TSOP11..UU1 Vishay Telefunken Photo Modules for PCM Remote Control Systems Available types for different carrier frequencies Type TSOP1130UU1 TSOP1136UU1 TSOP1138UU1 TSOP1156UU1 fo 30 kHz 36 kHz 38 kHz 56 kHz Type TSOP1133UU1 TSOP1137UU1 TSOP1140UU1 fo 33 kHz 36.7 kHz 40 kHz Description The TSOP11..UU1 – series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the operation with short burst transmission codes (e.g. RECS 80) and high data rates. 13 642 D Low power consumption D High immunity against ambient light Features D Photo detector and preamplifier in one package D Internal filter for PCM frequency D Improved shielding against electrical field Special Features disturbance D TTL and CMOS compatibility D Output active low D Enhanced data rate of 3500 bit/s D Operation with short bursts possible (≥6 cycles/burst) Block Diagram 2 Control Circuit Input 80 kW 3 PIN AGC Band Pass VS OUT Demodulator 1 GND 94 8136 Document Number 82012 Rev. 9, 29-Mar-01 www.vishay.com 1 (8) TSOP11..UU1 Vishay Telefunken Absolute Maximum Ratings Tamb = 25_C Parameter Supply Voltage Supply Current Output Voltage Output Current Junction Temperature Storage Temperature Range Operating Temperature Range Power Consumption Soldering Temperature Test Conditions (Pin 2) (Pin 2) (Pin 3) (Pin 3) Symbol VS IS VO IO Tj Tstg Tamb Ptot Tsd x (Tamb 85 °C) t 5s x Value –0.3...6.0 5 –0.3...6.0 5 100 –25...+85 –25...+85 50 260 Unit V mA V mA °C °C °C mW °C Typ 0.6 1 Unit mA mA V m Basic Characteristics Tamb = 25_C Parameter Supply y Current ((Pin 2)) Supply Voltage (Pin 2) Transmission Distance Output Voltage Low (Pin 3) Irradiance ((30 – 40 kHz)) Irradiance ((56 kHz)) Irradiance Directivity Test Conditions VS = 5 V, Ev = 0 VS = 5 V, Ev = 40 klx, sunlight Ev = 0, test signal see fig.8, IR diode TSAL6200, IF = 0.4 A IOSL = 0.5 mA,Ee = 0.7 mW/m2, f = fo, test signal see fig.7 Test signal see fig.7 Test signal see fig.8 Test signal see fig.7 Test signal see fig.8 Test signal see fig.7 Angle of half transmission distance Symbol ISD ISH VS d Min 0.4 4.5 5.5 35 VOSL Ee min Ee min Ee min Ee min Ee max ϕ1/2 Max 1.5 0.4 0.35 0.45 0.40 250 mV 0.6 0.5 0.7 0.6 mW/m2 mW/m2 mW/m2 mW/m2 W/m2 deg 30 ±45 Application Circuit 100 W *) 2 TSOP11.. TSAL62.. 4.7 mF *) +5V >10 kW optional 3 mC **) 1 12755 GND *) recommended to suppress power supply disturbances **) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit. www.vishay.com 2 (8) Document Number 82012 Rev. 9, 29 Mar-01 TSOP11..UU1 Vishay Telefunken Suitable Data Format The circuit of the TSOP11..UU1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fullfill the following condition: • Carrier frequency should be close to center frequency of the bandpass (e.g. 38kHz). • Burst length should be 6 cycles/burst or longer. Some examples for suitable data format are: NEC Code, Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, RCMM Code, R–2000 Code, RECS–80 Code. When a disturbance signal is applied to the TSOP11..UU1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure. Some examples for such disturbance signals which are suppressed by the TSOP11..UU1 are: • After each burst which is between 6 cycles and 70 cycles a gap time of at least 10 cycles is neccessary. • DC light (e.g. from tungsten bulb or sunlight) • For each burst which is longer than 1.8ms a corresponding gap time is necessary at some time in the data stream. This gap time should have at least same length as the burst. • Continuous signal at 38kHz or at any other frequency • Up to 2200 short bursts per second can be received continuously. 0 5 • Signals from fluorescent lamps with electronic ballast (an example of the signal modulation is in the figure below). 10 15 20 time [ms] IR Signal from Fluorescent Lamp with low Modulation Document Number 82012 Rev. 9, 29-Mar-01 www.vishay.com 3 (8) TSOP11..UU1 Vishay Telefunken Typical Characteristics (Tamb = 25_C unless otherwise specified) Ee min – Threshold Irradiance ( mW/m2 ) /eE – Rel. Responsitivity 1.0 0.8 0.6 0.4 eE min 0.2 f = f0 "5% Df ( 3 dB ) = f0 / 7 2.0 f ( E ) = f0 1.6 1.2 0.8 0.4 0.0 0.0 0.7 0.8 0.9 1.0 1.1 1.3 1.2 f / f0 – Relative Frequency 94 9102 Figure 1. Frequency Dependence of Responsivity 0.25 0.20 Input burst duration 0.15 l = 950 nm, optical test signal, fig.7 0.05 0 0.1 1.0 10.0 Ee – Irradiance ( 12751 5.0 4.5 4.0 3.5 ^ ^ Correlation with ambient light sources ( Disturbance effect ) : 10W/m2 1.4 klx ( Stand.illum.A, T = 2855 K ) 8.2 klx ( Daylight, T = 5900 K ) 3.0 2.5 2.0 1.5 Ambient, l = 950 nm 1.0 0.5 0 0.01 0.10 1.00 10.00 Figure 3. Sensitivity in Bright Ambient www.vishay.com 4 (8) 1 kHz 10 kHz 1 100 Hz 0.1 1 10 100 1000 DVs RMS – AC Voltage on DC Supply Voltage ( mV ) Figure 5. Sensitivity vs. Supply Voltage Disturbances 1.0 0.9 0.8 Sensitivity in dark ambient 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 –30 –15 100.00 E – DC Irradiance (W/m2) 96 12111 2.0 1.6 f = f0 0.1 0.01 E e min – Threshold Irradiance (mW/m2 ) E e min – Threshold Irradiance (mW/m2 ) Figure 2. Pulse Length and Sensitivity in Dark Ambient 1.2 10 94 9106 ) 0.8 Figure 4. Sensitivity vs. Electric Field Disturbances 100.0 1000.0 10000.0 mW/m2 0.4 E – Field Strength of Disturbance ( kV / m ) Ee min – Threshold Irradiance ( mW/m2 ) tpo – Output Pulse Length (ms) 0.30 0.10 0.0 94 8147 96 12112 0 15 30 45 60 75 90 Tamb – Ambient Temperature ( °C ) Figure 6. Sensitivity vs. Ambient Temperature Document Number 82012 Rev. 9, 29 Mar-01 TSOP11..UU1 Vishay Telefunken Optical Test Signal ( IR diode TSAL6200, IF=0.4 A, N=6 pulses, f=f0, T=10 ms ) tpi t * T * tpi w 6/fo is recommended for optimal function Output Signal VO 1) 2) VOH 14337 3/f0 < td < 9/f0 tpi – 4/f0 < tpo < tpi + 6/f0 0.8 0.6 0.5 Toff 0.4 0.3 l = 950 nm, optical test signal, fig.8 0.2 0.1 1.0 t 10.0 100.0 1000.0 10000.0 Ee – Irradiance (mW/m2) 12753 tpo2 ) Figure 7. Output Function Ee Ton 0.7 0 0.1 VOL td1 ) 0.9 T on ,Toff – Output Pulse Length (ms) Ee Figure 10. Output Pulse Diagram Optical Test Signal 1.0 600 ms t 600 ms T = 60 ms 94 8134 VO Output Signal, ( see Fig.10 ) I s – Supply Current ( mA ) 0.9 0.7 0.6 0.5 0.4 0.3 0.2 0.1 VOH 0 –30 –15 VOL Ton t Toff S ( l ) rel – Relative Spectral Sensitivity 1.0 f = 38 kHz 0.9 Envelope Duty Cycle 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 10 20 30 40 50 60 70 80 90 Burstlength [number of cycles/burst] Figure 9. Max. Envelope Duty Cycle vs. Burstlength Document Number 82012 Rev. 9, 29-Mar-01 15 30 45 60 75 90 1.2 1.0 0.8 0.6 0.4 0.2 0 750 0 0 0 Tamb – Ambient Temperature ( °C ) 96 12115 Figure 11. Supply Current vs. Ambient Temperature Figure 8. Output Function 16152 Vs = 5 V 0.8 94 8408 850 950 1050 1150 l – Wavelength ( nm ) Figure 12. Relative Spectral Sensitivity vs. Wavelength www.vishay.com 5 (8) TSOP11..UU1 Vishay Telefunken 0° 10° 20° 0° 10° 20° 30° 30° 40° 1.0 40° 1.0 0.9 50° 0.9 50° 0.8 60° 0.8 60° 70° 0.7 70° 0.7 80° 0.6 95 11339p2 0.6 0.4 0.2 0 0.2 0.4 drel – Relative Transmission Distance Figure 13. Vertical Directivity ϕy www.vishay.com 6 (8) 80° 0.6 95 11340p2 0.6 0.4 0.2 0 0.2 0.4 drel – Relative Transmission Distance Figure 14. Horizontal Directivity ϕx Document Number 82012 Rev. 9, 29 Mar-01 TSOP11..UU1 Vishay Telefunken Dimensions in mm 12827 Document Number 82012 Rev. 9, 29-Mar-01 www.vishay.com 7 (8) TSOP11..UU1 Vishay Telefunken Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs ). The Montreal Protocol ( 1987 ) and its London Amendments ( 1990 ) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA ) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay-Telefunken products for any unintended or unauthorized application, the buyer shall indemnify Vishay-Telefunken against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423 www.vishay.com 8 (8) Document Number 82012 Rev. 9, 29 Mar-01