ELECTRONICS Transient Voltage Suppressors 5KP Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - 5KP Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR =0.1%xVBR@25°C x ΔT BI 5. Glass passivated Chip junction in P800 package 6. 5000W peak pulse capadility at 10x1000μs waveform,repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 5μA above 11V BI Cathode 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, Anode \(9.5mm) lead length, 5lbs., (2.3kg)tension 12. Plastic package has underwriters laboratory UNI flammability classification 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units PPPM 5000 Watts PD 8 Watts IFSM 400 Amps VF 3.5/5.0 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 175°C °C Typical Thermal Resistance Junction to Lead RuJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RuJA 40 °C/W Peak Pulse Power Dissipation by 10x1000μs test waveform (Fig.1)(Note 1) Steady State Power Dissipation on inifinite heat sink at TL=75°C (Fig. 5) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional only (Note 2) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 3) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. 3. VF<3.5V for devices of VBR _< 200V and VF<5.0V for devices of VBR _> 201V. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Electriacl Characteristics Type Number (UNI) 5KP5.0A 5KP6.0A 5KP6.5A 5KP7.0A 5KP7.5A 5KP8.0A 5KP8.5A 5KP9.0A 5KP10A 5KP11A 5KP12A 5KP13A 5KP14A 5KP15A 5KP16A 5KP17A 5KP18A 5KP20A 5KP22A 5KP24A 5KP26A 5KP28A 5KP30A 5KP33A 5KP36A 5KP40A 5KP43A 5KP45A 5KP48A 5KP51A 5KP54A 5KP58A 5KP60A 5KP64A 5KP70A 5KP75A 5KP78A 5KP85A 5KP90A 5KP100A 5KP110A 5KP120A 5KP130A 5KP150A 5KP160A 5KP170A 5KP180A 5KP190A (BI) 5KP5.0CA 5KP6.0CA 5KP6.5CA 5KP7.0CA 5KP7.5CA 5KP8.0CA 5KP8.5CA 5KP9.0CA 5KP10CA 5KP11CA 5KP12CA 5KP13CA 5KP14CA 5KP15CA 5KP16CA 5KP17CA 5KP18CA 5KP20CA 5KP22CA 5KP24CA 5KP26CA 5KP28CA 5KP30CA 5KP33CA 5KP36CA 5KP40CA 5KP43CA 5KP45CA 5KP48CA 5KP51CA 5KP54CA 5KP58CA 5KP60CA 5KP64CA 5KP70CA 5KP75CA 5KP78CA 5KP85CA 5KP90CA 5KP100CA 5KP110CA 5KP120CA 5KP130CA 5KP150CA 5KP160CA 5KP170CA 5KP180CA 5KP190CA Reverse StandOff Voltage VRWM(V) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 190.0 Breakdown Voltage @IT VBR MIN.(V) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.00 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 200.00 211.00 VBR MAX.(V) 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 221.00 233.00 Test Current IT(mA) 50 50 50 50 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Maximum Clamping Voltage @IPP VC(V) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 73.5 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 292.0 310.0 Peak Pulse Current IPP(A) 554.3 495.1 445.4 425.0 395.3 375.0 354.2 331.2 300.0 280.2 256.3 237.2 219.8 209.0 196.2 184.8 174.7 157.4 143.7 131.1 121.1 112.3 105.4 95.7 87.8 79.1 73.5 70.2 65.9 61.9 58.6 54.5 52.7 49.5 45.1 42.1 40.5 37.2 34.9 31.5 28.8 26.4 24.4 21.0 19.7 18.5 17.5 16.5 Reverse Leakage @VRWM IR(µA) 5000 5000 2000 1000 250 150 50 20 15 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - 5KP Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Curve 100 Figure 2 - Pulse Derating Curve 100 Non-repetitive pulse Peak Pulse Power (kW) PPPM - Peak Pulse Power (kW) waveform shown in Fig.3 TA=25ºC 10 1 0.1 0.1µs 75 50 25 0 1.0µs 10µs 100µs 1.0ms 10ms 0 25 td - Pulse Width (sec.) Figure 3 - Pulse Waveform 100 125 150 175 200 100000 Bi-directional V=0V t r =10µsec TJ =25°C 100 10000 as the point where the peak current decays to 5 0% of I PPM Peak Value IPPM Uni-directional V=0V Uni-directional @ VR Cj (pF) IPPM- Peak Pulse Current, % I RSM 75 Figure 4 - Typical Junction Capacitance 150 Half Value IPPM IPPM ( ) 1000 100 2 50 Bi-directional @ VR 10/1000µsec. Waveform 10 td 0 1.0 0 2.0 3.0 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 4.0 10.0 450 8 400 IFSM, Peak Forward Surge Current (A) 9 7 6 5 4 L = 0.375” (9.5mm) Lead Lengths 2 1 0 0 25 50 75 100 125 150 TL - Lead Temperature(ºC) Circuit Protection System 175 1000.0 Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Figure 5 - Steady State Power Derating Curve 3 100.0 VBR - Reverse Breakdown Voltage (V) t-Time (ms) Steady State Power Dissipation (W) 50 TA - Ambient Temperature (ºC) 200 350 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - 5KP Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Critical Z P TL to T Ramp-up Temperature (T) TL tL Ts(max) Ramp-down Ts(min) ts Preheat Time (t) Weight 0.045oz., 1.2g Case JEDEC DO-201 molded plastic body over passivated junction. Polarity Color band denotes the cathode except Bipolar. Termina Matte Tin axial leads, solderable per JESD22-B102D. Environmental Specifications Flow/Wave Soldering Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 Peak Temperature : 265°C High Temp. Storage JESD22-A103 Dipping Time : 10 seconds HTRB JESD22-A108 Soldering : 1 time Thermal Shock JESD22-A106 Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - 5KP Series Dimensions Unit:mm D Inches DIM C A A B P600 Millimeters Min Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 Part Numbering System 5KPxxx XX X OPTION CODE: BLANK Reel Tape -B Bulk Packaging TYPE CODE: A Uni-Directional (5% VoltageTolerance) CA Bi-Directional VOLTAGE CODE (Refer to the Electrical Characteristics table) SERIES CODE Packaging Part Number Component Package Quantity Packaging Option Packaging Specification 5KPxxxXX P600 400 Tape & Reel ELA STD RS-296E 5KPxxxXX-B P600 100 BULK Concord Packing Spec Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6