8 7 6 5 3 4 TITANIUM COMPATIBLE LASER WELDABLE NANO DUAL LOBE SINGLE ROW CONNECTOR 2 REV DCN REVISION DATE RELEASE APPROVAL - INIT RLSE 11/14/2011 J. PETRI A DCN001523 4/2/2015 • CONFIGURATION WITH THE FLANGE LOCATED AT THE TOP OF THE CONNECTOR D SRIND505 DOCUMENT REVISIONS Jim Petri 2015.04.03 12:28:00 -04'00' • DESIGNED TO LASER WELD INTO A LOW-PROFILE ELECTRONIC CHASSIS WALL D • CONFORMS TO MIL-DTL-32139 AND ARE AVAILABLE IN 9, 15, 21, 25, 31, 37 AND 51 COUNT PIN/SOCKET CONFIGURATIONS. • INCORPORATES BERYLLIUM-COPPER PIN/SOCKETS INDIVIDUALLY SEALED USING CERAMAX® PROPRIETARY CERAMIC TO ESTABLISH A DURABLE HERMETIC SEAL. • THE INTERNAL PINS CAN BE CONFIGURED TO ACCEPT INSULATED WIRE, AUTOMATIC WIRE BONDS, RIBBON WELDS, OR SOLDER CONNECTIONS. 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. INTERFACE AND MOUNTING HOLES IN ACCORDANCE WITH MIL-DTL-32139/2. 3. MATERIALS: CONTACT: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B196/197. INSULATOR: CERAMAX PROPRIETARY CERAMIC. WELD FLANGE: TITANIUM GRADE 4 IN ACCORDANCE WITH ASTM B265. C 4. FINISH: CONTACTS: NICKEL PLATE PER QQ-N-290, .000100 / .000250 THICK. HARD GOLD STRIKE PER ASTM B488-01, TYPE II CODE C, .000020/.000050 THICK. GOLD PLATE PER ASTM B488-01, TYPE III, CODE A, .000050/.000100 THICK. PLATE ENTIRE EXPOSED PIN, BOTH ENDS. PLATING IN SOCKETS NOT REQUIRED BENEATH BLEED HOLE. C SHELL: PASSIVATED 5. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBERS INDICATING PIN COUNT AND CONFIGURATION (SEE SHEETS 2 AND 3): EXAMPLE: SRIND505 - 25 - A 1 DETAILED CONFIGURATION PIN END STYLE (SEE VIEW A) NUMBER OF CONTACTS, X BASE NUMBER B B A A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION (321) 254-4067 www.srihermetics.com a division of WINCHESTER TITLE CONNECTOR, 250DL, TOP FLANGE, SINGLE ROW, TC LBW SIZE DOCUMENT A DO NOT SCALE DRAWING FORM 300067 REV A 7 6 5 4 3 SCALE 6:1 2 CAGE CODE SRIND505 3PJY7 SHEET 1 REV A 1 OF 3 8 6 7 5 3 4 2 SRIND505 DOCUMENT W A .010 D D .162 O .010±.002 .003 MAX BRK PIN EXTENSION (SEE SH 3) WELD FLANGE C NUMBER OF CONTACTS W M Y 9 .580 .560 .563 15 .730 .710 .713 21 .880 .860 .863 25 .980 .960 .963 31 1.130 1.110 1.113 37 1.280 1.260 1.263 51 1.630 1.610 1.613 .225 C Y .001 CONTACT B PIN END STYLE: A-STRAIGHT CUT B-WIREBOND FLAT VIEW A B .145 .001 .003 MAX BRK 2XR O 2X R HOLE DETAIL .142±.001 A A M .001 DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION (321) 254-4067 www.srihermetics.com a division of WINCHESTER TITLE CONNECTOR, 250DL, TOP FLANGE, SINGLE ROW, TC LBW SIZE DOCUMENT A DO NOT SCALE DRAWING FORM 300067 REV A 7 6 5 4 3 SCALE 6:1 2 CAGE CODE SRIND505 3PJY7 SHEET 1 REV A 2 OF 3 8 6 7 5 4 STRAIGHT PIN END STYLE, A 3 2 SRIND505 DOCUMENT WIREBOND FLAT PIN END STYLE, B D D PIN EXTENSION A PIN EXTENSION A .015 A .005 MIN THICK .012 MIN WIDE C C PART NUMBER A PART NUMBER A SRIND505 - X - A 1 .100 SRIND505 - X - B 1 .100 SRIND505 - X - B2 .032 B B A A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION (321) 254-4067 www.srihermetics.com a division of WINCHESTER TITLE CONNECTOR, 250DL, TOP FLANGE, SINGLE ROW, TC LBW SIZE DOCUMENT A DO NOT SCALE DRAWING FORM 300067 REV A 7 6 5 4 3 SCALE 6:1 2 CAGE CODE SRIND505 3PJY7 SHEET 1 REV A 3 OF 3