X

HEGS5300
CCTV Control Keyboard
User Manual
MXMU000933 – July 2004 – Rev. A
ISSUE
DATE
A
July 2004
Rev. A
REVISIONS
Initial Release (PCN 1752).
ii
MXMU000933
07/07/04
FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at
his own expense.
CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: NOT FOR OUTDOOR USE UNLESS
ENCLOSED IN WATERPROOF HOUSING.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
UNLESS ENCLOSED IN A WATERPROOF HOUSING.
Rev. A
iii
MXMU000933
07/07/04
NOTES:
Rev. A
iv
MXMU000933
07/07/04
TABLE OF CONTENTS
SECTION 1: INTRODUCTION .................................................................................................................. 1
1.1
PRODUCT DESCRIPTION ............................................................................................................... 1
1.2
KEYBOARD OVERLAY ..................................................................................................................... 1
1.3
ICONS .............................................................................................................................................. 2
SECTION 2: SETUP AND WIRING ........................................................................................................... 3
2.1
SETUP MODE .................................................................................................................................. 3
2.2
JOYSTICK ........................................................................................................................................ 4
2.3
KEYCODE TABLE ............................................................................................................................ 4
2.4
WIRING CONNECTIONS ................................................................................................................. 6
2.5
CABLE LENGTHS ............................................................................................................................ 6
Rev. A
v
MXMU000933
07/07/04
NOTES:
Rev. A
vi
MXMU000933
07/07/04
SECTION 1:
INTRODUCTION
1.1
PRODUCT DESCRIPTION
The HEGS5300 Keyboard interfaces to the HMXAT200 and supports all power
standards. The interface board in the HMXAT200 provides 12VDC at RJ11 connectors 3
and 4 (ports 3 and 4) to power a HEGS5300 keyboard. All keyboards connected to
other ports must have their own power supply. All HEGS5300 Keyboard models are
shipped with a universal power supply for 110 or 220VAC input to +12VDC output.
1.2
KEYBOARD OVERLAY
The illustration below is the standard default overlay on a HEGS5300 keyboard.
Overlays are exchangeable and can be customized so they may vary from site to site.
MAX1000 System Controller HEGS5300
POWER
COM
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
13
14
15
16
4
5
6
7
8
9
S1 S2 S3 S4 S5 S6 S7 S8
MAX
A
Rev. A
B
C
0
D
1
A
T
MXMU000933
07/07/04
1.3
ICONS
The following icons and their descriptions may or may not be on your specific controller.
Camera
Multiplexer
Scan Select
Monitor
Play
Freeze
Insert camera into
scan
Dome / PTZ
Reverse Play
Multiplexer Zoom
Delete camera from
scan
Iris Open
Record
Multiplexer Cursor
Lock Scan
Iris Close
Stop
Full Screen
Previous Step in
Scan
Focus Far
Pause
Picture in picture
Next Step in Scan
Focus Near
Frame Forward
2 x 2 Display
Alternate Camera
Zoom Out (wide)
Frame Back
3 x 3 Display
Set
Zoom In (tele)
Rewind
4 x 4 Display
Group
View / Preshot
Fast Forward
Live Record
Night Shot
Alarm Acknowledge
Alarm Clear
MAX
Video Recorder
000
Counter Reset
1
Sequence
A
Auto Exposure
Counter Memory Stop
Enter
User Macro
Time Mode
Last / Undo
Dome Macro
Time Date Search
A
Select Monitor A
Printer Select
Maxpro Menu
Index Search
B
Select Monitor B
Print
Door Open
Next
C
Select Monitor C
Clear
Previous
D
123
Select Monitor D
+
Dub
Review
T
Text
Function
Aux
Rev. A
2
MXMU000933
07/07/04
SECTION 2:
SETUP AND WIRING
2.1
SETUP MODE
HEGS5300 keyboards are setup using the keyboard keys.
There are three user-defined settings.
1. Keyboard ID – valid ID’s 1 to 99. (Default = ID 1).
2. Baud Rate – 19K2 or 9600.
(Default = 19K2. Data format is fixed at 7 data bits, 1 stop bit, even parity).
3. Joystick speed range – There are 2 ranges of pan/tilt speeds from the analog
joystick.
The default is a range of 5 speeds (0=STOP to 5=Maximum speed).
Speed 5 is generated when the joystick is at its maximum pan or tilt position.
The second range is from 0 to 26. As before, 0=STOP and the speeds
generated are from A (slowest) through Z (fastest). Speed Z is equivalent to
speed 5 in that it is generated when the joystick is at its maximum pan or tilt
position. This feature is available when using MAX1000, version 4.27 or later.
To enter the SETUP MODE hold down the MENU key
the LCD) as the keyboard is powered up.
MAX
or the © key (to the left-of
NOTE: If the keyboard has a custom overlay, the MENU key may be located in a
different position. Therefore, the © key next to the LCD is always the preferred
option.
In SETUP MODE, the LCD guides the user in entering required information using the
numeric keypad. Press the Enter key (↵) or the ª key to the next screen.
Press the © key to return to the previous setup screen.
When the keyboard ID, baud rate, and joystick speed range have been entered, the final
setup stage stores the settings and the joystick reference position. The keyboard should
be flat on the desk when pressing the enter key (↵) at this final stage to ensure the
joystick is zeroed. Setup information is stored in non-volatile memory so the settings will
be retained if the keyboard is unplugged.
Rev. A
3
MXMU000933
07/07/04
2.2
JOYSTICK
The HEGS5300 keyboard is equipped with a 3-dimensional joystick which allows
zoom-in and zoom-out functions to be performed by twisting the top of the joystick either
clockwise (zoom-in) or counterclockwise (zoom-out). The “ZOOM IN” and “ZOOM-OUT”
buttons located on the keyboard still operate as normal.
2.3
KEYCODE TABLE
Keycode
#001
Key Name
Command
Keycode
ALARM ACK
Command
#026
#002
#027
Logical Group 9
#003
SCAN
S
#028
Logical Group 10
#004
HALT
H
#029
Logical Group 11
#005
PAUSE
P
#030
Logical Group 12
#031
DOME MENU
#006
#007
Logical Group 1
#032
#008
Logical Group 2
#033
#009
Logical Group 3
#034
#010
Logical Group 4
#035
#011
ALARM CLEAR
A
#036
#012
#037
Logical Group 13
#013
SCAN INSERT
I
#038
Logical Group 14
#014
SCAN DELETE
D
#039
Logical Group 15
#015
SET KEY
T
#040
Logical Group 16
#041
MAX MENU
?
Q
#016
#017
Logical Group 5
#042
#018
Logical Group 6
#043
MULTIPLEXER
#019
Logical Group 7
#044
FULL SCREEN
#020
Logical Group 8
#045
MULTISCREEN
#021
USER MACRO
U
#046
#022
Rev. A
Key Name
#023
LEFT ARROW
#024
LOCK KEY
#025
RIGHT ARROW
<
>
4
#047
VCR KEY
#048
FUNCTION KEY
#049
UNDO
#050
ALTERNATE
R
MXMU000933
07/07/04
2.3
KEYCODE TABLE, CONTINUED
Keycode
#051
Key Name
Command
DOOR OPEN
#052
Rev. A
Keycode
Key Name
Command
#077
[vcr-stop]
s
#078
[vcr-play]
p
#053
PRINT SELECT
#079
[vcr-record]
r
#054
PRINT FREEZE
#080
[vcr-rewind
w
#055
COLOR PRINT
#081
[vcr-pause]
u
#056
B/W PRINT
#082
[vcr-forward]
f
#057
MON A
#083
TEXT
B
#058
MON B
#084
DUB
#059
MON C
#085
REVIEW
#060
MON D
#086
[zoom-in]
G
#061
<MON>
M
#087
[zoom-out]
H
#062
<1>
1
#088
[focus-far]
B
#063
<2>
2
#089
[focus-near]
A
#064
<3>
3
#090
[iris-open]
I
#065
[up-arrow]
+
#091
[iris-close]
E
#066
<4>
4
#092
NIGHT SHOT
#067
<5>
5
#093
AUTO EXPOSURE
#068
<6>
6
#094
CALL PTZ
#069
[down-arr]
-
#095
PTZ TOUR
#070
<7>
7
#096
[tilt-up]
K
#071
<8>
8
#097
[tilt-down]
j
#072
<9>
9
#098
[pan-left]
d
#073
<CAM>
C
#099
[pan-right]
c
#074
<VIEW>
V
#100
[scroll-up]
#075
<0>
0
#101
[scroll-down]
#076
<ENTER>
.
#102
PTZ aux
5
X
x
MXMU000933
07/07/04
2.4
WIRING CONNECTIONS
RJ11 Socket on rear of keyboard
Pin 1 – Power GND
Pin 6 – Power GND
Pin 2 – TX Data
Pin 5 – RX Data
Pin 3 – Signal GND
Pin 4 – Signal GND
Pin 4 – RX Data
Pin 3 – TX Data
Pin 5 – N/C
Pin 2 – N/C
Pin 6 – 12Vdc
Pin 1 – 12Vdc
RJ Leads for Connecting Keyboards
RJ11 Socket on Keyboard
Pin 6
2.5
RJ11 Socket on rear of HMXAT200
Pin 1
CABLE LENGTHS
Refer to the following illustrations for examples of wiring connections.
NOTE: The HEGS5300 CCTV Keyboard is supplied with a standard 7-foot flat telephone
cable. It is strongly recommended that twisted-pair data cable is used from the
RJ11 Termination Box when long cable lengths are required to eliminate any
data problems. Any cable length in excess of RS232 standards (50 feet)
requires line driver units (model number PTE102).
Example 1
7-FOOT FLAT TELEPHONE CABLE
(PROVIDED WITH HEGS5300)
HEGS5300
KEYBOARD
HMXAT200 SYSTEM
CONTROLLER
POWER PROVIDED FOR CONTROLLER ON PORTS 3 & 4
NOTE: ONLY PORT 4 ON MINIMAX UNITS
Rev. A
6
MXMU000933
07/07/04
2.5
CABLE LENGTHS, CONTINUED
Example 2
2-JACK JUNCTION BOX
(PROVIDED WITH HEGS5300)
7-FOOT FLAT TELEPHONE CABLE
(PROVIDED WITH HEGS5300)
HMXAT200 SYSTEM
CONTROLLER
HEGS5300
KEYBOARD
12VDC
@1A
7-FOOT FLAT TELEPHONE CABLE
(PROVIDED WITH HEGS5300)
POWER SUPPLY
(PROVIDED WITH MODELS
HEGS5300X, A, B, & E)
Example 3
TWISTED PAIR DATA CABLE
(MAX DISTANCE = 50 FEET
SUPPLIED BY INSTALLER)
2-JACK JUNCTION BOX
(PROVIDED WITH HEGS5300)
2-JACK JUNCTION BOX
(PROVIDED WITH HEGS5300)
7-FOOT FLAT TELEPHONE CABLE
(PROVIDED WITH HEGS5300)
HMXAT200 SYSTEM
CONTROLLER
HEGS5300
KEYBOARD
12VDC
@1A
POWER SUPPLY
(PROVIDED WITH MODELS
HEGS5300X, A, B, & E)
Rev. A
7
7-FOOT FLAT TELEPHONE CABLE
(PROVIDED WITH HEGS5300)
MXMU000933
07/07/04
2.5
CABLE LENGTHS, CONTINUED
6
5
6
5
4
4
3
3
2
1
6
6
2
5
1
TO KEYBOARD
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
4
4
3
3
2
1
2
1
TO HMXAT200
KEYBOARD RJ11 CONNECTOR
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
5
HMXAT200 RJ11 CONNECTOR
12V
NC
Tx
SIG. GND
Rx
PWR GND
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
PWR GND
Tx
SIG. GND
Rx
NC
12V
Figure 1: MAX1000 Keyboard RJ11 Two-Way Junction Box (0365-0009)
Drawing MG10075
Rev. A
8
MXMU000933
07/07/04
2.5
CABLE LENGTHS, CONTINUED
Figure 2: MAX1000 Keyboard RJ12 Terminal Box Pin Utilization
Drawing MG10023
Rev. A
9
MXMU000933
07/07/04
Video Systems
www.honeywellvideo.com
1-800-796-CCTV
© 2004 Honeywell International Inc.
All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate
in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences
resulting from the use thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate such changes.