CY7C601xx CY7C602xx enCoRe™ II Low Voltage Microcontroller Features • enCoRe™ II Low Voltage (enCoRe II LV)—“enhanced Component Reduction” — Internal crystalless oscillator with support for optional external clock or external crystal or resonator. — Configurable IO for real-world interface without external components • Enhanced 8-bit microcontroller • • • • Improved output drivers to reduce EMI Operating voltage from 2.7V to 3.6VDC Operating temperature from 0–70°C Available in 24/40-pin PDIP, 24-pin SOIC, 24-pin QSOP/SSOP, 28-pin SSOP and 48-pin SSOP. • Advanced development tools based on Cypress PSoC® tools • Industry-standard programmer support Applications — Harvard architecture — M8C CPU speed can be up to 12 MHz or sourced by an external crystal, resonator, or clock signal • Internal memory The CY7C601xx/CY7C602xx is targeted for the following applications: • PC Wireless HID devices — 256 bytes of RAM — Mice (optomechanical, optical, trackball) — 8 Kbytes of Flash including EEROM emulation • Low power consumption — Typically 2.25 mA at 3 MHz — 5 µA sleep • In-system reprogrammability — Keyboards — Presenter tools • Gaming — Joysticks — Gamepad • General purpose wireless applications — Allows easy firmware update • General-purpose I/O ports — Remote controls — Up to 36 General Purpose I/O (GPIO) pins — Barcode scanners — High current drive on GPIO pins. Configurable 8- or 50mA/pin current sink on designated pins — Each GPIO port supports high-impedance inputs, configurable pull-up, open drain output, CMOS/TTL inputs, and CMOS output — Maskable interrupts on all I/O pins • SPI serial communication — Master or slave operation — Configurable up to 2-Mbit/second transfers. — Supports half duplex single data line mode for optical sensors • 2-channel 8-bit or 1-channel 16-bit capture timer registers. Capture timer registers store both rising and falling edge times — Two registers each for two input pins — Separate registers for rising and falling edge capture — Simplifies interface to RF inputs for wireless applications • Internal low-power wake-up timer during suspend mode • • • • — Periodic wake-up with no external components Programmable Interval Timer interrupts Reduced RF emissions at 27 MHz and 96 MHz Watchdog timer (WDT) Low voltage detection with user-selectable threshold voltages Cypress Semiconductor Corporation Document 38-16016 Rev. *C • — POS terminal — Consumer electronics — Toys Introduction The enCoRe II LV family brings the features and benefits of the enCoRe II to non-USB applications. The enCoRe II family has an integrated oscillator that eliminates the external crystal or resonator, reducing overall cost. Other external components, such as wake-up circuitry, are also integrated into this chip. The enCoRe II LV is a low-voltage, low-cost 8-bit Flashprogrammable microcontroller The enCoRe II LV features up to 36 general-purpose I/O (GPIO) pins. The I/O pins are grouped into five ports (Port 0 to 4). The pins on Port 0 and Port 1 may each be configured individually while the pins on Ports 2, 3, and 4 may only be configured as a group. Each GPIO port supports highimpedance inputs, configurable pull up, open drain output, CMOS/TTL inputs, and CMOS output with up to five pins that support programmable drive strength of up to 50 mA sink current. Additionally, each I/O pin can be used to generate a GPIO interrupt to the microcontroller. Each GPIO port has its own GPIO interrupt vector with the exception of GPIO Port 0. GPIO Port 0 has in addition to the port interrupt vector, three dedicated pins that have independent interrupt vectors (P0.2–P0.4). 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised October 23, 2006 [+] Feedback CY7C601xx CY7C602xx The enCoRe II LV features an internal oscillator. Optionally, an external 1 MHz to 24 MHz crystal can be used to provide a higher precision reference. The enCoRe II LV also supports external clock The enCoRe II LV has 8 Kbytes of Flash for user’s code and 256 bytes of RAM for stack space and user variables. In addition, enCoRe II LV includes a Watchdog timer, a vectored interrupt controller, a 16-bit Free-Running Timer with Capture registers and a 12-bit Programmable Interval Timer. The Power-on reset circuit detects when power is applied to the device, resets the logic to a known state, and begins executing instructions at Flash address 0x0000. When power falls below a programmable trip voltage it generates a reset or may be configured to generate an interrupt. There is a Lowvoltage detect circuit that detects when VCC drops below a programmable trip voltage and it may be configurable to generate a LVD interrupt to inform the processor about the low-voltage event. POR and LVD share the same interrupt; there is no separate interrupt for each. The Watchdog timer can be used to ensure the firmware never gets stalled in an infinite loop. The microcontroller supports 17 maskable interrupts in the vectored interrupt controller. All interrupts can be masked. Interrupt sources include LVR/POR, a programmable interval timer, a nominal 1.024-ms programmable output from the Free Running Timer, two capture timers, five GPIO Ports, three GPIO pins, two SPI, a 16-bit free-running timer wrap and an internal wakeup timer interrupt. The wakeup timer causes periodic interrupts when enabled. The capture timers interrupt whenever a new timer value is saved due to a selected GPIO edge event. A total of eight GPIO interrupts support both TTL or CMOS thresholds. For additional flexibility, on the edgesensitive GPIO pins, the interrupt polarity is programmable to be either rising or falling. The free-running timer generates an interrupt at 1024-µs rate. It can also generate an interrupt when the free-running counter overflow occurs—every 16.384 ms. The timer can be used to measure the duration of an event under firmware control by reading the timer at the start and at the end of an event, then calculating the difference between the two values. The two 8bit capture timer registers save a programmable 8-bit range of the free-running timer when a GPIO edge occurs on the two capture pins (P0.5, P0.6). The two 8-bit capture registers can be ganged into a single 16-bit capture register. The enCoRe II LV supports in-system programming by using the P1.0 and P1.1 pins as the serial programming mode interface. Conventions In this document, bit positions in the registers are shaded to indicate which members of the enCoRe II LV family implement the bits. Available in all enCoRe II LV family members CY7C601xx only Logic Block Diagram Figure 1. CY7C601xx/CY7C602xx Block Diagram Interrupt Control 4 SPI/GPIO Pins 16 Extended I/O Pins 16 GPIO Pins Wakeup Timer Internal 12 MHz Oscillator M8C CPU Clock Control POR / Low-Voltage Detect Flash 8K Byte 12-bit Timer Capture Timers Watchdog Timer Vdd Crystal Oscillator CY7C601xx only RAM 256 Byte Document 38-16016 Rev. *C Page 2 of 62 [+] Feedback CY7C601xx CY7C602xx Packages/Pinouts Figure 2. Package Configurations Top View CY7C60223 24-pin PDIP P3.0 P3.1 SCLK/P1.4 SMOSI/P1.5 SMISO/P1.6 P1.7 NC NC P0.7 TIO1/P0.6 TIO0/P0.5 INT2/P0.4 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 P1.3/SSEL P1.2 VDD P1.1 P1.0 VSS P2.0 P2.1 P0.0/CLKIN P0.1/CLKOUT P0.2/INT0 P0.3/INT1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 NC P0.7 TIO1/P0.6 TIO0/P0.5 INT2/P0.4 INT1/P0.3 INT0/P0.2 CLKOUT\P0.1 CLKIN\P0.0 P2.1 P2.0 VSS 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 NC P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P3.1 P3.0 P1.3/SSEL P1.2 VDD P1.1 P1.0 VSS P3.7 P3.6 P3.5 P3.4 P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P1.3/SSEL P1.2 VDD P1.1 P1.0 Document 38-16016 Rev. *C VDD P4.1 P4.0 P2.7 P2.6 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 P0.7 T1O1/P0.6 TIO0/P0.5 INT2/P0.4 INT1/P0.3 INT0/P0.2 CLKOUT/P0.1 CLKIN/P0.0 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 NC P0.7 TIO1/P0.6 TIO0/P0.5 INT2/P0.4 INT1/P0.3 INT0/P0.2 CLKOUT\P0.1 CLKIN\P0.0 P2.1 P2.0 NC 1 2 3 4 5 6 7 8 9 10 11 12 P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P3.1 P3.0 P1.3/SSEL P1.2 VDD P1.1 P1.0 VSS 24 23 22 21 20 19 18 17 16 15 14 13 CY7C60123 48-pin SSOP CY7C60123 40-pin PDIP CY7C60113 28-pin SSOP VDD P2.7 P2.6 P2.5 P2.4 P0.7 TIO1/P0.6 TIO0/P0.5 INT2/P0.4 INT1/P0.3 INT0/P0.2 CLKOUT/P0.1 CLKIN/P0.0 VSS CY7C60223 24-pin QSOP CY7C60223 24-pin SOIC VSS P4.3 P4.2 P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P1.3/SSEL P1.2 VDD P1.1 P1.0 NC NC NC NC VDD P4.1 P4.0 P2.7 P2.6 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 P0.7 TIO1/P0.6 TIO0/PO.5 INT2/P0.4 INT1/P0.3 INT0/P0.2 CLKOUT/P0.1 CLKIN/P0.0 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 NC NC NC NC VSS P4.3 P4.2 P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P1.3/SSEL P1.2 VDD P1.1 P1.0 Page 3 of 62 [+] Feedback CY7C601xx CY7C602xx Pin Assignments Table 1. Pin Assignments 48 40 28 24 24 SSOP PDIP SSOP QSOP SOIC 7 24 PDIP 3 Name P4.0 6 2 P4.1 42 38 P4.2 43 39 P4.3 34 30 19 18 1 35 31 20 19 2 36 32 37 33 38 34 24 P3.4 39 35 25 P3.5 40 36 26 P3.6 41 37 27 P3.7 P3.0 Description GPIO Port 4—configured as a group (nibble) GPIO Port 3—configured as a group (byte) P3.1 P3.2 P3.3 15 11 11 11 18 P2.0 14 10 10 10 17 P2.1 13 9 P2.2 12 8 P2.3 GPIO Port 2—configured as a group (byte) 11 7 5 P2.4 10 6 4 P2.5 9 5 3 P2.6 8 4 2 P2.7 25 21 15 14 13 20 P1.0 GPIO Port 1 bit 0 26 22 16 15 14 21 P1.1 GPIO Port 1 bit 1 28 24 18 17 16 23 P1.2 GPIO Port 1 bit 2 29 25 19 18 17 24 P1.3/SSEL GPIO Port 1 bit 3—Configured individually. Alternate function is SSEL signal of the SPI bus 30 26 20 21 20 3 P1.4/SCLK GPIO Port 1 bit 4—Configured individually. Alternate function is SCLK signal of the SPI bus 31 27 21 22 21 4 P1.5/SMOSI GPIO Port 1 bit 5—Configured individually. Alternate function is SMOSI signal of the SPI bus 32 28 22 23 22 5 P1.6/SMISO GPIO Port 1 bit 6—Configured individually. Alternate function is SMISO signal of the SPI bus 33 29 23 24 23 6 P1.7 GPIO Port 1 bit 7—Configured individually. TTL voltage threshold 23 19 13 9 9 16 P0.0/CLKIN GPIO Port 0 bit 0—Configured individually. On CY7C601xx, optional Clock In when external oscillator is disabled or external oscillator input when external oscillator is enabled. On CY7C602xx, oscillator input when configured as Clock In If this pin is used as a General Purpose output it will draw current. This pin should be configured as an input to reduce current draw. Document 38-16016 Rev. *C Page 4 of 62 [+] Feedback CY7C601xx CY7C602xx Table 1. Pin Assignments (continued) 48 40 28 24 24 SSOP PDIP SSOP QSOP SOIC 24 PDIP Name Description 22 18 12 8 8 15 P0.1/CLKOUT GPIO Port 0 bit 1—Configured individually On CY7C601xx, optional clock out when external oscillator is disabled or external oscillator output drive when external oscillator is enabled. On CY7C602xx, oscillator output when configured as Clock Out. If this pin is used as a General Purpose output it will draw current. This pin should be configured as an input to reduce current draw. 21 17 11 7 7 14 P0.2/INT0 GPIO port 0 bit 2—Configured individually Optional rising edge interrupt INT0 20 16 10 6 6 13 P0.3/INT1 GPIO port 0 bit 3—Configured individually Optional rising edge interrupt INT1 19 15 9 5 5 12 P0.4/INT2 GPIO port 0 bit 4—Configured individually Optional rising edge interrupt INT2 18 14 8 4 4 11 P0.5/TIO0 GPIO port 0 bit 5—Configured individually Alternate function Timer capture inputs or Timer output TIO0 17 13 7 3 3 10 P0.6/TIO1 GPIO port 0 bit 6—Configured individually Alternate function Timer capture inputs or Timer output TIO1 16 12 6 2 2 9 P0.7 GPIO port 0 bit 7—Configured individually 1,2,3, 4 1 1 7 NC No connect 45,46, 47,48 12 24 8 NC No connect VDD Power VSS Ground 5 1 17 27 23 1 16 15 22 44 40 14 – – – 24 20 28 13 12 19 Document 38-16016 Rev. *C Page 5 of 62 [+] Feedback CY7C601xx CY7C602xx Register Summary enCoRe II LV Register Summary Addr Name 7 6 5 4 3 2 1 0 R/W Default 00 P0DATA P0.7 P0.6/TIO1 P0.5/TIO0 P0.4/INT2 P0.3/INT1 P0.2/INT0 P0.1/ CLKOUT P0.0/CLKIN bbbbbbbb 00000000 01 P1DATA P1.7 P1.4/SCLK P1.3/SSEL P1.2 P1.1 P1.0 bbbbbbbb 00000000 02 P2DATA P2.7–P2.2 P2.1–P2.0 bbbbbbbb 00000000 03 P3DATA P3.7–P3.2 P3.1–P3.0 bbbbbbbb 00000000 04 P4DATA 05 P00CR Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable 06 P01CR CLK Output Int Enable Int Act Low TTL Thresh High Sink Open Drain 07–09 P02CR– P04CR Int Act Low TTL Thresh Reserved 0A–0B P05CR– P06CR TIO Output Int Enable Int Act Low TTL Thresh 0C P07CR Reserved Int Enable Int Act Low TTL Thresh 0D P10CR Reserved Int Enable Int Act Low 0E P11CR Reserved Int Enable Int Act Low 0F P12CR CLK Output Int Enable Int Act Low TTL Threshold 10 P13CR Reserved Int Enable Int Act Low 11–13 P14CR– P16CR SPI Use Int Enable 14 P17CR Reserved 15 P2CR 16 17 P1.6/SMISO P1.5/SMOSI Reserved Reserved P4.3–P4.0 ----bbbb 00000000 Output Enable -bbbbbbb 00000000 Pull-up Enable Output Enable bbbbbbbb 00000000 Open Drain Pull-up Enable Output Enable --bb-bbb 00000000 Reserved Open Drain Pull-up Enable Output Enable bbbb-bbb 00000000 Reserved Open Drain Pull-up Enable Output Enable -bbb-bbb 00000000 Output Enable -bb----b 00000000 Reserved Reserved Open Drain Reserved Output Enable -bb--b-b 00000000 Reserved Open Drain Pull-up Enable Output Enable bbbb-bbb 00000000 Reserved High Sink Open Drain Pull-up Enable Output Enable -bb-bbbb 00000000 Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable bbb-bbbb 00000000 Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable -bb-bbbb 00000000 Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable -bbbbbbb 00000000 P3CR Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable -bbbbbbb 00000000 P4CR Reserved Int Enable Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable -bbb-bbb 00000000 20 FRTMRL Free Running Timer [7:0] bbbbbbbb 00000000 21 FRTMRH Free Running Timer [15:8] bbbbbbbb 00000000 22 TCAP0R Capture 0 Rising [7:0] rrrrrrrr 00000000 23 TCAP1R Capture 1 Rising [7:0] rrrrrrrr 00000000 24 TCAP0F Capture 0 Falling [7:0] rrrrrrrr 00000000 25 TCAP1F Capture 1 Falling [7:0] rrrrrrrr 00000000 26 PITMRL Prog Interval Timer [7:0] rrrrrrrr 00000000 27 PITMRH 28 PIRL 29 PIRH 2A TMRCR 2B Reserved Prog Interval Timer [11:8] Prog Interval [7:0] Reserved First Edge Hold Prog Interval [11:8] 8-bit capture Prescale Cap0 16bit Enable TCAPINTE Reserved Cap1 Fall Active Cap1 Rise Active Cap0 Fall Active 2C TCAPINTS Reserved Cap1 Fall Active Cap1 Rise Active Cap0 Fall Active 30 CPUCLKCR 31 TMRCLKCR 32 CLKIOCR Reserved 34 IOSCTR foffset[2:0] TCAPCLK Divider Document 38-16016 Rev. *C TCAPCLK Select XOSC Select ITMRCLK Divider XOSC Enable EFTB Disabled Gain[4:0] 00000000 00000000 ----bbbb 00000000 bbbbb--- 00000000 Cap0 Rise Active ----bbbb 00000000 Cap0 Rise Active ----bbbb 00000000 CPU CLK Select -------b 00000000 Reserved Reserved ----rrrr bbbbbbbb ITMRCLK Select bbbbbbbb 10001111 CLKOUT Select ---bbbbb 00000000 bbbbbbbb 000ddddd Page 6 of 62 [+] Feedback CY7C601xx CY7C602xx enCoRe II LV Register Summary (continued) Addr Name 35 XOSCTR 36 LPOSCTR 3C SPIDATA 3D SPICR 7 6 5 4 3 32-kHz Low Power Reserved 32-kHz Bias Trim [1:0] Swap LSB First Comm Mode Reserved 2 XOSC XGM [2:0] 1 0 Reserved Mode 32-kHz Freq Trim [3:0] SPIData[7:0] DA INT_CLR0 GPIO Port 1 Sleep Timer INT1 GPIO Port 0 DB INT_CLR1 TCAP0 DC INT_CLR2 Reserved DE INT_MSK3 ENSWINT DF INT_MSK2 Reserved E1 INT_MSK1 TCAP0 Prog Interval 1-ms Timer Int Enable Timer Int Enable Int Enable E0 INT_MSK0 GPIO Port 1 Sleep Timer Int Enable Int Enable CPOL CPHA SPI Receive SPI Transmit Prog Interval 1-ms Timer Timer SCLK Select INT0 POR/LVD Reserved GPIO Port 4 GPIO Port 3 GPIO Port 2 Reserved GPIO Port 4 GPIO Port 3 GPIO Port 2 Int Enable Int Enable Int Enable Reserved SPI Receive Int Enable ---bbb-b 000ddddd b-bbbbbb d-dddddd bbbbbbbb 00000000 bbbbbbbb 00000000 bbbbbbbb 00000000 bbb----- 00000000 00000000 16-bit Counter Wrap TCAP1 -bbb-bbb r------- 00000000 INT2 Int Enable 16-bit Counter Wrap Int Enable TCAP1 Int Enable -bbb-bbb 00000000 bbb----- 00000000 bbbbbbbb 00000000 Reserved GPIO Port 0 Int Enable Default INT2 Reserved INT1 Int Enable R/W SPI Transmit Int Enable INT0 Int Enable POR/LVD Int Enable E2 INT_VC Pending Interrupt [7:0] bbbbbbbb 00000000 E3 RESWDT Reset Watchdog Timer [7:0] wwwwwww w 00000000 -- CPU_A Temporary Register T1 [7:0] -------- 00000000 -- CPU_X X[7:0] -------- 00000000 -- CPU_PCL Program Counter [7:0] -------- 00000000 -- CPU_PCH Program Counter [15:8] -------- 00000000 -- CPU_SP F7 CPU_F FF CPU_SCR 1E0 OSC_CR0 Stack Pointer [7:0] Reserved GIES Reserved Reserved 1E3 LVDCR Reserved 1EB ECO_TR Sleep Duty Cycle [1:0] 1E4 VLTCMP WDRS No Buzz -------- 00000000 XIO Super Carry Zero Global IE ---brbbb 00000010 PORS Sleep Reserved Reserved Stop r-ccb--b 00010100 CPU Speed [2:0] --bbbbbb 00000000 VM[2:0] --bb-bbb 00000000 bb------ 00000000 ------rr 00000000 Sleep Timer [1:0] PORLEV[1:0] Reserved Reserved Reserved Note: In the R/W column, LVD PPOR Table 2. CPU Registers and Register Name b = Both Read and Write Register Register Name r = Read Only Flags CPU_F w = Write Only Program Counter CPU_PC c = Read/Clear Accumulator CPU_A d = calibration value. Should not change during normal use Stack Pointer CPU_SP CPU Architecture Index CPU_X This family of microcontrollers is based on a high performance, 8-bit, Harvard architecture microprocessor. Five registers control the primary operation of the CPU core. These registers are affected by various instructions, but are not directly accessible through the register space by the user. The 16-bit Program Counter Register (CPU_PC) allows for direct addressing of the full eight Kbytes of program memory space. The Accumulator Register (CPU_A) is the general-purpose register that holds the results of instructions that specify any of the source addressing modes. The Index Register (CPU_X) holds an offset value that is used in the indexed addressing modes. Typically, this is used to address a block of data within the data memory space. Document 38-16016 Rev. *C Page 7 of 62 [+] Feedback CY7C601xx CY7C602xx shift operations. The manner in which each flag is changed is dependent upon the instruction being executed (i.e., AND, OR, XOR). See Table 19. The Stack Pointer Register (CPU_SP) holds the address of the current top-of-stack in the data memory space. It is affected by the PUSH, POP, LCALL, CALL, RETI, and RET instructions, which manage the software stack. It can also be affected by the SWAP and ADD instructions. CPU Registers The Flag Register (CPU_F) has three status bits: Zero Flag bit [1]; Carry Flag bit [2]; Supervisory State bit [3]. The Global Interrupt Enable bit [0] is used to globally enable or disable interrupts. The user cannot manipulate the Supervisory State status bit [3]. The flags are affected by arithmetic, logic, and Flags Register The Flags Register can only be set or reset with logical instruction. Table 3. CPU Flags Register (CPU_F) [R/W] Bit # 7 Field 6 5 Reserved 4 3 2 1 0 XIO Super Carry Zero Global IE Read/Write – – – R/W R RW RW RW Default 0 0 0 0 0 0 1 0 Bit [7:5]: Reserved Bit 4: XIO Set by the user to select between the register banks. 0 = Bank 0 1 = Bank 1 Bit 3: Super Indicates whether the CPU is executing user code or Supervisor Code. (This code cannot be accessed directly by the user.) 0 = User Code 1 = Supervisor Code Bit 2: Carry Set by CPU to indicate whether there has been a carry in the previous logical/arithmetic operation. 0 = No Carry 1 = Carry Bit 1: Zero Set by CPU to indicate whether there has been a zero result in the previous logical/arithmetic operation. 0 = Not Equal to Zero 1 = Equal to Zero Bit 0: Global IE Determines whether all interrupts are enabled or disabled. 0 = Disabled 1 = Enabled Note: This register is readable with explicit address 0xF7. The OR F, expr and AND F, expr must be used to set and clear the CPU_F bits. Accumulator Register Table 4. CPU Accumulator Register (CPU_A) Bit # 7 6 5 Field 4 3 2 1 0 CPU Accumulator [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 Bit [7:0]: CPU Accumulator [7:0] 8-bit data value holds the result of any logical/arithmetic instruction that uses a source addressing mode. Document 38-16016 Rev. *C Page 8 of 62 [+] Feedback CY7C601xx CY7C602xx Index Register Table 5. CPU X Register (CPU_X) Bit # 7 6 5 4 Field 3 2 1 0 X [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 2 1 0 Bit [7:0]: X [7:0] 8-bit data value holds an index for any instruction that uses an indexed addressing mode. Stack Pointer Register Table 6. CPU Stack Pointer Register (CPU_SP) Bit # 7 6 5 4 Field 3 Stack Pointer [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 4 3 2 1 0 Bit [7:0]: Stack Pointer [7:0] 8-bit data value holds a pointer to the current top-of-stack. CPU Program Counter High Register Table 7. CPU Program Counter High Register (CPU_PCH) Bit # 7 6 5 Field Program Counter [15:8] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 4 3 2 1 0 Bit [7:0]: Program Counter [15:8] 8-bit data value holds the higher byte of the program counter. CPU Program Counter Low Register Table 8. CPU Program Counter Low Register (CPU_PCL) Bit # 7 6 5 Field Program Counter [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 Bit [7:0]: Program Counter [7:0] 8-bit data value holds the lower byte of the program counter. Addressing Modes Source Immediate The result of an instruction using this addressing mode is placed in the A register, the F register, the SP register, or the X register, which is specified as part of the instruction opcode. Operand 1 is an immediate value that serves as a source for the instruction. Arithmetic instructions require two sources; the Document 38-16016 Rev. *C second source is the A, X, SP, or F register specified in the opcode. Instructions using this addressing mode are two bytes in length. Table 9. Source Immediate Opcode Instruction Operand 1 Immediate Value Page 9 of 62 [+] Feedback CY7C601xx CY7C602xx Examples Examples ADD A, 7 ;In this case, the immediate value of 7 is added with the Accumulator and the result is placed in the Accumulator. MOV X, 8 ;In this case, the immediate value of 8 is moved to the X register. AND F, 9 ADD A, [X+7] ;In this case, the value in the memory location at address X + 7 is added with the Accumulator, and the result is placed in the Accumulator. MOV X, REG[X+8] ;In this case, the value in the register space at address X + 8 is moved to the X register. ;In this case, the immediate value of 9 is logically ANDed with the F register and the result is placed in the F register. Destination Direct Source Direct The result of an instruction using this addressing mode is placed in either the A register or the X register, which is specified as part of the instruction opcode. Operand 1 is an address that points to a location in either the RAM memory space or the register space that is the source for the instruction. Arithmetic instructions require two sources; the second source is the A register or X register specified in the opcode. Instructions using this addressing mode are two bytes in length. The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is an address that points to the location of the result. The source for the instruction is either the A register or the X register, which is specified as part of the instruction opcode. Arithmetic instructions require two sources; the second source is the location specified by Operand 1. Instructions using this addressing mode are two bytes in length. Table 12.Destination Direct Opcode Opcode Instruction Operand 1 Instruction Table 10.Source Direct Operand 1 Source Address Destination Address Examples ADD [7], A ;In this case, the value in the memory location at address 7 is added with the Accumulator, and the result is placed in the memory location at address 7. The Accumulator is unchanged. MOV REG[8], A ;In this case, the Accumulator is moved to the register space location at address 8. The Accumulator is unchanged. Examples ADD A, [7] ;In this case, the value in the RAM memory location at address 7 is added with the Accumulator, and the result is placed in the Accumulator. MOV X, REG[8] ;In this case, the value in the register space at address 8 is moved to the X register. Source Indexed Destination Indexed The result of an instruction using this addressing mode is placed in either the A register or the X register, which is specified as part of the instruction opcode. Operand 1 is added to the X register forming an address that points to a location in either the RAM memory space or the register space that is the source for the instruction. Arithmetic instructions require two sources; the second source is the A register or X register specified in the opcode. Instructions using this addressing mode are two bytes. The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is added to the X register forming the address that points to the location of the result. The source for the instruction is the A register. Arithmetic instructions require two sources; the second source is the location specified by Operand 1 added with the X register. Instructions using this addressing mode are two bytes in length. Table 13.Destination Indexed Table 11.Source Indexed Opcode Instruction Opcode Operand 1 Operand 1 Instruction Destination Index Source Index Example ADD Document 38-16016 Rev. *C [X+7], A ;In this case, the value in the memory location at address X+7 is added with the Accumulator and the result is placed in the memory location at address X+7. The Accumulator is unchanged. Page 10 of 62 [+] Feedback CY7C601xx CY7C602xx Table 16.Destination Direct Source Direct Destination Direct Source Immediate The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is the address of the result. The source for the instruction is Operand 2, which is an immediate value. Arithmetic instructions require two sources; the second source is the location specified by Operand 1. Instructions using this addressing mode are three bytes in length. Opcode Operand 1 Instruction Operand 2 Destination Address Source Address Example MOV [7], [8] ;In this case, the value in the memory location at address 8 is moved to the memory location at address 7. Table 14.Destination Direct Source Immediate Opcode Instruction Operand 1 Operand 2 Destination Address Immediate Value Examples ADD [7], 5 ;In this case, value in the memory location at address 7 is added to the immediate value of 5, and the result is placed in the memory location at address 7. MOV REG[8], 6 ;In this case, the immediate value of 6 is moved into the register space location at address 8. Source Indirect Post Increment The result of an instruction using this addressing mode is placed in the Accumulator. Operand 1 is an address pointing to a location within the memory space, which contains an address (the indirect address) for the source of the instruction. The indirect address is incremented as part of the instruction execution. This addressing mode is only valid on the MVI instruction. The instruction using this addressing mode is two bytes in length. Refer to the PSoC Designer: Assembly Language User Guide for further details on MVI instruction. Table 17.Source Indirect Post Increment Opcode Destination Indexed Source Immediate Instruction The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is added to the X register to form the address of the result. The source for the instruction is Operand 2, which is an immediate value. Arithmetic instructions require two sources; the second source is the location specified by Operand 1 added with the X register. Instructions using this addressing mode are three bytes in length. Table 15.Destination Indexed Source Immediate Opcode Instruction Operand 1 Destination Index Operand 2 Immediate Value Examples ADD [X+7], 5 ;In this case, the value in the memory location at address X+7 is added with the immediate value of 5, and the result is placed in the memory location at address X+7. MOV REG[X+8], 6 ;In this case, the immediate value of 6 is moved into the location in the register space at address X+8. Destination Direct Source Direct The result of an instruction using this addressing mode is placed within the RAM memory. Operand 1 is the address of the result. Operand 2 is an address that points to a location in the RAM memory that is the source for the instruction. This addressing mode is only valid on the MOV instruction. The instruction using this addressing mode is three bytes in length. Document 38-16016 Rev. *C Operand 1 Source Address Address Example MVI A, [8] ;In this case, the value in the memory location at address 8 is an indirect address. The memory location pointed to by the Indirect address is moved into the Accumulator. The indirect address is then incremented. Destination Indirect Post Increment The result of an instruction using this addressing mode is placed within the memory space. Operand 1 is an address pointing to a location within the memory space, which contains an address (the indirect address) for the destination of the instruction. The indirect address is incremented as part of the instruction execution. The source for the instruction is the Accumulator. This addressing mode is only valid on the MVI instruction. The instruction using this addressing mode is two bytes in length. Table 18.Destination Indirect Post Increment Opcode Operand 1 Instruction Destination Address Address Example MVI [8], A ;In this case, the value in the memory location at address 8 is an indirect;address. The Accumulator is moved into the memory location pointed to by the indirect address. The indirect address is then incremented. Page 11 of 62 [+] Feedback CY7C601xx CY7C602xx Instruction Set Summary The instruction set is summarized in Table 19 numerically and serves as a quick reference. If more information is needed, the Instruction Set Summary tables are described in detail in the PSoC Designer Assembly Language User Guide (available on the www.cypress.com web site). Bytes Flags Cycles Instruction Format Opcode Hex Bytes Flags Cycles Instruction Format Opcode Hex Bytes Cycles Opcode Hex Table 19.Instruction Set Summary Sorted Numerically by Opcode Order[1, 2] Instruction Format Flags 00 15 1 SSC 2D 8 2 OR [X+expr], A Z 5A 5 2 MOV [expr], X 01 4 2 ADD A, expr C, Z 2E 9 3 OR [expr], expr Z 5B 4 1 MOV A, X 02 6 2 ADD A, [expr] C, Z 2F 10 3 OR [X+expr], expr Z 5C 4 1 MOV X, A 03 7 2 ADD A, [X+expr] C, Z 30 9 1 HALT 5D 6 2 MOV A, reg[expr] Z 04 7 2 ADD [expr], A C, Z 31 4 2 XOR A, expr Z 5E 7 2 MOV A, reg[X+expr] Z 05 8 2 ADD [X+expr], A C, Z 32 6 2 XOR A, [expr] Z 5F 10 3 MOV [expr], [expr] 06 9 Z 3 ADD [expr], expr C, Z 33 7 2 XOR A, [X+expr] Z 60 5 2 MOV reg[expr], A 07 10 3 ADD [X+expr], expr C, Z 34 7 2 XOR [expr], A Z 61 6 2 MOV reg[X+expr], A 08 4 1 PUSH A 35 8 2 XOR [X+expr], A Z 62 8 3 MOV reg[expr], expr 09 4 2 ADC A, expr C, Z 36 9 3 XOR [expr], expr Z 63 9 3 MOV reg[X+expr], expr 0A 6 2 ADC A, [expr] C, Z 37 10 3 XOR [X+expr], expr Z 64 4 1 ASL A C, Z 0B 7 2 ADC A, [X+expr] C, Z 38 5 2 ADD SP, expr 65 7 2 ASL [expr] C, Z 0C 7 2 ADC [expr], A C, Z 39 5 2 CMP A, expr 66 8 2 ASL [X+expr] C, Z 0D 8 2 ADC [X+expr], A C, Z 3A 7 2 CMP A, [expr] 67 4 1 ASR A C, Z 0E 9 3 ADC [expr], expr C, Z 3B 8 2 CMP A, [X+expr] 68 7 2 ASR [expr] C, Z 0F 10 3 ADC [X+expr], expr C, Z 3C 8 3 CMP [expr], expr 69 8 2 ASR [X+expr] C, Z 10 4 1 PUSH X 3D 9 3 CMP [X+expr], expr 6A 4 1 RLC A C, Z 11 4 2 SUB A, expr C, Z 3E 10 2 MVI A, [ [expr]++ ] 6B 7 2 RLC [expr] C, Z 12 6 2 SUB A, [expr] C, Z 3F 10 2 MVI [ [expr]++ ], A 6C 8 2 RLC [X+expr] C, Z 13 7 2 SUB A, [X+expr] C, Z 40 4 1 NOP 6D 4 1 RRC A C, Z 14 7 2 SUB [expr], A C, Z 41 9 3 AND reg[expr], expr Z 6E 7 2 RRC [expr] C, Z 15 8 2 SUB [X+expr], A C, Z 42 10 3 AND reg[X+expr], expr Z 6F 8 2 RRC [X+expr] C, Z 16 9 3 SUB [expr], expr C, Z 43 3 OR reg[expr], expr Z 70 4 2 AND F, expr C, Z 17 10 3 SUB [X+expr], expr C, Z 44 10 3 OR reg[X+expr], expr Z 71 4 2 OR F, expr C, Z 18 5 1 POP A 45 3 XOR reg[expr], expr Z 72 4 2 XOR F, expr C, Z 19 4 2 SBB A, expr 3 XOR reg[X+expr], expr Z 73 4 1 CPL A Z C, Z 9 9 46 10 if (A=B) Z=1 if (A<B) C=1 Z Z Notes 1. Interrupt routines take 13 cycles before execution resumes at interrupt vector table. 2. The number of cycles required by an instruction is increased by one for instructions that span 256-byte boundaries in the Flash memory space. Document 38-16016 Rev. *C Page 12 of 62 [+] Feedback CY7C601xx CY7C602xx Bytes Flags Cycles Instruction Format Opcode Hex Bytes Flags Cycles Instruction Format Opcode Hex Bytes Cycles Opcode Hex Table 19.Instruction Set Summary Sorted Numerically by Opcode Order[1, 2] (continued) Instruction Format Flags 1A 6 2 SBB A, [expr] C, Z 47 8 3 TST [expr], expr Z 74 4 1 INC A C, Z 1B 7 2 SBB A, [X+expr] C, Z 48 9 3 TST [X+expr], expr Z 75 4 1 INC X C, Z 1C 7 2 SBB [expr], A C, Z 49 9 3 TST reg[expr], expr Z 76 7 2 INC [expr] C, Z 1D 8 2 SBB [X+expr], A C, Z 4A 10 3 TST reg[X+expr], expr Z 77 8 2 INC [X+expr] C, Z 1E 9 3 SBB [expr], expr C, Z 4B 5 1 SWAP A, X Z 78 4 1 DEC A C, Z 1F 10 3 SBB [X+expr], expr C, Z 4C 7 2 SWAP A, [expr] Z 79 4 1 DEC X C, Z 20 5 1 POP X 4D 7 2 SWAP X, [expr] 7A 7 2 DEC [expr] C, Z 21 4 2 AND A, expr Z 4E 5 1 SWAP A, SP 7B 8 2 DEC [X+expr] C, Z 22 6 2 AND A, [expr] Z 4F 4 1 MOV X, SP 23 7 2 AND A, [X+expr] Z 50 4 2 MOV A, expr 24 7 2 AND [expr], A Z 51 5 2 MOV A, [expr] 25 8 2 AND [X+expr], A Z 52 6 2 MOV A, [X+expr] 26 9 Z 7C 13 3 LCALL Z 7D 7 3 LJMP Z 7E 10 1 RETI Z 7F 8 1 RET 5 2 JMP 3 AND [expr], expr Z 53 5 2 MOV [expr], A 8x 27 10 3 AND [X+expr], expr Z 54 6 2 MOV [X+expr], A 9x 11 2 CALL 28 11 1 ROMX Z 55 8 3 MOV [expr], expr Ax 5 2 JZ 29 4 2 OR A, expr Z 56 9 3 MOV [X+expr], expr Bx 5 2 JNZ 2A 6 2 OR A, [expr] Z 57 4 2 MOV X, expr Cx 5 2 JC 2B 7 2 OR A, [X+expr] Z 58 6 2 MOV X, [expr] Dx 5 2 JNC 2C 7 2 OR [expr], A Z 59 7 2 MOV X, [X+expr] Ex 7 2 JACC Fx 13 Document 38-16016 Rev. *C 2 INDEX C, Z Z Page 13 of 62 [+] Feedback CY7C601xx CY7C602xx Memory Organization Flash Program Memory Organization Figure 3. Program Memory Space with Interrupt Vector Table after reset Address 16-bit PC 0x0000 Program execution begins here after a reset 0x0004 POR/LVD 0x0008 INT0 0x000C SPI Transmitter Empty 0x0010 SPI Receiver Full 0x0014 GPIO Port 0 0x0018 GPIO Port 1 0x001C INT1 0x0020 Reserved 0x0024 Reserved 0x0028 Reserved 0x002C Reserved 0x0030 Reserved 0x0034 1-ms Interval timer 0x0038 Programmable Interval Timer 0x003C Timer Capture 0 0x0040 Timer Capture 1 0x0044 16-bit Free Running Timer Wrap 0x0048 INT2 0x004C Reserved 0x0050 GPIO Port 2 0x0054 GPIO Port 3 0x0058 GPIO Port 4 0x005C Reserved 0x0060 Reserved 0x0064 Sleep Timer 0x0068 Program Memory begins here (if below interrupts not used, program memory can start lower) 0x1FFF Document 38-16016 Rev. *C Page 14 of 62 [+] Feedback CY7C601xx CY7C602xx Data Memory Organization The CY7C601xx/CY7C602xx microcontrollers provide up to 256 bytes of data RAM Figure 4. Data Memory Organization after reset Address 8-bit PSP 0x00 Top of RAM Memory Stack begins here and grows upward 0xFF Flash This section describes the Flash block of the enCoRe II LV. Much of the user-visible Flash functionality, including programming and security, are implemented in the M8C Supervisory Read Only Memory (SROM). enCoRe II LV Flash has an endurance of 1000 erase/write cycles and a 10-year data retention capability. Flash Programming and Security All Flash programming is performed by code in the SROM. The registers that control the Flash programming are only visible to the M8C CPU when it is executing out of SROM. This makes it impossible to read, write, or erase the Flash by bypassing the security mechanisms implemented in the SROM. Customer firmware can only program the Flash via SROM calls. The data or code images can be sourced via any interface with the appropriate support firmware. This type of programming requires a ‘boot-loader’—a piece of firmware resident on the Flash. For safety reasons this boot-loader should not be overwritten during firmware rewrites. The Flash provides four extra auxiliary rows that are used to hold Flash block protection flags, boot time calibration values, configuration tables, and any device values. The routines for accessing these auxiliary rows are documented in the SROM section. The auxiliary rows are not affected by the device erase function. programming mode and then to use the test queue to issue Flash access functions in the SROM. SROM The SROM holds code that is used to boot the part, calibrate circuitry, and perform Flash operations (Table 20 lists the SROM functions). The functions of the SROM may be accessed in normal user code or operating from Flash. The SROM exists in a separate memory space from user code. The SROM functions are accessed by executing the Supervisory System Call instruction (SSC), which has an opcode of 00h. Prior to executing the SSC the M8C’s accumulator needs to be loaded with the desired SROM function code from Table 20. Undefined functions will cause a HALT if called from user code. The SROM functions are executing code with calls; therefore, the functions require stack space. With the exception of Reset, all of the SROM functions have a parameter block in SRAM that must be configured before executing the SSC. Table 21 lists all possible parameter block variables. The meaning of each parameter, with regards to a specific SROM function, is described later in this chapter . Table 20.SROM Function Codes Function Code Function Name Stack Space 00h SWBootReset 0 01h ReadBlock 7 In-System Programming 02h WriteBlock 10 enCoRe II LV devices enable this type of in-system programming by using the P1.0 and P1.1 pins as the serial programming mode interface. This allows an external controller to cause the enCoRe II LV part to enter serial 03h EraseBlock 9 05h EraseAll 11 Document 38-16016 Rev. *C 06h TableRead 3 07h CheckSum 3 Page 15 of 62 [+] Feedback CY7C601xx CY7C602xx Two important variables that are used for all functions are KEY1 and KEY2. These variables are used to help discriminate between valid SSCs and inadvertent SSCs. KEY1 must always have a value of 3Ah, while KEY2 must have the same value as the stack pointer when the SROM function begins execution. This would be the Stack Pointer value when the SSC opcode is executed, plus three. If either of the keys do not match the expected values, the M8C will halt (with the exception of the SWBootReset function). The following code puts the correct value in KEY1 and KEY2. The code starts with a halt, to force the program to jump directly into the setup code and not run into it. halt SSCOP: mov [KEY1], 3ah mov X, SP mov A, X add A, 3 mov [KEY2], A Table 21.SROM Function Parameters loops through the number of Flash macros in the product, executing the following sequence: erase, bulk program all zeros, erase. After all the user space in all the Flash macros are erased, a second loop erases and then programs each protection block with zeros. SROM Function Descriptions SWBootReset Function The SROM function, SWBootReset, is the function that is responsible for transitioning the device from a reset state to running user code. The SWBootReset function is executed whenever the SROM is entered with an M8C accumulator value of 00h: the SRAM parameter block is not used as an input to the function. This will happen, by design, after a hardware reset, because the M8C's accumulator is reset to 00h or when user code executes the SSC instruction with an accumulator value of 00h. The SWBootReset function will not execute when the SSC instruction is executed with a bad key value and a non-zero function code. An enCoRe II LV device will execute the HALT instruction if a bad value is given for either KEY1 or KEY2. Key1/Counter/Return Code 0,F8h The SWBootReset function verifies the integrity of the calibration data by way of a 16-bit checksum, before releasing the M8C to run user code. Key2/TMP 0,F9h ReadBlock Function BlockID 0,FAh Pointer 0,FBh The ReadBlock function is used to read 64 contiguous bytes from Flash: a block. Clock 0,FCh Mode 0,FDh Delay 0,FEh PCL 0,FFh Variable Name SRAM Address Return Codes The SROM also features Return Codes and Lockouts. The first thing this function does is to check the protection bits and determine if the desired BLOCKID is readable. If read protection is turned on, the ReadBlock function will exit setting the accumulator and KEY2 back to 00h. KEY1 will have a value of 01h, indicating a read failure. If read protection is not enabled, the function will read 64 bytes from the Flash using a ROMX instruction and store the results in SRAM using an MVI instruction. The first of the 64 bytes will be stored in SRAM at the address indicated by the value of the POINTER parameter. When the ReadBlock completes successfully the accumulator, KEY1 and KEY2 will all have a value of 00h. Return codes aid in the determination of success or failure of a particular function. The return code is stored in KEY1’s position in the parameter block. The CheckSum and TableRead functions do not have return codes because KEY1’s position in the parameter block is used to return other data. Table 23.ReadBlock Parameters KEY1 0,F8h 3Ah Table 22.SROM Return Codes KEY2 0,F9h Stack Pointer value, when SSC is executed BLOCKID 0,FAh Flash block number POINTER 0,FBh First of 64 addresses in SRAM where returned data should be stored Return Code Description 00h Success 01h Function not allowed due to level of protection on block 02h Software reset without hardware reset 03h Fatal error, SROM halted Read, write, and erase operations may fail if the target block is read or write protected. Block protection levels are set during device programming. The EraseAll function overwrites data in addition to leaving the entire user Flash in the erase state. The EraseAll function Document 38-16016 Rev. *C Name Address Description WriteBlock Function The WriteBlock function is used to store data in the Flash. Data is moved 64 bytes at a time from SRAM to Flash using this function. The first thing the WriteBlock function does is to check the protection bits and determine if the desired BLOCKID is writable. If write protection is turned on, the WriteBlock function will exit setting the accumulator and KEY2 back to 00h. KEY1 will have a value of 01h, indicating a write failure. Page 16 of 62 [+] Feedback CY7C601xx CY7C602xx The configuration of the WriteBlock function is straightforward. The BLOCKID of the Flash block, where the data is stored, must be determined and stored at SRAM address FAh. Table 25.EraseBlock Parameters The SRAM address of the first of the 64 bytes to be stored in Flash must be indicated using the POINTER variable in the parameter block (SRAM address FBh). Finally, the CLOCK and DELAY value must be set correctly. The CLOCK value determines the length of the write pulse that will be used to store the data in the Flash. The CLOCK and DELAY values are dependent on the CPU speed and must be set correctly. Refer to “Clocking” Section for additional information. KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value, when SSC is executed BLOCKID 0,FAh Flash block number (00h–7Fh) CLOCK 0,FCh Clock Divider used to set the erase pulse width DELAY 0,FEh For a CPU speed of 12 MHz set to 56h Name Address Table 24.WriteBlock Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value, when SSC is executing BLOCK ID 0,FAh 8KB Flash block number (00h–7Fh) 4KB Flash block number (00h–3Fh) 3KB Flash block number (00h–2Fh) POINTER 0,FBh First 64 addresses in SRAM where the data to be stored in Flash is located prior to calling WriteBlock CLOCK 0,FCh Clock Divider used to set the write Pulse width DELAY 0,FEh For a CPU speed of 12 MHz set to 56h EraseBlock Function The EraseBlock function is used to erase a block of 64 contiguous bytes in Flash. The first thing the EraseBlock function does is to check the protection bits and determine if the desired BLOCKID is writable. If write protection is turned on, the EraseBlock function will exit setting the accumulator and KEY2 back to 00h. KEY1 will have a value of 01h, indicating a write failure. The EraseBlock function is only useful as the first step in programming. Erasing a block will not cause data in a block to be one hundred percent unreadable. If the objective is to obliterate data in a block, the best method is to perform an EraseBlock followed by a WriteBlock of all zeros. To set up the parameter block for the EraseBlock function, correct key values must be stored in KEY1 and KEY2. The block number to be erased must be stored in the BLOCKID variable and the CLOCK and DELAY values must be set based on the current CPU speed. Description ProtectBlock Function The enCoRe II LV devices offer Flash protection on a blockby-block basis. Table 26 lists the protection modes available. In the table, ER and EW are used to indicate the ability to perform external reads and writes. For internal writes, IW is used. Internal reading is always permitted by way of the ROMX instruction. The ability to read by way of the SROM ReadBlock function is indicated by SR. The protection level is stored in two bits according to Table 26. These bits are bit packed into the 64 bytes of the protection block. Therefore, each protection block byte stores the protection level for four Flash blocks. The bits are packed into a byte, with the lowest numbered block’s protection level stored in the lowest numbered bits Table 26. The first address of the protection block contains the protection level for blocks 0 through 3; the second address is for blocks 4 through 7. The 64th byte will store the protection level for blocks 252 through 255. Table 26.Protection Modes Mode Settings Description Marketing 00b SR ER EW IW Unprotected Unprotected 01b SR ER EW IW Read protect Factory upgrade 10b SR ER EW IW Disable external Field upgrade write 11b SR ER EW IW Disable internal write 7 6 Block n+3 5 4 Block n+2 3 Full protection 2 Block n+1 1 0 Block n The level of protection is only decreased by an EraseAll, which places zeros in all locations of the protection block. To set the level of protection, the ProtectBlock function is used. This function takes data from SRAM, starting at address 80h, and ORs it with the current values in the protection block. The result of the OR operation is then stored in the protection block. The EraseBlock function does not change the protection level for a block. Because the SRAM location for the protection data is fixed and there is only one protection block per Flash macro, the ProtectBlock function expects very few variables in the parameter block to be set prior to calling the function. The parameter block values that must be set, besides the keys, are the CLOCK and DELAY values. Document 38-16016 Rev. *C Page 17 of 62 [+] Feedback CY7C601xx CY7C602xx Table 27.ProtectBlock Parameters Name Address Description Table 29.Table Read Parameters Name Address Description KEY1 0,F8h 3Ah KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value when SSC is executed KEY2 0,F9h Stack Pointer value when SSC is executed CLOCK 0,FCh Clock Divider used to set the write pulse width BLOCKID 0,FAh DELAY 0,FEh For a CPU speed of 12 MHz set to 56h EraseAll Function The table space for the enCoRe II LV is simply a 64-byte row broken up into eight tables of eight bytes. The tables are numbered zero through seven. All user and hidden blocks in the enCoRe II LV parts consist of 64 bytes. The EraseAll function performs a series of steps that destroy the user data in the Flash macros and resets the protection block in each Flash macro to all zeros (the unprotected state). The EraseAll function does not affect the three hidden blocks above the protection block, in each Flash macro. The first of these four hidden blocks is used to store the protection table for its eight Kbytes of user data. An internal table holds the Silicon ID and returns the Revision ID. The Silicon ID is returned in SRAM, while the Revision ID is returned in the CPU_A and CPU_X registers. The Silicon ID is a value placed in the table by programming the Flash and is controlled by Cypress Semiconductor Product Engineering. The Revision ID is hard-coded into the SROM. The Revision ID is discussed in more detail later in this section. The EraseAll function begins by erasing the user space of the Flash macro with the highest address range. A bulk program of all zeros is then performed on the same Flash macro, to destroy all traces of the previous contents. The bulk program is followed by a second erase that leaves the Flash macro in a state ready for writing. The erase, program, erase sequence is then performed on the next lowest Flash macro in the address space if it exists. Following the erase of the user space, the protection block for the Flash macro with the highest address range is erased. Following the erase of the protection block, zeros are written into every bit of the protection table. The next lowest Flash macro in the address space then has its protection block erased and filled with zeros. An internal table holds alternate trim values for the device and returns a one-byte internal revision counter. The internal revision counter starts out with a value of zero and is incremented each time one of the other revision numbers is not incremented. It is reset to zero each time one of the other revision numbers is incremented. The internal revision count is returned in the CPU_A register. The CPU_X register will always be set to FFh when trim values are read. The BLOCKID value, in the parameter block, is used to indicate which table should be returned to the user. Only the three least significant bits of the BLOCKID parameter are used by TableRead function for the enCoRe II LV. The upper five bits are ignored. When the function is called, it transfers bytes from the table to SRAM addresses F8h–FFh. The end result of the EraseAll function is that all user data in the Flash is destroyed and the Flash is left in an unprogrammed state, ready to accept one of the various write commands. The protection bits for all user data are also reset to the zero state. The M8C’s A and X registers are used by the TableRead function to return the die’s Revision ID. The Revision ID is a 16-bit value hard-coded into the SROM that uniquely identifies the die’s design. The parameter block values that must be set, besides the keys, are the CLOCK and DELAY values. Table 28.EraseAll Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value when SSC is executed CLOCK 0,FCh Clock Divider used to set the write pulse width DELAY 0,FEh For a CPU speed of 12 MHz set to 56h Checksum Function The Checksum function calculates a 16-bit checksum over a user-specifiable number of blocks, within a single Flash macro (Bank) starting from block zero. The BLOCKID parameter is used to pass in the number of blocks to calculate the checksum over. A BLOCKID value of 1 will calculate the checksum of only block 0, while a BLOCKID value of 0 will calculate the checksum of all 256-user blocks. The 16-bit checksum is returned in KEY1 and KEY2. The parameter KEY1 holds the lower eight bits of the checksum and the parameter KEY2 holds the upper eight bits of the checksum. The checksum algorithm executes the following sequence of three instructions over the number of blocks times 64 to be checksummed. TableRead Function romx The TableRead function gives the user access to part-specific data stored in the Flash during manufacturing. It also returns a Revision ID for the die (not to be confused with the Silicon ID). add [KEY1], A Document 38-16016 Rev. *C Table number to read adc [KEY2], 0 Page 18 of 62 [+] Feedback CY7C601xx CY7C602xx Table 30.Checksum Parameters Name Address Table 31.Oscillator Trim Values vs. Voltage Settings Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value when SSC is executed BLOCKID 0,FAh Supervisory FLASH User Row Address Number of Flash blocks to calculate checksum on Function 0xC094 24-MHz IOSCTR @ 3.30V 0xC095 24-MHz IOSCTR @ 3.00V 0xC096 24-MHz IOSCTR @ 2.85V 0xC097 24-MHz IOSCTR @ 2.70V 0xC098 32-kHz [email protected] Clocking 0xC099 32-kHz [email protected] The enCoRe II LV internal oscillator outputs two frequencies, the Internal 24 MHz Oscillator and the 32 kHz Low-power Oscillator. 0xC09A 32-kHz [email protected] 0xC09B 32-kHz [email protected] The Internal 24 MHz Oscillator is designed such that it may be trimmed to an output frequency of 24 MHz over temperature and voltage variation. The Internal 24 MHz Oscillator accuracy is 24 MHz –22% to +10% (between 0° and 70°C). No external components are required to achieve this level of accuracy. When using the 32 kHz oscillator the PITMRL/H should be read until 2 consecutive readings match before sending/receiving data. The following firmware example assumes the developer is interested in the lower byte of the PIT. Firmware is responsible for selecting the correct trim values from the User row to match the power supply voltage in the end application and writing the values to the trim registers IOSCTR and LPOSCTR. Read_PIT_counter: The internal low-speed oscillator of nominally 32 kHz provides a slow clock source for the enCoRe II LV in suspend mode, particularly to generate a periodic wake-up interrupt and also to provide a clock to sequential logic during power-up and power-down events when the main clock is stopped. In addition, this oscillator can also be used as a clocking source for the Interval Timer clock (ITMRCLK) and Capture Timer clock (TCAPCLK). The 32 kHz Low-power Oscillator can operate in low-power mode or can provide a more accurate clock in normal mode. The Internal 32 kHz Low-power Oscillator accuracy ranges from –53.12% to +56.25%. The 32 kHz low power oscillator can be calibrated against the internal 24 MHz oscillator or another timing source if desired. mov A, reg[PITMRL] enCoRe II LV provides the ability to load new trim values for the 24-MHz oscillator based on voltage. This allows Vdd to be monitored and have firmware trim the oscillator based on voltage present. The IOSCTR register is used to set trim values for the 24-MHz oscillator. enCoRe II LV is initialized with 3.30V trim values at power-on, then firmware is responsible for transferring the correct set of trim values to the trim registers to match the application’s actual Vdd. The 32 kHz oscillator generally does not require trim adjustments vs. voltage but trim values for the 32 kHz are also stored in Supervisory ROM. mov A, [59h] mov A, reg[PITMRL] mov [57h], A mov [58h],A mov [59h], A mov A, reg[PITMRL] mov [60h], A ;;;Start comparison mov A,[60h] mov X, [59h] sub A, [59h] jz done mov X, [58h] sub A, [58h] jz done mov X, [57h] ;;;correct data is in memory location 57h done: mov [57h], X ret The CY7C601xx part can optionally be sourced from an external crystal oscillator. The external clock driving on CLKIN range is from 187 KHz to 24 MHz. Clock Architecture Description The enCoRe II LV clock selection circuitry allows the selection of independent clocks for the CPU, Interval Timers and Capture Timers. Document 38-16016 Rev. *C Page 19 of 62 [+] Feedback CY7C601xx CY7C602xx On the CY7C601xx, the external oscillator can be sourced by the crystal oscillator or when the crystal oscillator is disabled it is sourced directly from the CLKIN pin. The external crystal oscillator is fed through the EFTB block, which can optionally be bypassed. CPU Clock The CPU clock, CPUCLK, can be sourced from the external crystal oscillator, the Internal 24 MHz Oscillator, or the Internal 32 kHz Low-power Oscillator. The selected clock source can optionally be divided by 2n-1 where n is 0–7 (see Table 33). When it is not being used by the external crystal oscillator, the CLKOUT pin can be driven from one of many sources. This is used for test and can also be used in some applications. The sources that can drive the CLKOUT are: • CLKIN after the optional EFTB filter • Internal 24 MHz Oscillator • Internal 32 kHz Oscillator • CPUCLK after the programmable divider Figure 5. CPU Clock Block Diagram XOSC SEL EN P0.1 CLKOUT XTAL OSC 1-24MHz P0.0 CLKIN EFTB CY7C601xx only CLK_EXT MUX CY7C601xx only Crystal Oscillator Disabled LP OSC 32-KHz CLK_32KHz CPUCLK SEL CLK_EXT SCALE (divide by 2n, n = 0-5,7) CLK_CPU Doubler CLK_HS MUX CLK_24MHz Document 38-16016 Rev. *C Page 20 of 62 [+] Feedback CY7C601xx CY7C602xx Table 32.CPU Clock Config (CPUCLKCR) [0x30] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Reserved CPUCLK Select Read/Write – – – – – – – R/W Default 0 0 0 0 0 0 0 0 Bit [7:1]: Reserved Bit 0: CPU CLK Select 0 = Internal 24 MHz Oscillator. 1 = External crystal oscillator—External crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled, CLKIN input if the external crystal oscillator is disabled. Note: the CPU speed selection is configured using the OSC_CR0 Register (Table 6.) Table 33.OSC Control 0 (OSC_CR0) [0x1E0] [R/W] Bit # 7 Field 6 5 Reserved 4 No Buzz 3 2 Sleep Timer [1:0] 1 0 CPU Speed [2:0] Read/Write – – R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit [7:6]: Reserved Bit 5: No Buzz During sleep (the Sleep bit is set in the CPU_SCR Register—Table 39), the LVD and POR detection circuit is turned on periodically to detect any POR and LVD events on the VCC pin (the Sleep Duty Cycle bits in the ECO_TR are used to control the duty cycle—Table 43). To facilitate the detection of POR and LVD events, the No Buzz bit is used to force the LVD and POR detection circuit to be continuously enabled during sleep. This results in a faster response to an LVD or POR event during sleep at the expense of a slightly higher than average sleep current. Obtaining the absolute lowest power usage in sleep mode requires the No Buzz bit be clear. 0 = The LVD and POR detection circuit is turned on periodically as configured in the Sleep Duty Cycle. 1 = The Sleep Duty Cycle value is overridden. The LVD and POR detection circuit is always enabled. Note: The periodic Sleep Duty Cycle enabling is independent with the sleep interval shown in the Sleep [1:0] bits below. Bit [4:3]: Sleep Timer [1:0] Sleep Timer [1:0] Sleep Timer Clock Sleep Period Frequency (Nominal) (Nominal) Watchdog Period (Nominal) 00 512 Hz 1.95 ms 6 ms 01 64 Hz 15.6 ms 47 ms 10 8 Hz 125 ms 375 ms 11 1 Hz 1 sec 3 sec Note: Sleep intervals are approximate. Bit [2:0]: CPU Speed [2:0] The enCoRe II LV may operate over a range of CPU clock speeds. The reset value for the CPU Speed bits is zero; therefore, the default CPU speed is 3 MHz. CPU Speed [2:0] CPU when Internal Oscillator is selected External Clock 000 3 MHz (Default) Clock In/8 001 6 MHz Clock In/4 010 12 MHz Clock In/2 011 Reserved Reserved 100 1.5 MHz Clock In/16 101 750 KHz Clock In/32 110 187 KHz Clock In/128 111 Reserved Reserved Document 38-16016 Rev. *C Page 21 of 62 [+] Feedback CY7C601xx CY7C602xx Table 34.Clock I/O Config (CLKIOCR) [0x32] [R/W] Bit # 7 6 5 Reserved Field 4 3 2 XOSC Select XOSC Enable EFTB Disabled 1 0 CLKOUT Select Read/Write – – – R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit [7:5]: Reserved Bit 4: XOSC Select This bit, when set, selects the external crystal oscillator clock as clock source of external clock. Care needs to be taken while selecting the crystal oscillator clock. First enable the crystal oscillator and wait for few cycles, which is oscillator stabilization period. Then select the crystal clock as clock source. Similarly, while deselect crystal clock, first deselect crystal clock as clock source then disable the crystal oscillator 0 = Not select external crystal oscillator clock 1 = Select the external crystal oscillator clock Bit 3: XOSC Enable This bit is only available on the CY7C601xx This bit when set enables the external crystal oscillator. The external crystal oscillator shares pads CLKIN and CLKOUT with two GPIOs—P0.0 and P0.1, respectively. When the external crystal oscillator is enabled, the CLKIN signal comes from the external crystal oscillator block and the output enables on the GPIOs for P0.0 and P0.1 are disabled, eliminating the possibility of contention. When the external crystal oscillator is disabled the source for CLKIN signal comes from the P0.0 GPIO input. 0 = Disable the external oscillator 1 = Enable the external oscillator Note: The external crystal oscillator start-up time takes up to 2 ms. Bit 2: EFTB Disabled This bit is only available on the CY7C601xx. 0 = Enable the EFTB filter 1 = Disable the EFTB filter, causing CLKIN to bypass the EFTB filter Bit [1:0]: CLKOUT Select 0 0 = Internal 24 MHz Oscillator 0 1 = External crystal oscillator – external crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled, CLKIN input if the external oscillator is disabled. 1 0 = Internal 32 kHz Low-power Oscillator 1 1 = CPUCLK Interval Timer Clock (ITMRCLK) The Interval Timer clock (ITMRCLK), can be sourced from the external crystal oscillator, the Internal 24 MHz Oscillator, the Internal 32 kHz Low-power Oscillator, or the Timer Capture clock. A programmable prescaler of 1, 2, 3, 4 then divides the selected source. The 12-bit Programmable Interval Timer is a simple down counter with a programmable reload value. It provides a 1-µs resolution by default. When the down counter reaches zero, the next clock is spent reloading. The reload value can be read and written while the counter is running, but care should be taken to ensure that the counter does not unintentionally reload while the 12-bit reload value is only partially stored—i.e., between the two writes of the 12-bit value. The Programmable interval timer generates an interrupt to the CPU on each reload. Document 38-16016 Rev. *C The parameters to be set will show up on the device editor view of PSoC Designer once you place the enCoRe II LV timer user module. The parameters are PITIMER_Source and PITIMER_Divider. The PITIMER_Source is the clock to the timer and the PITIMER_Divider is the value the clock is divided by. The interval register (PITMR) holds the value that is loaded into the PIT counter on terminal count. The Programmable Interval Timer resolution is configurable. For example: TCAPCLK divide by x of CPU clock (for example TCAPCLK divide by 2 of a 24 MHz CPU clock will give a frequency of 12 MHz) ITMRCLK divide by x of TCAPCLK (for example, ITMRCLK divide by 3 of TCAPCLK is 4 MHz so resolution is 0.25 µs) Page 22 of 62 [+] Feedback CY7C601xx CY7C602xx Figure 6. Programmable Interval Timer Block Diagram Configuration Status and Control System Clock 12-bit reload value 12-bit down counter Clock Timer 12-bit reload control Interrupt Controller Timer Capture Clock (TCAPCLK) The Timer Capture clock (TCAPCLK) can be sourced from the external crystal oscillator, the Internal 24 MHz Oscillator or the Internal 32 kHz Low-power Oscillator. A programmable prescaler of 2, 4, 6, or 8 then divides the selected source. Figure 7. Timer Capture Block Diagram System Clock Configuration Status and Control Captimer Clock 16-bit counter Prescale Mux Capture Registers 1ms timer Overflow Interrupt Capture0 Int Capture1 Int Interrupt Controller Document 38-16016 Rev. *C Page 23 of 62 [+] Feedback CY7C601xx CY7C602xx Table 35.Timer Clock Config (TMRCLKCR) [0x31] [R/W] Bit # 7 Field TCAPCLK Divider 6 5 4 TCAPCLK Select 3 2 1 ITMRCLK Divider 0 ITMRCLK Select Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 1 0 0 0 1 1 1 1 Bit [7:6]: TCAPCLK Divider [1:0] TCAPCLK Divider controls the TCAPCLK divisor. 0 0 = Divider Value 2 0 1 = Divider Value 4 1 0 = Divider Value 6 1 1 = Divider Value 8 Bit [5:4]: TCAPCLK Select The TCAPCLK Select field controls the source of the TCAPCLK. 0 0 = Internal 24 MHz Oscillator 0 1 = External crystal oscillator—external crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled, CLKIN input if the external crystal oscillator is disabled (the XOSC Enable bit of the CLKIOCR Register is cleared—Table 34.) 1 0 = Internal 32 kHz Low-power Oscillator 1 1 = TCAPCLK Disabled Note: The 1024-µs interval timer is based on the assumption that TCAPCLK is running at 4 MHz. Changes in TCAPCLK frequency will cause a corresponding change in the 1024-µs interval timer frequency. Bit [3:2]: ITMRCLK Divider ITMRCLK Divider controls the ITMRCLK divisor. 0 0 = Divider value of 1 0 1 = Divider value of 2 1 0 = Divider value of 3 1 1 = Divider value of 4 Bit [1:0]: ITMRCLK Select 0 0 = Internal 24 MHz Oscillator 0 1 = External crystal oscillator—external crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled, CLKIN input if the external crystal oscillator is disabled. 1 0 = Internal 32 kHz Low-power Oscillator 1 1 = TCAPCLK Note: Changing the source of TMRCLK requires that both the source and destination clocks be running. Attempting to change the clock source away from TCAPCLK after that clock has been stopped will not be successful. Document 38-16016 Rev. *C Page 24 of 62 [+] Feedback CY7C601xx CY7C602xx Internal Clock Trim Table 36.IOSC Trim (IOSCTR) [0x34] [R/W] Bit # 7 6 Field 5 4 3 foffset[2:0] 2 1 0 Gain[4:0] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 D D D D D The IOSC Calibrate register is used to calibrate the internal oscillator. The reset value is undefined but during boot the SROM writes a calibration value that is determined during manufacturing test. The “D” indicates that the default value is trimmed to 24 MHz @ 3.30V at power on. Bit [7:5]: foffset [2:0] This value is used to trim the frequency of the internal oscillator. These bits are not used in factory calibration and will be zero. Setting each of these bits causes the appropriate fine offset in oscillator frequency. foffset bit 0 = 7.5 kHz foffset bit 1 = 15 kHz foffset bit 2 = 30 kHz Bit [4:0]: Gain [4:0] The effective frequency change of the offset input is controlled through the gain input. A lower value of the gain setting increases the gain of the offset input. This value sets the size of each offset step for the internal oscillator. Nominal gain change (KHz/offsetStep) at each bit, typical conditions (24 MHz operation): Gain bit 0 = –1.5 kHz Gain bit 1 = –3.0 kHz Gain bit 2 = –6 kHz Gain bit 3 = –12 kHz Gain bit 4 = –24 kHz External Clock Trim Table 37.XOSC Trim (XOSCTR) [0x35] [R/W] Bit # 7 6 Field 5 4 Reserved 3 2 XOSC XGM [2:0] 1 0 Reserved Mode Read/Write – – – R/W R/W R/W – R/W Default 0 0 0 D D D – D This register is used to calibrate the external crystal oscillator. The reset value is undefined but during boot the SROM writes a calibration value that is determined during manufacturing test. This is the meaning of ‘D’ in the Default field. Bit [7:5]: Reserved Bit [4:2]: XOSC XGM [2:0] Amplifier transconductance setting. The Xgm settings are recommended for resonators with frequencies of interest for the enCoRe II LV as below: Resonator XGM Setting Worst Case R (Ohms) 6 MHz Crystal 001 403 12 MHz Crystal 011 201 Reserved 111 - 6 MHz Ceramic 001 70.4 12 MHz Ceramic 011 41 Bit 1: Reserved Bit 0: Mode 0 = Oscillator Mode 1 = Fixed Maximum Bias test Mode Document 38-16016 Rev. *C Page 25 of 62 [+] Feedback CY7C601xx CY7C602xx LPOSC Trim Table 38.LPOSC Trim (LPOSCTR) [0x36] [R/W] Bit # 7 6 Field 32 kHz Low Power Reserved 5 4 3 Read/Write R/W – R/W R/W R/W R/W R/W R/W Default 0 – D D D D D D 32 kHz Bias Trim [1:0] 2 1 0 32 kHz Freq Trim [3:0] This register is used to calibrate the 32 kHz Low-speed Oscillator. The reset value is undefined but during boot the SROM writes a calibration value that is determined during manufacturing test. This is the meaning of ‘D’ in the Default field. The trim value can be adjusted vs. voltage as noted in Table 32. Bit 7: 32 kHz Low Power 0 = The 32 kHz Low-speed Oscillator operates in normal mode. 1 = The 32 kHz Low-speed Oscillator operates in a low-power mode. The oscillator continues to function normally but with reduced accuracy. Bit 6: Reserved Bit [5:4]: 32 kHz Bias Trim [1:0] These bits control the bias current of the low-power oscillator. 0 0 = Mid bias 0 1 = High bias 1 0 = Reserved 1 1 = Reserved Important Note: Do not program the 32 kHz Bias Trim [1:0] field with the reserved 10b value as the oscillator does not oscillate at all corner conditions with this setting. Bit [3:0]: 32 kHz Freq Trim [3:0] These bits are used to trim the frequency of the low-power oscillator. CPU Clock During Sleep Mode Reset When the CPU enters sleep mode the CPUCLK Select (Bit 0, Table 32) is forced to the Internal Oscillator, and the oscillator is stopped. When the CPU comes out of sleep mode it is running on the internal oscillator. The internal oscillator recovery time is three clock cycles of the Internal 32 kHz Lowpower Oscillator. The microcontroller supports two types of resets: Power-on Reset (POR) and Watchdog Reset (WDR). When reset is initiated, all registers are restored to their default states and all interrupts are disabled. If the system requires the CPU to run off the external clock after awaking from sleep mode, firmware will need to switch the clock source for the CPU. If the external clock source is the external oscillator and the oscillator is disabled, firmware will need to enable the external oscillator, wait for it to stabilize, and then change the clock source. The occurrence of a reset is recorded in the System Status and Control Register (CPU_SCR). Bits within this register record the occurrence of POR and WDR Reset, respectively. The firmware can interrogate these bits to determine the cause of a reset. The microcontroller resumes execution from Flash address 0x0000 after a reset. The internal clocking mode is active after a reset, until changed by user firmware. Note: The CPU clock defaults to 3 MHz (Internal 24 MHz Oscillator divide-by-8 mode) at POR to guarantee operation at the low VCC that might be present during the supply ramp. Document 38-16016 Rev. *C Page 26 of 62 [+] Feedback CY7C601xx CY7C602xx Table 39.System Status and Control Register (CPU_SCR) [0xFF] [R/W] Bit # 7 6 5 4 3 2 1 0 Field GIES Reserved WDRS PORS Sleep Reserved Reserved Stop Read/Write R – R/C[3] R/C[3] R/W – – R/W Default 0 0 0 1 0 1 0 0 The bits of the CPU_SCR register are used to convey status and control of events for various functions of an enCoRe II LV device. Bit 7: GIES The Global Interrupt Enable Status bit is a read only status bit and its use is discouraged. The GIES bit is a legacy bit, which was used to provide the ability to read the GIE bit of the CPU_F register. However, the CPU_F register is now readable. When this bit is set, it indicates that the GIE bit in the CPU_F register is also set which, in turn, indicates that the microprocessor will service interrupts. 0 = Global interrupts disabled 1 = Global interrupt enabled Bit 6: Reserved Bit 5: WDRS The WDRS bit is set by the CPU to indicate that a WDR event has occurred. The user can read this bit to determine the type of reset that has occurred. The user can clear but not set this bit. 0 = No WDR 1 = A WDR event has occurred Bit 4: PORS The PORS bit is set by the CPU to indicate that a POR event has occurred. The user can read this bit to determine the type of reset that has occurred. The user can clear but not set this bit. 0 = No POR 1 = A POR event has occurred. (Note that WDR events will not occur until this bit is cleared.) Bit 3: SLEEP Set by the user to enable CPU sleep state. CPU will remain in sleep mode until any interrupt is pending. The Sleep bit is covered in more detail in the Sleep Mode section. 0 = Normal operation 1 = Sleep Bit [2:1]: Reserved Bit 0: STOP This bit is set by the user to halt the CPU. The CPU will remain halted until a reset (WDR, POR, or external reset) has taken place. If an application wants to stop code execution until a reset, the preferred method would be to use the HALT instruction rather than writing to this bit. 0 = Normal CPU operation 1 = CPU is halted (not recommended) Power-On Reset POR occurs every time the power to the device is switched on. POR is released when the supply is typically 2.6V for the upward supply transition, with typically 50 mV of hysteresis during the power on transient. Bit 4 of the System Status and Control Register (CPU_SCR) is set to record this event (the register contents are set to 00010000 by the POR). After a POR, the microprocessor is held off for approximately 20 ms for the VCC supply to stabilize before executing the first instruction at address 0x00 in the Flash. If the VCC voltage drops below the POR downward supply trip point, POR is reasserted. The VCC supply needs to ramp linearly from 0 to VCC in less than 200 ms. Important: The PORS status bit is set at POR and can only be cleared by the user, and cannot be set by firmware. Watchdog Timer Reset The user has the option to enable the WDT. The WDT is enabled by clearing the PORS bit. Once the PORS bit is cleared, the WDT cannot be disabled. The only exception to this is if a POR event takes place, which will disable the WDT. The sleep timer is used to generate the sleep time period and the Watchdog time period. The sleep timer uses the Internal 32 kHz Low-power Oscillator system clock to produce the sleep time period. The user can program the sleep time period using the Sleep Timer bits of the OSC_CR0 Register (Table 33). When the sleep time elapses (sleep timer overflows), an interrupt to the Sleep Timer Interrupt Vector will be generated. The Watchdog Timer period is automatically set to be three counts of the Sleep Timer overflows. This represents between two and three sleep intervals depending on the count in the Sleep Timer at the previous WDT clear. When this timer reaches three, a WDR is generated. The user can either clear the WDT, or the WDT and the Sleep Timer. Whenever the user writes to the Reset WDT Register (RES_WDT), the WDT will be cleared. If the data that is written is the hex value 0x38, the Sleep Timer will also be cleared at the same time. Note 3. ‘C = Clear. This bit can only be cleared by the user and cannot be set by firmware. Document 38-16016 Rev. *C Page 27 of 62 [+] Feedback CY7C601xx CY7C602xx Table 40.Reset Watchdog Timer (RESWDT) [0xE3] [W] Bit # 7 6 5 Field 4 3 2 1 0 Reset Watchdog Timer [7:0] Read/Write W W W W W W W W Default 0 0 0 0 0 0 0 0 Any write to this register will clear the Watchdog Timer, a write of 0x38 will also clear the Sleep Timer. Bit [7:0]: Reset Watchdog Timer [7:0] Sleep Mode sleep instruction is executed before the interrupt service routine (if enabled). The CPU can only be put to sleep by the firmware. This is accomplished by setting the Sleep bit in the System Status and Control Register (CPU_SCR). This stops the CPU from executing instructions, and the CPU will remain asleep until an interrupt comes pending, or there is a reset event (either a Power-on Reset, or a Watchdog Timer Reset). The Sleep interrupt allows the microcontroller to wake up periodically and poll system components while maintaining very low average power consumption. The Sleep interrupt may also be used to provide periodic interrupts during nonsleep modes. The Low-voltage Detection circuit (LVD) drops into fully functional power-reduced states, and the latency for the LVD is increased. The actual latency can be traded against power consumption by changing Sleep Duty Cycle field of the ECO_TR Register. Sleep Sequence The Internal 32 kHz Low-speed Oscillator remains running. Prior to entering suspend mode, firmware can optionally configure the 32 kHz Low-speed Oscillator to operate in a lowpower mode to help reduce the over all power consumption (using the 32 kHz Low Power bit, Table 38). This will help save approximately 5 µA; however, the trade off is that the 32 kHz Low-speed Oscillator will be less accurate (–53.12% to +56.25% deviation). All interrupts remain active. Only the occurrence of an interrupt will wake the part from sleep. The Stop bit in the System Status and Control Register (CPU_SCR) must be cleared for a part to resume out of sleep. The Global Interrupt Enable bit of the CPU Flags Register (CPU_F) does not have any effect. Any unmasked interrupt will wake the system up. As a result, any interrupts not intended for waking should be disabled through the Interrupt Mask Registers. When the CPU enters sleep mode the CPUCLK Select (Bit 1, Table 32) is forced to the Internal Oscillator. The internal oscillator recovery time is three clock cycles of the Internal 32 kHz Low-power Oscillator. The Internal 24 MHz Oscillator restarts immediately on exiting Sleep mode. If the external crystal oscillator is used, firmware will need to switch the clock source for the CPU. Unlike the Internal 24 MHz Oscillator, the external oscillator is not automatically shut-down during sleep. Systems that need the external oscillator disabled in sleep mode will need to disable the external oscillator prior to entering sleep mode. In systems where the CPU runs off the external oscillator, firmware will need to switch the CPU to the internal oscillator prior to disabling the external oscillator. On exiting sleep mode, once the clock is stable and the delay time has expired, the instruction immediately following the Document 38-16016 Rev. *C The SLEEP bit is an input into the sleep logic circuit. This circuit is designed to sequence the device into and out of the hardware sleep state. The hardware sequence to put the device to sleep is shown in Figure 8 and is defined as follows. 1. Firmware sets the SLEEP bit in the CPU_SCR0 register. The Bus Request (BRQ) signal to the CPU is immediately asserted. This is a request by the system to halt CPU operation at an instruction boundary. The CPU samples BRQ on the positive edge of CPUCLK. 2. Due to the specific timing of the register write, the CPU issues a Bus Request Acknowledge (BRA) on the following positive edge of the CPU clock. The sleep logic waits for the following negative edge of the CPU clock and then asserts a system-wide Power Down (PD) signal. In Figure 8 the CPU is halted and the system-wide power down signal is asserted. 3. The system-wide PD (power down) signal controls several major circuit blocks: The Flash memory module, the internal 24-MHz oscillator, the EFTB filter and the bandgap voltage reference. These circuits transition into a zero power state. The only operational circuits on chip are the Low Power oscillator, the bandgap refresh circuit, and the supply voltage monitor (POR/LVD) circuit. The external crystal oscillator on enCoRe II LV devices is not automatically powered down when the CPU enters the sleep state. Firmware must explicitly disable the external crystal oscillator in order to reduce power to levels specified. Note: To achieve the lowest possible power consumption during suspend/sleep, the following conditions must be observed in addition to considerations for the sleep timer and external crystal oscillator: • All GPIOs must be set to outputs and driven low • The port pins P1.0 and P1.1 should be configured as inputs with their pull ups enabled. Page 28 of 62 [+] Feedback CY7C601xx CY7C602xx Figure 8. Sleep Timing Firmware write to SCR SLEEP bit causes an immediate BRQ CPU captures BRQ on next CPUCLK edge CPU responds with a BRA On the falling edge of CPUCLK, PD is asserted. The 24/48 MHz system clock is halted; the Flash and bandgap are powered down CPUCLK IOW SLEEP BRQ BRA PD Wakeup Sequence Once asleep, the only event that can wake the system up is an interrupt. The global interrupt enable of the CPU flag register does not need to be set. Any unmasked interrupt will wake the system up. It is optional for the CPU to actually take the interrupt after the wakeup sequence. The wakeup sequence is synchronized to the 32 kHz clock for purposes of sequencing a startup delay, to allow the Flash memory module enough time to power up before the CPU asserts the first read access. Another reason for the delay is to allow the oscillator, Bandgap, and LVD/POR circuits time to settle before actually being used in the system. As shown in Figure 9, the wakeup sequence is as follows: 1. The wakeup interrupt occurs and is synchronized by the negative edge of the 32 kHz clock. 2. At the following positive edge of the 32 kHz clock, the system wide PD signal is negated. The Flash memory Document 38-16016 Rev. *C module, internal oscillator, EFTB, and bandgap circuit are all powered up to a normal operating state. 3. At the following positive edge of the 32 kHz clock, the current values for the precision POR and LVD have settled and are sampled. 4. At the following negative edge of the 32 kHz clock (after about 15 µs nominal), the BRQ signal is negated by the sleep logic circuit. On the following CPUCLK, BRA is negated by the CPU and instruction execution resumes. Note that in Figure 9 fixed function blocks, such as Flash, internal oscillator, EFTB, and bandgap, have about 15 µs start up. The wakeup times (interrupt to CPU operational) will range from 75 µs to 105 µs. Page 29 of 62 [+] Feedback CY7C601xx CY7C602xx Figure 9. Wakeup Timing S le e p T im e r o r G P IO in te rru p t o ccu rs In te rru p t is d o u b le sa m p le d b y 3 2 K clo ck a n d P D is n e g a te d to syste m C P U is re sta rte d a fte r 9 0 m s (n o m in a l) CLK32K IN T SLEEP PD BANDGAP ENABLE SAM PLE SAM PLE L V D /P O R CPUCLK/ 2 4M H z (N o t to S ca le ) BRQ BRA CPU Document 38-16016 Rev. *C Page 30 of 62 [+] Feedback CY7C601xx CY7C602xx Low-Voltage Detect Control Table 41.Low-voltage Control Register (LVDCR) [0x1E3] [R/W] Bit # 7 Field 6 5 Reserved 4 PORLEV[1:0] 3 2 Reserved 1 0 VM[2:0] Read/Write – – R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register controls the configuration of the Power-on Reset/Low-voltage Detection circuit. This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register. Bit [7:6]: Reserved Bit [5:4]: PORLEV[1:0] This field controls the level below which the precision power-on-reset (PPOR) detector generates a reset. 0 0 = 2.7V Range (trip near 2.6V) 0 1 = 3V Range (trip near 2.9V) 1 0 = Reserved 1 1 = PPOR will not generate a reset, but values read from the Voltage Monitor Comparators Register (Table 42) give the internal PPOR comparator state with trip point set to the 3V range setting. Bit 3: Reserved Bit [2:0]: VM[2:0] This field controls the level below which the low-voltage-detect trips—possibly generating an interrupt and the level at which the Flash is enabled for operation. LVD Trip Point (V) VM[2:0] Min. Max. 000 2.69 2.72 2.7 001 2.90 2.94 2.92 010 3.00 3.04 3.02 011 3.10 3.15 3.13 100 Typical Reserved 101 Reserved 110 Reserved 111 Reserved POR Compare State Table 42.Voltage Monitor Comparators Register (VLTCMP) [0x1E4] [R] Bit # 7 6 5 Field 4 3 2 Reserved 1 0 LVD PPOR Read/Write – – – – – – R R Default 0 0 0 0 0 0 0 0 This read-only register allows reading the current state of the Low-voltage Detection and Precision-Power-On-Reset comparators. Bit [7:2]: Reserved Bit 1: LVD This bit is set to indicate that the low-voltage-detect comparator has tripped, indicating that the supply voltage has gone below the trip point set by VM[2:0] (See Table 41.) 0 = No low-voltage-detect event 1= A low-voltage-detect has tripped Bit 0: PPOR This bit is set to indicate that the precision-power-on-reset comparator has tripped, indicating that the supply voltage is below the trip point set by PORLEV[1:0]. 0 = No precision-power-on-reset event 1= A precision-power-on-reset event has occurred Note: This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register. Document 38-16016 Rev. *C Page 31 of 62 [+] Feedback CY7C601xx CY7C602xx ECO Trim Register Table 43.ECO (ECO_TR) [0x1EB] [R/W] Bit # Field 7 6 5 4 3 Sleep Duty Cycle [1:0] 2 1 0 Reserved Read/Write R/W R/W – – – – – – Default 0 0 0 0 0 0 0 0 This register controls the ratios (in numbers of 32 kHz clock periods) of “on” time versus “off” time for LVD and POR detection circuit. Bit [7:6]: Sleep Duty Cycle [1:0] 0 0 = 128 periods of the Internal 32 kHz Low-speed Oscillator 0 1 = 512 periods of the Internal 32 kHz Low-speed Oscillator 1 0 = 32 periods of the Internal 32 kHz Low-speed Oscillator 1 1 = 8 periods of the Internal 32 kHz Low-speed Oscillator Note: This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register. General Purpose I/O Ports Port Data Registers P0 Data Table 44.P0 Data Register (P0DATA)[0x00] [R/W] Bit # 7 6 5 4 3 2 1 0 Field P0.7 P0.6/TIO1 P0.5/TIO0 P0.4/INT2 P0.3/INT1 P0.2/INT0 P0.1/CLKOUT P0.0/CLKIN Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register contains the data for Port 0. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 0 pins. Bit 7: P0.7 Data Bit [6:5]: P0.6–P0.5 Data/TIO1 and TIO0 Beside their use as the P0.6–P0.5 GPIOs, these pins can also be used for the alternate functions as the Capture Timer input or Timer output pins (TIO1 and TIO0). To configure the P0.5 and P0.6 pins, refer to the P0.5/TIO0–P0.6/TIO1 Configuration Register (Table 52.) Bit [4:2]: P0.4–P0.2 Data/INT2–INT0 Beside their use as the P0.4–P0.2 GPIOs, these pins can also be used for the alternate functions as the Interrupt pins (INT0–INT2). To configure the P0.4–P0.2 pins, refer to the P0.2/INT0–P0.4/INT2 Configuration Register (Table 51) Bit 1: P0.1/CLKOUT Beside its use as the P0.1 GPIO, this pin can also be used for the alternate function as the CLK OUT pin. To configure the P0.1 pin, refer to the P0.1/CLKOUT Configuration Register (Table 50.) Bit 0: P0.0/CLKIN Beside its use as the P0.0 GPIO, this pin can also be used for the alternate function as the CLKIN pin. To configure the P0.0 pin, refer to the P0.0/CLKIN Configuration Register (Table 49.) Document 38-16016 Rev. *C Page 32 of 62 [+] Feedback CY7C601xx CY7C602xx P1 Data Table 45.P1 Data Register (P1DATA) [0x01] [R/W] Bit # 7 6 5 4 3 2 1 0 Field P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P1.3/SSEL P1.2 P1.1 P1.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register contains the data for Port 1. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 1 pins. Bit 7: P1.7 Data Bit [6:3]: P1.6–P1.3 Data/SPI Pins (SMISO, SMOSI, SCLK, SSEL) Beside their use as the P1.6–P1.3 GPIOs, these pins can also be used for the alternate function as the SPI interface pins. To configure the P1.6–P1.3 pins, refer to the P1.3–P1.6 Configuration Register (Table 57.) Bit [2:0]: P1.2–P1.0 P2 Data Table 46.P2 Data Register (P2DATA) [0x02] [R/W] Bit # 7 6 5 Field 4 3 2 1 P2.7–P2.2 0 P2.1–P2.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register contains the data for Port 2. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 2 pins. Bit [7:2]: P2 Data [7:2] Bit [1:0]: P2 Data [1:0] P3 Data Table 47.P3 Data Register (P3DATA) [0x03] [R/W] Bit # 7 6 5 Field 4 3 2 1 P3.7–P3.2 0 P3.1–P3.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register contains the data for Port 3. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 3 pins. Bit [7:2]: P3 Data [7:2] Bit [1:0]: P3 Data [1:0] P4 Data Table 48.P4 Data Register (P4DATA) [0x04] [R/W] Bit # 7 6 Field 5 4 3 2 Reserved 1 0 P4.3–P4.0 Read/Write – – – – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register contains the data for Port 4. Writing to this register sets the bit values to be output on output-enabled pins. Reading from this register returns the current state of the Port 2 pins. Bit [7:4]: Reserved Bit [3:0]: P4 Data [3:0] P4.3–P4.0 only exist in the CY7C601xx Document 38-16016 Rev. *C Page 33 of 62 [+] Feedback CY7C601xx CY7C602xx GPIO Port Configuration When clear, the output can sink up to 8 mA. All the GPIO configuration registers have common configuration controls. The following are the bit definitions of the GPIO configuration registers. By default all GPIOs are configured as inputs. In order to prevent the inputs from floating the pull up resistors are enabled. Firmware will need to configure each of the GPIOs prior to use. On the CY7C601xx, only the P3.7, P2.7, P0.1, and P0.0 have 50-mA sink drive capability. Other pins have 8-mA sink drive capability. On the CY7C602xx, only the P1.7–P1.3 have 50-mA sink drive capability. Other pins have 8-mA sink drive capability. Open Drain Int Enable When set, the Int Enable bit allows the GPIO to generate interrupts. Interrupt generate can occur regardless of whether the pin is configured for input or output. All interrupts are edge sensitive, however for any interrupt that is shared by multiple sources (i.e., Ports 2, 3, and 4) all inputs must be deasserted before a new interrupt can occur. When clear, the corresponding interrupt is disabled on the pin. It is possible to configure GPIOs as outputs, enable the interrupt on the pin and then to generate the interrupt by driving the appropriate pin state. This is useful in test and may find value in applications as well. When set, the output on the pin is determined by the Port Data Register. If the corresponding bit in the Port Data Register is set, the pin is in high impedance state. If the corresponding bit in the Port Data Register is clear, the pin is driven LOW. When clear, the output is driven LOW or HIGH. Pull Up Enable When set the pin has a 7K pull up to VDD. When clear, the pull- up is disabled. Output Enable When set, the output driver of the pin is enabled. Int Act Low When clear, the output driver of the pin is disabled. When clear, the corresponding interrupt is active HIGH. When set, the interrupt is active LOW. For P0.2–P0.4 Int act Low causes interrupts to be active on the rising edge. Int act Low set causes interrupts to be active on the falling edge. For pins with shared functions there are some special cases. TTL Thresh When set, the input has TTL threshold. When clear, the input has standard CMOS threshold. Important Note: The GPIOs default to CMOS threshold. User’s firmware needs to configure the threshold to TTL mode if necessary. P0.0(CLKIN) and P0.1(CLKOUT) can not be output enabled when the crystal oscillator is enabled. Output enables for these pins are overridden by XOSC Enable. SPI Use The P1.3(SSEL), P1.4(SCLK), P1.5(SMOSI) and P1.6(SMISO) pins can be used for their dedicated functions or for GPIO. To enable the pin for GPIO, clear the corresponding SPI Use bit. The SPI function controls the output enable for its dedicated function pins when their GPIO enable bit is clear. High Sink When set, the output can sink up to 50 mA. Figure 10. GPIO Block Diagram VCC VREG 3.3V Drive Pull-Up Enable Output Enable VREG VCC RUP Open Drain Port Data Data Out GPIO PIN High Sink VREG GND VCC GND Data In TTL Threshold Document 38-16016 Rev. *C Page 34 of 62 [+] Feedback CY7C601xx CY7C602xx P0.0/CLKIN Configuration Table 49.P0.0/CLKIN Configuration (P00CR) [0x05] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable Read/Write – R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This pin is shared between the P0.0 GPIO use and the CLKIN pin for the external crystal oscillator. When the external oscillator is enabled the settings of this register are ignored. The alternate function of the pin as the CLKIN is only available in the CY7C601xx. When the external oscillator is enabled (the XOSC Enable bit of the CLKIOCR Register is set—Table 34), the GPIO function of the pin is disabled. The 50-mA sink drive capability is only available in the CY7C601xx. In the CY7C602xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. If this pin is used as a General Purpose output it will draw current. This pin should be configured as an input to reduce current draw. P0.1/CLKOUT Configuration Table 50.P0.1/CLKOUT Configuration (P01CR) [0x06] R/W] Bit # 7 6 5 4 3 2 1 0 Field CLK Output Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This pin is shared between the P0.1 GPIO use and the CLKOUT pin for the external crystal oscillator. When the external oscillator is enabled the settings of this register are ignored. When CLK output is set, the internally selected clock is sent out onto P0.1CLKOUT pin. The alternate function of the pin as the CLKOUT is only available in the CY7C601xx. When the external oscillator is enabled (the XOSC Enable bit of the CLKIOCR Register is set—Table 34), the GPIO function of the pin is disabled. The 50-mA sink drive capability is only available in the CY7C601xx. In the CY7C602xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. If this pin is used as a General Purpose output it will draw current. This pin should be configured as an input to reduce current draw Bit 7: CLK Output 0 = The clock output is disabled 1 = The clock selected by the CLK Select field (Bit [1:0] of the CLKIOCR Register—Table 34) is driven out to the pin Document 38-16016 Rev. *C Page 35 of 62 [+] Feedback CY7C601xx CY7C602xx P0.2/INT0–P0.4/INT2 Configuration Table 51.P0.2/INT0–P0.4/INT2 Configuration (P02CR–P04CR) [0x07–0x09] [R/W] Bit # 7 Field 6 Reserved 5 4 3 2 1 0 Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable Read/Write – – R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 These registers control the operation of pins P0.2–P0.4 respectively. These pins are shared between the P0.2–P0.4 GPIOs and the INT0–INT2. The INT0–INT2 interrupts are different than all the other GPIO interrupts. These pins are connected directly to the interrupt controller to provide three edge-sensitive interrupts with independent interrupt vectors. These interrupts occur on a rising edge when Int act Low is clear and on a falling edge when Int act Low is set. These pins are enabled as interrupt sources in the interrupt controller registers (Table 87 and Table 85). To use these pins as interrupt inputs configure them as inputs by clearing the corresponding Output Enable. If the INT0–INT2 pins are configured as outputs with interrupts enabled, firmware can generate an interrupt by writing the appropriate value to the P0.2, P0.3, and P0.4 data bits in the P0 Data Register. Regardless of whether the pins are used as Interrupt or GPIO pins the Int Enable, Int act Low, TTL Threshold, Open Drain, and Pull-up Enable bits control the behavior of the pin. The P0.2/INT0–P0.4/INT2 pins are individually configured with the P02CR (0x07), P03CR (0x08), and P04CR (0x09) respectively. Note: Changing the state of the Int Act Low bit can cause an unintentional interrupt to be generated. When configuring these interrupt sources, it is best to follow the following procedure: 1. Disable interrupt source 2. Configure interrupt source 3. Clear any pending interrupts from the source 4. Enable interrupt source P0.5/TIO0–P0.6/TIO1 Configuration Table 52.P0.5/TIO0–P0.6/TIO1 Configuration (P05CR–P06CR) [0x0A–0x0B] [R/W] Bit # 7 6 5 4 3 2 1 0 Field TIO Output Int Enable Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable Read/Write R/W R/W R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 These registers control the operation of pins P0.5 through P0.6, respectively. P0.5 and P0.6 are shared with TIO0 and TIO1, respectively. To use these pins as Capture Timer inputs, configure them as inputs by clearing the corresponding Output Enable. To use TIO0 and TIO1 as Timer outputs, set the TIOx Output and Output Enable bits. If these pins are configured as outputs and the TIO Output bit is clear, firmware can control the TIO0 and TIO1 inputs by writing the value to the P0.5 and P0.6 data bits in the P0 Data Register. Regardless of whether either pin is used as a TIO or GPIO pin the Int Enable, Int act Low, TTL Threshold, Open Drain, and Pullup Enable control the behavior of the pin. TIO0(P0.5) when enabled outputs a positive pulse from the 1024-µs interval timer. This is the same signal that is used internally to generate the 1024-µs timer interrupt. This signal is not gated by the interrupt enable state. TIO1(P0.6) when enabled outputs a positive pulse from the programmable interval timer. This is the same signal that is used internally to generate the programmable timer interval interrupt. This signal is not gated by the interrupt enable state. The P0.5/TIO0 and P0.6/TIO1 pins are individually configured with the P05CR (0x0A) and P06CR (0x0B), respectively P0.7 Configuration Table 53.P0.7 Configuration (P07CR) [0x0C] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable Read/Write – R/W R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register controls the operation of pin P0.7 Document 38-16016 Rev. *C Page 36 of 62 [+] Feedback CY7C601xx CY7C602xx P1.0 Configuration Table 54.P1.0 Configuration (P10CR) [0x0D] [R/W] Bit # 7 6 5 Field Reserved Int Enable Int Act Low 4 3 Read/Write R/W R/W R/W – – Default 0 0 0 0 0 2 1 0 P1.0 and P1.1 Pull Up Enable Output Enable – – R/W 0 0 0 Reserved This register controls the operation of the P1.0 pin. Bit1: P1.0 and P1.1 Pull Up Enable 0 = Disable the P1.0 and P1.1 pull up resistors 1 = Enable the internal pull up resistors for both the P1.0 and P1.1. Each of the P1.0 and P1.1 pins is pulled up with RUP1 (see DC Characteristics on page 54) Note: There is no 2-mA sourcing capability on this pin. The pin can only sink 5 mA at VOL3 (see DC Characteristics on page 54) The P1.0 is an open drain only output. It can actively drive a signal low, but cannot actively drive a signal high. P1.1 Configuration Table 55.P1.1 Configuration (P11CR) [0x0E] [R/W] Bit # 7 6 5 Field Reserved Int Enable Int Act Low 4 3 Read/Write – R/W R/W – – Default 0 0 0 0 0 Reserved 2 1 0 Open Drain Reserved Output Enable R/W – R/W 0 0 0 This register controls the operation of the P1.1 pin. The pull up resistor on this pin is enabled by the P10CR Register Note: There is no 2-mA sourcing capability on this pin. The pin can only sink 5 mA at VOL3 (see DC Characteristics on page 54) P1.2 Configuration Table 56.P1.2 Configuration (P12CR) [0x0F] [R/W] Bit # 7 6 5 4 3 2 1 0 Field CLK Output Int Enable Int Act Low TTL Threshold Reserved Open Drain Pull-up Enable Output Enable Read/Write R/W R/W R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register controls the operation of the P1.2 Bit 7: CLK Output 0 = The internally selected clock is not sent out onto P1.2 pin 1 = This CLK Output is used to observe connected external crystal oscillator clock connected in CY7C601xx. When CLK Output is set, the internally selected clock is sent out onto P1.2 pin. Document 38-16016 Rev. *C Page 37 of 62 [+] Feedback CY7C601xx CY7C602xx P1.3 Configuration (SSEL) Table 57.P1.3 Configuration (P13CR) [0x10] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low Reserved High Sink Open Drain Pull Up Enable Output Enable Read/Write – R/W R/W – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register controls the operation of the P1.3 pin. The P1.3 GPIO’s threshold is always set to TTL. When the SPI hardware is enabled, the output enable and output state of the pin is controlled by the SPI circuitry. When the SPI hardware is disabled, the pin is controlled by the Output Enable bit and the corresponding bit in the P1 data register. Regardless of whether the pin is used as an SPI or GPIO pin the Int Enable, Int act Low, High Sink, Open Drain, and Pull Up Enable control the behavior of the pin. The 50-mA sink drive capability is only available in the CY7C602xx. In the CY7C601xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. P1.4–P1.6 Configuration (SCLK, SMOSI, SMISO) Table 58.P1.4–P1.6 Configuration (P14CR–P16CR) [0x11–0x13] [R/W] Bit # 7 6 5 4 3 2 1 0 Field SPI Use Int Enable Int Act Low Reserved High Sink Open Drain Pull Up Enable Output Enable Read/Write R/W R/W R/W – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 These registers control the operation of pins P1.4–P1.6, respectively. The P1.4–P1.6 GPIO’s threshold is always set to TTL. When the SPI hardware is enabled, pins that are configured as SPI Use have their output enable and output state controlled by the SPI circuitry. When the SPI hardware is disabled or a pin has its SPI Use bit clear, the pin is controlled by the Output Enable bit and the corresponding bit in the P1 data register. Regardless of whether any pin is used as an SPI or GPIO pin the Int Enable, Int act Low, High Sink, Open Drain, and Pull-up Enable control the behavior of the pin. The 50-mA sink drive capability is only available in the CY7C602xx. In the CY7C601xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. Bit 7: SPI Use 0 = Disable the SPI alternate function. The pin is used as a GPIO 1 = Enable the SPI function. The SPI circuitry controls the output of the pin Important Note for Comm Modes 01 or 10 (SPI Master or SPI Slave, see Table 64): When configured for SPI (SPI Use = 1 and Comm Modes [1:0] = SPI Master or SPI Slave mode), the input/output direction of pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input. P1.7 Configuration Table 59. P1.7 Configuration (P17CR) [0x14] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low Reserved High Sink Open Drain Pull Up Enable Output Enable Read/Write – R/W R/W – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register controls the operation of pin P1.7. The 50-mA sink drive capability is only available in the CY7C602xx. In the CY7C601xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. The P1.7 GPIO’s threshold is always set to TTL. Document 38-16016 Rev. *C Page 38 of 62 [+] Feedback CY7C601xx CY7C602xx P2 Configuration Table 60.P2 Configuration (P2CR) [0x15] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull Up Enable Output Enable Read/Write – R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 In CY7C602xx this register controls the operation of pins P2.0–P2.1. In the CY7C601xx, this register controls the operation of pins P2.0–P2.7. The 50-mA sink drive capability is only available on pin P2.7 and only on the CY7C601xx. In the CY7C602xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. P3 Configuration Table 61.P3 Configuration (P3CR) [0x16] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull Up Enable Output Enable Read/Write – R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 In CY7C602xx this register controls the operation of pins P3.0–P3.1. In the CY7C601xx, this register controls the operation of pins P3.0–P3.7. The 50-mA sink drive capability is only available on pin P3.7 and only on the CY7C601xx. In the CY7C602xx, only 8-mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. P4 Configuration Table 62.P4 Configuration (P4CR) [0x17] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull Up Enable Output Enable Read/Write – R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 This register exists only in the CY7C601xx. This register controls the operation of pins P4.0–P4.3. Document 38-16016 Rev. *C Page 39 of 62 [+] Feedback CY7C601xx CY7C602xx Serial Peripheral Interface (SPI) The SPI Master/Slave Interface core logic runs on the SPI clock domain. The SPI clock is a divider off of the CPUCLK when in Master Mode. SPI is a four-pin serial interface comprised of a clock, an enable, and two data pins. Figure 11. SPI Block Diagram Register Block SCK Speed Sel SCK Clock Generation Master/Slave Sel SCK Clock Select SCK Polarity SCK_OE SCK Clock Phase/Polarity Select SCK Phase SCK SCK Little Endian Sel LE_SEL GPIO Block SS_N SS_N SPI State Machine SS_N_OE SS_N Data (8 bit) Load MISO_OE Output Shift Buffer Empty Master/Slave Set MISO/MOSI Crossbar MISO SCK LE_SEL Shift Buffer MOSI_OE MOSI Data (8 bit) Input Shift Buffer Load Full Sclk Output Enable Slave Select Output Enable Master IN, Slave Out OE Master Out, Slave In, OE Document 38-16016 Rev. *C SCK_OE SS_N_OE MISO_OE MOSI_OE Page 40 of 62 [+] Feedback CY7C601xx CY7C602xx SPI Data Register Table 63.SPI Data Register (SPIDATA) [0x3C] [R/W] Bit # 7 6 5 4 Field 3 2 1 0 SPIData[7:0] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 When read, this register returns the contents of the receive buffer. When written, it loads the transmit holding register. Bit [7:0]: SPI Data [7:0] When an interrupt occurs to indicate to firmware that an byte of receive data is available, or the transmitter holding register is empty, firmware has 7 SPI clocks to manage the buffers—to empty the receiver buffer, or to refill the transmit holding register. Failure to meet this timing requirement will result in incorrect data transfer. SPI Configure Register Table 64.SPI Configure Register (SPICR) [0x3D] [R/W] Bit # 7 6 Field Swap LSB First 5 Read/Write R/W R/W R/W Default 0 0 0 4 3 2 CPOL CPHA R/W R/W R/W R/W R/W 0 0 0 0 0 Comm Mode 1 0 SCLK Select Bit 7: Swap 0 = Swap function disabled 1 = The SPI block swaps its use of SMOSI and SMISO. Among other things, this can be useful in implementing single wire SPIlike communications. Bit 6: LSB First 0 = The SPI transmits and receives the MSB (Most Significant Bit) first 1 = The SPI transmits and receives the LSB (Least Significant Bit) first. Bit [5:4]: Comm Mode [1:0] 0 0: All SPI communication disabled 0 1: SPI master mode 1 0: SPI slave mode 1 1: Reserved Bit 3: CPOL This bit controls the SPI clock (SCLK) idle polarity. 0 = SCLK idles low 1 = SCLK idles high Bit 2: CPHA The Clock Phase bit controls the phase of the clock on which data is sampled. Table 65 below shows the timing for the various combinations of LSB First, CPOL, and CPHA. Bit [1:0]: SCLK Select This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base CPUCLK Important Note for Comm Modes 01b or 10b (SPI Master or SPI Slave): When configured for SPI, (SPI Use = 1 – Table 58), the input/output direction of pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input. Document 38-16016 Rev. *C Page 41 of 62 [+] Feedback CY7C601xx CY7C602xx Table 65.SPI Mode Timing vs. LSB First, CPOL and CPHA LSB First 0 CPHA CPOL 0 Diagram 0 SCLK SSEL D AT A 0 0 X MSB B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 X LSB 1 SC LK SSEL DAT A 0 1 X MSB B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 X LSB 0 SC LK SSEL DAT A 0 1 X MSB B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 LS B X X MS B B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 LSB X 1 SC L K SSEL D AT A 1 0 0 SCLK SSEL DAT A 1 0 X LSB B it 2 B it 3 B it 4 B it 5 B it 6 B it 7 MS B X X LSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 MSB X 1 SCLK SSEL DAT A 1 1 0 SCLK SSEL DAT A 1 1 X LSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 MSB X X LSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 MSB X 1 SC LK SSEL DAT A Document 38-16016 Rev. *C Page 42 of 62 [+] Feedback CY7C601xx CY7C602xx clock. The 16-bit free-running counter is used as the time-base for timer captures and can also be used as a general timebase by software. Table 66.SPI SCLK Frequency SCLK CPUCLK Select Divisor SCLK Frequency when CPUCLK = 12 MHz 00 6 2 MHz Registers 01 12 1 MHz Free-running Counter The 16 bit free-running counter is clocked by the Timer Capture Clock (TCAPCLK). It can be read in software for use as a general-purpose time base. When the low-order byte is read, the high-order byte is registered. Reading the high-order byte reads this register allowing the CPU to read the 16-bit value atomically (loads all bits at one time). The free-running timer generates an interrupt at 1024-µs rate when clocked by a 4 MHz source. It can also generate an interrupt when the free-running counter overflow occurs—every 16.384 ms (with a 4 MHz source). This allows extending the length of the timer in software. 10 48 250 kHz 11 96 125 kHz SPI Interface Pins The SPI interface uses the P1.3–P1.6 pins. These pins are configured using the P1.3 and P1.4–P1.6 Configuration. Timer Registers All timer functions of the enCoRe II LV are provided by a single timer block. The timer block is asynchronous from the CPU Figure 12. 16-bit Free Running Counter Block Diagram Overflow Interrupt/W rap Interrupt Tim er Capture C lock 16-bit Free Running Counter 1024-µs Tim er Interrupt Table 67.Free-running Timer Low-order Byte (FRTMRL) [0x20] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Free Running Timer [7:0] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit [7:0]: Free-running Timer [7:0] This register holds the low-order byte of the 16-bit free-running timer. Reading this register causes the high-order byte to be moved into a holding register allowing an automatic read of all 16 bits simultaneously. For reads, the actual read occurs in the cycle when the low order is read. For writes the actual time the write occurs is the cycle when the high order is written. When reading the Free-running Timer, the low-order byte should be read first and the high-order second. When writing, the loworder byte should be written first then the high-order byte. Document 38-16016 Rev. *C Page 43 of 62 [+] Feedback CY7C601xx CY7C602xx Table 68.Free-running Timer High-order Byte (FRTMRH) [0x21] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Free Running Timer [15:8] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit [7:0]: Free-running Timer [15:8] When reading the Free-running Timer, the low-order byte should be read first and the high-order second. When writing, the loworder byte should be written first then the high-order byte. configured in this way, the capture 1 resisters hold the high order byte of the 16-bit timer capture value. Each of the four capture registers can be programmed to generate an interrupt when it is loaded. Time Capture enCoRe II LV has two 8-bit captures. Each capture has separate register for the rising and falling time. The two 8-bit captures can be configured as a single 16-bit capture. When Figure 13. Time Capture Block Diagram Programmable Interval Timer External Clock Internal 24-MHz Oscillator Timer Capture Clock Output (4-MHz Default) Source Control and Configuration Internal Low Power 32-KHz Oscillator 16-bit Free Running Counter Table 69.Timer Configuration (TMRCR) [0x2A] [R/W] Bit # 7 Field First Edge Hold 6 5 4 Read/Write R/W R/W R/W R/W R/W – – – Default 0 0 0 0 0 0 0 0 8-bit Capture Prescale [2:0] 3 2 Cap0 16-bit Enable 1 0 Reserved Bit 7: First Edge Hold The First Edge Hold function applies to all four-capture timers. 0 = The time of the most recent edge is held in the Capture Timer Data Register. If multiple edges have occurred since reading the capture timer, the time for the most recent one will be read. 1 = The time of the first occurrence of an edge is held in the Capture Timer Data Register until the data is read. Subsequent edges are ignored until the Capture Timer Data Register is read. Bit [6:4]: 8-bit Capture Prescale [2:0] This field controls which 8 bits of the 16 Free Running Timer are captured when in bit mode. 0 0 0 = capture timer[7:0] 0 0 1 = capture timer[8:1] 0 1 0 = capture timer[9:2] 0 1 1 = capture timer[10:3] 1 0 0 = capture timer[11:4] 1 0 1 = capture timer[12:5] 1 1 0 = capture timer[13:6] 1 1 1 = capture timer[14:7] Bit 3: Cap0 16-bit Enable 0 = Capture 0 16-bit mode is disabled 1 = Capture 0 16-bit mode is enabled. Capture 1 is disabled and the Capture 1 rising and falling registers are used as an extension to the Capture 0 registers—extending them to 16 bits. Bit [2:0]: Reserved Document 38-16016 Rev. *C Page 44 of 62 [+] Feedback CY7C601xx CY7C602xx Table 70.Capture Interrupt Enable (TCAPINTE) [0x2B] [R/W] Bit # 7 6 Field 5 4 Reserved 3 2 1 0 Cap1 Fall Enable Cap1 Rise Enable Cap0 Fall Enable Cap0 Rise Enable Read/Write – – – – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 4 3 2 1 0 Bit [7:4]: Reserved Bit 3: Cap1 Fall Enable 0 = Disable the capture 1 falling edge interrupt 1 = Enable the capture 1 falling edge interrupt Bit 2: Cap1 Rise Enable 0 = Disable the capture 1 rising edge interrupt 1 = Enable the capture 1 rising edge interrupt Bit 1: Cap0 Fall Enable 0 = Disable the capture 0 falling edge interrupt 1 = Enable the capture 0 falling edge interrupt Bit 0: Cap0 Rise Enable 0 = Disable the capture 0 rising edge interrupt 1 = Enable the capture 0 rising edge interrupt Table 71.Timer Capture 0 Rising (TCAP0R) [0x22] [R/W] Bit # 7 6 5 Field Capture 0 Rising [7:0] Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit [7:0]: Capture 0 Rising [7:0] This register holds the value of the Free-running Timer when the last rising edge occurred on the TCAP0 input. When Capture 0 is in 8-bit mode, the bits that are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When Capture 0 is in 16-bit mode this register holds the lower order 8 bits of the 16-bit timer. Table 72.Timer Capture 1 Rising (TCAP1R) [0x23] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Capture 1 Rising [7:0] Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit [7:0]: Capture 1 Rising [7:0] This register holds the value of the Free-running Timer when the last rising edge occurred on the TCAP1 input. The bits that are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When Capture 0 is in 16-bit mode this register holds the high-order 8 bits of the 16-bit timer from the last Capture 0 rising edge. When Capture 0 is in 16-bit mode this register will be loaded with the high-order 8 bits of the 16-bit timer on TCAP0 rising edge. Table 73.Timer Capture 0 Falling (TCAP0F) [0x24] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Capture 0 Falling [7:0] Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit [7:0]: Capture 0 Falling [7:0] This register holds the value of the Free-running Timer when the last falling edge occurred on the TCAP0 input. When Capture 0 is in 8-bit mode, the bits that are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When Capture 0 is in 16-bit mode this register holds the lower order 8 bits of the 16-bit timer. Document 38-16016 Rev. *C Page 45 of 62 [+] Feedback CY7C601xx CY7C602xx Table 74.Timer Capture 1 Falling (TCAP1F) [0x25] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Capture 1 Falling [7:0] Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit [7:0]: Capture 1 Falling [7:0] This register holds the value of the Free-running Timer when the last falling edge occurred on the TCAP1 input. The bits that are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When capture 0 is in 16-bit mode this register holds the high-order 8 bits of the 16-bit timer from the last Capture 0 falling edge. When Capture 0 is in 16-bit mode this register will be loaded with high-order 8 bits of the 16-bit timer on TCAP0 falling edge. ‘ Table 75.Capture Interrupt Status (TCAPINTS) [0x2C] [R/W] Bit # 7 6 Field 5 4 Reserved 3 2 1 0 Cap1 Fall Active Cap1 Rise Active Cap0 Fall Active Cap0 Rise Active Read/Write – – – – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 These four bits contains the status bits for the four timer captures for the four timer block capture interrupt sources. Writing any of these bits with 1 clears that interrupt. Bit [7:4]: Reserved Bit 3: Cap1 Fall Active 0 = No event 1 = A falling edge has occurred on Cap1 Bit 2: Cap1 Rise Active 0 = No event 1 = A rising edge has occurred on Cap1 Bit 1: Cap0 Fall Active 0 = No event 1 = A falling edge has occurred on Cap0 Bit 0: Cap0 Rise Active 0 = No event 1 = A rising edge has occurred on Cap0 Note: The interrupt status bits must be cleared by firmware to enable subsequent interrupts. This is achieved by writing a ‘1’ to the corresponding Interrupt status bit. Programmable Interval Timer Table 76.Programmable Interval Timer Low (PITMRL) [0x26] [R] Bit # 7 6 5 Field 4 3 2 1 0 Prog Interval Timer [7:0] Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit [7:0]: Prog Interval Timer [7:0] This register holds the low order-byte of the 12-bit programmable interval timer. Reading this register causes the high-order byte to be moved into a holding register allowing an automatic read of all 12 bits simultaneously. Table 77.Programmable Interval Timer High (PITMRH) [0x27] [R] Bit # 7 6 Field 5 4 3 Reserved 2 1 0 Prog Interval Timer [11:8] Read/Write -- -- -- -- R R R R Default 0 0 0 0 0 0 0 0 Bit [7:4]: Reserved Bit [3:0]: Prog Internal Timer [11:8] This register holds the high order nibble of the 12-bit programmable interval timer. Reading this register returns the high order nibble of the 12-bit timer at the instant that the low order byte was last read. Document 38-16016 Rev. *C Page 46 of 62 [+] Feedback CY7C601xx CY7C602xx Table 78.Programmable Interval Reload Low (PIRL) [0x28] [R/W] Bit # 7 6 5 Field 4 3 2 1 0 Prog Interval [7:0] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit [7:0]: Prog Interval [7:0] This register holds the lower 8 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher nibble. Table 79.Programmable Interval Reload High (PIRH) [0x29] [R/W] Bit # 7 6 Field 5 4 3 Reserved 2 1 0 Prog Interval[11:8] Read/Write -- -- -- -- R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit [7:4]: Reserved Bit [3:0]: Prog Interval [11:8] This register holds the higher 4 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher nibble. Figure 14. Timer Functional Timing Diagram clk_captimer 16-bit free running counter clk_sys capture0 cap0_rise cap0_fall capture1 cap1_rise cap1_fall cap0_rise_reg cap0_fall_reg cap1_rise_reg cap1_fall_reg Timing diagrams when cap0 is in 8 bit mode cap1_rise_reg cap1_fall_reg Timing diagrams when cap0 is in 16 bit mode Document 38-16016 Rev. *C Page 47 of 62 [+] Feedback CY7C601xx CY7C602xx Figure 15. 16-bit Free Running Counter Loading Timing Diagram clk_sys write valid addr write data FRT reload ready Clk Timer 12b Prog Timer 12b reload interrupt 12-bit programmable timer load timing Capture timer clk 16b free running counter load 16b free running counter 00A0 00A1 00A2 00A3 00A4 00A5 00A6 00A7 00A8 00A9 00AB 00AC 00AD 00AE 00AF 00B0 00B1 00B2 ACBE ACBF ACC0 16-bit free running counter loading timing Figure 16. Memory Mapped Registers Read/Write Timing Diagram clk_sys rd_wrn Valid Addr rdata wdata Memory mapped registers Read/Write timing diagram Document 38-16016 Rev. *C Page 48 of 62 [+] Feedback CY7C601xx CY7C602xx Interrupt Controller Table 80.Interrupt Priorities, Address, Name (continued) The interrupt controller and its associated registers allow the user’s code to respond to an interrupt from almost every functional block in the enCoRe II LV devices. The registers associated with the interrupt controller allow to be disabled either globally or individually. The registers also provide a mechanism by which a user may clear all pending and posted interrupts, or clear individual posted or pending interrupts. Interrupt Priority Interrupt Address 16 0040h 17 0044h 16-bit Free Running Timer Wrap 18 0048h INT2 19 004Ch Reserved Table 80 lists all interrupts and the priorities that are available in the enCoRe II LV devices. 20 0050h GPIO Port 2 21 0054h GPIO Port 3 Table 80.Interrupt Priorities, Address, Name 22 0058h GPIO Port 4 23 005Ch Reserved 24 0060h Reserved 25 0064h Sleep Timer Name Timer Capture 1 Interrupt Priority Interrupt Address 0 0000h Reset 1 0004h POR/LVD 2 0008h INT0 Architectural Description 3 000Ch SPI Transmitter Empty 4 0010h SPI Receiver Full 5 0014h GPIO Port 0 An interrupt is posted when its interrupt conditions occur. This results in the flip-flop in Figure 17 clocking in a ‘1’. The interrupt will remain posted until the interrupt is taken or until it is cleared by writing to the appropriate INT_CLRx register. 6 0018h GPIO Port 1 7 001Ch INT1 8 0020h Reserved Name A posted interrupt is not pending unless it is enabled by setting its interrupt mask bit (in the appropriate INT_MSKx register). All pending interrupts are processed by the Priority Encoder to determine the highest priority interrupt which will be taken by the M8C if the Global Interrupt Enable bit is set in the CPU_F register. 9 0024h Reserved 10 0028h Reserved 11 002Ch Reserved 12 0030h Reserved 13 0034h 1-mS Interval timer 14 0038h Programmable Interval Timer 15 003Ch Timer Capture 0 Disabling an interrupt by clearing its interrupt mask bit (in the INT_MSKx register) does not clear a posted interrupt, nor does it prevent an interrupt from being posted. It simply prevents a posted interrupt from becoming pending. Nested interrupts can be accomplished by reenabling interrupts inside an interrupt service routine. To do this, set the IE bit in the Flag Register. A block diagram of the enCoRe II LV Interrupt Controller is shown in Figure 17. Figure 17. Interrupt Controller Block Diagram Priority Encoder Interrupt Taken or Interrupt Vector INT_CLRx Write Posted Interrupt Pending Interrupt D ... ... R 1 Interrupt Request Q Interrupt Source (Timer, GPIO, etc.) M8C Core CPU_F[0] GIE INT_MSKx Mask Bit Setting Document 38-16016 Rev. *C Page 49 of 62 [+] Feedback CY7C601xx CY7C602xx 5. The ISR executes. Note that interrupts are disabled since GIE = 0. In the ISR, interrupts can be re-enabled if desired by setting GIE = 1 (care must be taken to avoid stack overflow). 6. The ISR ends with a RETI instruction which restores the Program Counter and Flag registers (CPU_PC and CPU_F). The restored Flag register re-enables interrupts, since GIE = 1 again. 7. Execution resumes at the next instruction, after the one that occurred before the interrupt. However, if there are more pending interrupts, the subsequent interrupts will be processed before the next normal program instruction. Interrupt Processing The sequence of events that occur during interrupt processing is as follows: 1. An interrupt becomes active, either because: a. The interrupt condition occurs (e.g., a timer expires). b. A previously posted interrupt is enabled through an update of an interrupt mask register. c. An interrupt is pending and GIE is set from 0 to 1 in the CPU Flag register. 2. The current executing instruction finishes. 3. The internal interrupt is dispatched, taking 13 cycles. During this time, the following actions occur: Interrupt Latency a. The MSB and LSB of Program Counter and Flag registers (CPU_PC and CPU_F) are stored onto the program stack by an automatic CALL instruction (13 cycles) generated during the interrupt acknowledge process. b. The PCH, PCL, and Flag register (CPU_F) are stored onto the program stack (in that order) by an automatic CALL instruction (13 cycles) generated during the interrupt acknowledge process. c. The CPU_F register is then cleared. Since this clears the GIE bit to 0, additional interrupts are temporarily disabled. d. The PCH (PC[15:8]) is cleared to zero. e. The interrupt vector is read from the interrupt controller and its value placed into PCL (PC[7:0]). This sets the program counter to point to the appropriate address in the interrupt table (e.g., 0004h for the POR/LVD interrupt). 4. Program execution vectors to the interrupt table. Typically, a LJMP instruction in the interrupt table sends execution to the user's Interrupt Service Routine (ISR) for this interrup0t. The time between the assertion of an enabled interrupt and the start of its ISR can be calculated from the following equation. Latency = Time for current instruction to finish + Time for internal interrupt routine to execute + Time for LJMP instruction in interrupt table to execute. For example, if the 5-cycle JMP instruction is executing when an interrupt becomes active, the total number of CPU clock cycles before the ISR begins would be as follows: (1 to 5 cycles for JMP to finish) + (13 cycles for interrupt routine) + (7 cycles for LJMP) = 21 to 25 cycles. In the example above, at 12 MHz, 25 clock cycles take 2.08 µs. Interrupt Registers Interrupt Clear Register The Interrupt Clear Registers (INT_CLRx) are used to enable the individual interrupt sources’ ability to clear posted interrupts. When an INT_CLRx register is read, any bits that are set indicates an interrupt has been posted for that hardware resource. Therefore, reading these registers gives the user the ability to determine all posted interrupts. Table 81. Interrupt Clear 0 (INT_CLR0) [0xDA] [R/W] Bit # 7 6 5 4 3 2 1 0 Field GPIO Port 1 Sleep Timer INT1 GPIO Port 0 SPI Receive SPI Transmit INT0 POR/LVD Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 When reading this register, 0 = There’s no posted interrupt for the corresponding hardware 1 = Posted interrupt for the corresponding hardware present Writing a ‘0’ to the bits will clear the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT (Bit 7 of the INT_MSK3 Register) will post the corresponding hardware interrupt. Document 38-16016 Rev. *C Page 50 of 62 [+] Feedback CY7C601xx CY7C602xx Table 82. Interrupt Clear 1 (INT_CLR1) [0xDB] [R/W] Bit # 7 6 5 Field TCAP0 Prog Interval Timer 1-ms Programmable Interrupt 4 3 Read/Write R/W R/W R/W – – Default 0 0 0 0 0 2 1 0 – – – 0 0 0 Reserved When reading this register, 0 = There’s no posted interrupt for the corresponding hardware 1 = Posted interrupt for the corresponding hardware present Writing a ‘0’ to the bits will clear the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT (Bit 7 of the INT_MSK3 Register) will post the corresponding hardware interrupt. Table 83.Interrupt Clear 2 (INT_CLR2) [0xDC] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved GPIO Port 4 GPIO Port 3 GPIO Port 2 Reserved INT2 16-bit Counter Wrap TCAP1 Read/Write – R/W R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 When reading this register, 0 = There’s no posted interrupt for the corresponding hardware 1 = Posted interrupt for the corresponding hardware present Writing a ‘0’ to the bits will clear the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT (Bit 7 of the INT_MSK3 Register) will post the corresponding hardware interrupt. The Enable Software Interrupt (ENSWINT) bit in INT_MSK3[7] determines the way an individual bit value written to an INT_CLRx register is interpreted. When is cleared, writing 1's to an INT_CLRx register has no effect. However, writing 0's to an INT_CLRx register, when ENSWINT is cleared, will cause the corresponding interrupt to clear. If the ENSWINT bit is set, any 0's written to the INT_CLRx registers are ignored. However, 1's written to an INT_CLRx register, while ENSWINT is set, will cause an interrupt to post for the corresponding interrupt. Interrupt Mask Registers The Interrupt Mask Registers (INT_MSKx) are used to enable the individual interrupt sources’ ability to create pending interrupts. There are four Interrupt Mask Registers (INT_MSK0, INT_MSK1, INT_MSK2, and INT_MSK3) which may be referred to in general as INT_MSKx. If cleared, each bit in an INT_MSKx register prevents a posted interrupt from becoming a pending interrupt (input to the priority encoder). However, an interrupt can still post even if its mask bit is zero. All INT_MSKx bits are independent of all other INT_MSKx bits. Software interrupts can aid in debugging interrupt service routines by eliminating the need to create system level interactions that are sometimes necessary to create a hardwareonly interrupt. If an INT_MSKx bit is set, the interrupt source associated with that mask bit may generate an interrupt that will become a pending interrupt. Table 84.Interrupt Mask 3 (INT_MSK3) [0xDE] [R/W] Bit # 7 Field ENSWINT 6 5 4 Read/Write R – – – Default 0 0 0 0 3 2 1 0 – – – – 0 0 0 0 Reserved Bit 7: Enable Software Interrupt (ENSWINT) 0= Disable. Writing 0's to an INT_CLRx register, when ENSWINT is cleared, will cause the corresponding interrupt to clear. 1= Enable. Writing 1's to an INT_CLRx register, when ENSWINT is set, will cause the corresponding interrupt to post. Bit [6:0]: Reserved Document 38-16016 Rev. *C Page 51 of 62 [+] Feedback CY7C601xx CY7C602xx Table 85.Interrupt Mask 2 (INT_MSK2) [0xDF] [R/W] Bit # 7 6 5 4 3 2 1 0 Field Reserved GPIO Port 4 Int Enable GPIO Port 3 Int Enable GPIO Port 2 Int Enable Reserved INT2 Int Enable 16-bit Counter Wrap Int Enable TCAP1 Int Enable Read/Write – R/W R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 4 3 2 1 0 Bit 7: Reserved Bit 6: GPIO Port 4 Interrupt Enable 0 = Mask GPIO Port 4 interrupt 1 = Unmask GPIO Port 4 interrupt Bit 5: GPIO Port 3 Interrupt Enable 0 = Mask GPIO Port 3 interrupt 1 = Unmask GPIO Port 3 interrupt Bit 4: GPIO Port 2 Interrupt Enable 0 = Mask GPIO Port 2 interrupt 1 = Unmask GPIO Port 2 interrupt Bit 3: Reserved Bit 2: INT2 Interrupt Enable 0 = Mask INT2 interrupt 1 = Unmask INT2 interrupt Bit 1: 16-bit Counter Wrap Interrupt Enable 0 = Mask 16-bit Counter Wrap interrupt 1 = Unmask 16-bit Counter Wrap interrupt Bit 0: TCAP1 Interrupt Enable 0 = Mask TCAP1 interrupt 1 = Unmask TCAP1 interrupt Table 86.Interrupt Mask 1 (INT_MSK1) [0xE1] [R/W] Bit # 7 6 5 Field TCAP0 Int Enable Prog Interval Timer Int Enable 1-ms Timer Int Enable Read/Write R/W R/W R/W – – – – – Default 0 0 0 0 0 0 0 0 Reserved Bit 7: TCAP0 Interrupt Enable 0 = Mask TCAP0 interrupt 1 = Unmask TCAP0 interrupt Bit 6: Prog Interval Timer Interrupt Enable 0 = Mask Prog Interval Timer interrupt 1 = Unmask Prog Interval Timer interrupt Bit 5: 1-ms Timer Interrupt Enable 0 = Mask 1-ms interrupt 1 = Unmask 1-ms interrupt Bit [4:0]: Reserved Document 38-16016 Rev. *C Page 52 of 62 [+] Feedback CY7C601xx CY7C602xx Table 87. Interrupt Mask 0 (INT_MSK0) [0xE0] [R/W] Bit # 7 6 5 4 3 2 1 0 Field GPIO Port 1 Int Enable Sleep Timer Int Enable INT1 Int Enable GPIO Port 0 Int Enable SPI Receive Int Enable SPI Transmit Int Enable INT0 Int Enable POR/LVD Int Enable Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 3 2 1 0 Bit 7: GPIO Port 1 Interrupt Enable 0 = Mask GPIO Port 1 interrupt 1 = Unmask GPIO Port 1 interrupt Bit 6: Sleep Timer Interrupt Enable 0 = Mask Sleep Timer interrupt 1 = Unmask Sleep Timer interrupt Bit 5: INT1 Interrupt Enable 0 = Mask INT1 interrupt 1 = Unmask INT1 interrupt Bit 4: GPIO Port 0 Interrupt Enable 0 = Mask GPIO Port 0 interrupt 1 = Unmask GPIO Port 0 interrupt Bit 3: SPI Receive Interrupt Enable 0 = Mask SPI Receive interrupt 1 = Unmask SPI Receive interrupt Bit 2: SPI Transmit Enable 0 = Mask SPI Transmit interrupt 1 = Unmask SPI Transmit interrupt Bit 1: INT0 Interrupt Enable 0 = Mask INT0 interrupt 1 = Unmask INT0 interrupt Bit 0: POR/LVD Interrupt Enable 0 = Mask POR/LVD interrupt 1 = Unmask POR/LVD interrupt Interrupt Vector Clear Register Table 88.Interrupt Vector Clear Register (INT_VC) [0xE2] [R/W] Bit # 7 6 5 Field 4 Pending Interrupt [7:0] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 The Interrupt Vector Clear Register (INT_VC) holds the interrupt vector for the highest priority pending interrupt when read, and when written will clear all pending interrupts Bit [7:0]: Pending Interrupt [7:0] 8-bit data value holds the interrupt vector for the highest priority pending interrupt. Writing to this register will clear all pending interrupts. Document 38-16016 Rev. *C Page 53 of 62 [+] Feedback CY7C601xx CY7C602xx Absolute Maximum Ratings Maximum Total Sink Output Current into Port 0 and 1 and Pins............................................................. 70 mA Storage Temperature ................................. –65°C to +150°C Maximum Total Source Output Current into GPIO Pins30 mA Ambient Temperature with Power Applied ..... –0°C to +70°C Supply Voltage on VCC Relative to VSS ......... –0.5V to +7.0V Maximum On-chip Power Dissipation on any GPIO Pin......................................................... 50 mW DC Input Voltage................................ –0.5V to + VCC + 0.5V Power Dissipation .................................................... 300 mW DC Voltage Applied to Outputs in High-Z State ....................................... –0.5V to + VCC + 0.5V Static Discharge Voltage ............................................. 2200V Latch-up Current ...................................................... 200 mA DC Characteristics Description Parameter Conditions General VCC1 Operating Voltage CPU speed <= 12 MHz TFP Operating Temp Flash Programming ICC1 VCC Operating Supply Current ICC2 VCC Operating Supply Current ISB1 Standby Current Min. Typical Max. Unit 2.7 3.6 V 0 70 °C CPU speed = 12 MHz 11 mA CPU speed = 6 MHz 9 mA Internal and External Oscillators, Bandgap, Flash, CPU Clock, Timer Clock all disabled 10 µA 2.7 V Low-voltage Detect VLVD Low-voltage detect Trip Voltage LVDCR [2:0] set to 000 2.681 General Purpose I/O Interface RUP Pull Up Resistance 4 12 KΩ VICR Input Threshold Voltage Low, CMOS mode Low to High edge 40% 65% VCC VICF Input Threshold Voltage Low, CMOS mode High to Low edge 30% 55% VCC VHC Input Hysteresis Voltage, CMOS Mode High to low edge 3% 10% VCC VILTTL Input Low Voltage, TTL Mode 0.72 V VIHTTL Input HIGH Voltage, TTL Mode 1.6 V VOL1 Output Low Voltage, High Drive[4] IOL1 = 50 mA 1.4 V VOL2 Output Low Voltage, High Drive[4] IOL1 = 25 mA 0.4 V VOL3 Output Low Voltage, Low Drive IOL2 = 8 mA VOH Output High Voltage[4] IOH = 2 mA 0.8 VCC – 0.5 V V AC Characteristics Parameter Description Conditions Min. Typical Max. Unit Clock TECLKDC External Clock Duty Cycle 45 55 % TECLK2 External Clock Frequency 1 24 MHz GPIO Timing TR_GPIO Output Rise Time Measured between 10 and 90% Vdd/Vreg with 50 pF load 50 ns TF_GPIO Output Fall Time Measured between 10 and 90% Vdd/Vreg with 50 pF load 15 ns Note 4. Available only on CY7C601xx P2.7, P3.7, P0.0, P0.1; CY7C602xx P1.3,P1.4,P1.5,P1.6,P1.7. Document 38-16016 Rev. *C Page 54 of 62 [+] Feedback CY7C601xx CY7C602xx AC Characteristics (continued) Parameter Description Conditions Min. Typical Max. Unit 2 MHz 2.2 MHz SPI Timing TSMCK SPI Master Clock Rate TSSCK SPI Slave Clock Rate FCPUCLK/6 TSCKH SPI Clock High Time High for CPOL = 0, Low for CPOL = 1 125 ns TSCKL SPI Clock Low Time Low for CPOL = 0, High for CPOL = 1 125 ns TMDO Master Data Output Time[5] SCK to data valid –25 TMDO1 Master Data Output Time, First bit with CPHA = 0 Time before leading SCK edge 100 ns TMSU Master Input Data Setup time 50 ns TMHD Master Input Data Hold time 50 ns TSSU Slave Input Data Setup Time 50 ns TSHD Slave Input Data Hold Time TSDO Slave Data Output Time SCK to data valid 100 ns TSDO1 Slave Data Output Time, First bit with CPHA = 0 Time after SS LOW to data valid 100 ns TSSS Slave Select Setup Time Before first SCK edge 150 ns TSSH Slave Select Hold Time After last SCK edge 150 ns 50 50 ns ns Figure 18. Clock Timing TCYC TCH CLOCK TCL Figure 19. GPIO Timing Diagram 90% GPIO Pin Output Voltage 10% TR_GPIO TF_GPIO Note 5. In Master mode first bit is available 0.5 SPICLK cycle before Master clock edge available on the SCLK pin. Document 38-16016 Rev. *C Page 55 of 62 [+] Feedback CY7C601xx CY7C602xx Figure 20. SPI Master Timing, CPHA = 1 SS (SS is under firmware control in SPI Master mode) TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) TMDO MSB MOSI MSB MISO LSB LSB TMSU TMHD Figure 21. SPI Slave Timing, CPHA = 1 SS TSSS TSSH TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) MOSI MSB TSDO MISO Document 38-16016 Rev. *C LSB TSSU TSHD MSB LSB Page 56 of 62 [+] Feedback CY7C601xx CY7C602xx Figure 22. SPI Master Timing, CPHA = 0 SS (SS is under firmware control in SPI Master mode) TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) TMDO TMDO1 MSB MOSI LSB MSB MISO LSB TMSU TMHD Figure 23. SPI Slave Timing, CPHA = 0 SS TSSH TSSS TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) MSB MOSI LSB TSSU TSHD TSDO TSDO1 MISO Document 38-16016 Rev. *C MSB LSB Page 57 of 62 [+] Feedback CY7C601xx CY7C602xx 1 Ordering Information Ordering Code FLASH Size RAM Size Package Type CY7C60123-PVXC 8K 256 48-SSOP CY7C60123-PXC 8K 256 40-PDIP CY7C60113-PVXC 8K 256 28-SSOP CY7C60223-PXC 8K 256 24-PDIP CY7C60223-SXC 8K 256 24-SOIC CY7C60223-QXC 8K 256 24-QSOP Package Diagrams Figure 24. 24-Lead (300-Mil) SOIC S13 NOTE : 1. JEDEC STD REF MO-119 PIN 1 ID 2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH,BUT DOES INCLUDE MOLD MISMATCH AND ARE MEASURED AT THE MOLD PARTING LINE. 12 1 MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.010 in (0.254 mm) PER SIDE 3. DIMENSIONS IN INCHES MIN. MAX. 4. PACKAGE WEIGHT 0.65gms 0.291[7.391] 0.300[7.620] * 0.394[10.007] 0.419[10.642] 13 24 PART # S24.3 STANDARD PKG. SZ24.3 LEAD FREE PKG. 0.026[0.660] 0.032[0.812] SEATING PLANE 0.597[15.163] 0.615[15.621] 0.092[2.336] 0.105[2.667] * 0.050[1.270] TYP. 0.004[0.101] 0.0118[0.299] * 0.004[0.101] 0.015[0.381] 0.050[1.270] 0.0091[0.231] 0.0125[0.317] 0.013[0.330] 0.019[0.482] 51-85025 *C Document 38-16016 Rev. *C Page 58 of 62 [+] Feedback CY7C601xx CY7C602xx Package Diagrams (continued) Figure 25. 24-Lead (300-Mil) PDIP P13 51-85013-*B Figure 26. 24-lead QSOP O241 0.033 REF. 12 0.228 1 PIN 1 ID 0.150 0.157 DIMENSIONS IN INCHES MIN. MAX. 0.244 13 24 0.337 0.344 SEATING PLANE 0.007 0.010 0.053 0.069 0.004 0.004 0.010 Document 38-16016 Rev. *C 0.008 0.012 0.025 BSC. 0.016 0.034 0°-8° 51-85055-*B Page 59 of 62 [+] Feedback CY7C601xx CY7C602xx Package Diagrams (continued) Figure 27. 28-Lead (5.3 mm) Shrunk Small Outline Package O28 51-85079-*C Figure 28. 40-Lead (600-Mil) Molded DIP P17 51-85019-*A Document 38-16016 Rev. *C Page 60 of 62 [+] Feedback CY7C601xx CY7C602xx Package Diagrams (continued) Figure 29. 48-Lead Shrunk Small Outline Package O48 51-85061-*C PSoC is a registered trademark and enCoRe is a trademark of Cypress Semiconductor Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document 38-16016 Rev. *C Page 61 of 62 © Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. [+] Feedback CY7C601xx CY7C602xx Document History Page Document Title: CY7C601/2xx enCoRe™ II Low Voltage Microcontroller Document Number: 38-16016 Rev. ECN No. Issue Date Orig. of Change ** 327601 See ECN BON New data sheet *A 400134 See ECN BHA Updated Power consumption values Corrected Pin Assignment Table for 24 QSOP, 24 PDIP and 28 SSOP packages Minor text changes for clarification purposes Corrected INT_MSK0 and INT_MSK1 register address Corrected register bit definitions Corrected Protection Mode Settings in Table 10-7 Updated LVD Trip Point values Added Block diagrams for Timer functional timing Replaced TBD’s with actual values Added SPI Block Diagram Added Timing Block Diagrams Removed CY7C60123 DIE from Figure 5-1 Removed CY7C60123-WXC from Section 22.0 Ordering Information Updated internal 24 MHz Oscillator accuracy information Added information on sending/receiving data when using 32 KHz oscillator *B 505222 See ECN TYJ Minor text changes GPIO capacitance and timing diagram included Method to clear Capture Interrupt Status bit discussed Sleep and Wakeup sequence documented PIT Timer registers’ R/W capability corrected to read only Modified Free Running Counter text in section 17.1.1 *C 524104 See ECN Document 38-16016 Rev. *C Description of Change KKVTMP Change title from Wireless enCoRe II to enCoRe II Low Voltage Page 62 of 62 [+] Feedback