PHILIPS LPC2378FBD144

LPC2378
Single-chip 16-bit/32-bit microcontrollers; 512 kB flash with
ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
Rev. 01 — 6 December 2006
Preliminary data sheet
1. General description
The LPC2378 microcontroller is based on a 16-bit/32-bit ARM7TDMI-S CPU with
real-time emulation that combines the microcontroller with 512 kB of embedded
high-speed flash memory. A 128-bit wide memory interface and a unique accelerator
architecture enable 32-bit code execution at the maximum clock rate. For critical
performance in interrupt service routines and DSP algorithms, this increases performance
up to 30 % over Thumb mode. For critical code size applications, the alternative 16-bit
Thumb mode reduces code by more than 30 % with minimal performance penalty.
The LPC2378 is ideal for multi-purpose serial communication applications. It incorporates
a 10/100 Ethernet Media Access Controller (MAC), USB full speed device with 4 kB of
endpoint RAM, four UARTs, two CAN channels, an SPI interface, two Synchronous Serial
Ports (SSP), three I2C interfaces, an I2S interface, and an External Memory Controller
(EMC). This blend of serial communications interfaces combined with an on-chip 4 MHz
internal oscillator, SRAM of 32 kB, 16 kB SRAM for Ethernet, 8 kB SRAM for USB and
general purpose use, together with 2 kB battery powered SRAM make this device very
well suited for communication gateways and protocol converters. Various 32-bit timers, an
improved 10-bit ADC, 10-bit DAC, PWM unit, a CAN control unit, and up to 104 fast GPIO
lines with up to 50 edge and up to four level sensitive external interrupt pins make these
microcontrollers particularly suitable for industrial control and medical systems.
2. Features
n ARM7TDMI-S processor, running at up to 72 MHz.
n Up to 512 kB on-chip flash program memory with In-System Programming (ISP) and
In-Application Programming (IAP) capabilities. Flash program memory is on the ARM
local bus for high performance CPU access.
n 32 kB of SRAM on the ARM local bus for high performance CPU access.
n 16 kB SRAM for Ethernet interface. Can also be used as general purpose SRAM.
n 8 kB SRAM for general purpose DMA use also accessible by the USB.
n Dual Advanced High-performance Bus (AHB) system that provides for simultaneous
Ethernet DMA, USB DMA, and program execution from on-chip flash with no
contention between those functions. A bus bridge allows the Ethernet DMA to access
the other AHB subsystem.
n EMC provides support for static devices such as flash and SRAM as well as off-chip
memory mapped peripherals.
n Advanced Vectored Interrupt Controller (VIC), supporting up to 32 vectored interrupts.
n General Purpose AHB DMA controller (GPDMA) that can be used with the SSP serial
interfaces, the I2S port, and the Secure Digital/MultiMediaCard (SD/MMC) card port,
as well as for memory-to-memory transfers.
LPC2378
NXP Semiconductors
Fast communication chip
n Serial Interfaces:
u Ethernet MAC with associated DMA controller. These functions reside on an
independent AHB bus.
u USB 2.0 full-speed device with on-chip PHY and associated DMA controller.
u Four UARTs with fractional baud rate generation, one with modem control I/O, one
with IrDA support, all with FIFO.
u CAN controller with two channels.
u SPI controller.
u Two SSP controllers, with FIFO and multi-protocol capabilities. One is an alternate
for the SPI port, sharing its interrupt and pins. These can be used with the GPDMA
controller.
u Three I2C-bus interfaces (one with open-drain and two with standard port pins).
u I2S (Inter-IC Sound) interface for digital audio input or output. It can be used with
the GPDMA.
n Other peripherals:
u SD/MMC memory card interface.
u 104 General purpose I/O pins with configurable pull-up/down resistors.
u 10-bit ADC with input multiplexing among 8 pins.
u 10-bit DAC.
u Four general purpose timers/counters with 8 capture inputs and 10 compare
outputs. Each timer block has an external count input.
u One PWM/timer block with support for three-phase motor control. The PWM has
two external count inputs.
u Real-Time Clock (RTC) with separate power pin, clock source can be the RTC
oscillator or the APB clock.
u 2 kB SRAM powered from the RTC power pin, allowing data to be stored when the
rest of the chip is powered off.
u WatchDog Timer (WDT). The WDT can be clocked from the internal RC oscillator,
the RTC oscillator, or the APB clock.
n Standard ARM test/debug interface for compatibility with existing tools.
n Emulation trace module supports real-time trace.
n Single 3.3 V power supply (3.0 V to 3.6 V).
n Four reduced power modes: idle, sleep, power down, and deep power down.
n Four external interrupt inputs configurable as edge/level sensitive. All pins on PORT0
and PORT2 can be used as edge sensitive interrupt sources.
n Processor wake-up from Power-down mode via any interrupt able to operate during
Power-down mode (includes external interrupts, RTC interrupt, USB activity, Ethernet
wake-up interrupt).
n Two independent power domains allow fine tuning of power consumption based on
needed features.
n Each peripheral has its own clock divider for further power saving.
n Brownout detect with separate thresholds for interrupt and forced reset.
n On-chip power-on reset.
n On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz.
n 4 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used as
the system clock. When used as the CPU clock, does not allow CAN and USB to run.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
2 of 54
LPC2378
NXP Semiconductors
Fast communication chip
n On-chip PLL allows CPU operation up to the maximum CPU rate without the need for
a high frequency crystal. May be run from the main oscillator, the internal RC
oscillator, or the RTC oscillator.
n Boundary scan for simplified board testing.
n Versatile pin function selections allow more possibilities for using on-chip peripheral
functions.
3. Applications
n
n
n
n
Industrial control
Medical systems
Protocol converter
Communications
4. Ordering information
Table 1.
Ordering information
Type number
Package
LPC2378FBD144
Name
Description
Version
LQFP144
plastic low profile quad flat package; 144 leads; body 20 × 20 × 1.4 mm
SOT486-1
4.1 Ordering options
Ordering options
RMII
yes
LPC2378_1
Preliminary data sheet
SD/ GP
MMC DMA
2
yes
yes
Temp
range
DAC channels
58 MiniBus: 8 data, 16
address, and 2 chip
select lines
USB
device
+ 4 kB
FIFO
CAN channels
2
Ether
net
ADC channels
32 16 8
Total
LPC2378FBD144 512
External bus
RTC
SRAM (kB)
GP/USB
Flash
(kB)
Local bus
Type number
Ethernet buffer
Table 2.
8
1
−40 °C to
+85 °C
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
3 of 54
LPC2378
NXP Semiconductors
Fast communication chip
5. Block diagram
TMS TDI
XTAL1
VDD(3V3)
XTAL2
VDDA
VDD(1V8)
RESET
trace signals
P0, P1, P2,
P3, P4
LPC2378
32 kB
SRAM
HIGH-SPEED
GPI/O
104 PINS
TOTAL
512 kB
FLASH
INTERNAL
CONTROLLERS
EINT3 to EINT0
P0, P2
2 · CAP0/CAP1/
CAP2/CAP3
4 · MAT2,
2 · MAT0/MAT1/
MAT3
6 · PWM1
ARM7TDMI-S
SRAM FLASH
AHB2
RMII(8)
TEST/DEBUG
INTERFACE
PLL
SYSTEM
FUNCTIONS
system
clock
INTERNAL RC
OSCILLATOR
VECTORED
INTERRUPT
CONTROLLER
AHB
BRIDGE
16 kB
SRAM
ETHERNET
MAC WITH
DMA
EMULATION
TRACE MODULE
TRST TCK TDO
EXTIN0 DBGEN
AHB
BRIDGE
MASTER AHB TO SLAVE
PORT APB BRIDGE PORT
AHB TO
APB BRIDGE
EXTERNAL
MEMORY
CONTROLLER
8 kB
SRAM
USB WITH
4 kB RAM
AND DMA
I2S INTERFACE
P0, P1
LEGACY GPI/O
56 PINS TOTAL
SSP1 INTERFACE
8 · AD0
A/D CONVERTER
2 · PCAP1
SCK, SCK0
MOSI, MOSI0
MISO, MISO0
SSEL, SSEL1
SCK1
MOSI1
MIS01
SSEL1
MCICLK, MCIPWR
SD/MMC CARD
INTERFACE
MCICMD,
MCIDAT[3:0]
D/A CONVERTER
UART0, UART2, UART3
TXD0, TXD2, TXD3
RXD0, RXD2, RXD3
2 kB BATTERY RAM
TXD1
RXD1
DTR1, RTS1
power domain 2
RTCX1
RTCX2
VBUS
2 · USB_D+/USB_D2 · USB_CONNECT
2 · USB_UP_LED
I2SRX_CLK
I2STX_CLK
I2SRX_WS
I2STX_WS
I2SRX_SDA
I2STX_SDA
SPI, SSP0 INTERFACE
VBAT
WE, OE, CS0, CS1
GP DMA
CONTROLLER
PWM1
AOUT
D[7:0]
A[15:0]
AHB1
EXTERNAL INTERRUPTS
CAPTURE/COMPARE
TIMER0/TIMER1/
TIMER2/TIMER3
VREF
VSSA, VSS
VDD(DCDC)(3V3)
RTC
OSCILLATOR
REALTIME
CLOCK
UART1
DSR1, CTS1, DCD1,
RI1
ALARM
RD1, RD2
TD1, TD2
CAN1, CAN2
WATCHDOG TIMER
SCL0, SCL1, SCL2
SDA0, SDA1, SDA2
I2C0, I2C1, I2C2
SYSTEM CONTROL
002aac574
Fig 1. LPC2378 block diagram
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
4 of 54
LPC2378
NXP Semiconductors
Fast communication chip
6. Pinning information
109
144
6.1 Pinning
1
108
LPC2378FBD144
72
73
37
36
002aac584
Fig 2. LPC2378 pinning
6.2 Pin description
Table 3.
Pin description
Symbol
Pin
P0[0] to P0[31]
P0[0]/RD1/TXD/
SDA1
P0[1]/TD1/RXD3/
SCL1
P0[2]/TXD0
66[1]
67[1]
141[1]
P0[3]/RXD0
142[1]
P0[4]/
I2SRX_CLK/
RD2/CAP2[0]
116[1]
Type
Description
I/O
Port 0: Port 0 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 0 pins depends upon the pin function selected via the Pin Connect
block.
I/O
P0[0] — General purpose digital input/output pin.
I
RD1 — CAN1 receiver input.
O
TXD3 — Transmitter output for UART3.
I/O
SDA1 — I2C1 data input/output (this is not an open drain pin).
I/O
P0[1] — General purpose digital input/output pin.
O
TD1 — CAN1 transmitter output.
I
RXD3 — Receiver input for UART3.
I/O
SCL1 — I2C1 clock input/output (this is not an open drain pin).
I/O
P0[2] — General purpose digital input/output pin.
O
TXD0 — Transmitter output for UART0.
I/O
P0[3] — General purpose digital input/output pin.
I
RXD0 — Receiver input for UART0.
I/O
P0[4] — General purpose digital input/output pin.
I/O
I2SRX_CLK — Receive Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I2S-bus specification.
I
RD2 — CAN2 receiver input.
I
CAP2[0] — Capture input for Timer 2, channel 0.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
5 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P0[5]/
I2SRX_WS/
TD2/CAP2[1]
115[1]
I/O
P0[5] — General purpose digital input/output pin.
I/O
I2SRX_WS — Receive Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I2S-bus specification.
O
TD2 — CAN2 transmitter output.
I
CAP2[1] — Capture input for Timer 2, channel 1.
I/O
P0[6] — General purpose digital input/output pin.
I/O
I2SRX_SDA — Receive data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I2S-bus specification.
I/O
SSEL1 — Slave Select for SSP1.
O
MAT2[0] — Match output for Timer 2, channel 0.
I/O
P0[7] — General purpose digital input/output pin.
I/O
I2STX_CLK — Transmit Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I2S-bus specification.
I/O
SCK1 — Serial Clock for SSP1.
O
MAT2[1] — Match output for Timer 2, channel 1.
I/O
P0[8] — General purpose digital input/output pin.
I/O
I2STX_WS — Transmit Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I2S-bus specification.
I/O
MISO1 — Master In Slave Out for SSP1.
P0[6]/
I2SRX_SDA/
SSEL1/MAT2[0]
P0[7]/
I2STX_CLK/
SCK1/MAT2[1]
P0[8]/
I2STX_WS/
MISO1/MAT2[2]
P0[9]/
I2STX_SDA/
MOSI1/MAT2[3]
P0[10]/TXD2/
SDA2/MAT3 [0]
P0[11]/RXD2/
SCL2/MAT3[1]
113[1]
112[1]
111[1]
109[1]
69[1]
70[1]
P0[12]/MISO1/
AD0[6]
29[2]
P0[13]/
USB_UP_LED2/
MOSI1/AD0[7]
32[2]
O
MAT2[2] — Match output for Timer 2, channel 2.
I/O
P0[9] — General purpose digital input/output pin.
I/O
I2STX_SDA — Transmit data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I2S-bus specification.
I/O
MOSI1 — Master Out Slave In for SSP1.
O
MAT2[3] — Match output for Timer 2, channel 3.
I/O
P0[10] — General purpose digital input/output pin.
O
TXD2 — Transmitter output for UART2.
I/O
SDA2 — I2C2 data input/output (this is not an open drain pin).
O
MAT3[0] — Match output for Timer 3, channel 0.
I/O
P0[11] — General purpose digital input/output pin.
I
RXD2 — Receiver input for UART2.
I/O
SCL2 — I2C2 clock input/output (this is not an open drain pin).
O
MAT3[1] — Match output for Timer 3, channel 1.
I/O
P0[12] — General purpose digital input/output pin.
I/O
MISO1 — Master In Slave Out for SSP1.
I
AD0[6] — A/D converter 0, input 6.
I/O
P0[13] — General purpose digital input/output pin.
O
USB_UP_LED2 — USB2 Good Link LED indicator. It is LOW when device is
configured (non-control endpoints enabled). It is HIGH when the device is not
configured or during global suspend.
I/O
MOSI1 — Master Out Slave In for SSP1.
I
AD0[7] — A/D converter 0, input 7.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
6 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
P0[14]/
48[1]
USB_CONNECT2/
SSEL1
P0[15]/TXD1/
SCK0/SCK
P0[16]/RXD1/
SSEL0/SSEL
P0[17]/CTS1/
MISO0/MISO
P0[18]/DCD1/
MOSI0/MOSI
P0[19]/DSR1/
MCICLK/SDA1
P0[20]/DTR1/
MCICMD/SCL1
P0[21]/RI1/
MCIPWR/RD1
P0[22]/RTS1/
MCIDAT0/TD1
P0[23]/AD0[0]/
I2SRX_CLK/
CAP3[0]
89[1]
90[1]
87[1]
86[1]
85[1]
83[1]
82[1]
80[1]
13[2]
Type
Description
I/O
P0[14] — General purpose digital input/output pin.
O
USB_CONNECT2 — USB2 Soft Connect control. Signal used to switch an external
1.5 kΩ resistor under software control. Used with the SoftConnect USB feature.
I/O
SSEL1 — Slave Select for SSP1.
I/O
P0[15] — General purpose digital input/output pin.
O
TXD1 — Transmitter output for UART1.
I/O
SCK0 — Serial clock for SSP0.
I/O
SCK — Serial clock for SPI.
I/O
P0 [16] — General purpose digital input/output pin.
I
RXD1 — Receiver input for UART1.
I/O
SSEL0 — Slave Select for SSP0.
I/O
SSEL — Slave Select for SPI.
I/O
P0[17] — General purpose digital input/output pin.
I
CTS1 — Clear to Send input for UART1.
I/O
MISO0 — Master In Slave Out for SSP0.
I/O
MISO — Master In Slave Out for SPI.
I/O
P0[18] — General purpose digital input/output pin.
I
DCD1 — Data Carrier Detect input for UART1.
I/O
MOSI0 — Master Out Slave In for SSP0.
I/O
MOSI — Master Out Slave In for SPI.
I/O
P0[19] — General purpose digital input/output pin.
I
DSR1 — Data Set Ready input for UART1.
O
MCICLK — Clock output line for SD/MMC interface.
I/O
SDA1 — I2C1 data input/output (this is not an open drain pin).
I/O
P0[20] — General purpose digital input/output pin.
O
DTR1 — Data Terminal Ready output for UART1.
I
MCICMD — Command line for SD/MMC interface.
I/O
SCL1 — I2C1 clock input/output (this is not an open drain pin).
I/O
P0[21] — General purpose digital input/output pin.
I
RI1 — Ring Indicator input for UART1.
O
MCIPWR — Power Supply Enable for external SD/MMC power supply.
I
RD1 — CAN1 receiver input.
I/O
P0[22] — General purpose digital input/output pin.
O
RTS1 — Request to Send output for UART1.
O
MCIDAT0 — Data line for SD/MMC interface.
O
TD1 — CAN1 transmitter output.
I/O
P0[23] — General purpose digital input/output pin.
I
AD0[0] — A/D converter 0, input 0.
I/O
I2SRX_CLK — Receive Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I2S-bus specification.
I
CAP3[0] — Capture input for Timer 3, channel 0.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
7 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P0[24]/AD0[1]/
I2SRX_WS/
CAP3[1]
11[3]
I/O
P0[24] — General purpose digital input/output pin.
I
AD0[1] — A/D converter 0, input 1.
I/O
I2SRX_WS — Receive Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I2S-bus specification.
I
CAP3[1] — Capture input for Timer 3, channel 1.
P0[25]/AD0[2]/
I2SRX_SDA/
TXD3
10[2]
I/O
P0[25] — General purpose digital input/output pin.
I
AD0[2] — A/D converter 0, input 2.
I/O
I2SRX_SDA — Receive data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I2S-bus specification.
O
TXD3 — Transmitter output for UART3.
P0[26]/AD0[3]/
AOUT/RXD3
8[2]
I/O
P0[26] — General purpose digital input/output pin.
I
AD0[3] — ]A/D converter 0, input 3.
O
AOUT — D/A converter output.
I
RXD3 — Receiver input for UART3.
I/O
P0[27] — General purpose digital input/output pin.
I/O
SDA0 — I2C0 data input/output. Open drain output (for I2C-bus compliance).
I/O
P0[28] — General purpose digital input/output pin.
I/O
SCL0 — I2C0 clock input/output. Open drain output (for I2C-bus compliance).
I/O
P0[29] — General purpose digital input/output pin.
I/O
USB_D+1 — USB1 port bidirectional D+ line.
I/O
P0[30] — General purpose digital input/output pin.
I/O
USB_D−1 — USB1 port bidirectional D− line.
I/O
P0[31] — General purpose digital input/output pin.
I/O
USB_D+2 — USB2 port bidirectional D+ line.
I/O
Port 1: Port 1 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 1 pins depends upon the pin function selected via the Pin Connect
block. Pins 2, 3, 5, 6, 7, 11, 12, and 13 of this port are not available.
I/O
P1[0] — General purpose digital input/output pin.
O
ENET_TXD0 — Ethernet transmit data 0.
I/O
P1[1] — General purpose digital input/output pin.
O
ENET_TXD1 — Ethernet transmit data 1.
I/O
P1[4] — General purpose digital input/output pin.
O
ENET_TX_EN — Ethernet transmit data enable.
I/O
P1[8] — General purpose digital input/output pin.
I
ENET_CRS — Ethernet carrier sense.
I/O
P1[9] — General purpose digital input/output pin.
I
ENET_RXD0 — Ethernet receive data.
I/O
P1[10] — General purpose digital input/output pin.
I
ENET_RXD1 — Ethernet receive data.
P0[27]/SDA0
P0[28]/SCL0
35[4]
34[4]
P0[29]/USB_D+1
42[5]
P0[30]/USB_D−1
43[5]
P0[31]/USB_D+2
36[5]
P1[0] to P1[31]
P1[0]/
ENET_TXD0
136[1]
P1[1]/
ENET_TXD1
135[1]
P1[4]/
ENET_TX_EN
133[1]
P1[8]/
ENET_CRS
132[1]
P1[9]/
ENET_RXD0
131[1]
P1[10]/
ENET_RXD1
129[1]
P1[14]/
ENET_RX_ER
128[1]
I/O
P1[14] — General purpose digital input/output pin.
I
ENET_RX_ER — Ethernet receive error.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
8 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P1[15]/
ENET_REF_CLK
126[1]
I/O
P1[15] — General purpose digital input/output pin.
I
ENET_REF_CLK/ENET_RX_CLK — Ethernet receiver clock.
P1[16]/
ENET_MDC
125[1]
I/O
P1[16] — General purpose digital input/output pin.
I
ENET_MDC — Ethernet MIIM clock.
P1[17]/
ENET_MDIO
123[1]
I/O
P1[17] — General purpose digital input/output pin.
I/O
ENET_MDIO — Ethernet MI data input and output.
P1[18]/
USB_UP_LED1/
PWM1[1]/
CAP1[0]
46[1]
I/O
P1[18] — General purpose digital input/output pin.
O
USB_UP_LED1 — USB1 port Good Link LED indicator. It is LOW when device is
configured (non-control endpoints enabled). It is HIGH when the device is not
configured or during global suspend.
O
PWM1[1] — Pulse Width Modulator 1, channel 1 output.
I
CAP1[0] — Capture input for Timer 1, channel 0.
I/O
P1[19] — General purpose digital input/output pin.
I
CAP1[1] — Capture input for Timer 1, channel 1.
I/O
P1[20] — General purpose digital input/output pin.
O
PWM1[2] — Pulse Width Modulator 1, channel 2 output.
I/O
SCK0 — Serial clock for SSP0.
I/O
P1[21] — General purpose digital input/output pin.
O
PWM1[3] — Pulse Width Modulator 1, channel 3 output.
I/O
SSEL0 — Slave Select for SSP0.
I/O
P1[22] — General purpose digital input/output pin.
O
MAT1[0] — Match output for Timer 1, channel 0.
I/O
P1[23] — General purpose digital input/output pin.
O
PWM1[4] — Pulse Width Modulator 1, channel 4 output.
I/O
MISO0 — Master In Slave Out for SSP0.
I/O
P1[24] — General purpose digital input/output pin.
O
PWM1[5] — Pulse Width Modulator 1, channel 5 output.
I/O
MOSI0 — Master Out Slave in for SSP0.
I/O
P1[25] — General purpose digital input/output pin.
O
MAT1[1] — Match output for Timer 1, channel 1.
I/O
P1[26] — General purpose digital input/output pin.
O
PWM1[6] — Pulse Width Modulator 1, channel 6 output.
I
CAP0[0] — Capture input for Timer 0, channel 0.
I/O
P1[27] — General purpose digital input/output pin.
I
CAP0[1] — Capture input for Timer 0, channel 1.
P1[19]/CAP1[1]
47[1]
P1[20]/PWM1[2]/
SCK0
49[1]
P1[21]/PWM1[3]/
SSEL0
50[1]
P1[22]/MAT1[0]
51[1]
P1[23]/PWM1[4]/
MISO0
53[1]
P1[24]/PWM1[5]/
MOSI0
54[1]
P1[25]/MAT1[1]
56[1]
P1[26]/PWM1[6]/
CAP0[0]
57[1]
P1[27]/CAP0[1]
61[1]
P1[28]/
PCAP1[0]/
MAT0[0]
63[1]
P1[29]/
PCAP1[1]/
MAT0[1]
64[1]
I/O
P1[28] — General purpose digital input/output pin.
I
PCAP1[0] — Capture input for PWM1, channel 0.
O
MAT0[0] — Match output for Timer 0, channel 0.
I/O
P1[29] — General purpose digital input/output pin.
I
PCAP1[1] — Capture input for PWM1, channel 1.
O
MAT0[1] — Match output for Timer 0, channel 0.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
9 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P1[30]/
VBUS/AD0[4]
30[2]
I/O
P1[30] — General purpose digital input/output pin.
I
VBUS — Indicates the presence of USB bus power.
Note: This signal must be HIGH for USB reset to occur.
P1[31]/SCK1/
AD0[5]
28[2]
P2[0] to P2[31]
P2[0]/PWM1[1]/
TXD1/
TRACECLK
107[1]
P2[1]/PWM1[2]/
RXD1/
PIPESTAT0
106[1]
P2[2]/PWM1[3]/
CTS1/
PIPESTAT1
105[1]
P2[3]/PWM1[4]/
DCD1/
PIPESTAT2
100[1]
P2[4]/PWM1[5]/
DSR1/
TRACESYNC
99[1]
P2[5]/PWM1[6]/
DTR1/
TRACEPKT0
97[1]
P2[6]/PCAP1[0]/
RI1/
TRACEPKT1
96[1]
I
AD0[4] — A/D converter 0, input 4.
I/O
P1[31] — General purpose digital input/output pin.
I/O
SCK1 — Serial Clock for SSP1.
I
AD0[5] — A/D converter 0, input 5.
I/O
Port 2: Port 2 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 2 pins depends upon the pin function selected via the Pin Connect
block. Pins 14 through 31 of this port are not available.
I/O
P2[0] — General purpose digital input/output pin.
O
PWM1[1] — Pulse Width Modulator 1, channel 1 output.
O
TXD1 — Transmitter output for UART1.
O
TRACECLK — Trace Clock.
I/O
P2[1] — General purpose digital input/output pin.
O
PWM1[2] — Pulse Width Modulator 1, channel 2 output.
I
RXD1 — Receiver input for UART1.
O
PIPESTAT0 — Pipeline Status, bit 0.
I/O
P2[2] — General purpose digital input/output pin.
O
PWM1[3] — Pulse Width Modulator 1, channel 3 output.
I
CTS1 — Clear to Send input for UART1.
O
PIPESTAT1 — Pipeline Status, bit 1.
I/O
P2[3] — General purpose digital input/output pin.
O
PWM1[4] — Pulse Width Modulator 1, channel 4 output.
I
DCD1 — Data Carrier Detect input for UART1.
O
PIPESTAT2 — Pipeline Status, bit 2.
I/O
P2[4] — General purpose digital input/output pin.
O
PWM1[5] — Pulse Width Modulator 1, channel 5 output.
I
DSR1 — Data Set Ready input for UART1.
O
TRACESYNC — Trace Synchronization.
I/O
P2[5] — General purpose digital input/output pin.
O
PWM1[6] — Pulse Width Modulator 1, channel 6 output.
O
DTR1 — Data Terminal Ready output for UART1.
O
TRACEPKT0 — Trace Packet, bit 0.
I/O
P2[6] — General purpose digital input/output pin.
I
PCAP1[0] — Capture input for PWM1, channel 0.
I
RI1 — Ring Indicator input for UART1.
O
TRACEPKT1 — Trace Packet, bit 1.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
10 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P2[7]/RD2/
RTS1/
TRACEPKT2
95[1]
I/O
P2[7] — General purpose digital input/output pin.
I
RD2 — CAN2 receiver input.
O
RTS1 — Request to Send output for UART1.
O
TRACEPKT2 — Trace Packet, bit 2.
P2[8]/TD2/
TXD2/
TRACEPKT3
93[1]
I/O
P2[8] — General purpose digital input/output pin.
O
TD2 — CAN2 transmitter output.
O
TXD2 — Transmitter output for UART2.
92[1]
P2[9]/
USB_CONNECT1/
RXD2/
EXTIN0
P2[10]/EINT0
76[6]
O
TRACEPKT3 — Trace Packet, bit 3.
I/O
P2[9] — General purpose digital input/output pin.
O
USB_CONNECT1 — USB1 Soft Connect control. Signal used to switch an external
1.5 kΩ resistor under the software control. Used with the SoftConnect USB feature.
I
RXD2 — Receiver input for UART2.
I
EXTIN0 — External Trigger Input.
I/O
P2[10] — General purpose digital input/output pin.
Note: LOW on this pin while RESET is LOW forces on-chip boot-loader to take over
control of the part after a reset.
P2[11]/EINT1/
MCIDAT1/
I2STX_CLK
P2[12]/EINT2/
MCIDAT2/
I2STX_WS
P2[13]/EINT3/
MCIDAT3/
I2STX_SDA
75[6]
73[6]
71[6]
P3[0] to P3[31]
P3[0]/D0
137[1]
P3[1]/D1
140[1]
P3[2]/D2
144[1]
P3[3]/D3
2[1]
I
EINT0 — External interrupt 0 input.
I/O
P2[11] — General purpose digital input/output pin.
I
EINT1 — External interrupt 1 input.
O
MCIDAT1 — Data line for SD/MMC interface.
I/O
I2STX_CLK — Transmit Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I2S-bus specification.
I/O
P2[12] — General purpose digital input/output pin.
I
EINT2 — External interrupt 2 input.
O
MCIDAT2 — Data line for SD/MMC interface.
I/O
I2STX_WS — Transmit Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I2S-bus specification.
I/O
P2[13] — General purpose digital input/output pin.
I
EINT3 — External interrupt 3 input.
O
MCIDAT3 — Data line for SD/MMC interface.
I/O
I2STX_SDA — Transmit data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I2S-bus specification.
I/O
Port 3: Port 3 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 3 pins depends upon the pin function selected via the Pin Connect
block. Pins 8 through 22, and 27 through 31 of this port are not available.
I/O
P3[0] — General purpose digital input/output pin.
I/O
D0 — External memory data line 0.
I/O
P3[1] — General purpose digital input/output pin.
I/O
D1 — External memory data line 1.
I/O
P3[2] — General purpose digital input/output pin.
I/O
D2 — External memory data line 2.
I/O
P3[3] — General purpose digital input/output pin.
I/O
D3 — External memory data line 3.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
11 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P3[4]/D4
9[1]
I/O
P3[4] — General purpose digital input/output pin.
I/O
D4 — External memory data line 4.
P3[5]/D5
12[1]
I/O
P3[5] — General purpose digital input/output pin.
I/O
D5 — External memory data line 5.
P3[6]/D6
16[1]
I/O
P3[6] — General purpose digital input/output pin.
I/O
D6 — External memory data line 6.
P3[7]/D7
19[1]
I/O
P3[7] — General purpose digital input/output pin.
I/O
D7 — External memory data line 7.
P3[23]/CAP0[0]/
PCAP1[0]
45[1]
I/O
P3[23] — General purpose digital input/output pin.
I
CAP0[0] — Capture input for Timer 0, channel 0.
I
PCAP1[0] — Capture input for PWM1, channel 0.
P3[24]/CAP0[1]/
PWM1[1]
40[1]
P3[25]/MAT0[0]/
PWM1[2]
39[1]
P3[26]/MAT0[1]/
PWM1[3]
38[1]
P4[0] to P4[31]
P4[0]/A0
52[1]
P4[1]/A1
55[1]
P4[2]/A2
58[1]
P4[3]/A3
68[1]
P4[4]/A4
72[1]
P4[5]/A5
74[1]
P4[6]/A6
78[1]
P4[7]/A7
84[1]
P4[8]/A8
88[1]
I/O
P3[24] — General purpose digital input/output pin.
I
CAP0[1] — Capture input for Timer 0, channel 1.
O
PWM1[1] — Pulse Width Modulator 1, output 1.
I/O
P3[25] — General purpose digital input/output pin.
O
MAT0[0] — Match output for Timer 0, channel 0.
O
PWM1[2] — Pulse Width Modulator 1, output 2.
I/O
P3[26] — General purpose digital input/output pin.
O
MAT0[1] — Match output for Timer 0, channel 1.
O
PWM1[3] — Pulse Width Modulator 1, output 3.
I/O
Port 4: Port 4 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 4 pins depends upon the pin function selected via the Pin Connect
block. Pins 16 through 23, 26, and 27 of this port are not available.
I/O
P4[0] — ]General purpose digital input/output pin.
I/O
A0 — External memory address line 0.
I/O
P4[1] — General purpose digital input/output pin.
I/O
A1 — External memory address line 1.
I/O
P4[2] — General purpose digital input/output pin.
I/O
A2 — External memory address line 2.
I/O
P4[3] — General purpose digital input/output pin.
I/O
A3 — External memory address line 3.
I/O
P4[4] — General purpose digital input/output pin.
I/O
A4 — External memory address line 4.
I/O
P4[5] — General purpose digital input/output pin.
I/O
A5 — External memory address line 5.
I/O
P4[6] — General purpose digital input/output pin.
I/O
A6 — External memory address line 6.
I/O
P4[7] — General purpose digital input/output pin.
I/O
A7 — External memory address line 7.
I/O
P4[8] — General purpose digital input/output pin.
I/O
A8 — External memory address line 8.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
12 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
P4[9]/A9
91[1]
I/O
P4[9] — General purpose digital input/output pin.
I/O
A9 — External memory address line 9.
P4[10]/A10
94[1]
I/O
P4[10] — General purpose digital input/output pin.
I/O
A10 — External memory address line 10.
P4[11]/A11
101[1]
I/O
P4[11] — General purpose digital input/output pin.
I/O
A11 — External memory address line 11.
P4[12]/A12
104[1]
I/O
P4[12] — General purpose digital input/output pin.
I/O
A12 — External memory address line 12.
P4[13]/A13
108[1]
I/O
P4[13] — General purpose digital input/output pin.
I/O
A13 — External memory address line 13.
P4[14]/A14
110[1]
I/O
P4[14] — General purpose digital input/output pin.
I/O
A14 — External memory address line 14.
P4[15]/A15
120[1]
I/O
P4[15] — General purpose digital input/output pin.
I/O
A15 — External memory address line 15.
P4[24]/OE
127[1]
I/O
P4[24] — General purpose digital input/output pin.
O
OE — LOW active Output Enable signal.
P4[25]/WE
124[1]
I/O
P4[25] — General purpose digital input/output pin.
O
WE — LOW active Write Enable signal.
P4[28]/MAT2[0]/
TXD3
118[1]
I/O
P4 [28] — General purpose digital input/output pin.
O
MAT2[0] — Match output for Timer 2, channel 0.
O
TXD3 — Transmitter output for UART3.
I/O
P4[29] — General purpose digital input/output pin.
O
MAT2[1] — Match output for Timer 2, channel 1.
I
RXD3 — Receiver input for UART3.
I/O
P4[30] — General purpose digital input/output pin.
O
CS0 — LOW active Chip Select 0 signal.
I/O
P4[31] — General purpose digital input/output pin.
P4[29]/MAT2[1]/
RXD3
122[1]
P4[30]/CS0
130[1]
P4[31]/CS1
134[1]
O
CS1 — LOW active Chip Select 1 signal.
ALARM
26[8]
O
ALARM — RTC controlled output. This is a 1.8 V pin. It goes HIGH when a RTC
alarm is generated.
USB_D−2
37
I/O
USB_D−2 — USB2 port bidirectional D− line.
DBGEN
6[1]
I
DBGEN — JTAG interface control signal. Also used for boundary scanning.
TDO
1[1]
O
TDO — Test Data out for JTAG interface.
TDI
3[1]
I
TDI — Test Data in for JTAG interface.
TMS
4[1]
I
TMS — Test Mode Select for JTAG interface.
TRST
5[1]
I
TRST — Test Reset for JTAG interface.
TCK
7[1]
I
TCK — Test Clock for JTAG interface.
RTCK
143[1]
I/O
RTCK — JTAG interface control signal.
Note: LOW on this pin while RESET is LOW enables ETM pins (P2[9:0]) to operate
as Trace port after reset.
RSTOUT
20[1]
O
RSTOUT — This is a 1.8 V pin. LOW on this pin indicates LPC2378 being in Reset
state.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
13 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 3.
Pin description …continued
Symbol
Pin
Type
Description
RESET
24[7]
I
external reset input: A LOW on this pin resets the device, causing I/O ports and
peripherals to take on their default states, and processor execution to begin at
address 0. TTL with hysteresis, 5 V tolerant.
XTAL1
31[8]
I
Input to the oscillator circuit and internal clock generator circuits.
XTAL2
33[8]
O
Output from the oscillator amplifier.
RTCX1
23[8]
I
Input to the RTC oscillator circuit.
RTCX2
25[8]
O
Output from the RTC oscillator circuit.
VSS
22, 44,
I
59, 65,
79, 103,
117,119,
139[9]
ground: 0 V reference.
VSSA
15[10]
analog ground: 0 V reference. This should nominally be the same voltage as VSS,
but should be isolated to minimize noise and error.
VDD(3V3)
41, 62,
I
77, 102,
114,
138[11]
3.3 V supply voltage: This is the power supply voltage for the I/O ports.
VDD(1V8)
21, 81,
98[12]
I
1.8 V supply voltage: This is the power supply voltage for the core. If these pins are
left floating, the on-chip DC-to-DC converter will generate 1.8 V out of power
VDCDC(3V3) supply. Having these pins tied to an externally supplied 1.8 V will turn off
the on-chip DC-to-DC converter resulting in lower current consumption when in low
power mode.
VDD(DCDC)(3V3)
18, 60,
121[13]
I
3.3 V DC-to-DC converter supply voltage: This is the power supply for the on-chip
DC-to-DC converter only. If the DC-to-DC is not used, these pins must be left
unconnected.
VDDA
14[14]
I
analog 3.3 V pad supply voltage: This should be nominally the same voltage as
VDD(3V3) but should be isolated to minimize noise and error. This voltage is used to
power the ADC and DAC.
VREF
17[14]
I
ADC reference: This should be nominally the same voltage as VDD(3V3) but should
be isolated to minimize noise and error. The level on this pin is used as a reference
for ADC and DAC.
VBAT
27[14]
I
RTC power supply: 3.3 V on this pin supplies the power to the RTC.
I
[1]
5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis.
[2]
5 V tolerant pad providing digital I/O functions (with TTL levels and hysteresis) and analog input. When configured as a DAC input,
digital section of the pad is disabled.
[3]
5 V tolerant pad providing digital I/O with TTL levels and hysteresis and analog output function. When configured as the DAC output,
digital section of the pad is disabled.
[4]
Open drain 5 V tolerant digital I/O I2C-bus 400 kHz specification compatible pad. It requires an external pull-up to provide output
functionality. When power is switched off, this pin connected to the I2C-bus is floating and does not disturb the I2C lines.
[5]
Pad provides digital I/O and USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and
Low-speed mode only).
[6]
5 V tolerant pad with 5 ns glitch filter providing digital I/O functions with TTL levels and hysteresis.
[7]
5 V tolerant pad with 20 ns glitch filter providing digital I/O function with TTL levels and hysteresis.
[8]
Pad provides special analog functionality.
[9]
Pad provides special analog functionality.
[10] Pad provides special analog functionality.
[11] Pad provides special analog functionality.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
14 of 54
LPC2378
NXP Semiconductors
Fast communication chip
[12] Pad provides special analog functionality.
[13] Pad provides special analog functionality.
[14] Pad provides special analog functionality.
7. Functional description
7.1 Architectural overview
The LPC2378 microcontroller consists of an ARM7TDMI-S CPU with emulation support,
the ARM7 local bus for closely coupled, high speed access to the majority of on-chip
memory, the AMBA AHB interfacing to high speed on-chip peripherals and external
memory, and the AMBA APB for connection to other on-chip peripheral functions. The
microcontroller permanently configures the ARM7TDMI-S processor for little-endian byte
order.
The LPC2378 implements two AHB buses in order to allow the Ethernet block to operate
without interference caused by other system activity. The primary AHB, referred to as
AHB1, includes the VIC, GPDMA controller, and EMC.
The second AHB, referred to as AHB2, includes only the Ethernet block and an
associated 16 kB SRAM. In addition, a bus bridge is provided that allows the secondary
AHB to be a bus master on AHB1, allowing expansion of Ethernet buffer space into
off-chip memory or unused space in memory residing on AHB1.
In summary, bus masters with access to AHB1 are the ARM7 itself, the GPDMA function,
and the Ethernet block (via the bus bridge from AHB2). Bus masters with access to AHB2
are the ARM7 and the Ethernet block.
AHB peripherals are allocated a 2 MB range of addresses at the very top of the 4 GB
ARM memory space. Each AHB peripheral is allocated a 16 kB address space within the
AHB address space. Lower speed peripheral functions are connected to the APB bus.
The AHB to APB bridge interfaces the APB bus to the AHB bus. APB peripherals are also
allocated a 2 MB range of addresses, beginning at the 3.5 GB address point. Each APB
peripheral is allocated a 16 kB address space within the APB address space.
The ARM7TDMI-S processor is a general purpose 32-bit microprocessor, which offers
high performance and very low power consumption. The ARM architecture is based on
Reduced Instruction Set Computer (RISC) principles, and the instruction set and related
decode mechanism are much simpler than those of microprogrammed complex
instruction set computers. This simplicity results in a high instruction throughput and
impressive real-time interrupt response from a small and cost-effective processor core.
Pipeline techniques are employed so that all parts of the processing and memory systems
can operate continuously. Typically, while one instruction is being executed, its successor
is being decoded, and a third instruction is being fetched from memory.
The ARM7TDMI-S processor also employs a unique architectural strategy known as
Thumb, which makes it ideally suited to high-volume applications with memory
restrictions, or applications where code density is an issue.
The key idea behind Thumb is that of a super-reduced instruction set. Essentially, the
ARM7TDMI-S processor has two instruction sets:
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
15 of 54
LPC2378
NXP Semiconductors
Fast communication chip
• the standard 32-bit ARM set
• a 16-bit Thumb set
The Thumb set’s 16-bit instruction length allows it to approach twice the density of
standard ARM code while retaining most of the ARM’s performance advantage over a
traditional 16-bit processor using 16-bit registers. This is possible because Thumb code
operates on the same 32-bit register set as ARM code.
Thumb code is able to provide up to 65 % of the code size of ARM, and 160 % of the
performance of an equivalent ARM processor connected to a 16-bit memory system.
7.2 On-chip flash programming memory
The LPC2378 incorporates 512 kB flash memory system. This memory may be used for
both code and data storage. Programming of the flash memory may be accomplished in
several ways. It may be programmed In System via the serial port (UART0). The
application program may also erase and/or program the flash while the application is
running, allowing a great degree of flexibility for data storage field and firmware upgrades.
The flash memory is 128 bits wide and includes pre-fetching and buffering techniques to
allow it to operate at SRAM speeds of 72 MHz.
The LPC2378 provides a minimum of 100000 write/erase cycles and 20 years of data
retention.
7.3 On-chip SRAM
The LPC2378 includes a SRAM memory of 32 kB reserved for the ARM processor
exclusive use. This RAM may be used for code and/or data storage and may be accessed
as 8 bits, 16 bits, and 32 bits.
A 16 kB SRAM block serving as a buffer for the Ethernet controller and an 8 kB SRAM
associated with the USB device can be used both for data and code storage, too.
Remaining SRAM such as a 4 kB USB FIFO and a 2 kB RTC SRAM can be used for data
storage only. The RTC SRAM is battery powered and retains the content in the absence of
the main power supply.
7.4 Memory map
The LPC2378 memory map incorporates several distinct regions as shown in Figure 3.
In addition, the CPU interrupt vectors may be remapped to allow them to reside in either
flash memory (default), boot ROM, or SRAM (see Section 7.26.6).
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
16 of 54
LPC2378
NXP Semiconductors
Fast communication chip
4.0 GB
0xFFFF FFFF
AHB PERIPHERALS
0xF000 0000
3.75 GB
APB PERIPHERALS
3.5 GB
0xE000 0000
RESERVED ADDRESS SPACE
3.0 GB
0xC000 0000
0x8100 FFFF
EXTERNAL MEMORY BANK 1 (64 kB)
0x8100 0000
0x8000 FFFF
EXTERNAL MEMORY BANK 0 (64 kB)
2.0 GB
0x8000 0000
BOOT ROM AND BOOT FLASH
(BOOT FLASH REMAPPED FROM ON-CHIP FLASH)
RESERVED ADDRESS SPACE
0x7FE0 3FFF
0x7FE0 0000
ETHERNET RAM (16 kB)
0x7FD0 1FFF
USB RAM (8 kB)
0x7FD0 0000
RESERVED ADDRESS SPACE
0x4000 8000
0x4000 7FFF
32 kB LOCAL ON-CHIP STATIC RAM
1.0 GB
0x4000 0000
RESERVED ADDRESS SPACE
0x0008 0000
0x0007 FFFF
TOTAL OF 512 kB ON-CHIP NON-VOLATILE MEMORY
0.0 GB
0x0000 0000
002aac585
Fig 3. LPC2378 memory map
7.5 Interrupt controller
The ARM processor core has two interrupt inputs called Interrupt Request (IRQ) and Fast
Interrupt Request (FIQ). The VIC takes 32 interrupt request inputs which can be
programmed as FIQ or vectored IRQ types. The programmable assignment scheme
means that priorities of interrupts from the various peripherals can be dynamically
assigned and adjusted.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
17 of 54
LPC2378
NXP Semiconductors
Fast communication chip
FIQs have the highest priority. If more than one request is assigned to FIQ, the VIC ORs
the requests to produce the FIQ signal to the ARM processor. The fastest possible FIQ
latency is achieved when only one request is classified as FIQ, because then the FIQ
service routine can simply start dealing with that device. But if more than one request is
assigned to the FIQ class, the FIQ service routine can read a word from the VIC that
identifies which FIQ source(s) is (are) requesting an interrupt.
Vectored IRQs, which include all interrupt requests that are not classified as FIQs, have a
programmable interrupt priority. When more than one interrupt is assigned the same
priority and occur simultaneously, the one connected to the lowest numbered VIC channel
will be serviced first.
The VIC ORs the requests from all of the vectored IRQs to produce the IRQ signal to the
ARM processor. The IRQ service routine can start by reading a register from the VIC and
jumping to the address supplied by that register.
7.5.1 Interrupt sources
Each peripheral device has one interrupt line connected to the VIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any pin on PORT0 and PORT2 (total of 46 pins) regardless of the selected function, can
be programmed to generate an interrupt on a rising edge, a falling edge, or both. Such
interrupt request coming from PORT0 and/or PORT2 will be combined with the EINT3
interrupt requests.
7.6 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.7 External memory controller
The LPC2378 EMC is an ARM PrimeCell MultiPort Memory Controller peripheral offering
support for asynchronous static memory devices such as RAM, ROM, and flash. In
addition, it can be used as an interface with off-chip memory-mapped devices and
peripherals. The EMC is an Advanced Microcontroller Bus Architecture (AMBA) compliant
peripheral.
7.7.1 Features
• Asynchronous static memory device support including RAM, ROM, and flash, with or
without asynchronous page mode
•
•
•
•
Low transaction latency
Read and write buffers to reduce latency and to improve performance
8 data and 16 address lines wide static memory support
Two chip selects for static memory devices
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
18 of 54
LPC2378
NXP Semiconductors
Fast communication chip
• Static memory features include:
– Asynchronous page mode read
– Programmable Wait States (WST)
– Bus turnaround delay
– Output enable and write enable delays
– Extended wait
7.8 General purpose DMA controller
The GPDMA is an AMBA AHB compliant peripheral allowing selected LPC2378
peripherals to have DMA support.
The GPDMA enables peripheral-to-memory, memory-to-peripheral,
peripheral-to-peripheral, and memory-to-memory transactions. Each DMA stream
provides unidirectional serial DMA transfers for a single source and destination. For
example, a bidirectional port requires one stream for transmit and one for receive. The
source and destination areas can each be either a memory region or a peripheral, and
can be accessed through the AHB master.
7.8.1 Features
• Two DMA channels. Each channel can support a unidirectional transfer.
• The GPDMA can transfer data between the 8 kB SRAM and peripherals such as the
SD/MMC, two SSP, and I2S interfaces.
• Single DMA and burst DMA request signals. Each peripheral connected to the
GPDMA can assert either a burst DMA request or a single DMA request. The DMA
burst size is set by programming the GPDMA.
• Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and
peripheral-to-peripheral transfers.
• Scatter or gather DMA is supported through the use of linked lists. This means that
the source and destination areas do not have to occupy contiguous areas of memory.
• Hardware DMA channel priority. Each DMA channel has a specific hardware priority.
DMA channel 0 has the highest priority and channel 1 has the lowest priority. If
requests from two channels become active at the same time, the channel with the
highest priority is serviced first.
• AHB slave DMA programming interface. The GPDMA is programmed by writing to the
DMA control registers over the AHB slave interface.
• One AHB bus master for transferring data. This interface transfers data when a DMA
request goes active.
• 32-bit AHB master bus width.
• Incrementing or non-incrementing addressing for source and destination.
• Programmable DMA burst size. The DMA burst size can be programmed to more
efficiently transfer data. Usually the burst size is set to half the size of the FIFO in the
peripheral.
• Internal four-word FIFO per channel.
• Supports 8-bit, 16-bit, and 32-bit wide transactions.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
19 of 54
LPC2378
NXP Semiconductors
Fast communication chip
• An interrupt to the processor can be generated on a DMA completion or when a DMA
error has occurred.
• Interrupt masking. The DMA error and DMA terminal count interrupt requests can be
masked.
• Raw interrupt status. The DMA error and DMA count raw interrupt status can be read
prior to masking.
7.9 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back as well as the current state of the port pins.
LPC2378 use accelerated GPIO functions:
• GPIO registers are relocated to the ARM local bus so that the fastest possible I/O
timing can be achieved.
• Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
• All GPIO registers are byte and half-word addressable.
• Entire port value can be written in one instruction.
Additionally, any pin on PORT0 and PORT2 (total of 46 pins) providing a digital function
can be programmed to generate an interrupt on a rising edge, a falling edge, or both. The
edge detection is asynchronous, so it may operate when clocks are not present such as
during Power-down mode. Each enabled interrupt can be used to wake up the chip from
Power-down mode.
7.9.1 Features
• Bit level set and clear registers allow a single instruction to set or clear any number of
bits in one port.
• Direction control of individual bits.
• All I/O default to inputs after reset.
• Backward compatibility with other earlier devices is maintained with legacy PORT0
and PORT1 registers appearing at the original addresses on the APB bus.
7.10 Ethernet
The Ethernet block contains a full featured 10 Mbit/s or 100 Mbit/s Ethernet MAC
designed to provide optimized performance through the use of DMA hardware
acceleration. Features include a generous suite of control registers, half or full duplex
operation, flow control, control frames, hardware acceleration for transmit retry, receive
packet filtering and wake-up on LAN activity. Automatic frame transmission and reception
with scatter-gather DMA off-loads many operations from the CPU.
The Ethernet block and the CPU share a dedicated AHB subsystem that is used to access
the Ethernet SRAM for Ethernet data, control, and status information. All other AHB traffic
in the LPC2378 takes place on a different AHB subsystem, effectively separating Ethernet
activity from the rest of the system. The Ethernet DMA can also access off-chip memory
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
20 of 54
LPC2378
NXP Semiconductors
Fast communication chip
via the EMC, as well as the SRAM located on another AHB, if it is not being used by the
USB block. However, using memory other than the Ethernet SRAM, especially off-chip
memory, will slow Ethernet access to memory and increase the loading of its AHB.
The Ethernet block interfaces between an off-chip Ethernet PHY using the Reduced MII
(RMII) protocol and the on-chip Media Independent Interface Management (MIIM) serial
bus.
7.10.1 Features
• Ethernet standards support:
– Supports 10 Mbit/s or 100 Mbit/s PHY devices including 10 Base-T, 100 Base-TX,
100 Base-FX, and 100 Base-T4.
– Fully compliant with IEEE standard 802.3.
– Fully compliant with 802.3x Full Duplex Flow Control and Half Duplex back
pressure.
– Flexible transmit and receive frame options.
– Virtual Local Area Network (VLAN) frame support.
• Memory management:
– Independent transmit and receive buffers memory mapped to shared SRAM.
– DMA managers with scatter/gather DMA and arrays of frame descriptors.
– Memory traffic optimized by buffering and pre-fetching.
• Enhanced Ethernet features:
– Receive filtering.
– Multicast and broadcast frame support for both transmit and receive.
– Optional automatic Frame Check Sequence (FCS) insertion with Circular
Redundancy Check (CRC) for transmit.
– Selectable automatic transmit frame padding.
– Over-length frame support for both transmit and receive allows any length frames.
– Promiscuous receive mode.
– Automatic collision back-off and frame retransmission.
– Includes power management by clock switching.
– Wake-on-LAN power management support allows system wake-up: using the
receive filters or a magic frame detection filter.
• Physical interface:
– Attachment of external PHY chip through standard RMII interface.
– PHY register access is available via the MIIM interface.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
21 of 54
LPC2378
NXP Semiconductors
Fast communication chip
7.11 USB interface
The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a
host and a number (127 maximum) of peripherals. The host controller allocates the USB
bandwidth to attached devices through a token based protocol. The bus supports hot
plugging, unplugging and dynamic configuration of the devices. All transactions are
initiated by the host controller.
The two sets of pins needed by a USB device are named VBUS, USB_D+1, USB_D−1,
USB_UP_LED1, USB_CONNECT1, and USB_D+2, USB_D−2, USB_UP_LED2, and
USB_CONNECT2 respectively. At any given time only one of these two sets can be active
and used by the application.
7.11.1 USB device controller
The device controller enables 12 Mbit/s data exchange with a USB host controller. It
consists of register interface, serial interface engine, endpoint buffer memory, and the
DMA controller. The serial interface engine decodes the USB data stream and writes data
to the appropriate end point buffer memory. The status of a completed USB transfer or
error condition is indicated via status registers. An interrupt is also generated if enabled.
The DMA controller when enabled transfers data between the endpoint buffer and the
USB RAM.
7.11.1.1
Features
•
•
•
•
•
Fully compliant with USB 2.0 specification (full speed).
Supports 32 physical (16 logical) endpoints with a 4 kB USB buffer.
Supports Control, Bulk, Interrupt and Isochronous endpoints.
Scalable realization of endpoints at run time.
Endpoint Maximum packet size selection (up to USB maximum specification) by
software at run time.
• Supports SoftConnect and GoodLink features.
• While USB is in the Suspend mode, LPC2378 can enter one of the reduced power
down modes and wake up on a USB activity.
• Supports DMA transfers with the DMA RAM of 8 kB on all non-control endpoints.
• Allows dynamic switching between CPU-controlled and DMA modes.
• Double buffer implementation for Bulk and Isochronous endpoints.
7.12 CAN controller and acceptance filters
The Controller Area Network (CAN) is a serial communications protocol which efficiently
supports distributed real-time control with a very high level of security. Its domain of
application ranges from high speed networks to low cost multiplex wiring.
The CAN block is intended to support multiple CAN buses simultaneously, allowing the
device to be used as a gateway, switch, or router among a number of CAN buses in
industrial or automotive applications.
Each CAN controller has a register structure similar to the NXP SJA1000 and the PeliCAN
Library block, but the 8-bit registers of those devices have been combined in 32-bit words
to allow simultaneous access in the ARM environment. The main operational difference is
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
22 of 54
LPC2378
NXP Semiconductors
Fast communication chip
that the recognition of received Identifiers, known in CAN terminology as Acceptance
Filtering, has been removed from the CAN controllers and centralized in a global
Acceptance Filter.
7.12.1 Features
•
•
•
•
•
Two CAN controllers and buses.
Data rates to 1 Mbit/s on each bus.
32-bit register and RAM access.
Compatible with CAN specification 2.0B, ISO 11898-1.
Global Acceptance Filter recognizes 11-bit and 29-bit receive identifiers for all CAN
buses.
• Acceptance Filter can provide FullCAN-style automatic reception for selected
Standard Identifiers.
• Full CAN messages can generate interrupts.
7.13 10-bit ADC
The LPC2378 contains one ADC. It is a single 10-bit successive approximation ADC with
eight channels.
7.13.1 Features
•
•
•
•
•
•
•
•
10-bit successive approximation ADC
Input multiplexing among 8 pins
Power-down mode
Measurement range 0 V to Vi(VREF)
10-bit conversion time ≥ 2.44 µs
Burst conversion mode for single or multiple inputs
Optional conversion on transition of input pin or Timer Match signal
Individual result registers for each ADC channel to reduce interrupt overhead
7.14 10-bit DAC
The DAC allows the LPC2378 to generate a variable analog output. The maximum output
value of the DAC is Vi(VREF).
7.14.1 Features
•
•
•
•
•
10-bit DAC
Resistor string architecture
Buffered output
Power-down mode
Selectable output drive
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
23 of 54
LPC2378
NXP Semiconductors
Fast communication chip
7.15 UARTs
The LPC2378 contains four UARTs. In addition to standard transmit and receive data
lines, UART1 also provides a full modem control handshake interface.
The UARTs include a fractional baud rate generator. Standard baud rates such as 115200
can be achieved with any crystal frequency above 2 MHz.
7.15.1 Features
•
•
•
•
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
• UART1 equipped with standard modem interface signals. This module also provides
full support for hardware flow control (auto-CTS/RTS).
• UART3 includes an IrDA mode to support infrared communication.
7.16 SPI serial I/O controller
The LPC2378 contains one SPI controller. SPI is a full duplex serial interface designed to
handle multiple masters and slaves connected to a given bus. Only a single master and a
single slave can communicate on the interface during a given data transfer. During a data
transfer the master always sends 8 bits to 16 bits of data to the slave, and the slave
always sends 8 bits to 16 bits of data to the master.
7.16.1 Features
•
•
•
•
•
Compliant with SPI specification
Synchronous, Serial, Full Duplex Communication
Combined SPI master and slave
Maximum data bit rate of one eighth of the input clock rate
8 bits to 16 bits per transfer
7.17 SSP serial I/O controller
The LPC2378 contains two SSP controllers. The SSP controller is capable of operation on
a SPI, 4-wire SSI, or Microwire bus. It can interact with multiple masters and slaves on the
bus. Only a single master and a single slave can communicate on the bus during a given
data transfer. The SSP supports full duplex transfers, with frames of 4 bits to 16 bits of
data flowing from the master to the slave and from the slave to the master. In practice,
often only one of these data flows carries meaningful data.
7.17.1 Features
• Compatible with Motorola SPI, 4-wire TI SSI, and National Semiconductor Microwire
buses
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
24 of 54
LPC2378
NXP Semiconductors
Fast communication chip
•
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
DMA transfers supported by GPDMA
7.18 SD/MMC card interface
The Secure Digital and Multimedia Card Interface (MCI) allows access to external SD
memory cards. The SD card interface conforms to the SD Multimedia Card Specification
Version 2.11.
7.18.1 Features
• The MCI interface provides all functions specific to the SD/MMC memory card. These
include the clock generation unit, power management control, and command and data
transfer.
• Conforms to Multimedia Card Specification v2.11.
• Conforms to Secure Digital Memory Card Physical Layer Specification, v0.96.
• Can be used as a multimedia card bus or a secure digital memory card bus host. The
SD/MMC can be connected to several multimedia cards or a single secure digital
memory card.
• DMA supported through the GPDMA controller.
7.19 I2C-bus serial I/O controllers
The LPC2378 contains three I2C-bus controllers.
The I2C-bus is bidirectional, for inter-IC control using only two wires: a serial clock line
(SCL), and a serial data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C-bus is a multi-master bus and can
be controlled by more than one bus master connected to it.
The I2C-bus implemented in LPC2378 supports bit rates up to 400 kbit/s (Fast I2C-bus).
7.19.1 Features
• I2C0 is a standard I2C compliant bus interface with open-drain pins.
• I2C1 and I2C2 use standard I/O pins and do not support powering off of individual
devices connected to the same bus lines.
•
•
•
•
•
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
25 of 54
LPC2378
NXP Semiconductors
Fast communication chip
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus can be used for test and diagnostic purposes.
7.20 I2S-bus serial I/O controllers
The I2S-bus provides a standard communication interface for digital audio applications.
The I2S-bus specification defines a 3-wire serial bus using one data line, one clock line,
and one word select signal. The basic I2S connection has one master, which is always the
master, and one slave. The I2S interface on the LPC2378 provides a separate transmit
and receive channel, each of which can operate as either a master or a slave.
7.20.1 Features
• The interface has separate input/output channels each of which can operate in master
or slave mode.
• Capable of handling 8-bit, 16-bit, and 32-bit word sizes.
• Mono and stereo audio data supported.
• The sampling frequency can range from 16 kHz to 48 kHz ((16, 22.05, 32, 44.1,
48) kHz).
•
•
•
•
Configurable word select period in master mode (separately for I2S input and output).
Two 8 word FIFO data buffers are provided, one for transmit and one for receive.
Generates interrupt requests when buffer levels cross a programmable boundary.
Two DMA requests, controlled by programmable buffer levels. These are connected to
the GPDMA block.
• Controls include reset, stop and mute options separately for I2S input and I2S output.
7.21 General purpose 32-bit timers/external event counters
The LPC2378 includes four 32-bit Timer/Counters. The Timer/Counter is designed to
count cycles of the system derived clock or an externally-supplied clock. It can optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. The Timer/Counter also includes four capture inputs to trap the timer
value when an input signal transitions, optionally generating an interrupt.
7.21.1 Features
• A 32-bit Timer/Counter with a programmable 32-bit prescaler.
• Counter or Timer operation.
• Up to four 32-bit capture channels per timer, that can take a snapshot of the timer
value when an input signal transitions. A capture event may also optionally generate
an interrupt.
• Four 32-bit match registers that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
26 of 54
LPC2378
NXP Semiconductors
Fast communication chip
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
7.22 Pulse width modulator
The PWM is based on the standard Timer block and inherits all of its features, although
only the PWM function is pinned out on the LPC2378. The Timer is designed to count
cycles of the system derived clock and optionally switch pins, generate interrupts or
perform other actions when specified timer values occur, based on seven match registers.
The PWM function is in addition to these features, and is based on match register events.
The ability to separately control rising and falling edge locations allows the PWM to be
used for more applications. For instance, multi-phase motor control typically requires three
non-overlapping PWM outputs with individual control of all three pulse widths and
positions.
Two match registers can be used to provide a single edge controlled PWM output. One
match register (PWMMR0) controls the PWM cycle rate, by resetting the count upon
match. The other match register controls the PWM edge position. Additional single edge
controlled PWM outputs require only one match register each, since the repetition rate is
the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a
rising edge at the beginning of each PWM cycle, when an PWMMR0 match occurs.
Three match registers can be used to provide a PWM output with both edges controlled.
Again, the PWMMR0 match register controls the PWM cycle rate. The other match
registers control the two PWM edge positions. Additional double edge controlled PWM
outputs require only two match registers each, since the repetition rate is the same for all
PWM outputs.
With double edge controlled PWM outputs, specific match registers control the rising and
falling edge of the output. This allows both positive going PWM pulses (when the rising
edge occurs prior to the falling edge), and negative going PWM pulses (when the falling
edge occurs prior to the rising edge).
7.22.1 Features
• LPC2378 has one PWM block with Counter or Timer operation (may use the
peripheral clock or one of the capture inputs as the clock source).
• Seven match registers allow up to 6 single edge controlled or 3 double edge
controlled PWM outputs, or a mix of both types. The match registers also allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
27 of 54
LPC2378
NXP Semiconductors
Fast communication chip
• Supports single edge controlled and/or double edge controlled PWM outputs. Single
edge controlled PWM outputs all go high at the beginning of each cycle unless the
output is a constant low. Double edge controlled PWM outputs can have either edge
occur at any position within a cycle. This allows for both positive going and negative
going pulses.
• Pulse period and width can be any number of timer counts. This allows complete
flexibility in the trade-off between resolution and repetition rate. All PWM outputs will
occur at the same repetition rate.
• Double edge controlled PWM outputs can be programmed to be either positive going
or negative going pulses.
• Match register updates are synchronized with pulse outputs to prevent generation of
erroneous pulses. Software must ‘release’ new match values before they can become
effective.
• May be used as a standard timer if the PWM mode is not enabled.
• A 32-bit Timer/Counter with a programmable 32-bit Prescaler.
7.23 Watchdog timer
The purpose of the watchdog is to reset the microcontroller within a reasonable amount of
time if it enters an erroneous state. When enabled, the watchdog will generate a system
reset if the user program fails to ‘feed’ (or reload) the watchdog within a predetermined
amount of time.
7.23.1 Features
• Internally resets chip if not periodically reloaded.
• Debug mode.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect/Incomplete feed sequence causes reset/interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 32-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK) × 256 × 4) to (Tcy(WDCLK) × 232 × 4) in
multiples of Tcy(WDCLK) × 4.
• The Watchdog Clock (WDCLK) source can be selected from the RTC clock, the
Internal RC oscillator (IRC), or the APB peripheral clock. This gives a wide range of
potential timing choices of Watchdog operation under different power reduction
conditions. It also provides the ability to run the WDT from an entirely internal source
that is not dependent on an external crystal and its associated components and
wiring, for increased reliability.
7.24 RTC and battery RAM
The RTC is a set of counters for measuring time when system power is on, and optionally
when it is off. It uses little power in Power-down mode. On the LPC2378, the RTC can be
clocked by a separate 32.768 kHz oscillator or by a programmable prescale divider based
on the APB clock. Also, the RTC is powered by its own power supply pin, VBAT, which can
be connected to a battery or to the same 3.3 V supply used by the rest of the device.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
28 of 54
LPC2378
NXP Semiconductors
Fast communication chip
The VBAT pin supplies power only to the RTC and the Battery RAM. These two functions
require a minimum of power to operate, which can be supplied by an external battery.
When the CPU and the rest of chip functions are stopped and power removed, the RTC
can supply an alarm output that can be used by external hardware to restore chip power
and resume operation.
7.24.1 Features
• Measures the passage of time to maintain a calendar and clock.
• Ultra low power design to support battery powered systems.
• Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and Day
of Year.
• Dedicated 32 kHz oscillator or programmable prescaler from APB clock.
• Dedicated power supply pin can be connected to a battery or to the main 3.3 V.
• An alarm output pin is included to assist in waking up from Deep power-down mode,
or when the chip has had power removed to all functions except the RTC and Battery
RAM.
• Periodic interrupts can be generated from increments of any field of the time registers,
and selected fractional second values.
• 2 kB data SRAM powered by VBAT.
• RTC and Battery RAM power supply is isolated from the rest of the chip.
7.25 Clocking and power control
7.25.1 Crystal oscillators
The LPC2378 includes three independent oscillators. These are the Main Oscillator, the
Internal RC oscillator, and the RTC oscillator. Each oscillator can be used for more than
one purpose as required in a particular application. Any of the three clock sources can be
chosen by software to drive the PLL and ultimately the CPU.
Following reset, the LPC2378 will operate from the Internal RC oscillator until switched by
software. This allows systems to operate without any external crystal and the bootloader
code to operate at a known frequency.
7.25.1.1
Internal RC oscillator
The IRC may be used as the clock source for the WDT, and/or as the clock that drives the
PLL and subsequently the CPU. The nominal IRC frequency is 4 MHz. The IRC is
trimmed to 1 % accuracy.
Upon power-up or any chip reset, the LPC2378 uses the IRC as the clock source.
Software may later switch to one of the other available clock sources.
7.25.1.2
Main oscillator
The main oscillator can be used as the clock source for the CPU, with or without using the
PLL. The main oscillator operates at frequencies of 1 MHz to 24 MHz. This frequency can
be boosted to a higher frequency, up to the maximum CPU operating frequency, by the
PLL. The clock selected as the PLL input is PLLCLKIN. The ARM processor clock
frequency is referred to as CCLK elsewhere in this document. The frequencies of
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
29 of 54
LPC2378
NXP Semiconductors
Fast communication chip
PLLCLKIN and CCLK are the same value unless the PLL is active and connected. The
clock frequency for each peripheral can be selected individually and is referred to as
PCLK. Refer to Section 7.25.2 for additional information.
7.25.1.3
RTC oscillator
The RTC oscillator can be used as the clock source for the RTC and/or the WDT. Also, the
RTC oscillator can be used to drive the PLL and the CPU.
7.25.2 PLL
The PLL accepts an input clock frequency in the range of 32 kHz to 50 MHz. The input
frequency is multiplied up to a high frequency, then divided down to provide the actual
clock used by the CPU and the USB block.
The PLL input, in the range of 32 kHZ to 50 MHz, may initially be divided down by a value
‘N’, which may be in the range of 1 to 256. This input division provides a wide range of
output frequencies from the same input frequency.
Following the PLL input divider is the PLL multiplier. This can multiply the input divider
output through the use of a Current Controlled Oscillator (CCO) by a value ‘M’, in the
range of 1 through 32768. The resulting frequency must be in the range of 275 MHz to
550 MHz. The multiplier works by dividing the CCO output by the value of M, then using a
phase-frequency detector to compare the divided CCO output to the multiplier input. The
error value is used to adjust the CCO frequency.
The PLL is turned off and bypassed following a chip Reset and by entering Power-down
mode. PLL is enabled by software only. The program must configure and activate the PLL,
wait for the PLL to lock, then connect to the PLL as a clock source.
7.25.3 Wake-up timer
The LPC2378 begins operation at power-up and when awakened from Power-down mode
or Deep power-down mode by using the 4 MHz IRC oscillator as the clock source. This
allows chip operation to resume quickly. If the main oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
When the main oscillator is initially activated, the wake-up timer allows software to ensure
that the main oscillator is fully functional before the processor uses it as a clock source
and starts to execute instructions. This is important at power on, all types of Reset, and
whenever any of the aforementioned functions are turned off for any reason. Since the
oscillator and other functions are turned off during Power-down mode, any wake-up of the
processor from Power-down mode makes use of the wake-up Timer.
The Wake-up Timer monitors the crystal oscillator to check whether it is safe to begin
code execution. When power is applied to the chip, or when some event caused the chip
to exit Power-down mode, some time is required for the oscillator to produce a signal of
sufficient amplitude to drive the clock logic. The amount of time depends on many factors,
including the rate of VDD(3V3) ramp (in the case of power on), the type of crystal and its
electrical characteristics (if a quartz crystal is used), as well as any other external circuitry
(e.g., capacitors), and the characteristics of the oscillator itself under the existing ambient
conditions.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
30 of 54
LPC2378
NXP Semiconductors
Fast communication chip
7.25.4 Power control
The LPC2378 supports a variety of power control features. There are four special modes
of processor power reduction: Idle mode, Sleep mode, Power-down mode, and Deep
power-down mode. The CPU clock rate may also be controlled as needed by changing
clock sources, reconfiguring PLL values, and/or altering the CPU clock divider value. This
allows a trade-off of power versus processing speed based on application requirements.
In addition, Peripheral Power Control allows shutting down the clocks to individual on-chip
peripherals, allowing fine tuning of power consumption by eliminating all dynamic power
use in any peripherals that are not required for the application. Each of the peripherals
has its own clock divider which provides even better power control.
The LPC2378 also implements a separate power domain in order to allow turning off
power to the bulk of the device while maintaining operation of the RTC and a small SRAM,
referred to as the Battery RAM.
7.25.4.1
Idle mode
In Idle mode, execution of instructions is suspended until either a Reset or interrupt
occurs. Peripheral functions continue operation during Idle mode and may generate
interrupts to cause the processor to resume execution. Idle mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
7.25.4.2
Sleep mode
In Sleep mode, the oscillator is shut down and the chip receives no internal clocks. The
processor state and registers, peripheral registers, and internal SRAM values are
preserved throughout Sleep mode and the logic levels of chip pins remain static. The
output of the IRC is disabled but the IRC is not powered down for a fast wake-up later. The
32 kHz RTC oscillator is not stopped because the RTC interrupts may be used as the
wake-up source. The PLL is automatically turned off and disconnected. The CCLK and
USB clock dividers automatically get reset to zero.
The Sleep mode can be terminated and normal operation resumed by either a Reset or
certain specific interrupts that are able to function without clocks. Since all dynamic
operation of the chip is suspended, Sleep mode reduces chip power consumption to a
very low value. The flash memory is left on in Sleep mode, allowing a very quick wake-up.
On the wake-up of sleep mode, if the IRC was used before entering sleep mode, the code
execution and peripherals activities will resume after 4 cycles expire. If the main external
oscillator was used, the code execution will resume when 4096 cycles expire.
The customers need to reconfigure the PLL and clock dividers accordingly.
7.25.4.3
Power-down mode
Power-down mode does everything that Sleep mode does, but also turns off the IRC
oscillator and the flash memory. This saves more power, but requires waiting for
resumption of flash operation before execution of code or data access in the flash memory
can be accomplished.
On the wake-up of power-down mode, if the IRC was used before entering power-down
mode, it will take IRC 60 µs to start-up. After this 4 IRC cycles will expire before the code
execution can then be resumed if the code was running from SRAM. In the meantime, the
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
31 of 54
LPC2378
NXP Semiconductors
Fast communication chip
flash wake-up timer then counts 4 MHz IRC clock cycles to make the 100 µs flash start-up
time. When it times out, access to the flash will be allowed. The customers need to
reconfigure the PLL and clock dividers accordingly.
7.25.4.4
Deep power-down mode
Deep power-down mode is like Power-down mode, but the on-chip regulator that supplies
power to internal logic is also shut off. This produces the lowest possible power
consumption without actually removing power from the entire chip. Since Deep
power-down mode shuts down the on-chip logic power supply, there is no register or
memory retention, and resumption of operation involves the same activities as a full-chip
reset.
If power is supplied to the LPC2378 during Deep power-down mode, wake-up can be
caused by the RTC Alarm or external Reset.
While in Deep power-down mode, external device power may be removed. In this case,
the LPC2378 will start up when external power is restored.
Essential data may be retained through Deep power-down mode (or through complete
powering off of the chip) by storing data in the Battery RAM, as long as the external power
to the VBAT pin is maintained.
7.25.4.5
Power domains
The LPC2378 provides two independent power domains that allow the bulk of the device
to have power removed while maintaining operation of the RTC and the Battery RAM.
On the LPC2378, I/O pads are powered by the 3.3 V (VDD(3V3)) pins, while the
VDD(DCDC)(3V3) and VDD(1V8) pins power the on-chip DC-to-DC converter which in turn
provides power to the CPU and most of the peripherals.
Depending on the LPC2378 application, a design can use two power options to manage
power consumption.
The first option assumes power consumption is not a concern and the design ties the
VDD(3V3) and VDD(DCDC)(3V3) pins together while the VDD(1V8) pins are not connected. This
approach requires only one 3.3 V power supply for both pads, the CPU, and peripherals.
While this solution is simple, it does not support powering down the I/O pad ring “on the
fly” while keeping the CPU and peripherals alive.
The second option uses two power supplies; a 3.3 V supply for the I/O pads (VDD(3V3)) and
a dedicated 1.8 V supply for the CPU (VDD(1V8)). When using this option, the on-chip
DC-to-DC converter remains powered down because the VDD(DCDC)(3V3) pins must not be
connected if the VDD(1V8) pins are attached to the 1.8 V supply. This second supply option
enables shutting down the VDD(3V3) supply to power off the I/O pads “on the fly”, while the
CPU and peripherals stay active thanks to the second independent 1.8 V supply.
The VBAT pin supplies power only to the RTC and the Battery RAM. These two functions
require a minimum of power to operate, which can be supplied by an external battery.
When the CPU and the rest of chip functions are stopped and power removed, the RTC
can supply an alarm output that may be used by external hardware to restore chip power
and resume operation.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
32 of 54
LPC2378
NXP Semiconductors
Fast communication chip
7.26 System control
7.26.1 Reset
Reset has four sources on the LPC2378: the RESET pin, the Watchdog reset, power-on
reset, and the BrownOut Detection (BOD) circuit. The RESET pin is a Schmitt trigger input
pin. Assertion of chip Reset by any source, once the operating voltage attains a usable
level, starts the Wake-up timer (see description in Section 7.25.3 “Wake-up timer”),
causing reset to remain asserted until the external Reset is de-asserted, the oscillator is
running, a fixed number of clocks have passed, and the flash controller has completed its
initialization.
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the Boot Block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values.
7.26.2 Brownout detection
The LPC2378 includes 2-stage monitoring of the voltage on the VDD(3V3) pins. If this
voltage falls below 2.95 V, the BOD asserts an interrupt signal to the Vectored Interrupt
Controller. This signal can be enabled for interrupt in the Interrupt Enable Register in the
VIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading a
dedicated status register.
The second stage of low-voltage detection asserts Reset to inactivate the LPC2378 when
the voltage on the VDD(3V3) pins falls below 2.65 V. This Reset prevents alteration of the
flash as operation of the various elements of the chip would otherwise become unreliable
due to low voltage. The BOD circuit maintains this reset down below 1 V, at which point
the power-on reset circuitry maintains the overall Reset.
Both the 2.95 V and 2.65 V thresholds include some hysteresis. In normal operation, this
hysteresis allows the 2.95 V detection to reliably interrupt, or a regularly-executed event
loop to sense the condition.
7.26.3 Code security
This feature of the LPC2378 allows an application to control whether it can be debugged
or protected from observation.
If after reset the on-chip bootloader detects a valid checksum in flash and reads
0x8765 4321 from address 0x1FC in flash, debugging will be disabled and thus the code
in flash will be protected from observation. Once debugging is disabled, it can be enabled
by performing a full chip erase using the ISP.
7.26.4 AHB bus
The LPC2378 implements two AHB buses in order to allow the Ethernet block to operate
without interference caused by other system activity. The primary AHB, referred to as
AHB1, includes the Vectored Interrupt Controller, GPDMA controller, USB interface, and
8 kB SRAM primarily intended for use by the USB.
The second AHB, referred to as AHB2, includes only the Ethernet block and an
associated 16 kB SRAM. In addition, a bus bridge is provided that allows the secondary
AHB to be a bus master on AHB1, allowing expansion of Ethernet buffer space into
off-chip memory or unused space in memory residing on AHB1.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
33 of 54
LPC2378
NXP Semiconductors
Fast communication chip
In summary, bus masters with access to AHB1 are the ARM7 itself, the USB block, the
GPDMA function, and the Ethernet block (via the bus bridge from AHB2). Bus masters
with access to AHB2 are the ARM7 and the Ethernet block.
7.26.5 External interrupt inputs
The LPC2378 includes up to 50 edge sensitive interrupt inputs combined with up to four
level sensitive external interrupt inputs as selectable pin functions. The external interrupt
inputs can optionally be used to wake up the processor from Power-down mode.
7.26.6 Memory mapping control
The memory mapping control alters the mapping of the interrupt vectors that appear at the
beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the Boot
ROM, the SRAM, or external memory. This allows code running in different memory
spaces to have control of the interrupts.
7.27 Emulation and debugging
The LPC2378 support emulation and debugging via a JTAG serial port. A trace port
allows tracing program execution. Debugging and trace functions are multiplexed only with
GPIOs on P2[0] to P2[9]. This means that all communication, timer, and interface
peripherals residing on other pins are available during the development and debugging
phase as they are when the application is run in the embedded system itself.
7.27.1 EmbeddedICE
The EmbeddedICE logic provides on-chip debug support. The debugging of the target
system requires a host computer running the debugger software and an EmbeddedICE
protocol convertor. The EmbeddedICE protocol convertor converts the Remote Debug
Protocol commands to the JTAG data needed to access the ARM7TDMI-S core present
on the target system.
The ARM core has a Debug Communication Channel (DCC) function built-in. The DCC
allows a program running on the target to communicate with the host debugger or another
separate host without stopping the program flow or even entering the debug state. The
DCC is accessed as a coprocessor 14 by the program running on the ARM7TDMI-S core.
The DCC allows the JTAG port to be used for sending and receiving data without affecting
the normal program flow. The DCC data and control registers are mapped in to addresses
in the EmbeddedICE logic.
7.27.2 Embedded trace
Since the LPC2378 have significant amounts of on-chip memories, it is not possible to
determine how the processor core is operating simply by observing the external pins. The
ETM provides real-time trace capability for deeply embedded processor cores. It outputs
information about processor execution to a trace port. A software debugger allows
configuration of the ETM using a JTAG interface and displays the trace information that
has been captured.
The ETM is connected directly to the ARM core and not to the main AMBA system bus. It
compresses the trace information and exports it through a narrow trace port. An external
Trace Port Analyzer captures the trace information under software debugger control. The
trace port can broadcast the Instruction trace information. Instruction trace (or PC trace)
shows the flow of execution of the processor and provides a list of all the instructions that
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
34 of 54
LPC2378
NXP Semiconductors
Fast communication chip
were executed. Instruction trace is significantly compressed by only broadcasting branch
addresses as well as a set of status signals that indicate the pipeline status on a cycle by
cycle basis. Trace information generation can be controlled by selecting the trigger
resource. Trigger resources include address comparators, counters and sequencers.
Since trace information is compressed the software debugger requires a static image of
the code being executed. Self-modifying code can not be traced because of this
restriction.
7.27.3 RealMonitor
RealMonitor is a configurable software module, developed by ARM Inc., which enables
real-time debug. It is a lightweight debug monitor that runs in the background while users
debug their foreground application. It communicates with the host using the DCC, which is
present in the EmbeddedICE logic. The LPC2378 contain a specific configuration of
RealMonitor software programmed into the on-chip ROM memory.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
35 of 54
LPC2378
NXP Semiconductors
Fast communication chip
8. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
Min
Max
Unit
VDD(1V8)
supply voltage (1.8 V)
internal rail
1.65
1.95
V
VDD(3V3)
supply voltage (3.3 V)
core and external
rail
3.0
3.6
V
3.0
3.6
V
−0.5
+4.6
V
−0.5
+4.6
V
−0.5
+4.6
V
−0.5
+5.1
V
[2]
−0.5
+6.0
V
other I/O pins
[2][3]
−0.5
VDD(3V3) +
0.5
V
VDD(DCDC)(3V3) DC-to-DC converter supply voltage
(3.3 V)
VDDA
analog 3.3 V pad supply voltage
Vi(VBAT)
input voltage on pin VBAT
Vi(VREF)
input voltage on pin VREF
VIA
analog input voltage
on ADC related
pins
VI
input voltage
5 V tolerant I/O
pins; only valid
when the VDD(3V3)
supply voltage is
present
for the RTC
IDD
supply current
per supply pin
[4]
-
100
mA
ISS
ground current
per ground pin
[4]
-
100
mA
[5]
−40
+125
°C
-
1.5
W
−2000
+2000
V
Tstg
storage temperature
Ptot(pack)
total power dissipation (per package)
based on package
heat transfer, not
device power
consumption
Vesd
electrostatic discharge voltage
human body
model; all pins
[6]
[1]
The following applies to the Limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Including voltage on outputs in 3-state mode.
[3]
Not to exceed 4.6 V.
[4]
The peak current is limited to 25 times the corresponding maximum current.
[5]
Dependent on package type.
[6]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
36 of 54
LPC2378
NXP Semiconductors
Fast communication chip
9. Static characteristics
Table 5.
Static characteristics
Tamb = −40 °C to +85 °C for commercial applications, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
VDD(1V8)
supply voltage (1.8 V)
internal rail
1.65
1.8
1.95
V
VDD(3V3)
supply voltage (3.3 V)
core and external rail
3.0
3.3
3.6
V
VDD(DCDC)(3V3)
DC-to-DC converter
supply voltage (3.3 V)
3.0
3.3
3.6
V
VDDA
analog 3.3 V pad
supply voltage
3.0
3.3
3.6
V
Vi(VBAT)
input voltage on pin
VBAT
2.0
3.3
3.6
V
Vi(VREF)
input voltage on pin
VREF
2.5
3.3
VDDA
V
[2]
Standard port pins, RESET, RTCK
IIL
LOW-level input
current
VI = 0 V; no pull-up
-
-
3
µA
IIH
HIGH-level input
current
VI = VDD(3V3); no pull-down
-
-
3
µA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD(3V3);
no pull-up/down
-
-
3
µA
Ilatch
I/O latch-up current
−(0.5VDD(3V3)) < VI <
(1.5VDD(3V3));
-
-
100
mA
0
-
5.5
V
0
-
VDD(3V3)
V
Tj < 125 °C
[3][4][5]
VI
input voltage
pin configured to provide a
digital function
VO
output voltage
output active
VIH
HIGH-level input
voltage
2.0
-
-
V
VIL
LOW-level input
voltage
-
-
0.8
V
Vhys
hysteresis voltage
-
0.4
-
V
VDD(3V3) −
0.4
-
-
V
VOH
HIGH-level output
voltage
IOH = −4 mA
[6]
VOL
LOW-level output
voltage
IOL = −4 mA
[6]
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD(3V3) − 0.4 V
[6]
−4
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
[6]
4
-
-
mA
IOHS
HIGH-level
short-circuit output
current
VOH = 0 V
[7]
-
-
−45
mA
IOLS
LOW-level short-circuit VOL = VDDA
output current
[7]
-
-
50
mA
Ipd
pull-down current
[8]
10
50
150
µA
VI = 5 V
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
37 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 5.
Static characteristics …continued
Tamb = −40 °C to +85 °C for commercial applications, unless otherwise specified.
Min
Typ[1]
Max
Unit
−15
−50
−85
µA
0
0
0
µA
CCLK = 10 MHz
-
15
-
mA
CCLK = 72 MHz
-
63
-
mA
CCLK = 10 MHz
-
21
-
mA
CCLK = 72 MHz
-
92
-
mA
CCLK = 10 MHz
-
27
-
mA
CCLK = 72 MHz
-
125
-
mA
-
150
-
µA
Symbol
Parameter
Conditions
Ipu
pull-up current
VI = 0 V
[8]
VDD(3V3) < VI < 5 V
IDD(DCDC)act(3V3) active mode DC-to-DC VDD(DCDC)(3V3) = 3.3 V;
converter supply
Tamb = 25 °C; code
current (3.3 V)
while(1){}
executed from flash; no
peripherals enabled;
PCLK = CCLK
all peripherals enabled;
PCLK = CCLK / 8
all peripherals enabled;
PCLK = CCLK
IDD(DCDC)pd(3V3)
power-down mode
DC-to-DC converter
supply current (3.3 V)
IDD(DCDC)dpd(3V3) deep power-down
mode DC-to-DC
converter supply
current (3.3 V)
IBATact
I2C-bus
active mode battery
supply current
VDD(DCDC)(3V3) = 3.3 V;
Tamb = 25 °C
VDD(DCDC)(3V3) = 3.3 V;
Tamb = 25 °C
-
15
-
µA
DC-to-DC converter on
[9]
-
20
-
µA
DC-to-DC converter off
[9]
-
28
-
µA
V
pins (P0[27] and P0[28])
VIH
HIGH-level input
voltage
0.7VDD(3V3) -
-
VIL
LOW-level input
voltage
-
-
0.3VDD(3V3) V
Vhys
hysteresis voltage
VOL
LOW-level output
voltage
IOLS = 3 mA
[6]
ILI
input leakage current
VI = VDD(3V3)
[10]
VI = 5 V
-
0.5VDD(3V3) -
V
-
-
0.4
V
-
2
4
µA
-
10
22
µA
Oscillator pins
Vi(XTAL1)
input voltage on pin
XTAL1
0
-
1.8
V
Vo(XTAL2)
output voltage on pin
XTAL2
0
-
1.8
V
Vi(RTCX1)
input voltage on pin
RTCX1
0
-
1.8
V
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
38 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 5.
Static characteristics …continued
Tamb = −40 °C to +85 °C for commercial applications, unless otherwise specified.
Symbol
Parameter
Vo(RTCX2)
output voltage on pin
RTCX2
Conditions
Min
Typ[1]
Max
Unit
0
-
1.8
V
-
-
±10
µA
-
-
5.25
V
USB pins
IOZ
OFF-state output
current
0 V < VI < 3.3 V
VBUS
bus supply voltage
VDI
differential input
sensitivity
|(D+) − (D−)|
0.2
-
-
V
VCM
differential common
mode voltage range
includes VDI range
0.8
-
2.5
V
Vth(rs)se
single-ended receiver
switching threshold
voltage
0.8
-
2.0
V
VOL
LOW-level output
voltage for
low-/full-speed
RL of 1.5 kΩ to 3.6 V
-
-
0.18
V
VOH
HIGH-level output
voltage (driven) for
low-/full-speed
RL of 15 kΩ to GND
2.8
-
3.5
V
Ctrans
transceiver
capacitance
pin to GND
-
-
20
pF
ZDRV
driver output
impedance for driver
which is not
high-speed capable
with 33 Ω series resistor;
steady state drive
36
-
44.1
Ω
Rpu
pull-up resistance
SoftConnect = ON
1.1
-
1.9
kΩ
[11]
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 °C), nominal supply voltages
[2]
The RTC typically fails when Vi(VBAT) drops below 1.6 V.
[3]
Including voltage on outputs in 3-state mode.
[4]
VDD(3V3) supply voltages must be present.
[5]
3-state outputs go into 3-state mode when VDD(3V3) is grounded.
[6]
Accounts for 100 mV voltage drop in all supply lines.
[7]
Only allowed for a short time period.
[8]
Minimum condition for VI = 4.5 V, maximum condition for VI = 5.5 V.
[9]
On pin VBAT.
[10] To VSS.
[11] Includes external resistors of 18 Ω ± 1 % on D+ and D−.
Table 6.
ADC static characteristics
VDDA = 2.5 V to 3.6 V; Tamb = −40 °C to +85 °C unless otherwise specified; ADC frequency 4.5 MHz.
Symbol
Parameter
VIA
analog input voltage
Cia
analog input capacitance
ED
differential linearity error
Conditions
[1][2][3]
LPC2378_1
Preliminary data sheet
Min
Typ
Max
Unit
0
-
VDDA
V
-
-
1
pF
-
-
±1
LSB
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
39 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 6.
ADC static characteristics …continued
VDDA = 2.5 V to 3.6 V; Tamb = −40 °C to +85 °C unless otherwise specified; ADC frequency 4.5 MHz.
Symbol
Min
Typ
Max
Unit
integral non-linearity
[1][4]
-
-
±2
LSB
offset error
[1][5]
-
-
±3
LSB
EG
gain error
[1][6]
-
-
±0.5
%
ET
absolute error
[1][7]
-
-
±4
LSB
[8]
-
-
40
kΩ
EL(adj)
EO
Parameter
Conditions
voltage source interface
resistance
Rvsi
[1]
Conditions: VSSA = 0 V, VDDA = 3.3 V.
[2]
The ADC is monotonic, there are no missing codes.
[3]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 4.
[4]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 4.
[5]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 4.
[6]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 4.
[7]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated ADC
and the ideal transfer curve. See Figure 4.
[8]
See Figure 5.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
40 of 54
LPC2378
NXP Semiconductors
Fast communication chip
offset
error
EO
gain
error
EG
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
offset error
EO
6
7
1018
1019
1020
1021
1022
1023
1024
Via (LSBideal)
1 LSB =
VDDA − VSSA
1024
002aab136
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 4. ADC characteristics
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
41 of 54
LPC2378
NXP Semiconductors
Fast communication chip
LPC2378
20 kΩ
AD0[y]
AD0[y]SAMPLE
3 pF
Rvsi
5 pF
VEXT
VSS
002aac610
Fig 5. Suggested ADC interface - LPC2378 AD0[y] pin
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
42 of 54
LPC2378
NXP Semiconductors
Fast communication chip
10. Dynamic characteristics
Table 7.
Dynamic characteristics of USB pins (full-speed)
CL = 50 pF; Rpu = 1.5 kΩ on D+ to VDD(3V3),unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
10 % to 90 %
8.5
-
13.8
ns
tf
fall time
10 % to 90 %
7.7
-
13.7
ns
tFRFM
differential rise and fall time
matching
tr / tf
-
-
109
%
VCRS
output signal crossover voltage
1.3
-
2.0
V
tFEOPT
source SE0 interval of EOP
see Figure 9
160
-
175
ns
tFDEOP
source jitter for differential transition
to SE0 transition
see Figure 9
−2
-
+5
ns
tJR1
receiver jitter to next transition
−18.5
-
+18.5
ns
tJR2
receiver jitter for paired transitions
10 % to 90 %
−9
-
+9
ns
tEOPR1
EOP width at receiver
must reject as
EOP; see
Figure 9
[1]
40
-
-
ns
tEOPR2
EOP width at receiver
must accept as
EOP; see
Figure 9
[1]
82
-
-
ns
Min
Typ[2]
Max
Unit
[1]
Characterized but not implemented as production test. Guaranteed by design.
Table 8.
Dynamic characteristics
Tamb = −40 °C to +85 °C for commercial applications; VDD(3V3) over specified ranges.[1]
Symbol
Parameter
Conditions
External clock
fosc
oscillator frequency
10
-
25
MHz
Tcy(clk)
clock cycle time
40
-
100
ns
tCHCX
clock HIGH time
Tcy(clk) × 0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk) × 0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
20 + 0.1 × Cb[3]
-
-
ns
I2C-bus
pins (P0[27] and P0[28])
output fall time
tf(o)
VIH to VIL
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 °C), nominal supply voltages.
[3]
Bus capacitance Cb in pF, from 10 pF to 400 pF.
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
43 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 9.
External memory interface dynamic characteristics
CL = 25 pF, Tamb = 40 °C.
Symbol
Parameter
Conditions
Min
Typ Max
Unit
Common to read and write cycles
tCHAV
XCLK HIGH to address valid
time
-
-
10
ns
tCHCSL
XCLK HIGH to CS LOW time
-
-
10
ns
tCHCSH
XCLK HIGH to CS HIGH
time
-
-
10
ns
tCHANV
XCLK HIGH to address
invalid time
-
-
10
ns
Read cycle parameters
tCSLAV
CS LOW to address valid
time
[1]
−5
-
+10
ns
tOELAV
OE LOW to address valid
time
[1]
−5
-
+10
ns
tCSLOEL
CS LOW to OE LOW time
−5
-
+5
ns
(Tcy(CCLK) × (2 + WST1)) +
(−20)
-
-
ns
tam
memory access time
[2][3]
tam(ibr)
memory access time (initial
burst-ROM)
[2][3]
(Tcy(CCLK) × (2 + WST1)) +
(−20)
-
-
ns
tam(sbr)
memory access time
(subsequent burst-ROM)
[2][4]
Tcy(CCLK) + (−20)
-
-
ns
th(D)
data hold time
0
-
-
ns
tCSHOEH
CS HIGH to OE HIGH time
−5
-
+5
ns
tOEHANV
OE HIGH to address invalid
time
−5
-
+5
ns
tCHOEL
XCLK HIGH to OE LOW time
−5
-
+5
ns
tCHOEH
XCLK HIGH to OE HIGH
time
−5
-
+5
ns
Tcy(CCLK) − 10
-
-
ns
[5]
Write cycle parameters
[1]
tAVCSL
address valid to CS LOW
time
tCSLDV
CS LOW to data valid time
−5
-
+5
ns
tCSLWEL
CS LOW to WE LOW time
−5
-
+5
ns
tCSLBLSL
CS LOW to BLS LOW time
−5
-
+5
ns
tWELDV
WE LOW to data valid time
−5
-
+5
ns
tCSLDV
CS LOW to data valid time
−5
-
+5
ns
Tcy(CCLK) × (1 + WST2) − 5
-
Tcy(CCLK) × (1 +
WST2) + 5
ns
tWELWEH
WE LOW to WE HIGH time
[2]
tBLSLBLSH
BLS LOW to BLS HIGH time
[2]
Tcy(CCLK) × (1 + WST2) − 5
-
Tcy(CCLK) ×
(1 + WST2) + 5
ns
tWEHANV
WE HIGH to address invalid
time
[2]
Tcy(CCLK) − 5
-
Tcy(CCLK) + 5
ns
tWEHDNV
WE HIGH to data invalid time
[2]
(2 × Tcy(CCLK)) − 5
-
(2 × Tcy(CCLK)) + 5 ns
BLS HIGH to address invalid
time
[2]
Tcy(CCLK) − 5
-
Tcy(CCLK) + 5
tBLSHANV
LPC2378_1
Preliminary data sheet
ns
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
44 of 54
LPC2378
NXP Semiconductors
Fast communication chip
Table 9.
External memory interface dynamic characteristics …continued
CL = 25 pF, Tamb = 40 °C.
Symbol
Parameter
Conditions
[2]
Min
Typ Max
Unit
(2 × Tcy(CCLK)) − 5
-
(2 × Tcy(CCLK)) + 5 ns
tBLSHDNV
BLS HIGH to data invalid
time
tCHDV
XCLK HIGH to data valid
time
-
-
10
ns
tCHWEL
XCLK HIGH to WE LOW
time
-
-
10
ns
tCHBLSL
XCLK HIGH to BLS LOW
time
-
-
10
ns
tCHWEH
XCLK HIGH to WE HIGH
time
-
-
10
ns
tCHBLSH
XCLK HIGH to BLS HIGH
time
-
-
10
ns
tCHDNV
XCLK HIGH to data invalid
time
-
-
10
ns
[1]
Except on initial access, in which case the address is set up Tcy(CCLK) earlier.
[2]
Tcy(CCLK) = 1⁄CCLK.
[3]
Latest of address valid, CS LOW, OE LOW to data valid.
[4]
Address valid to data valid.
[5]
Earliest of CS HIGH, OE HIGH, address change to data invalid.
Table 10.
Standard read access specifications
Access cycle
Max frequency
WST setting
Memory access time requirement
WST ≥ 0; round up to
integer
standard read
2 + WST 1
f MAX ≤ -------------------------------t RAM + 20 ns
t RAM + 20 ns
WST 1 ≥ -------------------------------- – 2
t cy ( CCLK )
t RAM ≤ t cy ( CCLK ) × ( 2 + WST 1 ) – 20 ns
standard write
1 + WST 2
f MAX ≤ ---------------------------------t WRITE + 5 ns
t WRITE – t CYC + 5
WST 2 ≥ -------------------------------------------t cy ( CCLK )
t WRITE ≤ t cy ( CCLK ) × ( 1 + WST 2 ) – 5 ns
burst read - initial
2 + WST 1
f MAX ≤ -------------------------------t INIT + 20 ns
t INIT + 20 ns
WST 1 ≥ -------------------------------- – 2
t cy ( CCLK )
t INIT ≤ t cy ( CCLK ) × ( 2 + WST 1 ) – 20 ns
burst read - subsequent 3 ×
1
f MAX ≤ --------------------------------t ROM + 20 ns
N/A
t ROM ≤ t cy ( CCLK ) – 20 ns
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
45 of 54
LPC2378
NXP Semiconductors
Fast communication chip
10.1 Timing
XCLK
tCSLAV
tCSHOEH
CS
addr
tam
th(D)
data
tCSLOEL
tOELAV
tOEHANV
OE
tCHOEL
tCHOEH
002aaa749
Fig 6. External memory read access
XCLK
tCSLDV
CS
tAVCSL
tCSLWEL
tWELWEH
tBLSLBLSH
BLS/WE
tWEHANV
tCSLBLSL
tWELDV
tBLSHANV
addr
tCSLDV
tWEHDNV
tBLSHDNV
data
OE
002aaa750
Fig 7. External memory write access
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
46 of 54
LPC2378
NXP Semiconductors
Fast communication chip
VDD − 0.5 V
0.45 V
0.2VDD + 0.9 V
0.2VDD − 0.1 V
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 8. External clock timing
tPERIOD
crossover point
extended
crossover point
differential
data lines
source EOP width: tFEOPT
differential data to
SEO/EOP skew
n · tPERIOD + tFDEOP
receiver EOP width: tEOPR1, tEOPR2
002aab561
Fig 9. Differential data-to-EOP transition skew and EOP width
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
47 of 54
LPC2378
NXP Semiconductors
Fast communication chip
11. Application information
11.1 Suggested USB interface solutions
VDD(3V3)
USB_UP_LED
USB_CONNECT
LPC23XX
soft-connect switch
R1
1.5 kW
VBUS
USB_D+ RS = 33 W
USB_D-
USB-B
connector
RS = 33 W
VSS
002aac578
Fig 10. LPC2378 USB interface on a self-powered device
VDD(3V3)
R2
LPC23XX
USB_UP_LED
R1
1.5 kW
VBUS
USB-B
connector
USB_D+ RS = 33 W
USB_D− RS = 33 W
VSS
002aac579
Fig 11. LPC2378 USB interface on a bus-powered device
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
48 of 54
LPC2378
NXP Semiconductors
Fast communication chip
12. Package outline
LQFP144: plastic low profile quad flat package; 144 leads; body 20 x 20 x 1.4 mm
SOT486-1
c
y
X
A
73
72
108
109
ZE
e
E HE
A A2
(A 3)
A1
θ
wM
Lp
bp
L
pin 1 index
detail X
37
144
1
36
v M A
ZD
wM
bp
e
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.15
0.05
1.45
1.35
0.25
0.27
0.17
0.20
0.09
20.1
19.9
20.1
19.9
0.5
HD
HE
22.15 22.15
21.85 21.85
L
Lp
v
w
y
1
0.75
0.45
0.2
0.08
0.08
Z D(1) Z E(1)
1.4
1.1
1.4
1.1
θ
o
7
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT486-1
136E23
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-03-14
03-02-20
Fig 12. Package outline SOT486-1 (LQFP144)
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
49 of 54
LPC2378
NXP Semiconductors
Fast communication chip
13. Abbreviations
Table 11.
Acronym list
Acronym
Description
ADC
Analog-to-Digital Converter
AHB
Advanced High-performance Bus
AMBA
Advanced Microcontroller Bus Architecture
APB
Advanced Peripheral Bus
BLS
Byte Lane Select
BOD
BrownOut Detection
CAN
Controller Area Network
CTS
Clear To Send
DAC
Digital-to-Analog Converter
DCC
Debug Communication Channel
DMA
Direct Memory Access
DSP
Digital Signal Processing
EOP
End Of Packet
ETM
Embedded Trace Macrocell
GPIO
General Purpose Input/Output
JTAG
Joint Test Action Group
MII
Media Independent Interface
PHY
Physical Layer
PLL
Phase-Locked Loop
PWM
Pulse Width Modulator
RMII
Reduced Media Independent Interface
RTS
Request To Send
SE0
Single Ended Zero
SPI
Serial Peripheral Interface
SSI
Synchronous Serial Interface
SSP
Synchronous Serial Port
TTL
Transistor-Transistor Logic
UART
Universal Asynchronous Receiver/Transmitter
USB
Universal Serial Bus
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
50 of 54
LPC2378
NXP Semiconductors
Fast communication chip
14. Revision history
Table 12.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
LPC2378_1
20061206
Preliminary data sheet
-
-
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
51 of 54
LPC2378
NXP Semiconductors
Fast communication chip
15. Legal information
15.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
15.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
NXP Semiconductors accepts no liability for inclusion and/or use of NXP
Semiconductors products in such equipment or applications and therefore
such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
15.4 Trademarks
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a NXP Semiconductors product can reasonably be expected to
result in personal injury, death or severe property or environmental damage.
SoftConnect — is a trademark of NXP B.V.
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
GoodLink — is a trademark of NXP B.V.
16. Contact information
For additional information, please visit: http://www.nxp.com
For sales office addresses, send an email to: [email protected]
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
52 of 54
LPC2378
NXP Semiconductors
Fast communication chip
17. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
4.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
7
Functional description . . . . . . . . . . . . . . . . . . 15
7.1
Architectural overview. . . . . . . . . . . . . . . . . . . 15
7.2
On-chip flash programming memory . . . . . . . 16
7.3
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 16
7.4
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.5
Interrupt controller . . . . . . . . . . . . . . . . . . . . . 17
7.5.1
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 18
7.6
Pin connect block . . . . . . . . . . . . . . . . . . . . . . 18
7.7
External memory controller. . . . . . . . . . . . . . . 18
7.7.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.8
General purpose DMA controller . . . . . . . . . . 19
7.8.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.9
Fast general purpose parallel I/O . . . . . . . . . . 20
7.9.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.10
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.10.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.11
USB interface . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.11.1
USB device controller . . . . . . . . . . . . . . . . . . . 22
7.11.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.12
CAN controller and acceptance filters . . . . . . 22
7.12.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.13
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.13.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.14
10-bit DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.14.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.15
UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.15.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.16
SPI serial I/O controller. . . . . . . . . . . . . . . . . . 24
7.16.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.17
SSP serial I/O controller . . . . . . . . . . . . . . . . . 24
7.17.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.18
SD/MMC card interface . . . . . . . . . . . . . . . . . 25
7.18.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.19
I2C-bus serial I/O controllers. . . . . . . . . . . . . . 25
7.19.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.20
I2S-bus serial I/O controllers . . . . . . . . . . . . . . 26
7.20.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.21
General purpose 32-bit timers/external event
counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.21.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.22
Pulse width modulator . . . . . . . . . . . . . . . . . .
7.22.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.23
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . .
7.23.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.24
RTC and battery RAM . . . . . . . . . . . . . . . . . .
7.24.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.25
Clocking and power control . . . . . . . . . . . . . .
7.25.1
Crystal oscillators . . . . . . . . . . . . . . . . . . . . . .
7.25.1.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . .
7.25.1.2 Main oscillator . . . . . . . . . . . . . . . . . . . . . . . .
7.25.1.3 RTC oscillator. . . . . . . . . . . . . . . . . . . . . . . . .
7.25.2
PLL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.25.3
Wake-up timer . . . . . . . . . . . . . . . . . . . . . . . .
7.25.4
Power control . . . . . . . . . . . . . . . . . . . . . . . . .
7.25.4.1 Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.25.4.2 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . .
7.25.4.3 Power-down mode . . . . . . . . . . . . . . . . . . . . .
7.25.4.4 Deep power-down mode . . . . . . . . . . . . . . . .
7.25.4.5 Power domains. . . . . . . . . . . . . . . . . . . . . . . .
7.26
System control . . . . . . . . . . . . . . . . . . . . . . . .
7.26.1
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.26.2
Brownout detection . . . . . . . . . . . . . . . . . . . .
7.26.3
Code security . . . . . . . . . . . . . . . . . . . . . . . .
7.26.4
AHB bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.26.5
External interrupt inputs . . . . . . . . . . . . . . . . .
7.26.6
Memory mapping control . . . . . . . . . . . . . . . .
7.27
Emulation and debugging. . . . . . . . . . . . . . . .
7.27.1
EmbeddedICE . . . . . . . . . . . . . . . . . . . . . . . .
7.27.2
Embedded trace. . . . . . . . . . . . . . . . . . . . . . .
7.27.3
RealMonitor . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
9
Static characteristics . . . . . . . . . . . . . . . . . . .
10
Dynamic characteristics . . . . . . . . . . . . . . . . .
10.1
Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
Application information . . . . . . . . . . . . . . . . .
11.1
Suggested USB interface solutions . . . . . . . .
12
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
13
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . .
14
Revision history . . . . . . . . . . . . . . . . . . . . . . .
15
Legal information . . . . . . . . . . . . . . . . . . . . . .
15.1
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
15.2
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
27
27
28
28
28
29
29
29
29
29
30
30
30
31
31
31
31
32
32
33
33
33
33
33
34
34
34
34
34
35
36
37
43
46
48
48
49
50
51
52
52
52
52
continued >>
LPC2378_1
Preliminary data sheet
© NXP B.V. 2006. All rights reserved.
Rev. 01 — 6 December 2006
53 of 54
LPC2378
NXP Semiconductors
Fast communication chip
15.4
16
17
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Contact information. . . . . . . . . . . . . . . . . . . . . 52
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2006.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 6 December 2006
Document identifier: LPC2378_1