DFM800XXM45-TS001

DFM800XXM45-TS001
Fast Recovery Diode Module
Replaces DS6096-1
DS6096-2 October 2013 (LN31066)
FEATURES
KEY PARAMETERS

VRRM
VF
IF
IFM
10.2kV Isolation Package

Low Reverse Recovery Charge

High Switching Speed

Low Forward Volt Drop

Isolated AlSiC Base With AlN Substrates

Dual Diodes Can Be Paralleled For 1600A Rating
4500V
2.8V
800A
1600A
(typ)
(max)
(max)
7(K)
5(K)
6(A)
4(A)
APPLICATIONS

Chopper Diodes

Boost and Buck Converters

Free-wheel Circuits

Snubber Circuit

Resonant Converters

Induction Heating

Multi-level Switch Inverters
External connection required for a single 1600A diode
The DFM800XXM45-TS001 is a dual 4500V, fast
recovery diode (FRD) module. Designed for low
power loss, the module is suitable for a variety of high
voltage applications in motor drives and power
conversion.
Fig. 1 Circuit configuration
Fast switching times and low reverse recovery losses
allow high frequency operation, making the device
suitable for the latest drive designs employing PWM
and high frequency switching.
The module incorporates an electrically isolated base
plate and low inductance construction enabling circuit
designers to optimise circuit layouts and utilise
grounded heat sinks for safety.
ORDERING INFORMATION
Order As:
DFM800XXM45-TS001
Outline type code: X
(See Fig. 7 for further information)
Fig. 2 Package
Note: When ordering, please use the complete part
number
1 /6
www.dynexsemi.com
DFM800XXM45-TS001
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under ‘Absolute Maximum Ratings’ may cause permanent damage to the device. In
extreme conditions, as with all semiconductors, this may include potentially hazardous rupture of the package.
Appropriate safety precautions should always be followed. Exposure to Absolute Maximum Ratings may affect
device reliability.
Tcase = 25°C unless stated otherwise
Symbol
VRRM
Parameter
Test Conditions
Max.
Units
Repetitive peak reverse voltage
Tj = 125°C
4500
V
IF
Forward current (per arm)
DC, Tcase = 65°C
800
A
IFM
Max. forward current
Tcase = 115°C, tp = 1ms
1600
A
I t value fuse current rating
VR = 0, tp = 10ms, Tj = 125°C
300
kA s
Pmax
Max. power dissipation
Tcase = 25°C, Tj = 125°C
4160
W
Visol
Isolation voltage – per module
Commoned terminals to base plate.
AC RMS, 1 min, 50Hz
10.2
kV
QPD
Partial discharge – per module
IEC1287, V1 = 6900V, V2 = 5100V, 50Hz RMS
10
pC
2
It
2
2
THERMAL AND MECHANICAL RATINGS
Internal insulation material:
AlN
Baseplate material:
AlSiC
Creepage distance:
56mm
Clearance:
26mm
CTI (Comparative Tracking Index):
> 600
Symbol
Parameter
Min
Typ.
Max
Units
-
-
24
°C/kW
-
-
8
°C/kW
Junction temperature
-40
-
125
°C
Storage temperature range
-40
-
125
°C
Mounting – M6
-
-
5
Nm
Electrical connections – M8
-
-
10
Nm
Rth(j-c)
Thermal resistance (per arm)
Rth(c-h)
Thermal resistance –
case to heatsink (per module)
Tj
Tstg
Screw Torque
Test Conditions
Continuous dissipation –
junction to case
Mounting torque 5Nm
(with mounting grease)
2/6
www.dynexsemi.com
DFM800XXM45-TS001
STATIC ELECTRICAL CHARACTERISTICS – PER ARM
Tcase = 25°C unless stated otherwise.
Symbol
Parameter
IRM
Peak reverse current
VF
Forward voltage
LM
Inductance
Test Conditions
Min
Typ
VR = 4500V, Tj = 125°C
Max
Units
60
mA
IF = 800A
2.8
V
IF = 800A, Tj = 125°C
3.2
V
40
nH
-
DYNAMIC ELECTRICAL CHARACTERISTICS – PER ARM
Tcase = 25°C unless stated otherwise (when used with DIM800XSM45-TS001)
Symbol
Parameter
Qrr
Reverse recovery charge
Irr
Peak reverse recovery current
Erec
Reverse recovery energy
Test Conditions
Min
Typ.
Max
Units
880
μC
VR =2800V
680
A
dIF/dt = 2000/μs
1480
mJ
IF = 800A
Tcase = 125°C unless stated otherwise (when used with DIM800XSM45-TS001)
Parameter
Symbol
Qrr
Reverse recovery charge
Irr
Peak reverse recovery current
Erec
Reverse recovery energy
Test Conditions
Min
Typ.
Max
Units
1450
μC
VR = 2800V
750
A
dIF/dt = 2000A/μs
2500
mJ
IF = 800A
3 /6
www.dynexsemi.com
DFM800XXM45-TS001
Fig. 3 Diode typical forward characteristics
Fig. 4 Transient thermal impedance
Fig. 5 DC current rating vs case temperature
Fig. 6 Reverse Bias Safe Operating Area (RBSOA)
4/6
www.dynexsemi.com
DFM800XXM45-TS001
PACKAGE DETAILS
For further package information, please visit our website or contact Customer Services.
All dimensions in mm, unless stated otherwise.
DO NOT SCALE.
130±0.5
4 x M8
57 ±0.25
57 ±0.25
screwing depth
max. 16
44 ±0.2
140 ±0.5
124 ±0.25
18 ±0.1
7
36.5±0.2
6 xØ 7
61.2 ±0.3
16.5 ±0.2
external connection
5(C)
6(A)
4(A)
5 ±0.2
48
+1.5
-0.0
7(C)
external connection
Nominal Weight: 1100g
Module Outline Type Code:
X
Fig. 7 Module outline drawing
5 /6
www.dynexsemi.com
DFM800XXM45-TS001
IMPORTANT INFORMATION:
This publication is provided for information only and not for resale.
The products and information in this publication are intended for use by appropriately trained technical personnel.
Due to the diversity of product applications, the information contained herein is provided as a general guide only and does n ot
constitute any guarantee of suitability for use in a specific application. The user must evaluate the suitability of the product and
the completeness of the product data for the application. The user is responsible for product selection and ensuring all safety
and any warning requirements are met. Should additional product information be needed please contact Customer Service.
Although we have endeavoured to carefully compile the information in this publication it may contain inaccuracies or
typographical errors. The information is provided without any warranty or guarantee of any kind.
This publication is an uncontrolled document and is subject to change without notice. When referring to it please ensure that it
is the most up to date version and has not been superseded.
The products are not intended for use in applications where a failure or malfunction may cause loss of life, injury or damage to
property. The user must ensure that appropriate safety precautions are taken to prevent or mitigate the consequences of a
product failure or malfunction.
The products must not be touched when operating because there is a danger of electrocution or severe burning. Always use
protective safety equipment such as appropriate shields for the product and wear safety glasses. Even when disconnected any
electric charge remaining in the product must be discharged and allowed to cool before safe handling using protective gloves.
Extended exposure to conditions outside the product ratings may affect reliability leading to premature product failure. Use
outside the product ratings is likely to cause permanent damage to the product. In extreme conditions, as with all
semiconductors, this may include potentially hazardous rupture, a large current to flow or high voltage arcing, resulting in fire or
explosion. Appropriate application design and safety precautions should always be followed to protect persons and property.
Product Status & Product Ordering:
We annotate datasheets in the top right hand corner of the front page, to indicate product status if it is not yet fully approved for
production. The annotations are as follows:Target Information:
This is the most tentative form of information and represents a very preliminary specification.
No actual design work on the product has been started.
Preliminary Information:
The product design is complete and final characterisation for volume production is in progress.
The datasheet represents the product as it is now understood but details may change.
No Annotation:
The product has been approved for production and unless otherwise notified by Dynex any
product ordered will be supplied to the current version of the data sheet prevailing at the
time of our order acknowledgement.
All products and materials are sold and services provided subject to Dynex’s conditions of sale, which are available
on request.
Any brand names and product names used in this publication are trademarks, registered trademarks or trade
names of their respective owners.
HEADQUARTERS OPERATIONS
CUSTOMER SERVICE
DYNEX SEMICONDUCTOR LTD
Doddington Road, Lincoln, Lincolnshire, LN6 3LF,
United Kingdom
Fax:
+44(0)1522 500550
Tel:
+44(0)1522 500500
Web:
http://www.dynexsemi.com
DYNEX SEMICONDUCTOR LTD
Doddington Road, Lincoln, Lincolnshire, LN6 3LF,
United Kingdom
Fax:
+44(0)1522 500020
Tel:
+44(0)1522 502753 / 502901
Email: [email protected]
 Dynex Semiconductor Ltd. 2013.
Technical Documentation – Not for resale.
6/6
www.dynexsemi.com