MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS FEATURES x Antenna coupling and line bypass capacitor x Across-the-line capacitor x Recognized by UL,VDE(ENEC), CSA x Temperature characteristic: SL,Y5P,Y5U,Y5V x Rated capacitance : 10pF~10nF x Capacitance tolerance : ±5%, ±10%, ±20% x Passive flammability category: C x Operating temperature range: -40ºC ~+125ºC x Automatic insertion can be, and save costs UL E197475 VDE PART NUMBER SYSTEM MCH 11 F 472 M S L 7 B S Internal control code Meritek Series Code MCH X1/Y1 MCY X1/Y2 Packing Style Code Type Nominal Body Diameter Temperature Characteristic Code S SL B Y5P E Y5U B Bulk T Taping Lead Space F Y5V Code 0 9 Pitch(mm) 10.0±1.0 9.0±1.0 7 7.5±1.0 Capacitance (unit: pF) Lead Length First 2 digits are significant 3rd digit is multiplier. "R" indicates decimal for values below 10pF L - indicate the length is long and define in specification, other codes indicate length defined by customer Capacitance Tolerance Lead Style Code Value J ±5% K ±10% M ±20% Code Type S straight Y Y kink O out kink SPECIFICATIONS Item Temperature characteristics Capacitance Dissipation Factor (%) Insulation Resistance ( I.R. ) Standard Dielectric Capacitance Deviation SL +350 ~ -1000ppm/ºC Dielectric Capacitance Deviation Y5P less then ±10% Y5U less then +22%/-56% Y5V less then +22%/-82% To be within the specified tolerance Dielectric Value Y5P, Y5U D.F. ≤ 2.5% Y5V D.F. ≤ 5.0% Q ≥ 400+20C (C < 30pF) SL Q>1,000 (C ≥ 30pF) 10,000MΩ, min. No breakdown Dielectric Strength Test method Test temperature range : +25ºC~+85ºC Test temperature range : -30ºC~+85ºC Test condition : SL - 1.0MHz±20%, 1.0±0.2Vrms Y5P,Y5U,Y5V - 1.0kHz±20%, 1.0±0.2Vrms Applied voltage : 500Vdc, Charge/discharge current: 50mA, max Duration: 60±3.0sec. Test voltage: MCH - AC4000V, MCY - AC2600V Between leads Test duration: 60seconds Charge/discharge current: 50mA, max Body insulation The terminals of the capacitor shall be connected together, a metal foil shall be closely wrapped around the body of the capacitor to the distance of about 3~4 mm from each terminal, a voltage is applied between the capacitor lead wires and the metal balls for 1 minute. Caution: 1. Test duration: 1~5 seconds for lot production. 2. Voltage applied method for dielectric withstand voltage test shall be raised from near zero to the test voltage or with the zero cross 3. Test environment: unless otherwise specified, test and measurement shall be made at the standard conditions Temperature range Relative humidity Atmospheric pressure +15ºC~+35ºC 45%~85% 86~106kPa If the validity of mesaurement value determined under the standard condition is questioned or if there occurs a special MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS need of evaluating the test results, capacitors shall be tested and measured at the determinant ambient conditions : Temperature range Relative humidity Atmospheric pressure 25±1ºC 48%~52% 86~106kPa 40/125/56/C Climatic Category LEAD STYLE Straight lead MCx xx x xxx xSxxxS Y kink lead MCx xx x xxx xYxxxS Out kink lead MCx xx x xxx xOxxxS Note Dimension : mm For bulk packing LL is 3.5±1.0mm, 4.0±1.0mm,5.0±1.0mm,6.0±1.0mm,7.0±1.0mm, 8.0±1.0mm are available for customer requirement Type Part no. Capacitance (pF) Tolerance MCH (Y1) - AC250V/500V STANDARD LIST AND DIMENSIONS MCH07B100KxxxxS MCH07B150KxxxxS MCH07B180KxxxxS MCH07B220KxxxxS MCH08B250KxxxxS MCH08B270KxxxxS MCH08B330KxxxxS MCH08B390KxxxxS MCH08B470KxxxxS MCH08B560KxxxxS MCH09B680KxxxxS MCH10B820KxxxxS MCH07B101KxxxxS MCH07B151KxxxxS MCH07B221KxxxxS MCH08B271KxxxxS MCH08B331KxxxxS MCH09B391KxxxxS MCH09B471KxxxxS MCH10B561KxxxxS MCH10B681KxxxxS MCH11B821KxxxxS MCH12B102KxxxxS 10 15 18 22 25 27 33 39 47 56 68 82 100 150 220 270 330 390 470 560 680 820 1000 ±10% BD, max 7.5 7.5 7.5 7.5 8.0 8.0 8.0 8.0 8.0 8.0 9.0 10.0 7.5 7.5 7.5 8.5 8.5 9.0 9.0 10.0 10.0 11.5 12.5 Dimensions(mm) BT, max 5.5 LS±1.0 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK MCY(Y2) - AC250V/300V RoHS MCH16B152KxxxxS MCH18B222KxxxxS MCH08E102MxxxxS MCH10E152MxxxxS MCH11E222MxxxxS MCH13E332MxxxxS MCH14E392MxxxxS MCH15E472MxxxxS MCH07S100KxxxxS MCH07S120KxxxxS MCH07S180KxxxxS MCH07S220KxxxxS MCH08S250KxxxxS MCH08S270KxxxxS MCH08S330KxxxxS MCH08S390KxxxxS MCH08S470KxxxxS MCH08S560KxxxxS MCH09S680KxxxxS MCH10S820KxxxxS MCH07F102MxxxxS MCH08F152MxxxxS MCH09F222MxxxxS MCH11F332MxxxxS MCH12F472MxxxxS MCY07B100KxxxxS MCY07B150KxxxxS MCY07B180KxxxxS MCY07B220KxxxxS MCY07B250KxxxxS MCY08B270KxxxxS MCY08B330KxxxxS MCY08B390KxxxxS MCY09B470KxxxxS MCY09B560KxxxxS MCY10B680KxxxxS MCY11B820KxxxxS MCY07B101KxxxxS MCY07B151KxxxxS MCY07B221KxxxxS MCY07B271KxxxxS MCY07B331KxxxxS MCY09B391KxxxxS MCY08B471KxxxxS MCY10B561KxxxxS MCY10B681KxxxxS MCY11B821KxxxxS MCY11B102KxxxxS MCY13B152KxxxxS MCY15B222KxxxxS MCY08E102MxxxxS MCY09E152MxxxxS MCY10E222MxxxxS MCY11E332MxxxxS MCY13E472MxxxxS MCY07F102MxxxxS MCY08F152MxxxxS MCY09F222MxxxxS MCY10F332MxxxxS MCY11F472MxxxxS MCY12F682MxxxxS MCY15F822MxxxxS MCY16F103MxxxxS 1500 2200 1000 1500 2200 3300 3900 4700 10 12 18 22 25 27 33 39 47 56 68 82 1000 1500 2200 3300 4700 10 15 18 22 25 27 33 39 47 56 68 82 100 150 220 270 330 390 470 560 680 820 1000 1500 2200 1000 1500 2200 3300 4700 1000 1500 2200 3300 4700 6800 8200 10000 NOTE : Lead spacing can adjust by customer request. ±20% ±10% ±20% ±10% ±20% ±20% 16.5 18.5 8.5 10.0 11.5 13.5 14.5 15.5 7.5 7.5 7.5 7.5 8.0 8.0 8.0 8.0 8.0 8.0 9.0 10.0 7.5 8.5 9.0 11.5 12.5 7.5 7.5 7.5 7.5 7.5 8.0 8.0 8.5 9.0 9.0 10.0 11.0 7.0 7.5 7.5 7.5 7.5 9.0 8.0 10.0 10.0 11.5 11.5 13.5 15.5 8.0 9.5 10.0 11.0 13.5 7.5 8.0 9.0 10.0 11.5 12.5 15.5 16.5 4.5 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10 10 7.5 7.5 7.5 10 10 7.5 7.5 7.5 10 10 10 10 10 MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS RELIABILITY Item Terminal strength Tensile Bending Solder ability Temperature characteristics Specifications Test condition Termination not to be broken or loosened Fix the capacitor body, apply the force gradually to each lead in the radial direction of the capacitor until reaching 1.0kg and then keep applied the force 10±1.0second. Termination not to be broken or loosened Each lead wire shall be subjected to a force of 0.5kg and then bend 90º at the point of degree in one direction, each wire is then returned to the original position and bend per 2~3 seconds, two times. Lead wire to soldered up to the dipped Solder temperature: 245ºC±5ºC end point with no gap in the axial direction Solder time: 3.0±0.5seconds over 75% of the circumferential direction. ∆C should be got from the capacitor @25ºC, Type Tempe. range ∆C after capacitor measured from minimum Y5P -30ºC~+85ºC ±10% temperature to maximun temperature, it should Y5U -30ºC~+85ºC +22%~-56% be calculated from the formula below Y5V -30ºC~+85ºC +22%~-82% ሺʹ െ ͳሻ SL +25ºC~+85ºC +350~-1000ppm/ºC ൈ ͳͲͲΨ ͳ Resistance to soldering heat 1. Appearance: no damage 2. ∆C (change from the value before) Y5P: ±5% Y5U: ±15% Y5V: ±20% SL: ±5.0% 3. Dielectric withstand voltage: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. Thermal shock 1. Appearance: no mechanical damage 2. ∆C ( capacitance change ) Y5P: ±10% Y5U: ±20% Y5V: ±30% SL: ±5.0% 3. Quality factor / dissipation factor Y5P, Y5U: 5%, max. Y5V:7.5%, max SL < 10pF, Q≥200+10C(pF) 30pF > SL ≥ 10pF, Q≥275+2.5C(pF) SL ≥ 30pF, Q≥350 4. Insulation resistance: 1000MΩ min. 5. Dielectric strength: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. 1. Appearance: no mechanical damage 2. ∆C ( capacitance change ) Y5P: ±10% Y5U: ±20% Y5V: ±30% SL: ±5.0% 3. Quality factor / dissipation factor Y5P, Y5U: 5%, max. Y5V:7.5%, max SL < 10pF, Q≥200+10C(pF) 30pF > SL ≥ 10pF, Q≥275+2.5C(pF) Humidity C1: capacitance at standard temperature(25ºC) C2: capacitance at each temperature Solder temperature 260ºC±5ºC. The depth of immersion shall be a position 1.5~2.0mm from the seating plane, using a thermal insulation screen of 1.5±0.5mm thickness and solder time 10±1.0seconds. Pre-treatment Capacitor shall be stored at 85ºC±2ºC for 1 hour, then placed at room condition for 24±2hours before initial measurements. Post-treatment Capacitor shall be stored for 1 to 2 hours at room condition. The capacitor should be subjected to 5 temperature cycles. step1~step 4 below construct one cycle. step Temperature(ºC) Duration 1 -40±3.0 30 minutes 2 Room temperature < 5.0 minutes 3 125±3.0 30 minutes 4 Room termperature < 5.0 minutes Stay specimen 24 hours at room temperature after 5 cycles Before test: measure capacitance/DF after curing 40ºC±5.0ºC for 24hours. Ambient temperature: 40±2.0ºC Relative humidity: 90~95%. R.H. Duration: 500 +24/-0 hours After test: stay 24 hours at room temperature. MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS Humidity loading High temperature load exposure Vibration resistance High temperature shelf Low temperature shelf SL ≥ 30pF, Q≥350 4. Insulation resistance: 1000MΩ min. 5. Dielectric strength: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. 1. Appearance: no mechanical damage 2. ∆C ( capacitance change ) Y5P: ±10% Y5U: ±20% Y5V: ±30% SL: ±7.5% 3. Quality factor / dissipation factor Y5P, Y5U: 5.0%, max. Y5V:7.5%, max SL < 10pF, Q≥200+10C(pF) 30pF > SL ≥ 10pF, Q≥275+2.5C(pF) SL ≥ 30pF, Q≥350 4. Insulation resistance: 500MΩ min. 5. Dielectric strength: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. 1. Appearance: no mechanical damage 2. ∆C ( capacitance change ) Y5P: ±10% Y5U: ±20% Y5V: ±30% SL: ±3.0% 3. Quality factor / dissipation factor Y5P, Y5U: 5%, max. Y5V:7.5%, max SL < 10pF, Q≥200+10C(pF) 30pF > SL ≥ 10pF, Q≥275+2.5C(pF) SL ≥ 30pF, Q≥350 4. Insulation resistance: 1000MΩ min. 5. Dielectric strength: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. 1. Appearance: no marked defect 2. Capacitance: specification values range 3. Quality factor or dissipation factor: specification values range 4. Insulation resistance: 10000MΩ min. 5. Dielectric strength: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. 1. Appearance: no mechanical damage 2. ∆C ( capacitance change ) Y5P: ±10% Y5U: ±20% Y5V: ±30% SL: ±5.0% 3. Quality factor / dissipation factor Y5P, Y5U: 5%, max. Y5V:7.5%, max SL < 10pF, Q≥200+10C(pF) 30pF > SL ≥ 10pF, Q≥275+2.5C(pF) SL ≥ 30pF, Q≥350 4. Insulation resistance: 2000MΩ min. 5. Dielectric strength: Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. 1. Appearance: no mechanical damage 2. ∆C ( capacitance change ) Y5P: ±10% Y5U: ±20% Y5V: ±30% SL: ±5.0% 3. Quality factor / dissipation factor Y5P, Y5U: 5%, max. Y5V:7.5%, max SL < 10pF, Q≥200+10C(pF) 30pF > SL ≥ 10pF, Q≥275+2.5C(pF) SL ≥ 30pF, Q≥350 4. Insulation resistance: 2000MΩ min. 5. Dielectric strength: Before test: measure capacitance/DF after curing 40ºC±5.0ºC for 24hours. Ambient temperature: 40±2.0ºC Relative humidity: 90~95%. R.H. Loading voltage: rated voltage Duration: 500 +24/-0 hours After test: stay 24 hours at room temperature. Before test: measure capacitance/DF after curing 40ºC±5.0ºC for 24hours. Ambient temperature: 125±2.0ºC Loading voltage: 1.5 x rated voltage Duration: 1000 +48/-0 hours After test: stay 24 hours at room temperature The capacitor should be limly soldered to the supporting lead wire and vibrated at a frequency range of 10 to 55Hz, 15mm in total amplitude, with about a minute rate of vibration change from 10Hz to 55Hz, then back to 10Hz. Apply for a total of 6 hours, 2 hours each in 3 mutually perpendicular direction Before test: resistance to soldering heat test. Ambient temperature: 125ºC±2ºC Duration: 1000 +48/-0 hours After test: stay 24 hours at room temperature Before test: resistance to soldering heat test Ambient temperature: -40ºC±3ºC Duration: 1000 +48/-0 seconds After test: stay 24 hours at room temperature. MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS Y1 - AC4000V, Y2 - AC2600V Duration: 3 seconds. The burning duration should not exceed 30 seconds. The tissue paper should not ignite. Passive flammability The capacitor under test should be held in the location which best promotes burning. Each specimen should only be exposed once to flame Time of exposure to flame: 30 seconds. Length of flame: 12±1.0mm Gas burner: length 35mm min. Inside diameter: 0.5±0.1mm Outside diameter: 0.9mm max. Gas: Butane gas purity 95% min. SOLDERING RECOMMENDATION WAVE SOLDERING PROFILE Temperature 260ºC Pre-heating Cooling C 5º 0 ºC/ s econ ds Soldering ,m ds on ≈ 20 ec /s ax environment temp. (1 ºC ~ 3º C )/s ec on ds 100ºC > 80 sec < 1 sec 10±1.0sec Duration RECOMMENDED REWORKING CONDITIONS WITH SOLDERING IRON x temperature of soldering Iron-tip : 350ºC±10ºC. x soldering time : 3.0 seconds, max. x welding position distance coating position : 2.0mm (min.) MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS PACKING STRAIGHT Figure A Figure B Figure C Dimension (mm) Symbol LS BS HS HL BH ∆S ∆H TW ITW TC TIG LC HD TT Item Lead to lead distance Pitch of component Feed hole pitch Feed hole center to lead center Feed hole center to body center Component aligment R-L Deviation across tape F-R Tape width Hold down tape width Hold position Hole down tape position Height of component from tape center Feed hole diameter Total tape thickness HS=12.7 FIG B 7.5±1.0 12.7±1.0 12.7±0.3 2.6±0.7 6.35±1.3 0±2.0 0±2.0 18.0±1.0 8,min. 9.0±0.5 5.0 max. 20.0 +1.5/-1.0 4.0±0.2 0.6±0.3 FIG A 10±1.0 25.4±1.0 12.7±0.3 7.7±0.7 12.7±1.3 0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 20.0 +1.5/-1.0 4.0±0.2 0.6±0.3 HS=15.0 FIG B FIG C 7.5±1.0 10±1.0 15.0±1.0 15±1.0 15.0±0.3 15±0.3 3.75±0.7 -7.5±1.3 -0±2.0 0±2.0 0±2.0 0±2.0 18.0±1.0 18.0±1.0 8, min. 8, min. 9.0±0.5 9.0±0.5 5.0 max. 5.0 max. 20.0 +1.5/-1.0 20.0 +1.5/-1.0 4.0±0.2 4.0±0.2 0.6±0.3 0.6±0.3 MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS OUT KINK FIGURE A FIGURE B FIGURE C Dimension (mm) Symbol LS BS HS HL BH ∆S ∆H TW ITW TC TIG LC HD TT Item Lead to lead distance Pitch of component Feed hole pitch Feed hole center to lead center Feed hole center to body center Component aligment R-L Deviation across tape F-R Tape width Hold down tape width Hold position Hole down tape position Height of component from tape center Feed hole diameter Total tape thickness HS=12.7 FIG B 7.5±1.0 12.7±1.0 12.7±0.3 2.6±0.7 6.35±1.3 0±2.0 0±2.0 18.0±1.0 8,min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 HS=15.0 FIG A 10±1.0 25.4±1.0 12.7±0.3 7.7±0.7 12.7±1.3 0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 FIG B 7.5±1.0 15.0±1.0 15.0±0.3 3.75±0.7 7.5±1.3 0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 FIG C 10±1.0 15±1.0 15±0.3 --0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 MCH/MCY-S Safety Recognized Ceramic Capacitor Series MERITEK RoHS Y KINK FIGURE A FIGURE B FIGURE C Dimension (mm) Symbol LS BS HS HL BH ∆S ∆H TW ITW TC TIG LC HD TT Item Lead to lead distance Pitch of component Feed hole pitch Feed hole center to lead center Feed hole center to body center Component aligment R-L Deviation across tape F-R Tape width Hold down tape width Hold position Hole down tape position Height of component from tape center Feed hole diameter Total tape thickness HS=12.7 FIG B 7.5±1.0 12.7±1.0 12.7±0.3 2.6±0.7 6.35±1.3 0±2.0 0±2.0 18.0±1.0 8,min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 HS=15.0 FIG A 10±1.0 25.4±1.0 12.7±0.3 7.7±0.7 12.7±1.3 0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 FIG B 7.5±1.0 15.0±1.0 15.0±0.3 3.75±0.7 7.5±1.3 0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3 FIG C 10±1.0 15±1.0 15±0.3 --0±2.0 0±2.0 18.0±1.0 8, min. 9.0±0.5 5.0 max. 16±0.5 4.0±0.2 0.6±0.3