ground) 4 C2D 5 RST (Reset) 6 P0.6 7 C2CK 8 Not Connected 10 USB Power Rev. 0.4 C8051F53x/52x 5.6. USB to Serial Connector (P1, HDR4) A USB-to-Serial bridge interface is provided. A B-type USB connector (P1), a CP2102, and related circuits are provided to facilitate the serial connection between a PC and the U2 A-Side C8051F530A microcontroller on the target board. The RX, TX, CTS, and RTS signals of the UART side of the Bridge (CP2102) may be connected to the microcontroller by installing shorting blocks on HDR4 as shown in Table 5. Table 5. UART Connections HDR3 Connection Signals 5–6 P0.4_A to TX_A 7–8 P0.5_A to RX_A 9–10 P1.1_A to RTS_A 11–12 P1.2_A to CTS_A The BUS-Powered CP2102 uses the 5 V provided by the USB interface. 5.7. Analog I/O (TB2, J3, J4, J5) The Analog connector block (TB2) and headers J3, J4, and J5 provide Analog inputs to the C8051F530A (U2) as shown in Table 6. Headers J3, J4, and J5 connect the inputs from the Analog connector to the microcontroller pins. Table 6. Analog I/O Connections TB2 Signal Connection I/O Shorting Block P0.0_A J5 Vrefin External Reference Input or Internal Reference Output CH1 Analog Input 1 P1.6_A_MC J3 CH2 Analog Input 1 P1.7_A_MC J4 GND Ground GND — 5.8. Power Supply Options (P5, TB1, J13, J14) The target board provides two options of power supply. The first option is to use the provided 9 V power supply attached to the P5 connector. The second option is to use an external 12 V (7.5 V minimum) connected to the TB1 terminal block (pins 1 and 3). Headers J13 and J14 connect the +5 V power supply to the VREGIN pins on U1 and U2. These headers can be populated to supply power directly or depopulated to measure the operating current drawn by the corresponding C8051F530A device. Rev. 0.4 9 C8051F53x/52x 5.9. LIN Connectivity (TB1) The C8051F530A Target Board has two C8051F530A devices (U1 and U2) and two LIN transceivers (T1 and T2) to provide LIN connectivity on the target board. These devices can also be interfaced to another LIN bus using the TB1 terminal block. Table 7. LIN Connections TB1 Signal Connection +12V Supplies 12 V (7.5 V minimum) to the target board. This can be connected to the power supply of another LIN bus or any external supply. Connects the 12 V LIN bus signal to the T1 and T2 LIN transceivers. LIN GND 10 Ground Rev. 0.4 Figure 5. C8051F530A Target Board Schematic (1 of 3) C8051F53x/52x 6. Schematics Rev. 0.4 11 Figure 6. C8051F530A Target Board Schematic (2 of 3) C8051F53x/52x 12 Rev. 0.4 Figure 7. C8051F530A Target Board Schematic (3 of 3) C8051F53x/52x Rev. 0.4 13 C8051F53x/52x DOCUMENT CHANGE LIST Revision 0.2 to Revision 0.3 Updated for C8051F530A TB. Added "LIN Connectivity (TB1)‚" on page 10. Revision 0.3 to Revision 0.4 14 Updated "Software Setup‚" on page 2. Rev. 0.4 Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! IoT Portfolio www.silabs.com/IoT SW/HW Quality Support and Community www.silabs.com/simplicity www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com