Datasheet MLX75303 old 488 DownloadLink 5368

MLX75303
Optical Switch SensorEyeC
Features
High precision light switching level
Low temperature dependency
Supply voltage range 3V to 5.5V
TTL and CMOS compatible
Operating temperature -40 up to 125degC
Target 0 ppm defects;
guarantee <10 ppm defects
Solder reflow 260degC, MSL3
Automotive qualification AEC-Q100
RoHS compliant lead-free
Applications
General
• Contactless Switch
• Contactless Position Switch
• Hand presence detection, e.g. for water taps
• Range detection, e.g. staircase detection for robot vacuum cleaners
• Twilight Sensor, e.g. for sun screens, roof windows
• Security Screens
Automotive
• Steering angle measurement
• Contactless switch for steering stocks
• Headlights ON/OFF sensor
• Keyless car entry – hand presence detection
Printers/Copiers
• Paper feed detection
• Paper size and orientation detection
• Toner cartridge presence detection
Versions
Part No.
MLX75303
MLX75303
MLX75303
MLX75303
390107530301
Rev. 001
Temperature
Code
Package Code
E
XD
-40°C to 85°C
SO8 Open Cavity
E
XE
-40°C to 85°C
DFN3x3 Open Cavity
K
XD
-40°C to 125°C
SO8 Open Cavity
K
XE
-40°C to 125°C
DFN3x3 Open Cavity
Page 1 of 13
Option Code
Delivery Form
Tape On Reel
Tape On Reel
Tape On Reel
Tape On Reel
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
1 Functional Diagram
Vdd
VDD
OUT
Ee
Vref
Vss
2 General Description
The Melexis SensorEyeC series are CMOS integrated optical sensor ICs including photodiode,
transimpedance amplifier and output transistor on one chip.
The MLX75303 features a Schmitt Trigger output and is designed for automotive and non-automotive
applications.
The MLX75303 block diagram is shown in Section 1 and contains following blocks: a transimpedance
amplifier to convert and amplify the photocurrent of the photodiode, a voltage reference, a Schmitt trigger and
an open drain output stage.
390107530301
Rev. 001
Page 2 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
Table of Contents
1
Functional Diagram....................................................................................................2
2
General Description ...................................................................................................2
3
DFN3x3 Pin Definitions and Descriptions................................................................4
4
SO8 Pin Definitions and Descriptions......................................................................4
5
Absolute Maximum Ratings ......................................................................................4
6
MLX75303 Specifications ..........................................................................................5
7
Timing diagrams ........................................................................................................7
8
Test diagrams.............................................................................................................8
9
Applications Information ...........................................................................................9
10
DFN3x3 Open Cavity Package Information............................................................10
11
SO8 Open Cavity Package Information..................................................................11
12
Standard information regarding manufacturability of Melexis products with
different soldering processes .................................................................................12
13
ESD Precautions ......................................................................................................12
14
Disclaimer .................................................................................................................13
390107530301
Rev. 001
Page 3 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
3 DFN3x3 Pin Definitions and Descriptions
Pin
Number
1
Pin Name
Description
Type
N.C.
Not connected
Floating
2
Vss
Ground connection
Ground
3
OUT
Active low (= light on) output
Open drain output
4
Vdd
Power supply
Supply
5
N.C.
Not connected
Floating
6..10
N.C.
Not connected
Floating
4 SO8 Pin Definitions and Descriptions
Pin
Number
1
Pin Name
Description
Type
Vss
Ground connection
Ground
2
OUT
Active low (= light on) output
Open drain output
3
Vdd
Power supply
Supply
4
N.C.
Not connected
Floating
5..8
N.C.
Not connected
Floating
5 Absolute Maximum Ratings
Valid for all MLX75303 versions. All voltages are referenced to Vss.
Symbol
Rating
Vdd
Supply Voltage, VDD (over voltage)
Vout
DC Output Voltage
Iout
DC Output Current, per Pin
TStg
Storage Temperature Range, TS
VESD-HBM
ESD Sensitivity (Human Body Model
according to CDF-AEC-Q100)
VESD-MM
ESD Sensitivity (Machine Model according to CDF-AEC-Q100)
Value
Unit
-0.3 to 7
V
-0.3 to Vdd+0.3V
V
±20
mA
-40 to 125
°C
4
kV
200
V
For proper operation Vout should be constrained to the range Vss≤Vout≤Vdd.
Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximumrated conditions for extended periods may affect device reliability.
390107530301
Rev. 001
Page 4 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
6 MLX75303 Specifications
All voltages are referenced to Vss.
Symbol
Vdd
Parameter
Conditions
Supply Voltage
Idd
Static Power Supply Current
Eeon
Irradiance for Threshold “on”
Vdd=5V, λ=850nm,
Tamb=25˚C
Eeoff/Eeon
Hysteresis
Vdd=5V, λ=850nm,
Tamb=-40 .. 85˚C
Tamb=85 ..125˚C
TC
Temperature Coefficient of threshold “on”
Vdd=5V, λ=850nm
Maximum Irradiance
Typ
3
At Vdd=5.5V,
unloaded output
Eemax
Min
Vdd=5V, λ=850nm,
Tamb=25˚C
Tamb=25˚C
Vdd=5.5V, Ee>Eon,
IOL=16mA
Vdd=5.5V, Ee=0
Vdd=5.5V, Ee=0
68
60
60
Units
Test
5.5
V
V
2.5
mA
V
102
µW/cm
80
90
%
%
V
V
%/K
X
µW/cm2
V
2
X
-0.44
15x
Eeon_max
1000x
Eeon_max
µW/cm
2
1000
nm
X
0
0.4
V
V
0
Vdd+0.3
1
V
µA
X
V
0
24
µs
V
mm2
D
300
20
20
ns
µs
µs
µs
µs
X
V
V
V
X
85
125
°C
°C
V
V
Spectral Bandwidth
VOL
Output voltage low
VOH
IOH
Output voltage high
High level output current
tsetup
Electrical setup-time
Spd
Area of photodiode
tf
ton
toff
tp
tG
Fall time
Turn-on time
Turn-off time
Light pulse duration
Light pulse rejection
(a), Ee=Eeon_max
(a), Ee=Eeon_max
(a), Ee=30x Eeon_max
(a)
(a)
0
0
0
20
TA
Operating Temperature Range
Temperature Code E
Temperature Code K
-40
-40
0.36
10
10
2
(a) Vdd=5V, RL=1kOhm, CL=2nF, λ= 850nm
1
The column Test indicates if the specific parameter is tested in production. Following symbols are used:
V: the specific parameter is tested in production
X: the specific parameter is verified in characterisation, but is not tested in production (e.g. timings and capacitances)
D: the specific parameter is guaranteed by design and is not tested as such in production
390107530301
Rev. 001
Page 5 of 13
V
500
λ0.3
RL=1kOhm, CL=2nF,
λ= 850nm
85
Max
Data Sheet
Mar/08
1
MLX75303
Optical Switch SensorEyeC
Typical ton and toff values for light intensities up to 1000x Eon (at 25degC)
MLX75303 t_On @ 5V
MLX75303 t_Off @ 5V
20
15
t_Off (µs)
t_On (µs)
20
10
5
15
10
5
0
0
1
10
100
Light Intensity (x Eon)
1
1000
10
100
1000
Light Intensity (x Eon)
Typical Eon/Eoff (Hysteresis) value over temperature
E_on/E_off (Hysteresis) @ 5V
Hysteresis (%)
100
80
60
40
20
0
-40
-20
0
20
40
60
80
100
120
140
Temperature (degC)
390107530301
Rev. 001
Page 6 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
Spectral Responsivity Curve
Typical Photodiode Spectral Response Curve (%), without Anti
Reflection Coating*
*There is also an option for an Anti Reflection Coating. This will remove the interference
ripples in the figure above. With this special Anti Reflection Coating, the sensitivity curve in
function of wavelength will be somewhat lower (typically 4%) but will no longer display
interference ripples.
7 Timing diagrams
Definition of the switch-on and switch-off thresholds
390107530301
Rev. 001
Definition of the switch-on and switch-off delays
Page 7 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
Definition of the light pulse duration
Definition of the power-on delay
8 Test diagrams
Measurement and trimming of Eeon, Eeoff and hysteresis:
390107530301
Rev. 001
Page 8 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
Functional check of Eeon and Eeoff thresholds and timing measurements (Go-NoGo tests):
9 Applications Information
A typical connection diagram is shown in the figure below. A load resistor RL is needed to get a voltage level
out. The load capacitance CL is typically formed by the input capacitance of the component that is connected
to the sensor output, the wiring capacitance and the output capacitance of the sensor itself.
Vdd
Ee
RL
OUT
MLX75303
CL
Decoupling capacitors between Vdd and Vss (1uF in parallel with 100nF) are highly recommended in all configurations.
Recommendation: every change in the application should be agreed by both parties.
390107530301
Rev. 001
Page 9 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
10 DFN3x3 Open Cavity Package Information
DFN3x3 open cavity package, MSL3, 260˚C soldering profile (target). Lead free component.
390107530301
Rev. 001
Page 10 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
11 SO8 Open Cavity Package Information
SO8 open cavity package, MSL3, 260˚C soldering profile (target). Lead free component.
390107530301
Rev. 001
Page 11 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
12 Standard information regarding manufacturability of Melexis
products with different soldering processes
Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity
level according to following test methods:
Reflow Soldering SMD’s (Surface Mount Devices)
•
•
IPC/JEDEC J-STD-020
Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices
(classification reflow profiles according to table 5-2)
EIA/JEDEC JESD22-A113
Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing
(reflow profiles according to table 2)
Wave Soldering SMD’s (Surface Mount Devices)
•
EN60749-20
Resistance of plastic- encapsulated SMD’s to combined effect of moisture and soldering heat
Solderability SMD’s (Surface Mount Devices)
•
EIA/JEDEC JESD22-B102 and EN60749-21
Solderability
For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be
agreed upon with Melexis.
The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of
adhesive strength between device and board.
Melexis is contributing to global environmental conservation by promoting lead free solutions. For more
information on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of
the use of certain Hazardous Substances) please visit the quality page on our website:
http://www.melexis.com/quality.asp
13 ESD Precautions
Electronic semiconductor products are sensitive to Electro Static Discharge (ESD).
Always observe Electro Static Discharge control procedures whenever handling semiconductor products.
390107530301
Rev. 001
Page 12 of 13
Data Sheet
Mar/08
MLX75303
Optical Switch SensorEyeC
14 Disclaimer
Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its
Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis
reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product
is intended for use in normal commercial applications. Applications requiring extended temperature range,
unusual environmental requirements, or high reliability applications, such as military, medical life-support or
life-sustaining equipment are specifically not recommended without additional processing by Melexis for each
application.
The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be
liable to recipient or any third party for any damages, including but not limited to personal injury, property
damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data
herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis’ rendering of
technical or other services.
© 2005 Melexis NV. All rights reserved.
For additional information contact Melexis Direct:
Europe, Africa, Asia:
Phone: +32 1367 0495
E-mail: [email protected]
America:
Phone: +1 603 223 2362
E-mail: [email protected]
ISO/TS 16949 and ISO14001 Certified
390107530301
Rev. 001
Page 13 of 13
Data Sheet
Mar/08