For more information, please visit the product page. PART NUMBER: CPE-267 page 1 of 5 date 02/2010 DESCRIPTION: piezo audio transducer SPECIFICATONS operating frequency rated voltage operating voltage range current consumption sound pressure level tone operating tempurature storage tempurature dimensions weight material terminal RoHS dustproof/waterproof level 2.8 ± 0.5 kHz 12 V dc 6 ~ 14 V dc 35 mA max. at 12 V dc 85 dB min. at 30 cm/12 V dc continuous at 12 V dc -30 ~ +85° C -40 ~ +95° C ø25 x H16 mm 41 g max. ABS UL-94 1/16” HB high heat (black) wire type yes IP67 IEC standard 529 edition 2.0(1989) APPEARANCE DRAWING tolerance: ±0.5 units: mm CUI,INC. G ˨˟˄˃˃ˊ˟˙ʳ˅˅˔˪˚ ˥˸˷ ˕˿˴˶˾ ʻ˦˸˴˿˸˷ʳ˧̌̃˸ʼ 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. page 2 of 5 date 02/2010 DESCRIPTION: piezo audio transducer PART NUMBER: CPE-267 VOLTAGE: SOUND PRESSURE LEVEL / CURRENT CONSUMPTION CHARACTERISTICS ˄˃ˈ ˄˃˃ ˣ ˌ˃ ˋˈ ˋ˃ ˊˈ ˆˈ ˜ ˊ˃ ˆ˃ ˅ˈ ˅˃ ˄ˈ ˄˃ ˉ ˋ ˄˃ ˄˅ ˄ˇ ˩̂˿̇˴˺˸ʻ˩˗˖ʼ MEASUREMENT METHOD S.P.L. Measuring Circuit Mic: RION S.P.L. meter UC30 or equivalent S.G.: Hewlett Packard 33120A function generator or equivalent 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 ˄ˉ ˖̈̅̅˸́̇ʳ˖̂́̆̈̀̃̇˼̂́ʻ̀˔ʼ ˦̂̈́˷ʳˣ̅˸̆̆̈̅˸ʳ˟˸̉˸˿ʻ˷˕ʼʳʳ ˌˈ For more information, please visit the product page. page 3 of 5 date 02/2010 DESCRIPTION: piezo audio transducer PART NUMBER: CPE-267 MECHANICAL CHARACTERISTICS item solderability (connector excepted) lead wire pull strength vibration drop test test condition Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of 270 ±5°C for 3 ±0.5 seconds. The pull force shall be applied to double lead wire: Horizontal 3.0N (0.306 kg) for 30 seconds Vertical 2.0N (0.204 kg) for 30 seconds The buzzer shall be measured after applying a vibration amplitude of 1.5 mm with 10 to 55 Hz band of vibration frequency to each of the 3 perpendicular directions for 2 hours. The part will be dropped from a height of 75 cm onto a 40 mm thick wooden board 3 times in 3 axes (X, Y, Z) for a total of 9 drops. evaluation standard 90% min. of the lead terminals will be wet with solder (except the edge of the terminal). test condition After being placed in a chamber at +95°C for 240 hours. After being placed in a chamber at -40°C for 240 hours. After being placed in a chamber at +40°C and 90±5% relative humidity for 240 hours. The part shall be subjected to 5 cycles. One cycle will consist of: evaluation standard No damage or cutting off. The value of oscillation frequency/current consumption should be ±10% of the initial measurements. The SPL should be within ±10dB compared with the initial measurement. ENVIRONMENT TEST item high temp. test low temp. test humidity test temp. cycle test +95к +25к +25кʳ -40к 0.5hr The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. 0.5hr 0.25 0.5hr 0.5hr 0.5hr 0.25 3hours 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. page 4 of 5 date 02/2010 DESCRIPTION: piezo audio transducer PART NUMBER: CPE-267 RELIABILITY TEST item operating (life test) test condition 1. Continuous life test: The part will be subjected to 48 hours of continuous operation at +70°C with rated voltage applied. 2. Intermittent life test: A duty cycle of 1 minute on, 1 minute off, a minimum of 5,000 times at room temp (+25 ±2°C) with rated voltage applied. evaluation standard The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. TEST CONDITIONS standard test condition judgement test condition a) tempurature: +5 ~ +35°C a) tempurature: +25 ±2°C b) humidity: 45 - 85% b) humidity: 60 - 70% c) pressure: 860-1060 mbar c) pressure: 860-1060 mbar 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. PART NUMBER: CPE-267 page 5 of 5 date 02/2010 DESCRIPTION: piezo audio transducer PACKAGING 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383