MIC5326 DATA SHEET (11/05/2015) DOWNLOAD

MIC5326
150mA Low Operating Current LDO
General Description
Features
The MIC5326 is a low quiescent current, low dropout
regulator designed for optimal performance in a small
space. The MIC5326 is capable of sourcing 150mA of
output current while only consuming 24µA of operating
current. This high performance LDO offers low dropout,
fast transient response, good PSRR, and low output
voltage noise.
The MIC5326 is an ideal solution for battery operated
applications due to low operating current of 24μA and
extremely low dropout voltage of 85mV at 150mA.
Equipped with a TTL logic compatible enable pin, the
MIC5326 can be put into a zero-off-mode current state
drawing virtually no current when disabled.
Board space and component cost is minimized because
the MIC5326 operates with very small 1μF ceramic
capacitors, provides fixed output voltages, and is available
in the tiny 1.2mm x 1.6mm Thin MLF® package.
MIC5326 also features thermal shutdown and current limit
protection.
Data sheets and support documentation can be found on
Micrel’s web site at www.micrel.com.
•
•
•
•
•
•
•
•
150mA output current
Input voltage range: 2.3V to 5.5V
Low 24µA operating current
Low dropout voltage of 85mV @ 150mA
Fixed output voltage
Stable with 1μF ceramic capacitors
Thermal shutdown and current limit protection
Tiny 4-pin 1.2mm x 1.6mm Thin MLF® package
Applications
•
•
•
•
•
•
Mobile handsets
GPS and navigation devices
Portable media players
Digital still and video cameras
PDAs
Portable electronics
___________________________________________________________________________________________________________
Typical Application
MIC5326-xxYMT
VIN
VBAT
1µF
VOUT
VOUT
1µF
VEN
GND
LDO Application
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 9440800 • fax + 1 (408) 4741000 • http://www.micrel.com
October 2008
M9999-100808-A
Micrel, Inc.
MIC5326
Ordering Information
Part Number
Marking(2)
Voltage(1)
Temperature Range
Package(3)
MIC5326-2.8YMT
2Q8
2.8V
–40° to +125°C
4-Pin 1.2mm x 1.6mm Thin MLF®
Note:
1.
For other voltage options contact Micrel Marketing.
2.
Pin 1 identifier= “▲”.
3.
MLF is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
Pin Configuration
VIN 1
4
VOUT
GND 2
3
EN
4-Pin 1.2mm x 1.6mm Thin MLF® (MT)
Pin Description
Pin Number
Pin Name
Pin Function
1
VIN
Supply Input.
2
GND
Ground.
3
EN
4
VOUT
Output Voltage.
HSPAD
EPAD
Exposed heatsink pad connected to ground internally.
October 2008
Enable Input: Active High Logic Input. Logic High = On; Logic Low = Off. Do
not leave floating.
2
M9999-100808-A
Micrel, Inc.
MIC5326
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN) ........................................ –0.3V to +6V
Enable Voltage (VEN)......................................... –0.3V to VIN
Power Dissipation (PD) ........................... Internally Limited(3)
Lead Temperature ( soldering, 5sec.)........................ 260°C
Junction Temperature(TJ ).........................–40°C to +125°C
Storage Temperature (Ts) .........................–65°C to +150°C
ESD Rating..................................................................... 2kV
Supply Voltage (VIN)......................................... 2.3V to 5.5V
Enable/Select Voltage (VEN)................................... 0V to VIN
Junction Temperature (TJ) ........................ –40°C to +125°C
Junction Thermal Resistance
1.2mm x 1.6mm Thin MLF-4 (θJA)......................173°C/W
Electrical Characteristics(5)
VIN = VEN = VOUT + 1V; COUT = 1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C to +125°C, unless noted.
Parameter
Condition
Min
Output Voltage Accuracy
Variation from nominal VOUT
–1.5
Variation from nominal VOUT
–2.0
Line Regulation
VIN = VOUT +1V to 5.5V, IOUT = 100µA
Typ
0.01
VIN = VOUT +1V to 5.5V, IOUT = 100µA
(6)
0.05
Max
Units
+1.5
%
+2.0
%
0.3
%/V
0.5
%/V
Load Regulation
IOUT = 100µA to 150mA
Dropout Voltage(7)
IOUT = 50mA
30
mV
IOUT = 100mA
55
mV
1
%
IOUT = 150mA
85
150
mV
Ground Pin Current(8)
IOUT = 100µA to 150mA
24
35
µA
Ground Pin Current in Shutdown
VEN = 0V
0.01
1
µA
Ripple Rejection
f = 1kHz; COUT = 1µF; IOUT = 150mA
60
dB
f = 20kHz; COUT = 1µF; IOUT = 150mA
50
dB
Current Limit
VOUT = 0V
Output Voltage Noise
COUT = 1µF, 10Hz to 100kHz
275
475
750
90
mA
µVRMS
Enable Voltage
Enable Voltage
Logic Low
0.2
Logic High
Enable Current
Turn on Time
V
V
1.2
VIL ≤ 0.2V
0.01
1
µA
VIH ≥ 1.2V
0.01
1
µA
COUT = 1µF; IOUT = 150mA
150
500
µs
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any TA (ambient temperature) is PD(max) = (TJ(max) – TA) / θJA. Exceeding the maximum allowable power
dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
5. Specification for packaged product only.
6. Regulation is measured at constant junction temperature using low duty cycle pulse testing.
7. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal VOUT
8. Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin
current.
October 2008
3
M9999-100808-A
Micrel, Inc.
MIC5326
Typical Characteristics
Power Supply
Rejection Ratio
3.00
50mA
100mA
150mA
VIN = VOUT +1V
0 VOUT = 2.8V
COUT = 1µF
10
10
100
1k
10k 100k
FREQUENCY (Hz)
2.95
2.90
2.90
2.85
2.85
2.80
2.80
2.75
2.75
2.70
VIN = VEN = VOUT +1
VOUT = 2.8V
CIN = COUT = 1µF
2.65
1M
Output Voltage
vs. Input Voltage
2.60
0
25 50 75 100 125 150
OUTPUT CURRENT (mA)
Ground Current
vs. Output Current
32
24
50mA
2.5
120
3.0 3.5 4.0 4.5 5.0
INPUT VOLTAGE (V)
5.5
Dropout Voltage
vs. Temperature
2.60
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
Dropout Voltage
vs. Output Current
60
50
100µA
2.0
2.5
VIN = VEN = VOUT +1V
CIN = COUT = 1µF
2.65
90
80
70
28
VEN = 1.2V
VOUT = 2.8V
CIN = COUT = 1µF
2.70
100
3.0
150mA
Output Voltage
vs. Temperature
3.00
2.95
100µA
3.5
Output Voltage
vs. Output Current
20
VIN = VEN = VOUT + 1
VOUT = 2.8V
CIN = COUT = 1µF
16
0
25 50 75 100 125 150
OUTPUT CURRENT (mA)
Ground Current
vs. Temperature
32
40
30
20
10
0
0
34
100
VEN = VIN
CIN = COUT = 1µF
25 50 75 100 125 150
OUTPUT CURRENT (mA)
Ground Current
vs. Input Voltage
30
150mA
28
80
26
60
100µA
24
40
VEN = 1.2V
VOUT = 2.8V
CIN = COUT = 1µF
ILOAD = 150mA
20
22 100µA
150mA
VIN = VEN = VOUT + 1V
VOUT = 2.8V
CIN = COUT = 1µF
20
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
16
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
Current Limit
vs. Input Voltage
Output Noise
Spectral Density
700
VEN = 1.2V
VOUT = 2.8V
CIN = COUT = 1µF
650
100
10
18
VIN = VEN
VOUT = 2.8V
CIN = COUT = 1µF
14
10
2.5
3
3.5
4
4.5
5
INPUT VOLTAGE (V)
5.5
VIN = 4.5V
VOUT = 2.8V
COUT = 1µF
600
550
1
500
0.1
450
400
2.5
3.0 3.5 4.0 4.5 5.0
INPUT VOLTAGE (V)
October 2008
5.5
0.01
100
1k
10k
100k
FREQUENCY (Hz)
4
1M
M9999-100808-A
Micrel, Inc.
MIC5326
Functional Characteristics
October 2008
5
M9999-100808-A
Micrel, Inc.
MIC5326
Functional Diagram
VIN
VOUT
LDO
EN
REFERENCE
GND
MIC5326 Block Diagram
October 2008
6
M9999-100808-A
Micrel, Inc.
MIC5326
Thermal Considerations
The MIC5326 is designed to provide 150mA continuous
output current from a very small footprint package.
Maximum ambient operating temperature can be
calculated based on the output current and the voltage
drop across the part. For example: given that the input
voltage is 3.6V, the output voltage is 2.8V and the output
current is 150mA. The power dissipation of the regulator
circuit can be determined using the equation:
Applications Information
The MIC5326 is a low quiescent current, low dropout
regulator designed for optimal performance in a small
space. The MIC5326 regulator is fully protected from
damage due to fault conditions, offering linear current
limiting and thermal shutdown.
Input Supply Voltage
VIN provides the supply to power the LDO. The minimum
input voltage is 2.3V allowing conversion from typical
lithium ion batteries and low voltage supplies.
PD = (VIN – VOUT) I OUT + VIN IGND
Because this device is CMOS and the ground current is
typically <100µA over the load range, the power
dissipation contributed by the ground current is < 1%
and can be ignored for this calculation.
Input Capacitor
The MIC5326 is a high performance, high bandwidth
device; therefore it requires a well bypassed input supply
for optimal performance. A 1µF capacitor is required
from the input to ground to provide stability. Low ESR
ceramic capacitors provide optimal performance with
minimum space required. Additional high frequency
capacitors, such as small value NPO dielectric type
capacitors, help filter out high frequency noise and are
good practice in any RF circuit.
PD = (3.6V – 2.8V) × 150mA
PD = 0.12W
To determine the maximum ambient operating
temperature use the junction to ambient thermal
resistance of the device and the following basic
equation:
⎛ TJ(max) − TA
PD(max) = ⎜⎜
θ JA
⎝
Output Capacitor
The MIC5326 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized for
use with low ESR ceramic chip capacitors. High ESR
capacitors may cause high frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 1µF ceramic output capacitor.
X7R/X5R dielectric type ceramic capacitors are
recommended
because
of
their
temperature
performance. X7R type capacitors change capacitance
by 15% over their operating temperature range. Z5U and
Y5V dielectric capacitors change value by as much as
50% and 60% respectively over their operating
temperature ranges. To use a ceramic chip capacitor
with Y5V dielectric the value must be much higher than
an X7R ceramic capacitor to ensure the same minimum
capacitance over the equivalent operating temperature
range.
The maximum junction temperature of the die, TJ(max) =
125°C.The package thermal resistance, θJA = 173°C/W.
Substituting PD for PD(max) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit.
The maximum power dissipation must not be exceeded
for proper operation.
For example, when operating the MIC5326 at an input
voltage of 3.6V and 150mA load with a minimum
footprint layout, the maximum ambient operating
temperature TA can be determined as follows:
0.12W = (125°C – TA)/(173°C/W)
TA = 104.24°C
Therefore a 2.8V 150mA application can accept an
ambient operating temperature of 104.24°C in a 1.2mm
x 1.6mm Thin MLF® package. For a full discussion of
heat sinking and thermal effects on voltage regulators,
refer to the “Regulator Thermals” section of Micrel’s
Designing with Low Dropout Voltage Regulators
handbook. This information can be found on Micrel's
website at:
http://www.micrel.com/_PDF/other/LDOBk_ds.pdf
Minimum Load Current
The MIC5326 does not require a minimum load to
maintain output voltage regulation.
Enable/ Shutdown
The MIC5326 comes with an active high enable pin that
enables the regulator. Forcing the enable pin low
disables the regulator and sends it into a “zero” off mode
current state. In this state, current consumed by the
regulator goes nearly to zero. The active high enable pin
uses CMOS technology and cannot be left floating; a
floating enable pin may cause an unknown output state.
October 2008
⎞
⎟
⎟
⎠
7
M9999-100808-A
Micrel, Inc.
MIC5326
U1
MIC5326-xxYMT
J1
VIN
1
VIN
VOUT
J3
VOUT
4
C1
1µF
J5
EN
3
EN
GND
C2
1µF
2
J4
GND
J2
GND
Bill of Materials
Item
Part Number
Manufacturer
Description
Qty.
C1, C2
C1608X5R0J105K
TDK(1)
Capacitor, 1µF, 10V, X5R, Size 0603
2
150mA Low Operating Current LDO
1
U1
MIC5326-xxYMT
Micrel, Inc.
(2)
Notes:
1. TDK: www.tdk.com
2. Micrel, Inc.: www.micrel.com
October 2008
8
M9999-100808-A
Micrel, Inc.
MIC5326
PCB Layout Recommendations
Top Layer
Bottom Layer
October 2008
9
M9999-100808-A
Micrel, Inc.
MIC5326
Package Information
4-Pin 1.2mm x 1.6mm Thin MLF® (MT)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 9440800 FAX +1 (408) 4741000 WEB http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its
use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant
into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2008 Micrel, Incorporated.
October 2008
10
M9999-100808-A