View detail for Guidelines to Keep ADC Resolution within Specification

Guidelines to Keep ADC Resolution within
Specification
Introduction
This application note describes how to optimize the ADC hardware environment in
order not to alter the intrinsic ADC resolution and to provide the best overall performance. Indeed, the resolution depends on both the ADC intrinsic noise and noise
transmitted by an external environment such as package impedances, power-supply
networks, de-coupling networks, loops and antennas. Some electromagnetic mechanisms have to be known in order to improve immunity against radiated and conducted
emissions. The environment noise level of a digital product is typically equal to
± 50 mV. The resolution of 10-bit ADC is 4.88 mV for a 5V voltage reference. Without
any precaution up to four bits can be lost, thus degrading the ADC from 10-bit to 6-bit.
8051
Microcontrollers
Application Note
ADC Resolution
Two classes of noise can be defined in the ADC. The first is due to the conversion process called quantization and the second one is due the noise coming from the
external environment of the electronic system.
Rev. 4278B–8051–08/03
Quantization Noise
The ADC operation is an analog to digital conversion which translates an analog signal
into a number called a digital sample as shown in Figure 1.
Figure 1. Analog to Digital Process
vaind(t)
vain(t)
Analog
to
Digital
Converter
E
Vref
Q = -----------N
Digital samples
N
0
0
t
Continuous Signal
Discret Signal
t
This process is needed each time a continuous signal (analog) has to be handle by a
digital system such as a computer. It can compute only discrete signals (digital). A continuous signal has an infinity of values. A discrete signal has only a finite number of
values. A digital sample is an approximation of the continuous value. This approximation
depends on the number of digital values that vain can take per sample. In other words it
depends on the bit number used to code vain in digital format. The higher the number of
bits, the better the approximation.
Table 1. Coding Format
Number of bit
6
8
10
12
Number of digital value
64
256
1024
4096
Q(mV), Vref = 5V
78.12
19.53
4.88
1.22
The quality of this approximation is defined as the ADC resolution. The higher the number of bits, the better the resolution. The resolution can be expressed in voltage and it
corresponds to the smaller voltage which can be translated by the ADC. This minimum
voltage is called voltage step or quantum (Q). It depends on the converter voltage reference (Vref) and the combination number (N):
Vref
Q = -----------N
Q which characterizes the conversion accuracy and is equal to ± 1/2 LSB. This conversion process is the first source of noise called RMS quantization noise vn.
It is shown in Figure 2 and is equal to:
q
vn ( V ) = ---------12
2
4278B–8051–08/03
Figure 2. The ADC Operation Adds Noise Quantization
vind(f)
vin(f)
Q = Vref
N
q
vn = ---------12
ADC
f
f
Table 2 shows the quantum value and the quantization noise level according to the
number of bits.
Table 2. Quantum and Quantization Noise Levels According to the Bit Number
Number of bit
12
10
8
6
Q (mV)
1.22
4.88
19.53
7812
vn (mV RMS)
0.35
1.4
5.66
22.55
All values less than vn cannot be converted because they are in the ADC noise floor.
External Noise Sources
All the radiated and conducted emissions coupled to the vain and vref inputs can
degrade the ADC resolution. Figure 3 shows three kinds of potential noise sources:
•
the noise transmitted by the power-supply is totally rejected and a part of it is
coupled to the ADC inputs,
•
IO pins close to the ADC inputs are coupled through the package and a part of the
switching current is transmitted to these ADC pins,
•
radiated emissions are coupled to the ADC pins by the PCB tracks, loops and
antennas.
Figure 3. System Noise Floor Affects the Resolution
Electromagnetic
sources
Power-supply
ADC
Vain/Vref
I/O pin crosstalk
3
4278B–8051–08/03
Figure 4 illustrates the ADC resolution degradation when the external noise is not
rejected enough. In this example the ADC has 12 bits and the RMS quantization noise
level is 0.35 mV.
Figure 4. External Noise Degrades the 12-bit Converter Down to 9-bits
vain(f)
External noise
10 mV
Quantization noise
0.35 mV
f
The overall external noise level is evaluated at 10 mV and the number of bits lost is:
N
2 =2
10 mV
---------------------1, 22 mV
10mV
log ---------------------1, 22mV
, N = ------------------------------- = 3
log 2
The ADC resolution is degraded and the new resolution is 9-bits instead of 12-bit. This
example shows it is important to lower all the noise sources and to reduce all the coupling mechanisms in the electronic system in order to keep the ADC resolution in the
specification.
This application note describes how to locate and to lower all these disturbances.
Basic Checklist For
ADC Resolution
Optimization
Some items have to be checked in order to keep the ADC resolution within specification:
•
Analyze and locate noise sources and coupling mechanisms,
•
Select the appropriate power-supply networks,
•
Use the de-coupling Strategy described inside,
•
Use the smaller package,
•
Use a package with separate power-supply Pins,
•
Use separate analog and digital ground planes.
Noise Sources and
Coupling
Mechanisms
Typical ADC Application
Description
Figure 5 shows a typical ADC application. The IC0 is an Atmel microcontroller including
an ADC with an analog input (Ain) and a voltage reference input (Vref).
4
4278B–8051–08/03
Figure 5. Typical ADC Application
VDD
Cap1
Cap0
IC4
IC1
C0
Sensor
C1
Vref
C2
C3
IO
Ain
Vref
IC0
IC3
IC2
A sensor is connected to Ain and an external voltage reference to Vref. The IC1 is controlled by the IC0 IO pin. The IC2 and the IC3 are two external devices and one of the
PCB connections is routed close to the Vref connection. The IC4 shares the common
VDD.
Noise Source and
Coupling Mechanism
Analysis
Conducted Mode Analysis
Figure 6 describes the main noise sources and the main coupling mechanisms in conducted mode and how they can influence the ADC resolution. These are detailed below:
•
vn4: this noise is generated by all IC activities and is transmitted to the powersupply rails,
•
vn3,vn2: this noise is generated by the internal logic activities and through the
packaging impedances,
•
vn1: a current flowing through the PCB connection from the IC2 to the IC3, induces
a current and then the voltage drop vn1 which is transmitted to the Vref input of the
ADC comparator by magnetic coupling with the C2 connection,
•
vn0: The IC0 generates a signal on the IO pin. There is a magnetic coupling of the
package between the IO and the Ain pin. The current flowing into the IO pin induces
a current due to the magnetic coupling into the Ain pin and causes the voltage drop
vn0 on this pin.
The combination of all these noise sources can affect the overall ADC resolution. An
ADC operation is based on a voltage comparison between an analog signal and a programmable voltage reference. This comparison process is done until both comparator
inputs are equal. The result is an integer value which reflects the analog value. If a noise
is injected in one of both inputs the comparator result is affected and the digital value is
corrupted by this noise. If the same noise is injected in both inputs, in differential, the
noise contribution will be cancelled and the digital result will not be affected (common
mode).
5
4278B–8051–08/03
Figure 6. Noise Sources and Coupling Mechanisms
Power-Supply
& De-coupling
Networks
VDD
vn4
IC4
IC0
PCB connections
IC1
C0
vn2
IO
k0
Sensor
vn0
Ain
C1
+
Vref
C2
Vref
I.C Logic
Block
ADC
-
k1
k
vn1
vn3
Die
C3
IC2
ilogic
Package
IC3
Printed Circuit Board
Radiated Mode Analysis
In this mode the PCB layout has to be checked in order to find the loops and wires that
can act like antennas. In Figure 7 a PCB lay-out is given around the Ain input.
Figure 7. Loops and Wires Have to be Analyzed to Protect Them Against Electromagnetic Fields
E/H
E/H
Vref
IO
Ain
Vref
Rg
IC0
IC0
Zin
Vref
This topology can be:
•
a loop, if RG+Zin is low compared to the loop impedance (typically 100Ω),
•
an antenna, if RG+Zin is high compared to the loop impedance.
6
4278B–8051–08/03
The PCB connection impedance varies according to the frequency as shown in
Figure 8. In some bands the topology acts like an antenna and in other bands the topology acts like a loop. The topology impedance depends on:
•
nature and thickness of the dielectric (epoxy, glass, ceramic, ...),
•
the PCB track size (width, length, ...),
•
the PCB structure (ground plane or not, power plane or not, ...).
Conclusions
The general concept to have the best ADC resolution is to lower the amplitude of all the
noise sources. The power-supply network is the major contributor and its impedance
has to be lowered to the minimum in the frequency band of the component. The coupling mechanisms have to be reduced and the connection impedance has to be lowered
too.
Noise Optimization
To reduce the noise level of the overall system and obtain the best ADC resolution, each
contributor has to be optimized. This chapter discusses how to optimize the noise
sources (power-supply network and de-coupling network) and the coupling mechanisms
(package).
Power-Supply and Decoupling Networks
The power-supply network is a major contributor for the noise generation and it is important to maintain its impedance low especially in the frequency bands where the system
operates. The de-coupling network helps to reduce this impedance in the frequency
band where the IC operates (see application note ANM85).
Power-Supply Network
Several topologies can be used to implement the power-supply. The impedance across
power pins can vary from a few ohms to a hundred ohms:
•
PCB tracks,
•
One layer for ground and PCB tracks for the power,
•
Double layers for ground and power.
The choice of the topology is led by the price, the operation frequency and the protection
against the internal and external disturbances. When there is no constraint in terms of
emission and/or immunity, simple PCB tracks can be used to power the application. A
double layer connection is advised when the system operates in high frequency and
when the system is in a disturbed environment. To analyze the influence of the topology
on the connection inductance, the path of the return current has to be taken into account
to calculate the global inductance of the PCB connection.
PCB Tracks
A connection can be modelized by a RL model as it is shown in Figure 8. In low frequency the connection is a pure resistor and in high frequency it is an inductance. The
wider the PCB trace width, the lower the inductance.
7
4278B–8051–08/03
Figure 8. A PCB Connection is an RL Model
Z(f)
Ω
d
0.1mm
1mm
1cm
Resistance(ohm)
0.944
0.094
0.009
Inductance(nH)
340
258
168
PCB Trace
width, L = 10cm
d = 0.1mm
L
d = 1mm
e: PCB trace thickness in mm,
d: PCB trace width mm,
L: PCB length in m.
e = 36µm for typical PCB
One layer for Ground and PCB
Tracks for the Power
LT
d = 1cm
RT
If the PCB connection is too inductive, a ground layer allows to lower the inductance
value of the return current. A PCB connection is typically 5nH/cm and 0.8nH/cm for a
ground plane layer.
Figure 9. A Ground Layer Lowers the Inductance Value of the PCB Connection
w
L(nh/cm)
i
w = 10cm, wt = 1mm
l
LTrace
LPlane
wt
LT = LTrace + LPlane
h
h(mm)
Figure 9 gives both inductance values for the PCB connection implemented above a
ground plane and the inductance of the ground plane.
Double Layers for Ground and
Power
If the inductance is still too large, a double plane has to be used. The inductance for
both Vss and Vdd plane is around 2.5 pH/cm.
8
4278B–8051–08/03
Figure 10. A Double Copper Plane is the Lowest Inductance Topology
LVss(nH/cm)
VCC plane
LVcc(nH/cm)
l = 10cmw = 10cm
l
h
w
VSS plane
h(mm)
LPCB = LVcc+LVss
Figure 10 plots the inductance value of the VCC and VSS ground planes according to
the PCB thickness. It is the best topology to reduce the emission levels and to improve
the immunity.
Comparison Between the Three
Cases Described Above
Table 3 gives a comparison between all the three configurations analyzed above.
Table 3. Comparison of the PCB inductance for w=1mm, wt=10cm, l=10cm, h=1.6mm
Vcc PCB trace
Vcc PCB trace
Vcc Plane
Vss PCB trace
Vss plane
Vss Plane
Inductance (nH)
115 + 115 = 230
51 + 0.8 = 51.8
0.025 + 0.025 = 0.05
Capacitance (pF)
5 pF
20 pF
271 pF
The global inductance of a PCB connection with its return current connection is 406
higher than its equivalent double plane topology.
De-coupling Network
The role of the de-coupling network is to stabilize a power-supply network and to lower
the power impedance in the operation frequency bands of the system by:
•
maintaining a low impedance across the power-supply pins of ICs in the frequency
range of operation,
•
stabilizing the connections on the wiring connected between the power-supply
equipment and the electronic system equipment.
Figure 11. Capacitor Impedance According to the Frequency
ESL
Capacitor
Resistance
Inductor
C
ESL = 10nH
C = 100nH
ESR
ESR = 0.2oHm
9
4278B–8051–08/03
The de-coupling network uses some de-coupling capacitors. The impedance of a pure
capacitor decreases when the frequency increases. But a capacitor is not a pure one. It
consists of some parasitic elements such as an inductor (ESL) and a resistor (ESR). So
the capacitor model is a RLC circuit. The behavior of such a model according to the frequency is shown in Figure 11.
The equivalent inductance is the sum of the intrinsic inductance of the capacitor and the
inductance of the connection. Table 4 shows the RLC model for different capacitor technologies.
Table 4. Capacitor Characteristics Comparison
1µF Tantale
100nF Ceramic
10nF Ceramic
R
0.08
0.1
0.15
L(nH)
1.5
1.5
1.5
Fr(MHz)
2
7.1
29
Figure 12 plots the capacitor impedance according to the frequency and the capacitor
values.
Figure 12. The Capacitor Impedance is According to the Capacitor Values
× 10
4
1 . 10
3
3
1 . 10
100nF Ceramic
100
10nF Ceramic
Z1 ( f )
Z(f)
Z2 ( f )
Ω
10
Z3 ( f )
1
0.1
1µF tantale
0.08
0.01
4
1 . 10
5
1 . 10
6
1 . 10
7
1 . 10
8
1 . 10
Figure 13 plots the capacitor impedance according to the connection length between the
capacitor and the power pins. The longer the connection, the higher the inductance. The
resonance varies from 7 MHz to 30 MHz when the connection length varies from 0 to
5cm.
10
4278B–8051–08/03
Figure 13. The Capacitor Impedance According to the Connection Length
Z(f)
No connection
Ω
1cm
5cm
Vias are often used to connect capacitors to the ground are to the power planes. A via
has a typical inductance value of 1 nH.
Figure 14 shows a way to reduce the impedance by putting several identical capacitors
in parallel.
Figure 14. Several Identical Capacitors Helps to Lower the Impedance Value
1 x 10nF
2 x 10nF
4 x 10nF
De-coupling Strategy
The role of de-coupling capacitors is to maintain a low impedance across ICs. A digital
IC works synchronously to a clock and therefore most of the dynamic currents are synchronized to that one. A de-coupling capacitor has to be tuned around that clock
frequency in order to short-circuit the disturbance synchronous to the clock. To do this,
the RLC model of the connection taken between the VDD and the VSS pins has to evaluated. The equivalent inductance is the sum of LC, LP2 and LP1.
11
4278B–8051–08/03
Figure 15. Electrical Model of the Basic de-coupling Network
LP1
VDD
PCB
C
VDD
LP1
C
IO
Ain
Vref
LC
IC0
LP2
VSS
LP2
VSS
If the clock frequency is F0, then the de-coupling capacitor can be evaluated by the formula shown below:
1
C = ----------------------------------------------------------------------------------------2
( 2 × π × F 0 ) × ( LP 1 + LP 2 + LC )
The parasitic inductances depend on the de-coupling capacitor types and the PCB
topology chosen. For example, the capacitor is a SMD type and the intrinsic inductance
is 6 nH. The PCB has no power planes, the PCB connection inductances are 10 nH/cm
and the total connection length is 5cm, therefore LP1+LP2 = 50 nH. The clock is 12 MHz
and C is equal to 3.3 nF.
Figure 16 plots the impedance for a 3.3nF capacitor and the 56nH parasitic inductance.
This capacitor value ensures a minimum of impedance around the 12 MHz clock frequency. The fast digital currents are frequently a broad band signal and it is necessary
to maintain a low impedance until the 100 MHz band. To do this, some de-coupling
capacitors are added and if the double power plane topology is chosen a pure HF
capacitor should be added. The values are evaluated on the third overtones of the clock
frequency but should be adapted to the shape of the VDD current.
Figure 16. Frequency Response of the Power-supply Network
4
1 . 10
3
1 . 10
25nH
100
VDD
Z(f)
6nH
10
3.3nF
1
0.6
25nH
VSS
0.1
6
1 . 10
7
1 . 10
8
1 . 10
9
1 . 10
10
1 . 10
f
F(Hz)
12
4278B–8051–08/03
PCB Track Topology
Figure 17 plots the network impedance based on the rule mentioned above. The decoupling capacitors are connected to the VDD and the VSS pins by two PCB tracks. The
de-coupling capacitor values are given in Table 5.
Zp
vdd = VDD × -----------------------------ZP + Zpow
Table 5. De-coupling Capacitor Values
100 kHz
12 MHz
36 MHz
60 MHz
C0 = 47 µF
C1 = 3.3 nF
C2 = 330 pF
C3 = 120 pF
Figure 17. Power-supply Network Impedance for PCB Connections Without Ground Plane
87.783
100
6nH x 4
VDD
25nH
47mF 3.3nF 330pF120pF
10
VSS
25nH
ZT ( f )
0.6 x 4
1
0.581
0.1
5
1 . 10
1 × 10
6
1 . 10
5
7
1 . 10
f
F(Hz)
8
1 . 10
9
1 . 10
9.997 × 10
8
The impedance is maintained below 30Ω from 100 kHz to 100 MHz. With such a topology, it will be impossible to lower the impedance more above 200 MHz because the
inductance connection causes a high impedance in the VHF/UHF band. At 1 GHz the
impedance is below 80Ω.
One Ground Plane Layer and
PCB Tracks
Figure 18 plots the impedance network for ground plane topology and for the de-coupling capacitors given in Table 6.
Table 6. De-coupling Capacitor Values
100 KHz
12 MHz
36 MHz
60 MHz
C0 = 100 µF
C1 = 6.8 nF
C2 = 820 pF
C3 = 270 pF
13
4278B–8051–08/03
Figure 18. Power-supply Network Impedance for a Ground Plane Topology
40.756
100
6nH x 4
VDD
25nH
10
100µF 6.8nF 820pF 270pF
VSS
ZT ( f )
50pH
0.6 x 4
1
0.536
0.1
5
1 . 10
6
1 . 10
1 × 10
7
1 . 10
f
F(Hz)
5
8
1 . 10
9
1 . 10
9.997 × 10
8
The impedance is maintained below 6Ω from 100 kHz to 100 MHz. Compared to the first
topology, this ground plane divides the network impedance by five. As the first topology
it will be impossible to reduce the impedance more in the VHF/UHF band. At 1 GHZ the
impedance is below 40Ω.
Double Layers for VDD and VSS Figure 19 plots the impedance network for ground plane topology and for the de-coupling capacitors given in Table 7. The PCB capacitor is efficient in high frequency and
not in low frequency because in this range the impedance is too high. It is necessary to
have additional de-coupling capacitors.
Table 7. De-coupling Capacitor Values
100 KHz
12 MHz
36 MHz
60 MHz
PCB capacitor
C0 = 470 µF
C1 = 33 nF
C2 = 3.3 nF
C3 = 1.2 nF
270 pF
Figure 19. Power-supply Network Impedance for a Double Plane Topology
11.061
100
6nH x 4
VDD
50pH
10
ZT ( f )
470mF33nF 3.3nF 1.2nF 270pF
VSS
50pH
0.6 x 4
1
0.357
0.1
5
1 . 10
1 × 10
6
1 . 10
5
7
1 . 10
f
F(Hz)
8
1 . 10
9
1 . 10
9.997 × 10
8
The impedance is maintained below 1 ohm between 100 kHz to 100 MHz. Thanks to the
capacitor built with the double plane of the PCB, the impedance in the VHF/UHF band in
reduced down to 10Ω. This topology lowers the resistance and the inductance to the
minimum.
14
4278B–8051–08/03
Package Type
The package is the second major contributor and contributes to increasing the noise
level. The package is similar to an impedance and is a load to the power-supply network
as it is shown in Figure 20. The voltage variation across the package depends on
Zpow(f) and Zp(f):
The lower the package impedance, the lower the vdd variation.
Figure 20. The Package Impedance Increases the Noise Level
Zpow
vdd
Power-Supply
Power-supply Network
&
De-coupling Network
Zp(f)
vdd
Zp
vss
vss
The package connection consists of a lead-frame (package lay-out) and bond-wires.
The power-supply pins act as a magnetic loop or as an antenna. The bigger the package, the higher the Q factor thus the impedance
Figure 21. Package Impedance According to the Package Type and Frequency
Z(f)
LP
Ω
LP
DIL
LP
PLCC
LP
COB
PLCC
DIL
Package PLCC
LP
6nH
COB
DIL
20nH
2nH
F(Hz)
Figure 21 plots the impedance and the Q factor for three package types. Therefore it is
recommended to use the smallest package in order to reduce the impedance and the
topology antenna in the frequency band where the electronic system works.
15
4278B–8051–08/03
Power-Supply Pin
Configurations
Two kinds of configuration for the ground pin can be found and are shown in Figure 22.
The first one has two separate pins (Figure 22.a), one for the analog and one for the digital. The second one has only one ground pin (Figure 22.b).
Figure 22. Power-Supply Pin Configurations
Vdd
Vcca
Ain
Vcca
Vdd
Ainx
ADC
Logic
Vref
ADC
Logic
Vref
a)
Vss
Vssa
b)
Vss
To evaluate the performance of these configurations, the voltage difference between the
Ain and Vref inputs has to be evaluated. Indeed, the conversion process translates this
voltage difference. The noise affects the conversion result only if both inputs don’t
receive the same noise level value.
Common Ground pin
In this configuration shown in Figure 23, there is a common ground pin for both analog
and digital ground pins. Zp is the package impedance of the VSS pin. The package
impedance of the Ain and Vref inputs is shown in the electrical schematic. Zain and Zref
are the input impedances of the ADC. Logic activities create large digital currents, iDigital, which generate a noise level across the package impedance. The analog current,
iADC, is negligible compared to iDigital.
Figure 23. Equivalent Electrical Schematic for a Common Ground Pin
Vdd
vain
Rg
Dvadc
Ain
vref
Logic
Dvadc
Vref
Rref
Zain
Zain
Zref
iDigital
iADC
eg
Vref
Zp
Zref
vnoise
Vss
Rg
Rreg
vnoise
Vss
16
4278B–8051–08/03
The input voltage, vain and vref, can be expressed according to the noise source with
rg
Rref
vain = vnoise × ------------------------, vref = vnoise × -----------------------------rg + Zain
Rref + Zref
the formula shown below:
The next formula is used to evaluate the voltage difference between vain et vref:
Rref
Rg
∆vadc = vain – vref = vnoise ×  --------------------------- – ------------------------------
 Rg + Zain Rref + Zref
Finally, to improve the ADC immunity, both terms shown below have to be equal:
Rg
Rref
--------------------------- = -----------------------------Rg + Zain
Rref + Zref
Typically, both sensor and voltage reference impedances as well as both vref and ain
inputs have to be equal. In this case the noise generated by the digital activities does
not affect the ADC resolution.
Dedicated Analog and Digital
Ground Pins
In this configuration, the analog and digital grounds are separated. Zp is the package
impedance of the Vss pin. The package impedance of the Ain and Vref inputs as well
as Vssa are not taken into account.
Figure 24. Equivalent Electrical Schematic for Analog and Digital Ground Pins
Vdd
Rg
Ainx
vain
Dvadc
Dvadc
Vref
vref
Rref
eg
Zain
Vref
Logic
Zref
Rg
Rreg
Zain Zref
iDigital
Vssa
iADC
Shottky diode
Zp
Vss
Vssa
vnoise
vnoise
Vss
With such a configuration, the switching noise is not transmitted to the ADC inputs and
gives the best immunity. Two Shottcky diodes are inserted to prevent accidental voltage
(DC, ESD, ..) from developing between the two ground systems.
17
4278B–8051–08/03
Conclusions
The environment noise level of a digital product is typically equal to +/-50 mV. The resolution of a 10-bit ADC is 4.88 mV for a 5V voltage reference. Without any precaution,
typically up to 4 bits can be lost, thus degrading the ADC from 10-bits to 6-bits. In other
hand, keeping both the network and the IO interface impedance low allows to maintain a
9 to 10-bit resolution. This is why it is important to analyze and to optimize the powersupply and de-coupling networks as well as the IOs interfaces.
References
•
Controlling Radiated emissions by design, Michel Mardiguian, Chapman&Hall,
•
Printed Circuit Board Design Techniques for EMC Compliance, Mark I.Montrose,
IEEE Press,
•
Noise Reduction Techniques In Electronics Systems, Henry W. Ott, Wiley
Interscience.
•
High-Speed Digital Design, Johson / Graham, PTRPH.
•
High-Speed Signal Propagation, Johson / Graham, PTRPH.
•
Application Note, ANM085, EMC Improvement Guidelines, Atmel-wm, Jean-Luc
Levant
18
4278B–8051–08/03
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard
warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any
errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and
does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are
granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use
as critical components in life support devices or systems.
© Atmel Corporation 2003. All rights reserved. Atmel ® is a registered trademark of Atmel Corporation or its subsidiaries. Other terms and
product names may be the trademarks of others.
Printed on recycled paper.
4278B–8051–08/03