SITRANS LVL200 Catalog Specification Sheet

© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
■ Overview
■ Configuration
Marked with screwed version on top,
with flange versions directed to the
flange holes
Horizontal mounting
Switching point
(recommended
mounting position,
particularly for
adhesive applications)
Vertical mounting
4
Switching point
with lower
density
SITRANS LVL200 is a standard vibrating level switch for material
detection in liquid and slurry applications such as overflow, high,
low, and demand applications, as well as pump protection.
For use in SIL-2 applications.
■ Benefits
• Proven vibrating level switch technology for liquids
• Compact insertion length of 40 mm (1.57 inch) for confined
space applications
• Fault monitoring for corrosion, loss of vibration or line break to
the piezo drive
• Functional Safety (SIL 2). Device suitable for use in accordance with IEC 61508 and IEC 61511
• Hygienic process connections
• Suitable for API 2350
Switching point
[approx.
27 (1.06)]
Switching point
[approx.
13 (0.51)]
Switching point
with higher
density
Mount away from filling
openings or agitators.
■ Application
SITRANS LVL200 is a level switch designed for industrial use in
all areas of process technology and can be used with liquids
and slurries. With a tuning fork insertion length of only 40 mm
(1.57 inch), SITRANS LVL200 can be mounted in small pipes
and applications with confined space. The LVL200 can be used
to measure products with a minimum density of > 0.5 g/cm³
(0.018 lb/in³). The LVL200 can be used in difficult conditions
including turbulence, air bubbles, foam generation, buildup, or
external vibration.
SITRANS LVL200 continuously monitors faults via frequency
evaluation, providing early detection of strong corrosion or damage on the tuning fork, loss of vibration, or a line break to the
piezo drive.
The tuning fork is piezoelectrically energized and vibrates at its
mechanical resonance frequency of approximately 1 200 Hz.
The vibration frequency changes when the tuning fork is
covered by the medium. This change is detected by the integrated oscillator and converted into a switching command. The
integrated electronics evaluate the level signal and output a
switching signal, directly operating connected devices.
• Key Applications: for use in liquids and slurries, for level
measurement, overfill, and dry run protection
Moisture protection
NOTE:
Welded socket for flush mount optional
Ensure cable gland
faces downward to
avoid water ingress.
SITRANS LVL200 installation, dimensions in mm (inch)
4/88
Siemens FI 01 · Update 05/2016
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
■ Technical specifications
Mode of operation
Measuring principle
Vibrating point level switch
Degree of protection
Type 4X/NEMA 4X/IP66/IP67
Conduit entry
• 1 x M20 x 1.5 (cable: ø5 ... 9 mm),
1 x blind stopper M20 x 1.5;
attached 1 x M20 x 1.5 cable entry
• 1 x ½" NPT cable entry, 1 x blind
stopper ½" NPT, 1 x ½" NPT cable
entry
• 1x M12 x 1; 1 x blind stopper
M20 x 1.5
Input
Measured variable
High and low and demand
(via mode switch)
Output
Output options
• Relay output (DPDT),
2 floating SPDTs
• Contactless electronic switch
• 2-wire Namur signal output
Measuring Accuracy
Repeatability
0.1 mm (0.004 inch)
Hysteresis
Approx. 2 mm (0.08 inch) with vertical installation
Switching delay
Approx. 500 ms (on/off)
Frequency
Approx. 1 200 Hz
Rated operating conditions
Indoor/outdoor
Ambient conditions
• Ambient temperature
-40 ... +70 °C (-40 ... +158 °F)
• Installation category
III
• Pollution degree
Power supply
Supply voltage
• Relay DPDT
• Contactless
2
Power consumption
• Relay DPDT
• Contactless
-50 ... +150 °C (-58 ... +302 °F)
-50 ... +250 °C (-58 ... +482 °F)
-50 ... +150 °C (-58 ... +302 °F)
-50 ... +250 °C (-58 ... +482 °F)
• Pressure (vessel)
-1 ... 64 bar g (-14.5 ... 928 psi g)
• Density
0.7 ... 2.5 g/cm³ (0.025 ... 0.09 lb/in³);
0.5 ... 2.5 g/cm³ (0.018 ... 0.09 lb/in³)
by switching over
Design
Material
• Enclosure
• Tuning fork
• Extension tube [ø 21.3 mm
(0.839 inch)]
• Process connection: threaded
• Process connection: flange
• Process seal
Process connection
• Pipe thread, cylindrical (ISO 228 T1)
• Pipe thread, tapered
• Flanges
• Hygienic fittings
20 ... 253 V AC, 50/60 Hz,
20 ... 72 V DC [at U > 60 V DC]
20 ... 253 V AC, 50/60 Hz,
20 ... 253 V DC
Operating voltage (characteristics
IEC 60947-5-6, approx. 8.2 V
according to standard) for connection Off-load voltage Uo approx. 8.2 V
to an amplifier according to NAMUR Short-circuit current IU approx.
8.2 mA
Medium conditions
• Temperature
- LVL200S Standard
- LVL200S High temperature option
- LVL200E Standard with 316L/
Alloy C22 (2.4602)
- LVL200E High temperature option
with 316L/Alloy C22 (2.4602)
Approx. 0.8 ... 4 kg
(0.18 ... 8.82 lb)
Approx. 920 g/m
(10 oz/ft)
• 2-wire NAMUR
Installation conditions
• Location
Weight
• Device weight
(dependent on process fitting)
• Tube extension
(extended version)
Aluminum die-cast AISi10Mg,
powder-coated, basis: Polyester
Stainless steel housing, electropolished 316L
316L (1.4404 or 1.4435),
Alloy C22 (2.4602)
316L (1.4404 or 1.4435),
Alloy C22 (2.4602)
316L (1.4404 or 1.4435),
Alloy C22 (2.4602)
316L (1.4404 or 1.4435), 316L with
Alloy C22 (2.4602), ECTFE, or PFA
coating
Klingersil C-4400
• 2-wire Namur
Certificates and approvals
1 ... 8 VA (AC), approx. 1.3 W (DC)
1 ... 8 VA (AC), approx. 1.3 W (DC)
Domestic current requirement
approx. 3 mA (via load circuit)
Load current
- Min. 10 mA
- Max. 400 mA [with I > 300 mA the
ambient temperature can be max.
60 °C (140 °F)]
- Max. 4 A up to 40 ms (not WHG
specified)
Current consumption
- Falling characteristics  2.6 mA
uncovered/ 0.6 mA covered
-  0.6 mA uncovered/ 2.6 mA
covered
- Failure message  0.6 mA
• CE, CSA
• Overfill Protection WHG
and VLAREM II
• FM (Non-Incendive) Class I, Div. 2,
Groups A, B, C, D
• FM (Explosion-Proof) Class I, Div. 1,
Groups A, B, C, D; (Dust IgnitionProof) Class II, III, Div. 1, Groups E,
F, G1
• IECEx d IIC T6 ... T2 Ga/Gb EHEDG
• ATEX II 1/2G, 2G EEx d IIC T6
• ATEX II 1G, 1/2G, 2G EEx ia IIC T6
Shipping approvals
• BR-Ex d IIC T6 ... T2
• FDA, 3A, Ehedge
• SIL/IEC61508 Declaration of Conformity [SIL-2 (min/max detection)]
G ¾" A, G 1" A
¾" NPT, 1" NPT, 1½" NPT
DIN from DN25, ANSI from 1"
Bolting DN 40 PN 40, 1, 1½, 2, 2½"
Tri-Clamp PN 10, conus DN 25 PN 40
Tuchenhagen Varivent DN 50 PN 10,
SMS
Siemens FI 01 · Update 05/2016
4/89
4
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
7 7 7 77 - 77 A 0
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Electronics
Contactless electronic switch 20 ... 250 V AC/DC11) 
Double relay (DPDT) 20 ... 72 V DC/20 ... 250 V AC 

NAMUR signal1)11)

Transistor (NPN/PNP) 10 ... 55 V DC
4
Approvals
Without approvals12)
Overfill protection (WHG)
ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG8)
1
2
4
5
Thread M27 x 1.5, PN 64/316L
Conus DN 25, PN 40/316L Ra < 0.3 µm
Conus DN 25, PN 40/316L Ra < 0.8 µm



A30
A31
A32
Conus DN 25, PN 40/ECTFE (ZB3033)4)
Conus M52, PN 40/316L
Conus M52, PN 40/316L Ra < 0.3 µm


A33
A34
A35
Conus M52, PN 40/316L Ra < 0.8 µm
Tri-Clamp 1", PN 16/316L Ra < 0.3 µm


A36
A37
Tri-Clamp 1", PN 16/Alloy C22 (2.4602)
Tri-Clamp 1", PN 16/316L Ra < 0.8 µm
Tri-Clamp 1½", PN 16/316L Ra < 0.3 µm



A38
A40
A4 1


A42



A
B
C
ATEX II 1/2G, 2G Ex d IIC T6 + WHG5)
ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + shipping
approvals8)
ATEX II 1/2G, 2G Ex d IIC T6 + shipping
approvals5)


D
E
Tri-Clamp 1½", PN 16/Alloy C22 (2.4602)

F
Tri-Clamp 1½", PN 16/316L Ra < 0.8 µm
Tri-Clamp 2", PN 16/316L Ra < 0.3 µm
Tri-Clamp 2", PN 16/Alloy C22 (2.4602)
ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + ATEX II 1/2 D
IP6X T8)9)
IECEx Ex ia IIC T68)
Shipping approvals

G


H
K
FM (IS) Class I, II, III, Div. 1, Groups A, B, C, D, E, F, 
G2)8)
FM (XP) Class I, Div. 1, Groups A, B, C, D; (DIP)

Class II, III, Div. 1, Groups E, F, G2)5)13)
2)
FM (NI) Class I, Div. 2, Groups A, B, C, D

N
IECEx d IIC T6...T2 Ga/Gb5)
CSA(XP)Class I, II, III Div. 1,
Groups A,B, C, D, E, F, G5)
CSA(NI)Class I, II, III, Div. 2,
Groups A, B, C, D, E, F, G
BR-Ex d IIC T6...T25)
CSA (IS) Class I, II, III Div. 1, Groups A, B, C, D, E,
F, G8)
Process connection
Thread G¾" A, PN 64/316L
Thread G¾" A, PN 64/316L Ra < 0.8 µm
Thread ¾" NPT, PN 64/316L
Thread ¾" NPT, PN 64/316L Ra < 0.8 µm
Thread ¾" NPT, PN 64/Alloy 400 (2.4360)
Thread G¾" A, PN 64/Alloy C22 (2.4602)
Thread ¾" NPT, PN 64/Alloy C22 (2.4602)
Thread G1" A, PN 64/316L
Thread G1" A, PN 64/316L ECTFE coated
MB19824)
Thread G1" A, PN 64/ 316L PFA coated4)
Thread G1" A, PN 64/ Alloy 400 (2.4360)
Thread G1" A, PN 64/ 316L Ra < 0.8 µm
Thread 1" NPT, PN 64/ 316L
Q


R
S

T


U
V










A00
A01
A02
A03
A04
A05
A06
A07
A08
A10
A11
A12
A13
A14
Thread 1" NPT, PN 64/ 316L ECTFE coated
MB19824)
Thread 1" NPT, PN 64 / 316L PFA-coated4)
Thread 1" NPT, PN 64 / Alloy 400 (2.4360)
A15
A16
Thread 1" NPT, PN 64 / 316L Ra < 0.8 µm
Thread G1" A, PN 64 / Alloy C22 (2.4602)


A17
A18
Thread G1" A, PN 64/Alloy C22 (2.4602)
Thread G1½" A, PN 64/316L
Thread G1½" A, PN 64/316L Ra < 0,8 µm



A20
A21
A22
Thread G1½" A, PN 64/Alloy C22 (2.4602)
Thread 1" NPT, PN 64/Alloy C22 (2.4602)
Thread 1½" NPT, PN 64/316L



A23
A24
A25
Thread 1½" NPT, PN 64/316L Ra < 0,8 µm
Thread 1½" NPT, PN 64/Alloy C22 (2.4602)
Thread G2" A, PN 64/316L



A26
A27
A28
4/90
Siemens FI 01 · Update 05/2016


A43
A44
A45



A46
A47
A48
Tri-Clamp 3", PN 10/316L Ra < 0.3 µm

Tri-Clamp 3", PN 10/316L Ra < 0.8 µm

Bolting DN 32, PN 40 DIN11851/316L Ra < 0.3 µm 
A50
A51
A52
Bolting DN 32, PN 40 DIN11851/316L Ra < 0.8 µm 
Bolting DN 25, PN 40 DIN11851/316L Ra < 0.3 µm 
Bolting DN 25, PN 40 DIN11851/316L Ra < 0.8 µm 
A53
A54
A55
Bolting DN 40, PN 40 DIN11851/316L Ra < 0.3 µm 
Bolting DN 40, PN 40 DIN11851/316L Ra < 0.8 µm 

Bolting DN 40, PN 40 DIN11864-1 A/316L
Ra < 0.8 µm ZB3052
A56
A57
A58
Bolting DN 50, PN 25 DIN11851/316L Ra < 0.3 µm 
Bolting DN 50, PN 25 DIN11851/316L Ra < 0.8 µm 
Bolting DN 50, PN 25 DIN11864-1 A/316L

Ra < 0.8 µm ZB3052
A60
A61
A62
Hygienic w. compr. nut F40, PN 25/316L
Hygienic w. compr. nut F40, PN 25/316L
Ra < 0.3 µm
Hygienic w. compr. nut F40, PN 25/316L
Ra < 0.8 µm




A63
A64
Varivent N50-40/316L Ra < 0.3 µm
Varivent N50-40/316L Ra < 0.8 µm
Varivent N125/100/316L Ra < 0.8 µm



A66
A67
A68
DRD flange, PN 40/316L ZB3007
SMS DN 38/316L Ra < 0.8 µm4)
SMS DN 51, PN 6/316L Ra < 0.8 µm4)



A70
A71
A72
Tri-Clamp 2", PN 16/316L Ra < 0.8 µm
Tri-Clamp 2½", PN 10/316L Ra < 0.3 µm
Tri-Clamp 2½", PN 10/316L Ra < 0.8 µm
P
7 7 7 77 - 77 A 0
A65
Swagelok VCR screwing ZG2579, PN 64/316L
Neumo biocontrol size 25, PN 16/316L Ra < 0.8 µm
Neumo biocontrol size 50, PN 16/316L Ra < 0.8 µm4)
A73
A74
A75
Neumo biocontrol size 65, PN 16/316L Ra < 0.8 µm
Neumo biocontrol size 80, PN 16/316L Ra < 0.8 µm
SÜDMO DN 50, PN 10/316L Ra<0,8µm
A76
A77
A78
Small flange DN 25, PN 1.5 DIN 28403/316L pol.
Ra < 0.8 µm
Small flange DN 40, PN 1.5 DIN 28403/316L pol.
Ra < 0.8 µm
Ingold connection, PN16 / 316L Ra < 0.8 µm
(acc. to MB2523)
A80
Ingold connection, PN 16/Alloy C22 (2.4602)
Terminal DN 33.7 PN 40 DIN11864-3-A-/316L BN2
Ra < 0.8 µm4)
Hygienic fl. DN 50 PN 16 DIN11864-2-A-/316L
Ra < 0.8 µm
A83
A84
A81
A82
A85
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
7 7 7 77 - 77 A 0
Flange DN 25, PN 6 Form C, DIN 2501/316L
Flange DN 25, PN 6 Form C, DIN 2501/PFA4)
Flange DN 25, PN 40 Form C, DIN 2501/316L
A86
A87
A88
Flange DN 25, PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 25, PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 25, PN 40 Form C, DIN 2501/PFA4)
B00
Flange DN 25, PN 40 Form C, DIN 2501/Enamelled
Flange DN 25, PN 40 Form D, DIN 2501/316L
Flange DN 25, PN 40 Form F, DIN 2501/316L
B03
B04
B05
Flange DN 25, PN 40 Form N, DIN 2501/316L
Flange DN 25, PN 40 Form N, DIN 2501/
Alloy C22 (2.4602)
Flange DN 25, PN 40 Form N, DIN 2501/
Alloy 400 (2.4360) solid
B06
B07
Flange DN 25, PN 40 V13, DIN 2501/316L
Flange DN 32, PN 40 Form C, DIN 2501/316L
Flange DN 32, PN 40 Form C, DIN 2501/ECTFE4)
B10
B11
B12
Flange DN 40, PN 6 Form C, DIN 2501/316L
Flange DN 40, PN 6 Form C, DIN 2501/ECTFE4)
Flange DN 40, PN 40 Form C, DIN 2501/316L
B13
B14
B15
Flange DN 40, PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 40, PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 40, PN 40 Form C, DIN 2501/PFA4)
B16
Flange DN 40, PN 40 Form C, DIN 2501/
Enamelled3)
Flange DN 40, PN 40 Form F, DIN 2501/316L
Flange DN 40, PN 40 Form N, DIN 2501/316L
B20
B01
B02
7 7 7 77 - 77 A 0
Flange DN 65, PN 64 Form E, DIN 2501/316L
B52
Flange DN 80, PN 40 Form C, DIN 2501/316L
Flange DN 80, PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 80, PN 40 Form C, DIN 2501/ECTFE4)
B53
B54
2501/PFA4)
B55
Flange DN 80, PN 40 Form C, DIN
Flange DN 80, PN 40 Form C, DIN 2501/
Enamelled3)
Flange DN 80, PN 40 Form F, DIN 2501/316L
B56
B57
Flange DN 80, PN 40 Form N, DIN 2501/316L
Flange DN 100, PN 16 Form C, DIN 2501/316L
Flange DN 100, PN 16 Form C, DIN 2501/
Alloy C22 (2.4602)
B60
B62
B63
Flange DN 100, PN 16 Form C, DIN 2501/ECTFE4)
Flange DN 100, PN 16 Form C, DIN 2501/PFA4)
Flange DN 100, PN 16 Form C, DIN 2501/
Enamelled3)
B64
B65
B66
Flange DN 100, PN 16 Form D, DIN 2501/316L
B67
Flange DN 100, PN 16 Form F, DIN 2501/316L
Flange DN 100, PN 16 Form N, DIN 2501/316L
Flange DN 100, PN 40 Form C, DIN 2501/316L
B68
B70
B71
Flange DN 100, PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 100, PN 40 Form C, DIN 2501/PFA4)
Flange DN 100, PN 40 Form C, DIN 2501/
Enamelled3)
B72
B73
B74
B21
B22
Flange DN 100, PN 40 Form F, DIN 2501/316L
Flange DN 100, PN 40 Form N, DIN 2501/316L
Flange DN 100, PN 40 V13, DIN 2501/316L
B75
B76
B77
Flange DN 40, PN 40 Form E, DIN 2501/316L
Flange DN 40, PN 40 V13, DIN 2501/316L
Flange DN 50, PN 40 Form C, DIN 2501/316L
B23
B24
B25
Flange DN 100, PN 64 Form E, DIN 2501/316L
Flange DN 100, PN 100 Form E, DIN 2501/316L
Flange DN 100, PN 100 Form L, DIN 2501/316L
B78
B80
B81
Flange DN 50, PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 50, PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 50, PN 40 Form C, DIN 2501/
ECTFE (ZB3108)4)
B26
Flange DN 125, PN 16 Form F, DIN 2501/316L
Flange DN 125, PN 40 Form C, DIN 2501/316L
Flange DN 125, PN 40 Form N, DIN 2512/ 316L
B82
B83
B84
B85
B86
Flange DN 50, PN 40 Form C, DIN 2501/PFA4)
Flange DN 50, PN 40 Form D, DIN 2501/316L
Flange DN 50, PN 40 Form D, DIN 2501/
Alloy C22 (2.4602)
B30
B31
B32
Flange DN 150, PN 16 Form C, DIN 2501/316L
Flange DN 150, PN 16 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 150, PN 16 Form C, DIN 2501/ECTFE4)
Flange DN 50, PN 40 Form F, DIN 2501/316L
Flange DN 50, PN 40 Form N, DIN 2501/316L
Flange DN 50, PN 40 Form N, DIN 2501/
Alloy C22 (2.4602)
B33
B34
B35
Flange DN 150, PN 16 Form C, DIN 2501/PFA4)
Flange DN 150, PN 16 Form D, DIN 2501/316L
Flange DN 150, PN 40 Form C, DIN 2501/316L
B88
C00
C01
C02
Flange DN 50, PN 40 Form E, DIN 2501/316L
Flange DN 50, PN 40 V13, DIN 2501/316L
Flange DN 50, PN 40 R13, DIN 2501/316L
B36
B37
B38
Flange DN 150, PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 150, PN 40 Form F, DIN 2501/316L
Flange DN 150, PN 40 Form N, DIN 2512/316L
Flange DN 50, PN 64 Form F, DIN 2501/316L
Flange DN 50, PN 64 Form N, DIN 2501/
Alloy C22 (2.4602)
Flange DN 50, PN 64 Form C, DIN 2501/316L
B40
B41
Flange DN 200, PN 10 Form C, DIN 2501/ECTFE4)
Flange DN 200, PN 16 Form C, DIN 2501/316L
Flange DN 25, PN 40 Form B1, EN 1092-1/316L
C05
C06
C07
C08
Flange DN 50, PN 64 Form L, DIN 2501/316L
Flange DN 50, PN 100 Form E, DIN 2501/316L
Flange DN 50, PN 100 Form L, DIN 2501/316L
B43
B44
B45
Flange DN 25, PN 40 Form B1, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 25, PN 40 Form B1, EN/ 316L/ PFA4)
Flange DN 25, PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 65, PN 40 Form C, DIN 2501/316L
Flange DN 65, PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 65, PN 40 Form C, DIN 2501/ECTFE4)
B46
B47
Flange DN 25, PN 40 Form B2, EN 1092-1/316L
Flange DN 25, PN 40 Form F, EN 1092-1/316L
Flange DN 25, PN 63 Form B1, EN 1092-1/316L
C12
C13
C14
Flange DN 65, PN 40 Form C, DIN 2501/PFA4)
Flange DN 65, PN 40 Form F, DIN 2501/316L
B50
B51
Flange DN 25, PN 100 Form B2, EN 1092-1/316L
Flange DN 40, PN 40 Form B1, EN/ 316L
Flange DN 40, PN 40 Form B1, EN 1092-1/PFA4)
C15
C16
C17
Flange DN 40, PN 40 Form B2, EN/316L
Flange DN 50, PN 40 Form B1, EN/316L
C18
C20
B08
B17
B18
B27
B28
B42
B48
B58
4
B87
C03
C04
C10
C11
Siemens FI 01 · Update 05/2016
4/91
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
4
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
7 7 7 77 - 77 A 0
7 7 7 77 - 77 A 0
Flange DN 50, PN 40 Form B1, EN 1092-1/
Alloy C22 (2.4602)
C21
Flange 2" 150 lb RF, ANSI B16.5/Alloy 400 (2.4360)
ZB2977
C74
Flange DN 50, PN 40 Form B1, EN 1092-1/
Alloy 400 (2.4360) ZB2977
Flange DN 50, PN 40 Form B1, EN 1092-1/ECTFE4)
Flange DN 50, PN 40 Form B1, EN/ 316L/PFA4)
C22
Flange 2" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 2" 150 lb RF, ANSI B16.5/PFA4)
Flange 2" 150 lb RF, ANSI B16.5/Enamelled3)
C75
C76
C77
Flange DN 50, PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 50, PN 40 Form C, EN 1092-1/316L
Flange DN 50, PN 40 Form D, EN/316L
C25
Flange 2" 150 lb FF, ANSI B16.5/316L
Flange 2" 150 lb FF, ANSI B16.5/ECTF4)
Flange 2" 150 lb SG (small groove),
ANSI B16.5/316L
C78
C80
C81
Flange DN 50, PN 40 Form D, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 50, PN 40 Form B2, EN 1092-1/316L
Flange DN 50, PN 40 Form E, EN 1092-1/316L
C28
Flange 2" 300 lb RF, ANSI B16.5/316L
Flange 2" 300 lb RF, ANSI B16.5/Alloy C22 (2.4602)
C82
C83
C30
C31
Flange DN 80, PN 40 Form B1, EN 1092-1/316L
Flange DN 80, PN 40 Form B1, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 80, PN 40 Form B1, EN 1092-1/ECTFE4)
C32
C33
Flange 2" 300 lb RF, ANSI B16.5/ECTFE4)
Flange 2" 300 lb RF, ANSI B16.5/PFA4)
Flange 2" 300 lb RF, ANSI B16.5 Enamelled3)
C85
C86
C87
C88
D00
D01
Flange DN 80, PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 80, PN 40 Form B2, EN 1092-1/316L
Flange DN 100, PN 16 Form B1, EN 1092-1/316L
C35
Flange 2" 300 lb RJF, ANSI B16.5/316L
Flange 2" 300 lb ST, ANSI B16.5/316L
Flange 2" 300 lb LG (large groove),
ANSI B16.5/316L
D02
D03
D04
Flange DN 100, PN 16 Form B1, EN 1092-1/
Alloy C22 (2.4602)
C38
Flange 2" 300 lb LT, ANSI B16.5/316L
Flange 2" 600 lb RF, ANSI B16.5/316L
Flange 2" 600 lb RF, ANSI B16.5/Alloy 400 (2.4360)
ZB2977
Flange DN 100, PN 16 Form B1, EN 1092-1/
Enamelled3)
Flange DN 100, PN 40 Form B1, EN 1092-1/316L
Flange DN 100, PN 40 Form B1, EN 1092-1/
Enamelled3)
C40
Flange 2" 600 lb RF, ANSI B16.5/ECTFE4)
Flange 2" 600 lb RJF, ANSI B16.5/316L
Flange 2" 600 lb LG, ANSI B16.5/316L
D05
D06
D07
C41
C42
Flange 2" 900 lb RJF, ANSI B16.5/316L
Flange 2½" 150 lb RF, ANSI B16.5/316L
Flange 2½" 300 lb RF, ANSI B16.5/316L
D08
D10
D11
Flange DN 100, PN 40 Form C, EN 1092-1/316L
Flange DN 100, PN 63 Form B2, EN 1092-1/316L
Flange DN 150, PN 16 Form B1, EN 1092-1/316L
C43
C44
C45
Flange 3" 150 lb RF, ANSI B16.5/316L
Flange 3" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 3" 150 lb RF, ANSI B16.5/ECTFE4)
D12
D13
D14
Flange DN 150, PN 16 Form B1, EN 1092-1/PFA4)
Flange DN 150, PN 40 Form B1, EN 1092-1/316L
C46
C47
Flange 3" 150 lb RF, ANSI B16.5/PFA4)
Flange 3" 150 lb RF, ANSI B16.5/Enamelled3)
D15
D16
Flange DN 150, PN 40 Form B1, EN 1092-1/ECTFE4)
Flange DN 150, PN 40 Form B2, EN 1092-1/316L
Flange 1" 150 lb ANSI B16.5/316L
C48
Flange 3" 150 lb FF, ANSI B16.5/316L
D17
C50
C51
Flange 3" 150 lb FF, ANSI B16.5/ECTFE4)
Flange 3" 150 lb FF, ANSI B16.5/PFA4)
Flange 3" 300 lb RF, ANSI B16.5/316L
D18
D20
D21
Flange 1" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 1" 150 lb RF, ANSI B16.5/Alloy 400 (2.4360)
ZB2977
Flange 1" 150 lb RF, ANSI B16.5/ECTFE4)
C52
C53
Flange 3" 300 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 3" 300 lb RF, ANSI B16.5/ECTFE4)
Flange 3" 300 lb RF, ANSI B16.5/PFA4)
D22
D23
D24
Flange 1" 150 lb RF, ANSI B16.5/PFA4)
Flange 1" 150 lb RF, ANSI B16.5/Enamelled3)
Flange 1" 300 lb RF, ANSI B16.5/316L
C55
C56
C57
Flange 3" 300 lb RF, ANSI B16.5/Enamelled3)
Flange 3" 600 lb RF, ANSI B16.5/316L
Flange 3½" 150 lb RF, ANSI B16.5/316L
D25
D26
D27
Flange 1" 300 lb RF, ANSI B16.5/ECTFE4)
Flange 1" 600 lb RF, ANSI B16.5/316L
Flange 1½" 150 lb RF, ANSI B16.5/316L
C58
C60
C61
Flange 3½" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 4" 150 lb RF, ANSI B16.5/316L
Flange 4" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
D28
D30
D31
Flange 1½" 150 lb RF, ANSI B16.5/
Alloy C22 (2.4602)
Flange 1½" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 1½" 150 lb RF, ANSI B16.5/PFA4)
C62
Flange 4" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 4" 150 lb RF, ANSI B16.5/PFA4)
Flange 4" 150 lb RF, ANSI B16.5/Enamelled3)
D32
D33
D34
Flange 4" 150 lb LT, ANSI B16.5/316L
Flange 4" 300 lb RF, ANSI B16.5/316L
Flange 4" 300 lb RF, ANSI B16.5/Alloy C22 (2.4602)
D35
D36
D37
Flange 4" 300 lb RF, ANSI B16.5/ECTFE4)
Flange 4" 300 lb RJF, ANSI B16.5/316L
Flange 4" 300 lb LG, ANSI B16.5/316L
D38
D40
D41
Flange 4" 300 lb LT, ANSI B16.5/316L
Flange 4" 600 lb RF, ANSI B16.5/316L
Flange 4" 600 lb RJF, ANSI B16.5/316L
D42
D43
D44
Flange 6" 150 lb RF, ANSI B16.5/316L
Flange 6" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
D45
D46
Enamelled3)
C23
C24
C26
C27
C34
C36
C37
C54
C63
C64
Flange 1½" 150 lb RF, ANSI B16.5
Flange 1½" 150 lb FF, ANSI B16.5/ECTFE4)
Flange 1½" 300 lb RF, ANSI B16.5/316L
C65
C66
C67
Flange 1½" 300 lb RF, ANSI B16.5/
Alloy 400 (2.4360) ZB2977
Flange 1½" 300 lb RF, ANSI B16.5/ECTFE3)
Flange 1½" 600 lb RF, ANSI B16.5/316L
C68
Flange 2" 150 lb RF, ANSI B16.5/316L
Flange 2" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
C72
C73
4/92
Siemens FI 01 · Update 05/2016
C70
C71
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Selection and Ordering data
Article No.
Selection and Ordering data
Order code
SITRANS LVL200, Standard
Compact vibrating level switch for material detection in liquid and slurry applications such as overflow, high, low, and demand applications, as well as
pump protection. For use in SIL-2 and hazardous
applications.
7ML5746-
3.1-Inspection Certificate for instrument with test
data (EN 10204)
C25
Quality and test plan
C26
Pressure test + 3.1 certificate/instrument10)
C31
Helium leak test + 3.1 certificate/instrument10)
C32
Ferrite measuring accuracy to DIN32514-1
+ 3.1 certificate/instrument10)
C60
Pressure test according to Norsok
+ 3.1 certificate/instrument10)
C61
Operating Instructions
Article No.
Flange 6" 150 lb RF, ANSI
7 7 7 77 - 77 A 0
B16.5/ECTFE4)
D47
B16.5/PFA4)
Flange 6" 150 lb RF, ANSI
Flange 6" 150 lb RJF, ANSI B16.5/316L
Flange 6" 300 lb RF, ANSI B16.5/316L
D48
D50
D51
Flange 8" 150 lb RF, ANSI B16.5/316L
Flange 8" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 1" BS.10 Table E/316L
D52
D53
D54
Flange 1" BS.10 Table E/PFA4)
Flange 1½" BS.10 Table E/316L
Flange 3½" BS.10 Table E/316L
D55
D56
D57
• English
7ML1998-5KR01
• German
7ML1998-5KR31
Flange 4" BS.10 Table
Flange DN 40 10K, JIS/316L
Flange DN 50 10K, JIS/316L
D58
D60
D61
LVL200 (Contactless electronic switch)
Flange DN 80 10K, JIS/316L
Flange DN 100 10K, JIS/316L
Thread R1 PN 64, EN 10226-1/316L
D62
D63
D65
E/ECTFE4)
Adapter/Process temperature
Without adapter/-50 ... +150 °C (-58 ... +302 °F)
With adapter/-50 ... +200 °C (-58 ... +392 °F)
With adapter/-50 .... +250 °C (-58 ... +482 °F)
With gas-tight leadthrough/-50 ... +150 °C
(-58 ... +302 °F)
With gas-tight leadthrough/-50 ... +250 °C
(-58 ... +482 °F)
Housing/Cable entry
Aluminum IP66/IP67/M20 x 1.5
Aluminum IP66/IP67/½" NPT
316L stainless steel (electropolished)
IP66/IP67/M20 x 1.5
316L stainless steel (electropolished)
IP66/IP67/½" NPT
Aluminum IP66/IP67/M20 x 1.5 Special HARTING
plug (bent) according to Tier One (ZB7555)
Selection and Ordering data
LVL200 (DPDT Relay)
1
2
3

4

5


• German
7ML1998-5KQ31
D
V
Order code
• English
7ML1998-5LS01
• German
7ML1998-5LS31
Note: The Operating Instructions should be
ordered as a separate line item on the order.
All literature is available to download for free, in a
range of languages, at http://www.siemens.com/
processinstrumentation/documentation
This device is shipped with the Siemens Level and
Weighing manual DVD containing the Operating
Instructions library.
A
B
C
Please add "-Z" to Article No. and specify Order
code(s).
7ML1998-5KQ01
Electronics module LVL200 Relay



Further designs
• English
Spare Parts and Accessories
Electronics module SITRANS LVL200 Relay
7ML1830-1NC
Electronics module SITRANS LVL200 Contactless
7ML1930-6AA
NAMUR spare electronics module
LVL200 Threaded Welded Socket
A5E35817107
• G¾" A/316L with FKM Seal
7ML1930-1EE
• G1" A/316L with FKM Seal
7ML1930-1EF
• M27 x 1.5/316L with FKM Seal
7ML1930-1EG
• G¾" A/316L with EPDM Seal
7ML1930-1EH
• G1" A/316L with EPDM Seal
7ML1930-1EJ
Cleaning including Certificate
(oil, grease, and silicone free)
W01
• M27 x 1.5/316L with EPDM Seal
7ML1930-1EK
Identification label (measurement loop) stainless
steel: max. 40 characters, add in plain text.
To add more than one line, use a coma “,” for line
break.
Y17
1)
Identification Label (measurement loop) foil:
max. 40 characters add in plain text.
To add more than one line, use a coma “,” for line
break.
Y18
3.1-Inspection Certificate for material (EN 10204
NACE MR 0175)10)
D07
2.2-Factory certificate for material (EN 10204)10)
C15
Functional Safety (SIL 2). Device suitable for use in
accordance with IEC 61508 and IEC 6151110)
C20
Dye penetration test + 3.1 certificate/instrument10)
C13
X-ray test + 3.1 certificate/instrument10)
C14
Positive material identification test
+ 3.1 certificate/instrument10)
C16
Roughness test + 3.1 certificate/instrument10)
C18
3.1-Inspection Certificate for instrument
(EN 10204)
C12
Only available with Adapter/Process temperature options 1, 3, 4, and 5
Only available with housing option B
3) Available with Adapter/Process temperature options 1, 2, and 4
4)
Not in combination with adapter/Process temperature options 2, 3, and 5
5)
Not in combination with adapter/Process temperature options 2, 4, and 5
8) Only available with Electronics options 4 and 5
9)
Not in combination with Process Connection/Material options ECTFE Coated
Probes
10)
Listed Certificates are not available with all configurations please contact
factory for more information
11) Not available with Electric Options 0, 1, 3, 4, 5, 6, and Housing/Protection/
Cable Option V
12)
Available with Housing/Protection/Cable options V
13)
Approval option P is not available with PFA and ECTFE coating options
2)
We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Siemens FI 01 · Update 05/2016
4/93
4
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
77 7 77 - 77 77
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Electronics
Contactless electronic switch 20 ... 250 V AC/DC13)
Double relay (DPDT) 20 ... 72 V DC/20 ... 250 V AC
NAMUR signal1)13)
Transistor (NPN/PNP) 10 ... 55 V DC
4
Approvals
Without approvals14)
Overfill protection (WHG)
ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG8)
1
2
4
5
A
B
C
ATEX II 1/2G, 2G Ex d IIC T6 + WHG5)9)
ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + shipping
approvals8)
ATEX II 1/2G, 2G Ex d IIC T6 + shipping approvals5)9)
D
E
ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + ATEX II 1/2D
IP6X T8)11)
IECEx Ex ia IIC T68)
Shipping approvals
G
FM (IS) Class I, II, III, Div. 1, Groups A, B, C, D, E, F, G 2)8)
FM (XP) Class I, Div. 1, Groups A, B, C, D; (DIP)
Class II, III, Div. 1, Groups E, F, G2)5)9)15)
N
P
FM (NI) Class I, Div. 2, Groups A, B, C, D2)
IECEx d IIC T6 ... T2 Ga/Gb5)9)
CSA(XP) Class I,II,III Div. 1,
Groups A, B, C, D, E, F, G5)9)
Q
R
S
CSA(NI)Class I,II,III, Div. 2,
Groups A, B, C, D, E, F, G
BR-Ex d IIC T6 ... T25)
CSA (IS) Class I, II, III Div. 1,
Groups A, B, C, D, E, F, G8)
T
F
H
K
U
V
Process connection
7 7 7 77 - 77 7 7
Cyl. socket/316Ti/1.4581 ECTFE coated ZB29844)
Conus DN 25 PN 40/316L Ra < 0.3 µm
Conus DN 25 PN 40/316L Ra < 0.8 µm.
A31
A32
A33
Conus DN 25 PN 40/ECTFE (ZB3033)4)
Conus M52 PN 40/316L
Conus M52 PN 40/316L Ra < 0.3 µm
A34
A35
A36
Conus M52 PN 40/316L Ra < 0.8 µm
Tri-Clamp 1" PN 16/316L Ra < 0.3 µm
Tri-Clamp 1" PN 16/Alloy C22 (2.4602)
A37
A38
A40
Tri-Clamp 1" PN 16/316L Ra < 0.8 µm
Tri-Clamp 1½" PN 16/316L Ra < 0.3 µm
Tri-Clamp 1½" PN 16/Alloy C22 (2.4602)
A41
A42
A43
Tri-Clamp 1½" PN 16/316L Ra < 0.8 µm
Tri-Clamp 2" PN 16/316L Ra < 0.3 µm
Tri-Clamp 2" PN 16/Alloy C22 (2.4602)
A44
A45
A46
Tri-Clamp 2" PN 16/316L Ra < 0.8 µm
Tri-Clamp 2½" PN 10/316L Ra < 0.3 µm
Tri-Clamp 2½" PN 10/316L Ra < 0.8 µm
A47
A48
A50
Tri-Clamp 3" PN 10/316L Ra < 0.3 µm
Tri-Clamp 3" PN 10/316L Ra < 0.8 µm
Bolting DN 32 PN 40 DIN11851/316L Ra < 0.3 µm
A51
A52
A53
Bolting DN 32 PN 40 DIN11851/316L Ra < 0.8 µm
Bolting DN 25 PN 40 DIN11851/316L Ra < 0.3 µm
Bolting DN 25 PN 40 DIN11851/316L Ra < 0.8 µm
A54
A55
A56
Bolting DN 40 PN 40 DIN11851/316L Ra < 0.3 µm
Bolting DN 40 PN 40 DIN11851/316L Ra < 0.8 µm
Bolting DN 40 PN 40 DIN11864-1 A/316L
Ra < 0.8 µm ZB3052
A57
A58
A60
Bolting DN 50 PN 25 DIN11851/316L Ra < 0.3 µm
Bolting DN 50 PN 25 DIN11851/316L Ra < 0.8 µm
Bolting DN 50 PN 25 DIN11864-1 A/316L
Ra < 0.8 µm ZB3052
A61
A62
A63
Thread G¾" A, PN 64/316L
Thread G¾" A, PN 64/316L Ra < 0.8 µm
Thread ¾" NPT, PN 64/316L
A00
A01
A02
Hygienic w.compr.nut F40 PN 25/316L
Hygienic w.compr.nut F40 PN 25/316L Ra < 0.3 µm
Hygienic w.compr.nut F40 PN 25/316L Ra < 0.8 µm
A64
A65
A66
Thread ¾" NPT, PN 64/316L Ra < 0.8 µm
Thread ¾" NPT, PN 64/Alloy 400 (2.4360)
Thread G¾" A, PN 64/Alloy C22 (2.4602)
A03
A04
A05
Varivent N50-40/316L Ra < 0.3 µm
Varivent N50-40/316L Ra < 0.8 µm
Varivent N125/100/316L Ra < 0.8 µm
A67
A68
A70
Thread ¾" NPT, PN 64/Alloy C22 (2.4602)
Thread G1" A, PN 64/316L
Thread G1" A, PN 64/316L ECTFE coated
MB19824)
A06
A07
A08
DRD flange PN 40/316L ZB3007
SMS DN 38/316L Ra < 0.8 µm4)
SMS DN 51 PN 6/316L Ra < 0.8 µm4)
A71
A72
A73
Thread G1" A, PN 64/316L PFA coated4)
Thread G1" A, PN 64/Alloy 400 (2.4360)
Thread G1" A, PN 64/316L Ra < 0.8 µm
A10
A11
A13
Swagelok VCR screwing ZG2579 PN 64/316L
Neumo biocontrol size 25 PN 16/316L Ra < 0.8 µm
Neumo biocontrol size 50 PN 16/316L Ra < 0.8 µm
A74
A75
A76
Thread 1" NPT, PN 64/316L
Thread 1" NPT, PN 64/316L ECTFE coated MB19824)
Thread 1" NPT, PN 64/316L PFA coated4)
A14
A15
A16
Neumo biocontrol size 65 PN 16/316L Ra < 0.8 µm
Neumo biocontrol size 80 PN 16/316L Ra < 0.8 µm
SÜDMO DN 50 PN 10/316L Ra < 0.8 µm
A77
A78
A80
A17
A18
A20
Thread G1½" A, PN 64/316L
Thread G1½" A, PN 64/316L Ra <0.8 µm
Thread G1½" A, PN 64/Alloy C22 (2.4602)
A21
A22
A23
Small flange DN 25 PN 1.5 DIN 28403/316L pol.
Ra < 0.8 µm
Small flange DN 40 PN 1.5 DIN 28403/316L pol.
Ra < 0.8 µm
Ingold connection PN 16/316L Ra < 0.8 µm
A81
Thread 1" NPT, PN 64/Alloy 400 (2.4360)
Thread 1" NPT, PN 64/316L Ra < 0.8 µm
Thread G1" A, PN 64/Alloy C22 (2.4602)
A84
Thread 1" NPT, PN 64/Alloy C22 (2.4602)
Thread 1½" NPT, PN 64/316L
Thread 1½" NPT, PN 64/316L Ra< 0.8 µm
A24
A25
A26
Collar clamp connection DN33,7 PN40 Form A,
DIN11864-3/1.4435 (BN2, Ra < 0.8 µm)
Collar flange DN50 PN16 Form A, DIN11864-2/
316L (Ra < 0.8 µm)
Flange DN 25 PN 6 Form C, DIN 2501/316L
Thread 1½" NPT, PN 64/Alloy C22 (2.4602)
Thread G2" A, PN 64/316L
Thread M27 x 1.5 PN 64/316L
A27
A28
A30
4/94
Siemens FI 01 · Update 05/2016
A82
A83
A85
A86
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
Flange DN 25 PN 6 Form C, DIN 2501/PFA4)
Flange DN 25 PN 40 Form C, DIN 2501/316L
Flange DN 25 PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
2501/ECTFE4)
77 7 77 - 77 77
A87
A88
B00
Flange DN 25 PN 40 Form C, DIN
Flange DN 25 PN 40 Form C, DIN 2501/PFA4)
Flange DN 25 PN 40 Form D, DIN 2501/316L
B01
B02
B03
Flange DN 25 PN 40 Form F, DIN 2501/316L
Flange DN 25 PN 40 Form N, DIN 2501/316L
Flange DN 25 PN 40 Form N, DIN 2501/
Alloy C22 (2.4602)
B04
B05
B06
Flange DN 25 PN 40 Form N, DIN 2501/
Alloy 400 (2.4360) solid
Flange DN 25 PN 40 V13, DIN 2501/316L
B07
Flange DN 32 PN 40 Form C, DIN 2501/316L
B10
Flange DN 32 PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 40 PN 6 Form C, DIN 2501/316L
Flange DN 40 PN 6 Form C, DIN 2501/ECTFE4)
B11
B12
B13
Flange DN 40 PN 40 Form C, DIN 2501/316L
Flange DN 40 PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 40 PN 40 Form C, DIN 2501/ECTFE4)
B14
B15
2501/PFA4)
B08
B16
7 7 7 77 - 77 7 7
Flange DN 80 PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
B53
Flange DN 80 PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 80 PN 40 Form C, DIN 2501/PFA4)
Flange DN 80 PN 40 Form F, DIN 2501/316L
B54
B55
B56
Flange DN 80 PN 40 Form N, DIN 2501/316L
Flange DN 80 PN 40 Form N, DIN 2501/
Alloy C22 (2.4602)
Flange DN 100 PN 16 Form C, DIN 2501/316L
B57
B58
Flange DN 100 PN 16 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 100 PN 16 Form C, DIN 2501/ECTFE4)
Flange DN 100 PN 16 Form C, DIN 2501/PFA4)
B61
Flange DN 100 PN 16 Form D, DIN 2501/316L
Flange DN 100 PN 16 Form F, DIN 2501/316L
Flange DN 100 PN 16 Form N, DIN 2501/316L
B64
B65
B66
Flange DN 100 PN 40 Form C, DIN 2501/316L
Flange DN 100 PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 100 PN 40 Form C, DIN 2501/PFA4)
B67
B68
B70
Flange DN 100 PN 40 Form C, DIN 2501/
Enamelled3)
Flange DN 100 PN 40 Form F, DIN 2501/316L
Flange DN 100 PN 40 Form N, DIN 2501/316L
B71
B74
B75
B76
B60
B72
B73
Flange DN 40 PN 40 Form C, DIN
Flange DN 40 PN 40 Form C, DIN 2501/Enamelled3)
Flange DN 40 PN 40 Form F, DIN 2501/316L
B17
B18
B20
Flange DN 100 PN 40 V13, DIN 2501/316L
Flange DN 100 PN 64 Form E, DIN 2501/316L
Flange DN 100 PN 100 Form E, DIN 2501/316L
Flange DN 40 PN 40 Form N, DIN 2501/316L
Flange DN 40 PN 40 Form E, DIN 2501/316L
Flange DN 40 PN 40 V13, DIN 2501/316L
B21
B22
B23
Flange DN 100 PN 100 Form L, DIN 2501/316L
Flange DN 125 PN 16 Form F, DIN 2501/316L
Flange DN 125 PN 40 Form C, DIN 2501/316L
B77
B78
B80
Flange DN 50 PN 40 Form C, DIN 2501/316L
Flange DN 50 PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 50 PN 40 Form C, DIN 2501/ECTFE4)
B24
B25
Flange DN 125 PN 40 Form N, DIN 2512/316L
Flange DN 150 PN 16 Form C, DIN 2501/316L
Flange DN 150 PN 16 Form C, DIN 2501/
Alloy C22 (2.4602)
B81
B82
B83
Flange DN 50 PN 40 Form C, DIN 2501/ECTFE
(ZB3108)4)
Flange DN 50 PN 40 Form C, DIN 2501/PFA4)
Flange DN 50 PN 40 Form D, DIN 2501/316L
B27
Flange DN 150 PN 16 Form C, DIN 2501/ECTFE4)
Flange DN 150 PN 16 Form C, DIN 2501/PFA4)
Flange DN 150 PN 16 Form D, DIN 2501/316L
B84
B85
B86
Flange DN 50 PN 40 Form D, DIN 2501/
Alloy C22 (2.4602)
Flange DN 50 PN 40 Form F, DIN 2501/316L
Flange DN 50 PN 40 Form N, DIN 2501/316L
B31
Flange DN 150 PN 40 Form C, DIN 2501/316L
Flange DN 150 PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
Flange DN 150 PN 40 Form F, DIN 2501/316L
B87
B88
Flange DN 50 PN 40 Form N, DIN 2501/
Alloy C22 (2.4602)
Flange DN 50 PN 40 Form E, DIN 2501/316L
Flange DN 50 PN 40 V13, DIN 2501/316L
B34
Flange DN 150 PN 40 Form N, DIN 2512/316L
Flange DN 200 PN 10 Form C, DIN 2501/ECTFE4)
Flange DN 200 PN 16 Form C, DIN 2501/316L
C01
C02
C03
C04
C05
Flange DN 50 PN 40 R13, DIN 2501/316L
Flange DN 50 PN 64 Form F, DIN 2501/316L
Flange DN 50 PN 64 Form N, DIN 2501/
Alloy C22 (2.4602)
B37
B38
B40
Flange DN 25 PN 40 Form B1, EN 1092-1/316L
Flange DN 25 PN 40 Form B1, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 25 PN 40 Form B1, EN/316L/PFA4)
C07
Flange DN 50 PN 64 Form C, DIN 2501/316L
Flange DN 50 PN 64 Form L, DIN 2501/316L
Flange DN 50 PN 100 Form E, DIN 2501/316L
B41
B42
B43
Flange DN 25 PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 25 PN 40 Form B2, EN 1092-1/316L
Flange DN 25 PN 40 Form F, EN 1092-1/316L
Flange DN 50 PN 100 Form L, DIN 2501/316L
Flange DN 65 PN 40 Form C, DIN 2501/316L
Flange DN 65 PN 40 Form C, DIN 2501/
Alloy C22 (2.4602)
B44
B45
B46
Flange DN 25 PN 63 Form B1, EN 1092-1/316L
Flange DN 25 PN 100 Form B2, EN 1092-1/316L
Flange DN 40 PN 40 Form B1, EN/316L
C11
C12
C13
Flange DN 65 PN 40 Form C, DIN 2501/ECTFE4)
Flange DN 65 PN 40 Form C, DIN 2501/PFA4)
Flange DN 65 PN 40 Form F, DIN 2501/316L
B47
B48
B50
Flange DN 40 PN 40 Form B1, EN 1092-1/PFA4)
Flange DN 40 PN 40 Form B2, EN/316L
Flange DN 50 PN 40 Form B1, EN/316L
C14
C15
C16
C17
Flange DN 65 PN 64 Form E, DIN 2501/316L
Flange DN 80 PN 40 Form C, DIN 2501/316L
B51
B52
Flange DN 50 PN 40 Form B1, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 50 PN 40 Form B1,EN 1092-1/
Alloy 400 (2.4360) ZB2977
Flange DN 50 PN 40 Form B1, EN 1092-1/ECTFE4)
B26
B28
B30
B32
B33
B35
B36
4
B62
B63
C00
C06
C08
C10
C18
C20
Siemens FI 01 · Update 05/2016
4/95
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
4
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
77 7 77 - 77 77
Flange DN 50 PN 40 Form B1, EN/316L/PFA4)
Flange DN 50 PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 50 PN 40 Form C, EN 1092-1/316L
C21
C22
Flange DN 50 PN 40 Form D, EN/316L
Flange DN 50 PN 40 Form D, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 50 PN 40 Form B2, EN 1092-1/316L
C24
C25
Flange DN 50 PN 40 Form E, EN 1092-1/316L
Flange DN 80 PN 40 Form B1, EN 1092-1/316L
Flange DN 80 PN 40 Form B1, EN 1092-1/
Alloy C22 (2.4602)
C27
C28
C30
Flange DN 80 PN 40 Form B1, EN 1092-1/ECTFE4)
Flange DN 80 PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 80 PN 40 Form B2, EN 1092-1/316L
C31
C32
Flange DN 100 PN 16 Form B1, EN 1092-1/316L
Flange DN 100 PN 16 Form B1, EN 1092-1/
Alloy C22 (2.4602)
Flange DN 100 PN 16 Form B1, EN 1092-1/
Enamelled3)
C34
C35
Flange DN 100 PN 40 Form B1, EN 1092-1/316L
Flange DN 100 PN 40 Form B1, EN 1092-1/
Enamelled3)
Flange DN 100 PN 40 Form C, EN 1092-1/316L
C37
C38
Flange DN 100 PN 63 Form B2, EN 1092-1/316L
Flange DN 150 PN 16 Form B1, EN 1092-1/316L
Flange DN 150 PN 16 Form B1, EN 1092-1/PFA4)
C41
C42
C43
Flange DN 150 PN 40 Form B1, EN 1092-1/316L
Flange DN 150 PN 40 Form B1, EN 1092-1/ECTFE4)
Flange DN 150 PN 40 Form B2, EN 1092-1/316L
Flange 1" 150 lb ANSI B16.5/316L
Flange 1"150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 1"150 lb RF, ANSI B16.5//Alloy 400 (2.4360)
ZB2977
C47
C48
C50
Flange 2" 150 lb FF, ANSI B16.5/ECTFE4)
C76
Flange 2" 150 lb SG (small groove),
ANSI B16.5/316L
Flange 2" 300 lb RF, ANSI B16.5/316L
Flange 2" 300 lb RF, ANSI B16.5/Alloy C22 (2.4602)
C77
Flange 2" 300 lb RF, ANSI B16.5/ECTFE4)
Flange 2" 300 lb RF, ANSI B16.5/PFA4)
Flange 2" 300 lb RJF, ANSI B16.5/316L
Flange 2" 300 lb ST, ANSI B16.5/316L
C82
C83
C85
C86
Flange 2" 300 lb LG (large groove),
ANSI B16.5/316L
Flange 2" 300 lb LT, ANSI B16.5/316L
Flange 2" 600 lb RF, ANSI B16.5/316L
C87
Flange 2" 600 lb RF, ANSI B16.5/Alloy 400 (2.4360)
ZB2977
Flange 2" 600 lb RF, ANSI B16.5/ECTFE4)
Flange 2" 600 lb RJF, ANSI B16.5/316L
D01
Flange 2" 600 lb LG, ANSI B16.5/316L
Flange 2" 900 lb RJF, ANSI B16.5/316L
Flange 2½" 150 lb RF, ANSI B16.5/316L
D04
D05
D06
Flange 2½" 300 lb RF, ANSI B16.5/316L
Flange 3" 150 lb RF, ANSI B16.5/316L
D07
D08
Flange 3" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
D10
Flange 3" 150 lb RF, ANSI B16.5/Alloy 400 (2.4360)
ZB2977
Flange 3" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 3" 150 lb RF, ANSI B16.5/PFA4)
D11
C44
C45
Flange 3" 150 lb RF, ANSI B16.5/Enamelled3)
Flange 3" 150 lb FF, ANSI B16.5/316L
Flange 3" 150 lb FF, ANSI B16.5/ECTFE4)
D14
D15
D16
C46
Flange 3" 150 lb FF, ANSI B16.5/PFA4)
Flange 3" 300 lb RF, ANSI B16.5/316L
Flange 3" 300 lb RF, ANSI B16.5/Alloy C22 (2.4602)
D17
D18
D20
Flange 3" 300 lb RF, ANSI B16.5/ECTFE4)
Flange 3" 300 lb RF, ANSI B16.5/PFA4)
Flange 3" 300 lb RF, ANSI B16.5/Enamelled3)
D21
D22
D23
Flange 3" 600 lb RF, ANSI B16.5/316L
Flange 3½" 150 lb RF, ANSI B16.5/316L
Flange 3½" 150 lb RF, ANSI B16.5/ECTFE4)
D24
D25
D26
Flange 4" 150 lb RF, ANSI B16.5/316L
Flange 4" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 4" 150 lb RF, ANSI B16.5/ECTFE4)
D27
D28
D30
Flange 4" 150 lb RF, ANSI B16.5/PFA4)
Flange 4" 150 lb RF, ANSI B16.5/Enamelled3)
Flange 4" 150 lb LT, ANSI B16.5/316L
D31
D32
D33
Flange 4" 300 lb RF, ANSI B16.5/316L
Flange 4" 300 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 4" 300 lb RF, ANSI B16.5/ECTFE4)
D34
D35
D36
Flange 4" 300 lb RJF, ANSI B16.5/316L
Flange 4" 300 lb LG, ANSI B16.5/316L
Flange 4" 300 lb LT, ANSI B16.5/316L
D37
D38
D40
Flange 4" 600 lb RF, ANSI B16.5/316L
Flange 4" 600 lb RJF, ANSI B16.5/316L
Flange 5" 150 lb RF, ANSI B16.5/316L
D41
D42
D43
Flange 6" 150 lb RF, ANSI B16.5/316L
Flange 6" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
Flange 6" 150 lb RF, ANSI B16.5/ECTFE4)
D44
D45
D46
Flange 6" 150 lb RF, ANSI B16.5/PFA4)
Flange 6" 150 lb RJF, ANSI B16.5/316L
Flange 6" 300 lb RF, ANSI B16.5/316L
D47
D48
D50
C23
C26
C33
C36
C40
B16.5/ECTFE4)
Flange 1" 150 lb RF, ANSI
Flange 1"150 lb RF, ANSI B16.5/PFA4)
Flange 1" 150 lb RF, ANSI B16.5/Enamelled3)
C51
C52
C53
Flange 1" 300 lb RF, ANSI B16.5/316L
Flange 1" 300 lb RF, ANSI B16.5/ECTFE4)
C54
C55
Flange 1" 600 lb RF, ANSI B16.5/316L
C56
Flange 1½" 150 lb RF, ANSI B16.5/316L
Flange 1½" 150 lb RF, ANSI B16.5/
Alloy C22 (2.4602)
Flange 1½" 150 lb RF, ANSI B16.5/ECTFE4)
C57
C58
Flange 1½" 150 lb RF, ANSI B16.5/PFA4)
Flange 1½" 150 lb RF, ANSI B16.5 Enamelled3)
Flange 1½" 150 lb FF, ANSI B16.5/ECTFE4)
C61
C62
C63
Flange 1½" 300 lb RF, ANSI B16.5/316L
Flange 1½" 300 lb RF, ANSI B16.5/
Alloy 400 (2.4360) ZB2977
Flange 1½" 300 lb RF, ANSI B16.5/ECTFE4)
C64
C65
Flange 1½" 600 lb RF, ANSI B16.5/316L
Flange 2" 150 lb RF, ANSI B16.5/316L
Flange 2" 150 lb RF, ANSI B16.5/Alloy C22 (2.4602)
C67
C68
C70
Flange 2" 150 lb RF, ANSI B16.5/
Alloy 400 (2.4360) ZB2977
Flange 2" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 2" 150 lb RF, ANSI B16.5/PFA4)
C71
Flange 2" 150 lb RF, ANSI B16.5/Enamelled3)
Flange 2" 150 lb FF, ANSI B16.5/316L
C74
C75
4/96
Siemens FI 01 · Update 05/2016
7 7 7 77 - 77 7 7
C60
C66
C72
C73
C78
C80
C88
D00
D02
D03
D12
D13
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
SITRANS LVL200, Rigid extension
Compact vibrating level switch for material detection in liquid applications such as overflow, high,
low, and demand applications, as well as pump
protection. For use in SIL-2 and hazardous applications.
7ML5747-
Flange 8" 150 lb RF, ANSI B16.5/316L
Flange 8" 150 lb RF, ANSI B16.5/ECTFE4)
Flange 1" BS.10 Table E/316L
E/PFA4)
77 7 77 - 77 77
Rigid Extension 316L Ra  0.8 μm
D51
D52
D53
Flange 1" BS.10 Table
Flange 1½" BS.10 Table E/316L
Flange 3½" BS.10 Table E/316L
D54
D55
D56
Flange 4" BS.10 Table E/ECTFE4)
Flange DN 40 10K, JIS/316L
Flange DN 50 10K, JIS/316L
D57
D58
D60
Flange DN 80 10K, JIS/316L
Flange DN 100 10K, JIS/316L
Thread R1 PN64, EN10226-1/316L16)
D61
D62
D65
7 7 7 77 - 77 7 7
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
D0
D1
D2
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
D3
D4
D5
3 001 ... 3 500 mm
3 501 ... 4 000 mm
D6
D7
Rigid Extension 316L Ra  0.3 μm
Adapter/Process temperature
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
E0
E1
E2
Without adapter/-50 ... +150 °C
With adapter/-50 ... +200 °C
With adapter/-50 ... +250 °C
1
2
3
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
E3
E4
E5
With gas-tight leadthrough/-50 ... +150 °C
With gas-tight leadthrough/-50 ... +250 °C
4
5
3 001 ... 3 500 mm
3 501 ... 4 000 mm
E6
E7
Housing/Cable entry
Aluminum IP66/IP67/M20 x 1.5
Aluminum IP66/IP67/½" NPT
316L stainless steel (electropolished)
IP66/IP67/M20 x 1.510)
316L stainless steel (electropolished)
IP66/IP67/½" NPT10)
Aluminum IP66/IP67/M20 x 1.5 Special HARTING
plug (bent) according to Tier One (ZB7555)
Rigid Extension Enamelled version
A
B
C
80 ... 250 mm
251 ... 500 mm
501 ... 750 mm
F0
F1
F2
D
751 ... 1 000 mm
1 001 ... 1 250 mm
1 251 ... 1 500 mm
F3
F4
F5
V
Rigid Extension Alloy C22 (2.4602)
NOTE:
When selecting a Rigid Extension option,
extension coating must match the process
connection coating and the material and
surface roughness type.
Rigid Extension 316L
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
A0
A1
A2
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
A3
A4
A5
3 001 ... 3 500 mm
3 501 ... 4 000 mm
A6
A7
Rigid Extension ECTFE coated
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
B0
B1
B2
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
B3
B4
B5
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
G0
G1
G2
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
G3
G4
G5
3 001 ... 3 500 mm
3 501 ... 4 000 mm
G6
G7
Rigid Extension Alloy 400 (2.4360)
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
H0
H1
H2
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
H3
H4
H5
Rigid Extension PFA coated
80 ... 500 mm
501 ... 1 000 mm
1 001 ... 1 500 mm
C0
C1
C2
1 501 ... 2 000 mm
2 001 ... 2 500 mm
2 501 ... 3 000 mm
3 001 ... 3 500 mm
3 501 ... 4 000 mm
C3
C4
C5
C6
C7
Siemens FI 01 · Update 05/2016
4/97
4
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
Order code
Selection and Ordering data
4
Selection and Ordering data
Article No.
Further designs
Spare Parts and Accessories
Please add "-Z" to Article No. and specify Order
code(s).
Electronics module SITRANS LVL200 Relay
Electronics module SITRANS LVL200 Contactless
7ML1830-1NC
7ML1930-6AA
Cleaning including Certificate
(oil, grease, and silicone free)
W01
NAMUR spare electronics module
Lock fitting, unpressurized, G1" A/316L
A5E35817107
7ML1930-1DQ
Enter the total insertion length in plain text
description, max. 4 000 mm (157.48 inch)
Y01
Identification label (measurement loop) stainless
steel: max. 40 characters, add in plain text.
To add more than one line, use a coma “,” for line
break.
Y17
Lock fitting, unpressurized, 1" NPT/316L
Lock fitting, unpressurized, G1 ...1/2" A/316L
Lock fitting, unpressurized, 1 ... 1/2" NPT/316L
7ML1930-1DR
7ML1930-1DS
7ML1930-1DT
Identification Label (measurement loop) foil:
max. 40 characters add in plain text.
To add more than one line, use a coma “,” for line
break.
Y18
Lock fitting, -1 ... 16 bar, G1" A/316L
Lock fitting, -1 ... 16 bar, 1" NPT/316L
Lock fitting, -1 ... 16 bar, G1 ... 1/2" A/316L
7ML1930-1DU
7ML1930-1DV
7ML1930-1DW
Lock fitting, -1 ... 16 bar, 1 ... 1/2" NPT/316L
Lock fitting, -1 ... 64 bar, G1" A/316L
Lock fitting, -1 ... 64 bar, 1" NPT/316L
7ML1930-1DX
7ML1930-1EA
7ML1930-1EB
3.1-Inspection Certificate for material
(EN 10204 NACE MR 0175)12)
D07
Lock fitting, -1 ... 64 bar, G1 ... 1/2" A/316L
Lock fitting, -1 ... 64 bar, 1 ... 1/2" NPT/316L
7ML1930-1EC
7ML1930-1ED
2.2-Factory certificate for material (EN
10204)12)
C15
Functional Safety (SIL 2). Device suitable for use in
accordance with IEC 61508 and IEC 6151112)
C20
certificate/instrument12)
C13
Dye penetration test + 3.1
C14
Positive material identification test
+ 3.1 certificate/instrument12)
C16
Roughness test + 3.1 certificate/instrument12)
C18
3.1-Inspection Certificate for instrument (EN 10204)
C12
3.1-Inspection Certificate for instrument with test
data (EN 10204)
C25
Quality and test plan
C26
Helium leak test + 3.1
certificate/instrument12)
C31
C32
Ferrite measuring accuracy to DIN32514-1
+ 3.1 certificate/instrument12)
C60
Pressure test according to Norsok
+ 3.1 certificate/instrument12)
C61
Operating Instructions
Article No.
LVL200 Extended (DPDT Relay)
• English
7ML1998-5KW01
• German
7ML1998-5KW31
LVL200 (Contactless electronic switch)
• English
7ML1998-5KV01
• German
7ML1998-5KV31
Electronics module LVL200 Relay
• English
7ML1998-5LS01
• German
7ML1998-5LS31
Note: The Operating Instructions should be
ordered as a separate line item on the order.
All literature is available to download for free, in a
range of languages, at http://www.siemens.com/
processinstrumentation/documentation
This device is shipped with the Siemens Level and
Weighing manual DVD containing the Operating
Instructions library.
4/98
Siemens FI 01 · Update 05/2016
Available with Adapter/Process temperature options 1, 3, 4, and 5 only
Only available with housing option B
3)
Available with adapter/Process temperature options 1, 2, and 4
4)
Not in combination with adapter/Process temperature options 2, 3, and 5
5) Not in combination with adapter/Process temperature options 2, 4, and 5
8)
Only available with Electronics options 4 and 5
9)
Only valid with Rigid extension options less than 2 956 mm
10) Only available with approval options A, B, and C
Note: when selecting a Rigid option, extension coating must match the
process connection coating type.
11)
Not in combination with Rigid Extension options ECTFE Coated
Probes B0 ... B5
12) Listed Certificates are not available with all configurations please contact
factory for more information
13) Not available with Electric options 0, 1, 3, 4, 5, 6, and Housing/Protection/
Cable option V
14)
Available with Housing/Protection/Cable option V
15)
Approval option P is not available with PFA and ECTFE coating options
16) Only available for 316L extensions
2)
X-ray test + 3.1 certificate/instrument12)
Pressure test + 3.1 certificate/instrument12)
1)
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
■ Options
LVL200 threaded welded socket
Lock fitting
G1" A/316L
G¾" A/316L
LVL200 extended
16 bar
LVL200 extended
unpressurized
39 (1.54)
G1"
32
(1.26)
29.5
(1.16)
32 (1.26)
G¾"
LVL200 extended
64 bar
53 (2.09)
60 (2.36)
4
SITRANS LVL200 welded socket and lock fitting, dimensions in mm (inch)
Siemens FI 01 · Update 05/2016
4/99
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
■ Characteristic curves
Ambient temperature in °C (°F)
Ambient/Process temperature
Temperature range with
temperature adapter
70 ºC
(158 ºF)
40 ºC
(104 ºF)
-50 ºC
(-58 ºF)
4
0 ºC
(32 ºF) 0 ºC
(32 ºF)
50 ºC
(122 ºF)
100 ºC
(212 ºF)
150 ºC
(302 ºF)
-40 ºC
(-40 ºF)
200 ºC
(392 ºF)
250 ºC
(482 ºF)
Process temperature in °C (°F)
Process pressure in bar (psi g)
Process pressure with switch position 0.7 g/cm³ (mode switch)
-50 ºC
(-58 ºF)
64
(928)
40
(580)
20
(290)
-1
(-14.5)
0 ºC
(32 ºF)
50 ºC
(122 ºF)
100 ºC
(212 ºF)
150 ºC
(302 ºF)
200 ºC
(392 ºF)
250 ºC
(482 ºF)
Process temperature in °C (°F)
Process pressure in bar (psi g)
Process pressure with switch position 0.5 g/cm³ (mode switch)
-50 ºC
(-58 ºF)
64
(928)
40
(580)
20
(290)
-1
(-14.5)
0 ºC
(32 ºF)
50 ºC
(122 ºF)
100 ºC
(212 ºF)
150 ºC
(302 ºF)
200 ºC
(392 ºF)
250 ºC
(482 ºF)
Process temperature in °C (°F)
SITRANS LVL200 process pressure/process temperature/ambient temperature derating curves
4/100
Siemens FI 01 · Update 05/2016
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
■ Dimensional drawings
SITRANS LVL200 (Standard)
Stainless Steel enclosure
~ 59
(2.32 )
Ø 80
(3.15)
Aluminium enclosure
~116 (4.57)
Ø84 (3.31)
112
(4.41)
125 (4.92)
M20 x 1.5
M20 x 1.5 or
½" NPT
M20 x 1,5 or
½" NPT
Tri-clamp
57
(2.24)
Flange
Gas-tight leadthrough
34
(1.34)
Ø33.7 (1.33)
53
(2.09)
53
(2.09)
50
(1.97)
19
(0.75)
Bolting DN 40
Temperature adapter
178 (7.01)
G ¾" A, ¾" NPT
G 1" A, 1" NPT
Cone DN 25
55
(2.17)
SW 32
(G ¾" A, ¾" NPT)
SW 41
(G 1" A, 1" NPT)
36
53 (2.09) (1.42)
66
(2.60)
18.5
(0.73)
Threaded
SITRANS LVL200 (standard), dimensions in mm (inch)
Siemens FI 01 · Update 05/2016
4/101
4
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
SITRANS LVL200 (Extended)
Sensor length (L)
Stainless Steel Enclosure
~ 59
(2.32)
Aluminium Enclosure
~ 116
(4.57)
Ø 80
(3.15)
Ø 84
(3.31)
316L, Alloy C22 (2.4602)
80 ... 6 000 mm (3.15 ... 236.2 inch)
Enamelled
80 ... 1 500 mm (3.15 ... 59.06 inch)
316L, ECTFE coated
80 ... 3 000 mm (3.15 ... 118.1 inch)
316L, PFA coated
80 ... 4 000 mm (3.15 ... 157.5 inch)
112
(4.41)
M20 x 1.5
125
(4.92)
M20 x 1.5 or
½" NPT
M20 x 1.5 or
½" NPT
Threaded
Tri-clamp
Cone DN 25
4
SW 32 (G ¾" A, ¾" NPT)
SW 41 (G 1" A, 1" NPT)
18.5
(0.73)
57
(2.24)
36
(1.42)
G ¾" A, ¾" NPT
G 1" A, 1" NPT
L
L
Bolting DN 40
Temperature adapter
L
Flanged
Gas-tight leadthrough
178
(7.01)
19
(0.75)
50
(1.97)
34
(1.34)
L
L
SITRANS LVL200 (extended), dimensions in mm (inch)
4/102
Siemens FI 01 · Update 05/2016
© Siemens AG 2016
Level Measurement
Point level measurement - Vibrating switches
SITRANS LVL200
■ Schematics
Relay (DPDT)
+ –
L1 N
1
2
20 ... 72 V DC
20 ... 253 V AC
3
1
1
Control lamp
2
DIL switch for characteristics reversal
3
DIL switch for sensitivity adjustment
4
Ground terminal
5
Connection terminals
2
3
4
5
6
7
8
5
4
Relay
output
Relay
output
Voltage
supply
4
Contactless
1 2
20 ... 253V AC/DC
I max 400 mA
L N
1
1 2
1
L
N
A
≥0.5g/cm³
B
≥0.7g/cm³
1
2
3
2
1
Control lamp
2
DIL switch for mode adjustment
3
DIL switch for switching point adaptation
4
Ground terminal
5
Connection terminals
2
4
5
L1 N
AC + –
DC – +
Voltage
supply
NAMUR
N
NAMUR
(IEC 60947-5-6)
+ Simul.
6
1
max.
2
3
min.
5
1 2
4
1
Control lamp
2
DIL switch for characteristics reversal
3
DIL switch for sensitivity adjustment
4
Ground terminal
5
Simulation key
6
Connection terminals
1
Control lamp
+
–
1
2
+
–
Amplifier according to NAMUR
IEC 60947-5-6, approx. 8.2 V
Transistor (NPN/PNP)
PNP action
NPN action
SW E60T
1 2 3 4 PNP
1 2 3 4 NPN
+
+
10 ... 55 V DC
+
I
max. 400 mA
2
Out
A
B
1 2
1
2
DIL switch for mode adjustment
3
DIL switch for switching point
4
Ground terminal
5
Connection terminals
≥ 0.5 g/cm ³
≥ 0.7 g/cm ³
3
3 4
5
4
+
-
1
2 3 4
+
-
+
-
1 2 3 4
+
-
SITRANS LVL200 connections
Siemens FI 01 · Update 05/2016
4/103