AN-940 APPLICATION NOTE One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Low Noise Amplifier Selection Guide for Optimal Noise Performance by Paul Lee INTRODUCTION When evaluating an amplifier’s performance for a low noise application, both internal and external noise sources must be considered. This application note briefly discusses the fundamentals of both internal and external noise and identifies the tradeoffs associated in selecting the optimal amplifier for low noise design. EXTERNAL NOISE SOURCES External noise includes any type of external influences, such as external components and electrical/electromagnetic interference. Interference is defined as any unwanted signals arriving as either voltage or current, at any of the amplifier’s terminals or induced in its associated circuitry. It can appear as spikes, steps, sine waves, or random noise. Interference can come from anywhere: machinery, nearby power lines, RF transmitters or receivers, computers, or even circuitry within the same equipment (that is, digital circuits or switching-type power supplies). If all interference is eliminated by careful design and/or layout of the board, there can still be random noise associated with the amplifier and its circuit components. Noise from surrounding circuit components must be accounted for. At temperatures above absolute zero, all resistances act as noise sources due to thermal movement of charge carriers called Johnson noise or thermal noise. This noise increases with resistance, temperature, and bandwidth. Voltage noise is shown in Equation 1. Vn 4kTBR (1) where: Vn is voltage noise. k is Boltzmann’s constant (1.38 × 10−23 J/K). T is the temperature in Kelvin (K). B is the bandwidth in hertz (Hz). R is the resistance in ohms (Ω). Current noise (noise associated with current flow) is shown in Equation 2 In 4kTB R where: In is current noise. k is Boltzmann’s constant (1.38 × 10−23 J/K). T is the temperature in Kelvin (K). B is the bandwidth in hertz (Hz). R is the resistance in ohms (Ω). Rev. D | Page 1 of 12 (2) AN-940 Application Note TABLE OF CONTENTS Introduction ...................................................................................... 1 Popcorn Noise ...............................................................................5 External Noise Sources .................................................................... 1 Summing the Noise Sources ........................................................5 Internal Noise Sources ..................................................................... 3 Noise Gain ......................................................................................6 Input-Referred Voltage Noise ..................................................... 4 Selecting Low Noise Op Amp ..........................................................7 Input-Referred Current Noise .................................................... 4 Conclusion..........................................................................................9 Flicker Noise.................................................................................. 5 References ........................................................................................ 12 Rev. D | Page 2 of 12 Application Note AN-940 Resistors INTERNAL NOISE SOURCES For the purposes of this application note, the resistor noise is limited to thermal (Johnson) noise. To keep a low level of this type of noise, resistance values should be as low as possible because RMS voltage of thermal (Johnson) noise is proportional to the square root of the resistor value. For example, a 1 kΩ resistor has a thermal noise of ~4 nV/√Hz at room temperature. Noise appearing at the amplifier’s output is usually measured as a voltage. However, it is generated by both voltage and current sources. All internal sources are generally referred to the input, that is, treated as uncorrelated or independent random noise generators in series or in parallel with the inputs of an ideal noise-free amplifier (see Figure 1). Because these noise sources are considered random and/or exhibit Gaussian distribution behavior, it is important to take proper care when summing the noise sources as discussed in the Summing the Noise Sources section. For an in-depth analysis and low noise designs, other types of resistor noise should be accounted for, such as contact noise and shot noise. A few practical notes follow and they should be considered when selecting a resistor. Choose the largest practical wattage resistors, as the contact noise is decreased with a larger volume of material. Choose low noise resistive element material Resistive elements composed of pure metals and/or metal alloys in bulk exhibits low noise characteristics. Such as Vishay Bulk Metal® foil technology resistors (such as, S102C, Z201) Wirewound technology resistors composed of metal alloys have similar noise characteristics as Bulk Metal foil technology, but are much more inductive. Metal film technology resistors as thin film are noisier than Bulk Metal foil or wirewound technology resistors because of significant noise contributions from occlusions, surface imperfections, and nonuniform depositions. Thick film and carbon composition resistors are the nosiest resistors. Reactances Reactances, such as capacitors and inductors, do not generate noise, but the noise current through reactances develops noise voltage as well as the associated parasitic. Practical Tips If the same noise appears at two or more points in a circuit (that is, input bias current cancellation circuitry), the two noise sources are correlated noise sources and a correlation coefficient factor should be included in the noise analysis. Further analysis of correlated noise is limited in this application note as typical correlation noise sources are less than 10% to 15% and they can usually be disregarded. Internal amplifier noise falls into four categories: Input-referred voltage noise and input-referred current noise are the most common specifications used for amplifier noise analysis. They are often specified as an input-referred spectral density function or the rms noise contained in Δf bandwidth and usually given in terms of nV/√Hz (for voltage noise) or pA/√Hz (for current noise). The /√Hz is needed because the noise power adds with (is cumulative over) bandwidth (Hz) or the voltage and current noise density adds with square root of the bandwidth (√Hz) (see Equation 1 and Equation 2). Output noise from a circuit can be reduced by lowering the total component resistance or by limiting the circuit bandwidth. Temperature reduction is generally not very helpful unless a resistor can be made very cold, because noise power is proportional to the absolute temperature, T(x) in Kelvin = x°C + 273.15° Input-referred voltage noise Input-referred current noise Flicker noise Popcorn noise en –+ + RS – in in (3) All resistors in a circuit generate noise. The effect of generated noise must always be considered. In practice, only resistors in the input and feedback paths (typically in high gain configurations) are likely to have an appreciable effect on total circuit noise. The noise can be considered as coming from either current sources or voltage sources (whichever is more convenient in a given circuit). Rev. D | Page 3 of 12 R2 R1 Figure 1. Op Amp Noise Model 07053-001 AN-940 Application Note INPUT-REFERRED VOLTAGE NOISE INPUT-REFERRED CURRENT NOISE Input-referred voltage noise (en) is typically viewed as a noise voltage source. Input-referred current noise (in) is typically seen as two noise current sources pumping currents through the two differential input terminals. Voltage noise is the noise specification that is usually emphasized; however, if input impedance levels are high, current noise is often the limiting factor in system noise performance. It is analogous to offsets, where the input offset voltage often bears the blame for output offset, when in reality the bias current causes the output offset where input impedances are high. Note the following points about input-referred voltage noise: Op amp voltage noise can be lower than 1 nV/√Hz for the highest performance amplifiers. Although bipolar op amps traditionally have less voltage noise than FET op amps, they also have substantially greater current noise. Bipolar amplifier noise characteristics are dependent on the quiescent current. Present day FET op amps are capable of obtaining both low current noise and voltage noise similar to bipolar amplifier performance, though not as low as the best bipolar input amplifiers. Shot noise (sometimes called Schottky noise) is current noise due to random distribution of charge carriers in the current flow through a potential barrier, such as a PN junction. The shot noise current, in, is obtained from the formula in 2 I B qB (4) where: IB is the bias current in ampere (A). q is the electron charge in coulomb (1.6 × 10−19 C). B is the bandwidth in hertz (Hz). The current noise of a simple bipolar and JFET op amp is typically within 1 dB or 2 dB of the shot noise of the input bias current. This specification is not always listed on data sheets. Note the following points regarding input-referred noise: Rev. D | Page 4 of 12 The current noise of typical bipolar transistor op amps, such as the OP27, is about 400 fA/√Hz, where IB is 10 nA, and does not vary much with temperature except for bias, current-compensated amplifiers. The current noise of JFET input op amps (such as the AD8610: 5 fA/√Hz at IB = 10 pA) while lower, doubles for every 20°C chip temperature increase, because JFET op amp bias currents double for every 10°C increase. Traditional voltage feedback op amps with balanced inputs usually have equal (correlated and uncorrelated) current noise on both their inverting and noninverting inputs. Many amplifiers, especially those amps with input bias current cancellation circuits, have considerably larger correlated than uncorrelated noise components. Overall, noise can be improved by adding an impedance-balancing resistor (matching impedances on both positive and negative input pins). Application Note AN-940 FLICKER NOISE POPCORN NOISE The noise of op amps is Gaussian with constant spectral density (white noise), over a wide range of frequencies. As frequency decreases, the spectral density starts to rise because of the fabrication process, the IC device layout, and the device type at a rate of about 3 dB per octave for CMOS amplifiers, 3.5 dB to 4.5 dB per octave for bipolar amplifiers, or up to 5 dB per octave for JFET amplifiers. Popcorn noise (not specified or advertised) is an abrupt shift in offset voltage or current lasting for several milliseconds with amplitude from several microvolts to hundreds of microvolts. This burst or pop is random. Low temperatures and high source resistances usually produce the most favorable conditions for popcorn noise. Although the root cause of popcorn noise is not absolute, both metallic contamination and internal or surface defects in the silicon lattice can cause popcorn noise in ICs. Although considerable work has been done to reduce the sources of popcorn noise in modern wafer fabrication, it cannot be eliminated. Further analysis of popcorn noise is beyond the scope of this application note. This low frequency noise characteristic is known as flicker noise or 1/f noise because the noise power spectral density goes inversely with frequency (1/f). It has a −1 slope on a log plot. The frequency at which an extrapolated −3 dB per octave (for a CMOS-type amplifier) spectral density line intersects the broadband constant spectral density value is known as the 1/f corner frequency and is a figure of merit for the amplifier (see Figure 2). Bipolar and JFET amplifiers typically have lower 1/f corner frequency than CMOS amplifiers. 100 SUMMING THE NOISE SOURCES If the noise sources are uncorrelated (that is, one noise signal cannot be transformed into the other), the resulting noise is not their arithmetic sum, but the square root of the sum of their squares. EXTRAPOLATED 1/f SPECTRAL NOISE DENSITY 1 EXTRAPOLATED CONSTANT SPECTRAL NOISE DENSITY 1/f CORNER FREQUENCY 1 10 100 FREQUENCY (Hz) Note the following: 1k 10k Figure 2. Spectral Noise Density Any resistance in the noninverting input has Johnson noise and converts current noise to a voltage noise. Johnson noise in feedback resistors can be significant in high resistance circuits. Figure 3 visually shows the Equation 5 as the summation of vectors by using the Pythagorean Theorem. Vni, TOTAL Vn (REX) RS × in en 07053-006 0.1 0.1 (5) where: Vni, TOTAL is the total noise referred-to-input (RTI). en is input-referred voltage noise. in is input-referred current noise. RS is an equivalent source or input resistance to the amplifier. Vn (REX) is voltage noise from external circuitry. 10 07053-005 VOLTAGE NOISE (nV/√Hz) Vni , TOTAL (e n ) 2 (R S i n ) 2 Vn (R EX ) 2 Figure 3. Vector Summation of Noise Sources Rev. D | Page 5 of 12 AN-940 Application Note OP AMP NOISE MODEL COMBINED RTI NOISE (Vni, TOTAL) en –+ + in RESISTOR NOISE RS – RESISTOR NOISE – in R1 R2 + RESISTOR NOISE R1 R2 07053-007 –+ Figure 4. Simplifying the Amplifier Noise Circuit The noises previously discussed can be grouped into referredto-input (RTI) noise of the amplifier circuit. To calculate the total output noise of the amplifier circuit, the total combined noise on the input must be multiplied by the amplifier circuit’s noise gain. Noise gain is the gain of the amplifier’s circuit for referred-to-input noise and it is typically used to determine the stability of the amplifier circuit. In some cases, the noise gain and the signal gain are not equivalent (see Figure 5). Note that the closed-loop bandwidth is determined by dividing the gain bandwidth product (or unity gain frequency) by the noise gain of the amplifier circuit. NOISE SOURCE CASE 1: SIGNAL SOURCE To simplify the noise gain calculation, the noise sources in the simple amplifier circuit in Figure 1 can be reduced to a single total RTI noise source (Vni, TOTAL), as shown in Figure 4. It is a common practice to lump the total combined RTI noise to the noninverting input of the amplifier. CASE 2: SIGNAL SOURCE Vno, TOTAL GN Vni , TOTAL where: Vno, TOTAL is the total referred-to-output (RTO) noise. Vni, TOTAL is the total referred-to-input (RTI) noise GN 1 R1 R2 + – R2 R1 07053-008 NOISE GAIN Figure 5. Signal Gain vs. Noise Gain Case 1: In a noninverting configuration, both the signal gain and the noise gain are equal to 1 + R1/R2. Case 2: In an inverting configuration, signal gain is equal to −(R1/R2), but the noise gain is still equal to 1 + R1/R2. where: GN is the noise gain. R1 is the feedback equivalent impedance. R2 is the gain setting equivalent impedance. Rev. D | Page 6 of 12 Application Note AN-940 SELECTING LOW NOISE OP AMP An amplifier can be selected where its noise contribution is negligible compared to the source resistance by using a figure of merit, RS, OP, of an op amp. It can be calculated by using an amplifier’s noise specification. If an op amp is driven with a source resistance, the equivalent noise input becomes the square root of the sum of the squares of the amplifier’s voltage noise, the voltage generated by the source resistance, and the voltage caused by the amplifiers current noise flowing through the source impedance. RS , OP For very low source resistances, the noise generated by the source resistance and amplifier current noise contribute insignificantly to the total. In this case, the noise at the input is effectively only the voltage noise of the op amp. en in (7) where: en is input-referred voltage noise. in is input-referred current noise. If the source resistance is high, the Johnson noise of the source resistance may dominate both the op amp voltage noise and the voltage due to the current noise. However, note that, because the Johnson noise only increases with the square root of the resistance, while the noise voltage due to the current noise is directly proportional to the input impedance, the amplifier’s current noise always dominates for a high enough value of input impedance. When an amplifier’s voltage and current noise are high enough, there may be no value of input resistance for which Johnson noise dominates. Figure 6 shows a comparison of the voltage noise density of a number of high voltage (up to 44 V) op amps from Analog Devices, Inc., vs. RS, OP at 1 kHz. The diagonal line plots the Johnson noise associated with resistance. 100 f = 1kHz JOHNSON NOISE LINE OF SOURCE RESISTANCE AD8622/AD8624 OP285 OP467 AD8610/ AD8620 OP271 10 VOLTAGE NOISE (nV/√Hz) OPx177 OP275 OP213 OPx84 OP270 OP27/OP37 AD743/AD745 ADA4004 ADA4075-2 AD8597/AD8599 1 0.1 10 100 1k 10k SOURCE RESISTANCE (Ω) Figure 6. Analog Devices Op Amp Noise Plot Rev. D | Page 7 of 12 100k 1M 07053-002 AD797 AN-940 Application Note 2. Similar types of graph can be constructed for a chosen frequency from the data in the op amp data sheet (see Figure 8). For example, the AD8599 has an input-referred voltage noise of 1.07 nV/√Hz and an input-referred current noise of 2.3 pA/√Hz at 1 kHz. The RS, OP is about ~465 Ω at 1 kHz. In addition, note the following: 4. The Johnson noise associated with this device is equivalent to a source resistor of about 69.6 Ωsee Figure 6). For a source resistance above ~465 Ω, the noise voltage produced by the amplifier’s current noise exceeds that contributed by the source resistance; the amplifier’s current noise becomes the dominant noise source. Any amplifiers below and to the right of the lines are good low noise op amps for the design as highlighted in the shade of gray in Figure 7. For the example shown in Figure 7, the following devices are good candidates for the design: AD8597, AD8599, AD797, ADA4075-2, ADA4004, OP270, OP27/OP37, AD743/AD745, and OP184. To use the graph (see Figure 7), follow Step 1 through Step 4. Typically, the source resistances are known (such as sensor impedances). If the resistances are not known, calculate them from the surrounding or preceding circuit components. 100 f = 1kHz JOHNSON NOISE LINE LOW NOISE BOUNDRY IDEAL OP AMPS FOR A LOW NOISE APPLICATION AD8622/AD8624 OP285 AD8610/ AD8620 OP467 OP271 10 VOLTAGE NOISE (nV/√Hz) 1. STEP 2 OP275 OPx177 STEP 3 OP213 OPx84 OP270 OP27/OP37 AD743/AD745 ADA4004 ADA4075-2 AD8597/AD8599 1 AD797 STEP 4 0.1 10 100 1k 10k SOURCE RESISTANCE (Ω) Figure 7. Selecting Op Amp for Low Noise Design Rev. D | Page 8 of 12 100k 1M 07053-003 3. Locate the given source resistance, such as 1 kΩ, on the Johnson noise line. Create a horizontal line from the point located in Step 2 to the right of the plot. Create a line down and to the left from the point located in Step 2) by decreasing one decade of voltage noise per one decade of resistance. Application Note AN-940 CONCLUSION Consider all potential noise sources when evaluating an amplifier’s noise performance for low noise design. The key noise contribution of an op amp is dependent on source resistance as follows: RS >> RS, OP; input-referred current noise dominates. RS = RS, OP; amplifier noise and resistor noise are equal RS << RS, OP; input-referred voltage noise dominates. In summary, reduce or eliminate interference signals by Proper layout techniques to reduce parasitics. Proper ground techniques, such as isolating digital and analog ground. Proper shielding. For resistive noise sources, use the following rules: Restrict bandwidth to only what is necessary. Reduce resistor value where possible. Use low noise resistors, such as bulk metal foil, wirewound, and metal film technology resistors. Reduce the number of resistive noise sources where possible. Use Figure 8 and Figure 9 to assist with the selection of an Analog Devices low noise amplifier using the criteria described in this application note. For more information on noise, see the article, “Noise Optimization in Sensor Signal Conditioning Circuit” available at http://www.analog.com/noiseoptimization. Rev. D | Page 9 of 12 PART NUMBER AD797 AD8597/ AD8599 ADA4004-1/ ADA4004-2/ ADA4004-4 AD8676 AD8675 AD8671/ AD8672/ AD8674 ADA4075-2 OP27 OP37 OP270 OP470 AD743 AD745 OP184/ OP284/ OP484 AD8655/ AD8656 OP113 / OP213/ OP413 SSM2135 ADA4528-1 OP285 AD8610/ AD8620 OP275 OP467 ADA4627-1 OP471 OP1177/ OP2177/ OP4177 AD8510/ AD8512/ AD8513 AD8651/ AD8652 AD8646/ AD8647/ AD8648 AD8605/ AD8606/ AD8608 AD8691/ AD8692/ AD8694 OP162/ OP262/ OP462 OP07 OP07D AD8677 AD8615/ AD8616/ AD8618 AD8519/ AD8529 AD8665/ AD8666/ AD8668 AD8622/ AD8624 AD8661/ AD8662/ AD8664 OP97 OP297 OP497 OP777/ OP727/ OP747 Application Note VSY (V) VOS MAX (µV) TCVOS (µV/°C) GBP (MHz) SLEW RATE (V/µs) ISY/AMP MAX (mA) en @ 1kHz (nV/√Hz) 1kHz (pA/√Hz) in @ RS, OP @ 1kHz (Ω) 1/f CORNER (Hz) IB MAX (nA) ISC (mA) CMRR MIN (dB) PSRR MIN (dB) NUMBER OF AMPS 10 TO 36 9 TO 36 40 120 0.2 0.8 8 10 20 15 10.5 5.7 0.9 1.07 2 2.3 450 465 60 9 900 200 80 52 120 120 120 120 10 TO 36 125 0.7 12 2.7 2.2 1.8 1.2 1500 5 90 25 110 110 10 TO 36 10 TO 36 10 TO 36 50 75 75 0.2 0.2 0.3 10 10 10 2.5 2.5 4 3.4 2.9 3.5 2.8 2.8 2.8 0.3* 0.3* 0.3* — — — 10 10 10 2 2 12 40 40 30 111 114 100 106 120 110 ±4.5 TO ±18 8 TO 44 8 TO 44 9 TO 36 1000 100 100 75 0.3 0.3 0.3 0.2 6.5 8 40 5 12 2.8 17 2.4 2.25 5.7 4.7 3.25 2.8 3.2 3.2 3.2 1.2 0.4 0.4 0.6 2333 8000 8000 5333 5 2.7 2.7 5 100 80 75 20 40 30 30 15 110 100 100 106 106 140 140 110 9.6 TO 36 9.6 TO 36 3 TO 36 1000 500 100 2 2 0.2 4.5 20 4.25 2.8 12.5 4 10 10 2 3.2 3.2 3.9 0.0069 0.0069 0.4 463,768 463,768 9750 50 50 10 0.4 0.25 450 40 40 10 80 90 86 90 100 90 2.7 TO 5.5 250 0.4 28 11 4.5 4 — — 3000 0.01 220 85 88 4 TO 36 150 0.2 3.4 1.2 3 4.7 0.4 11,750 10 600 40 96 100 4 TO 36 2.2 TO 5.5 9 TO 36 10 TO 27 2000 2.5 250 100 — 0.002 1 0.5 3.5 4 9 25 0.9 0.45 22 60 3 1.7 2.5 3.5 5.2 5.6* 6 6 0.5 0.7* 0.9 0.005 10,400 8000 6667 1,200,000 3 NONE 125 1000 750 0.4 350 0.01 30 30 30 65 87 135 80 90 90 130 85 100 9 TO 44 9 TO 36 9 TO 36 1000 500 200 2 3.5 1 9 28 19 22 170 84 2.5 2.5 7.500 6 6 6.1 1.5 0.8 0.0016 4000 7500 3,812,500 2.24 8 250 350 600 5 14 40 45 80 80 106 85 96 106 1 1/ 2 1/ 2/ 4 2 1 1/ 2/ 4 2 1 1 2/ 4 1 1 1/ 2/ 4 1/ 2 1/ 2/ 4 2 1 2 1/ 2 2 4 1 9 TO 36 5 TO 36 1800 60 4 0.2 6.5 1.3 8 0.7 2.75 0.5 6.5 7.9 0.4 0.2 16,250 39,500 5 10 60 2 10 25 95 120 95 120 9 TO 36 400 1 8 20 2.5 8 — — 100 0.08 70 86 86 2.7 TO 5.5 350 4 50 41 14 8 0.025 320,000 10000 0.01 80 80 76 2.7 TO 5.5 2500 1.8 24 11 1.5 8 — — 1000 0.001 120 67 63 2.7 TO 5.5 300 1 10 5 1.2 8 0.01 800,000 500 0.001 80 85 80 2.7 TO 6 2000 1.3 10 5 1.05 8 0.05 160,000 3000 0.001 80 70 80 2.7 TO 12 325 1 15 13 0.8 9.5 0.4 23,750 10 600 30 70 60 6 TO 36 75 0.3 0.6 0.3 4 9.6 0.12 80,000 100 4 30 106 94 8 TO 36 8 TO 36 2.7 TO 5.5 150 130 500 0.5 0.5 1.5 0.6 0.6 24 0.2 0.2 12 1.3 1.3 2 10 10 10 0.074 0.074 0.05 135,135 135,135 200,000 8 8 1000 1 1 0.001 30 30 150 120 120 80 115 115 70 2.7 TO 12 1100 2 8 2.9 1.2 10 0.4 25,000 80 300 70 63 60 5 TO 16 2500 3 4 3.5 1.55 10 0.1 100,000 1000 0.001 140 90 98 4 TO 36 125 0.5 0.56 0.48 0.250 11 0.15 73,333 20 200 40 125 125 5 TO 16 160 4 4 3.5 1.55 12 0.1 120,000 1000 0.001 140 90 95 4 TO 40 75 0.3 0.9 0.2 0.38 14 0.02* 1,166,667 200 0.15 10 110 110 3 TO 36 100 0.3 0.7 0.2 0.35 15 0.13 115,384 20 11 30 110 120 *REFER TO DEVICE DATA SHEET FOR SPECIFICATION CONDITIONS. Figure 8. Analog Devices Low Input Voltage Noise Amplifier Selection Table Rev. D | Page 10 of 12 4 1/ 2/ 4 1/ 2/ 4 1/ 2 1/ 2(SD)/ 4 1/ 2/ 4 1(SD)/ 2(SD)/ 4(SD) 1/ 2/ 4 1 1 1 1/ 2/ 4 1/ 2 1/ 2/ 4 2/ 4 1/ 2/ 4 1/ 2/ 4 1/ 2/ 4 07053-004 AN-940 AN-940 ISY/AMP MAX (mA) en @ 1kHz (nV/√Hz) 1kHz (fA/√Hz) in @ RS, OP @ 1kHz (Ω) 1/f CORNER (Hz) IB MAX (pA) 3 0.7 35 0.22 159,090,909 100 5 0.850 16 0.5 35,000,000 - 3.5 3 0.290 27.5 0.5 57,000,000 2 1.9 3* 0.900 16 0.8 200 1 19 84 7.500 6.1 500 5 1 1.8 0.2 30 10 TO 26 100 0.5 25 60 3.500 8 TO 36 2500 4 1.4 3.3 0.220 AD743 9.6 TO 36 1000 2 4.5 2.8 10 3.2 6.9 463,768 50 0.4 40 80 90 1 AD745 9.6 TO 36 500 2 20 12.5 10 3.2 6.9 463,768 50 0.25 40 90 100 1 AD711C 9 TO 36 250 5 4 20 2.8 18 10 1,800,000 200 25 25 86 86 1 AD8605/ AD8606/ AD8608 2.7 TO 6 300 1 10 5 1.2 8 10 800,000 500 1 80 85 80 1/ 2/ 4 OP282/ OP482 9 TO 36 3000 10 4 9 0.250 36 10 3,600,000 40 100 10 70 110 2/ 4 2/ 4 1/ 2/ 4 VSY (V) VOS MAX (µV) TCVOS (µV/°C) GBP (MHz) SLEW RATE (V/µs) AD549 10 TO 36 AD8627/ AD8626/ AD8625 10 TO 26 500 10 5 750 2.5 5 AD8641/ AD8642 AD8643 5 TO 26 750 2.5 AD820/ AD822/ AD824 5 TO 36 1000 ADA4627-1 8 TO 36 AD548K/B 9 TO 36 AD8610/ AD8620 ADA4062-2 ADA4062-4 PART NUMBER AD8682 AD8684 ADA4000-1 ADA4000-2 ADA4000-4 IOUT (mA) CMRR MIN (dB) PSRR MIN (dB) NUMBER OF AMPS 0.06 20 90 90 1 1 15* 76 80 1/ 2/ 4 250 1 12* 90 90 1/ 2/ 4 20,000,000 90 10 15* 74* 70 1/ 2/ 4 1.6 3,812,500 250 5 45 106 106 1 1.8 16,666,666 700 10 15 82 86 1 6 5 1,200,000 1000 10 45 90 100 1/ 2 36 5 7,200,000 30 50 20 73 74 2/ 4 9 TO 36 1000 10 3.5 9 0.250 36 10 3,600,000 40 20 10 70 92 8 TO 36 1700 2 5 20 1.650 16 10 1,600,000 100 40 28 80 82 OP97/ OP297/ OP497 4 TO 40 75* 0.3* 0.9* 0.2* 0.38* 14* 20* 1,166,667* 200* 150 10 110* 110* 1/ 2/ 4 AD8651/ AD8652 2.7 TO 5.5 350 4 50 41 14 8 25 320,000 10,000 10 80 80 76 1/ 2 AD8615/ AD8616/ AD8618 2.7 TO 6 500 1.5 24 12 1.3 10 50 200,000 1000 1 150 80 70 1/ 2/ 4 AD8691/ AD8692/ AD8694 2.7 TO 6 2000 1.3 10 5 1.05 8 50 160,000 3000 1 80 70 80 1(SD)/ 2(SD)/ 4(SD) AD8661/ AD8662/ AD8664 5 TO 6 160 4 4 3.5 1.55 12 100 120,000 1000 1 140 90 95 1/ 2/ 4 OP07 6 TO 36 75 0.3 0.6 0.3 4 9.6 120 80,000 100 4000 30 106 94 1 AD8622/ AD8624 5 TO 36 125 0.5 0.56 0.48 0.250 11 150 73,333 20 200 40 125 125 2/ 4 *REFER TO DEVICE DATA SHEET FOR SPECIFICATION CONDITIONS. Figure 9. Analog Devices Low Input Current Noise Amplifier Selection Table Rev. D | Page 11 of 12 07053-104 Application Note AN-940 Application Note REFERENCES Analog Devices, Inc., AN-280 Application Note Mixed Signal Circuit Techniques. Barrow, J., and Paul Brokaw. 1989. “Grounding for Low- and High-Frequency Circuits.” Analog Dialogue. Analog Devices, Inc. (23-3). Bennett, W. R. 1960. Electrical Noise. New York: McGraw-Hill. Bowers, Derek F. 1989. “Minimizing Noise in Analog Bipolar Circuit Design.” IEEE Press. Brockman, Don and Arnold Williams. AN-214 Application Note Ground Rules for High-Speed Circuits. Analog Devices, Inc. Brokaw, Paul. 2000. AN-202 Application Note An IC Amplifier User’s Guide to Decoupling, Grounding, and Making Things Go Right for a Change. Analog Devices, Inc. (February). Brokaw, Paul and Jeff Barrow. AN-345 Application Note Grounding for Low- and High-Frequency Circuits. Analog Devices, Inc. Bryant, James Bryant and Lew Counts. 1990. “Op Amp Issues–Noise ” Analog Dialogue. Analog Devices Inc. (24–2). Freeman, J. J. 1958. Principles of Noise. New York: John Wiley & Sons, Inc. Gupta, Madhu S., ed., 1977. Electrical Noise: Fundamentals & Sources. New York: IEEE Press. Collection of classical reprints. Hernik, Yuval and Belman, Michael. Linearity and Noise Capabilities of Ultra High Precision Bulk Metal® Foil Resistors. Vishay Intertechnology, Inc. (February 2010). Johnson, J. B. 1928. “Thermal Agitation of Electricity in Conductors” (Physical Review 32): 97–109. Motchenbacher, C. D., and J. A. Connelly. 1993. Low-Noise Electronic Design. New York: John Wiley & Sons, Inc. Nyquist, H. 1928. “Thermal Agitation of Electric Charge in Conductors” (Physical Review 32): 110–113. Rice, S.O. 1944. “Math Analysis for Random Noise” Bell System Technical Journal (July): 282–332. Rich, Alan. 1982. “Understanding Interference-Type Noise.” Analog Dialogue. Analog Devices Inc., (16–3). Rich, Alan. 1983. “Shielding and Guarding.” Analog Dialogue. Analog Devices Inc. (17–1). Ryan, Al and Tim Scranton. 1984. “DC Amplifier Noise Revisited.” Analog Dialogue. Analog Devices, Inc., (18–1). Schottky, W. 1926. “Small-Shot Effect and Flicker Effect.” (Phys. Rev. 28): 74–103. Van Der Ziel, A. 1954. Noise. Englewood Cliffs, NJ: Prentice-Hall, Inc. Vishay Intertechnology, Inc. AN0003 Application Note Audio Noise Reduction Through the Use of Bulk Metal® Foil Resistors-“Hear the Difference”. ©2007–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. AN07053-0-7/11(D) Rev. D | Page 12 of 12