Data Sheet

LPC1102/1104
32-bit ARM Cortex-M0 microcontroller; 32 kB flash and 8 kB
SRAM
Rev. 7 — 26 September 2013
Product data sheet
1. General description
The LPC1102/1104 are an ARM Cortex-M0 based, low-cost 32-bit MCU, designed for
8/16-bit microcontroller applications, offering performance, low power, simple instruction
set and memory addressing together with reduced code size compared to existing 8/16-bit
architectures.
The LPC1102/1104 operate at CPU frequencies of up to 50 MHz.
The peripheral complement of the LPC1102/1104 includes 32 kB of flash memory, 8 kB of
data memory, one RS-485/EIA-485 UART, one SPI interface with SSP features, four
general purpose counter/timers, a 10-bit ADC, and 11 general purpose I/O pins.
Remark: The LPC1104 has a revised pinout and contains several features not found in
the LPC1102:
•
•
•
•
•
Two extra GPIO pins (PIO0_1 and PIO0_6).
Extra match output (CT32B0_MAT2).
CLKOUT feature.
Easier re-entry to ISP via PIO0_1.
SSP0_CLK available on two pins (A1 and A2) to support debugging of SSP
communication.
• Better positioning of the XTALIN pin for easier PCB layout.
2. Features and benefits
 System:
 ARM Cortex-M0 processor, running at frequencies of up to 50 MHz.
 ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).
 Serial Wire Debug.
 System tick timer.
 Memory:
 32 kB on-chip flash programming memory.
 8 kB SRAM.
 In-Application Programming (IAP) and In-System Programming (ISP) support via
on-chip bootloader software.
 Digital peripherals:
 11 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors
and programmable open-drain mode.
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller







 GPIO pins can be used as edge and level sensitive interrupt sources.
 Four general purpose counter/timers with a total of one capture input and 10 match
outputs.
 Programmable windowed WatchDog Timer (WDT).
Analog peripherals:
 10-bit ADC with input multiplexing among five pins.
Serial interfaces:
 UART with fractional baud rate generation, internal FIFO, and RS-485 support.
 One SPI controller with SSP features and with FIFO and multi-protocol capabilities
(see Section 7.16).
Clock generation:
 12 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used
as a system clock.
 Programmable watchdog oscillator with a frequency range of 9.4 kHz to 2.3 MHz.
 PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. May be run from an external clock or the internal RC
oscillator.
 Clock output function with divider that can reflect the system oscillator clock, IRC
clock, CPU clock, and the Watchdog clock (LPC1104 only).
Power control:
 Integrated PMU (Power Management Unit) to minimize power consumption during
Sleep and Deep-sleep modes.
 Power profiles residing in boot ROM allowing to optimize performance and
minimize power consumption for any given application through one simple function
call.
 Two reduced power modes: Sleep and Deep-sleep modes.
 Processor wake-up from Deep-sleep mode via a dedicated start logic using up to
six of the functional pins.
 Power-On Reset (POR).
 Brownout detect with up to four separate thresholds for interrupt and forced reset.
Unique device serial number for identification.
Single 3.3 V power supply (1.8 V to 3.6 V).
Available as WLCSP16 package.
3. Applications
 Mobile devices
 Consumer peripherals
 Lighting
LPC1102_1104
Product data sheet
 8-/16-bit applications
 Portable devices
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
2 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC1102UK
WLCSP16
wafer level chip-size package; 16 bumps; 2.17  2.32  0.6 mm
-
LPC1104UK
WLCSP16
wafer level chip-size package; 16 bumps; 2.17  2.32  0.6 mm
-
4.1 Ordering options
Table 2.
LPC1102_1104
Product data sheet
Ordering options
Type number
Flash
Total
SRAM
UART
RS-485
SPI
ADC
channels
Package
LPC1102UK
32 kB
8 kB
1
1
5
WLCSP16
LPC1104UK
32 kB
8 kB
1
1
5
WLCSP16
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
3 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
5. Block diagram
XTALIN
SWD
RESET
LPC1102/1104
IRC
TEST/DEBUG
INTERFACE
CLOCK
GENERATION,
POWER CONTROL,
SYSTEM
FUNCTIONS
POR
ARM
CORTEX-M0
clocks and
controls
FLASH
32 kB
system bus
slave
GPIO port
PIO0/1
HIGH-SPEED
GPIO
CLKOUT(1)
SRAM
8 kB
slave
ROM
slave
slave
AHB-LITE BUS
slave
AHB TO APB
BRIDGE
RXD
TXD
UART
AD[4:0]
10-bit ADC
SCK0,
MISO0,
MOSI0
SPI
CT32B0_MAT[3,2(1),1,0]
CT32B1_MAT[2:0]
CT32B1_CAP0
CT16B0_MAT[2:0]
32-bit COUNTER/TIMER 0
WDT
32-bit COUNTER/TIMER 1
IOCONFIG
16-bit COUNTER/TIMER 0
16-bit COUNTER/TIMER 1
SYSTEM CONTROL
PMU
002aaf524
(1) LPC1104 only.
(2) CT32B0_MAT2 LPC1104 only.
Fig 1.
LPC1102/1104 block diagram
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
4 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
6. Pinning information
6.1 Pinning
LPC1102/1104UK
D
C
B
A
ball A1
index area
1
2
3
4
002aaf525
Fig 2.
LPC1102_1104
Product data sheet
Pin configuration WLCSP16 package
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
5 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
6.2 Pin description
Table 3.
LPC1102/1104 pin description table
Symbol
LPC1102 LPC1104 Start
logic
input
Type
Reset Description
state[1]
RESET/PIO0_0
C1[2]
B2[2]
I
I; PU
RESET — External reset input with 20 ns glitch
filter. A LOW -going pulse as short as 50 ns on this
pin resets the device, causing I/O ports and
peripherals to take on their default states, and
processor execution to begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin.
-
C1[3]
I/O
I; PU
PIO0_1 — General purpose digital input/output pin.
A LOW level on this pin during reset starts the ISP
command handler.
O
-
CLKOUT — Clockout pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
I/O
I;PU
PIO0_6 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
I/O
I; PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SPI.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
PIO0_1/CLKOUT/
yes
yes
CT32B0_MAT2
PIO0_6/SCK0
-
A1[3]
PIO0_8/MISO/
CT16B0_MAT0
A2[3]
A3[3]
PIO0_9/MOSI/
CT16B0_MAT1
A3[3]
SWCLK/
PIO0_10/
SCK0/CT16B0_MAT2
A4[3]
R/PIO0_11/
AD0/CT32B0_MAT3
R/PIO1_0/
AD1/CT32B1_CAP0
R/PIO1_1/
AD2/CT32B1_MAT0
LPC1102_1104
Product data sheet
B4[4]
B3[4]
C4[4]
A4[3]
A2[3]
B4[4]
B3[4]
C4[4]
yes
yes
yes
yes
yes
yes
no
I/O
I; PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SPI.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
I
I; PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output
pin.
I/O
-
SCK0 — Serial clock for SPI0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
-
I; PU
R — Reserved.
I/O
-
PIO0_11 — General purpose digital input/output
pin.
I
-
AD0 — A/D converter, input 0.
I
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
-
I; PU
R — Reserved.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer
1.
-
I; PU
R — Reserved.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
6 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC1102/1104 pin description table …continued
Symbol
LPC1102 LPC1104 Start
logic
input
Type
Reset Description
state[1]
R/PIO1_2/
AD3/CT32B1_MAT1
C3[4]
-
I; PU
R — Reserved.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I; PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I; PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O
-
TXD — Transmitter output for UART.
SWDIO/PIO1_3/AD4/
CT32B1_MAT2
PIO1_6/RXD/
CT32B0_MAT0
D4[4]
C2[3]
C3[4]
D4[4]
C2[3]
D1[3]
no
no
no
PIO1_7/TXD/
CT32B0_MAT1
D1[3]
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
VDD
D2; A1
D2
-
I
-
3.3 V supply voltage to the internal regulator, the
external rail, and the ADC. Also used as the ADC
reference voltage.
XTALIN
B2[5]
B1[5]
-
I
-
External clock input and input to internal clock
generator circuits. Input voltage must not exceed
1.8 V.
VSS
D3; B1
D3
-
I
-
Ground.
no
[1]
Pin state at reset for default function: I = Input; PU = internal pull-up enabled (pins pulled up to full VDD level (VDD = 3.3 V)).
[2]
5 V tolerant pad. See Figure 22 for the reset pad configuration.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 21).
[4]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see Figure 21).
[5]
When the external clock is not used, connect XTALIN as follows: XTALIN can be left floating or can be grounded (grounding is preferred
to reduce susceptibility to noise).
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
7 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7. Functional description
7.1 ARM Cortex-M0 processor
The ARM Cortex-M0 is a general purpose, 32-bit microprocessor, which offers high
performance and very low power consumption.
7.2 On-chip flash program memory
The LPC1102/1104 contain 32 kB of on-chip flash memory.
Remark: The LPC1102 supports In-Application Programming (IAP) and In-System
Programming (ISP). For ISP, since there is no dedicated ISP entry pin, user code is
required to invoke ISP functionality. Unprogrammed parts will automatically boot into ISP
mode.
7.3 On-chip SRAM
The LPC1102/1104 contain 8 kB on-chip static RAM memory.
7.4 Memory map
The LPC1102/1104 incorporate several distinct memory regions, shown in the following
figures. Figure 3 shows the overall map of the entire address space from the user
program viewpoint following reset. The interrupt vector area supports address remapping.
The AHB peripheral area is 2 MB in size, and is divided to allow for up to 128 peripherals.
The APB peripheral area is 512 kB in size and is divided to allow for up to 32 peripherals.
Each peripheral of either type is allocated 16 kB of space. This allows simplifying the
address decoding for each peripheral.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
8 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
AHB peripherals
LPC1102/1104
4 GB
0x5020 0000
0xFFFF FFFF
reserved
0xE010 0000
private peripheral bus
127 - 16 reserved
0xE000 0000
0x5004 0000
reserved
0x5020 0000
AHB peripherals
0x5000 0000
15-12
reserved
11-8
reserved
7-4
GPIO PIO1
3-0
GPIO PIO0
reserved
APB peripherals
0x5003 0000
0x5002 0000
0x5001 0000
0x5000 0000
0x4008 0000
31 - 23 reserved
0x4005 C000
0x4008 0000
APB peripherals
1 GB
reserved
22
0x4000 0000
0x4005 8000
21 - 19 reserved
0x4004 C000
reserved
0x2000 0000
0.5 GB
18
system control
17
IOCONFIG
16
15
SPI
flash controller
14
PMU
reserved
0x1000 2000
0x1000 0000
reserved
0x0000 8000
32 kB on-chip flash
0 GB
0x4004 0000
0x4003 C000
0x4003 8000
0x4002 8000
0x1FFF 0000
reserved
8 kB SRAM
0x4004 4000
13 - 10 reserved
0x1FFF 4000
16 kB boot ROM
0x4004 8000
9
reserved
8
reserved
0x4002 0000
7
ADC
0x4001 C000
6
32-bit counter/timer 1
0x4001 8000
5
32-bit counter/timer 0
0x4001 4000
4
16-bit counter/timer 1
0x4001 0000
3
16-bit counter/timer 0
0x4000 C000
2
UART
0x4000 8000
1
0
WDT
0x4000 4000
reserved
0x4000 0000
0x4002 4000
0x0000 00C0
active interrupt vectors
0x0000 0000
0x0000 0000
002aaf526
Fig 3.
LPC1102/1104 memory map
7.5 Nested Vectored Interrupt Controller (NVIC)
The Nested Vectored Interrupt Controller (NVIC) is an integral part of the Cortex-M0. The
tight coupling to the CPU allows for low interrupt latency and efficient processing of late
arriving interrupts.
7.5.1 Features
• Controls system exceptions and peripheral interrupts.
• In the LPC1102/1104, the NVIC supports 19 vectored interrupts including up to 6
inputs to the start logic from individual GPIO pins.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
9 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• Four programmable interrupt priority levels, with hardware priority level masking.
• Software interrupt generation.
7.5.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of up to 11 pins) regardless of the selected function, can be
programmed to generate an interrupt on a level, or rising edge or falling edge, or both.
7.6 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.7 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
The LPC1102/1104 use accelerated GPIO functions:
• GPIO registers are a dedicated AHB peripheral so that the fastest possible I/O timing
can be achieved.
• Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of 11 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
7.7.1 Features
• Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
• Direction control of individual bits.
• All I/O default to inputs with pull-ups enabled after reset.
• Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin.
• All GPIO pins are pulled up to 3.3 V (VDD = 3.3 V) if their pull-up resistor is enabled in
the IOCONFIG block.
• Programmable open-drain mode.
7.8 UART
The LPC1102/1104 contain one UART.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
10 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Support for RS-485/9-bit mode allows both software address detection and automatic
address detection using 9-bit mode.
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
7.8.1 Features
•
•
•
•
•
Maximum UART data bit rate of 3.125 Mbit/s.
16 Byte Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• FIFO control mechanism that enables software flow control implementation.
• Support for RS-485/9-bit mode.
7.9 SPI serial I/O controller
The LPC1102/1104 contain one SPI controller and fully supports SSP features.
The SPI controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SPI supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
Remark: Care must be taken when using the SPI because the SPI clock SCK and the
serial wire debug clock SWCLK share the same pin on the WLCSP16 package. Once the
SPI is enabled, the serial wire debugger is no longer available (LPC1102 only).
7.9.1 Features
• Maximum SPI speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
• Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
7.10 10-bit ADC
The LPC1102/1104 contain one ADC. It is a single 10-bit successive approximation ADC
with five channels.
7.10.1 Features
• 10-bit successive approximation ADC.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
11 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
•
•
•
•
•
•
•
Input multiplexing among 5 pins.
Power-down mode.
Measurement range 0 V to VDD.
10-bit conversion time  2.44 s (up to 400 kSamples/s).
Burst conversion mode for single or multiple inputs.
Optional conversion on transition of input pin or timer match signal.
Individual result registers for each ADC channel to reduce interrupt overhead.
7.11 General purpose external event counter/timers
The LPC1102/1104 include two 32-bit counter/timers and two 16-bit counter/timers. The
counter/timer is designed to count cycles of the system derived clock. It can optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. Each counter/timer also includes one capture input to trap the timer value
when an input signal transitions, optionally generating an interrupt.
7.11.1 Features
• A 32-bit/16-bit timer/counter with a programmable 32-bit/16-bit prescaler.
• Counter or timer operation.
• One capture channel that can take a snapshot of the timer value when an input signal
transitions. A capture event may also generate an interrupt.
• Four match registers per timer that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
7.12 System tick timer
The ARM Cortex-M0 includes a system tick timer (SYSTICK) that is intended to generate
a dedicated SYSTICK exception at a fixed time interval (typically 10 ms).
7.13 Windowed WatchDog Timer
The purpose of the watchdog is to reset the controller if software fails to periodically
service it within a programmable time window.
7.13.1 Features
• Internally resets chip if not periodically reloaded during the programmable time-out
period.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
12 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• Optional windowed operation requires reload to occur between a minimum and
maximum time period, both programmable.
• Optional warning interrupt can be generated at a programmable time prior to
watchdog time-out.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect feed sequence causes reset or interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 24-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK)  256  4) to (Tcy(WDCLK)  224  4) in
multiples of Tcy(WDCLK)  4.
• The Watchdog Clock (WDCLK) source can be selected from the IRC or the dedicated
watchdog oscillator (WDO). This gives a wide range of potential timing choices of
watchdog operation under different power conditions.
7.14 Clocking and power control
7.14.1 Crystal oscillators
The LPC1102/1104 include two independent oscillators. These are the Internal RC
oscillator (IRC) and the Watchdog oscillator. Each oscillator can be used for more than
one purpose as required in a particular application.
Following reset, the LPC1102/1104 operate from the Internal RC oscillator until switched
by software. This allows systems to operate without any external crystal and the
bootloader code to operate at a known frequency.
See Figure 4 for an overview of the LPC1102/1104 clock generation.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
13 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
SYSTEM CLOCK
DIVIDER
AHB clock 0
(system)
system clock
18
AHB clocks 1 to 18
(memories
and peripherals)
AHBCLKCTRL[1:18]
(AHB clock enable)
IRC oscillator
SPI0 PERIPHERAL
CLOCK DIVIDER
SPI0
UART PERIPHERAL
CLOCK DIVIDER
UART
WDT CLOCK
DIVIDER
WDT
main clock
watchdog oscillator
MAINCLKSEL
(main clock select)
IRC oscillator
IRC oscillator
watchdog oscillator
SYSTEM PLL
external clock
WDTUEN
(WDT clock update enable)
SYSPLLCLKSEL
(system PLL clock select)
IRC oscillator
system oscillator
watchdog oscillator
CLKOUT PIN CLOCK
DIVIDER
CLKOUT pin
CLKOUTUEN
(CLKOUT update enable)
002aaf527
Fig 4.
LPC1102/1104 clock generation block diagram
7.14.1.1
Internal RC oscillator
The IRC may be used as the clock source for the WDT, and/or as the clock that drives the
PLL and subsequently the CPU. The nominal IRC frequency is 12 MHz. The IRC is
trimmed to 1 % accuracy over the entire voltage and temperature range.
Upon power-up or any chip reset, the LPC1102/1104 use the IRC as the clock source.
Software may later switch to one of the other available clock sources.
7.14.1.2
Watchdog oscillator
The watchdog oscillator can be used as a clock source that directly drives the CPU or the
watchdog timer. The watchdog oscillator nominal frequency is programmable between
9.4 kHz to 2.3 MHz. The frequency spread over processing and temperature is 40 %.
7.14.2 System PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
14 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
its frequency range while the PLL is providing the desired output frequency. The PLL
output frequency must be lower than 100 MHz. The output divider may be set to divide by
2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to lock, and then connect to the PLL as a clock source.
The PLL settling time is 100 s.
7.14.3 Clock output (LPC1104 only)
The LPC1104 features a clock output function that routes the IRC oscillator, the system
oscillator, the watchdog oscillator, or the main clock to an output pin.
7.14.4 Wake-up process
The LPC1102/1104 begin operation at power-up by using the 12 MHz IRC oscillator as the
clock source. This allows chip operation to resume quickly. If an external clock or the PLL
is needed by the application, software will need to enable these features and wait for them
to stabilize before they are used as a clock source.
7.14.5 Power control
The LPC1102/1104 support a variety of power control features. There are two special
modes of processor power reduction: Sleep mode and Deep-sleep mode. The CPU clock
rate may also be controlled as needed by changing clock sources, reconfiguring PLL
values, and/or altering the CPU clock divider value. This allows a trade-off of power
versus processing speed based on application requirements. In addition, a register is
provided for shutting down the clocks to individual on-chip peripherals, allowing fine tuning
of power consumption by eliminating all dynamic power use in any peripherals that are not
required for the application. Selected peripherals have their own clock divider which
provides even better power control.
7.14.5.1
Power profiles
The power consumption in Active and Sleep modes can be optimized for the application
through a simple call to the power profiles. The power configuration routine configures the
LPC1102/1104 for one of the following power modes:
• Default mode corresponding to power configuration after reset.
• CPU performance mode corresponding to optimized processing capability.
• Efficiency mode corresponding to optimized balance of current consumption and CPU
performance.
• Low-current mode corresponding to lowest power consumption.
In addition, the power profiles includes a routine to select the optimal PLL settings for a
given system clock and PLL input clock.
7.14.5.2
Sleep mode
When Sleep mode is entered, the clock to the core is stopped. Resumption from the Sleep
mode does not need any special sequence but re-enabling the clock to the ARM core.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
15 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
In Sleep mode, execution of instructions is suspended until either a reset or interrupt
occurs. Peripheral functions continue operation during Sleep mode and may generate
interrupts to cause the processor to resume execution. Sleep mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
7.14.5.3
Deep-sleep mode
In Deep-sleep mode, the chip is in Sleep mode, and in addition all analog blocks are shut
down except for the watchdog oscillator and the BOD circuit, which can be configured to
remain running in Deep-sleep mode to allow a reset initiated by a timer or BOD event.
Deep-sleep mode allows for additional power savings.
Six of the GPIO pins (see Table 3) serve as external wake-up pins to a dedicated start
logic to wake up the chip from Deep-sleep mode.
The clock source should be switched to IRC before entering Deep-sleep mode unless the
watchdog oscillator remains running in Deep-sleep mode. The IRC can be switched on
and off glitch-free and provides a clean clock signal after start-up.
7.15 System control
7.15.1 Start logic
The start logic connects external pins to corresponding interrupts in the NVIC. Each pin
shown in Table 3 as input to the start logic has an individual interrupt in the NVIC interrupt
vector table. The start logic pins can serve as external interrupt pins when the chip is
running. In addition, an input signal on the start logic pins can wake up the chip from
Deep-sleep mode when all clocks are shut down.
The start logic must be configured in the system configuration block and in the NVIC
before being used.
7.15.2 Reset
Reset has four sources on the LPC1102/1104: the RESET pin, the Watchdog reset,
Power-On Reset (POR), and the BrownOut Detection (BOD) circuit. In addition, there is
an ARM software reset. The RESET pin is a Schmitt trigger input pin. Assertion of chip
reset by any source, once the operating voltage attains a usable level, starts the IRC and
initializes the flash controller.
A LOW-going pulse as short as 50 ns resets the part.
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the boot block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values.
7.15.3 Brownout detection
The LPC1102/1104 include up to four levels for monitoring the voltage on the VDD pin. If
this voltage falls below one of the three selected levels, the BOD asserts an interrupt
signal to the NVIC. This signal can be enabled for interrupt in the Interrupt Enable
Register in the NVIC in order to cause a CPU interrupt; if not, software can monitor the
signal by reading a dedicated status register. Four additional threshold levels can be
selected to cause a forced reset of the chip.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
16 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.15.4 Code security (Code Read Protection - CRP)
This feature of the LPC1102/1104 allow user to enable different levels of security in the
system so that access to the on-chip flash and use of the Serial Wire Debugger (SWD)
can be restricted. When needed, CRP is invoked by programming a specific pattern into a
dedicated flash location. IAP commands are not affected by the CRP.
There are three levels of Code Read Protection:
1. CRP1 disables access to the chip via the SWD and allows partial flash update
(excluding flash sector 0). This mode is useful when CRP is required and flash field
updates are needed but all sectors can not be erased.
2. CRP2 disables access to the chip via the SWD and only allows full flash erase and
update.
3. Running an application with level CRP3 selected fully disables any access to the chip
via the SWD pins.
Remark: The LPC1102 does not provide an ISP entry pin to be monitored at reset. For all
three CRP levels, the user’s application code must provide a flash update mechanism
which reinvokes ISP by defining a user-selected PIOn pin for ISP entry.
CAUTION
If Code Read Protection of any level (CRP1, CRP2 or CRP3) is selected, no future factory
testing can be performed on the device.
7.15.5 APB interface
The APB peripherals are located on one APB bus.
7.15.6 AHBLite
The AHBLite connects the CPU bus of the ARM Cortex-M0 to the flash memory, the main
static RAM, and the Boot ROM.
7.15.7 External interrupt inputs
All GPIO pins can be level or edge sensitive interrupt inputs. In addition, start logic inputs
serve as external interrupts (see Section 7.15.1).
7.16 Emulation and debugging
Debug functions are integrated into the ARM Cortex-M0. Serial wire debug with four
breakpoints and two watchpoints is supported.
Remark: Care must be taken when using the SPI because the SPI clock SCK and the
serial wire debug clock SWCLK share the same pin on the WLCSP16 package. Once the
SPI is enabled, the serial wire debugger is no longer available (LPC1102 only).
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
17 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
8. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
Min
Max
Unit
[2]
0.5
+4.6
V
[2][3]
0.5
+5.5
V
0.5
+3.6
V
0.5
+4.6
V
100
mA
supply voltage (core and external rail)
VDD
input voltage
VI
5 V tolerant I/O
pins; VDD  1.8 V
VDD = 0 V
[2][4]
VIA
analog input voltage
pin configured as
analog input
IDD
supply current
per supply pin
[5]
-
[5]
-
100
mA
-
100
mA
65
+150
C
-
150
C
-
1.5
W
6500
V
ISS
ground current
per ground pin
Ilatch
I/O latch-up current
(0.5VDD) < VI <
(1.5VDD);
Tstg
storage temperature
non-operating
Tj(max)
maximum junction temperature
Ptot(pack)
total power dissipation (per package)
based on package
heat transfer, not
device power
consumption
VESD
electrostatic discharge voltage
human body
model; all pins
Tj < 125 C
[1]
[6]
[7]
The following applies to the limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
c) The limiting values are stress ratings only. Operating the part at these values is not recommended and proper operation is not
guaranteed. The conditions for functional operation are specified in Table 5.
[2]
Maximum/minimum voltage above the maximum operating voltage (see Table 5) and below ground that can be applied for a short time
(< 10 ms) to a device without leading to irrecoverable failure. Failure includes the loss of reliability and shorter lifetime of the device.
[3]
Including voltage on outputs in 3-state mode.
[4]
See Table 6 for maximum operating voltage.
[5]
The peak current is limited to 25 times the corresponding maximum current.
[6]
The maximum non-operating storage temperature is different than the temperature for required shelf life which should be determined
based on required shelf lifetime. Please refer to the JEDEC spec (J-STD-033B.1) for further details.
[7]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
18 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9. Static characteristics
Table 5.
Static characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
VDD
supply voltage (core
and external rail)
IDD
supply current
Conditions
Min
Typ[1]
Max
Unit
1.8
3.3
3.6
V
-
2
-
mA
-
7
-
mA
-
1
-
mA
-
2
-
A
Active mode; code
while(1){}
executed from flash
system clock = 12 MHz
VDD = 3.3 V
system clock = 50 MHz
VDD = 3.3 V
Sleep mode;
system clock = 12 MHz
[2][3][4]
[5][6]
[2][3][5]
[6][7]
[2][3][4]
[5][6]
VDD = 3.3 V
Deep-sleep mode;
VDD = 3.3 V
[2][3][8]
Standard port pins, RESET
IIL
LOW-level input current VI = 0 V; on-chip pull-up
resistor disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip
pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD;
on-chip pull-up/down
resistors disabled
-
0.5
10
nA
VI
input voltage
pin configured to provide
a digital function;
0
-
5.0
V
[9]
VDD  1.8 V; 5 V
tolerant pins
VDD = 0 V
0
-
3.6
V
output active
0
-
VDD
V
0.7VDD
-
-
V
VO
output voltage
VIH
HIGH-level input
voltage
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
-
0.4
-
V
VOH
HIGH-level output
voltage
2.5 V  VDD  3.6 V;
IOH = 4 mA
VDD  0.4
-
-
V
1.8 V  VDD < 2.5 V;
IOH = 3 mA
VDD  0.4
-
-
V
2.5 V  VDD  3.6 V;
IOL = 4 mA
-
-
0.4
V
1.8 V  VDD < 2.5 V;
IOL = 3 mA
-
-
0.4
V
VOL
LPC1102_1104
Product data sheet
LOW-level output
voltage
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
19 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 5.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
IOH
HIGH-level output
current
VOH = VDD  0.4 V;
4
-
-
mA
3
-
-
mA
4
-
-
mA
2.5 V  VDD  3.6 V
1.8 V  VDD < 2.5 V
LOW-level output
current
IOL
VOL = 0.4 V
2.5 V  VDD  3.6 V
1.8 V  VDD < 2.5 V
3
-
-
mA
-
-
45
mA
-
-
50
mA
IOHS
HIGH-level short-circuit VOH = 0 V
output current
[11]
IOLS
LOW-level short-circuit
output current
VOL = VDD
[11]
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V;
15
50
85
A
10
50
85
A
0
0
0
A
0.5
1.8
1.95
V
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
VDD < VI < 5 V
External clock input
Vi(xtal)
crystal input voltage
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
[2]
Tamb = 25 C.
[3]
IDD measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
[4]
IRC enabled; external clock disabled; system PLL disabled.
[5]
BOD disabled.
[6]
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to UART and SPI0/1 disabled in system configuration
block. Low-current mode PWR_LOW_CURRENT selected when running the set_power routine in the power profiles.
[7]
IRC disabled; system oscillator enabled; system PLL enabled.
[8]
All oscillators and analog blocks turned off in the PDSLEEPCFG register; PDSLEEPCFG = 0x0000 18FF. Before entering deep-sleep
mode, you must write a 0 to bit 4 and bit 5 of the GPIO0DATA register at location 0x5000 3FFC and a 1 to bit 4 and bit 5 of the
GPIO0DIR register at location 0x5000 8000.
[9]
Including voltage on outputs in 3-state mode.
[10] VDD supply voltage must be present.
[11] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
20 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 6.
ADC static characteristics
Tamb = 40 C to +85 C unless otherwise specified; ADC frequency 4.5 MHz, VDD = 2.5 V to 3.6 V.
Symbol
Parameter
VIA
analog input voltage
0
-
VDD
V
Cia
analog input capacitance
-
-
1
pF
ED
differential linearity error
[1][2]
-
-
1
LSB
integral non-linearity
[3]
-
-
1.5
LSB
EO
offset error
[4]
-
-
3.5
LSB
EG
gain error
[5]
-
-
0.6
%
ET
absolute error
[6]
-
-
4
LSB
Rvsi
voltage source interface
resistance
-
-
40
k
Ri
input resistance
-
-
2.5
M
EL(adj)
Conditions
Min
[7][8]
Typ
Max
Unit
[1]
The ADC is monotonic, there are no missing codes.
[2]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 5.
[3]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 5.
[4]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 5.
[5]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 5.
[6]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated
ADC and the ideal transfer curve. See Figure 5.
[7]
Tamb = 25 C; maximum sampling frequency fs = 400 kSamples/s and analog input capacitance Cia = 1 pF.
[8]
Input resistance Ri depends on the sampling frequency fs: Ri = 1 / (fs  Cia).
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
21 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
offset
error
EO
gain
error
EG
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
1018
1019
1020
1021
1022
1023
1024
VIA (LSBideal)
offset error
EO
1 LSB =
VDD − VSS
1024
002aaf426
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 5.
ADC characteristics
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
22 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.1 BOD static characteristics
Table 7.
BOD static characteristics[1]
Tamb = 25 C.
Symbol
Parameter
Conditions
Vth
threshold voltage
interrupt level 1
Min
Typ
Max
Unit
assertion
-
2.22
-
V
de-assertion
-
2.35
-
V
assertion
-
2.52
-
V
de-assertion
-
2.66
-
V
assertion
-
2.80
-
V
de-assertion
-
2.90
-
V
assertion
-
1.46
-
V
de-assertion
-
1.63
-
V
interrupt level 2
interrupt level 3
reset level 0
reset level 1
assertion
-
2.06
-
V
de-assertion
-
2.15
-
V
assertion
-
2.35
-
V
de-assertion
-
2.43
-
V
assertion
-
2.63
-
V
de-assertion
-
2.71
-
V
reset level 2
reset level 3
[1]
Interrupt levels are selected by writing the level value to the BOD control register BODCTRL, see User
manual UM10429.
9.2 Power consumption
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions (see user manual UM10429):
• All digital pins configured as GPIO with pull-up resistor disabled in the IOCONFIG
block.
• GPIO pins configured as outputs using the GPIOnDIR registers.
• Write 0 to all GPIOnDATA registers to drive the outputs LOW.
• Write a 1 to bit 4 and bit 5 of the GPIO0DIR register at location 0x5000 8000 and a 0
to bit 4 and bit 5 of the GPIO0DATA register at location 0x5000 3FFC. This ensures
that not-bonded out pins are in a well-defined state.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
23 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf980
10
IDD
(mA)
8
48 MHz(2)
6
36 MHz(2)
4
24 MHz(2)
12 MHz(1)
2
0
1.8
2.4
3.0
3.6
VDD (V)
Conditions: Tamb = 25 C; active mode entered executing code while(1){} from flash; all
peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL= 0x1F); all peripheral
clocks disabled; internal pull-up resistors disabled; BOD disabled; low-current mode.
(1) System PLL disabled; IRC enabled.
(2) System PLL enabled; IRC disabled.
Fig 6.
Active mode: Typical supply current IDD versus supply voltage VDD for different
system clock frequencies
002aaf981
10
IDD
(mA)
8
48 MHz(2)
6
36 MHz(2)
4
24 MHz(2)
12 MHz(1)
2
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; active mode entered executing code while(1){} from flash; all
peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL= 0x1F); all peripheral
clocks disabled; internal pull-up resistors disabled; BOD disabled; low-current mode.
(1) System PLL disabled; IRC enabled.
(2) System PLL enabled; IRC disabled.
Fig 7.
LPC1102_1104
Product data sheet
Active mode: Typical supply current IDD versus temperature for different system
clock frequencies
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
24 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf982
6
IDD
(mA)
48 MHz(2)
4
36 MHz(2)
24 MHz(2)
2
12 MHz(1)
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; sleep mode entered from flash; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL= 0x1F); all peripheral clocks disabled; internal
pull-up resistors disabled; BOD disabled; low-current mode.
(1) System PLL disabled; IRC enabled.
(2) System PLL enabled; IRC disabled.
Fig 8.
Sleep mode: Typical supply current IDD versus temperature for different system
clock frequencies
002aaf977
5.5
IDD
(μA)
4.5
3.5
VDD = 3.3 V, 3.6 V
1.8 V
2.5
1.5
−40
−15
10
35
60
85
temperature (°C)
Conditions: BOD disabled; all oscillators and analog blocks disabled in the PDSLEEPCFG register
(PDSLEEPCFG = 0x0000 18FF).
Remark: Before entering deep-sleep mode, you must write a 0 to bit 4 and bit 5 of the GPIO0DATA
register at location 0x5000 3FFC and a 1 to bit 4 and bit 5 of the GPIO0DIR register at location
0x5000 8000.
Fig 9.
LPC1102_1104
Product data sheet
Deep-sleep mode: Typical supply current IDD versus temperature for different
supply voltages VDD
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
25 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.3 CoreMark data
002aah163
14
IDD
(mA)
11.2
mode 0
mode 1
mode 2
mode 3
8.4
5.6
2.8
0
0
10
20
30
40
50
frequency (MHz)
External signal generator providing 1 MHz to 20 MHz signal drives the XTALIN input; when testing
1 MHz to 19 MHz the system PLL is OFF, SYSAHBCLKDIV = 1; when testing 20 MHz to 50 MHz
the system PLL is configured so that SYSAHBCLKDIV = 1.
Fig 10. CoreMark current consumption for power modes 0, 1, 2, and 3
9.4 Electrical pin characteristics
002aae991
15
IOL
(mA)
T = 85 °C
25 °C
−40 °C
10
5
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 11. Typical LOW-level output current IOL versus LOW-level output voltage VOL
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
26 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aae992
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
8
16
24
IOH (mA)
Conditions: VDD = 3.3 V; standard port pins.
Fig 12. Typical HIGH-level output voltage VOH versus HIGH-level output source current
IOH
002aae988
10
Ipu
(μA)
−10
−30
T = 85 °C
25 °C
−40 °C
−50
−70
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 13. Typical pull-up current Ipu versus input voltage VI
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
27 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aae989
80
T = 85 °C
25 °C
−40 °C
Ipd
(μA)
60
40
20
0
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 14. Typical pull-down current Ipd versus input voltage VI
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
28 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10. Dynamic characteristics
10.1 Power-up ramp conditions
Table 8.
Power-up characteristics
Tamb = 40 C to +85 C.
Symbol Parameter
Conditions
Min
at t = t1: 0 < VI 400 mV
tr
rise time
twait
wait time
VI
input voltage
[1]
[1][2]
at t = t1 on pin VDD
Typ
Max
Unit
0
-
500
ms
12
-
-
s
0
-
400
mV
[1]
See Figure 15.
[2]
The wait time specifies the time the power supply must be at levels below 400 mV before ramping up.
tr
VDD
400 mV
0
twait
t = t1
002aag001
Condition: 0 < VI 400 mV at start of power-up (t = t1)
Fig 15. Power-up ramp
10.2 Flash memory
Table 9.
Flash characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
LPC1102_1104
Product data sheet
Parameter
Nendu
endurance
tret
retention time
ter
erase time
tprog
programming
time
Conditions
Min
[1]
Typ
Max
Unit
10000
100 000
-
cycles
powered
10
-
-
years
unpowered
20
-
-
years
sector or multiple
consecutive
sectors
95
100
105
ms
0.95
1
1.05
ms
[2]
[1]
Number of program/erase cycles.
[2]
Programming times are given for writing 256 bytes from RAM to the flash. Data must be written to the flash
in blocks of 256 bytes.
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
29 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.3 External clock
Table 10. Dynamic characteristic: external clock
Tamb = 40 C to +85 C; VDD over specified ranges.[1]
Min
Typ[2]
Max
Unit
oscillator frequency
1
-
25
MHz
Tcy(clk)
clock cycle time
40
-
1000
ns
tCHCX
clock HIGH time
Tcy(clk)  0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk)  0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
Symbol
Parameter
fosc
Conditions
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 16. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
30 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.4 Internal oscillators
Table 11. Dynamic characteristic: internal oscillators
Tamb = 40 C to +85 C; 2.7 V  VDD  3.6 V.[1]
Symbol
Parameter
Conditions
fosc(RC)
internal RC oscillator frequency -
Min
Typ[2]
Max
Unit
11.88
12
12.12
MHz
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
002aaf403
12.15
f
(MHz)
VDD = 3.6 V
3.3 V
3.0 V
2.7 V
2.4 V
2.0 V
12.05
11.95
11.85
−40
−15
10
35
60
85
temperature (°C)
Conditions: Frequency values are typical values. 12 MHz  1 % accuracy is guaranteed for
2.7 V  VDD  3.6 V and Tamb = 40 C to +85 C. Variations between parts may cause the IRC to
fall outside the 12 MHz  1 % accuracy specification for voltages below 2.7 V.
Fig 17. Internal RC oscillator frequency versus temperature
Table 12.
Dynamic characteristics: Watchdog oscillator
Min
Typ[1]
Max
Unit
internal oscillator DIVSEL = 0x1F, FREQSEL = 0x1
frequency
in the WDTOSCCTRL register;
[2][3]
-
9.4
-
kHz
DIVSEL = 0x00, FREQSEL = 0xF
in the WDTOSCCTRL register
[2][3]
-
2300
-
kHz
Symbol Parameter
fosc(int)
LPC1102_1104
Product data sheet
Conditions
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
[2]
The typical frequency spread over processing and temperature (Tamb = 40 C to +85 C) is 40 %.
[3]
See user manual UM10429.
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
31 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.5 I/O pins
Table 13. Dynamic characteristic: I/O pins[1]
Tamb = 40 C to +85 C; 3.0 V  VDD  3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
pin
configured as
output
3.0
-
5.0
ns
tf
fall time
pin
configured as
output
2.5
-
5.0
ns
[1]
Applies to standard port pins and RESET pin.
10.6 SPI interfaces
Table 14.
Dynamic characteristics of SPI pins in SPI mode
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
-
-
ns
SPI master (in SPI mode)
when only receiving
[1]
50
when only transmitting
[1]
40
in SPI mode
[2]
15
2.0 V  VDD < 2.4 V
[2]
20
1.8 V  VDD < 2.0 V
[2]
24
-
-
ns
in SPI mode
[2]
0
-
-
ns
tv(Q)
data output valid time in SPI mode
[2]
-
-
10
ns
th(Q)
data output hold time in SPI mode
[2]
0
-
-
ns
Tcy(clk)
clock cycle time
data set-up time
tDS
ns
-
-
ns
2.4 V  VDD  3.6 V
data hold time
tDH
ns
SPI slave (in SPI mode)
Tcy(PCLK)
PCLK cycle time
20
-
-
ns
tDS
data set-up time
in SPI mode
[3][4]
0
-
-
ns
tDH
data hold time
in SPI mode
[3][4]
3  Tcy(PCLK) + 4
-
-
ns
data output valid time in SPI mode
[3][4]
-
-
3  Tcy(PCLK) + 11
ns
data output hold time in SPI mode
[3][4]
-
-
2  Tcy(PCLK) + 5
ns
tv(Q)
th(Q)
[1]
Tcy(clk) = (SSPCLKDIV  (1 + SCR)  CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the
main clock frequency fmain, the SPI peripheral clock divider (SSPCLKDIV), the SPI SCR parameter (specified in the SSP0CR0 register),
and the SPI CPSDVSR parameter (specified in the SPI clock prescale register).
[2]
Tamb = 40 C to 85 C.
[3]
Tcy(clk) = 12  Tcy(PCLK).
[4]
Tamb = 25 C; for normal voltage supply range: VDD = 3.3 V.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
32 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Tcy(clk)
SCK (CPOL = 0)
SCK (CPOL = 1)
tv(Q)
th(Q)
DATA VALID
MOSI
DATA VALID
tDS
DATA VALID
MISO
tDH
DATA VALID
tv(Q)
MOSI
DATA VALID
th(Q)
DATA VALID
tDH
tDS
MISO
DATA VALID
CPHA = 1
CPHA = 0
DATA VALID
002aae829
Fig 18. SPI master timing in SPI mode
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
33 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Tcy(clk)
SCK (CPOL = 0)
SCK (CPOL = 1)
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
th(Q)
DATA VALID
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
DATA VALID
CPHA = 1
DATA VALID
th(Q)
CPHA = 0
DATA VALID
002aae830
Fig 19. SPI slave timing in SPI mode
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
34 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11. Application information
11.1 ADC usage notes
The following guidelines show how to increase the performance of the ADC in a noisy
environment beyond the ADC specifications listed in Table 6:
• The ADC input trace must be short and as close as possible to the LPC1102/1104
chip.
• The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
• Because the ADC and the digital core share the same power supply, the power supply
line must be adequately filtered.
• To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
11.2 XTAL input
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
Ci = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave
mode, a minimum of 200 mV (RMS) is needed.
LPC1xxx
XTALIN
Ci
100 pF
Cg
002aae788
Fig 20. Slave mode operation of the on-chip oscillator
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(Figure 20), with an amplitude between 200 mV (RMS) and 1000 mV (RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
11.3 Standard I/O pad configuration
Figure 21 shows the possible pin modes for standard I/O pins with analog input function:
•
•
•
•
•
LPC1102_1104
Product data sheet
Digital output driver
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Analog input
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
35 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
VDD
VDD
open-drain enable
pin configured
as digital output
driver
strong
pull-up
output enable
ESD
data output
PIN
strong
pull-down
ESD
VSS
VDD
weak
pull-up
pull-up enable
weak
pull-down
repeater mode
enable
pin configured
as digital input
pull-down enable
data input
select analog input
pin configured
as analog input
analog input
002aah159
Fig 21. Standard I/O pad configuration
11.4 Reset pad configuration
VDD
VDD
VDD
Rpu
reset
ESD
20 ns RC
GLITCH FILTER
PIN
ESD
VSS
002aaf274
Fig 22. Reset pad configuration
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
36 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11.5 ADC effective input impedance
A simplified diagram of the ADC input channels can be used to determine the effective
input impedance seen from an external voltage source. See Figure 23.
ADC Block
Source
ADC
COMPARATOR
Rmux
Rsw
<2 kΩ
<1.3 kΩ
Cia
Rs
Rin
Cio
VEXT
VSS
002aah615
Fig 23. ADC input channel
The effective input impedance, Rin, seen by the external voltage source, VEXT, is the
parallel impedance of ((1/fs x Cia) + Rmux + Rsw) and (1/fs x Cio), and can be calculated
using Equation 1 with
fs = sampling frequency
Cia = ADC analog input capacitance
Rmux = analog mux resistance
Rsw = switch resistance
Cio = pin capacitance
1
1
R in =  ------------------ + R mux + R sw   ------------------
 f s  C ia
  f s  C io
(1)
Under nominal operating condition VDD = 3.3 V and with the maximum sampling
frequency fs = 400 kHz, the parameters assume the following values:
Cia = 1 pF (max)
Rmux = 2 kΩ (max)
Rsw = 1.3 kΩ (max)
Cio = 7.1 pF (max)
The effective input impedance with these parameters is Rin = 308 kΩ.
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
37 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
12. Package outline
WLCSP16: wafer level chip-size package; 16 bumps; body 2.17 x 2.32 x 0.6 mm
A
B
D
LPC1102UK
ball A1
index area
A2
E
A
A1
detail X
e1
1/2 e
e
∅v
∅w
b
C
C A B
C
y
D
e
C
1/2 e
e2
B
A
ball A1
index area
1
2
3
4
X
0
1
Dimensions
Unit
mm
2 mm
scale
A
A1
A2
b
D
E
max 0.65 0.27 0.38 0.35 2.21 2.36
nom 0.60 0.24 0.36 0.32 2.17 2.32
min 0.55 0.21 0.34 0.29 2.13 2.28
e
e1
e2
0.5
1.5
1.5
v
w
y
0.15 0.05 0.05
lpc1102uk_po
References
Outline
version
IEC
JEDEC
JEITA
LPC1102UK
---
---
---
European
projection
Issue date
10-10-15
10-10-18
Fig 24. Package outline LPC1102UK (WLCSP16)
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
38 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
13. Abbreviations
Table 15.
LPC1102_1104
Product data sheet
Abbreviations
Acronym
Description
ADC
Analog-to-Digital Converter
AHB
Advanced High-performance Bus
APB
Advanced Peripheral Bus
BOD
BrownOut Detection
GPIO
General Purpose Input/Output
PLL
Phase-Locked Loop
RC
Resistor-Capacitor
SPI
Serial Peripheral Interface
SSI
Serial Synchronous Interface
SSP
Synchronous Serial Port
UART
Universal Asynchronous Receiver/Transmitter
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
39 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
14. Revision history
Table 16.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
LPC1102_1104 v.7
20130926
Product data sheet
-
LPC1102_1104 v.6
Modifications:
LPC1102_1104 v.6
Modifications:
LPC1102_1104 v.5
Modifications:
LPC1102 v.4
Modifications:
LPC1102 v.3
Modifications:
LPC1102 v.2
Modifications:
LPC1102 v.1
LPC1102_1104
Product data sheet
•
•
•
Parameter VI updated in Table 4 and Table 5. Condition VDD = 0 added.
Section 11.5 “ADC effective input impedance” added.
Removed tclk(H) and tclk(L) from Figure 18 “SPI master timing in SPI mode” and Figure
19 “SPI slave timing in SPI mode”; spec not characterized.
20121231
Product data sheet
-
•
•
Added Section 9.3 “CoreMark data”.
•
•
Table 4 “Limiting values” expanded for clarity.
LPC1102_1104 v.5
Conditions for power consumption in Deep-sleep mode updated in Table 5, Table
note 8 and Section 9.2.
BOD reset level 0 added in Table 7.
20120727
Product data sheet
-
LPC1102 v.4
•
•
Added LPC1104UK.
•
For parameters IOL, VOL, IOH, VOH, changed conditions to 1.8 V  VDD < 2.5 V and 2.5
V  VDD  3.6 V in Table 5).
•
•
WDOSc frequency range corrected.
Removed footnote “The peak current is limited to 25 times the corresponding
maximum current.” from Table 4.
BOD level 0 removed in Table 7.
20110624
•
•
•
•
•
•
•
Product data sheet
-
ADC sampling frequency corrected in Table 6 (Table note 7).
Parameter Tcy(clk) corrected on Table 14.
Windowed WDT features added (Section 7.13).
Programmable open-drain mode added to GPIO pins (Section 7.7).
Pull-up level specified in Table 3, Table note 1 and Section 7.7.
Condition for parameter Tstg in Table 4 updated.
Table note 4 of Table 4 updated.
20110418
Product data sheet
-
•
•
•
•
•
Changed data sheet status to Product.
•
Clock output removed from feature list.
LPC1102 v.2
Power consumption data added (see Figure 6 to Figure 9).
Section 10.1 “Power-up ramp conditions” added.
Reset pad description updated (5 V tolerant) in Table 3.
IRC frequency data added (see Figure 16 “Internal RC oscillator frequency versus
temperature”.
20101126
•
LPC1102 v.3
Preliminary data sheet -
LPC1102 v.1
Changed data sheet status to Preliminary.
20101116
Objective data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
-
© NXP B.V. 2013. All rights reserved.
40 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
15. Legal information
15.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
15.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
LPC1102_1104
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
41 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
16. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
LPC1102_1104
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 26 September 2013
© NXP B.V. 2013. All rights reserved.
42 of 43
LPC1102/1104
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
17. Contents
1
2
3
4
4.1
5
6
6.1
6.2
7
7.1
7.2
7.3
7.4
7.5
7.5.1
7.5.2
7.6
7.7
7.7.1
7.8
7.8.1
7.9
7.9.1
7.10
7.10.1
7.11
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6
Functional description . . . . . . . . . . . . . . . . . . . 8
ARM Cortex-M0 processor . . . . . . . . . . . . . . . . 8
On-chip flash program memory . . . . . . . . . . . . 8
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . . 8
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Nested Vectored Interrupt Controller (NVIC) . . 9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 10
IOCONFIG block . . . . . . . . . . . . . . . . . . . . . . 10
Fast general purpose parallel I/O . . . . . . . . . . 10
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SPI serial I/O controller. . . . . . . . . . . . . . . . . . 11
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General purpose external event
counter/timers . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.11.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.12
System tick timer . . . . . . . . . . . . . . . . . . . . . . 12
7.13
Windowed WatchDog Timer . . . . . . . . . . . . . . 12
7.13.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.14
Clocking and power control . . . . . . . . . . . . . . 13
7.14.1
Crystal oscillators . . . . . . . . . . . . . . . . . . . . . . 13
7.14.1.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . . 14
7.14.1.2 Watchdog oscillator . . . . . . . . . . . . . . . . . . . . 14
7.14.2
System PLL . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.14.3
Clock output (LPC1104 only) . . . . . . . . . . . . . 15
7.14.4
Wake-up process . . . . . . . . . . . . . . . . . . . . . . 15
7.14.5
Power control . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.14.5.1 Power profiles . . . . . . . . . . . . . . . . . . . . . . . . 15
7.14.5.2 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.14.5.3 Deep-sleep mode . . . . . . . . . . . . . . . . . . . . . . 16
7.15
System control . . . . . . . . . . . . . . . . . . . . . . . . 16
7.15.1
Start logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.15.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.15.3
Brownout detection . . . . . . . . . . . . . . . . . . . . . 16
7.15.4
Code security (Code Read Protection - CRP) 17
7.15.5
APB interface . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.15.6
AHBLite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.15.7
External interrupt inputs . . . . . . . . . . . . . . . . . 17
7.16
Emulation and debugging . . . . . . . . . . . . . . . 17
8
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 18
9
Static characteristics . . . . . . . . . . . . . . . . . . . 19
9.1
BOD static characteristics . . . . . . . . . . . . . . . 23
9.2
Power consumption . . . . . . . . . . . . . . . . . . . 23
9.3
CoreMark data . . . . . . . . . . . . . . . . . . . . . . . . 26
9.4
Electrical pin characteristics. . . . . . . . . . . . . . 26
10
Dynamic characteristics. . . . . . . . . . . . . . . . . 29
10.1
Power-up ramp conditions . . . . . . . . . . . . . . . 29
10.2
Flash memory . . . . . . . . . . . . . . . . . . . . . . . . 29
10.3
External clock. . . . . . . . . . . . . . . . . . . . . . . . . 30
10.4
Internal oscillators . . . . . . . . . . . . . . . . . . . . . 31
10.5
I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10.6
SPI interfaces. . . . . . . . . . . . . . . . . . . . . . . . . 32
11
Application information . . . . . . . . . . . . . . . . . 35
11.1
ADC usage notes. . . . . . . . . . . . . . . . . . . . . . 35
11.2
XTAL input . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11.3
Standard I/O pad configuration . . . . . . . . . . . 35
11.4
Reset pad configuration . . . . . . . . . . . . . . . . . 36
11.5
ADC effective input impedance . . . . . . . . . . . 37
12
Package outline. . . . . . . . . . . . . . . . . . . . . . . . 38
13
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 39
14
Revision history . . . . . . . . . . . . . . . . . . . . . . . 40
15
Legal information . . . . . . . . . . . . . . . . . . . . . . 41
15.1
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 41
15.2
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
15.3
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 41
15.4
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 42
16
Contact information . . . . . . . . . . . . . . . . . . . . 42
17
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 26 September 2013
Document identifier: LPC1102_1104