ATmega161(L) - Mature

Features
• High-performance, Low-power AVR® 8-bit Microcontroller
• Advanced RISC Architecture
•
•
•
•
•
•
•
•
– 130 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 8 MIPS Throughput at 8 MHz
– On-chip 2-cycle Multiplier
Program and Data Memories
– 16K Bytes of Non-volatile In-System Programmable Flash Endurance: 1,000
Write/Erase Cycles
– Optional Boot Code Memory with Independent Lock bits Self-programming of
Program and Data Memories
– 512 Bytes of Non-volatile In-System Programmable EEPROM Endurance: 100,000
Write/Erase Cycles
– 1K Byte of Internal SRAM
– Programming Lock for Software Security
Peripheral Features
– Two 8-bit Timer/Counters with Separate Prescaler and PWM
– Expanded 16-bit Timer/Counter System with Separate Prescaler, Compare,
Capture Modes and Dual 8-, 9-, or 10-bit PWM
– Dual Programmable Serial UARTs
– Master/Slave SPI Serial Interface
– Real-time Counter with Separate Oscillator
– Programmable Watchdog Timer with Separate On-chip Oscillator
– On-chip Analog Comparator
Special Microcontroller Features
– Power-on Reset
– External and Internal Interrupt Sources
– Three Sleep Modes: Idle, Power-save and Power-down
Power Comsumption at 4 MHz, 3.0V, 25°C
– Active 3.0 mA
– Idle Mode 1.2 mA
– Power-down Mode < 1 µA
I/O and Packages
– 35 Programmable I/O Lines
– 40-lead PDIP and 44-lead TQFP
Operating Voltages
– 2.7V - 5.5V for the ATmega161L
– 4.0V - 5.5V for the ATmega161
Speed Grades
– 0 - 4 MHz for the ATmega161L
– 0 - 8 MHz for the ATmega161
Commercial and Industrial Temperature Ranges
8-bit
Microcontroller
with 16K Bytes
of In-System
Programmable
Flash
ATmega161
ATmega161L
Disclaimer
Typical values contained in this data sheet are based on simulations and characterization of other AVR microcontrollers manufactured on the same process technology.
Min and Max values will be available after the device is characterized.
Note:
Not recommended in new
designs.
Rev. 1228D–AVR–02/07
1
Pin Configuration
PDIP
(OC0/T0) PB0
(OC2/T1) PB1
(RXD1/AIN0) PB2
(TXD1/AIN1) PB3
(SS) PB4
(MOSI) PB5
(MISO) PB6
(SCK) PB7
RESET
(RXD0) PD0
(TXD0) PD1
(INT0) PD2
(INT1) PD3
(TOSC1) PD4
(OC1A/TOSC2) PD5
(WR) PD6
(RD) PD7
XTAL2
XTAL1
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
VCC
PA0 (AD0)
PA1 (AD1)
PA2 (AD2)
PA3 (AD3)
PA4 (AD4)
PA5 (AD5)
PA6 (AD6)
PA7 (AD7)
PE0 (ICP/INT2)
PE1 (ALE)
PE2 (OC1B)
PC7 (A15)
PC6 (A14)
PC5 (A13)
PC4 (A12)
PC3 (A11)
PC2 (A10)
PC1 (A9)
PC0 (A8)
44
43
42
41
40
39
38
37
36
35
34
PB4 (SS)
PB3 (TXD1/AIN1)
PB2 (RXD1/AIN0)
PB1 (OC2/T1)
PB0 (OC0/T0)
NC*
VCC
PA0 (AD0)
PA1 (AD1)
PA2 (AD2)
PA3 (AD3)
TQFP
33
32
31
30
29
28
27
26
25
24
23
1
2
3
4
5
6
7
8
9
10
11
PA4 (AD4)
PA5 (AD5)
PA6 (AD6)
PA7 (AD7)
PE0 (ICP/INT2)
NC*
PE1 (ALE)
PE2 (OC1B)
PC7 (A15)
PC6 (A14)
PC5 (A13)
(WR) PD6
(RD) PD7
XTAL2
XTAL1
GND
NC*
(A8) PC0
(A9) PC1
(A10) PC2
(A11) PC3
(A12) PC4
12
13
14
15
16
17
18
19
20
21
22
(MOSI) PB5
(MISO) PB6
(SCK) PB7
RESET
(RXD0) PD0
NC*
(TXD0) PD1
(INT0) PD2
(INT1) PD3
(TOSC1) PD4
(OCIA/TOSC2) PD5
2
* NC = Do not connect
(Can be used in future devices)
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Description
The ATmega161 is a low-power CMOS 8-bit microcontroller based on the AVR RISC
architecture. By executing powerful instructions in a single clock cycle, the ATmega161
achieves throughputs approaching 1 MIPS per MHz allowing the system designer to
optimize power consumption versus processing speed. The AVR core combines a rich
instruction set with 32 general purpose working registers. All the 32 registers are directly
connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be
accessed in one single instruction executed in one clock cycle. The resulting architecture is more code-efficient while achieving throughputs up to ten times faster than
conventional CISC microcontrollers.
The ATmega161 provides the following features: 16K bytes of In-System or Selfprogrammable Flash, 512 bytes EEPROM, 1K byte of SRAM, 35 general purpose I/O
lines, 32 general purpose working registers, Real-time Counter, three flexible
Timer/Counters with Compare modes, internal and external interrupts, two programmable serial UARTs, programmable Watchdog Timer with internal Oscillator, an SPI serial
port and three software-selectable power saving modes. The Idle mode stops the CPU
while allowing the SRAM, Timer/Counters, SPI port and interrupt system to continue
functioning. The Power-down mode saves the register and SRAM contents but freezes
the Oscillator, disabling all other chip functions until the next External Interrupt or Hardware Reset. In Power-save mode, the timer Oscillator continues to run, allowing the
user to maintain a timer base while the rest of the device is sleeping.
The device is manufactured using Atmel’s high-density non-volatile memory technology.
The On-chip Flash Program memory can be reprogrammed using the Self-programming
capability through the Boot Block and an ISP through the SPI port, or by using a conventional non-volatile Memory programmer. By combining an enhanced RISC 8-bit CPU
with In-System Programmable Flash on a monolithic chip, the Atmel ATmega161 is a
powerful microcontroller that provides a highly flexible and cost-effective solution to
many embedded control applications.
The ATmega161 AVR is supported with a full suite of program and system development
tools including: C compilers, macro assemblers, program debugger/simulators, In-Circuit Emulators and evaluation kits.
3
1228D–AVR–02/07
Block Diagram
Figure 1. The ATmega161 Block Diagram
PA0-PA7
PC0-PC7
PORTA DRIVERS
PORTC DRIVERS
VCC
GND
DATA REGISTER
PORTA
DATA DIR.
REG. PORTA
DATA REGISTER
PORTC
DATA DIR.
REG. PORTC
8-BIT DATA BUS
XTAL1
INTERNAL
OSCILLATOR
OSCILLATOR
TIMING AND
CONTROL
PROGRAM
COUNTER
STACK
POINTER
WATCHDOG
TIMER
PROGRAM
FLASH
SRAM
MCU CONTROL
REGISTER
INSTRUCTION
REGISTER
GENERAL
PURPOSE
REGISTERS
CONTROL
LINES
TIMER/
COUNTERS
X
Y
Z
INTERRUPT
UNIT
ALU
EEPROM
INSTRUCTION
DECODER
XTAL2
RESET
STATUS
REGISTER
ANALOG
COMPARATOR
PROGRAMMING
LOGIC
SPI
DATA REGISTER
PORTB
DATA DIR.
REG. PORTB
UARTS
DATA REGISTER
PORTD
DATA DIR.
REG. PORTD
DATA DIR
DATA REG.
REG. PORTE
PORTE
+
PORTB DRIVERS
PB0 - PB7
4
PORTD DRIVERS
PD0 - PD7
PORTE DRIVERS
PE0 - PE2
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Pin Descriptions
VCC
Supply voltage.
GND
Ground.
Port A (PA7..PA0)
Port A is an 8-bit bi-directional I/O port. Port pins can provide internal pull-up resistors
(selected for each bit). The Port A output buffers can sink 20 mA and can drive LED displays directly. When pins PA0 to PA7 are used as inputs and are externally pulled low,
they will source current if the internal pull-up resistors are activated. The Port A pins are
tri-stated when a reset condition becomes active, even if the clock is not running.
Port A serves as a Multiplexed Address/Data port when using external memory
interface.
Port B (PB7..PB0)
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors. The Port B output
buffers can sink 20 mA. As inputs, Port B pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port B also serves the functions of various special features of the ATmega161 as listed
on page 92.
Port C (PC7..PC0)
Port C is an 8-bit bi-directional I/O port with internal pull-up resistors. The Port C output
buffers can sink 20 mA. As inputs, Port C pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port C also serves as an address high output when using external memory interface.
Port D (PD7..PD0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors. The Port D output
buffers can sink 20 mA. As inputs, Port D pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port D also serves the functions of various special features of the ATmega161 as listed
on page 101.
Port E (PE2..PE0)
Port E is a 3-bit bi-directional I/O port with internal pull-up resistors. The Port E output
buffers can sink 20 mA. As inputs, Port E pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port E pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port E also serves the functions of various special features of the ATmega161 as listed
on page 107.
RESET
Reset input. A low level on this pin for more than 500 ns will generate a Reset, even if
the clock is not running. Shorter pulses are not guaranteed to generate a Reset.
XTAL1
Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.
XTAL2
Output from the inverting Oscillator amplifier.
5
1228D–AVR–02/07
Crystal Oscillator
XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier that can
be configured for use as an on-chip Oscillator, as shown in Figure 2. Either a quartz
crystal or a ceramic resonator may be used. To drive the device from an external clock
source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 3.
Figure 2. Oscillator Connections
C2
C1
XTAL2
XTAL1
GND
Figure 3. External Clock Drive Configuration
NC
XTAL2
EXTERNAL
OSCILLATOR
SIGNAL
XTAL1
GND
6
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Architectural
Overview
The fast-access Register File concept contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This means that during one single clock
cycle, one Arithmetic Logic Unit (ALU) operation is executed. Two operands are output
from the Register File, the operation is executed and the result is stored back in the
Register File – in one clock cycle.
Six of the 32 registers can be used as three 16-bit indirect address register pointers for
Data Space addressing – enabling efficient address calculations. One of the three
address pointers is also used as the address pointer for the constant table look-up function. These added function registers are the 16-bit X-register, Y-register and Z-register.
The ALU supports arithmetic and logic functions between registers or between a constant and a register. Single register operations are also executed in the ALU. Figure 4
shows the ATmega161 AVR RISC microcontroller architecture.
Figure 4. The ATmega161 AVR RISC Architecture
Data Bus 8-bit
8K x 16
Program
Memory
Program
Counter
Status
and Control
32 x 8
General
Purpose
Registers
Control Lines
Direct Addressing
Instruction
Decoder
Indirect Addressing
Instruction
Register
Interrupt
Unit
SPI
Unit
Serial
UART0
Serial
UART1
ALU
8-bit
Timer/Counter
with PWM
and RTC
1024 x 8
Data
SRAM
512 x 8
EEPROM
32
I/O Lines
16-bit
Timer/Counter
with PWM
8-bit
Timer/Counter
with PWM
Watchdog
Timer
Analog
Comparator
7
1228D–AVR–02/07
In addition to the register operation, the conventional Memory Addressing modes can be
used on the Register File. This is enabled by the fact that the Register File is assigned
the 32 lowermost Data Space addresses ($00 - $1F), allowing them to be accessed as
though they were ordinary memory locations.
The I/O memory space contains 64 addresses for CPU peripheral functions such as
Control Registers, Timer/Counters, and other I/O functions. The I/O memory can be
accessed directly or as the Data Space locations following those of the Register File,
$20 - $5F.
The AVR uses a Harvard architecture concept – with separate memories and buses for
program and data. The Program memory is executed with a two-stage pipeline. While
one instruction is being executed, the next instruction is pre-fetched from the Program
memory. This concept enables instructions to be executed in every clock cycle. The
Program memory is Self-programmable Flash memory.
With the jump and call instructions, the whole 8K word address space is directly
accessed. Most AVR instructions have a single 16-bit word format. Every Program
memory address contains a 16- or 32-bit instruction.
During interrupts and subroutine calls, the return address Program Counter (PC) is
stored on the Stack. The Stack is effectively allocated in the general data SRAM and,
consequently, the Stack size is only limited by the total SRAM size and the usage of the
SRAM. All user programs must initialize the SP (Stack Pointer) in the reset routine
(before subroutines or interrupts are executed). The 16-bit Stack Pointer is read/write
accessible in the I/O space.
The 1K byte data SRAM can be easily accessed through the five different Addressing
modes supported in the AVR architecture.
The memory spaces in the AVR architecture are all linear and regular memory maps.
8
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 5. Memory Maps
Data Memory
Program Memory
$000
32 Gen. Purpose $0000
Working Registers $001F
$0020
64 I/O Registers
Program Flash
(8K x 16)
$005F
$0060
Internal SRAM
(1024 x 8)
$045F
$0460
External SRAM
(0 - 63K x 8)
$1FFF
$FFFF
A flexible interrupt module has its control registers in the I/O space with an additional
global interrupt enable bit in the Status Register. All the different interrupts have a separate Interrupt Vector in the Interrupt Vector table at the beginning of the Program
memory. The different interrupts have priority in accordance with their Interrupt Vector
position. The lower the Interrupt Vector address, the higher the priority.
9
1228D–AVR–02/07
The General Purpose
Register File
Figure 6 shows the structure of the 32 general purpose working registers in the CPU.
Figure 6. AVR CPU General Purpose Working Registers
7
0
Addr.
R0
$00
R1
$01
R2
$02
…
R13
$0D
General
R14
$0E
Purpose
R15
$0F
Working
R16
$10
Registers
R17
$11
…
R26
$1A
X-register Low Byte
R27
$1B
X-register High Byte
R28
$1C
Y-register Low Byte
R29
$1D
Y-register High Byte
R30
$1E
Z-register Low Byte
R31
$1F
Z-register High Byte
All the register operating instructions in the instruction set have direct and single cycle
access to all registers. The only exceptions are the five constant arithmetic and logic
instructions SBCI, SUBI, CPI, ANDI, and ORI between a constant and a register, and
the LDI instruction for load immediate constant data. These instructions apply to the
second half of the registers in the Register File – R16..R31. The general SBC, SUB, CP,
AND, and OR, and all other operations between two registers or on a single register
apply to the entire Register File.
As shown in Figure 6, each register is also assigned a Data memory address, mapping
them directly into the first 32 locations of the user Data Space. Although not being physically implemented as SRAM locations, this memory organization provides great
flexibility in access of the registers, as the X-, Y-, and Z-registers can be set to index any
register in the file.
The X-register, Y-register and
Z-register
The registers R26..R31 have some added functions to their general purpose usage.
These registers are address pointers for indirect addressing of the Data Space. The
three indirect address registers X, Y, and Z are defined as:
Figure 7. X-, Y-, and Z-registers
15
X-register
7
0
0
R27 ($1B)
7
0
0
R29 ($1D)
7
R31 ($1F)
10
7
0
R28 ($1C)
15
Z-register
0
R26 ($1A)
15
Y-register
7
0
0
7
0
R30 ($1E)
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
In the different Addressing modes, these address registers have functions as fixed displacement, automatic increment and decrement (see the descriptions for the different
instructions).
ALU – Arithmetic Logic
Unit
The high-performance AVR ALU operates in direct connection with all the 32 general
purpose working registers. Within a single clock cycle, ALU operations between registers in the Register File are executed. The ALU operations are divided into three main
categories – arithmetic, logical and bit functions. ATmega161 also provides a powerful
multiplier supporting both signed/unsigned multiplication and fractional format. See the
Instruction Set section for a detailed description.
Self-programmable Flash The ATmega161 contains 16K bytes of On-chip Self-programmable and In-System Programmable Flash memory for program storage. Since all instructions are 16- or 32-bit
Program Memory
words, the Flash is organized as 8K x 16. The Flash memory has an endurance of at
least 1,000 write/erase cycles. The ATmega161 Program Counter (PC) is 13 bits wide,
thus addressing the 8,192 Program memory locations.
See page 110 for a detailed description of Flash data downloading.
See page 13 for the different Program Memory Addressing modes.
EEPROM Data Memory
The ATmega161 contains 512 bytes of data EEPROM memory. It is organized as a separate data space in which single bytes can be read and written. The EEPROM has an
endurance of at least 100,000 write/erase cycles per location. The interface between the
EEPROM and the CPU is described on page 60, specifying the EEPROM Address Registers, the EEPROM Data Register and the EEPROM Control Register.
For the SPI data downloading, see page 125 for a detailed description.
11
1228D–AVR–02/07
SRAM Data Memory
Figure 8 shows how the ATmega161 SRAM memory is organized.
Figure 8. SRAM Organization
Register File
Data Address Space
R0
$0000
R1
$0001
R2
$0002
…
…
R29
$001D
R30
$001E
R31
$001F
I/O Registers
$00
$0020
$01
$0021
$02
$0022
…
…
$3D
$005D
$3E
$005E
$3F
$005F
Internal SRAM
$0060
$0061
…
$045E
$045F
The lower 1120 Data memory locations address the Register File, the I/O memory and
the internal data SRAM. The first 96 locations address the Register File and I/O memory
and the next 1K locations address the internal data SRAM. An optional external Data
memory device can be placed in the same SRAM memory space. This memory device
will occupy the locations following the internal SRAM and up to as much as 64K - 1,
depending on external memory size.
When the addresses accessing the Data memory space exceed the internal data SRAM
locations, the memory device is accessed using the same instructions as for the internal
data SRAM access. When the internal data space is accessed, the read and write
strobe pins (RD and WR) are inactive during the whole access cycle. External memory
operation is enabled by setting the SRE bit in the MCUCR Register. See “Interface to
External Memory” on page 84 for details.
Accessing external memory takes one additional clock cycle per byte compared to
access of the internal SRAM. This means that the commands LD, ST, LDS, STS,
PUSH, and POP take one additional clock cycle. If the Stack is placed in external memory, interrupts, subroutine calls and returns take two clock cycles extra because the 2byte Program Counter is pushed and popped. When external memory interface is used
with wait state, two additional clock cycles are used per byte. This has the following
effect: Data transfer instructions take two extra clock cycles, whereas interrupt, subroutine calls and returns will need four clock cycles more than specified in the Instruction
Set manual.
12
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
The five different Addressing modes for the Data memory cover: Direct, Indirect with
Displacement, Indirect, Indirect with Pre-decrement and Indirect with Post-increment. In
the Register File, registers R26 to R31 feature the indirect Addressing Pointer
Registers.
The direct addressing reaches the entire data space.
The Indirect with Displacement mode features a 63-address locations reach from the
base address given by the Y- or Z-register.
When using Register Indirect Addressing modes with automatic pre-decrement and
post-increment, the address registers X, Y, and Z are decremented and incremented.
The 32 general purpose working registers, 64 I/O Registers and the 1K byte of internal
data SRAM in the ATmega161 are all accessible through all these Addressing modes.
See the next section for a detailed description of the different Addressing modes.
Program and Data
Addressing Modes
The ATmega161 AVR RISC microcontroller supports powerful and efficient Addressing
modes for access to the Program memory (Flash) and Data memory (SRAM, Register
File and I/O memory). This section describes the different Addressing modes supported
by the AVR architecture. In the figures, OP means the operation code part of the instruction word. To simplify, not all figures show the exact location of the addressing bits.
Register Direct, Single
Register Rd
Figure 9. Direct Single Register Addressing
REGISTER FILE
0
15
4
OP
0
d
d
31
The operand is contained in register d (Rd).
Register Direct, Two Registers
Rd and Rr
Figure 10. Direct Register Addressing, Two Registers
REGISTER FILE
0
15
9
OP
5 4
r
0
d
d
r
31
13
1228D–AVR–02/07
Operands are contained in registers r (Rr) and d (Rd). The result is stored in register d
(Rd).
I/O Direct
Figure 11. I/O Direct Addressing
I/O MEMORY
0
15
5
OP
n
0
P
63
Operand address is contained in six bits of the instruction word. n is the destination or
Source Register Address.
Data Direct
Figure 12. Direct Data Addressing
Data Space
20 19
31
OP
16
$0000
Rr/Rd
16 LSBs
15
0
$FFFF
A 16-bit data address is contained in the 16 LSBs of a two-word instruction. Rd/Rr specify the destination or source register.
14
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Data Indirect with
Displacement
Figure 13. Data Indirect with Displacement
Data Space
$0000
15
0
Y OR Z - REGISTER
15
10
OP
6 5
n
0
a
$FFFF
Operand address is the result of the Y- or Z-register contents added to the address contained in six bits of the instruction word.
Data Indirect
Figure 14. Data Indirect Addressing
Data Space
$0000
15
0
X, Y, OR Z - REGISTER
$FFFF
Operand address is the contents of the X-, Y-, or Z-register.
Data Indirect with Predecrement
Figure 15. Data Indirect Addressing with Pre-decrement
Data Space
$0000
15
0
X, Y, OR Z - REGISTER
-1
$FFFF
The X-, Y-, or Z-register is decremented before the operation. Operand address is the
decremented contents of the X-, Y-, or Z-register.
15
1228D–AVR–02/07
Data Indirect with Postincrement
Figure 16. Data Indirect Addressing with Post-increment
Data Space
$0000
15
0
X, Y, OR Z - REGISTER
1
$FFFF
The X-, Y-, or Z-register is incremented after the operation. Operand address is the contents of the X-, Y-, or Z-register prior to incrementing.
Constant Addressing Using
the LPM Instruction
Figure 17. Code Memory Constant Addressing
PROGRAM MEMORY
$000
15
1 0
Z-REGISTER
$1FFF
Constant byte address is specified by the Z-register contents. The 15 MSBs select word
address (0 - 8K), the LSB selects Low byte if cleared (LSB = 0) or High byte if set
(LSB = 1).
Indirect Program Addressing,
IJMP and ICALL
Figure 18. Indirect Program Memory Addressing
PROGRAM MEMORY
$000
15
0
Z-REGISTER
$1FFF
16
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Program execution continues at address contained by the Z-register (i.e., the PC is
loaded with the contents of the Z-register).
Relative Program Addressing,
RJMP and RCALL
Figure 19. Relative Program Memory Addressing
PROGRAM MEMORY
$000
15
0
PC
15
0
12 11
OP
k
$1FFF
Program execution continues at address PC + k + 1. The relative address k is -2048 to
2047.
Direct Program Addressing,
JMP and CALL
Figure 20. Direct Program Addressing
PROGRAM MEMORY
$0000
31
21 20
16
OP
16 LSBs
15
0
$1FFF
Program execution continues at the address immediate in the instruction words.
Memory Access Times
and Instruction
Execution Timing
This section describes the general access timing concepts for instruction execution and
internal memory access.
The AVR CPU is driven by the System Clock Ø, directly generated from the external
clock crystal for the chip. No internal clock division is used.
Figure 21 shows the parallel instruction fetches and instruction executions enabled by
the Harvard architecture and the fast-access Register File concept. This is the basic
pipelining concept to obtain up to 1 MIPS per MHz with the corresponding unique results
for functions per cost, functions per clocks and functions per power unit.
17
1228D–AVR–02/07
Figure 21. The Parallel Instruction Fetches and Instruction Executions
T1
T2
T3
T4
System Clock Ø
1st Instruction Fetch
1st Instruction Execute
2nd Instruction Fetch
2nd Instruction Execute
3rd Instruction Fetch
3rd Instruction Execute
4th Instruction Fetch
Figure 22 shows the internal timing concept for the Register File. In a single clock cycle
an ALU operation using two register operands is executed and the result is stored back
to the destination register.
Figure 22. Single Cycle ALU Operation
T1
T2
T3
T4
System Clock Ø
Total Execution Time
Register Operands Fetch
ALU Operation Execute
Result Write Back
The internal data SRAM access is performed in two System Clock cycles as described
in Figure 23.
Figure 23. On-chip Data SRAM Access Cycles
T1
T2
T3
T4
System Clock Ø
WR
Data
RD
18
Address
Write
Data
Prev. Address
Read
Address
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
l/O Memory
The I/O space definition of the ATmega161 is shown in Table 1.
Table 1. ATmega161 I/O Space(1)
I/O Address
(SRAM Address)
Name
Function
$3F($5F)
SREG
Status REGister
$3E ($5E)
SPH
Stack Pointer High
$3D ($5D)
SPL
Stack Pointer Low
$3B ($5B)
GIMSK
General Interrupt MaSK Register
$3A ($5A)
GIFR
General Interrupt Flag Register
$39 ($59)
TIMSK
Timer/Counter Interrupt MaSK Register
$38 ($58)
TIFR
Timer/Counter Interrupt Flag Register
$37 ($57)
SPMCR
Store Program Memory Control Register
$36 ($56)
EMCUCR
Extended MCU general Control Register
$35 ($55)
MCUCR
MCU general Control Register
$34 ($54)
MCUSR
MCU general Status Register
$33 ($53)
TCCR0
Timer/Counter0 Control Register
$32 ($52)
TCNT0
Timer/Counter0 (8-bit)
$31 ($51)
OCR0
Timer/Counter0 Output Compare Register
$30 ($50)
SFIOR
Special Function IO Register
$2F ($4F)
TCCR1A
Timer/Counter1 Control Register A
$2E ($4E)
TCCR1B
Timer/Counter1 Control Register B
$2D ($4D)
TCNT1H
Timer/Counter1 High Byte
$2C ($4C)
TCNT1L
Timer/Counter1 Low Byte
$2B ($4B)
OCR1AH
Timer/Counter1 Output Compare RegisterA High Byte
$2A ($4A)
OCR1AL
Timer/Counter1 Output Compare RegisterA Low Byte
$29 ($49)
OCR1BH
Timer/Counter1 Output Compare RegisterB High Byte
$28 ($48)
OCR1BL
Timer/Counter1 Output Compare RegisterB Low Byte
$27 ($47)
TCCR2
Timer/Counter2 Control Register
$26 ($46)
ASSR
Asynchronous mode StatuS Register
$25 ($45)
ICR1H
Timer/Counter1 Input Capture Register High Byte
$24 ($44)
ICR1L
Timer/Counter1 Input Capture Register Low Byte
$23 ($43)
TCNT2
Timer/Counter2 (8-bit)
$22 ($42)
OCR2
Timer/Counter2 Output Compare Register
$21 ($41)
WDTCR
Watchdog Timer Control Register
$20 ($40)
UBRRHI
UART Baud Register HIgh
$1F ($3F)
EEARH
EEPROM Address Register High
$1E ($3E)
EEARL
EEPROM Address Register Low
$1D ($3D)
EEDR
EEPROM Data Register
19
1228D–AVR–02/07
Table 1. ATmega161 I/O Space(1) (Continued)
I/O Address
(SRAM Address)
Name
Function
$1C ($3C)
EECR
EEPROM Control Register
$1B($3B)
PORTA
Data Register, Port A
$1A ($3A)
DDRA
Data Direction Register, Port A
$19 ($39)
PINA
Input Pins, Port A
$18 ($38)
PORTB
Data Register, Port B
$17 ($37)
DDRB
Data Direction Register, Port B
$16 ($36)
PINB
Input Pins, Port B
$15 ($35)
PORTC
Data Register, Port C
$14 ($34)
DDRC
Data Direction Register, Port C
$13 ($33)
PINC
Input Pins, Port C
$12 ($32)
PORTD
Data Register, Port D
$11 ($31)
DDRD
Data Direction Register, Port D
$10 ($30)
PIND
Input Pins, Port D
$0F ($2F)
SPDR
SPI I/O Data Register
$0E ($2E)
SPSR
SPI Status Register
$0D ($2D)
SPCR
SPI Control Register
$0C ($2C)
UDR0
UART0 I/O Data Register
$0B ($2B)
UCSR0A
UART0 Control and Status Register
$0A ($2A)
UCSR0B
UART0 Control and Status Register
$09 ($29)
UBRR0
UART0 Baud Rate Register
$08 ($28)
ACSR
Analog Comparator Control and Status Register
$07 ($27)
PORTE
Data Register, Port E
$06 ($26)
DDRE
Data Direction Register, Port E
$05 ($25)
PINE
Input Pins, Port E
$03 ($23)
UDR1
UART1 I/O Data Register
$02 ($22)
UCSR1A
UART1 Control and Status Register
$01 ($21)
UCSR1B
UART1 Control and Status Register
$00 ($20)
UBRR1
UART1 Baud Rate Register
Note:
20
1. Reserved and unused locations are not shown in this table.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
All ATmega161 I/Os and peripherals are placed in the I/O space. The I/O locations are
accessed by the IN and OUT instructions transferring data between the 32 general purpose working registers and the I/O space. I/O Registers within the address range $00 $1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the
value of single bits can be checked by using the SBIS and SBIC instructions. Refer to
the instruction set section for more details. When using the I/O specific commands IN
and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O Registers as
SRAM, $20 must be added to this address. All I/O Register addresses throughout this
document are shown with the SRAM address in parentheses.
For compatibility with future devices, reserved bits should be written to zero if accessed.
Reserved I/O memory addresses should never be written.
Some of the Status Flags are cleared by writing a logical “1” to them. Note that the CBI
and SBI instructions will operate on all bits in the I/O Register, writing a one back into
any flag read as set, thus clearing the Flag. The CBI and SBI instructions work with registers $00 to $1F only.
The I/O and Peripherals Control Registers are explained in the following sections.
Status Register – SREG
The AVR Status Register (SREG) at I/O space location $3F ($5F) is defined as:
Bit
7
6
5
4
3
2
1
0
$3F ($5F)
I
T
H
S
V
N
Z
C
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SREG
• Bit 7 – I: Global Interrupt Enable
The Global Interrupt Enable bit must be set (one) for the interrupts to be enabled. The
individual interrupt enable control is then performed in separate control registers. If the
Global Interrupt Enable bit is cleared (zero), none of the interrupts are enabled independent of the individual interrupt enable settings. The I-bit is cleared by hardware after an
interrupt has occurred and is set by the RETI instruction to enable subsequent
interrupts.
• Bit 6 – T: Bit Copy Storage
The Bit Copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T-bit as source
and destination for the operated bit. A bit from a register in the Register File can be copied into T by the BST instruction and a bit in T can be copied into a bit in a register in the
Register File by the BLD instruction.
• Bit 5 – H: Half Carry Flag
The Half Carry Flag H indicates a Half Carry in some arithmetic operations. See the
Instruction Set description for detailed information.
• Bit 4 – S: Sign Bit, S = N ⊕ V
The S-bit is always an exclusive or between the Negative Flag N and the Two’s Complement Overflow Flag V. See the Instruction Set description for detailed information.
• Bit 3 – V: Two’s Complement Overflow Flag
The Two’s Complement Overflow Flag V supports two’s complement arithmetics. See
the Instruction Set Description for detailed information.
21
1228D–AVR–02/07
• Bit 2 – N: Negative Flag
The Negative Flag N indicates a negative result after the different arithmetic and logic
operations. See the Instruction Set description for detailed information.
• Bit 1 – Z: Zero Flag
The Zero Flag Z indicates a zero result after the different arithmetic and logic operations. See the Instruction Set description for detailed information.
• Bit 0 – C: Carry Flag
The Carry Flag C indicates a carry in an arithmetic or logic operation. See the Instruction
Set description for detailed information.
Note that the Status Register is not automatically stored when entering an interrupt routine and restored when returning from an interrupt routine. This must be handled by
software.
Stack Pointer – SP
The ATmega161 Stack Pointer is implemented as two 8-bit registers in the I/O space
locations $3E ($5E) and $3D ($5D). As the ATmega161 supports up to 64-Kbyte memory, all 16 bits are used.
Bit
15
14
13
12
11
10
9
8
$3E ($5E)
SP15
SP14
SP13
SP12
SP11
SP10
SP9
SP8
SPH
$3D ($5D)
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
SPL
7
6
5
4
3
2
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
Initial Value
The Stack Pointer points to the data SRAM Stack area where the Subroutine and Interrupt Stacks are located. This Stack space in the data SRAM must be defined by the
program before any subroutine calls are executed or interrupts are enabled. The Stack
Pointer must be set to point above $60. The Stack Pointer is decremented by 1 when
data is pushed onto the Stack with the PUSH instruction, and it is decremented by 2
when an address is pushed onto the Stack with subroutine calls and interrupts. The
Stack Pointer is incremented by 1 when data is popped from the Stack with the POP
instruction, and it is incremented by 2 when an address is popped from the Stack with
return from subroutine RET or return from interrupt (RETI).
Reset and Interrupt
Handling
The ATmega161 provides 20 different interrupt sources. These interrupts and the separate Reset Vector each have a separate Program Vector in the Program memory space.
All interrupts are assigned individual enable bits that must be set (one) together with the
I-bit in the Status Register in order to enable the interrupt.
The lowest addresses in the Program memory space are automatically defined as the
Reset and Interrupt vectors. The complete list of Vectors is shown in Table 2. The list
also determines the priority levels of the different interrupts. The lower the address, the
higher the priority level. RESET has the highest priority, and next is INT0 (the External
Interrupt Request 0) and so on.
22
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 2. Reset and Interrupt Vectors(1)
Vector
No.
Program Address
Source
Interrupt Definition
1
$000
RESET
External Pin, Power-on Reset and
Watchdog Reset
2
$002
INT0
External Interrupt Request 0
3
$004
INT1
External Interrupt Request 1
4
$006
INT2
External Interrupt Request 2
5
$008
TIMER2 COMP
Timer/Counter2 Compare Match
6
$00a
TIMER2 OVF
Timer/Counter2 Overflow
7
$00c
TIMER1 CAPT
Timer/Counter1 Capture Event
8
$00e
TIMER1 COMPA
Timer/Counter1 Compare Match A
9
$010
TIMER1 COMPB
Timer/Counter1 Compare Match B
10
$012
TIMER1 OVF
Timer/Counter1 Overflow
11
$014
TIMER0 COMP
Timer/Counter0 Compare Match
12
$016
TIMER0 OVF
Timer/Counter0 Overflow
13
$018
SPI, STC
Serial Transfer Complete
14
$01a
UART0, RX
UART0, Rx Complete
15
$01c
UART1, RX
UART1, Rx Complete
16
$01e
UART0, UDRE
UART0 Data Register Empty
17
$020
UART1, UDRE
UART1 Data Register Empty
18
$022
UART0, TX
UART0, Tx Complete
19
$024
UART1, TX
UART1, Tx Complete
20
$026
EE_RDY
EEPROM Ready
21
$028
ANA_COMP
Analog Comparator
Note:
1. If BOOTRST fuse is programmed, the Reset Vector is located on program address
$1e00, see Table 39 on page 112 for details.
The most typical and general program setup for the Reset and Interrupt Vector
addresses are:
Address
Labels
Code
Comments
$000
jmp
RESET
; Reset Handler
$002
jmp
EXT_INT0
; IRQ0 Handler
$004
jmp
EXT_INT1
; IRQ1 Handler
$006
jmp
EXT_INT2
; IRQ2 Handler
$008
jmp
TIM2_COMP
; Timer2 Compare Handler
$00a
jmp
TIM2_OVF
; Timer2 Overflow Handler
$00c
jmp
TIM1_CAPT
; Timer1 Capture Handler
$00e
jmp
TIM1_COMPA
; Timer1 CompareA Handler
$010
jmp
TIM1_COMPB
; Timer1 CompareB Handler
$012
jmp
TIM1_OVF
$014
jmp
TIM0_COMP
$016
jmp
TIM0_OVF
; Timer0 Overflow Handler
$018
jmp
SPI_STC;
; SPI Transfer Complete Handler
; Timer1 Overflow Handler
; Timer0 Compare Handler
23
1228D–AVR–02/07
$01a
jmp
UART_RXC0
; UART0 RX Complete Handler
$01c
jmp
UART_RXC1
; UART1 RX Complete Handler
$01e
jmp
UART_DRE0
; UDR0 Empty Handler
$020
jmp
UART_DRE1
; UDR1 Empty Handler
$022
jmp
UART_TXC0
; UART0 TX Complete Handler
$024
jmp
UART_TXC1
; UART1 TX Complete Handler
$026
jmp
EE_RDY
; EEPROM Ready Handler
$028
jmp
ANA_COMP
; Analog Comparator Handler
;
$02a
MAIN:
ldi r16,high(RAMEND) ; Main program start
$02b
out SPH,r16
$02c
ldi r16,low(RAMEND)
$02d
out SPL,r16
$02e
…
<instr>
…
…
xxx
…
When the BOOTRST fuse is programmed, the most typical and general program setup
for the Reset and Interrupt Vector addresses are:
Address
Labels
Code
Comments
.org $002
; Reset is located at $1e000
$002
jmp
EXT_INT0
; IRQ0 Handler
$004
jmp
EXT_INT1
; IRQ1 Handler
$006
jmp
EXT_INT2
; IRQ2 Handler
$008
jmp
TIM2_COMP
; Timer2 Compare Handler
$00a
jmp
TIM2_OVF
; Timer2 Overflow Handler
$00c
jmp
TIM1_CAPT
; Timer1 Capture Handler
$00e
jmp
TIM1_COMPA
; Timer1 CompareA Handler
$010
jmp
TIM1_COMPB
; Timer1 CompareB Handler
$012
jmp
TIM1_OVF
; Timer1 Overflow Handler
$014
jmp
TIM0_COMP
; Timer0 Compare Handler
$016
jmp
TIM0_OVF
; Timer0 Overflow Handler
$018
jmp
SPI_STC;
; SPI Transfer Complete Handler
$01a
jmp
UART_RXC0
; UART0 RX Complete Handler
$01c
jmp
UART_RXC1
; UART1 RX Complete Handler
$01e
jmp
UART_DRE0
; UDR0 Empty Handler
$020
jmp
UART_DRE1
; UDR1 Empty Handler
$022
jmp
UART_TXC0
; UART0 TX Complete Handler
$024
jmp
UART_TXC1
; UART1 TX Complete Handler
$026
jmp
EE_RDY
; EEPROM Ready Handler
$028
jmp
ANA_COMP
; Analog Comparator Handler
;
$02a
MAIN:
ldi r16,high(RAMEND); Main program start
$02b
out SPH,r16
$02c
ldi r16,low(RAMEND)
$02d
out SPL,r16
$02e
<instr>
xxx
;
.org $1e00
$1e00
…
…
24
jmp
…
RESET
…
; Reset handler
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Reset Sources
The ATmega161 has three sources of Reset:
•
Power-on Reset. The MCU is reset when the supply voltage is below the Power-on
Reset threshold (VPOT).
•
External Reset. The MCU is reset when a low level is present on the RESET pin for
more than 500 ns.
•
Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and
the Watchdog is enabled.
During Reset, all I/O Registers are then set to their initial values and the program starts
execution from address $000. The instruction placed in address $000 must be a JMP
(relative jump) instruction to the reset handling routine. If the program never enables an
interrupt source, the Interrupt Vectors are not used and regular program code can be
placed at these locations. The circuit diagram in Figure 24 shows the Reset Logic. Table
3 and Table 4 define the timing and electrical parameters of the reset circuitry.
Figure 24. Reset Logic
DATA BUS
PORF
EXTRF
WDRF
MCU Status
Register (MCUSR)
CKSEL[2:0]
Delay Counters
Full
CK
25
1228D–AVR–02/07
Table 3. Reset Characteristics (VCC = 5.0V)(1)
Symbol
Parameter
Min
Typ
Max
Units
VPOT
Power-on Reset Threshold Voltage (rising)
1.0
1.4
1.8
V
Power-on Reset Threshold Voltage (falling)(1)
0.4
0.6
0.8
V
0.85 VCC
V
VRST
Note:
RESET Pin Threshold Voltage
1. The Power-on Reset will not work unless the supply voltage has been below VPOT
(falling).
‘
Table 4. Reset Delay Selections(3)
CKSEL
[2:0]
Start-up Time, VCC = 2.7V,
SUT Unprogrammed
Start-up Time, VCC = 4.0V,
SUT Programmed
Recommended
Usage(1)
000
4.2 ms + 6 CK
5.8 ms + 6 CK
External Clock, Fast
Rising Power
001
30 µs + 6 CK
10 µs + 6 CK
External Clock(2)
010
67 ms + 16K CK
92 ms + 16K CK
Crystal Oscillator,
Slowly Rising Power
011
4.2 ms + 16K CK
5.8 ms + 16K CK
Crystal Oscillator,
Fast Rising Power
100
30 µs + 16K CK
10 µs + 16K CK
Crystal Oscillator(2)
101
67 ms + 1K CK
92 ms + 1K CK
Ceramic
Resonator/External
Clock, Slowly Rising
Power
110
4.2 ms + 1K CK
5.8 ms + 1K CK
Ceramic Resonator,
Fast Rising Power
111
30 µs + 1K CK
10 µs + 1K CK
Ceramic
Resonator(2)
Notes:
1. The CKSEL fuses control only the start-up time. The Oscillator is the same for all
selections. On Power-up, the real-time part of the start-up time is increased with typ.
0.6 ms.
2. External Power-on Reset.
3. Table 4 shows the Start-up Times from Reset. From sleep, only the clock counting
part of the start-up time is used. The Watchdog Oscillator is used for timing the realtime part of the start-up time. The number WDT Oscillator cycles used for each timeout is shown in Table 5.
Table 5. Number of Watchdog Oscillator Cycles
SUT
Time-out
Number of Cycles
Unprogrammed
4.2 ms (at VCC = 2.7V)
1K
Unprogrammed
67 ms (at VCC = 2.7V)
16K
Programmed
5.8 ms (at VCC = 4.0V)
4K
Programmed
92 ms (at VCC = 4.0V)
64K
The frequency of the Watchdog Oscillator is voltage-dependent as shown in the Electrical Characteristics section. The device is shipped with CKSEL = 010.
26
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Power-on Reset
A Power-on Reset (POR) pulse is generated by an On-chip detection circuit. The detection level is nominally 1.4V (rising VCC). The POR is activated whenever VCC is below
the detection level. The POR circuit can be used to trigger the Start-up Reset, as well as
detect a failure in supply voltage.
A Power-on Reset (POR) circuit ensures that the device is reset from Power-on. Reaching the Power-on Reset threshold voltage invokes a delay counter, which determines
the delay, for which the device is kept in RESET after VCC rise. The time-out period of
the delay counter can be defined by the user through the CKSEL fuses. The eight different selections for the delay period are presented in Table 4. The RESET signal is
activated again, without any delay, when the VCC decreases below detection level.
Figure 25. MCU Start-up, RESET Tied to VCC
VCC
RESET
VPOT
VRST
tTOUT
TIME-OUT
INTERNAL
RESET
Figure 26. MCU Start-up, RESET Controlled Externally
VCC
RESET
TIME-OUT
VPOT
VRST
tTOUT
INTERNAL
RESET
27
1228D–AVR–02/07
External Reset
An External Reset is generated by a low level on the RESET pin. Reset pulses longer
than 500 ns will generate a Reset, even if the clock is not running. Shorter pulses are
not guaranteed to generate a Reset. When the applied signal reaches the Reset
Threshold Voltage (VRST) on its positive edge, the delay timer starts the MCU after the
Time-out period (tTOUT) has expired.
Figure 27. External Reset during Operation
Watchdog Reset
When the Watchdog times out, it will generate a short reset pulse of 1 XTAL cycle duration. On the falling edge of this pulse, the delay timer starts counting the Time-out period
(tTOUT). Refer to page 58 for details on operation of the Watchdog.
Figure 28. Watchdog Reset during Operation
28
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
MCU Status Register –
MCUSR
The MCU Status Register provides information on which reset source caused an MCU
Reset.
Bit
7
6
5
4
3
2
1
0
$34 ($54)
–
–
–
–
WDRF
–
EXTRF
PORF
Read/Write
R
R
R
R
R/W
R
R/W
R/W
Initial Value
0
0
0
0
MCUSR
See Bit Description
• Bits 7..4 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a Watchdog Reset occurs. The bit is cleared by a Power-on Reset or by
writing a logical “0” to the Flag.
• Bit 2 – Res: Reserved Bit
This bit are reserved bit in the ATmega161 and always read as zero.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is cleared by a Power-on Reset or by
writing a logical “0” to the Flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is cleared only by writing a logical “0”
to the Flag.
To make use of the Reset Flags to identify a reset condition, the user should read and
then clear the MCUSR as early as possible in the program. If the register is cleared
before another reset occurs, the source of the reset can be found by examining the
Reset Flags.
Interrupt Handling
The ATmega161 has two 8-bit Interrupt Mask Control Registers; GIMSK (General Interrupt Mask Register) and TIMSK (Timer/Counter Interrupt Mask Register).
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared (zero) and all interrupts are disabled. The user software can set (one) the I-bit to enable nested interrupts.
The I-bit is set (one) when a Return from Interrupt instruction (RETI) is executed.
When the Program Counter is vectored to the actual Interrupt Vector in order to execute
the interrupt handling routine, hardware clears the corresponding flag that generated the
interrupt. Some of the Interrupt Flags can also be cleared by writing a logical “1” to the
Flag bit position(s) to be cleared.
If an interrupt condition occurs when the corresponding interrupt enable bit is cleared
(zero), the Interrupt Flag will be set and remembered until the interrupt is enabled or the
Flag is cleared by software.
If one or more interrupt conditions occur when the global interrupt enable bit is cleared
(zero), the corresponding Interrupt Flag(s) will be set and remembered until the global
interrupt enable bit is set (one), and will be executed by order of priority.
Note that external level interrupt does not have a flag and will only be remembered for
as long as the interrupt condition is present.
29
1228D–AVR–02/07
Note that the Status Register is not automatically stored when entering an interrupt routine or restored when returning from an interrupt routine. This must be handled by
software.
Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles
minimum. After four clock cycles, the Program Vector address for the actual interrupt
handling routine is executed. During this four-clock-cycle period, the Program Counter
(13 bits) is pushed onto the Stack. The Vector is normally a jump to the interrupt routine,
and this jump takes three clock cycles. If an interrupt occurs during execution of a multicycle instruction, this instruction is completed before the interrupt is served. If an interrupt occurs when the MCU is in Sleep mode, the interrupt execution response time is
increased by four clock cycles.
A return from an interrupt handling routine takes four clock cycles. During these four
clock cycles, the Program Counter (2 bytes) is popped back from the Stack, the Stack
Pointer is incremented by 2, and the I-Flag in SREG is set. When AVR exits from an
interrupt, it will always return to the main program and execute one more instruction
before any pending interrupt is served.
General Interrupt Mask
Register – GIMSK
Bit
7
6
5
4
3
2
1
0
$3B ($5B)
INT1
INT0
INT2
–
–
–
–
–
Read/Write
R/W
R/W
R
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
GIMSK
• Bit 7 – INT1: External Interrupt Request 1 Enable
When the INT1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),
the external pin interrupt is enabled. The Interrupt Sense Control1 bits 1/0 (ISC11 and
ISC10) in the MCU general Control Register (MCUCR) define whether the external
interrupt is activated on rising and/or falling edge of the INT1 pin or is level-sensed.
Activity on the pin will cause an interrupt request even if INT1 is configured as an output.
The corresponding interrupt of External Interrupt Request 1 is executed from Program
memory address $004. See also “External Interrupts”.
• Bit 6 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),
the external pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and
ISC00) in the MCU general Control Register (MCUCR) define whether the external
interrupt is activated on rising and/or falling edge of the INT0 pin or is level-sensed.
Activity on the pin will cause an interrupt request even if INT0 is configured as an output.
The corresponding interrupt of External Interrupt Request 0 is executed from Program
memory address $002. See also “External Interrupts.”
• Bit 5 – INT2: External Interrupt Request 2 Enable
When the INT2 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),
the external pin interrupt is activated. The Interrupt Sense Control2 bit (ISC02 in the
Extended MCU Control Register [EMCUCR]) defines whether the external interrupt is
activated on rising or falling edge of the INT2 pin. Activity on the pin will cause an interrupt request even if INT2 is configured as an output. The corresponding interrupt of
External Interrupt Request 2 is executed from Program memory address $006. See also
“External Interrupts.”
30
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Bits 4..0 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
General Interrupt Flag
Register – GIFR
Bit
7
6
5
4
3
2
1
0
$3A ($5A)
INTF1
INTF0
INTF2
–
–
–
–
–
Read/Write
R/W
R/W
R/W
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
GIFR
• Bit 7 – INTF1: External Interrupt Flag1
When an event on the INT1 pin triggers an interrupt request, INTF1 becomes set (one).
If the I-bit in SREG and the INT1 bit in GIMSK are set (one), the MCU will jump to the
Interrupt Vector at address $004. The Flag is cleared when the interrupt routine is executed. Alternatively, the Flag can be cleared by writing a logical “1” to it.
• Bit 6 – INTF0: External Interrupt Flag0
When an event on the INT0 pin triggers an interrupt request, INTF0 becomes set (one).
If the I-bit in SREG and the INT0 bit in GIMSK are set (one), the MCU will jump to the
Interrupt Vector at address $002. The Flag is cleared when the interrupt routine is executed. Alternatively, the Flag can be cleared by writing a logical “1” to it.
• Bit 5 – INTF2: External Interrupt Flag2
When an event on the INT2 pin triggers an interrupt request, INTF2 becomes set (one).
If the I-bit in SREG and the INT2 bit in GIMSK are set (one), the MCU will jump to the
Interrupt Vector at address $006. The Flag is cleared when the interrupt routine is executed. Alternatively, the Flag can be cleared by writing a logical “1” to it.
• Bits 4..0 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
Timer/Counter Interrupt Mask
Register – TIMSK
Bit
7
6
5
4
3
2
1
0
TOIE1
OCIE1A
OCIE1B
TOIE2
TICIE1
OCIE2
TOIE0
OCIE0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$39 ($59)
TIMSK
• Bit 7 – TOIE1: Timer/Counter1 Overflow Interrupt Enable
When the TOIE1 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Overflow interrupt is enabled. The corresponding interrupt (at Vector
$012) is executed if an overflow in Timer/Counter1 occurs, i.e., when the TOV1 bit is set
in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 6 – OCE1A: Timer/Counter1 Output CompareA Match Interrupt Enable
When the OCIE1A bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 CompareA Match interrupt is enabled. The corresponding interrupt (at
Vector $00e) is executed if a Compare A Match in Timer/Counter1 occurs, i.e., when the
OCF1A bit is set in the Timer/Counter Interrupt Flag Register (TIFR).
31
1228D–AVR–02/07
• Bit 5 – OCIE1B: Timer/Counter1 Output CompareB Match Interrupt Enable
When the OCIE1B bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 CompareB Match interrupt is enabled. The corresponding interrupt (at
Vector $010) is executed if a Compare B Match in Timer/Counter1 occurs, i.e., when the
OCF1B bit is set in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 4 – TOIE2: Timer/Counter2 Overflow Interrupt Enable
When the TOIE2 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter2 Overflow interrupt is enabled. The corresponding interrupt (at Vector
$00a) is executed if an overflow in Timer/Counter2 occurs, i.e., when the TOV2 bit is set
in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 3 – TICIE1: Timer/Counter1 Input Capture Interrupt Enable
When the TICIE1 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Input Capture Event Interrupt is enabled. The corresponding interrupt
(at Vector $00C) is executed if a capture-triggering event occurs on pin 31, ICP, i.e.,
when the ICF1 bit is set in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 2 – OCIE2: Timer/Counter2 Output Compare Match Interrupt Enable
When the OCIE2 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter2 Compare Match interrupt is enabled. The corresponding interrupt (at
Vector $008) is executed if a Compare2 match in Timer/Counter2 occurs, i.e., when the
OCF2 bit is set in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 1 – TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt (at Vector
$016) is executed if an overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set
in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 0 – OCIE0: Timer/Counter0 Output Compare Match Interrupt Enable
When the OCIE0 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter0 Compare Match interrupt is enabled. The corresponding interrupt (at
Vector $014) is executed if a Compare 0 Match in Timer/Counter0 occurs, i.e., when the
OCF0 bit is set in the Timer/Counter Interrupt Flag Register (TIFR).
32
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Timer/Counter Interrupt Flag
Register – TIFR
Bit
7
6
5
4
3
2
1
0
$38 ($58)
TOV1
OCF1A
OCIFB
TOV2
ICF1
OCF2
TOV0
OCF0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TIFR
• Bit 7 – TOV1: Timer/Counter1 Overflow Flag
The TOV1 is set (one) when an overflow occurs in Timer/Counter1. TOV1 is cleared by
hardware when executing the corresponding Interrupt Handling Vector. Alternatively,
TOV1 is cleared by writing a logical “1” to the Flag. When the I-bit in SREG, and TOIE1
(Timer/Counter1 Overflow Interrupt Enable), and TOV1 are set (one), the
Timer/Counter1 Overflow Interrupt is executed. In PWM mode, this bit is set when
Timer/Counter1 changes counting direction at $0000.
• Bit 6 – OCF1A: Output Compare Flag 1A
The OCF1A bit is set (one) when a compare match occurs between the Timer/Counter1
and the data in OCR1A (Output Compare Register 1A). OCF1A is cleared by hardware
when executing the corresponding Interrupt Handling Vector. Alternatively, OCF1A is
cleared by writing a logical “1” to the Flag. When the I-bit in SREG and OCIE1A
(Timer/Counter1 Compare Match Interrupt A Enable) and OCF1A are set (one), the
Timer/Counter1 Compare A Match Interrupt is executed.
• Bit 5 – OCF1B: Output Compare Flag 1B
The OCF1B bit is set (one) when a compare match occurs between the Timer/Counter1
and the data in OCR1B (Output Compare Register 1B). OCF1B is cleared by hardware
when executing the corresponding Interrupt Handling Vector. Alternatively, OCF1B is
cleared by writing a logical “1” to the Flag. When the I-bit in SREG and OCIE1B
(Timer/Counter1 Compare Match Interrupt B Enable) and OCF1B are set (one), the
Timer/Counter1 Compare B Match Interrupt is executed.
• Bit 4 – TOV2: Timer/Counter2 Overflow Flag
The bit TOV2 is set (one) when an overflow occurs in Timer/Counter2. TOV2 is cleared
by hardware when executing the corresponding Interrupt Handling Vector. Alternatively,
TOV2 is cleared by writing a logical “1” to the Flag. When the SREG I-bit and TOIE2
(Tim er/Co un ter2 Ove rflow Inte rrup t En able) an d TO V2 a re set (o ne) , th e
Timer/Counter2 Overflow interrupt is executed.
• Bit 3 – ICF1: Input Capture Flag 1
The ICF1 bit is set (one) to flag an Input Capture Event, indicating that the
Timer/Counter1 value has been transferred to the Input Capture Register (ICR1). ICF1
is cleared by hardware when executing the corresponding Interrupt Handling Vector.
Alternatively, ICF1 is cleared by writing a logical “1” to the Flag. When the SREG I-bit
and TICIE1 (Timer/Counter1 Input Capture Interrupt Enable) and ICF1 are set (one), the
Timer/Counter1 Capture Interrupt is executed.
• Bit 2 – OCF2: Output Compare Flag 2
The OCF2 bit is set (one) when a Compare Match occurs between the Timer/Counter2
and the data in OCR2 (Output Compare Register 2). OCF2 is cleared by hardware when
executing the corresponding Interrupt Handling Vector. Alternatively, OCF2 is cleared
by writing a logical “1” to the Flag. When the I-bit in SREG and OCIE2 (Timer/Counter2
33
1228D–AVR–02/07
Compare match InterruptA Enable) and the OCF2 are set (one), the Timer/Counter2
Compare match Interrupt is executed.
• Bit 1 – TOV0: Timer/Counter0 Overflow Flag
The bit TOV0 is set (one) when an overflow occurs in Timer/Counter0. TOV0 is cleared
by hardware when executing the corresponding Interrupt Handling Vector. Alternatively,
TOV0 is cleared by writing a logical “1” to the Flag. When the SREG I-bit and TOIE0
(Tim er/Co un ter0 Ove rflow Inte rrup t En able) an d TO V0 a re set (o ne) , th e
Timer/Counter0 Overflow interrupt is executed.
• Bit 2 – OCF0: Output Compare Flag 0
The OCF0 bit is set (one) when compare match occurs between the Timer/Counter0
and the data in OCR0 (Output Compare Register 0). OCF0 is cleared by hardware when
executing the corresponding Interrupt Handling Vector. Alternatively, OCF0 is cleared
by writing a logical “1” to the Flag. When the I-bit in SREG and OCIE0 (Timer/Counter0
Compare match InterruptA Enable) and the OCF0 are set (one), the Timer/Counter0
Compare match Interrupt is executed.
External Interrupts
The external interrupts are triggered by the INT0, INT1, and INT2 pins. Observe that, if
enabled, the interrupts will trigger even if the INT0/INT1/INT2 pins are configured as outputs. This feature provides a way of generating a software interrupt. The external
interrupts can be triggered by a falling or rising edge or a low level (INT2 is only an edge
triggered interrupt). This is set up as indicated in the specification for the MCU Control
Register – MCUCR (INT0/INT1) and EMCUCR (INT2). When the external interrupt is
enabled and is configured as level triggered (only INT0/INT1), the interrupt will trigger as
long as the pin is held low.
MCU Control Register –
MCUCR
The MCU Control Register contains control bits for general MCU functions.
Bit
7
6
5
4
3
2
1
0
$35 ($55)
SRE
SRW10
SE
SM1
ISC11
ISC10
ISC01
ISC00
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
MCUCR
• Bit 7 – SRE: External SRAM Enable
When the SRE bit is set (one), the external Data memory interface is enabled and the
pin functions AD0 - 7 (Port A), A8 - 5 (Port C), ALE (Port E), WR, and RD (Port D) are
activated as the alternate pin functions. The SRE bit overrides any pin direction settings
in the respective Data Direction Registers. See Figure 50 through Figure 53 for a
description of the external memory pin functions. When the SRE bit is cleared (zero),
the external Data memory interface is disabled and the normal pin and data direction
settings are used.
• Bit 6 – SRW10: External SRAM Wait State
The SRW10 bit is used to set up extra wait states in the external memory interface. See
“Double-speed Transmission” on page 78 for a detailed description.
• Bit 5 – SE: Sleep Enable
The SE bit must be set (one) to make the MCU enter the Sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the Sleep mode unless it is the pro-
34
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
grammer’s purpose, it is recommended to set the Sleep Enable (SE) bit just before the
execution of the SLEEP instruction.
• Bit 4 – SM1: Sleep Mode Select Bit 1
The SM1 bit, together with the SM0 control bit in EMCUCR, selects between the three
available Sleep modes as shown in Table 6.
Table 6. Sleep Mode Select
SM1
SM0
Sleep Mode
0
0
Idle
0
1
Reserved
1
0
Power-down
1
1
Power-save
• Bits 3, 2 – ISC11, ISC10: Interrupt Sense Control 1 Bit 1 and Bit 0
The External Interrupt 1 is activated by the external pin INT1 if the SREG I-Flag and the
corresponding interrupt mask in the GIMSK are set. The level and edges on the external
INT1 pin that activate the interrupt are defined in Table 7. The value on the INT1 pin is
sampled before detecting edges. If edge or toggle interrupt is selected, pulses that last
longer than one clock period will generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low-level interrupt is selected, the low level must be held
until the completion of the currently executing instruction to generate an interrupt.
Table 7. Interrupt 1 Sense Control
ISC11
ISC10
Description
0
0
The low level of INT1 generates an interrupt request.
0
1
Any logical change on INT1 generates an interrupt request.
1
0
The falling edge of INT1 generates an interrupt request.
1
1
The rising edge of INT1 generates an interrupt request.
• Bits 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0
The External Interrupt 0 is activated by the external pin INT0 if the SREG I-Flag and the
corresponding interrupt mask is set. The level and edges on the external INT0 pin that
activate the interrupt are defined in Table 8. The value on the INT0 pin is sampled
before detecting edges. If edge or toggle interrupt is selected, pulses that last longer
than one clock period will generate an interrupt. Shorter pulses are not guaranteed to
generate an interrupt. If low-level interrupt is selected, the low level must be held until
the completion of the currently executing instruction to generate an interrupt.
Table 8. Interrupt 0 Sense Control
ISC01
ISC00
Description
0
0
The low level of INT0 generates an interrupt request.
0
1
Any logical change on INT0 generates an interrupt request.
1
0
The falling edge of INT0 generates an interrupt request.
1
1
The rising edge of INT0 generates an interrupt request.
35
1228D–AVR–02/07
Extended MCU Control
Register – EMCUCR
The Extended MCU Control Register contains control bits for External Interrupt 2, Sleep
mode bit and control bits for the external memory interface.
Bit
7
6
5
4
3
2
1
0
$36 ($56)
SM0
SRL2
SRL1
SRL0
SRW01
SRW00
SRW11
ISC2
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
EMCUCR
• Bit 7 – SM0: Sleep Mode Bit 0
When this bit is set (one) and Sleep mode bit 1 (SM1) in MCUCR is set, Power-save
mode is selected as Sleep mode. Refer to page 36 for a detailed description of the
Sleep modes.
• Bits 6..4 – SRL2, SRL1, SRL0: External SRAM Limit
It is possible to configure different wait states for different external memory addresses in
ATmega161. The SRL2 - SRL0 bits are used to define at which address the different
wait states will be configured. See “Interface to External Memory” on page 84 for a
detailed description.
• Bits 3..1 – SRW01, SRW00, SRW11: External SRAM Wait State Select Bits
The SRW01, SRW00 and SRW11 bits are used to set up extra wait states in the external memory interface. See “Interface to External Memory” on page 84 for a detailed
description.
• Bit 0 – ISC2: Interrupt Sense Control 2
The external interrupt 2 is activated by the external pin INT2 if the SREG I-Flag and the
corresponding interrupt mask in the GIMSK are set. If ISC2 is cleared (zero), a falling
edge on INT2 activates the interrupt. If ISC2 is set (one), a rising edge on INT2 activates
the interrupt. Edges on INT2 are registered asynchronously. Pulses on INT2 wider than
50 ns will generate an interrupt. Shorter pulses are not guaranteed to generate an
interrupt.
When changing the ISC2 bit, an interrupt can occur. Therefore, it is recommended to
first disable INT2 by clearing its Interrupt Enable bit in the GIMSK Register. Then, ISC2
bit can be changed. Finally, the INT2 Interrupt Flag should be cleared by writing a logical
“1” to its Interrupt Flag bit in the GIFR Register before the interrupt is re-enabled.
Sleep Modes
To enter any of the three Sleep modes, the SE bit in MCUCR must be set (one) and a
SLEEP instruction must be executed. The SM1 bit in the MCUCR Register and SM0 bit
in the EMCUCR Register select which Sleep mode (Idle, Power-down or Power-save)
will be activated by the SLEEP instruction (see Table 6). If an enabled interrupt occurs
while the MCU is in a Sleep mode, the MCU awakes. The CPU is then halted for four
cycles, it executes the interrupt routine, and resumes execution from the instruction following SLEEP. The contents of the Register File, SRAM and I/O memory are unaltered.
If a reset occurs during Sleep mode, the MCU wakes up and executes from the Reset
Vector.
Idle Mode
When the SM1/SM0 bits are set to 00, the SLEEP instruction makes the MCU enter the
Idle mode, stopping the CPU but allowing SPI, UARTs, Analog Comparator,
Timer/Counters, Watchdog, and the Interrupt System to continue operating. This
enables the MCU to wake up from external triggered interrupts as well as internal ones
like the Timer Overflow and UART Receive Complete interrupts. If wake-up from the
36
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Analog Comparator interrupt is not required, the Analog Comparator can be powered
down by setting the ACD bit in the Analog Comparator Control and Status Register
(ACSR). This will reduce power consumption in Idle mode.
Power-down Mode
When the SM1/SM0 bits are set to 10, the SLEEP instruction makes the MCU enter the
Power-down mode. In this mode, the external Oscillator is stopped while the external
interrupts and the Watchdog (if enabled) continue operating. Only an External Reset, a
Watchdog Reset (if enabled), an external level interrupt on INT0 or INT1, or an external
edge interrupt on INT2 can wake up the MCU.
If INT2 is used for wake-up from Power-down mode, the edge is remembered until the
MCU wakes up.
If a level-triggered interrupt is used for wake-up from Power-down mode, the changed
level must be held for some time to wake up the MCU. This makes the MCU less sensitive to noise. The changed level is sampled twice by the Watchdog Oscillator clock, and
if the input has the required level during this time, the MCU will wake up. The period of
the Watchdog Oscillator is 1 µs (nominal) at 5.0V and 25°C. The frequency of the
Watchdog Oscillator is voltage-dependent as shown in the Electrical Characteristics
section.
When waking up from Power-down mode, a delay from the wake-up condition occurs
until the wake-up becomes effective. This allows the clock to restart and become stable
after having been stopped. The wake-up period is defined by the same CKSEL fuses
that define the Reset Time-out period. The wake-up period is equal to the clock counting
part of the reset period, as shown in Table 4. If the wake-up condition disappears before
the MCU wakes up and starts to execute, e.g., a low level on INT0 is not held long
enough, the interrupt causing the wake-up will not be executed.
Power-save Mode
When the SM1/SM0 bits are 11, the SLEEP instruction makes the MCU enter the
Power-save mode. This mode is identical to Power-down, with one exception.
If Timer/Counter2 is clocked asynchronously, i.e., the AS2 bit in ASSR is set,
Timer/Counter2 will run during sleep. In addition to the Power-down wake-up sources,
the device can also wake up from either Timer Overflow or Output Compare event from
Timer/Counter2 if the corresponding Timer/Counter2 interrupt enable bits are set in
TIMSK and the global interrupt enable bit in SREG is set.
If the asynchronous timer is not clocked asynchronously, Power-down mode is recommended instead of Power-save mode because the contents of the register in the
asynchronous timer should be considered undefined after wake-up in Power-save mode
even if AS2 is 0.
37
1228D–AVR–02/07
Timer/Counters
The ATmega161 provides three general purpose Timer/Counters – two 8-bit T/Cs and
one 16-bit T/C. Timer/Counter2 can optionally be asynchronously clocked from an external Oscillator. This Oscillator is optimized for use with a 32.768 kHz watch crystal,
enabling use of Timer/Counter2 as a Real-time Clock (RTC). Timer/Counters 0 and 1
have individual prescaling selection from the same 10-bit prescaling timer.
Timer/Counter2 has its own prescaler. Both these prescalers can be Reset by setting
the corresponding control bits in the Special Functions IO Register (SFIOR). Refer to
page 39 for a detailed description. These Timer/Counters can either be used as a timer
with an internal clock time base or as a counter with an external pin connection, which
triggers the counting.
Timer/Counter
Prescalers
Figure 29. Prescaler for Timer/Counter0 and 1
Clear
PSR10
TCK1
TCK0
For Timer/Counters 0 and 1, the four prescaled selections are: CK/8, CK/64, CK/256,
and CK/1024, where CK is the Oscillator clock. For the two Timer/Counters 0 and 1, CK,
external source and stop can also be selected as clock sources. Setting the PSR10 bit
in SFIOR Resets the prescaler. This allows the user to operate with a predictable prescaler. Note that Timer/Counter1 and Timer/Counter0 share the same prescaler and a
Prescaler Reset will affect both Timer/Counters.
38
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 30. Timer/Counter2 Prescaler
CK
PCK2
PSR2
PCK2/1024
PCK2/256
PCK2/128
PCK2/32
PCK2/8
AS2
PCK2/64
10-BIT T/C PRESCALER
Clear
TOSC1
0
CS20
CS21
CS22
TIMER/COUNTER2 CLOCK SOURCE
TCK2
The clock source for Timer/Counter2 prescaler is named PCK2. PCK2 is by default connected to the main system clock (CK). By setting the AS2 bit in ASSR, Timer/Counter2
is asynchronously clocked from the PD4(TOSC1) pin. This enables use of
Timer/Counter2 as a Real-time Clock (RTC). When AS2 is set, pins PD4(TOSC1) and
PD5(TOSC2) are disconnected from Port D. A crystal can then be connected between
the PD4(TOSC1) and PD5(TOSC2) pins to serve as an independent clock source for
Timer/Counter2. The Oscillator is optimized for use with a 32.768 kHz crystal. Alternatively, an external clock signal can be applied to PD4(TOSC1). The frequency of this
clock must be lower than one fourth of the CPU clock and not higher than 256 kHz. Setting the PSR2 bit in SFIOR Resets the prescaler. This allows the user to operate with a
predictable prescaler.
Special Function IO Register –
SFIOR
Bit
7
6
5
4
3
2
1
0
$30 ($50)
–
–
–
–
–
–
PSR2
PSR10
Read/Write
R
R
R
R
R
R
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SFIOR
• Bits 7..2 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
• Bit 1 – PSR2: Prescaler Reset Timer/Counter2
When this bit is set (one), the Timer/Counter2 prescaler will be reset. The bit will be
cleared by hardware after the operation is performed. Writing a zero to this bit will have
no effect. This bit will always be read as zero if Timer/Counter2 is clocked by the internal
CPU clock. If this bit is written when Timer/Counter2 is operating in asynchronous
mode, however, the bit will remain as one until the prescaler has been reset. See “Asynchronous Operation of Timer/Counter2” on page 48 for a detailed description of
asynchronous operation.
39
1228D–AVR–02/07
• Bit 0 – PSR10: Prescaler Reset Timer/Counter1 and Timer/Counter0
When this bit is set (one), the Timer/Counter1 and Timer/Counter0 prescaler will be
reset. The bit will be cleared by hardware after the operation is performed. Writing a
zero to this bit will have no effect. Note that Timer/Counter1 and Timer/Counter0 share
the same prescaler and a reset of this prescaler will affect both timers. This bit will
always be read as zero.
8-bit Timer/Counters
T/C0 and T/C2
Figure 31 shows the block diagram for Timer/Counter0. Figure 32 shows the block diagram for Timer/Counter2.
Figure 31. Timer/Counter0 Block Diagram
7
0
TIMER/COUNTER0
(TCNT0)
7
PSR2
PSR10
SPECIAL FUNCTIONS
IO REGISTER (SFIOR)
CS00
CS02
CS01
CTC0
COM01
COM00
FOC0
PWM0
TOV0
T/C0 CONTROL
REGISTER (TCCR0)
OCF0
ICF1
OCF2
TOV2
OCF1B
TOV1
TIMER INT. FLAG
REGISTER (TIFR)
OCF1A
TIMER INT. MASK
REGISTER (TIMSK)
OCF0
TOV0
OCIE0
OCIE2
TOIE0
TICIE1
OCIE1B
TOIE2
TOIE1
8-BIT DATA BUS
OCIE1A
T/C0 OVER- T/C0 COMPARE
FLOW IRQ
MATCH IRQ
T/C CLEAR
T/C CLK SOURCE
UP/DOWN
CONTROL
LOGIC
CK
T0
0
8-BIT COMPARATOR
7
0
OUTPUT COMPARE
REGISTER0 (OCR0)
40
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 32. Timer/Counter2 Block Diagram
T/C2 OVER- T/C2 COMPARE
FLOW IRQ
MATCH IRQ
8-BIT DATA BUS
0
TIMER/COUNTER2
(TCNT2)
PSR2
PSR10
CS20
CS22
CS21
CTC2
COM21
COM20
FOC2
PWM2
TOV0
OCF0
ICF1
OCF2
TOV2
OCF1B
SPECIAL FUNCTIONS
IO REGISTER (SFIOR)
T/C2 CONTROL
REGISTER (TCCR2)
TIMER INT. FLAG
REGISTER (TIFR)
TOV1
7
TOV2
OCF2
TIMER INT. MASK
REGISTER (TIMSK)
OCF1A
TOIE0
OCIE0
OCIE2
TICIE1
OCIE1B
TOIE2
TOIE1
OCIE1A
8-BIT ASYNCH T/C2 DATA BUS
T/C CLEAR
T/C CLK SOURCE
UP/DOWN
CK
CONTROL
LOGIC
TOSC1
7
0
8-BIT COMPARATOR
0
OUTPUT COMPARE
REGISTER2 (OCR2)
CK
TCK2
ICR2UB
TC2UB
AS2
ASYNCH. STATUS
REGISTER (ASSR)
OCR2UB
7
SYNCH UNIT
The 8-bit Timer/Counter0 can select clock source from CK, prescaled CK or an external
pin.The 8-bit Timer/Counter2 can select clock source from CK, prescaled CK or external
TOSC1.
Both Timer/Counters can be stopped as described in sections “Timer/Counter0 Control
Register – TCCR0” and “Timer/Counter2 Control Register – TCCR2”.
The various Status Flags (Overflow and Compare Match) are found in the
Timer/Counter Interrupt Flag Register (TIFR). Control signals are found in the
Timer/Counter Control Register (TCCR0 and TCCR2). The interrupt enable/disable settings are found in the Timer/Counter Interrupt Mask Register (TIMSK).
When Timer/Counter0 is externally clocked, the external signal is synchronized with the
Oscillator frequency of the CPU. To assure proper sampling of the external clock, the
minimum time between two external clock transitions must be at least one internal CPU
clock period. The external clock signal is sampled on the rising edge of the internal CPU
clock.
The 8-bit Timer/Counters feature both a high resolution and a high accuracy usage with
the lower prescaling opportunities. Similarly, the high prescaling opportunities make the
Timer/Counter0 useful for lower speed functions or exact timing functions with infrequent actions.
Timer/Counters 0 and 2 can also be used as 8-bit Pulse Width Modulators. In this
mode, the Timer/Counter and the Output Compare Register serve as a glitch-free,
stand-alone PWM with centered pulses. Refer to page 44 for a detailed description of
this function.
41
1228D–AVR–02/07
Timer/Counter0 Control
Register – TCCR0
Bit
7
6
5
4
3
2
1
0
FOC0
PWM0
COM01
COM00
CTC0
CS02
CS01
CS00
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$33 ($53)
Timer/Counter2 Control
Register – TCCR2
Bit
7
6
5
4
3
2
1
0
FOC2
PWM2
COM21
COM20
CTC2
CS22
CS21
CS20
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$27 ($47)
TCCR0
TCCR2
• Bit 7 – FOC0/FOC2: Force Output Compare
Writing a logical “1” to this bit forces a change in the compare match output pin PB0
(Timer/Counter0) and PB1 (Timer/Counter2) according to the values already set in
COMn1 and COMn0. If the COMn1 and COMn0 bits are written in the same cycle as
FOC0/FOC2, the new settings will not take effect until the next compare match or
Forced Output Compare Match occurs. The Force Output Compare bit can be used to
change the output pin without waiting for a compare match in the timer. The automatic
action programmed in COMn1 and COMn0 happens as if a Compare Match had
occurred, but no interrupt is generated and the Timer/Counters will not be cleared even
if CTC0/CTC2 is set. The FOC0/FOC2 bits will always be read as zero. The setting of
the FOC0/FOC2 bits has no effect in PWM mode.
• Bit 6 – PWM0/PWM2: Pulse Width Modulator Enable
When set (one), this bit enables PWM mode for Timer/Counter0 or Timer/Counter2.
This mode is described on page 44.
• Bits 5, 4 – COM01, COM00/COM21, COM20: Compare Output Mode, Bits 1 and 0
The COMn1 and COMn0 control bits determine any output pin action following a compare match in Timer/Counter0 or Timer/Counter2. Output pin actions affect pins
PB0(OC0) or PB1(OC2). This is an alternative function to an I/O port and the corresponding direction control bit must be set (one) to control an output pin. The control
configuration is shown in Table 9.
Table 9. Compare Mode Select(1)(2)
COMn1
COMn0
0
0
Timer/Counter disconnected from output pin OCn.
0
1
Toggle the OCn output line.
1
0
Clear the OCn output line (to zero).
1
1
Set the OCn output line (to one).
Notes:
Description
1. In PWM mode, these bits have a different function. Refer to Table 12 for a detailed
description.
2. n = 0 or 2
• Bit 3 – CTC0/CTC2: Clear Timer/Counter on Compare Match
When the CTC0 or CTC2 control bit is set (one), Timer/Counter0 or Timer/Counter2 is
reset to $00 in the CPU clock cycle after a compare match. If the control bit is cleared,
the Timer/Counter continues counting and is unaffected by a compare match. When a
42
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
prescaling of 1 is used, and the compare register is set to C, the timer will count as follows if CTC0/CTC2 is set:
... | C-1 | C | 0 | 1 | ...
When the prescaler is set to divide by 8, the timer will count like this:
... | C-1, C-1, C-1, C-1, C-1, C-1, C-1, C-1 | C, C, C, C, C, C, C, C | 0, 0, 0, 0, 0, 0, 0, 0 |
1, 1, 1, ...
In PWM mode, this bit has a different function. If the CTC0 or CTC2 bit is cleared in
PWM mode, the Timer/Counter acts as an up/down counter. If the CTC0 or CTC2 bit is
set (one), the Timer/Counter wraps when it reaches $FF. Refer to page 44 for a detailed
description.
• Bits 2, 1, 0 – CS02, CS01, CS00/CS22, CS21, CS20: Clock Select Bits 2, 1 and 0
The Clock Select bits 2, 1, and 0 define the prescaling source of Timer/Counter0 and
Timer/Counter2.
Table 10. Clock 0 Prescale Select
CS02
CS01
CS00
Description
0
0
0
Stop, the Timer/Counter0 is stopped.
0
0
1
CK
0
1
0
CK/8
0
1
1
CK/64
1
0
0
CK/256
1
0
1
CK/1024
1
1
0
External Pin PB0(T0), falling edge
1
1
1
External Pin PB0(T0), rising edge
Table 11. Clock 2 Prescale Select
CS22
CS21
CS20
Description
0
0
0
Stop, the Timer/Counter2 is stopped.
0
0
1
PCK2
0
1
0
PCK2/8
0
1
1
PCK2/32
1
0
0
PCK2/64
1
0
1
PCK2/128
1
1
0
PCK2/256
1
1
1
PCK2/1024
The Stop condition provides a Timer Enable/Disable function. The prescaled modes are
scaled directly from the CK Oscillator clock for Timer/Counter0 and PCK2 for
Timer/Counter2. If the external pin modes are used for Timer/Counter0, transitions on
PB0/(T0) will clock the counter even if the pin is configured as an output. This feature
can give the user software control of the counting.
43
1228D–AVR–02/07
Timer Counter0 – TCNT0
Bit
7
6
5
4
3
2
1
0
$32 ($52)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
7
6
5
4
3
2
TCNT0
Timer/Counter2 – TCNT2
Bit
1
0
$23 ($43)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCNT2
These 8-bit registers contain the value of the Timer/Counters.
Both Timer/Counters are realized as up or up/down (in PWM mode) counters with read
and write access. If the Timer/Counter is written to and a clock source is selected, it continues counting in the timer clock cycle following the write operation.
Timer/Counter0 Output
Compare Register – OCR0
Timer/Counter2 Output
Compare Register – OCR2
Bit
7
6
5
4
3
2
1
0
$31 ($51)
MSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
Bit
LSB
OCR0
0
$22 ($42)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
OCR2
The Output Compare Registers are 8-bit read/write registers. The Timer/Counter Output
Compare Registers contain the data to be continuously compared with the
Timer/Counter. Actions on compare matches are specified in TCCR0 and TCCR2. A
software write to the Timer/Counter Register blocks compare matches in the next
Timer/Counter clock cycle. This prevents immediate interrupts when initializing the
Timer/Counter.
A compare match will set the Compare Interrupt Flag in the CPU clock cycle following
the compare event.
Timer/Counters 0 and 2 in
PWM Mode
When PWM mode is selected, the Timer/Counter either wraps (overflows) when it
reaches $FF or it acts as an up/down counter.
If the up/down mode is selected, the Timer/Counter and the Output Compare Registers
(OCR0 or OCR2) form an 8-bit, free-running, glitch-free and phase-correct PWM with
outputs on the PB0(OC0/PWM0) or PB1(OC2/PWM2) pin.
If the Overflow mode is selected, the Timer/Counter and the Output Compare Registers
(OCR0 or OCR2) form an 8-bit, free-running and glitch-free PWM, operating with twice
the speed of the up/down counting mode.
44
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
PWM Modes (Up/Down and
Overflow)
The two different PWM modes are selected by the CTC0 or CTC2 bit in the
Timer/Counter Control Registers – TCCR0 or TCCR2, respectively.
If CTC0/CTC2 is cleared and PWM mode is selected, the Timer/Counter acts as an
up/down counter, counting up from $00 to $FF, where it turns and counts down again to
zero before the cycle is repeated. When the counter value matches the contents of the
Output Compare Register, the PB0(OC0/PWM0) or PB1(OC2/PWM2) pin is set or
cleared according to the settings of the COMn1/COMn0 bits in the Timer/Counter Control Registers TCCR0 or TCCR2.
If CTC0/CTC2 is set and PWM mode is selected, the Timer/Counters will wrap and start
counting from $00 after reaching $FF. The PB0(OC0/PWM0) or PB1(OC2/PWM2) pin
will be set or cleared according to the settings of COMn1/COMn0 on a Timer/Counter
overflow or when the counter value matches the contents of the Output Compare Register. Refer to Table 12 for details.
Table 12. Compare Mode Select in PWM Mode(1)
CTCn
COMn1
COMn0
0
0
0
Not connected
0
0
1
Not connected
0
1
0
Cleared on compare match, up-counting. Set on
compare match, down-counting (non-inverted
PWM).
fTCK0/2/510
0
1
1
Cleared on compare match, down-counting. Set
on compare match, up-counting (inverted PWM).
fTCK0/2/510
1
0
0
Not connected
1
0
1
Not connected
1
1
0
Cleared on compare match, set on overflow
fTCK0/2/256
1
1
1
Set on compare match, cleared on overflow
fTCK0/2/256
Note:
Effect on Compare Pin
Frequency
1. n = 0 or 2
Note that in PWM mode, the value to be written to the Output Compare Register is first
transferred to a temporary location and then latched into the OCR when the
Timer/Counter reaches $FF. This prevents the occurrence of odd-length PWM pulses
(glitches) in the event of an unsynchronized OCR0 or OCR2 write. See Figure 33 and
Figure 34 for examples.
45
1228D–AVR–02/07
Figure 33. Effects of Unsynchronized OCR Latching in Up/Down Mode
Compare Value changes
Counter Value
Compare Value
PWM Output OCn
Synchronized OCn Latch
Compare Value changes
Counter Value
Compare Value
PWM Output OCn
Unsynchronized OCn Latch
Glitch
Figure 34. Effects of Unsynchronized OCR Latching in Overflow Mode.
Compare Value changes
Counter Value
Compare Value
PWM Output OCn
Synchronized OCn Latch
Compare Value changes
Counter Value
Compare Value
PWM Output OCn
Unsynchronized OCn Latch
Note:
Glitch
n = 0 or 2 (Figure 33 and Figure 34)
During the time between the write and the latch operation, a read from the Output Compare Registers will read the contents of the temporary location. This means that the
most recently written value always will read out of OCR0 and OCR2.
When the Output Compare Register contains $00 or $FF, and the up/down PWM mode
is selected, the output PB0(OC0/PWM0)/PB1(OC2/PWM2) is updated to low or high on
the next compare match according to the settings of COMn1/COMn0. This is shown in
Table 13. In overflow PWM mode, the output PB0(OC0/PWM0)/PB1(OC2/PWM2) is
held low or high only when the Output Compare Register contains $FF.
Table 13. PWM Outputs OCRn = $00 or $FF(1)(2)
Note:
COMn1
COMn0
OCRn
Output PWMn
1
0
$00
L
1
0
$FF
H
1
1
$00
H
1
1
$FF
L
1. n = 0 or 2
2. In overflow PWM mode, the table above is only valid for OCRn = $FF.
46
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
In up/down PWM mode, the Timer Overflow Flag (TOV0 or TOV2) is set when the
counter advances from $00. In overflow PWM mode, the Timer Overflow Flag is set as
in normal Timer/Counter mode. Timer Overflow Interrupt0 and 2 operate exactly as in
normal Timer/Counter mode, i.e., they are executed when TOV0 or TOV2 are set, provided that Timer Overflow Interrupt and global interrupts are enabled. This also applies
to the Timer Output Compare flag and interrupt.
Asynchronous Status
Register – ASSR
Bit
7
6
5
4
3
2
1
0
$26 ($46)
–
–
–
–
AS2
TCN2UB
OCR2UB
TCR2UB
Read/Write
R
R
R
R
R/W
R
R
R
Initial Value
0
0
0
0
0
0
0
0
ASSR
• Bits 7..4 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
• Bit 3 – AS2: Asynchronous Timer/Counter2 Mode
When this bit is cleared (zero), Timer/Counter2 is clocked from the internal system
clock, CK. If AS2 is set, the Timer/Counter2 is clocked from the TOSC1 pin. Pins PD4
and PD5 become connected to a crystal Oscillator and cannot be used as general I/O
pins. When the value of this bit is changed, the contents of TCNT2, OCR2 and TCCR2
might get corrupted.
• Bit 2 – TCN2UB: Timer/Counter2 Update Busy
When Timer/Counter2 operates asynchronously and TCNT2 is written, this bit becomes
set (one). When TCNT2 has been updated from the temporary storage register, this bit
is cleared (zero) by hardware. A logical “0” in this bit indicates that TCNT2 is ready to be
updated with a new value.
• Bit 1 – OCR2UB: Output Compare Register2 Update Busy
When Timer/Counter2 operates asynchronously and OCR2 is written, this bit becomes
set (one). When OCR2 has been updated from the temporary storage register, this bit is
cleared (zero) by hardware. A logical “0” in this bit indicates that OCR2 is ready to be
updated with a new value.
• Bit 0 – TCR2UB: Timer/Counter Control Register2 Update Busy
When Timer/Counter2 operates asynchronously and TCCR2 is written, this bit becomes
set (one). When TCCR2 has been updated from the temporary storage register, this bit
is cleared (zero) by hardware. A logical “0” in this bit indicates that TCCR2 is ready to be
updated with a new value.
If a write is performed to any of the three Timer/Counter2 Registers while its update
Busy Flag is set (one), the updated value might get corrupted and cause an unintentional interrupt to occur.
The mechanisms for reading TCNT2, OCR2 and TCCR2 are different. When reading
TCNT2, the actual timer value is read. When reading OCR2 or TCCR2, the value in the
temporary storage register is read.
47
1228D–AVR–02/07
Asynchronous Operation of
Timer/Counter2
When Timer/Counter2 operates asynchronously, some considerations must be taken:
•
Warning: When switching between asynchronous and synchronous clocking of
Timer/Counter2, the Timer Registers TCNT2, OCR2, and TCCR2 might get
corrupted. A safe procedure for switching clock source is:
1. Disable the Timer/Counter2 interrupts by clearing OCIE2 and TOIE2.
2. Select clock source by setting AS2 as appropriate.
3. Write new values to TCNT2, OCR2, and TCCR2.
4. To switch to asynchronous operation: Wait for TCN2UB, OCR2UB, and
TCR2UB.
5. Enable interrupts, if needed.
•
The Oscillator is optimized for use with a 32,768 Hz watch crystal. An external clock
signal applied to this pin goes through the same amplifier having a bandwidth of
256 kHz. The external clock signal should therefore be in the interval 0 Hz 256 kHz. The frequency of the clock signal applied to the TOSC1 pin must be lower
than one fourth of the CPU main clock frequency.
•
When writing to one of the registers TCNT2, OCR2, or TCCR2, the value is
transferred to a temporary register, and latched after two positive edges on TOSC1.
The user should not write a new value before the contents of the temporary register
have been transferred to its destination. Each of the three mentioned registers have
their individual temporary register, which means that e.g., writing to TCNT2 does not
disturb an OCR2 write in progress. To detect that a transfer to the destination
register has taken place, a Asynchronous Status Register – ASSR has been
implemented.
•
When entering Power-save mode after having written to TCNT2, OCR2 or TCCR2,
the user must wait until the written register has been updated if Timer/Counter2 is
used to wake up the device. Otherwise, the MCU will go to sleep before the changes
have had any effect. This is extremely important if the Output Compare2 interrupt is
used to wake up the device; output compare is disabled during write to OCR2 or
TCNT2. If the write cycle is not finished (i.e., the MCU enters sleep mode before the
OCR2UB bit returns to zero), the device will never get a compare match and the
MCU will not wake up.
•
If Timer/Counter2 is used to wake up the device from Power-save mode,
precautions must be taken if the user wants to re-enter Power-save mode: The
interrupt logic needs one TOSC1 cycle to be reset. If the time between wake-up and
re-entering Power-save mode is less than one TOSC1 cycle, the interrupt will not
occur and the device will fail to wake up. If the user is in doubt whether the time
before re-entering Power-save is sufficient, the following algorithm can be used to
ensure that one TOSC1 cycle has elapsed:
1. Write a value to TCCR2, TCNT2, or OCR2.
2. Wait until the corresponding Update Busy Flag in ASSR returns to zero.
3. Enter Power-save mode.
•
48
When asynchronous operation is selected, the 32 kHz Oscillator for Timer/Counter2
is always running, except in Power-down mode. After a Power-up Reset or wake-up
from power-down, the user should be aware of the fact that this Oscillator might take
as long as one second to stabilize. The user is advised to wait for at least one
second before using Timer/Counter2 after power-up or wake-up from power-down.
The contents of all Timer/Counter2 Registers must be considered lost after a wakeup from power-down, due to unstable clock signal upon start-up, regardless of
whether the Oscillator is in use or a clock signal is applied to the TOSC pin.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Timer/Counter1
•
Description of wake-up from Power-save mode when the timer is clocked
asynchronously: When the interrupt condition is met, the wake-up process is started
on the following cycle of the timer clock, that is, the timer is always advanced by at
least 1 before the processor can read the counter value. The Interrupt Flags are
updated three processor cycles after the processor clock has started. During these
cycles, the processor executes instructions, but the interrupt condition is not
readable and the interrupt routine has not started yet.
•
During asynchronous operation, the synchronization of the Interrupt Flags for the
asynchronous timer takes three processor cycles plus one timer cycle. The timer is
therefore advanced by at least 1 before the processor can read the timer value,
causing the setting of the Interrupt Flag. The output compare pin is changed on the
timer clock and is not synchronized to the processor clock.
Figure 35 shows the block diagram for Timer/Counter1.
Figure 35. Timer/Counter1 Block Diagram
8
7
PSR2
PSR10
SPECIAL FUNCTIONS
IO REGISTER (SFIOR)
CS10
CS11
CS12
CTC1
ICES1
ICNC1
FOC1B
T/C1 CONTROL
REGISTER B (TCCR1B)
PWM10
FOC1A
PWM11
COM1B1
COM1B0
COM1A0
COM1A1
T/C1 CONTROL
REGISTER A (TCCR1A)
OCF0
TOV0
ICF1
OCF2
TOV2
OCF1B
OCF1A
T/C1 INPUT
CAPTURE IRQ
OCF0
OCF2
TOV0
OCF1B
ICF1
T/C1 COMPARE
MATCHB IRQ
TIMER INT. FLAG
REGISTER (TIFR)
TOV1
15
TOV2
TOV1
TIMER INT. MASK
REGISTER (TIMSK)
OCF1A
T/C1 COMPARE
MATCHA IRQ
OCIE0
OCIE2
TOIE0
TICIE1
OCIE1B
TOIE2
OCIE1A
TOIE1
8-BIT DATA BUS
T/C1 OVERFLOW IRQ
0
T/C1 INPUT CAPTURE REGISTER (ICR1)
CK
CONTROL
LOGIC
T1
CAPTURE
TRIGGER
15
8
7
0
15
8
7
T/C CLEAR
T/C CLOCK SOURCE
TIMER/COUNTER1 (TCNT1)
UP/DOWN
0
15
16 BIT COMPARATOR
15
8
7
8
7
0
16 BIT COMPARATOR
0
TIMER/COUNTER1 OUTPUT COMPARE REGISTER A
15
8
7
0
TIMER/COUNTER1 OUTPUT COMPARE REGISTER B
The 16-bit Timer/Counter1 can select clock source from CK, prescaled CK or an external pin. In addition, it can be stopped as described in “Timer/Counter1 Control Register
B – TCCR1B”. The different Status Flags (Overflow, Compare Match, and Capture
Event) are found in the Timer/Counter Interrupt Flag Register (TIFR). Control signals
are found in the Timer/Counter1 Control Registers (TCCR1A and TCCR1B). The interrupt enable/disable settings for Timer/Counter1 are found in the Timer/Counter Interrupt
Mask Register (TIMSK).
When Timer/Counter1 is externally clocked, the external signal is synchronized with the
Oscillator frequency of the CPU. To assure proper sampling of the external clock, the
minimum time between two external clock transitions must be at least one internal CPU
49
1228D–AVR–02/07
clock period. The external clock signal is sampled on the rising edge of the internal CPU
clock.
The 16-bit Timer/Counter1 features both a high-resolution and a high-accuracy usage
with the lower prescaling opportunities. Similarly, the high-prescaling opportunities
make the Timer/Counter1 useful for lower speed functions or exact timing functions with
infrequent actions.
The Timer/Counter1 supports two Output Compare functions using the Output Compare
Register 1 A and B (OCR1A and OCR1B) as the data sources to be compared to the
Timer/Counter1 contents. The Output Compare functions include optional clearing of
the counter on compareA match and actions on the Output Compare pins on both compare matches.
Timer/Counter1 can also be used as an 8-, 9-, or 10-bit Pulse Width Modulator. In this
mode the counter and the OCR1A/OCR1B Registers serve as a dual glitch-free standalone PWM with centered pulses. Alternatively, the Timer/Counter1 can be configured
to operate at twice the speed in PWM mode, but without centered pulses. Refer to page
55 for a detailed description of this function.
The Input Capture function of Timer/Counter1 provides a capture of the Timer/Counter1
contents to the Input Capture Register (ICR1), triggered by an external event on the
Input Capture Pin (ICP). The actual capture event settings are defined by the
Timer/Counter1 Control Register (TCCR1B). In addition, the Analog Comparator can be
set to trigger the Input Capture. Refer to the section, “The Analog Comparator”, for
details on this. The ICP pin logic is shown in Figure 36.
Figure 36. ICP Pin Schematic Diagram
If the noise canceler function is enabled, the actual trigger condition for the Capture
Event is monitored over four samples, and all four must be equal to activate the Capture
Flag.
Timer/Counter1 Control
Register A – TCCR1A
Bit
7
6
5
4
3
2
1
0
COM1A1
COM1A0
COM1B1
COM1B0
FOC1A
FOC1B
PWM11
PWM10
Read/Write
R/W
R/W
R/W
R/W
R/w
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$2F ($4F)
TCCR1A
• Bits 7, 6 – COM1A1, COM1A0: Compare Output Mode1A, Bits 1 and 0
The COM1A1 and COM1A0 control bits determine any output pin action following a
compare match in Timer/Counter1. Any output pin actions affect pin OC1A (Output
CompareA pin 1). This is an alternative function to an I/O port, and the corresponding
direction control bit must be set (one) to control an output pin. The control configuration
is shown in Table 14.
50
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Bits 5, 4 – COM1B1, COM1B0: Compare Output Mode1B, Bits 1 and 0
The COM1B1 and COM1B0 control bits determine any output pin action following a
compare match in Timer/Counter1. Any output pin actions affect pin OC1B (Output
CompareB). This is an alternative function to an I/O port, and the corresponding direction control bit must be set (one) to control an output pin. The following control
configuration is given:
Table 14. Compare 1 Mode Select(1)
COM1X1
COM1X0
0
0
Timer/Counter1 disconnected from output pin OC1X
0
1
Toggle the OC1X output line.
1
0
Clear the OC1X output line (to zero).
1
1
Set the OC1X output line (to one).
Note:
Description
1. X = A or B
In PWM mode, these bits have a different function. Refer to Table 18 for a detailed
description.
• Bit 3 – FOC1A: Force Output Compare1A
Writing a logical “1” to this bit forces a change in the compare match output pin PD5
according to the values already set in COM1A1 and COM1A0. If the COM1A1 and
COM1A0 bits are written in the same cycle as FOC1A, the new settings will not take
effect until the next compare match or forced compare match occurs. The Force Output
Compare bit can be used to change the output pin without waiting for a compare match
in the timer. The automatic action programmed in COM1A1 and COM1A0 happens as if
a Compare Match had occurred, but no interrupt is generated and it will not clear the
timer even if CTC1 in TCCR1B is set. The FOC1A bit will always be read as zero. The
setting of the FOC1A bit has no effect in PWM mode.
• Bit 2 – FOC1B: Force Output Compare1B
Writing a logical “1” to this bit forces a change in the compare match output pin PE2
according to the values already set in COM1B1 and COM1B0. If the COM1B1 and
COM1B0 bits are written in the same cycle as FOC1B, the new settings will not take
effect until the next compare match or forced compare match occurs. The Force Output
Compare bit can be used to change the output pin without waiting for a compare match
in the timer. The automatic action programmed in COM1B1 and COM1B0 happens as if
a Compare Match had occurred, but no interrupt is generated. The FOC1B bit will
always be read as zero. The setting of the FOC1B bit has no effect in PWM mode.
51
1228D–AVR–02/07
• Bits 1..0 – PWM11, PWM10: Pulse Width Modulator Select Bits
These bits select PWM operation of Timer/Counter1 as specified in Table 15. This mode
is described on page 55.
Table 15. PWM Mode Select
Timer/Counter1 Control
Register B – TCCR1B
PWM11
PWM10
0
0
PWM operation of Timer/Counter1 is disabled.
0
1
Timer/Counter1 is an 8-bit PWM.
1
0
Timer/Counter1 is a 9-bit PWM.
1
1
Timer/Counter1 is a 10-bit PWM.
Bit
Description
7
6
5
4
3
2
1
0
$2E ($4E)
ICNC1
ICES1
–
–
CTC1
CS12
CS11
CS10
Read/Write
R/W
R/W
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR1B
• Bit 7 – ICNC1: Input Capture1 Noise Canceler (4 CKs)
When the ICNC1 bit is cleared (zero), the Input Capture trigger noise canceler function
is disabled. The Input Capture is triggered at the first rising/falling edge sampled on the
ICP (Input Capture pin) as specified. When the ICNC1 bit is set (one), four successive
samples are measured on the ICP (Input Capture pin), and all samples must be high/low
according to the Input Capture trigger specification in the ICES1 bit. The actual sampling
frequency is XTAL clock frequency.
• Bit 6 – ICES1: Input Capture1 Edge Select
While the ICES1 bit is cleared (zero), the Timer/Counter1 contents are transferred to the
Input Capture Register (ICR1) on the falling edge of the Input Capture pin (ICP). While
the ICES1 bit is set (one), the Timer/Counter1 contents are transferred to the Input Capture Register (ICR1) on the rising edge of the Input Capture pin (ICP).
• Bits 5, 4 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
• Bit 3 – CTC1: Clear Timer/Counter1 on Compare Match
When the CTC1 control bit is set (one), the Timer/Counter1 is reset to $0000 in the clock
cycle after a compareA match. If the CTC1 control bit is cleared, Timer/Counter1 continues counting and is unaffected by a compare match. When a prescaling of 1 is used and
the Compare A Register is set to C, the timer will count as follows if CTC1 is set:
... | C-1 | C | 0 | 1 | ...
When the prescaler is set to divide by 8, the timer will count like this:
... | C-1, C-1, C-1, C-1, C-1, C-1, C-1, C-1 | C, C, C, C, C, C, C, C | 0, 0, 0, 0, 0, 0, 0, 0 | ...
In PWM mode, this bit has a different function. If the CTC1 bit is cleared in PWM mode,
the Timer/Counter1 acts as an up/down counter. If the CTC1 bit is set (one), the
Timer/Counter wraps when it reaches the TOP value. Refer to page 55 for a detailed
description.
52
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Bits 2, 1, 0 – CS12, CS11, CS10: Clock Select1, Bits 2, 1 and 0
The Clock Select1 bits 2, 1 and 0 define the prescaling source of Timer/Counter1.
Table 16. Clock 1 Prescale Select
CS12
CS11
CS10
Description
0
0
0
Stop, the Timer/Counter1 is stopped.
0
0
1
CK
0
1
0
CK/8
0
1
1
CK/64
1
0
0
CK/256
1
0
1
CK/1024
1
1
0
External Pin T1, falling edge
1
1
1
External Pin T1, rising edge
The Stop condition provides a Timer Enable/Disable function. The CK down divided
modes are scaled directly from the CK Oscillator clock. If the external pin modes are
used for Timer/Counter1, transitions on PB1/(T1) will clock the counter even if the pin is
configured as an output. This feature can give the user software control of the counting.
Timer/Counter1 Register –
TCNT1H AND TCNT1L
Bit
15
$2D ($4D)
14
13
12
11
10
9
TCNT1H
$2C ($4C)
Read/Write
Initial Value
8
MSB
LSB
7
6
5
4
3
2
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TCNT1L
This 16-bit register contains the prescaled value of the 16-bit Timer/Counter1. To
ensure that both the high and low bytes are read and written simultaneously when the
CPU accesses these registers, the access is performed using an 8-bit temporary register (TEMP). This temporary register is also used when accessing OCR1A, OCR1B, and
ICR1. If the main program and interrupt routines perform access to registers using
TEMP, interrupts must be disabled during access from the main program and interrupt
routines.
•
TCNT1 Timer/Counter1 Write
When the CPU writes to the High byte TCNT1H, the written data is placed in the TEMP
Register. Next, when the CPU writes the Low byte TCNT1L, this byte of data is combined with the byte data in the TEMP Register and all 16 bits are written to the TCNT1
Timer/Counter1 Register simultaneously. Consequently, the High byte TCNT1H must
be accessed first for a full 16-bit register write operation.
•
TCNT1 Timer/Counter1 Read
When the CPU reads the Low byte TCNT1L, the data of the Low byte TCNT1L is sent to
the CPU and the data of the High byte TCNT1H is placed in the TEMP Register. When
the CPU reads the data in the High byte TCNT1H, the CPU receives the data in the
TEMP Register. Consequently, the Low byte TCNT1L must be accessed first for a full
16-bit register read operation.
53
1228D–AVR–02/07
The Timer/Counter1 is realized as an up or up/down (in PWM mode) counter with read
and write access. If Timer/Counter1 is written to and a clock source is selected, the
Timer/Counter1 continues counting in the timer clock cycle after it is preset with the written value.
Timer/Counter1 Output
Compare Register – OCR1AH
AND OCR1AL
Bit
$2B ($4B)
15
14
13
12
11
10
9
8
MSB
OCR1AH
$2A ($4A)
Read/Write
Initial Value
Timer/Counter1 Output
Compare Register – OCR1BH
AND OCR1BL
Bit
$29 ($49)
LSB
7
6
5
4
3
2
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
15
14
13
12
11
10
9
8
MSB
OCR1BH
$28 ($48)
Read/Write
Initial Value
OCR1AL
LSB
7
6
5
4
3
2
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
OCR1BL
The Output Compare Registers are 16-bit read/write registers.
The Timer/Counter1 Output Compare Registers contain the data to be continuously
compared with Timer/Counter1. Actions on compare matches are specified in the
Timer/Counter1 Control and Status Registers. A software write to the Timer/Counter
Register blocks compare matches in the next Timer/Counter clock cycle. This prevents
immediate interrupts when initializing the Timer/Counter.
A compare match will set the Compare Interrupt Flag in the CPU clock cycle following
the compare event.
Since the Output Compare Registers (OCR1A and OCR1B) are 16-bit registers, a temporary register (TEMP) is used when OCR1A/B are written to ensure that both bytes are
updated simultaneously. When the CPU writes the High byte, OCR1AH or OCR1BH,
the data is temporarily stored in the TEMP Register. When the CPU writes the Low byte,
OCR1AL or OCR1BL, the TEMP Register is simultaneously written to OCR1AH or
OCR1BH. Consequently, the High byte OCR1AH or OCR1BH must be written first for a
full 16-bit register write operation.
The TEMP Register is also used when accessing TCNT1 and ICR1. If the main program
and interrupt routines perform access to registers using TEMP, interrupts must be disabled during access from the main program and interrupt routines.
Timer/Counter1 Input Capture
Register – ICR1H AND ICR1L
Bit
$25 ($45)
15
14
13
12
11
10
9
ICR1H
$24 ($44)
Read/Write
Initial Value
54
8
MSB
LSB
7
6
5
4
3
2
1
0
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ICR1L
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
The Input Capture Register is a 16-bit read-only register.
When the rising or falling edge (according to the Input Capture edge setting, ICES1) of
the signal at the Input Capture pin (ICP) is detected, the current value of the
Timer/Counter1 Register (TCNT1) is transferred to the Input Capture Register (ICR1). In
the same cycle, the Input Capture Flag (ICF1) is set (one).
Since the Input Capture Register (ICR1) is a 16-bit register, a temporary register
(TEMP) is used when ICR1 is read to ensure that both bytes are read simultaneously.
When the CPU reads the Low byte ICR1L, the data is sent to the CPU and the data of
the High byte ICR1H is placed in the TEMP Register. When the CPU reads the data in
the High byte ICR1H, the CPU receives the data in the TEMP Register. Consequently,
the Low byte ICR1L must be accessed first for a full 16-bit register read operation.
The TEMP Register is also used when accessing TCNT1, OCR1A and OCR1B. If the
main program and interrupt routines perform access to registers using TEMP, interrupts
must be disabled during access from the main program and interrupt routine.
Timer/Counter1 in PWM Mode
When the PWM mode is selected, Timer/Counter1 and the Output Compare Register1A
(OCR1A) and the Output Compare Register1B (OCR1B) form a dual 8-, 9-, or 10-bit,
free-running, glitch-free, and phase-correct PWM with outputs on the PD5(OC1A) and
PE2(OC1B) pins. In this mode the Timer/Counter1 acts as an up/down counter, counting up from $0000 to TOP (see Table 17), where it turns and counts down again to zero
before the cycle is repeated. When the counter value matches the contents of the 8, 9,
or 10 least significant bits (depends of the resolution) of OCR1A or OCR1B, the
PD5(OC1A)/PE2(OC1B) pins are set or cleared according to the settings of the
COM1A1/COM1A0 or COM1B1/COM1B0 bits in the Timer/Counter1 Control Register
(TCCR1A). Refer to Table 18 for details.
Alternatively, the Timer/Counter1 can be configured to a PWM that operates at twice the
speed as in the mode described above. Then the Timer/Counter1 and the Output Compare Register1A (OCR1A) and the Output Compare Register1B (OCR1B) form a dual
8-, 9- or 10-bit, free-running and glitch-free PWM with outputs on the PD5(OC1A) and
PE2(OC1B) pins.
Table 17. Timer TOP Values and PWM Frequency
CTC1
PWM11
PWM10
PWM Resolution
Timer TOP Value
Frequency
0
0
1
8-bit
$00FF (255)
fTCK1/510
0
1
0
9-bit
$01FF (511)
fTCK1/1022
0
1
1
10-bit
$03FF (1023)
fTCK1/2046
1
0
1
8-bit
$00FF (255)
fTCK1/256
1
1
0
9-bit
$01FF (511)
fTCK1/512
1
1
1
10-bit
$03FF (1023)
fTCK1/1024
As shown in Table 17, the PWM operates at either 8-, 9-, or 10-bit resolution. Note the
unused bits in OCR1A, OCR1B and TCNT1 will automatically be written to zero by hardware, i.e., bits 9 to 15 will be set to zero in OCR1A, OCR1B and TCNT1 if the 9-bit PWM
resolution is selected. This makes it possible for the user to perform read-modify-write
operations in any of the three resolution modes and the unused bits will be treated as
don’t care.
55
1228D–AVR–02/07
Table 18. Compare1 Mode Select in PWM Mode(1)
CTC1
COM1X1
COM1X0
0
0
0
Not connected
0
0
1
Not connected
0
1
0
Cleared on compare match, up-counting. Set on compare
match, down-counting (non-inverted PWM).
0
1
1
Cleared on compare match, down-counting. Set on compare
match, up-counting (inverted PWM).
1
0
0
Not connected
1
0
1
Not connected
1
1
0
Cleared on compare match, set on overflow.
1
1
1
Set on compare match, cleared on overflow.
Note:
Effect on OCX1
1. X = A or B
Note that in the PWM mode, the 8, 9 or 10 least significant OCR1A/OCR1B bits
(depends of resolution), when written, are transferred to a temporary location. They are
latched when Timer/Counter1 reaches the value TOP. This prevents the occurrence of
odd-length PWM pulses (glitches) in the event of an unsynchronized OCR1A/OCR1B
write. See Figure 37 and Figure 38 for an example in each mode.
Figure 37. Effects on Unsynchronized OCR1 Latching(1)
Compare Value changes
Counter Value
Compare Value
PWM Output OC1X
Synchronized
OCR1X Latch
Compare Value changes
Counter Value
Compare Value
PWM Output OC1X
Unsynchronized
Note:
56
OCR1X Latch
Glitch
1. Note: X = A or B
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 38. Effects of Unsynchronized OCR1 Latching in Overflow Mode1
PWM Output OC1x
Synchronized OC1x Latch
PWM Output OC1x
Unsynchronized OC1x Latch
Note:
1. Note: X = A or B
During the time between the write and the latch operation, a read from OCR1A or
OCR1B will read the contents of the temporary location. This means that the most
recently written value always will read out of OCR1A/B.
When the OCR1X contains $0000 or TOP, and the up/down PWM mode is selected, the
output OC1A/OC1B is updated to low or high on the next compare match according to
the settings of COM1A1/COM1A0 or COM1B1/COM1B0. This is shown in Table 19. In
overflow PWM mode, the output OC1A/OC1B is held low or high only when the Output
Compare Register contains TOP.
Table 19. PWM Outputs OCR1X = $0000 or TOP(1)
Note:
COM1X1
COM1X0
OCR1X
Output OC1X
1
0
$0000
L
1
0
TOP
H
1
1
$0000
H
1
1
TOP
L
1. X = A or B
In overflow PWM mode, the table above is only valid for OCR1X = TOP.
In up/down PWM mode, the Timer Overflow Flag1 (TOV1) is set when the counter
advances from $0000. In overflow PWM mode, the Timer Overflow Flag is set as in normal Timer/Counter mode. Timer Overflow Interrupt1 operates exactly as in normal
Timer/Counter mode, i.e., it is executed when TOV1 is set, provided that Timer Overflow
Interrupt1 and global interrupts are enabled. This also applies to the Timer Output
Compare1 Flags and interrupts.
57
1228D–AVR–02/07
Watchdog Timer
The Watchdog Timer is clocked from a separate On-chip Oscillator that runs at 1 MHz.
This is the typical value at VCC = 5V. See characterization data for typical values at other
VCC levels. By controlling the Watchdog Timer prescaler, the Watchdog Reset interval
can be adjusted (see Table 20 for a detailed description). The WDR (Watchdog Reset)
instruction resets the Watchdog Timer. Eight different clock cycle periods can be
selected to determine the reset period. If the reset period expires without another
Watchdog Reset, the ATmega161 resets and executes from the Reset Vector. For timing details on the Watchdog Reset, refer to page 28.
To prevent unintentional disabling of the Watchdog, a special turn-off sequence must be
followed when the Watchdog is disabled. Refer to the description of the Watchdog Timer
Control Register for details.
Figure 39. Watchdog Timer
Watchdog Timer Control
Register – WDTCR
Bit
7
6
5
4
3
2
1
0
$21 ($41)
–
–
–
WDTOE
WDE
WDP2
WDP1
WDP0
Read/Write
R
R
R
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
WDTCR
• Bits 7..5 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and will always read as zero.
• Bit 4 – WDTOE: Watchdog Turn-off Enable
This bit must be set (one) when the WDE bit is cleared. Otherwise, the Watchdog will
not be disabled. Once set, hardware will clear this bit to zero after four clock cycles.
Refer to the description of the WDE bit for a Watchdog disable procedure.
• Bit 3 – WDE: Watchdog Enable
When the WDE is set (one), the Watchdog Timer is enabled and if the WDE is cleared
(zero), the Watchdog Timer function is disabled. WDE can only be cleared if the
58
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
WDTOE bit is set (one). To disable an enabled Watchdog Timer, the following procedure must be followed:
1. In the same operation, write a logical “1” to WDTOE and WDE. A logical “1” must
be written to WDE even though it is set to one before the disable operation starts.
2. Within the next four clock cycles, write a logical “0” to WDE. This disables the
Watchdog.
• Bits 2..0 – WDP2, WDP1, WDP0: Watchdog Timer Prescaler 2, 1 and 0
The WDP2, WDP1 and WDP0 bits determine the Watchdog Timer prescaling when the
Watchdog Timer is enabled. The different prescaling values and their corresponding
time-out periods are shown in Table 20.
Table 20. Watchdog Timer Prescale Select (1)
WDP2
WDP1
WDP0
Number of WDT
Oscillator Cycles
Typical Time-out
at VCC = 3.0V
Typical Time-out
at VCC = 5.0V
0
0
0
16K
47 ms
15 ms
0
0
1
32K
94 ms
30 ms
0
1
0
64K
0.19 s
60 ms
0
1
1
128K
0.38 s
0.12 s
1
0
0
256K
0.75 s
0.24 s
1
0
1
512K
1.5 s
0.49 s
1
1
0
1,024K
3.0 s
0.97 s
1
1
1
2,048K
6.0 s
1.9 s
Note:
1. The frequency of the Watchdog Oscillator is voltage-dependent, as shown in the
Electrical Characteristics section.
The WDR (Watchdog Reset) instruction should always be executed before the
Watchdog Timer is enabled. This ensures that the reset period will be in accordance
with the Watchdog Timer prescale settings. If the Watchdog Timer is enabled without
reset, the Watchdog Timer may not start counting from zero.
To avoid unintentional MCU Reset, the Watchdog Timer should be disabled or reset
before changing the Watchdog Timer Prescale Select.
59
1228D–AVR–02/07
EEPROM Read/Write
Access
The EEPROM Access Registers are accessible in the I/O space.
The write access time is in the range of 1.9 - 3.4 ms, depending on the frequency of the
RC Oscillator used to time the EEPROM access time. See Table 22 for details. A selftiming function, however, lets the user software detect when the next byte can be written. If the user code contains code that writes the EEPROM, some precaution must be
taken. In heavily filtered power supplies, VCC is likely to rise or fall slowly on powerup/down. This causes the device for some period of time to run at a voltage lower than
specified as minimum for the clock frequency used. CPU operation under these conditions is likely cause the Program Counter to perform unintentional jumps and eventually
execute the EEPROM write code. To secure EEPROM integrity, the user is advised to
use an external Under-voltage Reset circuit in this case.
In order to prevent unintentional EEPROM writes, a specific write procedure must be followed. Refer to the description of the EEPROM Control Register for details on this.
When the EEPROM is written, the CPU is halted for two clock cycles before the next
instruction is executed. When the EEPROM is read, the CPU is halted for four clock
cycles before the next instruction is executed.
EEPROM Address Register –
EEARH and EEARL
Bit
15
14
13
12
11
10
9
8
$1F ($3F)
–
–
–
–
–
–
–
EEAR8
EEARH
$1E ($3E)
EEAR7
EEAR6
EEAR5
EEAR4
EEAR3
EEAR2
EEAR1
EEAR0
EEARL
7
6
5
4
3
2
1
0
Read/Write
Initial Value
R
R
R
R
R
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X
• Bits 15..9 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and will always read as zero.
• Bits 8..0 – EEAR8..0: EEPROM Address
The EEPROM Address Registers (EEARH and EEARL) specify the EEPROM address
in the 512-byte EEPROM space. The EEPROM data bytes are addressed linearly
between 0 and 511. The initial value of EEAR is undefined. A proper value must be written before the EEPROM may be accessed.
EEPROM Data Register –
EEDR
Bit
7
6
5
4
3
2
1
0
$1D ($3D)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
EEDR
• Bits 7..0 – EEDR7..0: EEPROM Data
For the EEPROM write operation, the EEDR Register contains the data to be written to
the EEPROM in the address given by the EEAR Register. For the EEPROM read operation, the EEDR contains the data read out from the EEPROM at the address given by
EEAR.
60
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
EEPROM Control Register –
EECR
Bit
7
6
5
4
3
2
1
0
$1C ($3C)
–
–
–
–
EERIE
EEMWE
EEWE
EERE
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
X
0
EECR
• Bits 7..4 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and will always read as zero.
• Bit 3 – EERIE: EEPROM Ready Interrupt Enable
When the I-bit in SREG and EERIE are set (one), the EEPROM Ready Interrupt is
enabled. When cleared (zero), the interrupt is disabled. The EEPROM Ready interrupt
generates a constant interrupt when EEWE is cleared (zero).
• Bit 2 – EEMWE: EEPROM Master Write Enable
The EEMWE bit determines whether setting EEWE to one causes the EEPROM to be
written. When EEMWE is set (one), setting EEWE will write data to the EEPROM at the
selected address. If EEMWE is zero, setting EEWE will have no effect. When EEMWE
has been set (one) by software, hardware clears the bit to zero after four clock cycles.
See the description of the EEWE bit for an EEPROM write procedure.
• Bit 1 – EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal (EEWE) is the write strobe to the EEPROM. When
address and data are correctly set up, the EEWE bit must be set to write the value into
the EEPROM. The EEMWE bit must be set when the logical “1” is written to EEWE, otherwise no EEPROM write takes place. The following procedure should be followed
when writing the EEPROM (the order of steps 2 and 3 is not essential):
1. Wait until EEWE becomes zero.
2. Write new EEPROM address to EEAR (optional).
3. Write new EEPROM data to EEDR (optional).
4. Write a logical “1” to the EEMWE bit in EECR (to be able to write a logical “1” to
the EEMWE bit, the EEWE bit must be written to zero in the same cycle).
5. Within four clock cycles after setting EEMWE, write a logical “1” to EEWE.
Caution: An interrupt between step 4 and step 5 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the
EEPROM is interrupting another EEPROM access, the EEAR or EEDR Register will be
modified, causing the interrupted EEPROM access to fail. It is recommended to have
the Global Interrupt Flag cleared during the four last steps to avoid these problems.
When the write access time has elapsed, the EEWE bit is cleared (zero) by hardware.
The user software can poll this bit and wait for a zero before writing the next byte. When
EEWE has been set, the CPU is halted for two cycles before the next instruction is
executed.
• Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable signal (EERE) is the read strobe to the EEPROM. When
the correct address is set up in the EEAR Register, the EERE bit must be set. When the
EERE bit is cleared (zero) by hardware, requested data is found in the EEDR Register.
The EEPROM read access takes one instruction and there is no need to poll the EERE
61
1228D–AVR–02/07
bit. When EERE has been set, the CPU is halted for four cycles before the next instruction is executed.
The user should poll the EEWE bit before starting the read operation. If a write operation
is in progress when new data or address is written to the EEPROM I/O Registers, the
write operation will be interrupted and the result is undefined.
An RC Oscillator is used to time EEPROM write access. The table below lists the typical
programming time listed for EEPROM access from CPU.
Table 21. EEPROM Access Time from CPU“See “Typical Characteristics” on page 138
to find RC Oscillator frequency.” on page 62(1)
Symbol
EEPROM write (from CPU)
Note:
Prevent EEPROM
Corruption
No. of RC
Oscillator Cycles
Min Programming
Time
Max Programming
Time
2048
2.0 ms
3.4 ms
1. See “Typical Characteristics” on page 138 to find RC Oscillator frequency.
During periods of low VCC, the EEPROM data can be corrupted because the supply voltage is too low for the CPU and the EEPROM to operate properly. These issues are the
same as for board-level systems using the EEPROM, and the same design solutions
should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too
low. First, a regular write sequence to the EEPROM requires a minimum voltage to
operate correctly. Secondly, the CPU itself can execute instructions incorrectly if the
supply voltage for executing instructions is too low.
EEPROM data corruption can easily be avoided by following these design recommendations (one is sufficient):
1. Keep the AVR RESET active (low) during periods of insufficient power supply
voltage. An external low VCC Reset Protection circuit can be applied.
2. Keep the AVR core in Power-down Sleep mode during periods of low VCC. This
will prevent the CPU from attempting to decode and execute instructions, effectively protecting the EEPROM Registers from unintentional writes.
3. Store constants in Flash memory if the ability to change memory contents from
software is not required. Flash memory cannot be updated by the CPU unless
the boot loader software supports writing to the Flash and the Boot Lock bits are
configured so that writing to the Flash memory from the CPU is allowed. See
“Boot Loader Support” on page 110 for details.
62
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Serial Peripheral
Interface – SPI
The Serial Peripheral Interface (SPI) allows high-speed synchronous data transfer
between the ATmega161 and peripheral devices or between several AVR devices. The
ATmega161 SPI features include the following:
• Full-duplex, 3-wire Synchronous Data Transfer
• Master or Slave Operation
• LSB First or MSB First Data Transfer
• Seven Programmable Bit Rates
• End-of-Transmission Interrupt Flag
• Write Collision Flag Protection
• Wake-up from Idle Mode (Slave Mode Only)
• Double-speed (CK/2) Master SPI Mode
Figure 40. SPI Block Diagram
SPI2X
SPI2X
DIVIDER
/2/4/8/16/32/64/128
63
1228D–AVR–02/07
The interconnection between Master and Slave CPUs with SPI is shown in Figure 41.
The PB7(SCK) pin is the Clock Output in the Master mode and is the clock input in the
Slave mode. Writing to the SPI Data Register of the Master CPU starts the SPI clock
generator, and the data written shifts out of the PB5(MOSI) pin and into the PB5(MOSI)
pin of the Slave CPU. After shifting one byte, the SPI clock generator stops, setting the
End-of-Transmission Flag (SPIF). If the SPI Interrupt Enable bit (SPIE) in the SPCR
Register is set, an interrupt is requested. The Slave Select input, PB4(SS), is set low to
select an individual Slave SPI device. The two Shift Registers in the Master and the
Slave can be considered as one distributed 16-bit circular Shift Register. This is shown
in Figure 41. When data is shifted from the Master to the Slave, data is also shifted in
the opposite direction, simultaneously. This means that during one shift cycle, data in
the Master and the Slave are interchanged.
Figure 41. SPI Master-Slave Interconnection
The system is single-buffered in the transmit direction and double-buffered in the
receive direction. This means that bytes to be transmitted cannot be written to the SPI
Data Register before the entire shift cycle is completed. When receiving data, however,
a received byte must be read from the SPI Data Register before the next byte has been
completely shifted in. Otherwise, the first byte is lost.
When the SPI is enabled, the data direction of the MOSI, MISO, SCK and SS pins is
overridden according to Table 22.
Table 22. SPI Pin Overrides(1)
Pin
Direction, Master SPI
Direction, Slave SPI
MOSI
User Defined
Input
MISO
Input
User Defined
SCK
User Defined
Input
SS
User Defined
Input
Note:
64
1. See “Alternate Functions of Port B” on page 92 for a detailed description of how to
define the direction of the user defined SPI pins.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
SS Pin Functionality
When the SPI is configured as a Master (MSTR in SPCR is set), the user can determine
the direction of the SS pin. If SS is configured as an output, the pin is a general output
pin, which does not affect the SPI system. If SS is configured as an input, it must be held
high to ensure Master SPI operation. If the SS pin is driven low by peripheral circuitry
when the SPI is configured as Master with the SS pin defined as an input, the SPI system interprets this as another Master selecting the SPI as a Slave and starting to send
data to it. To avoid bus contention, the SPI system takes the following actions:
1. The MSTR bit in SPCR is cleared and the SPI system becomes a Slave. As a
result of the SPI becoming a Slave, the MOSI and SCK pins become inputs.
2. The SPIF Flag in SPSR is set, and if the SPI interrupt is enabled and the I-bit in
SREG is set, the interrupt routine will be executed.
Thus, when interrupt-driven SPI transmission is used in Master mode, and there exists a
possibility that SS is driven low. The interrupt should always check that the MSTR bit is
still set. Once the MSTR bit has been cleared by a Slave select, it must be set by the
user to re-enable SPI Master mode.
When the SPI is configured as a Slave, the SS pin is always input. When SS is held low,
the SPI is activated and MISO becomes an output if configured so by the user. All other
pins are inputs. When SS is driven high, all pins are inputs and the SPI is passive, which
means that it will not receive incoming data. Note that the SPI logic will be reset once
the SS pin is brought high. If the SS pin is brought high during a transmission, the SPI
will stop sending and receiving immediately and both data received and data sent must
be considered lost.
Data Modes
There are four combinations of SCK phase and polarity with respect to serial data,
which are determined by control bits CPHA and CPOL. The SPI data transfer formats
are shown in Figure 42 and Figure 43.
Figure 42. SPI Transfer Format with CPHA = 0 and DORD = 0
65
1228D–AVR–02/07
Figure 43. SPI Transfer Format with CPHA = 1 and DORD = 0
SPI Control Register – SPCR
Bit
7
6
5
4
3
2
1
0
$0D ($2D)
SPIE
SPE
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SPCR
• Bit 7 – SPIE: SPI Interrupt Enable
This bit causes the SPI interrupt to be executed if SPIF bit in the SPSR Register is set
and if the global interrupt enable bit in SREG is set.
• Bit 6 – SPE: SPI Enable
When the SPE bit is set (one), the SPI is enabled. This bit must be set to enable any SPI
operations.
• Bit 5 – DORD: Data Order
When the DORD bit is set (one), the LSB of the data word is transmitted first.
When the DORD bit is cleared (zero), the MSB of the data word is transmitted first.
• Bit 4 – MSTR: Master/Slave Select
This bit selects Master SPI mode when set (one), and Slave SPI mode when cleared
(zero). If SS is configured as an input and is driven low while MSTR is set, MSTR will be
cleared and SPIF in SPSR will become set. The user will then have to set MSTR to reenable SPI Master mode.
• Bit 3 – CPOL: Clock Polarity
When this bit is set (one), SCK is high when idle. When CPOL is cleared (zero), SCK is
low when idle. Refer to Figure 42 and Figure 43 for additional information.
• Bit 2 – CPHA: Clock Phase
Refer to Figure 42 or Figure 43 for the functionality of this bit.
66
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Bits 1, 0 – SPR1, SPR0: SPI Clock Rate Select 1 and 0
These two bits control the SCK rate of the device configured as a Master. SPR1 and
SPR0 have no effect on the Slave. The relationship between SCK and the Oscillator
Clock frequency (fcl) is shown in Table 23:
Table 23. Relationship between SCK and the Oscillator Frequency(1)
Note:
SPI2X
SPR1
SPR0
SCK Frequency
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
fcl/4
fcl/16
fcl/64
fcl/128
fcl/2
fcl/8
fcl/32
fcl/64
1. When the SPI is configured as Slave, the SPI is only guaranteed to work at fcl/4.
SPI Status Register – SPSR
Bit
7
6
5
4
3
2
1
0
$0E ($2E)
SPIF
WCOL
–
–
–
–
–
SPI2X
Read/Write
R
R
R
R
R
R
R
R/W
Initial Value
0
0
0
0
0
0
0
0
SPSR
• Bit 7 – SPIF: SPI Interrupt Flag
When a serial transfer is complete, the SPIF bit is set (one) and an interrupt is generated if SPIE in SPCR is set (one) and global interrupts are enabled. If SS is an input and
is driven low when the SPI is in Master mode, this will also set the SPIF Flag. SPIF is
cleared by hardware when executing the corresponding Interrupt Handling Vector. Alternatively, the SPIF bit is cleared by first reading the SPI Status Register with SPIF set
(one), then by accessing the SPI Data Register (SPDR).
• Bit 6 – WCOL: Write Collision Flag
The WCOL bit is set if the SPI Data Register (SPDR) is written during a data transfer.
The WCOL bit (and the SPIF bit) are cleared (zero) by first reading the SPI Status Register with WCOL set (one), and then by accessing the SPI Data Register.
• Bits 5..1 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and will always read as zero.
• Bit 0 – SPI2X: Double SPI Speed Bit
When this bit is set (one), the SPI speed (SCK frequency) will be doubled when the SPI
is in Master mode (see Table 23). This means that the maximum SCK period will be two
CPU clock periods. When the SPI is configured as Slave, the SPI is only guaranteed to
work at fcl/4.
The SPI interface on the ATmega161 is also used for Program memory and EEPROM
downloading or uploading. See page 125 for serial programming and verification.
67
1228D–AVR–02/07
SPI Data Register – SPDR
Bit
7
6
5
4
3
2
1
0
$0F ($2F)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
x
x
x
x
x
x
x
x
SPDR
Undefined
The SPI Data Register is a read/write register used for data transfer between the Register File and the SPI Shift Register. Writing to the register initiates data transmission.
Reading the register causes the Shift Register Receive buffer to be read.
68
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
UARTs
The ATmega161 features two full-duplex (separate Receive and Transmit Registers)
Universal Asynchronous Receiver and Transmitters (UARTs). The main features are:
• Baud Rate Generator Generates any Baud Rate
• High Baud Rates at low XTAL Frequencies
• 8 or 9 Bits Data
• Noise Filtering
• Overrun Detection
• Framing Error Detection
• False Start Bit Detection
• Three Separate Interrupts on TX Complete, TX Data Register Empty, and RX Complete
• Multi-processor Communication Mode
• Double-speed UART Mode
Data Transmission
A block schematic of the UART Transmitter is shown in Figure 44. The two UARTs are
identical and the functionality is described in general for the two UARTs.
Figure 44. UART Transmitter
DATA BUS
XTAL
BAUD RATE
GENERATOR
BAUD x 16
UART I/O DATA
REGISTER (UDRn)
/16
STORE UDRn
SHIFT ENABLE
PIN CONTROL
LOGIC
BAUD
CONTROL LOGIC
TXDn
10(11)-BIT TX
SHIFT REGISTER
PD1/
PB3
n = 0,1
DATA BUS
U2Xn
MPCMPn
TXCn
UDREn
FEn
ORn
RXCn
UART CONTROL AND
STATUS REGISTER
(UCSRnA)
UDREn
UDRIEn
RXCIEn
TXCIEn
UART CONTROL AND
STATUS REGISTER
(UCSRnB)
TXCn
RXENn
TXENn
CHR9n
RXB8n
TXB8n
IDLE
TXCn
IRQ
UDREn
IRQ
Data transmission is initiated by writing the data to be transmitted to the UART I/O Data
Register, UDRn. Data is transferred from UDRn to the Transmit Shift Register when:
•
A new character has been written to UDRn after the stop bit from the previous
character has been shifted out. The Shift Register is loaded immediately.
69
1228D–AVR–02/07
•
A new character has been written to UDRn before the stop bit from the previous
character has been shifted out. The Shift Register is loaded when the stop bit of the
character currently being transmitted has been shifted out.
If the 10(11)-bit Transmit Shift Register is empty, data is transferred from UDRn to the
Shift Register. At this time the UDREn (UART Data Register Empty) bit in the UART
Control and Status Register, UCSRnA, is set. When this bit is set (one), the UART is
ready to receive the next character. At the same time as the data is transferred from
UDRn to the 10(11)-bit Shift Register, bit 0 of the Shift Register is cleared (start bit) and
bit 9 or 10 is set (stop bit). If 9-bit data word is selected (the CHR9n bit in the UART
Control and Status Register, UCSRnB, is set), the TXB8 bit in UCSRnB is transferred to
bit 9 in the Transmit Shift Register.
On the baud rate clock following the transfer operation to the Shift Register, the start bit
is shifted out on the TXDn pin. Then follows the data, LSB first. When the stop bit has
been shifted out, the Shift Register is loaded if any new data has been written to the
UDRn during the transmission. During loading, UDREn is set. If there is no new data in
the UDRn Register to send when the stop bit is shifted out, the UDREn Flag will remain
set until UDRn is written again. When no new data has been written and the stop bit has
been present on TXDn for one bit length, the TX Complete Flag (TXCn) in UCSRnA
is set.
The TXENn bit in UCSRnB enables the UART Transmitter when set (one). When this bit
is cleared (zero), the PD1 (UART0) or PB3 (UART1) pin can be used for general I/O.
When TXENn is set, the UART Transmitter will be connected to PD1 (UART0) or PB3
(UART1), which is forced to be an output pin regardless of the setting of the DDD1 bit in
DDRD (UART0) or DDB3 in DDRB (UART1). Note that PB3 (UART1) also is used as
one of the input pins to the Analog Comparator. It is therefore not recommended to use
UART1 if the Analog Comparator is also used in the application at the same time.
70
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Data Reception
Figure 45 shows a block diagram of the UART Receiver.
Figure 45. UART Receiver
DATA BUS
XTAL
BAUD RATE
GENERATOR
BAUD x 16
UART I/O DATA
REGISTER (UDRn)
/16
BAUD
STORE UDRn
PIN CONTROL
LOGIC
n = 0,1
UDRIEn
RXCIEn
TXCIEn
UART CONTROL AND
STATUS REGISTER
(UCSRnB)
DATA BUS
TXCn
UDREn
FEn
ORn
RXCn
U2Xn
MPCMPn
10(11)-BIT RX
SHIFT REGISTER
DATA RECOVERY
LOGIC
RXENn
TXENn
CHR9n
RXB8n
TXB8n
RXDn
UART CONTROL AND
STATUS REGISTER
(UCSRnA)
TXCn
PD0/
PB2
RXCn
IRQ
The Receiver front-end logic samples the signal on the RXDn pin at a frequency 16
times the baud rate. While the line is idle, one single sample of logical “0” will be interpreted as the falling edge of a start bit, and the start bit detection sequence is initiated.
Let sample 1 denote the first zero-sample. Following the 1-to-0 transition, the Receiver
samples the RXDn pin at samples 8, 9 and 10. If two or more of these three samples are
found to be logical “1”s, the start bit is rejected as a noise spike and the Receiver starts
looking for the next 1-to-0 transition.
If, however, a valid start bit is detected, sampling of the data bits following the start bit is
performed. These bits are also sampled at samples 8, 9 and 10. The logical value found
in at least two of the three samples is taken as the bit value. All bits are shifted into the
Transmitter Shift Register as they are sampled. Sampling of an incoming character is
shown in Figure 46. Note that the description above is not valid when the UART transmission speed is doubled. See “Double-speed Transmission” on page 78 for a detailed
description.
71
1228D–AVR–02/07
Figure 46. Sampling Received Data(1)
Note:
1. This figure is not valid when the UART speed is doubled. See “Double-speed
Transmission” on page 78 for a detailed description.
When the stop bit enters the Receiver, the majority of the three samples must be one to
accept the stop bit. If two or more samples are logical “0”s, the Framing Error (FEn) Flag
in the UART Control and Status Register (UCSRnA) is set. Before reading the UDRn
Register, the user should always check the FEn bit to detect framing errors.
Whether or not a valid stop bit is detected at the end of a character reception cycle, the
data is transferred to UDRn and the RXCn Flag in UCSRnA is set. UDRn is in fact two
physically separate registers, one for transmitted data and one for received data. When
UDRn is read, the Receive Data Register is accessed, and when UDRn is written, the
Transmit Data Register is accessed. If 9-bit data word is selected (the CHR9n bit in the
UART Control and Status Register [UCSRnB] is set), the RXB8n bit in UCSRnB is
loaded with bit 9 in the Transmit Shift Register when data is transferred to UDRn.
If, after having received a character, the UDRn Register has not been read since the last
receive, the OverRun (ORn) Flag in UCSRnB is set. This means that the last data byte
shifted into the Shift Register could not be transferred to UDRn and has been lost. The
ORn bit is buffered and is updated when the valid data byte in UDRn is read. Thus, the
user should always check the ORn bit after reading the UDRn Register in order to detect
any overruns if the baud rate is high or CPU load is high.
When the RXEN bit in the UCSRnB Register is cleared (zero), the Receiver is disabled.
This means that the PD0 pin can be used as a general I/O pin. When RXEN is set, the
UART Receiver will be connected to PD0 (UART0) or PB2 (UART1), which is forced to
be an input pin regardless of the setting of the DDD0 in DDRD (UART0) or DDB2 bit in
DDRB (UART1). When PD0 (UART0) or PB2 (UART1) is forced to input by the UART,
the PORTD0 (UART0) or PORTB2 (UART1) bit can still be used to control the pull-up
resistor on the pin.
Note that PB2 (UART1) also is used as one of the input pins to the Analog Comparator.
It is therefore not recommended to use UART1 if the Analog Comparator also is used in
the application at the same time.
When the CHR9n bit in the UCSRnB Register is set, transmitted and received characters are nine bits long plus start and stop bits. The ninth data bit to be transmitted is the
TXB8n bit in UCSRnB Register. This bit must be set to the wanted value before a transmission is initiated by writing to the UDRn Register. The ninth data bit received is the
RXB8n bit in the UCSRnB Register.
72
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Multi-processor
Communication Mode
The Multi-processor Communication mode enables several Slave MCUs to receive data
from a master MCU. This is done by first decoding an address byte to find out which
MCU has been addressed. If a particular Slave MCU has been addressed, it will receive
the following data bytes as normal, while the other Slave MCUs will ignore the data
bytes until another address byte is received.
For an MCU to act as a master MCU, it should enter 9-bit transmission mode (CHR9n in
UCSRnB set). The ninth bit must be one to indicate that an address byte is being transmitted, and zero to indicate that a data byte is being transmitted.
For the Slave MCUs, the mechanism appears slightly different for 8-bit and 9-bit reception mode. In 8-bit reception mode (CHR9n in UCSRnB cleared), the stop bit is one for
an address byte and zero for a data byte. In 9-bit reception mode (CHR9n in UCSRnB
set), the ninth bit is one for an address byte and zero for a data byte, whereas the stop
bit is always high.
The following procedure should be used to exchange data in Multi-processor Communication mode:
1. All Slave MCUs are in Multi-processor Communication mode (MPCMn in UCSRnA is set).
2. The master MCU sends an address byte and all Slaves receive and read this
byte. In the Slave MCUs, the RXCn Flag in UCSRnA will be set as normal.
3. Each Slave MCU reads the UDRn Register and determines if it has been
selected. If so, it clears the MPCMn bit in UCSRnA; otherwise, it waits for the
next address byte.
4. For each received data byte, the receiving MCU will set the Receive Complete
Flag (RXCn in UCSRnA). In 8-bit mode, the receiving MCU will also generate a
framing error (FEn in UCSRnA set), since the stop bit is zero. The other Slave
MCUs, which still have the MPCMn bit set, will ignore the data byte. In this case,
the UDRn Register and the RXCn, FEn, or Flags will not be affected.
5. After the last byte has been transferred, the process repeats from step 2.
UART Control
UART0 I/O Data Register –
UDR0
UART1 I/O Data Register –
UDR1
Bit
7
6
5
4
3
2
1
0
$0C ($2C)
MSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
Bit
LSB
UDR0
0
$03 ($23)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
UDR1
The UDRn Register is actually two physically separate registers sharing the same I/O
address. When writing to the register, the UART Transmit Data Register is written.
When reading from UDRn, the UART Receive Data Register is read.
UART0 Control and Status
Registers – UCSR0A
Bit
7
6
5
4
3
2
1
0
$0B ($2B)
RXC0
TXC0
UDRE0
FE0
OR0
–
U2X0
MPCM0
Read/Write
R
R/W
R
R
R
R
R/W
R/W
Initial Value
0
0
1
0
0
0
0
0
UCSR0A
73
1228D–AVR–02/07
UART1 Control and Status
Registers – UCSR1A
Bit
7
6
5
4
3
2
1
0
RXC1
TXC1
UDRE1
FE1
OR1
–
U2X1
MPCM1
Read/Write
R
R/W
R
R
R
R
R/W
R/W
Initial Value
0
0
1
0
0
0
0
0
$02 ($22)
UCSR1A
• Bit 7 – RXC0/RXC1: UART Receive Complete
This bit is set (one) when a received character is transferred from the Receiver Shift
Register to UDRn. The bit is set regardless of any detected framing errors. When the
RXCIEn bit in UCSRnB is set, the UART Receive Complete interrupt will be executed
when RXCn is set (one). RXCn is cleared by reading UDRn. When interrupt-driven data
reception is used, the UART Receive Complete Interrupt routine must read UDRn in
order to clear RXCn; otherwise, a new interrupt will occur once the interrupt routine
terminates.
• Bit 6 – TXC0/TXC1: UART Transmit Complete
This bit is set (one) when the entire character (including the stop bit) in the Transmit
Shift Register has been shifted out and no new data has been written to UDRn. This
Flag is especially useful in half-duplex communications interfaces, where a transmitting
application must enter Receive mode and free the communications bus immediately
after completing the transmission.
When the TXCIEn bit in UCSRnB is set, setting of TXCn causes the UART Transmit
Complete interrupt to be executed. TXCn is cleared by hardware when executing the
corresponding Interrupt Handling Vector. Alternatively, the TXCn bit is cleared (zero) by
writing a logical “1” to the bit.
• Bit 5 – UDRE0/UDRE1: UART Data Register Empty
This bit is set (one) when a character written to UDRn is transferred to the Transmit Shift
Register. Setting of this bit indicates that the Transmitter is ready to receive a new character for transmission.
When the UDRIEn bit in UCSRnB is set, the UART Transmit Complete interrupt will be
executed as long as UDREn is set and the global interrupt enable bit in SREG is set.
UDREn is cleared by writing UDRn. When interrupt-driven data transmittal is used, the
UART Data Register Empty Interrupt routine must write UDRn in order to clear UDREn,
otherwise a new interrupt will occur once the interrupt routine terminates.
UDREn is set (one) during reset to indicate that the Transmitter is ready.
• Bit 4 – FE0/FE1: Framing Error
This bit is set if a Framing Error condition is detected, i.e., when the stop bit of an incoming character is zero.
The FEn bit is cleared when the stop bit of received data is one.
• Bit 3 – OR0/OR1: OverRun
This bit is set if an Overrun condition is detected, i.e., when a character already present
in the UDRn Register is not read before the next character has been shifted into the
Receiver Shift Register. The ORn bit is buffered, which means that it will be set once the
valid data still in UDRn is read.
The ORn bit is cleared (zero) when data is received and transferred to UDRn.
74
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Bit 2 – Res: Reserved Bit
This bit is reserved bit in the ATmega161 and will always read as zero.
• Bit 1 – U2X0/U2X1: Double the UART Transmission Speed
When this bit is set (one), the UART speed will be doubled. This means that a bit will be
transmitted/received in 8 CPU clock periods instead of 16 CPU clock periods. For a
detailed description, see “Double-speed Transmission” on page 78.
• Bit 0 – MPCM0/MPCM1: Multi-processor Communication Mode
This bit is used to enter Multi-processor Communication mode. The bit is set when the
Slave MCU waits for an address byte to be received. When the MCU has been
addressed, the MCU switches off the MPCMn bit and starts data reception.
For a detailed description, see “Multi-processor Communication mode”.
UART0 Control and Status
Registers – UCSR0B
UART1 Control and Status
Registers – UCSR1B
Bit
7
6
5
4
3
2
1
0
$0A ($2A)
RXCIE0
TXCIE0
UDRIE0
RXEN0
TXEN0
CHR90
RXB80
TXB80
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
Initial Value
0
0
0
0
0
0
1
0
Bit
7
6
5
4
3
2
1
0
RXCIE1
TXCIE1
UDRIE1
RXEN1
TXEN1
CHR91
RXB81
TXB81
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
Initial Value
0
0
0
0
0
0
1
0
$01 ($21)
UCSR0B
UCSR1B
• Bit 7 – RXCIE0/RXCIE1: RX Complete Interrupt Enable
When this bit is set (one), a setting of the RXCn bit in UCSRnA will cause the Receive
Complete interrupt routine to be executed, provided that global interrupts are enabled.
• Bit 6 – TXCIE0/TXCIE1: TX Complete Interrupt Enable
When this bit is set (one), a setting of the TXCn bit in UCSRnA will cause the Transmit
Complete interrupt routine to be executed, provided that global interrupts are enabled.
• Bit 5 – UDRIE0/UDREI1: UART Data Register Empty Interrupt Enable
When this bit is set (one), a setting of the UDREn bit in UCSRnA will cause the UART
Data Register Empty interrupt routine to be executed, provided that global interrupts are
enabled.
• Bit 4 – RXEN0/RXEN1: Receiver Enable
This bit enables the UART Receiver when set (one). When the Receiver is disabled, the
TXCn, ORn and FEn Status Flags cannot become set. If these flags are set, turning off
RXEN does not cause them to be cleared.
• Bit 3 – TXEN0/TXEN1: Transmitter Enable
This bit enables the UART Transmitter when set (one). When disabling the Transmitter
while transmitting a character, the Transmitter is not disabled before the character in the
Shift Register plus any following character in UDRn has been completely transmitted.
75
1228D–AVR–02/07
• Bit 2 – CHR90/CHR91: 9-bit Characters
When this bit is set (one), transmitted and received characters are nine bits long, plus
start and stop bits. The ninth bit is read and written by using the RXB8n and TXB8 bits in
UCSRnB, respectively. The ninth data bit can be used as an extra stop bit or a parity bit.
• Bit 1 – RXB80/RXB81: Receive Data Bit 8
When CHR9n is set (one), RXB8n is the ninth data bit of the received character.
• Bit 0 – TXB80/TXB81: Transmit Data Bit 8
When CHR9n is set (one), TXB8n is the ninth data bit in the character to be transmitted.
Baud Rate Generator
The baud rate generator is a frequency divider that generates baud rates according to
the following equation:
f CK
BAUD = --------------------------------16(UBR + 1 )
•
BAUD = Baud rate
•
fCK= Crystal clock frequency
•
UBR = Contents of the UBRRH and UBRR Registers (0 - 4095)
•
Note that this equation is not valid when the UART transmission speed is doubled.
See “Double-speed Transmission” for a detailed description.
For standard crystal frequencies, the most commonly used baud rates can be generated
by using the UBR settings in Table 24. UBR values that yield an actual baud rate differing less than 2% from the target baud rate are boldface in the table. However, using
baud rates that have more than 1% error is not recommended. High error ratings give
less noise resistance.
76
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 24. UBR Settings at Various Crystal Frequencies
Baud Rate
1 MHz %Error 1.8432 MHz %Error
2 MHz %Error 2.4576 MHz %Error
2400 UBR=
25
0.2 UBR=
47
0.0 UBR=
51
0.2 UBR=
63
0.0
4800 UBR=
12
0.2 UBR=
23
0.0 UBR=
25
0.2 UBR=
31
0.0
6
7.5 UBR=
9600 UBR=
11
0.0 UBR=
12
0.2 UBR=
15
0.0
3
7.8 UBR=
8
3.7 UBR=
10
3.1
14400 UBR=
7
0.0 UBR=
2
7.8 UBR=
6
7.5 UBR=
19200 UBR=
5
0.0 UBR=
7
0.0
1
7.8 UBR=
3
7.8 UBR=
4
6.3
28800 UBR=
3
0.0 UBR=
1
22.9 UBR=
2
7.8 UBR=
38400 UBR=
2
0.0 UBR=
3
0.0
0
7.8 UBR=
1
7.8 UBR=
2
12.5
57600 UBR=
1
0.0 UBR=
0
22.9 UBR=
1
33.3 UBR=
1
22.9 UBR=
76800 UBR=
1
0.0
0
84.3 UBR=
0
7.8 UBR=
0
25.0
115200 UBR=
0
0.0 UBR=
Baud Rate 3.2768 MHz %Error 3.6864 MHz %Error
4 MHz %Error
4.608 MHz %Error
2400 UBR=
84
0.4 UBR=
95
0.0 UBR=
103
0.2 UBR=
119
0.0
4800 UBR=
42
0.8 UBR=
47
0.0 UBR=
51
0.2 UBR=
59
0.0
9600 UBR=
20
1.6 UBR=
23
0.0 UBR=
25
0.2 UBR=
29
0.0
16
2.1 UBR=
13
1.6 UBR=
15
0.0 UBR=
19
0.0
14400 UBR=
10
3.1 UBR=
19200 UBR=
11
0.0 UBR=
12
0.2 UBR=
14
0.0
8
3.7 UBR=
28800 UBR=
6
1.6 UBR=
7
0.0 UBR=
9
0.0
4
6.3 UBR=
6
7.5 UBR=
7
6.7
38400 UBR=
5
0.0 UBR=
3
12.5 UBR=
3
7.8 UBR=
57600 UBR=
3
0.0 UBR=
4
0.0
2
12.5 UBR=
2
7.8 UBR=
3
6.7
76800 UBR=
2
0.0 UBR=
1
12.5 UBR=
1
7.8 UBR=
2
20.0
115200 UBR=
1
0.0 UBR=
Baud Rate 7.3728 MHz %Error
8 MHz %Error
9.216 MHz %Error 11.059 MHz %Error
287
2400 UBR=
191
0.0 UBR=
207
0.2 UBR=
239
0.0 UBR=
4800 UBR=
95
0.0 UBR=
103
0.2 UBR=
119
0.0 UBR=
143
0.0
9600 UBR=
47
0.0 UBR=
51
0.2 UBR=
59
0.0 UBR=
71
0.0
14400 UBR=
31
0.0 UBR=
34
0.8 UBR=
39
0.0 UBR=
47
0.0
19200 UBR=
23
0.0 UBR=
25
0.2 UBR=
29
0.0 UBR=
35
0.0
16
2.1 UBR=
28800 UBR=
15
0.0 UBR=
19
0.0 UBR=
23
0.0
14
0.0 UBR=
17
0.0
38400 UBR=
11
0.0 UBR=
12
0.2 UBR=
8
3.7 UBR=
57600 UBR=
7
0.0 UBR=
9
0.0 UBR=
11
0.0
6
7.5 UBR=
7
6.7 UBR=
76800 UBR=
5
0.0 UBR=
8
0.0
3
7.8 UBR=
115200 UBR=
3
0.0 UBR=
4
0.0 UBR=
5
0.0
77
1228D–AVR–02/07
UART0 and UART1 High Byte
Baud Rate Register UBRRHI
Bit
$20 ($40)
7
6
5
MSB1
4
3
LSB1
MSB0
2
1
0
LSB0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
UBRRHI
The UART Baud Register is a 12-bit register. The four most significant bits are located in
a separate register, UBRRHI. Note that both UART0 and UART1 share this register. Bit
7 to bit 4 of UBRRHI contain the four most significant bits of the UART1 Baud Register.
Bit 3 to bit 0 contain the four most significant bits of the UART0 Baud Register.
UART0 Baud Rate Register
Low Byte – UBRR0
UART1 Baud Rate Register
Low Byte – UBRR1
Bit
7
6
5
4
3
2
1
0
$09 ($29)
MSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
Bit
LSB
UBRR0
0
$00 ($20)
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
UBRR1
UBRRn stores the eight least significant bits of the UART Baud Rate Register.
Double-speed
Transmission
The ATmega161 provides a separate UART mode that allows the user to double the
communication speed. By setting the U2X bit in UART Control and Status Register
UCSRnA, the UART speed will be doubled. The data reception will differ slightly from
Normal mode. Since the speed is doubled, the Receiver front-end logic samples the signals on RXDn pin at a frequency 8 times the baud rate. While the line is idle, one single
sample of logical “0” will be interpreted as the falling edge of a start bit, and the start bit
detection sequence is initiated. Let sample 1 denote the first zero-sample. Following the
1-to-0 transition, the Receiver samples the RXDn pin at samples 4, 5 and 6. If two or
more of these three samples are found to be logical “1”s, the start bit is rejected as a
noise spike and the Receiver starts looking for the next 1-to-0 transition.
If, however, a valid start bit is detected, sampling of the data bits following the start bit is
performed. These bits are also sampled at samples 4, 5 and 6. The logical value found
in at least two of the three samples is taken as the bit value. All bits are shifted into the
Transmitter Shift Register as they are sampled. Sampling of an incoming character is
shown in Figure 47.
Figure 47. Sampling Received Data when the Transmission Speed is Doubled
RXD
START BIT
D0
D1
D2
D3
D4
D5
D6
D7
STOP BIT
RECEIVER
SAMPLING
78
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
The Baud Rate Generator in
Double UART Speed Mode
Note that the baud rate equation is different from the equation on page 76 when the
UART speed is doubled:
f CK
BAUD = ----------------------------8(UBR + 1 )
•
BAUD = Baud rate
•
fCK= Crystal Clock frequency
•
UBR = Contents of the UBRRHI and UBRR Registers (0 - 4095)
•
Note that this equation is only valid when the UART transmission speed is doubled.
For standard crystal frequencies, the most commonly used baud rates can be generated
by using the UBR settings in Table 24. UBR values that yield an actual baud rate differing less than 1.5% from the target baud rate are boldface in the table. However, since
the number of samples are reduced and the system clock might have some variance
(this applies especially when using resonators), it is recommended that the baud rate
error be less than 0.5%.
79
1228D–AVR–02/07
Table 25. UBR Settings at Various Crystal Frequencies in Double-speed Mode
Baud Rate
1.0000 MHz
% Error
1.8432 MHz
% Error
2.0000 MHz
% Error
2400
4800
9600
14400
19200
28800
38400
57600
76800
115200
230400
UBR = 51
UBR = 25
UBR = 12
UBR = 8
UBR = 6
UBR = 3
UBR = 2
UBR = 1
UBR = 1
UBR = 0
-
0.2
0.2
0.2
3.7
7.5
7.8
7.8
7.8
22.9
84.3
-
UBR = 95
UBR = 47
UBR = 23
UBR = 15
UBR = 11
UBR = 7
UBR = 5
UBR = 3
UBR = 2
UBR = 1
UBR = 0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
UBR = 103
UBR = 51
UBR = 25
UBR = 16
UBR = 12
UBR = 8
UBR = 6
UBR = 3
UBR = 2
UBR = 1
UBR = 0
0.2
0.2
0.2
2.1
0.2
3.7
7.5
7.8
7.8
7.8
84.3
Baud Rate
3.2768 MHz
% Error
3.6864 MHz
% Error
4.0000 MHz
% Error
2400
4800
9600
14400
19200
28800
38400
57600
76800
115200
230400
460800
912600
UBR = 170
UBR = 84
UBR = 42
UBR = 27
UBR = 20
UBR = 13
UBR = 10
UBR = 6
UBR = 4
UBR = 3
UBR = 1
UBR = 0
-
0.2
0.4
0.8
1.6
1.6
1.6
3.1
1.6
6.2
12.5
12.5
12.5
-
UBR = 191
UBR = 95
UBR = 47
UBR = 31
UBR = 23
UBR = 15
UBR = 11
UBR = 7
UBR = 5
UBR = 3
UBR = 1
UBR = 0
-
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
-
UBR = 207
UBR = 103
UBR = 51
UBR = 34
UBR = 25
UBR = 16
UBR = 12
UBR = 8
UBR = 6
UBR = 3
UBR = 1
UBR = 0
UBR = 0
0.2
0.2
0.2
0.8
0.2
2.1
0.2
3.7
7.5
7.8
7.8
7.8
84.3
Baud Rate
7.3728 MHz
% Error
8.0000 MHz
% Error
9.2160 MHz
% Error
2400
4800
9600
14400
19200
28800
38400
57600
76800
115200
230400
460800
912600
UBR = 383
UBR = 191
UBR = 95
UBR = 63
UBR = 47
UBR = 31
UBR = 23
UBR = 15
UBR = 11
UBR = 7
UBR = 3
UBR = 1
UBR = 0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
UBR = 416
UBR = 207
UBR = 103
UBR = 68
UBR = 51
UBR = 34
UBR = 25
UBR = 16
UBR = 12
UBR = 8
UBR = 3
UBR = 1
UBR = 0
0.1
0.2
0.2
0.6
0.2
0.8
0.2
2.1
0.2
3.7
7.8
7.8
7.8
UBR = 479
UBR = 239
UBR = 119
UBR = 79
UBR = 59
UBR = 39
UBR = 29
UBR = 19
UBR = 14
UBR = 9
UBR = 4
UBR = 2
UBR = 0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
20.0
20.0
80
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Analog Comparator
The Analog Comparator compares the input values on the positive input PB2 (AIN0) and
negative input PB3 (AIN1). When the voltage on the positive input PB2 (AIN0) is higher
than the voltage on the negative input PB3 (AIN1), the Analog Comparator Output
(ACO) is set (one). The comparator’s output can be set to trigger the Timer/Counter1
Input Capture function. In addition, the comparator can trigger a separate interrupt,
exclusive to the Analog Comparator. The user can select interrupt triggering on comparator output rise, fall or toggle. A block diagram of the comparator and its surrounding
logic is shown in Figure 48.
Figure 48. Analog Comparator Block Diagram
Analog Comparator Control
and Status Register – ACSR
Bit
7
6
5
4
3
2
1
0
$08 ($28)
ACD
AINBG
ACO
ACI
ACIE
ACIC
ACIS1
ACIS0
Read/Write
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
N/A
0
0
0
0
0
ACSR
• Bit 7 – ACD: Analog Comparator Disable
When this bit is set (one), the power to the Analog Comparator is switched off. This bit
can be set at any time to turn off the Analog Comparator. This will reduce power consumption in active and Idle mode. When changing the ACD bit, the Analog Comparator
Interrupt must be disabled by clearing the ACIE bit in ACSR. Otherwise, an interrupt can
occur when the bit is changed.
• Bit 6 – AINBG: Analog Comparator Bandgap Select
When this bit is set, a fixed bandgap voltage of 1.22 ± 0.05V replaces the normal input
to the positive input (AIN0) of the comparator. When this bit is cleared, the normal input
pin PB2 is applied to the positive input of the comparator.
• Bit 5 – ACO: Analog Comparator Output
ACO is directly connected to the comparator output.
81
1228D–AVR–02/07
• Bit 4 – ACI: Analog Comparator Interrupt Flag
This bit is set (one) when a comparator output event triggers the interrupt mode defined
by ACI1 and ACI0. The Analog Comparator Interrupt routine is executed if the ACIE bit
is set (one) and the I-bit in SREG is set (one). ACI is cleared by hardware when executing the corresponding Interrupt Handling Vector. Alternatively, ACI is cleared by writing
a logical “1” to the Flag.
• Bit 3 – ACIE: Analog Comparator Interrupt Enable
When the ACIE bit is set (one) and the I-bit in the Status Register is set (one), the Analog Comparator Interrupt is enabled. When cleared (zero), the interrupt is disabled.
• Bit 2 – ACIC: Analog Comparator Input Capture Enable
When set (one), this bit enables the Input Capture function in Timer/Counter1 to be triggered by the Analog Comparator. The comparator output is, in this case, directly
connected to the Input Capture front-end logic, making the comparator utilize the noise
canceler and edge select features of the Timer/Counter1 Input Capture Interrupt. When
cleared (zero), no connection between the Analog Comparator and the Input Capture
function is given. To make the comparator trigger the Timer/Counter1 Input Capture
Interrupt, the TICIE1 bit in the Timer Interrupt Mask Register (TIMSK) must be set (one).
• Bits 1, 0 – ACIS1, ACIS0: Analog Comparator Interrupt Mode Select
These bits determine which comparator events trigger the Analog Comparator Interrupt.
The different settings are shown in Table 26.
Table 26. ACIS1/ACIS0 Settings(1)
ACIS1
ACIS0
0
0
Comparator Interrupt on Output Toggle
0
1
Reserved
1
0
Comparator Interrupt on Falling Output Edge
1
1
Comparator Interrupt on Rising Output Edge
Note:
Interrupt Mode
1. When changing the ACIS1/ACIS0 bits, the Analog Comparator Interrupt must be disabled by clearing its Interrupt Enable bit in the ACSR Register. Otherwise, an
interrupt can occur when the bits are changed.
Caution: Using the SBI or CBI instruction on bits other than ACI in this register will write
a one back into ACI if it is read as set, thus clearing the Flag.
The Analog Comparator pins (PB2 and PB3) are also used as the TXD1 and RXD1 pins
for UART1. Note that if the UART1 transceiver or Receiver is enabled, the UART1 will
override the settings in the DDRB Register even if the Analog Comparator is enabled.
Therefore, it is not recommended to use UART1 if the Analog Comparator is needed in
the same application at the same time. See “UARTs” on page 69 for more details.
82
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Internal Voltage
Reference
ATmega161 features an internal voltage reference with a nominal voltage of 1.22V. This
reference can be used as an input to the Analog Comparator.
Voltage Reference
The voltage reference has a start-up time that may have an influence on the way it
Enable Signals and Start- should be used. The maximum start-up time is TBD. To save power, the reference is on
only when the AINBG bit in ACSR is set. Thus the user must always allow the reference
up Time
to start up before the output from the Analog Comparator is used. The bandgap reference uses approximately 10 µA, and to reduce the power consumption in Power-down
mode, the user can turn off the reference when entering this mode.
83
1228D–AVR–02/07
Interface to External
Memory
MCU Control Register –
MCUCR
Extended MCU Control
Register – EMCUCR
With all the features the external memory interface provides, it is well suited to operate
as an interface to memory devices such as external SRAM and Flash, and peripherals
such as LCD display, A/D, D/A, etc. The control bits for the external memory interface
are located in two registers, the MCU Control Register (MCUCR) and the Extended
MCU Control Register (EMCUCR).
Bit
7
6
5
4
3
2
1
0
$35 ($55)
SRE
SRW10
SE
SM1
ISC11
ISC10
ISC01
ISC00
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$36 ($56)
SM0
SRL2
SRL1
SRL0
SRW01
SRW00
SRW11
ISC20
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
MCUCR
EMCUCR
• Bit 7 MCUCR – SRE: External SRAM Enable
When the SRE bit is set (one), the external memory interface is enabled and the pin
functions AD0 - 7 (Port A), A8 - 15 (Port C), ALE (Port E), WR and RD (Port D) are activated as the alternate pin functions. The SRE bit overrides any pin direction settings in
the respective Data Direction Registers. See Figure 50 through Figure 53 for a description of the external memory pin functions. When the SRE bit is cleared (zero), the
external Data memory interface is disabled and the normal pin and data direction settings are used
• Bits 6..4 EMCUCR – SRL2, SRL1, SRL0: Wait State Page Limit
It is possible to configure different wait states for different external memory addresses.
The external memory address space can be divided into two pages with different wait
state bits. The SRL2, SRL1 and SRL0 bits select the split of the pages (see Table 28
and Figure 49). As defaults, the SRL2, SRL1 and SRL0 bits are set to zero and the
entire external memory address space is treated as one page. When the entire SRAM
address space is configured as one page, the wait states are configured by the SRW11
and SRW10 bits.
• Bit 1 EMCUCR and Bit 6 MCUCR – SRW11, SRW10: Wait State Select Bits for
Upper Page
The SRW11 and SRW10 bits control the number of wait states for the upper page of the
external memory address space (see Table 27). Note that if the SRL2, SRL1, and SRL0
bits are set to zero, the SRW11 and SRW10 bit settings will define the wait state of the
entire SRAM address space.
84
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Bits 3..2 EMCUCR – SRW01, SRW00: Wait State Select Bits for Lower Page
The SRW01 and SRW00 bits control the number of wait states for the lower page of the
external memory address space (see Table 27).
Table 27. Wait States(1)
SRWn1
SRWn0
0
0
No wait states
0
1
Wait one cycle during read/write strobe
1
0
Wait two cycles during read/write strobe
1
1
Wait two cycles during read/write and wait one cycle before driving
out new address
Note:
Wait States
1. n = 0 or 1 (lower/upper page)
For further details of the timing and wait states of the external memory interface, see
Figure 50 through Figure 53 for how the setting of the SRW bits affects the timing.
Table 28. Page Limits with Different Settings of SRL2..0
SRL2
SRL1
SRL0
Page Limits
0
0
0
Lower page = N/A
Upper page = $0460-$FFFF
0
0
1
Lower page = $0460-$1FFF
Upper page = $2000-$FFFF
0
1
0
Lower page = $0460-$4FFF
Upper page = $4000-$FFFF
0
1
1
Lower page = $0460-$5FFF
Upper page = $6000-$FFFF
1
0
0
Lower page = $0460-$7FFF
Upper page = $8000-$FFFF
1
0
1
Lower page = $0460-$9FFF
Upper page = $A000-$FFFF
1
1
0
Lower page = $0460-$BFFF
Upper page = $C000-$FFFF
1
1
1
Lower page = $0460-$DFFF
Upper page = $E000-$FFFF
85
1228D–AVR–02/07
Figure 49. External Memory with Page Select
Data Memory
$0000
Internal memory
$0460
Lower page
SRW01
SRW00
SRL[2..0]
External Memory
(0-63K x 8)
Upper page
SRW11
SRW10
$FFFF
Figure 50. External Data Memory Cycles without Wait State (SRWn1 = 0 and SRWn0
=0)(1)
T1
T2
T3
T4
System Clock Ø
Prev. addr.
XX
Data/Address [7..0]
Prev. data
XX
Address
Prev. data
XX
Address
XX
Address
XX
Data
XX
Write
Address [15..8]
Data
XX
Read
ALE
WR
Data/Address [7..0]
RD
Note:
86
1. SRWn1 = SRW11 (upper page) or SRW01 (lower page), SRWn0 = SRW10 (upper
page) or SRW00 (lower page).
The ALE pulse in period T4 is only present if the next instruction accesses the RAM
(internal or external). The Data and Address will only change in T4 if ALE is present
(the next instruction accesses the RAM).
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 51. External Data Memory Cycles with SRWn1 = 0 and SRWn0 = 1(1)
T1
T2
T4
T3
T5
System Clock Ø
Prev. addr.
XX
Data/Address [7..0]
Prev. data
XX
Address
Prev. data
XX
Address
XX
Address
XX
Data
XX
Write
Address [15..8]
Data
XX
Read
ALE
WR
Data/Address [7..0]
RD
Note:
1. SRWn1 = SRW11 (upper page) or SRW01 (lower page), SRWn0 = SRW10 (upper
page) or SRW00 (lower page). The ALE pulse in period T5 is only present if the next
instruction accesses the RAM (internal or external). The Data and Address will only
change in T5 if ALE is present (the next instruction accesses the RAM).
Figure 52. External Data Memory Cycles with SRWn1 = 1 and SRWn0 = 0(1)
T1
T2
T4
T3
T6
T5
System Clock Ø
Address [15..8]
Prev. addr.
XX
Data/Address [7..0]
Prev. data
XX
Address
Prev. data
XX
Address
XX
Address
XX
Data
XX
Data
XX
Write
ALE
Read
WR
Data/Address [7..0]
RD
Note:
1. SRWn1 = SRW11 (upper page) or SRW01 (lower page), SRWn0 = SRW10 (upper
page) or SRW00 (lower page). The ALE pulse in period T6 is only present if the next
instruction accesses the RAM (internal or external). The Data and Address will only
change in T6 if ALE is present (the next instruction accesses the RAM).
Figure 53. External Data Memory Cycles with SRWn1 = 1 and SRWn0 = 1(1)
T1
T2
T3
T4
T5
T6
T7
System Clock Ø
Address [15..8]
Prev. addr.
XX
Data/Address [7..0]
Prev. data
XX
Address
Prev. data
XX
Address
XX
Address
XX
Data
XX
Data
XX
Write
ALE
Data/Address [7..0]
Read
WR
RD
Note:
1. SRWn1 = SRW11 (upper page) or SRW01 (lower page), SRWn0 = SRW10 (upper
page) or SRW00 (lower page). The ALE pulse in period T7 is only present if the next
instruction accesses the RAM (internal or external). The Data and Address will only
change in T7 if ALE is present (the next instruction accesses the RAM).
87
1228D–AVR–02/07
Using the External
Memory Interface
The interface consists of:
Port A: multiplexed low-order address bus and data bus
Port C: high-order address bus
The ALE pin: address latch enable
The RD and WR pin: read and write strobes
The external memory interface is enabled by setting the external SRAM enable bit
(SRE) of the MCU Control Register (MCUCR) and will override the setting of the Data
Direction Registers DDRA, DDRD and DDRE. When the SRE bit is cleared (zero), the
external memory interface is disabled and the normal pin and data direction settings are
used. When SRE is low, the address space above the internal SRAM boundary is not
mapped into the internal SRAM, as in AVR parts do not have an external memory
interface.
When ALE goes from high to low, there is a valid address on Port A. ALE is low during a
data transfer. RD and WR are active when accessing the external memory only.
When the external memory interface is enabled, the ALE signal may have short pulses
when accessing the internal RAM, but the ALE signal is stable when accessing the
external memory.
Figure 54 sketches how to connect an external SRAM to the AVR using eight latches
that are transparent when G is high.
Figure 54. External SRAM Connected to the AVR
D[7:0]
Port A
D
ALE
G
AVR
Port C
RD
WR
Q
A[7:0]
SRAM
A[15:8]
RD
WR
For details on the timing for the SRAM interface, please see Figure 83 through Figure 86
and Table 51 through Table 58.
88
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
I/O Ports
All AVR ports have true read-modify-write functionality when used as general digital I/O
ports. This means that the direction of one port pin can be changed without unintentionally changing the direction of any other pin with the SBI and CBI instructions. The same
applies for changing drive value (if configured as output) or enabling/disabling of pull-up
resistors (if configured as input).
Port A
Port A is an 8-bit bi-directional I/O port.
Three I/O memory address locations are allocated for the Port A, one each for the Data
Register – PORTA, $1B($3B), Data Direction Register – DDRA, $1A($3A) and the Port
A Input Pins – PINA, $19($39). The Port A Input Pins address is read-only, while the
Data Register and the Data Direction Register are read/write.
All port pins have individually selectable pull-up resistors. The Port A output buffers can
sink 20 mA and thus drive LED displays directly. When pins PA0 to PA7 are used as
inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated.
The Port A pins have alternate functions related to the optional external memory interface. Port A can be configured to be the multiplexed low-order address/data bus during
accesses to the external Data memory. In this mode, Port A has internal pull-up
resistors.
When Port A is set to the alternate function by the SRE (External SRAM Enable) bit in
the MCUCR (MCU Control Register), the alternate settings override the Data Direction
Register.
Port A Data Register – PORTA
Bit
Port A Data Direction Register
– DDRA
Port A Input Pins Address –
PINA
7
6
5
4
3
2
1
0
$1B ($3B)
PORTA7
PORTA6
PORTA5
PORTA4
PORTA3
PORTA2
PORTA1
PORTA0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$1A ($3A)
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
PINA7
PINA6
PINA5
PINA4
PINA3
PINA2
PINA1
PINA0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
$19 ($39)
PORTA
DDRA
PINA
The Port A Input Pins address (PINA) is not a register; this address enables access to
the physical value on each Port A pin. When reading PORTA, the Port A Data Latch is
read and when reading PINA, the logical values present on the pins are read.
Port A as General Digital I/O
All eight pins in Port A have equal functionality when used as digital I/O pins.
PAn, general I/O pin: The DDAn bit in the DDRA Register selects the direction of this
pin. If DDAn is set (one), PAn is configured as an output pin. If DDAn is cleared (zero),
PAn is configured as an input pin. If PORTAn is set (one) when the pin is configured as
an input pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the
PORTAn has to be cleared (zero) or the pin has to be configured as an output pin. The
89
1228D–AVR–02/07
Port A pins are tri-stated when a reset condition becomes active, even if the clock is not
running.
Table 29. DDAn Effects on Port A Pins(1)
DDAn
PORTAn
I/O
Pull-up
0
0
Input
No
Tri-state (high-Z)
0
1
Input
Yes
PAn will source current if ext. pulled low.
1
0
Output
No
Push-pull Zero Output
1
1
Output
No
Push-pull One Output
Note:
Port A Schematics
Comment
1. n: 7,6…0, pin number
Note that all port pins are synchronized. The synchronization latch is, however, not
shown in the figure.
Figure 55. Port A Schematic Diagrams (Pins PA0 - PA7)
90
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Port B
Port B is an 8-bit bi-directional I/O port.
Three I/O memory address locations are allocated for the Port B, one each for the Data
Register – PORTB, $18($38), Data Direction Register – DDRB, $17($37) and the Port B
Input Pins – PINB, $16($36). The Port B Input Pins address is read-only, while the Data
Register and the Data Direction Register are read/write.
All port pins have individually selectable pull-up resistors. The Port B output buffers can
sink 20 mA and thus drive LED displays directly. When pins PB0 to PB7 are used as
inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated.
The Port B pins with alternate functions are shown in Table 30.
Table 30. Port B Pin Alternate Functions(1)
Port Pin
Alternate Functions
PB0
OC0 (Timer/Counter0 Compare Match Output)/T0 (Timer/Counter0 External
Counter Input)
PB1
OC2 (Timer/Counter2 Compare Match Output)/T1 (Timer/Counter1 External
Counter Input)
PB2
RXD1 (UART1 Input Line)/AIN0 (Analog Comparator Positive Input)
PB3
TXD1 (UART1 Output Line)/AIN1 (Analog Comparator Negative Input)
PB4
SS (SPI Slave Select Input)
PB5
MOSI (SPI Bus Master Output/Slave Input)
PB6
MISO (SPI Bus Master Input/Slave Output)
PB7
SCK (SPI Bus Serial Clock)
Note:
1. When the pins are used for the alternate function, the DDRB and PORTB Registers
have to be set according to the alternate function description.
Port B Data Register – PORTB
Bit
7
6
5
4
3
2
1
0
PORTB7
PORTB6
PORTB5
PORTB4
PORTB3
PORTB2
PORTB1
PORTB0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$18 ($38)
Port B Data Direction Register
– DDRB
Bit
7
6
5
4
3
2
1
0
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$17 ($37)
Port B Input Pins Address –
PINB
Bit
7
6
5
4
3
2
1
0
PINB7
PINB6
PINB5
PINB4
PINB3
PINB2
PINB1
PINB0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
$16 ($36)
PORTB
DDRB
PINB
The Port B Input Pins address (PINB) is not a register; this address enables access to
the physical value on each Port B pin. When reading PORTB, the Port B Data Latch is
read and when reading PINB, the logical values present on the pins are read.
91
1228D–AVR–02/07
Port B as General Digital I/O
All eight pins in Port B have equal functionality when used as digital I/O pins.
PBn, general I/O pin: The DDBn bit in the DDRB Register selects the direction of this
pin. If DDBn is set (one), PBn is configured as an output pin. If DDBn is cleared (zero),
PBn is configured as an input pin. If PORTBn is set (one) when the pin is configured as
an input pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the
PORTBn has to be cleared (zero) or the pin has to be configured as an output pin. The
Port B pins are tri-stated when a reset condition becomes active, even if the clock is not
running.
Table 31. DDBn Effects on Port B Pins(1)
DDBn
PORTBn
I/O
Pull-up
0
0
Input
No
Tri-state (high-Z)
0
1
Input
Yes
PBn will source current if ext. pulled low.
1
0
Output
No
Push-pull Zero Output
1
1
Output
No
Push-pull One Output
Note:
Alternate Functions of Port B
Comment
1. n: 7,6…0, pin number
The alternate pin configuration is as follows:
• SCK – Port B, Bit 7
SCK: Master clock output, Slave clock input pin for SPI channel. When the SPI is
enabled as a Slave, this pin is configured as an input regardless of the setting of DDB7.
When the SPI is enabled as a master, the data direction of this pin is controlled by
DDB7. When the pin is forced to be an input, the pull-up can still be controlled by the
PORTB7 bit. See the description of the SPI port for further details.
• MISO – Port B, Bit 6
MISO: Master data input, Slave data output pin for SPI channel. When the SPI is
enabled as a master, this pin is configured as an input regardless of the setting of
DDB6. When the SPI is enabled as a Slave, the data direction of this pin is controlled by
DDB6. When the pin is forced to be an input, the pull-up can still be controlled by the
PORTB6 bit. See the description of the SPI port for further details.
• MOSI – Port B, Bit 5
MOSI: SPI Master data output, Slave data input for SPI channel. When the SPI is
enabled as a Slave, this pin is configured as an input regardless of the setting of DDB5.
When the SPI is enabled as a master, the data direction of this pin is controlled by
DDB5. When the pin is forced to be an input, the pull-up can still be controlled by the
PORTB5 bit. See the description of the SPI port for further details.
• SS – Port B, Bit 4
SS: Slave port select input. When the SPI is enabled as a Slave, this pin is configured
as an input regardless of the setting of DDB5. As a Slave, the SPI is activated when this
pin is driven low. When the SPI is enabled as a master, the data direction of this pin is
controlled by DDB5. When the pin is forced to be an input, the pull-up can still be controlled by the PORTB5 bit. See the description of the SPI port for further details.
92
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• TXD1/AIN1 – Port B, Bit 3
AIN1, Analog Comparator Negative Input. This pin also serves as the negative input of
the On-chip Analog Comparator.
TXD1, Transmit Data (Data output pin for the UART1). When the UART1 Transmitter is
enabled, this pin is configured as an output regardless of the value of DDRB3.
• RXD1/AIN0 – Port B, Bit 2
AIN0, Analog Comparator Positive Input. This pin also serves as the positive input of the
On-chip Analog Comparator.
RXD1, Receive Data (Data input pin for the UART1). When the UART1 Receiver is
enabled, this pin is configured as an input regardless of the value of DDRB2. When the
UART1 forces this pin to be an input, a logical “1” in PORTB2 will turn on the internal
pull-up.
• OC2/T1 – Port B, Bit 1
T1: Timer/Counter1 counter source. See “Timer/Counter1” on page 49 for further
details.
OC2, Output compare match output: The PB1 pin can serve as an external output when
the Timer/Counter2 compare matches. The PB1 pin has to be configured as an output
(DDB1 set [one]) to serve this function. See “8-bit Timer/Counters T/C0 and T/C2” on
page 40 for further details. The OC2 pin is also the output pin for the PWM mode timer
function.
• OC0/T0 – Port B, Bit 0
T0: Timer/Counter0 counter source. See “8-bit Timer/Counters T/C0 and T/C2” on page
40 further details.
OC0, Output compare match output: The PB0 pin can serve as an external output when
the Timer/Counter0 compare matches. The PB0 pin has to be configured as an output
(DDB0 set [one]) to serve this function. See “8-bit Timer/Counters T/C0 and T/C2” on
page 40 for further details and how to enable the output. The OC0 pin is also the output
pin for the PWM mode timer function.
93
1228D–AVR–02/07
Port B Schematics
Note that all port pins are synchronized. The synchronization latches are, however, not
shown in the figures.
Figure 56. Port B Schematic Diagram (Pins PB0 and PB1)
DDBn
PBn
PORTBn
COMx0
COMx1
WP: WRITE PORTB
WD: WRITE DDRB
RL:
READ PORTB LATCH
RP:
READ PORTB PIN
RD: READ DDRB
n:
0,1
x:
0,2
COMP. MATCH x
PWMx
FOCx
CSn2 CSn1 CSn0
94
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 57. Port B Schematic Diagram (Pin PB2)
RD
MOS
PULLUP
RESET
Q
D
DDB2
C
DATA BUS
WD
RESET
Q
D
PORTB2
C
PB2
RL
WP
RP
RXEN1
RXD1
WP:
WD:
RL:
RP:
RD:
RXD1:
RXEN1:
AIN0:
WRITE PORTB
WRITE DDRB
READ PORTB LATCH
READ PORTB PIN
READ DDRB
UART1 RECEIVE DATA
UART1 RECEIVE ENABLE
ANALOG COMPARATOR POSITIVE INPUT
AIN0
Figure 58. Port B Schematic Diagram (Pin PB3)
RD
MOS
PULLUP
RESET
Q
R
D
DDB3
C
DATA BUS
WD
RESET
R
Q
D
PORTB3
PB3
C
RL
WP
RP
TXEN1
TXD1
WP:
WD:
RL:
RP:
RD:
TXD1:
TXEN1:
AIN1:
WRITE PORTB
WRITE DDRB
READ PORTB LATCH
READ PORTB PIN
READ DDRB
UART1 TRANSMIT DATA
UART1 TRANSMIT ENABLE
ANALOG COMPARATOR NEGATIVE INPUT
AIN1
95
1228D–AVR–02/07
Figure 59. Port B Schematic Diagram (Pin PB4)
RD
MOS
PULLUP
RESET
Q
D
DDB4
C
DATA BUS
WD
RESET
Q
D
PORTB4
C
PB4
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
MSTR:
SPE:
MSTR
SPE
WRITE PORTB
WRITE DDRB
READ PORTB LATCH
READ PORTB PIN
READ DDRB
SPI MASTER ENABLE
SPI ENABLE
SPI SS
Figure 60. Port B Schematic Diagram (Pin PB5)
RD
MOS
PULLUP
RESET
Q
R
D
DDB5
WD
RESET
R
Q
D
PORTB5
PB5
DATA BUS
C
C
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
SPE:
MSTR
WRITE PORTB
WRITE DDRB
READ PORTB LATCH
READ PORTB PIN
READ DDRB
SPI ENABLE
MASTER SELECT
MSTR
SPE
SPI MASTER
OUT
SPI SLAVE
IN
96
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 61. Port B Schematic Diagram (Pin PB6)
RD
MOS
PULLUP
RESET
R
Q
D
DDB6
WD
RESET
R
Q
D
PORTB6
PB6
DATA BUS
C
C
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
SPE:
MSTR
WRITE PORTB
WRITE DDRB
READ PORTB LATCH
READ PORTB PIN
READ DDRB
SPI ENABLE
MASTER SELECT
MSTR
SPE
SPI SLAVE
OUT
SPI MASTER
IN
Figure 62. Port B Schematic Diagram (Pin PB7)
RD
MOS
PULLUP
RESET
Q
R
D
DDB7
WD
RESET
R
Q
D
PORTB7
PB7
DATA BUS
C
C
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
SPE:
MSTR
WRITE PORTB
WRITE DDRB
READ PORTB LATCH
READ PORTB PIN
READ DDRB
SPI ENABLE
MASTER SELECT
MSTR
SPE
SPI ClLOCK
OUT
SPI CLOCK
IN
97
1228D–AVR–02/07
Port C
Port C is an 8-bit bi-directional I/O port.
Three I/O memory address locations are allocated for the Port C, one each for the Data
Register – PORTC, $15($35), Data Direction Register – DDRC, $14($34) and the Port C
Input Pins – PINC, $13($33). The Port C Input Pins address is read-only, while the Data
Register and the Data Direction Register are read/write.
All port pins have individually selectable pull-up resistors. The Port C output buffers can
sink 20 mA and thus drive LED displays directly. When pins PC0 to PC7 are used as
inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated.
The Port C pins have alternate functions related to the optional external memory interface. Port C can be configured to be the high-order address byte during accesses to
external Data memory.
When Port C is set to the alternate function by the SRE (External SRAM Enable) bit in
the MCUCR (MCU Control Register), the alternate settings override the Data Direction
Register.
Port C Data Register – PORTC
Bit
7
6
5
4
3
2
1
0
PORTC7
PORTC6
PORTC5
PORTC4
PORTC3
PORTC2
PORTC1
PORTC0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$15 ($35)
Port C Data Direction Register
– DDRC
Bit
7
6
5
4
3
2
1
0
DDC7
DDC6
DDC5
DDC4
DDC3
DDC2
DDC1
DDC0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$14 ($34)
Port C Input Pins Address –
PINC
Bit
7
6
5
4
3
2
1
0
PINC7
PINC6
PINC5
PINC4
PINC3
PINC2
PINC1
PINC0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
$13 ($33)
PORTC
DDRC
PINC
The Port C Input Pins address (PINC) is not a register; this address enables access to
the physical value on each Port C pin. When reading PORTC, the Port C Data Latch is
read and when reading PINC, the logical values present on the pins are read.
Port C as General Digital I/O
All eight pins in Port C have equal functionality when used as digital I/O pins.
PCn, general I/O pin: The DDCn bit in the DDRC Register selects the direction of this
pin. If DDCn is set (one), PCn is configured as an output pin. If DDCn is cleared (zero),
PCn is configured as an input pin. If PORTCn is set (one) when the pin is configured as
an input pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off,
PORTCn has to be cleared (zero) or the pin has to be configured as an output pin. The
Port C pins are tri-stated when a reset condition becomes active, even if the clock is not
running.
98
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 32. DDCn Effects on Port C Pins(1)
DDCn
PORTCn
I/O
Pull-up
0
0
Input
No
Tri-state (high-Z)
0
1
Input
Yes
PCn will source current if ext. pulled low
1
0
Output
No
Push-pull Zero Output
1
1
Output
No
Push-pull One Output
Note:
Port C Schematics
Comment
1. n: 7, 6,…0, pin number
Note that all port pins are synchronized. The synchronization latch is, however, not
shown in the figure.
Figure 63. Port C Schematic Diagram (Pins PC0 - PC7)
99
1228D–AVR–02/07
Port D
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors.
Three I/O address locations are allocated for the Port D, one each for the Data Register
– PORTD, $12($32), Data Direction Register – DDRD, $11($31) and the Port D Input
Pins – PIND, $10($30). The Port D Input Pins address is read-only, while the Data Register and the Data Direction Register are read/write.
The Port D output buffers can sink 20 mA. As inputs, Port D pins that are externally
pulled low will source current if the pull-up resistors are activated.
Some Port D pins have alternate functions as shown in Table 33.
Table 33. Port D Pin Alternate Functions
Port Pin
Alternate Function
PD0
RXD0 (UART0 Input Line)
PD1
TXD0 (UART0 Output Line)
PD2
INT0 (External Interrupt0 Input)
PD3
INT1 (External Interrupt1 Input)
PD3
TOSC1 (RTC Oscillator Timer/Counter2)
PD5
TOSC2 (RTC Oscillator Timer/Counter2)/OC1A (Timer/Counter1 Output
CompareA Match Output)
PD6
WR (Write Strobe to External Memory)
PD7
RD (Read Strobe to External Memory)
When the PD5 pin is used for the alternate function (OC1A), the DDRD and PORTD
Registers have to be set according to the alternate function description.
Port D Data Register – PORTD
Bit
7
6
5
4
3
2
1
0
PORTD7
PORTD6
PORTD5
PORTD4
PORTD3
PORTD2
PORTD1
PORTD0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$12 ($32)
Port D Data Direction Register
– DDRD
Bit
7
6
5
4
3
2
1
0
DDD7
DDD6
DDD5
DDD4
DDD3
DDD2
DDD1
DDD0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
$11 ($31)
Port D Input Pins Address –
PIND
Bit
7
6
5
4
3
2
1
0
PIND7
PIND6
PIND5
PIND4
PIND3
PIND2
PIND1
PIND0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
$10 ($30)
PORTD
DDRD
PIND
The Port D Input Pins address (PIND) is not a register; this address enables access to
the physical value on each Port D pin. When reading PORTD, the Port D Data Latch is
read and when reading PIND, the logical values present on the pins are read.
Port D as General Digital I/O
100
PDn, general I/O pin: The DDDn bit in the DDRD Register selects the direction of this
pin. If DDDn is set (one), PDn is configured as an output pin. If DDDn is cleared (zero),
PDn is configured as an input pin. If PORTDn is set (one) when configured as an input
pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the PORTDn
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
has to be cleared (zero) or the pin has to be configured as an output pin. The Port D pins
are tri-stated when a reset condition becomes active, even if the clock is not running.
Table 34. DDDn Bits on Port D Pins(1)
DDDn
PORTDn
I/O
Pull-up
0
0
Input
No
Tri-state (high-Z)
0
1
Input
Yes
PDn will source current if ext. pulled low.
1
0
Output
No
Push-pull Zero Output
1
1
Output
No
Push-pull One Output
Notes:
Alternate Functions of Port D
Comment
1. n: 7,6…0, pin number
The alternate pin configuration is as follows:
• RD – Port D, Bit 7
RD is the external Data memory read control strobe.
• WR – Port D, Bit 6
WR is the external Data memory write control strobe.
• OC1 – Port D, Bit 5
OC1, Output compare match output: The PD5 pin can serve as an external output when
the Timer/Counter1 compare matches. The PD5 pin has to be configured as an output
(DDD5 set [one]) to serve this function. See “Timer/Counter1” on page 49 for further
details and how to enable the output. The OC1 pin is also the output pin for the PWM
mode timer function.
• TOSC1/TOSC2 – Port D, Bits 5 and 4
When the AS2 bit in ASSR is set (one) to enable asynchronous clocking of
Timer/Counter2, pins PD5 and PD4 are disconnected from the port. In this mode, a
crystal Oscillator is connected to the pins and the pins cannot be used as I/O pins.
• INT1 – Port D, Bit 3
INT1, External Interrupt source 1: The PD3 pin can serve as an external interrupt source
to the MCU. See “MCU Control Register – MCUCR” on page 34 for further details.
• INT0 – Port D, Bit 2
INT0, External Interrupt source 0: The PD2 pin can serve as an external interrupt source
to the MCU. See “MCU Control Register – MCUCR” on page 34 for further details.
• TXD0 – Port D, Bit 1
Transmit Data (Data output pin for the UART0). When the UART0 Transmitter is
enabled, this pin is configured as an output regardless of the value of DDRD1.
• RXD0 – Port D, Bit 0
Receive Data (Data input pin for the UART0). When the UART Receiver is enabled, this
pin is configured as an input regardless of the value of DDRD0. When the UART0 forces
this pin to be an input, a logical “1” in PORTD0 will turn on the internal pull-up.
101
1228D–AVR–02/07
Port D Schematics
Note that all port pins are synchronized. The synchronization latches are, however, not
shown in the figures.
Figure 64. Port D Schematic Diagram (Pin PD0)
RD
MOS
PULLUP
RESET
Q
D
DDD0
C
DATA BUS
WD
RESET
Q
D
PORTD0
C
PD0
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
RXD0:
RXEN0:
RXEN0
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
UART0 RECEIVE DATA
UART0 RECEIVE ENABLE
RXD0
Figure 65. Port D Schematic Diagram (Pin PD1)
RD
MOS
PULLUP
RESET
Q
R
D
DDD1
C
DATA BUS
WD
RESET
R
Q
D
PORTD1
PD1
C
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
TXD0:
TXEN0:
102
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
UART0 TRANSMIT DATA
UART0 TRANSMIT ENABLE
TXEN0
TXD0
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 66. Port D Schematic Diagram (Pins PD2 and PD3)
WP:
WD:
RL:
RP:
RD:
n:
m:
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
2, 3
0, 1
Figure 67. Port D Schematic Diagram (Pin PD4)
RD
MOS
PULLUP
RESET
Q
R
D
DDD4
WD
RESET
R
Q
D
PORTD4
PD4
DATA BUS
C
C
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
AS2:
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
ASYNCH SELECT T/C2
AS2
T/C2 OSC
AMP INPUT
103
1228D–AVR–02/07
Figure 68. Port D Schematic Diagram (Pin PD5)
COMP. MATCH 1A
PWM10
PWM11
FOC1A
WP:
WD:
RL:
RP:
RD:
AS2
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
ASYNCH SELECT T/C2
Figure 69. Port D Schematic Diagram (Pin PD6)
WP:
WD:
RL:
RP:
RD:
WE:
SRE:
104
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
WRITE ENABLE
EXTERNAL SRAM ENABLE
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 70. Port D Schematic Diagram (Pin PD7)
WP:
WD:
RL:
RP:
RD:
RE:
SRE:
WRITE PORTD
WRITE DDRD
READ PORTD LATCH
READ PORTD PIN
READ DDRD
READ ENABLE
EXTERNAL SRAM ENABLE
105
1228D–AVR–02/07
Port E
Port E is a 3-bit bi-directional I/O port with internal pull-up resistors.
Three I/O address locations are allocated for the Port E, one each for the Data Register
– PORTE, $07($27), Data Direction Register – DDRE, $06($26) and the Port E Input
Pins – PINE, $05($25). The Port E Input Pins address is read-only, while the Data Register and the Data Direction Register are read/write.
The Port E output buffers can sink 20 mA. As inputs, Port E pins that are externally
pulled low will source current if the pull-up resistors are activated.
Port E pins have alternate functions as shown in Table 35.
Table 35. Port E Pin Alternate Functions(1)
Port Pin
Alternate Function
PE0
ICP (Input Capture Pin Timer/Counter1)/INT2 (External Interrupt 2 Input)
PE1
OC1B (Timer/Counter1 Output CompareB Match Output)
PE2
ALE (Address Latch Enable, External Memory)
Note:
1. When the PE1 pin is used for the alternate function, the DDRE and PORTE Registers
have to be set according to the alternate function description.
Port E Data Register – PORTE
Port E Data Direction Register
– DDRE
Port E Input Pins Address –
PINE
Bit
7
6
5
4
3
2
1
0
$07 ($27)
–
–
–
–
–
PORTE2
PORTE1
PORTE0
Read/Write
R
R
R
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$06 ($26)
–
–
–
–
–
DDE2
DDE1
DDE0
Read/Write
R
R
R
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$05 ($25)
–
–
–
–
–
PINE2
PINE1
PINE0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
0
0
0
0
0
N/A
N/A
N/A
PORTE
DDRE
PINE
The Port E Input Pins address (PINE) is not a register; this address enables access to
the physical value on each Port E pin. When reading PORTE, the Port E Data Latch is
read and when reading PINE, the logical values present on the pins are read.
Port E as General Digital I/O
106
PEn, general I/O pin: The DDEn bit in the DDRE Register selects the direction of this
pin. If DDEn is set (one), PEn is configured as an output pin. If DDEn is cleared (zero),
PEn is configured as an input pin. If PORTEn is set (one) when configured as an input
pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the PORTEn
has to be cleared (zero) or the pin has to be configured as an output pin. The Port E pins
are tri-stated when a reset condition becomes active, even if the clock is not running.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 36. DDEn Bits on Port E Pins(1)
DDEn
PORTEn
I/O
Pull-up
0
0
Input
No
Tri-state (high-Z)
0
1
Input
Yes
PEn will source current if ext. pulled low.
1
0
Output
No
Push-pull Zero Output
1
1
Output
No
Push-pull One Output
Note:
Alternate Functions of Port E
Comment
1. n: 2,1,0, pin number.
The alternate pin configuration is as follows:
• OC1B – Port E, Bit 2
OC1B, Output compare match output: The PE2 pin can serve as an external output
when the Timer/Counter1 compare matches. The PE2 pin has to be configured as an
output (DDE2 set [one]) to serve this function. See “Timer/Counter1” on page 49 for further details. The OC1B pin is also the output pin for the PWM mode timer function.
• ALE – Port E, Bit 1
ALE: When the External Memory is enabled, the PE1 pin serves as the Dress Latch
Enable. Note that enabling of External Memory will override both the direction and port
value. See “Interface to External Memory” on page 84 for a detailed description.
• ICP/INT2 – Port E, Bit 0
ICP, Input Capture pin: The PE0 pin can serve as the Input Capture source for
Timer/Counter 1. See page 54 for a detailed description.
INT2, External Interrupt source 2: The PE0 pin can serve as an external interrupt source
to the MCU. See “Extended MCU Control Register – EMCUCR” on page 36 for further
details.
107
1228D–AVR–02/07
Port E Schematics
Figure 71. Port E Schematic Diagram (Pin PE0)
RD
MOS
PULLUP
RESET
Q
R
D
DDE0
C
DATA BUS
WD
RESET
R
Q
D
PORTE0
PE0
C
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
ACIC:
ACO:
WRITE PORTE
WRITE DDRE
READ PORTE LATCH
READ PORTE PIN
READ DDRE
COMPARATOR IC ENABLE
COMPARATOR OUTPUT
0
NOISE CANCELER
EDGE SELECT
ICNC1
ICES1
ICF1
1
ACIC
ACO
'1'
INT2
Q
D
PORTE0
C
R
HW CLEAR
SW CLEAR
ISC2
Figure 72. Port E Schematic Diagram (Pin PE1)
RD
MOS
PULLUP
RESET
R
Q
D
DDE1
WD
RESET
R
Q
D
PORTE1
DATA BUS
C
C
PE1
RL
WP
RP
WP:
WD:
RL:
RP:
RD:
SRE:
ALE:
108
WRITE PORTE
WRITE DDRE
READ PORTE LATCH
READ PORTE PIN
READ DDRE
XRAM ENABLE
ALE PULSE FROM XRAM
SRE
ALE
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 73. Port E Schematic Diagram (Pin PE2)
DDE2
PE2
PORTE2
WP:
WD:
RL:
RP:
RD:
WRITE PORTE
WRITE DDRE
READ PORTE LATCH
READ PORTE PIN
READ DDRE
COM1B0
COM1B1
COMP. MATCH 1B
PWM10
PWM11
FOC1B
109
1228D–AVR–02/07
Memory
Programming
Boot Loader Support
The ATmega161 provides a mechanism for downloading and uploading program code
by the MCU itself. This feature allows flexible application software updates, controlled
by the MCU using a Flash-resident Boot Loader program.
The ATmega161 Flash memory is organized in two main sections:
1. The Application Code section (address $0000 - $1DFF)
2. The Boot Loader section/Boot block (address $1E00 - $1FFF)
Figure 74. Memory Sections
Program Memory
$0000
Application Code section
(7.5K x 16)
Boot Loader section
(512 x 16)
$1DFF
$1E00
$1FFF
The Boot Loader program can use any available data interface and associated protocol,
such as UART serial bus interface, to input or output program code and write (program)
that code into the Flash memory or read the code from the Program memory.
The program Flash memory is divided into pages that each contain 128 bytes. The Boot
Loader Flash section occupies eight pages from $1E00 to $1FFF by 16-bit words.
The Store Program Memory (SPM) instruction can access the entire Flash, but it can
only be executed from the Boot Loader Flash section. If no Boot Loader capability is
needed, the entire Flash is available for application code. The ATmega161 has two separate sets of Boot Lock bits that can be set independently. This gives the user a unique
flexibility to select different levels of protection. The user can elect to:
110
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
• Protect the entire Flash from a software update by the Boot Loader program
• Only protect the Boot Loader section from a software update by the Boot Loader
program
• Only protect the Application Code section from a software update by the Boot Loader
program
• Allow software update in the entire Flash
See Table 37 and Table 38 for further details. The Boot Lock bits can be set in software
and in Serial or Parallel Programming mode, but they can only be cleared by a Chip
Erase command.
Table 37. Boot Lock Bit0 Protection Modes (Application Code Section)(1)
BLB0 Mode
BLB02
BLB01
1
1
1
No restrictions for SPM, LPM accessing Application Code
section
2
1
0
SPM is not allowed to write to the Application Code
section.
3
0
0
SPM is not allowed to write to the Application Code
section, and LPM executing from the Boot Loader section
is not allowed to read from the Application Code section.
4
0
1
LPM executing from the Boot Loader section is not
allowed to read from the Application Code section.
Note:
Protection
1. “1” = unprogrammed, “0” = programmed
Table 38. Boot Lock Bit1 Protection Modes (Boot Loader Section)(1)
BLB1 Mode
BLB12
BLB1
1
1
1
1
No restrictions for SPM, LPM accessing Boot Loader
section
2
1
0
SPM is not allowed to write to the Boot Loader section.
3
0
0
SPM is not allowed to write to the Boot Loader section,
and LPM executing from the Application Code section is
not allowed to read from the Boot Loader section.
4
0
1
LPM executing from the Application Code section is not
allowed to read from the Boot Loader section.
Note:
Protection
1. “1” means unprogrammed, “0” means programmed
Entering the Boot Loader Entering the Boot Loader takes place by a jump or call from the application program.
This may be initiated by some trigger such as a command received via UART or SPI
Program
interface. Alternatively, the Boot Reset Fuse (BOOTRST) can be programmed so that
the Reset Vector is pointing to address $1E00 after a reset. In this case, the Boot
Loader is started after the reset. After the application code is loaded, the program can
start executing the application code. Note that the fuses cannot be changed by the MCU
itself. This means that once the Boot Reset Fuse is programmed, the Reset Vector will
always point to the Boot Loader Reset and the fuse can only be changed through the
serial or parallel programming interface. The BOOTRST fuse can also be locked by programming LB1. When LB1 is programmed it is not possible to change the BOOTRST
fuse unless a Chip Erase command is performed first.
111
1228D–AVR–02/07
Table 39. Boot Reset Fuse, BOOTRST(1)
BOOTRST
Note:
Reset Address
1
Reset Vector = Application Reset (address $0000)
0
Reset Vector = Boot Loader Reset (address $1E00)
1. “1” means unprogrammed, “0” means programmed
Capabilities of the Boot
Loader
The program code within the Boot Loader section has the ability to read from and write
into the entire Flash, including the Boot Loader Memory. This allows the user to update
both the Application code and the Boot Loader code that handles the software update.
The Boot Loader can thus even modify itself, and it can also erase itself from the code if
the feature is not needed anymore. Special care must be taken if the user allows the
Boot Loader section to be updated by leaving Boot Lock bit11 unprogrammed. An accidental write to the Boot Loader itself can corrupt the entire Boot Loader, and further
software updates might be impossible. If it is not needed to change the Boot Loader
software itself, it is recommended that the Boot Lock bit 11 be programmed to protect
the Boot Loader software from software changes.
Self-programming the
Flash
Programming of the Flash is executed one page at a time. The Flash page must be
erased first for correct programming. The general Write Lock (Lock Bit 2) does not control the programming of the Flash memory by SPM instruction. Similarly, the Read/Write
Lock (Lock Bit 1) does not control reading or writing by LPM/SPM, if it is attempted.
The Program memory can only be updated page-by-page, not word by word. One page
is 128 bytes (64 words). The Program memory will be modified by first performing page
erase, then by filling the temporary page buffer one word at a time using SPM, and then
by executing page write. If only part of the page needs to be changed, the other parts
must be stored (for example, in the temporary page buffer) before the erase, and then
be rewritten. The temporary page buffer can be accessed in a random sequence. The
CPU is halted both during page erase and during page write and the SPMEN bit in the
SPMCR Register will be auto-cleared. For future compatibility, however, it is recommended that the user software verify that the SPMEN bit is cleared before starting a new
page erase, page write, or before writing the Lock bits command (see code examples
below). It is essential that the page address used in both the page erase and page write
operation is addressing the same page.
Setting the Boot Loader Lock
bits by SPM
To set the Boot Loader Lock bits, write the desired data to R0, write “1001” to SPMCR,
and execute SPM within four clock cycles after writing SPMCR. The only accessible
Lock bits are the Boot Lock bits that may prevent the Application Code and Boot Loader
sections from any software update by the MCU. See Table 37 and Table 38 for how the
different settings of the Boot Loader bits affect the Flash access.
Bit
7
6
5
4
3
2
1
0
–
–
BLB12
BLB11
BLB02
BLB01
–
–
R0
If bit5 - bit2 in R0 is cleared (zero), the corresponding Boot Lock bit will be programmed
if an SPM instruction is executed within four cycles after BLBSET and SPMEN are set in
SPMCR.
Performing Page Erase by
SPM
112
To execute a page erase, set up the address in the Z-pointer, write “0011” to SPMCR,
and execute SPM within four clock cycles after writing SPMCR. The data in R1 and R0
are ignored. The page address must be written to Z13:Z7. Other bits in the Z-pointer will
be ignored during this operation.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Fill the Temporary Buffer
To write an instruction word, set up the address in the Z-pointer and data in R1:R0, write
“0001” to SPMCR, and execute SPM within four clock cycles after writing SPMCR. The
content of Z6:Z1 is used to address the data in the temporary buffer. Z13:Z7 must point
to the page that is supposed to be written.
Perform a Page Write
To execute a page write, set up the address in the Z-pointer, write “0101” to SPMCR,
and execute SPM within four clock cycles after writing SPMCR. The data in R1 and R0
are ignored. The page address must be written to Z13:Z7. During this operation, Z6:Z0
must be zero to ensure that the page is written correctly. When a page write operation is
completed, the Z-pointer will point to the first word in the successive page.
Code Example
Wait: in
r16,SPMCR ; read SPMCR Register
sbrc r16,SPMEN ; Wait for SPMEN to be cleared (indicates that previous
write operation is completed)
rjmp Wait
; if not cleared, keep waiting
ldi
r16,(1<<PGWRT) + (1<<SPMEN) ; The previous writing is completed,
set up for next erase
out
SPMCR,r16 ; output to register
spm
; start the erase operation
Addressing the FLASH during
Self-programming
The Z-pointer is used to address the SPM commands.
Bit
15
14
13
12
11
10
9
8
$1F ($1F)
Z15
Z14
Z13
Z12
Z11
Z10
Z9
Z8
ZH
$1E ($1E)
Z7
Z6
Z5
Z4
Z3
Z2
Z1
Z0
ZL
7
6
5
4
3
2
1
0
Z15:Z14 always ignored
Z13:Z7
page select, for page erase, page write
Z6:Z1
word select, for filling temp buffer (must be zero during page write operation)
Z0
should be zero for all SPM commands, byte select for the LPM instruction
The only operation that does not use the Z-pointer is setting the Boot Loader Lock bits.
The content of the Z-pointer is ignored and will have no effect on the operation.
Note that the page erase and page write operation are addressed independently. Therefore, it is of major importance that the Boot Loader software addresses the same page in
both the page erase and page write operations.
The LPM instruction also uses the Z-pointer to store the address. Since this instruction
addresses the Flash byte-by-byte, the LSB (bit Z0) of the Z-pointer is also used. See
page 16 for a detailed description.
Accidental writing into Flash program by the SPM instruction is prevented by setting up
an “SPM enable time window”. All accesses are executed by first setting I/O bits, and
then by executing SPM within four clock cycles. The I/O Register that controls the SPM
accesses is defined below.
113
1228D–AVR–02/07
Store Program Memory
Control Register – SPMCR
The Store Program Memory Control Register contains the control bits needed to control
the programming of the Flash from internal code execution.
Bit
7
6
$37 ($57)
–
–
5
Read/Write
R
R
R
Initial Value
0
0
0
4
3
2
1
0
BLBSET
PGWRT
PGERS
SPMEN
R
R/W
R/W
R/W
R/W
0
0
0
0
0
SPMCR
• Bits 7..4 – Res: Reserved Bits
These bits are reserved bits in the ATmega161 and always read as zero.
• Bit 3 – BLBSET: Boot Lock Bit Set
If this bit is set at the same time as SPMEN, the next SPM instruction within four clock
cycles sets Boot Lock bits according to the data in R0. The data in R1 and the address
in the Z-pointer are ignored. The BLBSET bit will auto-clear upon completion of Lock bit
set, or if no SPM instruction is executed within four clock cycles. The CPU is halted during Lock bit setting. Only a chip erase can clear the Lock bits.
An LPM instruction within four cycles after BLBSET and SPMEN are set in the SPMCR
Register will put either the Lock bits or the Fuse bits (depending od the Z0 in the Zpointer) into the destination register. See “Reading the Fuse and Lock bits from Software” for details.
• Bit 2 – PGWRT: Page Write
If this bit is set at the same time as SPMEN, the next SPM instruction within four clock
cycles executes page write, with the data stored in the temporary buffer. The page
address is taken from the high part of the Z-pointer. The data in R1 and R0 are ignored.
The PGWRT bit will auto-clear upon completion of a page write or if no SPM instruction
is executed within four clock cycles. The CPU is halted during the entire page write
operation.
• Bit 1 – PGERS: Page Erase
If this bit is set at the same time as SPMEN, the next SPM instruction within four clock
cycles executes a page erase. The page address is taken from the high part of the Zpointer. The data in R1 and R0 are ignored. The PGERS bit will auto-clear upon completion of a page erase or if no SPM instruction is executed within four clock cycles. The
CPU is halted during the entire page erase operation.
• Bit 0 – SPMEN: Store Program Memory Enable
This bit enables the SPM instruction for the next four clock cycles. If set together with
either BLBSET, PGWRT or PGERS, the following SPM instruction will have a special
meaning (see description above). If only SPMEN is set, the following SPM instruction
will store the value in R1:R0 in the temporary page buffer addressed by the Z-pointer.
The LSB of the Z-pointer is ignored. The SPMEN bit will auto-clear upon completion of
an SPM instruction or if no SPM instruction is executed within four clock cycles.
Writing any combination other than “1001”, “0101”, “0011” or “0001” in the lower four
bits, or writing to the I/O Register when any bits are set, will have no effect.
114
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
EEPROM Write Prevents
Writing to SPMCR
Note that an EEPROM write operation will block all software programming to Flash.
Reading the Fuse and Lock bits from software will also be prevented during the
EEPROM write operation. It is recommended that the user check the status bit (EEWE)
in the EECR Register and verify that the bit is cleared before writing to the SPMCR
Register.
Reading the Fuse and Lock
bits from Software
It is possible to read both the Fuse and Lock bits from software. To read the Lock bits,
load the Z-pointer with $0001 and set the BLBSET and SPMEN bits in SPMCR. If an
LPM instruction is executed within three CPU cycles after the BLBSET and SPMEN bits
are set in SPMCR, the Lock bits will be written to the destination register. The BLBSET
and SPMEN bits will auto-clear upon completion of reading the Lock bits or if no
LPM/SPM instruction is executed within three/four CPU cycles. When BLBSET and
SPMEN are cleared, LPM will work as described in “Constant Addressing Using the
LPM Instruction” on page 16 and in the Instruction Set manual.
Bit
7
6
5
4
3
2
1
0
–
–
BLB12
BLB11
BLB02
BLB01
LB2
LB1
R0/Rd
The algorithm for reading the Fuse bits is similar to the one described above for reading
the Lock bits. But when reading the Fuse bits, load $0000 in the Z-pointer. When an
LPM instruction is executed within three cycles after the BLBSET and SPMEN bits are
set in the SPMCR, the Fuse bits can be read in the destination register as shown below.
Bit
7
6
5
4
3
2
1
0
–
BOOTRST
SPIEN
SUT
–
CKSEL[2]
CKSEL[1]
CKSEL[0]
R0/Rd
Fuse and Lock bits that are programmed will be read as zero.
115
1228D–AVR–02/07
Program Memory
Lock bits
The ATmega161 MCU provides six Lock bits that can be left unprogrammed (“1”) or can
be programmed (“0”) to obtain the additional features listed in Table 40. The Lock bits
can only be erased to “1” with the Chip Erase command.
Table 40. Lock Bit Protection Modes (1)
Memory Lock bits
LB Mode
LB1
LB2
1
1
1
No memory lock features enabled
2
0
1
Further programming of the Flash and EEPROM is
disabled in parallel and Serial Programming modes. The
Fuse bits are locked in both Serial and Parallel
Programming modes.(1)
3
0
0
Further programming and verification of the Flash and
EEPROM is disabled in parallel and Serial Programming
modes. The Fuse bits are locked in both Serial and
Parallel Programming modes.(1)
BLB0 Mode
BLB02
BLB01
1
1
1
No restrictions for SPM, LPM accessing the Application
Code section
2
1
0
SPM is not allowed to write to the Application Code
section.
3
0
0
SPM is not allowed to write to the Application Code
section and LPM executing from Boot Loader section is
not allowed to read from the Application Code section.
4
0
1
LPM executing from the Boot Loader section is not
allowed to read from the Application Code section.
BLB1 Mode
BLB12
BLB11
1
1
1
No restrictions for SPM, LPM accessing the Boot Loader
section
2
1
0
SPM is not allowed to write the Boot Loader section.
3
0
0
SPM is not allowed to write to the Boot Loader section and
LPM executing from the Application Code section is not
allowed to read from the Boot Loader section.
4
0
1
LPM executing from the Application Code section is not
allowed to read from the Boot Loader section.
Note:
Fuse bits
116
Protection Type
1. Program the Fuse bits before programming the Lock bits.
The ATmega161 has six Fuse bits: BOOTRST, SPIEN, SUT, and CKSEL [2:0].
•
When BOOTRST is programmed (“0”), the Reset Vector is set to address $1E00,
which is the first address location in the Boot Loader section of the Flash. If the
BOOTRST is unprogrammed (“1”), the Reset Vector is set to address $0000. Default
value is unprogrammed (“1”).
•
When the SPIEN Fuse is programmed (“0”), Serial Program and Data Downloading
is enabled. Default value is programmed (“0”). The SPIEN Fuse is not accessible in
Serial Programming mode.
•
The SUT Fuse changes the start-up times. Default value is unprogrammed (“1”).
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
•
CKSEL2..0: See Table 4, “Reset Delay Selections(3),” on page 26, for which
combination of CKSEL2..0 to use. Default value is “010”.
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are
locked if Lock bit1 (LB1) or Lock bit2 (LB2) is programmed. Program the Fuse bits
before programming the Lock bits.
Signature Bytes
All Atmel microcontrollers have a 3-byte signature code that identifies the device. This
code can be read in both Serial and Parallel modes. The three bytes reside in a separate address space, and for the ATmega161 they are:
1. $000: $1E (indicates manufactured by Atmel)
2. $001: $94 (indicates 16 KB Flash memory)
3. $002: $01 (indicates ATmega161 device when $001 is $94)
Programming the Flash
and EEPROM
Atmel’s ATmega161 offers 16K bytes of In-System Reprogrammable Flash Program
memory and 512 bytes of EEPROM Data memory.
The ATmega161 is normally shipped with the On-chip Flash program and EEPROM
Data memory arrays in the erased state (i.e., contents = $FF) and ready to be programmed. This device supports a High-voltage (12V) Parallel Programming mode and a
Low-voltage Serial Programming mode. The +12V is used for programming enable only,
and no current of significance is drawn by this pin. The Serial Programming mode provides a convenient way to download the program and data into the ATmega161 inside
the user’s system.
The Program memory array on the ATmega161 is organized as 128 pages of 128 bytes
each. When programming the Flash, the program data is latched into a page buffer. This
allows one page of program data to be programmed simultaneously in either Programming mode.
The EEPROM Data Memory array on the ATmega161 is programmed byte-by-byte in
either Programming mode. An auto-erase cycle is provided with the self-timed EEPROM
programming operation in the Serial Programming mode.
During programming, the supply voltage must be in accordance with Table 41.
Table 41. Supply Voltage during Programming
Part
Serial Programming
Parallel Programming
ATmega161L
2.7 - 5.5V
4.5 - 5.5V
ATmega161
4.0 - 5.5V
4.5 - 5.5V
117
1228D–AVR–02/07
Parallel Programming
This section describes how to parallel program and verify Flash Program memory,
EEPROM Data memory, Lock bits and Fuse bits in the ATmega161. Pulses are
assumed to be at least 500 ns unless otherwise noted.
Signal Names
In this section, some pins of the ATmega161 are referenced by signal names describing
their functionality during parallel programming (see Figure 75 and Table 42). Pins not
described in the following table are referenced by pin name.
The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a positive pulse. The bit codings are shown in Table 43.
When pulsing WR or OE, the command loaded determines the action executed. The
command is a byte where the different bits are assigned functions as shown in Table 44.
Figure 75. Parallel Programming
ATmega161
+5V
RDY/BSY
PD1
OE
PD2
WR
PD3
BS1
PD4
XA0
PD5
XA1
PD6
PAGEL
PD7
VCC
PB7 - PB0
+12 V
DATA
RESET
PA0
XTAL1
GND
Table 42. Pin Name Mapping
118
Signal Name in
Programming Mode
Pin Name
I/O
Function
RDY/BSY
PD1
O
0: Device is busy programming; 1: Device is ready
for new command
OE
PD2
I
Output Enable (Active low)
WR
PD3
I
Write Pulse (Active low)
BS1
PD4
I
Byte Select 1 (“0” selects Low byte, “1” selects
High byte)
XA0
PD5
I
XTAL Action Bit 0
XA1
PD6
I
XTAL Action Bit 1
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 42. Pin Name Mapping
Signal Name in
Programming Mode
Pin Name
I/O
PAGEL
PD7
I
Program Memory Page Load
BS2
PA0
I
Byte Select 2 (Always low)
DATA
PB7 - 0
I/O
Function
Bi-directional Data Bus (Output when OE is low)
Table 43. XA1 and XA0 Coding
XA1
XA0
Action when XTAL1 is Pulsed
0
0
Load Flash or EEPROM Address (High or low address byte determined by BS1)
0
1
Load Data (High or low data byte for Flash determined by BS1)
1
0
Load Command
1
1
No Action, Idle
Table 44. Command Byte Bit Coding
Command Byte
Enter Programming Mode
Command Executed
1000 0000
Chip Erase
0100 0000
Write Fuse bits
0010 0000
Write Lock bits
0001 0000
Write Flash
0001 0001
Write EEPROM
0000 1000
Read Signature Bytes
0000 0100
Read Fuse and Lock bits
0000 0010
Read Flash
0000 0011
Read EEPROM
The following algorithm puts the device in Parallel Programming mode:
1. Apply 4.5 - 5.5V between VCC and GND.
2. Set RESET and BS pins to “0” and wait at least 500 ns.
3. Apply 11.5 - 12.5V to RESET, and wait for at least 500 ns.
Chip Erase
The Chip Erase will erase the Flash and EEPROM memories plus Lock bits. The Lock
bits are not reset until the Program memory has been completely erased. The Fuse bits
are not changed. A Chip Erase must be performed before the Flash is reprogrammed.
Load Command “Chip Erase”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “1000 0000”. This is the command for Chip Erase.
4. Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low.
5. Wait until RDY/BSY goes high before loading a new command.
119
1228D–AVR–02/07
Programming the Flash
The Flash is organized as 128 pages of 128 bytes each. When programming the Flash,
the program data is latched into a page buffer. This allows one page of program data to
be programmed simultaneously. The following procedure describes how to program the
entire Flash memory:
A. Load Command “Write Flash”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “0001 0000”. This is the command for Write Flash.
4. Give XTAL1 a positive pulse. This loads the command.
B. Load Address Low Byte
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS1 to “0”. This selects low address.
3. Set DATA = Address Low byte ($00 - $FF).
4. Give XTAL1 a positive pulse. This loads the address Low byte.
C. Load Data Low Byte
1. Set BS1 to “0”. This selects low data byte.
2. Set XA1, XA0 to “01”. This enables data loading.
3. Set DATA = Data Low byte ($00 - $FF).
4. Give XTAL1 a positive pulse. This loads the data byte.
D. Latch Data Low Byte
Give PAGEL a positive pulse. This latches the data Low byte.
(See Figure 76 for signal waveforms.)
E. Load Data High Byte
1. Set BS1 to “1”. This selects high data byte.
2. Set XA1, XA0 to “01”. This enables data loading.
3. Set DATA = Data High byte ($00 - $FF).
4. Give XTAL1 a positive pulse. This loads the data byte.
F. Latch Data High Byte
Give PAGEL a positive pulse. This latches the data High byte.
G. Repeat “B” through “F” 64 times to fill the page buffer.
To address a page in the Flash, seven bits are needed (128 pages). The five most significant bits are read from address High byte as described in section “H” below. The two
least significant page address bits, however, are the two most significant bits (bit7 and
bit6) of the latest loaded address Low byte as described in section “B”.
H. Load Address High byte
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS1 to “1”. This selects high address.
3. Set DATA = Address High byte ($00 - $1F).
4. Give XTAL1 a positive pulse. This loads the address High byte.
I. Program Page
120
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
1. Give WR a negative pulse. This starts programming of the entire page of data.
RDY/BSYgoes low.
2. Wait until RDY/BSY goes high.
(See Figure 77 for signal waveforms.)
J. End Page Programming
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set DATA to “0000 0000”. This is the command for No Operation.
3. Give XTAL1 a positive pulse. This loads the command, and the internal write signals are reset.
K. Repeat “A” through “J” 128 times or until all data have been programmed.
Figure 76. Programming the Flash Waveforms
$10
DATA
ADDR. LOW
ADDR. HIGH
DATA LOW
XA1
XA2
BS1
XTAL1
WR
RDY/BSY
RESET +12V
OE
BS2
PAGEL
Figure 77. Programming the Flash Waveforms (Continued)
DATA
DATA HIGH
XA1
XA0
BS1
XTAL1
WR
RDY/BSY
RESET
+12V
OE
PAGEL
BS2
121
1228D–AVR–02/07
Programming the EEPROM
The programming algorithm for the EEPROM Data memory is as follows (refer to “Programming the Flash” for details on command, address and data loading):
1. A: Load Command “0001 0001”.
2. H: Load Address High Byte ($00 - $01)
3. B: Load Address Low Byte ($00 - $FF)
4. E: Load Data Low Byte ($00 - $FF)
L: Write Data Low Byte
1. Set BS to “0”. This selects low data.
2. Give WR a negative pulse. This starts programming of the data byte. RDY/BSY
goes low.
3. Wait until to RDY/BSY goes high before programming the next byte.
(See Figure 78 for signal waveforms.)
The loaded command and address are retained in the device during programming. For
efficient programming, the following should be considered:
•
The command needs to be loaded only once when writing or reading multiple
memory locations.
•
Address High byte only needs to be loaded before programming a new 256-word
page in the EEPROM.
•
Skip writing the data value $FF, that is, the contents of the entire EEPROM after a
Chip Erase.
These considerations also apply to Flash, EEPROM and Signature bytes reading.
Figure 78. Programming the EEPROM Waveforms
DATA
$11
ADDR. HIGH
ADDR. LOW
DATA LOW
XA1
XA2
BS1
XTAL1
WR
RDY/BSY
RESET +12V
OE
BS2
PAGEL
122
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Reading the Flash
The algorithm for reading the Flash memory is as follows (refer to “Programming the
Flash” on page 120 for details on command and address loading):
1. A: Load Command “0000 0010”.
2. H: Load Address High Byte ($00 - $1F)
3. B: Load Address Low Byte ($00 - $FF)
4. Set OE to “0”, and BS1 to “0”. The Flash word Low byte can now be read at
DATA.
5. Set BS to “1”. The Flash word High byte can now be read at DATA.
6. Set OE to “1”.
Reading the EEPROM
The algorithm for reading the EEPROM memory is as follows (refer to “Programming the
Flash” on page 120 for details on command and address loading):
1. A: Load Command “0000 0011”.
2. H: Load Address High Byte ($00 - $01)
3. B: Load Address ($00 - $FF)
4. Set OE to “0”, and BS1 to “0”. The EEPROM Data byte can now be read at
DATA.
5. Set OE to “1”.
Programming the Fuse Bits
The algorithm for programming the Fuse bits is as follows (refer to “Programming the
Flash” on page 120 for details on command and data loading):
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
Bit 6 = BOOTRST Fuse bit
Bit 5 = SPIEN Fuse bit
Bit 4 = SUT Fuse bit
Bit 3 = “1”. This bit is reserved and must be left unprogrammed (“1”).
Bits 2 - 0 = CKSEL2..0 Fuse bits
Bit 7 = “1”. This bit is reserved and should be left unprogrammed (“1”).
3. Give WR a negative pulse and wait for RDY/BSY to go high.
Programming the Lock Bits
The algorithm for programming the Lock bits is as follows (refer to “Programming the
Flash” on page 120 for details on command and data loading):
1. A: Load Command “0010 0000”.
2. D: Load Data Low Byte. Bit n = “0” programs the Lock bit.
Bit 5 = Boot Lock Bit12
Bit 4 = Boot Lock Bit11
Bit 3 = Boot Lock Bit02
Bit 2 = Boot Lock Bit01
Bit 1 = Lock Bit2
Bit 0 = Lock Bit1
Bits 7 - 6 = “1”. These bits are reserved and should be left unprogrammed (“1”).
3. L: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
123
1228D–AVR–02/07
Reading the Fuse and Lock
Bits
The algorithm for reading the Fuse and Lock bits is as follows (refer to “Programming
the Flash” on page 120 for details on command loading):
1. A: Load Command “0000 0100”.
2. Set OE to “0”, and BS to “0”. The status of the Fuse bits can now be read at
DATA (“0” means programmed).
Bit 6 = BOOTRST Fuse bit
Bit 5 = SPIEN Fuse bit
Bit 4 = SUT Fuse bit
Bit 3 = “1”. This bit is reserved and must be left unprogrammed (“1”).
Bits 2 - 0 = CKSEL2..0 Fuse bits
3. Set OE to “0”, and BS to “1”. The status of the Lock bits can now be read at DATA
(“0” means programmed).
Bit 5 = Boot Lock Bit12
Bit 4 = Boot Lock Bit11
Bit 3 = Boot Lock Bit02
Bit 2 = Boot Lock Bit01
Bit 1 = Lock Bit2
Bit 0 = Lock Bit1
4. Set OE to “1”.
Reading the Signature Bytes
The algorithm for reading the Signature bytes is as follows (refer to “Programming the
Flash” on page 120 for details on command and address loading):
1. A: Load Command “0000 1000”.
2. C: Load Address Low Byte ($00 - $02).
Set OE to “0”, and BS to “0”. The selected Signature byte can now be read at DATA.
3. Set OE to “1”.
Parallel Programming
Characteristics
Figure 79. Parallel Programming Timing
tXLWL
tXHXL
XTAL1
tDVXH
tXLDX
Data & Control
(DATA, XA0/1, BS1)
tPLBX t BVWL
tBVXH
PAGEL
tRHBX
tPHPL
Write
tWLWH
WR
tPLWL
WLRL
RDY/BSY
OE
DATA
124
tXLOL
tOLDV
tOHDZ
Read
tWLRH
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 45. Parallel Programming Characteristics, TA = 25°C ± 10%, V CC = 5V ±
10%(1)(2)(3)
Symbol
Parameter
Min
VPP
Programming Enable Voltage
11.5
IPP
Programming Enable Current
tDVXH
Data and Control Valid before XTAL1 High
67
ns
tXHXL
XTAL1 Pulse Width High
67
ns
tXLDX
Data and Control Hold after XTAL1 Low
67
ns
tXLWL
XTAL1 Low to WR Low
67
ns
tBVXH
BS1 Valid before XTAL1 High
67
ns
tPHPL
PAGEL Pulse Width High
67
ns
tPLBX
BS1 Hold after PAGEL Low
67
ns
tPLWL
PAGEL Low to WR Low
67
ns
tBVWL
BS1 Valid to WR Low
67
ns
tRHBX
BS1 Hold after RDY/BSY High
67
ns
tWLWH
WR Pulse Width Low
67
ns
tWLRL
WR Low to RDY/BSY Low
(1)
WR Low to RDY/BSY High
tWLRH
tWLRH_CE
Max
Units
12.5
V
250
µA
0
2.5
µs
1
1.7
ms
(2)
16
28
ms
(3)
8
14
ms
tWLRH_FLASH
WR Low to RDY/BSY High for Write Flash
tXLOL
XTAL1 Low to OE Low
tOLDV
OE Low to DATA Valid
tOHDZ
OE High to DATA Tri-stated
Notes:
Serial Downloading
WR Low to RDY/BSY High for Chip Erase
Typ
67
ns
20
ns
20
ns
1. tWLRH is valid for the Write EEPROM, Write Fuse bits and Write Lock bits commands.
2. tWLRH_CE is valid for the Chip Erase command.
3. tWLRH_FLASH is valid for the Write Flash command.
Both the Flash and EEPROM memory arrays can be programmed using the serial SPI
bus while RESET is pulled to GND. The serial interface consists of pins SCK, MOSI
(input) and MISO (output). After RESET is set low, the Programming Enable instruction
needs to be executed first, before program/erase operations can be executed.
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming operation (in the Serial mode ONLY) and there is no need to first execute the
Chip Erase instruction. The chip erase operation turns the contents of every memory
location in both the program and EEPROM arrays into $FF.
The program and EEPROM memory arrays have separate address spaces:
$0000 to $1FFF for Program memory and $0000 to $01FF for EEPROM memory.
Either an external system clock is supplied at pin XTAL1 or a crystal needs to be connected across pins XTAL1 and XTAL2. The minimum low and high periods for the serial
clock (SCK) input are defined as follows:
Low: > 2 XTAL1 clock cycles
High: > 2 XTAL1 clock cycles
125
1228D–AVR–02/07
Serial Programming
Algorithm
When writing serial data to the ATmega161, data is clocked on the rising edge of SCK.
When reading data from the ATmega161, data is clocked on the falling edge of SCK.
See Figure 80, Figure 81 and Table 49 for timing details.
To program and verify the ATmega161 in the Serial Programming mode, the following
sequence is recommended (see 4-byte instruction formats in Table 48):
1. Power-up sequence:
Apply power between VCC and GND while RESET and SCK are set to “0”. If a crystal is not connected across pins XTAL1 and XTAL2, apply a clock signal to the
XTAL1 pin. In some systems, the programmer cannot guarantee that SCK is held
low during power-up. In this case, RESET must be given a positive pulse of at least
two XTAL1 cycles’ duration after SCK has been set to “0”.
2. Wait for at least 20 ms and enable serial programming by sending the Programming Enable serial instruction to pin MOSI/PB5.
3. The serial programming instructions will not work if the communication is out of
synchronization. When in sync, the second byte ($53) will echo back when issuing the third byte of the Programming Enable instruction. Whether or not the
echo is correct, all four bytes of the instruction must be transmitted. If the $53 did
not echo back, give RESET a positive pulse and issue a new Programming
Enable command.
4. If a chip erase is performed (must be done to erase the Flash), give RESET a
positive pulse and start over from step 2.
5. The Flash is programmed one page at a time. The memory page is loaded one
byte at a time by supplying the 6 LSB of the address and data together with the
Load Program Memory Page instruction. The Program Memory Page is stored
by loading the Write Program Memory Page instruction with the 7 MSB of the
address. If polling is not used, the user must wait at least tWD_FLASH before issuing the next page (please refer to Table 46). Accessing the serial programming
interface before the Flash write operation completes can result in incorrect
programming.
6. The EEPROM array is programmed one byte at a time by supplying the address
and data together with the appropriate Write instruction. An EEPROM memory
location is first automatically erased before new data is written. If polling is not
used, the user must wait at least tWD_EEPROM before issuing the next byte (please
refer to Table 46). In a chip-erased device, no $FFs in the data file(s) need to be
programmed.
7. Any memory location can be verified by using the Read instruction, which
returns the content at the selected address at serial output MISO/PB6.
8. At the end of the programming session, RESET can be set high to commence
normal operation.
9. Power-off sequence (if needed):
Set XTAL1 to “0” (if a crystal is not used).
Set RESET to “1”.
Turn VCC power off.
Data Polling Flash
126
When a page is being programmed into the Flash, reading an address location within
the page being programmed will give the value $FF. At the time the device is ready for a
new page, the programmed value will read correctly. This is used to determine when the
next page can be written. Note that the entire page is written simultaneously and any
address within the page can be used for polling. Data polling of the FLASH will not work
for the value $FF, so when programming this value, the user will have to wait for at least
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
tWD_FLASH before programming the next page. As a chip-erased device contains $FF in
all locations, programming of addresses that are meant to contain $FF can be skipped.
See Table 46 for tWD_FLASH value.
Data Polling EEPROM
When a new byte has been written and is being programmed into EEPROM, reading the
address location being programmed will give the value $FF. At the time the device is
ready for a new byte, the programmed value will read correctly. This is used to determine when the next byte can be written. This will not work for the value $FF, but the user
should keep the following in mind: As a chip-erased device contains $FF in all locations,
programming of addresses that are meant to contain $FF can be skipped. This does not
apply if the EEPROM is reprogrammed without chip-erasing the device. In this case,
data polling cannot be used for the value $FF, and the user will have to wait at least
tWD_EEPROM before programming the next byte. See Table 46 for tWD_EEPROM value.
Table 46. Minimum Wait Delay before Writing the Next Flash or EEPROM Location
Symbol
Minimum Wait Delay
tWD_FLASH
14 ms
tWD_EEPROM
3.4 ms
Table 47. Minimum Wait Delay after a Chip Erase Command
Symbol
Minimum Wait Delay
tWD_ERASE
28 ms
Figure 80. Serial Programming Waveforms
SERIAL DATA INPUT
PB5 (MOSI)
MSB
LSB
SERIAL DATA OUTPUT
PB6 (MISO)
MSB
LSB
SERIAL CLOCK INPUT
PB7(SCK)
SAMPLE
127
1228D–AVR–02/07
.
Table 48. Serial Programming Instruction Set(1)
Instruction Format
Instruction
Byte 1
Byte 2
Byte 3
Byte 4
Programming Enable
1010 1100
0101 0011
xxxx xxxx
xxxx xxxx
Enable Serial Programming after
RESET goes low.
Chip Erase
1010 1100
100x xxxx
xxxx xxxx
xxxx xxxx
Chip Erase EEPROM and Flash.
Read Program Memory
0010 H000
xxxa aaaa
bbbb bbbb
oooo oooo
Read H (high or low) data o from
Program memory at word address
a:b.
Load Program Memory
Page
0100 H000
xxxx xxxx
xxbb bbbb
iiii iiii
Write H (high or low) data i to
Program memory page at word
address b.
Write Program Memory
Page
0100 1100
xxxa aaaa
bbxx xxxx
iiii iiii
Write Program memory page at
address a:b.
Read EEPROM Memory
1010 0000
xxxx xxxa
bbbb bbbb
oooo oooo
Read data o from EEPROM
memory at address a:b.
Write EEPROM Memory
1100 0000
xxxx xxxa
bbbb bbbb
iiii iiii
Write data i to EEPROM memory
at address a:b.
Read Lock bits
0101 1000
xxxx xxxx
xxxx xxxx
xx65 4321
Read Lock bits. “0” = programmed,
“1” = unprogrammed.
Write Lock bits
1010 1100
111x xxxx
xxxx xxxx
1165 4321
Write Lock bits. Set bits 6 - 1 = “0”
to program Lock bits.
Read Signature Byte
0011 0000
xxxx xxxx
xxxx xxbb
oooo oooo
Read Signature byte o at address
b.
Write Fuse bits
1010 1100
101x xxxx
xxxx xxxx
1D1B 1987
Set bits D - B, 9 - 7 = “0” to
program, “1” to unprogram
Read Fuse bits
0101 0000
xxxx xxxx
xxxx xxxx
xDCB 1987
Read Fuse bits. “0” = programmed,
“1” = unprogrammed
Note:
128
Operation
1. a = address high bits
b = address low bits
H = 0 – Low byte, 1 – High Byte
o = data out
i = data in
x = don’t care
1 = lock bit 1
2 = lock bit 2
3 = Boot Lock Bit1
4 = Boot Lock Bit2
5 = Boot Lock Bit11
6 = Boot Lock Bit12
7 = CKSEL0 Fuse
8 = CKSEL1 Fuse
9 = CKSEL2 Fuse
B = SUT Fuse
C = SPIEN Fuse
D = BOOTRST Fuse
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Serial Programming
Characteristics
Figure 81. Serial Programming Timing
MOSI
SCK
tSLSH
tSHOX
tOVSH
tSHSL
MISO
tSLIV
Table 49. Serial Programming Characteristics, TA = -40°C to 85°C, VCC = 2.7 - 5.5V
(unless otherwise noted)
Symbol
Parameter
1/tCLCL
Oscillator Frequency
tCLCL
Oscillator Period
Min
Typ
Max
Units
(VCC = 2.7 - 5.5V)
0
4
MHz
(VCC = 4.0 - 5.5V)
0
8
MHz
(VCC = 2.7 - 5.5V)
250
ns
(VCC = 4.0 - 5.5V)
125
ns
tSHSL
SCK Pulse Width High
2 tCLCL
ns
tSLSH
SCK Pulse Width Low
2 tCLCL
ns
tOVSH
MOSI Setup to SCK High
tCLCL
ns
tSHOX
MOSI Hold after SCK High
2 tCLCL
ns
tSLIV
SCK Low to MISO Valid
10
16
32
ns
129
1228D–AVR–02/07
Electrical Characteristics
Absolute Maximum Ratings*
Operating Temperature.................................. -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin except RESET
with Respect to Ground .............................-1.0V to VCC + 0.5V
Voltage on RESET with Respect to Ground ....-1.0V to +13.0V
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Maximum Operating Voltage ............................................ 6.6V
DC Current per I/O Pin ............................................... 40.0 mA
DC Current VCC and GND Pins ............................... 200.0 mA
130
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
DC Characteristics
TA = -40°C to 85°C, VCC = 2.7V to 5.5V (unless otherwise noted)(1)(2)(3)(4)(5)
Symbol
VIL
Parameter
Condition
Input Low Voltage
(Except XTAL1)
VIL1
Input Low Voltage
(XTAL1)
VIH
Input High Voltage
(Except XTAL1, RESET)
VIH1
VIH2
Input High Voltage
(XTAL1)
Input High Voltage
(RESET)
(3)
Min
Typ
Max
Units
0.3 VCC
(1)
V
0.2 VCC
(1)
V
0.6 VCC(2)
VCC + 0.5
V
0.8 VCC
(2)
VCC + 0.5
V
0.9 VCC
(2)
VCC + 0.5
V
0.6
0.5
V
V
-0.5
-0.5
VOL
Output Low Voltage
(Ports A,B,C,D)
VOH
Output High Voltage(4)
(Ports A,B,C,D)
IOH = -3 mA, VCC = 5V
IOH = -1.5 mA, VCC = 3V
IIL
Input Leakage
Current I/O pin
VCC = 5.5V, pin low
(absolute value)
8.0
µA
IIH
Input Leakage
Current I/O pin
VCC = 5.5V, pin high
(absolute value)
980
nA
RRST
Reset Pull-up Resistor
100
500
kΩ
RI/O
I/O Pin Pull-up Resistor
35
120
kΩ
Active mode, VCC = 3V,
4 MHz
3.0
mA
Idle mode VCC = 3V,
4 MHz
1.2
mA
ICC
Power Supply Current
IOL = 20 mA, VCC = 5V
IOL = 10 mA, VCC = 3V
4.2
2.3
V
V
WDT enabled, VCC = 3V
9
15.0
µA
Power-down mode
WDT disabled, VCC = 3V
<1
2.0
µA
VACIO
Analog Comparator
Input Offset Voltage
VCC = 5V
Vin = VCC/2
40
mV
IACLK
Analog Comparator
Input Leakage Current
VCC = 5V
Vin = VCC/2
50
nA
tACPD
Analog Comparator
Propagation Delay
VCC = 2.7V
VCC = 4.0V
(5)
Notes:
-50
750
500
ns
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V) under steady-state
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 200 mA.
2] The sum of all IOL, for ports B0 - B7, D0 - D7 and XTAL2, should not exceed 100 mA.
3] The sum of all IOL, for ports A0 - A7, ALE, OC1B and C0 - C7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (3 mA at VCC = 5V, 1.5 mA at VCC = 3V) under steady-state
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 200 mA.
2] The sum of all IOH, for ports B0 - B7, D0 - D7 and XTAL2, should not exceed 100 mA.
3] The sum of all IOH, for ports A0 - A7, ALE, OC1B and C0 - C7 should not exceed 100 mA.
131
1228D–AVR–02/07
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum VCC for power-down is 2V.
External Clock Drive
Waveforms
Figure 82. External Clock
VIH1
VIL1
Table 50. External Clock Drive(1)
VCC = 2.7V to 5.5V
Symbol
Parameter
1/tCLCL
Oscillator Frequency
tCLCL
Clock Period
250
125
ns
tCHCX
High Time
100
50
ns
tCLCX
Low Time
100
50
ns
tCLCH
Rise Time
1.6
0.5
µs
tCHCL
Fall Time
1.6
0.5
µs
Notes:
132
VCC = 4.0V to 5.5V
Min
Max
Min
Max
Units
0
4
0
8
MHz
1. See “External Data Memory Timing” for a description of how the duty cycle influences
the timing for the external Data memory.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
External Data Memory Timing
Table 51. External Data Memory Characteristics, 4.0 - 5.5 Volts, No Wait State
8 MHz Oscillator
Symbol
Parameter
0
1/tCLCL
Oscillator Frequency
1
tLHLL
ALE Pulse Width
2
tAVLL
3a
Min
Variable Oscillator
Max
Min
Max
Unit
0.0
8.0
MHz
95
1.0tCLCL-30
ns
Address Valid A to ALE Low
22.5
0.5tCLCL-40(1)
ns
tLLAX_ST
Address Hold After ALE Low,
write access
10
10
ns
3b
tLLAX_LD
Address Hold after ALE Low,
read access
15
15
ns
4
tAVLLC
Address Valid C to ALE Low
22.5
0.5tCLCL-40(1)
ns
5
tAVRL
Address Valid to RD Low
95
1.0tCLCL-30
ns
6
tAVWL
Address Valid to WR Low
95
1.0tCLCL-30
ns
7
tLLWL
ALE Low to WR Low
8
tLLRL
ALE Low to RD Low
9
tDVRH
Data Setup to RD High
10
tRLDV
Read Low to Data Valid
11
tRHDX
Data Hold After RD High
12
tRLRH
RD Pulse Width
13
tDVWL
Data Setup to WR Low
42.5
42.5
145
0.5tCLCL-20(2)
0.5tCLCL+20(2)
ns
145
(2)
(2)
ns
0.5tCLCL-20
60
0.5tCLCL+20
60
ns
65
65
0
0
105
1.0tCLCL-20
27.5
ns
ns
0.5tCLCL-35
(1)
ns
0.5tCLCL-35
(1)
ns
14
tWHDX
Data Hold After WR High
15
tDVWH
Data Valid to WR High
95
1.0tCLCL-30
ns
16
tWLWH
WR Pulse Width
105
1.0tCLCL-20
ns
Notes:
27.5
ns
1. This assumes 50% clock duty cycle. The half period is actually the high time of the external clock, XTAL1.
2. This assumes 50% clock duty cycle. The half period is actually the low time of the external clock, XTAL1.
Table 52. External Data Memory Characteristics, 4.0 - 5.5 Volts, 1 Cycle Wait State
8 MHz Oscillator
Min
Max
Variable Oscillator
Symbol
Parameter
Min
Max
Unit
0
1/tCLCL
Oscillator Frequency
0.0
8.0
MHz
10
tRLDV
Read Low to Data Valid
12
tRLRH
RD Pulse Width
230
2.0tCLCL-20
ns
15
tDVWH
Data Valid to WR High
220
2.0tCLCL-30
ns
16
tWLWH
WR Pulse Width
230
2.0tCLCL-20
ns
185
2.0tCLCL-65
ns
133
1228D–AVR–02/07
Table 53. External Data Memory Characteristics, 4.0 - 5.5 Volts, SRWn1 = 1, SRWn0 = 0
8 MHz Oscillator
Min
Max
Variable Oscillator
Symbol
Parameter
Min
Max
Unit
0
1/tCLCL
Oscillator Frequency
0.0
8.0
MHz
10
tRLDV
Read Low to Data Valid
12
tRLRH
RD Pulse Width
355
3.0tCLCL-20
ns
15
tDVWH
Data Valid to WR High
345
3.0tCLCL-30
ns
16
tWLWH
WR Pulse Width
35
3.0tCLCL-20
ns
310
3.0tCLCL-65
ns
Table 54. External Data Memory Characteristics, 4.0 - 5.5 Volts, SRWn1 = 1, SRWn0 = 1
8 MHz Oscillator
Symbol
Parameter
0
1/tCLCL
Oscillator Frequency
10
tRLDV
Read Low to Data Valid
12
tRLRH
RD Pulse Width
14
tWHDX
Data Hold After WR High
15
tDVWH
16
tWLWH
Min
Max
Variable Oscillator
Min
Max
Unit
0.0
8.0
MHz
310
3.0tCLCL-65
ns
355
3.0tCLCL-20
ns
152.5
1.5tCLCL-35
ns
Data Valid to WR High
345
3.0tCLCL-30
ns
WR Pulse Width
355
3.0tCLCL-20
ns
Table 55. External Data Memory Characteristics, 2.7 - 5.5 Volts, No Wait State
4 MHz Oscillator
Symbol
Parameter
0
1/tCLCL
Oscillator Frequency
1
tLHLL
ALE Pulse Width
195
tCLCL-55
ns
2
tAVLL
Address Valid A to ALE Low
60
0.5tCLCL-65
ns
3a
tLLAX_ST
Address Hold After ALE Low,
write access
10
10
ns
3b
tLLAX_LD
Address Hold after ALE Low,
read access
15
15
ns
4
tAVLLC
Address Valid C to ALE Low
60
0.5tCLCL-65
ns
5
tAVRL
Address Valid to RD Low
200
1.0tCLCL-50
ns
6
tAVWL
Address Valid to WR Low
200
1.0tCLCL-50
ns
7
tLLWL
ALE Low to WR Low
105
145
0.5tCLCL-20
0.5tCLCL+20
ns
8
tLLRL
ALE Low to RD Low
105
145
0.5tCLCL-20
0.5tCLCL+20
ns
9
tDVRH
Data Setup to RD High
95
10
tRLDV
Read Low to Data Valid
11
tRHDX
Data Hold After RD High
134
Min
Max
Variable Oscillator
Min
Max
Unit
0.0
4.0
MHz
95
165
0
ns
165
0
ns
ns
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table 55. External Data Memory Characteristics, 2.7 - 5.5 Volts, No Wait State (Continued)
4 MHz Oscillator
Max
Variable Oscillator
Symbol
Parameter
Min
Min
Max
12
tRLRH
RD Pulse Width
230
1.0tCLCL-20
ns
13
tDVWL
Data Setup to WR Low
70
0.5tCLCL-55
ns
14
tWHDX
Data Hold After WR High
125
0.5tCLCL-0
ns
15
tDVWH
Data Valid to WR High
210
1.0tCLCL-40
ns
WR Pulse Width
230
1.0tCLCL-20
16 tWLWH
Notes: 1. This assumes 50% clock duty cycle. The half period is actually the high time of the external clock, XTAL1.
2. This assumes 50% clock duty cycle. The half period is actually the low time of the external clock, XTAL1.
Unit
ns
Table 56. External Data Memory Characteristics, 2.7 - 5.5 Volts, SRWn1 = 0, SRWn0 = 1
4 MHz Oscillator
Min
Max
Variable Oscillator
Symbol
Parameter
Min
Max
Unit
0
1/tCLCL
Oscillator Frequency
0.0
4.0
MHz
10
tRLDV
Read Low to Data Valid
12
tRLRH
RD Pulse Width
480
2.0tCLCL-20
ns
15
tDVWH
Data Valid to WR High
460
2.0tCLCL-40
ns
16
tWLWH
WR Pulse Width
480
2.0tCLCL-20
ns
335
2.0tCLCL-165
ns
Table 57. External Data Memory Characteristics, 2.7 - 5.5 Volts, SRWn1 = 1, SRWn0 = 0
4 MHz Oscillator
Min
Max
Variable Oscillator
Symbol
Parameter
Min
Max
Unit
0
1/tCLCL
Oscillator Frequency
0.0
4.0
MHz
10
tRLDV
Read Low to Data Valid
12
tRLRH
RD Pulse Width
730
3.0tCLCL-20
ns
15
tDVWH
Data Valid to WR High
710
3.0tCLCL-40
ns
16
tWLWH
WR Pulse Width
730
3.0tCLCL-20
ns
585
3.0tCLCL-165
ns
Table 58. External Data Memory Characteristics, 2.7 - 5.5 Volts, SRWn1 = 1, SRWn0 = 1
4 MHz Oscillator
Min
Max
Variable Oscillator
Symbol
Parameter
Min
Max
Unit
0
1/tCLCL
Oscillator Frequency
0.0
4.0
MHz
10
tRLDV
Read Low to Data Valid
12
tRLRH
RD Pulse Width
730
3.0tCLCL-20
ns
14
tWHDX
Data Hold After WR High
375
1.5tCLCL-0
ns
15
tDVWH
Data Valid to WR High
710
3.0tCLCL-40
ns
16
tWLWH
WR Pulse Width
730
3.0tCLCL-20
ns
585
3.0tCLCL-165
ns
135
1228D–AVR–02/07
Figure 83. External Memory Timing (SRWn1 = 0, SRWn0 = 0)
T1
T2
T4
T3
System Clock Ø
1
ALE
4
Address [15..8]
Prev. addr.
7
XX
Address
15
2
Data/Address [7..0]
Prev. data
3a 13
Address
XX
XX
Data
XX
6
Write
14
16
WR
3b
Prev. data
XX
XX
10
8
Read
Data/Address [7..0]
11
9
Data
Address
5
12
RD
Figure 84. External Memory Timing (SRWn1 = 0, SRWn0 = 1)
T1
T2
T3
T4
T5
System Clock Ø
1
ALE
4
Address [15..8]
Prev. addr.
7
XX
Address
XX
15
2
Data/Address [7..0]
Prev. data
XX
3a 13
Address
Data
XX
6
Write
14
16
WR
Prev. data
XX
9
Data
Address
5
XX
10
8
11
12
Read
3b
Data/Address [7..0]
RD
136
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 85. External Memory Timing (SRWn1 = 1, SRWn0 = 0)
T1
T2
T4
T3
T5
T6
System Clock Ø
1
ALE
4
Address [15..8]
Prev. addr.
7
XX
Address
XX
15
2
Data/Address [7..0]
Prev. data
3a 13
Address
XX
Data
XX
6
Write
14
16
WR
3b
Prev. data
11
9
Data
Address
5
XX
XX
10
8
Read
Data/Address [7..0]
12
RD
Figure 86. External Memory Timing (SRWn1 = 1, SRWn0 = 1)(1)
T1
T2
T3
T4
T6
T5
T7
System Clock Ø
1
ALE
4
Address [15..8]
Prev. addr.
7
XX
Address
XX
15
2
Data/Address [7..0]
Prev. data
XX
3a 13
Address
Data
XX
Write
14
6
16
WR
Prev. data
XX
Address
5
9
10
8
11
XX
Data
12
Read
3b
Data/Address [7..0]
RD
Note:
1. The ALE pulse in the last period (T4 - T7) is only present if the next instruction
accesses the RAM (internal or external). The data and address will only change in T4
- T7 if ALE is present (the next instruction accesses the RAM).
137
1228D–AVR–02/07
Typical
Characteristics
Analog Comparator offset voltage is measured as absolute offset.
Figure 87. Analog Comparator Offset Voltage vs. Common Mode Voltage
ANALOG COMPARATOR OFFSET VOLTAGE vs.
COMMON MODE VOLTAGE VCC = 5V
18
16
TA = 25˚C
OFFSET VOLTAGE (mV)
14
12
TA = 85˚C
10
8
6
4
2
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
COMMON MODE VOLTAGE (V)
Figure 88. Analog Comparator Offset Voltage vs. Common Mode Voltage
ANALOG COMPARATOR OFFSET VOLTAGE vs.
COMMON MODE VOLTAGE VCC = 2.7V
10
TA = 25˚C
OFFSET VOLTAGE (mV)
8
6
TA = 85˚C
4
2
0
0
0.5
1
1.5
2
2.5
3
COMMON MODE VOLTAGE (V)
138
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 89. Analog Comparator Input Leakage Current
ANALOG COMPARATOR INPUT LEAKAGE CURRENT
VCC = 6V TA = 25˚C
60
50
IACLK (nA)
40
30
20
10
0
-10
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
VIN (V)
Figure 90. Watchdog Oscillator Frequency vs. VCC
WATCHDOG OSCILLATOR FREQUENCY vs. VCC
1600
TA = 25˚C
1400
TA = 85˚C
FRC (kHz)
1200
1000
800
600
400
200
0
2
2.5
3
3.5
4
4.5
5
5.5
6
VCC (V)
Sink and source capabilities of I/O ports are measured on one pin at a time.
139
1228D–AVR–02/07
Figure 91. Pull-up Resistor Current vs. Input Voltage
PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
VCC = 5V
120
TA = 25˚C
100
TA = 85˚C
IOP (µA)
80
60
40
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VOP (V)
Figure 92. Pull-up Resistor Current vs. Input Voltage
PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
VCC = 2.7V
30
TA = 25˚C
25
TA = 85˚C
IOP (µA)
20
15
10
5
0
0
0.5
1
1.5
2
2.5
3
VOP (V)
140
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 93. I/O Pin Sink Current vs. Output Voltage
I/O PIN SINK CURRENT vs. OUTPUT VOLTAGE
VCC = 5V
70
TA = 25˚C
60
TA = 85˚C
IOL (mA)
50
40
30
20
10
0
0
0.5
1
1.5
2
2.5
3
VOL (V)
Figure 94. I/O Pin Source Current vs. Output Voltage
I/O PIN SOURCE CURRENT vs. OUTPUT VOLTAGE
VCC = 5V
20
TA = 25˚C
18
16
TA = 85˚C
IOH (mA)
14
12
10
8
6
4
2
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VOH (V)
141
1228D–AVR–02/07
Figure 95. I/O Pin Sink Current vs. Output Voltage
I/O PIN SINK CURRENT vs. OUTPUT VOLTAGE
VCC = 2.7V
25
TA = 25˚C
20
IOL (mA)
TA = 85˚C
15
10
5
0
0
0.5
1
1.5
2
VOL (V)
Figure 96. I/O Pin Source Current vs. Output Voltage
I/O PIN SOURCE CURRENT vs. OUTPUT VOLTAGE
VCC = 2.7V
6
TA = 25˚C
5
TA = 85˚C
IOH (mA)
4
3
2
1
0
0
0.5
1
1.5
2
2.5
3
VOH (V)
142
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Figure 97. I/O Pin Input Threshold vs. VCC
I/O PIN INPUT THRESHOLD VOLTAGE vs. VCC
TA = 25˚C
THRESHOLD VOLTAGE (V)
2.5
2
1.5
1
0.5
0
2.7
4.0
5.0
VCC
Figure 98. I/O Pin Input Hysteresis vs. VCC
I/O PIN INPUT HYSTERESIS vs. VCC
TA = 25˚C
0.18
0.16
IINPUT HYSTERESIS (V)
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
2.7
4.0
5.0
VCC
143
1228D–AVR–02/07
Register Summary
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
$3F ($5F)
SREG
I
T
H
S
V
N
Z
C
page 21
$3E ($5E)
SPH
SP15
SP14
SP13
SP12
SP11
SP10
SP9
SP8
page 22
$3D ($5D)
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
page 22
$3C ($5C)
SPL
Reserved
$3B ($5B)
GIMSK
INT1
INT0
INT2
-
-
-
-
-
page 30
$3A ($5A)
GIFR
INTF1
INTF0
INTF2
$39 ($59)
TIMSK
TOIE1
OCIE1A
OCIE1B
TOIE2
TICIE1
OCIE2
TOIE0
OCIE0
page 31
$38 ($58)
TIFR
TOV1
OCF1A
OCF1B
TOV2
ICF1
OCFI2
TOV0
OCIF0
page 33
page 31
$37 ($57)
SPMCR
-
-
-
-
LBSET
PGWRT
PGERS
SPMEN
page 114
$36 ($56)
EMCUCR
SM0
SRL2
SRL1
SRL0
SRW01
SRW00
SRW11
ISC2
page 36
$35 ($55)
MCUCR
SRE
SRW10
SE
SM1
ISC11
ISC10
ISC01
ISC00
page 34
$34 ($54)
MCUSR
-
-
-
-
WDRF
BORF
EXTRF
PORF
page 29
$33 ($53)
TCCR0
FOC0
PWM0
COM01
COM00
CTC0
CS02
CS01
CS00
page 42
$32 ($52)
TCNT0
Timer/Counter0 Counter Register
$31 ($51)
OCR0
Timer/Counter0 Output Compare Register
$30 ($50)
SFIOR
-
-
-
-
-
-
PSR2
PSR10
page 39
page 44
page 44
$2F ($4F)
TCCR1A
COM1A1
COM1A0
COM1B1
COM1B0
FOC1A
FOC1B
PWM11
PWM10
page 50
$2E ($4E)
TCCR1B
ICNC1
ICES1
-
-
CTC1
CS12
CS11
CS10
page 52
$2D ($4D)
TCNT1H
Timer/Counter1 - Counter Register High Byte
page 53
$2C ($4C)
TCNT1L
Timer/Counter1 - Counter Register Low Byte
page 53
$2B ($4B)
OCR1AH
Timer/Counter1 - Output Compare Register A High Byte
page 54
$2A ($4A)
OCR1AL
Timer/Counter1 - Output Compare Register A Low Byte
page 54
$29 ($49)
OCR1BH
Timer/Counter1 - Output Compare Register B High Byte
page 54
$28 ($48)
OCR1BL
$27 ($47)
TCCR2
FOC2
PWM2
COM21
COM20
CTC2
CS22
CS21
CS20
page 42
$26 ($46)
ASSR
-
-
-
-
AS20
TCON2UB
OCR2UB
TCR2UB
page 47
$25 ($45)
ICR1H
Timer/Counter1 - Input Capture Register High Byte
$24 ($44)
ICR1L
Timer/Counter1 - Input Capture Register Low Byte
page 54
$23 ($43)
TCNT2
Timer/Counter2 Counter Register
page 44
$22 ($42)
OCR2
$21 ($41)
WDTCR
$20 ($40)
UBRRHI
Timer/Counter1 - Output Compare Register B Low Byte
page 54
page 54
Timer/Counter2 Output Compare Register
-
-
-
WDTOE
WDE
page 44
WDP2
UBRR1[11:8]
-
-
WDP1
WDP0
UBRR0[11:8]
-
-
-
-
page 58
page 78
$1F ($3F)
EEARH
$1E ($3E)
EEARL
-
EEAR8
$1D ($3D)
EEDR
$1C ($3C)
EECR
-
-
-
-
EERIE
EEMWE
EEWE
EERE
page 61
$1B ($3B)
PORTA
PORTA7
PORTA6
PORTA5
PORTA4
PORTA3
PORTA2
PORTA1
PORTA0
page 89
$1A ($3A)
DDRA
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
page 89
$19 ($39)
PINA
PINA7
PINA6
PINA5
PINA4
PINA3
PINA2
PINA1
PINA0
page 89
$18 ($38)
PORTB
PORTB7
PORTB6
PORTB5
PORTB4
PORTB3
PORTB2
PORTB1
PORTB0
page 91
$17 ($37)
DDRB
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
page 91
$16 ($36)
PINB
PINB7
PINB6
PINB5
PINB4
PINB3
PINB2
PINB1
PINB0
page 91
$15 ($35)
PORTC
PORTC7
PORTC6
PORTC5
PORTC4
PORTC3
PORTC2
PORTC1
PORTC0
page 98
$14 ($34)
DDRC
DDC7
DDC6
DDC5
DDC4
DDC3
DDC2
DDC1
DDC0
page 98
$13 ($33)
PINC
PINC7
PINC6
PINC5
PINC4
PINC3
PINC2
PINC1
PINC0
page 98
$12 ($32)
PORTD
PORTD7
PORTD6
PORTD5
PORTD4
PORTD3
PORTD2
PORTD1
PORTD0
page 100
$11 ($31)
DDRD
DDD7
DDD6
DDD5
DDD4
DDD3
DDD2
DDD1
DDD0
page 100
$10 ($30)
PIND
PIND7
PIND6
PIND5
PIND4
PIND3
PIND2
PIND1
PIND0
page 100
EEPROM Address Register Low Byte
page 60
page 60
EEPROM Data Register
page 60
$0F ($2F)
SPDR
$0E ($2E)
SPSR
SPIF
WCOL
-
-
SPI Data Register
-
-
-
SPI2X
page 67
page 68
$0D ($2D)
SPCR
SPIE
SPE
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
page 66
$0C ($2C)
UDR0
$0B ($2B)
UCSR0A
RXC0
TXC0
UDRE0
FE0
OR0
-
U2X0
MPCM0
page 73
$0A ($2A)
UCSR0B
RXCIE0
TXCIE0
UDRIE0
RXEN0
TXEN0
CHR90
RXB80
TXB80
page 75
$09 ($29)
UBRR0
$08 ($28)
ACSR
ACD
AINBG
ACO
ACI
ACIE
ACIC
ACIS1
ACIS0
page 81
$07 ($27)
PORTE
-
-
-
-
-
PORTE2
PORTE1
PORTE0
page 106
$06 ($26)
DDRE
-
-
-
-
-
DDE2
DDE1
DDE0
page 106
$05 ($25)
PINE
-
-
-
-
-
PINE2
PINE1
PINE0
page 106
$04 ($24)
Reserved
UART0 I/O Data Register
page 73
UART0 Baud Rate Register
page 78
$03 ($23)
UDR1
$02 ($22)
UCSR1A
RXC1
TXC1
UDRE1
FE1
OR1
-
U2X1
MPCM1
page 75
$01 ($21)
UCSR1B
RXCIE1
TXCIE1
UDRIE1
RXEN1
TXEN1
CHR91
RXB81
TXB81
page 73
$00 ($20)
UBRR1
144
UART1 I/O Data Register
UART1 Baud Rate Register
page 73
page 78
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Notes:
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
should never be written.
2. Some of the Status Flags are cleared by writing a logical “1” to them. Note that the CBI and SBI instructions will operate on
all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions
work with registers $00 to $1F only.
145
1228D–AVR–02/07
Instruction Set Summary
Mnemonic
Operands
Description
Operation
Flags
# Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD
Rd, Rr
Add Two Registers
Rd ← Rd + Rr
Z,C,N,V,H
ADC
Rd, Rr
Add with Carry Two Registers
Rd ← Rd + Rr + C
Z,C,N,V,H
1
ADIW
Rdl, K
Add Immediate to Word
Rdh:Rdl ← Rdh:Rdl + K
Z,C,N,V,S
2
SUB
Rd, Rr
Subtract Two Registers
Rd ← Rd - Rr
Z,C,N,V,H
1
SUBI
Rd, K
Subtract Constant from Register
Rd ← Rd - K
Z,C,N,V,H
1
SBC
Rd, Rr
Subtract with Carry Two Registers
Rd ← Rd - Rr - C
Z,C,N,V,H
1
SBCI
Rd, K
Subtract with Carry Constant from Reg.
Rd ← Rd - K - C
Z,C,N,V,H
1
SBIW
Rdl, K
Subtract Immediate from Word
Rdh:Rdl ← Rdh:Rdl - K
Z,C,N,V,S
2
AND
Rd, Rr
Logical AND Registers
Rd ← Rd • Rr
Z,N,V
1
ANDI
Rd, K
Logical AND Register and Constant
Rd ← Rd • K
Z,N,V
1
OR
Rd, Rr
Logical OR Registers
Rd ← Rd v Rr
Z,N,V
1
1
ORI
Rd, K
Logical OR Register and Constant
Rd ← Rd v K
Z,N,V
1
EOR
Rd, Rr
Exclusive OR Registers
Rd ← Rd ⊕ Rr
Z,N,V
1
COM
Rd
One’s Complement
Rd ← $FF - Rd
Z,C,N,V
1
NEG
Rd
Two’s Complement
Rd ← $00 - Rd
Z,C,N,V,H
1
SBR
Rd, K
Set Bit(s) in Register
Rd ← Rd v K
Z,N,V
1
CBR
Rd, K
Clear Bit(s) in Register
Rd ← Rd • ($FF - K)
Z,N,V
1
INC
Rd
Increment
Rd ← Rd + 1
Z,N,V
1
DEC
Rd
Decrement
Rd ← Rd - 1
Z,N,V
1
TST
Rd
Test for Zero or Minus
Rd ← Rd • Rd
Z,N,V
1
CLR
Rd
Clear Register
Rd ← Rd ⊕ Rd
Z,N,V
1
SER
Rd
Set Register
Rd ← $FF
None
1
MUL
Rd, Rr
Multiply Unsigned
R1:R0 ← Rd x Rr
Z,C
2
MULS
Rd, Rr
Multiply Signed
R1:R0 ← Rd x Rr
Z,C
2
MULSU
Rd, Rr
Multiply Signed with Unsigned
R1:R0 ← Rd x Rr
Z,C
2
FMUL
Rd, Rr
Fractional Multiply Unsigned
R1:R0 ← (Rd x Rr) << 1
Z,C
2
FMULS
Rd, Rr
Fractional Multiply Signed
R1:R0 ← (Rd x Rr) << 1
Z,C
2
FMULSU
Rd, Rr
Fractional Multiply Signed with Unsigned
R1:R0 ← (Rd x Rr) << 1
Z,C
2
2
BRANCH INSTRUCTIONS
RJMP
k
IJMP
Relative Jump
PC ← PC + k + 1
None
Indirect Jump to (Z)
PC ← Z
None
2
JMP
k
Direct Jump
PC ← k
None
3
RCALL
k
Relative Subroutine Call
PC ← PC + k + 1
None
3
Indirect Call to (Z)
PC ← Z
None
3
Direct Subroutine Call
PC ← k
None
4
RET
Subroutine Return
PC ← STACK
None
4
RETI
Interrupt Return
PC ← STACK
I
4
ICALL
CALL
k
CPSE
Rd, Rr
Compare, Skip if Equal
if (Rd = Rr) PC ← PC + 2 or 3
None
CP
Rd, Rr
Compare
Rd - Rr
Z,N,V,C,H
1
CPC
Rd, Rr
Compare with Carry
Rd - Rr - C
Z,N,V,C,H
1
CPI
Rd, K
Compare Register with Immediate
Rd - K
Z,N,V,C,H
SBRC
Rr, b
Skip if Bit in Register Cleared
if (Rr(b) = 0) PC ← PC + 2 or 3
None
1/2/3
1
1/2/3
SBRS
Rr, b
Skip if Bit in Register is Set
if (Rr(b) = 1) PC ← PC + 2 or 3
None
1/2/3
SBIC
P, b
Skip if Bit in I/O Register Cleared
if (P(b) = 0) PC ← PC + 2 or 3
None
1/2/3
SBIS
P, b
Skip if Bit in I/O Register is Set
if (P(b) = 1) PC ← PC + 2 or 3
None
1/2/3
BRBS
s, k
Branch if Status Flag Set
if (SREG(s) = 1) then PC ← PC + k + 1
None
1/2
BRBC
s, k
Branch if Status Flag Cleared
if (SREG(s) = 0) then PC ← PC + k + 1
None
1/2
BREQ
k
Branch if Equal
if (Z = 1) then PC ← PC + k + 1
None
1/2
BRNE
k
Branch if Not Equal
if (Z = 0) then PC ← PC + k + 1
None
1/2
BRCS
k
Branch if Carry Set
if (C = 1) then PC ← PC + k + 1
None
1/2
BRCC
k
Branch if Carry Cleared
if (C = 0) then PC ← PC + k + 1
None
1/2
BRSH
k
Branch if Same or Higher
if (C = 0) then PC ← PC + k + 1
None
1/2
BRLO
k
Branch if Lower
if (C = 1) then PC ← PC + k + 1
None
1/2
BRMI
k
Branch if Minus
if (N = 1) then PC ← PC + k + 1
None
1/2
BRPL
k
Branch if Plus
if (N = 0) then PC ← PC + k + 1
None
1/2
BRGE
k
Branch if Greater or Equal, Signed
if (N ⊕ V = 0) then PC ← PC + k + 1
None
1/2
BRLT
k
Branch if Less than Zero, Signed
if (N ⊕ V = 1) then PC ← PC + k + 1
None
1/2
BRHS
k
Branch if Half-carry Flag Set
if (H = 1) then PC ← PC + k + 1
None
1/2
BRHC
k
Branch if Half-carry Flag Cleared
if (H = 0) then PC ← PC + k + 1
None
1/2
146
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Instruction Set Summary (Continued)
Mnemonic
Operands
Description
Operation
Flags
BRTS
k
Branch if T-flag Set
if (T = 1) then PC ← PC + k + 1
None
# Clocks
BRTC
k
Branch if T-flag Cleared
if (T = 0) then PC ← PC + k + 1
None
1/2
BRVS
k
Branch if Overflow Flag is Set
if (V = 1) then PC ← PC + k + 1
None
1/2
BRVC
k
Branch if Overflow Flag is Cleared
if (V = 0) then PC ← PC + k + 1
None
1/2
BRIE
k
Branch if Interrupt Enabled
if (I = 1) then PC ← PC + k + 1
None
1/2
BRID
k
Branch if Interrupt Disabled
if (I = 0) then PC ← PC + k + 1
None
1/2
Rd ← Rr
Rd+1:Rd ← Rr+1:Rr
None
1
None
1
1
1/2
DATA TRANSFER INSTRUCTIONS
MOV
Rd, Rr
Move between Registers
MOVW
Rd, Rr
Copy Register Word
LDI
Rd, K
Load Immediate
Rd ← K
None
LD
Rd, X
Load Indirect
Rd ← (X)
None
2
LD
Rd, X+
Load Indirect and Post-inc.
Rd ← (X), X ← X + 1
None
2
LD
Rd, -X
Load Indirect and Pre-dec.
X ← X - 1, Rd ← (X)
None
2
LD
Rd, Y
Load Indirect
Rd ← (Y)
None
2
LD
Rd, Y+
Load Indirect and Post-inc.
Rd ← (Y), Y ← Y + 1
None
2
LD
Rd, -Y
Load Indirect and Pre-dec.
Y ← Y - 1, Rd ← (Y)
None
2
LDD
Rd, Y+q
Load Indirect with Displacement
Rd ← (Y + q)
None
2
LD
Rd, Z
Load Indirect
Rd ← (Z)
None
2
LD
Rd, Z+
Load Indirect and Post-inc.
Rd ← (Z), Z ← Z + 1
None
2
LD
Rd, -Z
Load Indirect and Pre-dec.
Z ← Z - 1, Rd ← (Z)
None
2
LDD
Rd, Z+q
Load Indirect with Displacement
Rd ← (Z + q)
None
2
LDS
Rd, k
Load Direct from SRAM
Rd ← (k)
None
2
ST
X, Rr
Store Indirect
(X) ← Rr
None
2
ST
X+, Rr
Store Indirect and Post-inc.
(X) ← Rr, X ← X + 1
None
2
ST
-X, Rr
Store Indirect and Pre-dec.
X ← X - 1, (X) ← Rr
None
2
ST
Y, Rr
Store Indirect
(Y) ← Rr
None
2
ST
Y+, Rr
Store Indirect and Post-inc.
(Y) ← Rr, Y ← Y + 1
None
2
ST
-Y, Rr
Store Indirect and Pre-dec.
Y ← Y - 1, (Y) ← Rr
None
2
STD
Y+q, Rr
Store Indirect with Displacement
(Y + q) ← Rr
None
2
ST
Z, Rr
Store Indirect
(Z) ← Rr
None
2
ST
Z+, Rr
Store Indirect and Post-inc.
(Z) ← Rr, Z ← Z + 1
None
2
ST
-Z, Rr
Store Indirect and Pre-dec.
Z ← Z - 1, (Z) ← Rr
None
2
STD
Z+q, Rr
Store Indirect with Displacement
(Z + q) ← Rr
None
2
STS
k, Rr
Store Direct to SRAM
(k) ← Rr
None
2
Load Program Memory
R0 ← (Z)
None
3
LPM
LPM
Rd, Z
Load Program Memory
Rd ← (Z)
None
3
LPM
Rd, Z+
Load Program Memory and Post-inc.
Rd ← (Z), Z ← Z + 1
None
3
Store Program Memory
(Z) ← R1:R0
None
-
IN
Rd, P
In Port
Rd ← P
None
1
OUT
P, Rr
Out Port
P ← Rr
None
1
PUSH
Rr
Push Register on Stack
STACK ← Rr
None
2
POP
Rd
Pop Register from Stack
Rd ← STACK
None
2
SPM
BIT AND BIT-TEST INSTRUCTIONS
SBI
P, b
Set Bit in I/O Register
I/O(P,b) ← 1
None
2
CBI
P, b
Clear Bit in I/O Register
I/O(P,b) ← 0
None
2
LSL
Rd
Logical Shift Left
Rd(n+1) ← Rd(n), Rd(0) ← 0
Z,C,N,V
1
LSR
Rd
Logical Shift Right
Rd(n) ← Rd(n+1), Rd(7) ← 0
Z,C,N,V
1
ROL
Rd
Rotate Left through Carry
Rd(0) ← C, Rd(n+1) ← Rd(n), C ← Rd(7)
Z,C,N,V
1
ROR
Rd
Rotate Right through Carry
Rd(7) ← C, Rd(n) ← Rd(n+1), C ← Rd(0)
Z,C,N,V
1
ASR
Rd
Arithmetic Shift Right
Rd(n) ← Rd(n+1), n = 0..6
Z,C,N,V
1
1
SWAP
Rd
Swap Nibbles
Rd(3..0) ← Rd(7..4), Rd(7..4) ← Rd(3..0)
None
BSET
s
Flag Set
SREG(s) ← 1
SREG(s)
1
BCLR
s
Flag Clear
SREG(s) ← 0
SREG(s)
1
BST
Rr, b
Bit Store from Register to T
T ← Rr(b)
T
1
BLD
Rd, b
Bit Load from T to Register
Rd(b) ← T
None
1
SEC
Set Carry
C←1
C
1
CLC
Clear Carry
C←0
C
1
SEN
Set Negative Flag
N←1
N
1
CLN
Clear Negative Flag
N←0
N
1
147
1228D–AVR–02/07
Instruction Set Summary (Continued)
Mnemonic
Description
Operation
Flags
SEZ
Set Zero Flag
Z←1
Z
1
CLZ
Clear Zero Flag
Z←0
Z
1
SEI
Global Interrupt Enable
I←1
I
1
CLI
Global Interrupt Disable
I←0
I
1
SES
Set Signed Test Flag
S←1
S
1
CLS
Clear Signed Test Flag
S←0
S
1
SEV
Set Two’s Complement Overflow
V←1
V
1
CLV
Clear Two’s Complement Overflow
V←0
V
1
SET
Set T in SREG
T←1
T
1
CLT
Clear T in SREG
T←0
T
1
SEH
Set Half-carry Flag in SREG
H←1
H
1
CLH
Clear Half-carry Flag in SREG
H←0
H
1
NOP
No Operation
None
1
SLEEP
Sleep
(see specific descr. for Sleep function)
None
3
WDR
Watchdog Reset
(see specific descr. for WDR/timer)
None
1
148
Operands
# Clocks
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Ordering Information
Speed (MHz)
Power Supply
4
2.7 - 5.5V
8
Note:
4.0 - 5.5V
Ordering Code
Package
Operation Range
ATmega161-4AC
ATmega161-4PC
44A
40P6
Commercial
(0°C to 70°C)
ATmega161-4AI
ATmega161-4PI
44A
40P6
Industrial
(-40°C to 85°C)
ATmega161-8AC
ATmega161-8PC
44A
40P6
Commercial
(0°C to 70°C)
ATmega161-8AI
ATmega161-8PI
44A
40P6
Industrial
(-40°C to 85°C)
This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and
minimum quantities.
Package Type
44A
44-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
40P6
40-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP)
149
1228D–AVR–02/07
Packaging Information
44A
PIN 1
B
PIN 1 IDENTIFIER
E1
e
E
D1
D
C
0˚~7˚
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
10/5/2001
R
150
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
DRAWING NO. REV.
44A
B
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
40P6
PIN 1
B
PIN 1 IDENTIFIER
E1
e
E
D1
D
C
0˚~7˚
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
10/5/2001
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
DRAWING NO. REV.
44A
B
151
1228D–AVR–02/07
Errata
ATmega161 Rev. E
•
•
•
•
•
PWM not Phase Correct
Increased Interrupt Latency
Interrupt Return Fails when Stack Pointer Addresses the External Memory
Writing UBBRH Affects both UART0 and UART1
Store Program Memory Instruction May Fail
5. PWM not Phase Correct
In phase correct PWM mode, a change from OCRx = TOP to anything less than
TOP does not change the OCx output. This gives a phase error in the following
period.
Problem Fix/Workaround
Make sure this issue is not harmful to the application.
4. Increased Interrupt Latency
In this device, some instructions are not interruptable, and will cause the interrupt
latency to increase. The only practical problem concerns a loop followed by a twoword instruction while waiting for an interrupt. The loop may consist of a branch
instruction or an absolute or relative jump back to itself like this:
loop: rjmp loop
<Two-word instruction>
In this case, a dead-lock situation arises.
Problem Fix/Workaround
In assembly, insert a nop instruction immediately after a loop to itself. The problem
will normally be detected during development. In C, the only construct that will give
this problem is an empty “for” loop; “for(;;)”. Use “while(1)” or “do{} while (1)” to avoid
the problem.
3. Interrupt Return Fails when Stack Pointer Addresses the External Memory
When Stack Pointer addresses external memory (SPH:SPL > $45F), returning from
interrupt will fail. The program counter will be updated with a wrong value and thus
the program flow will be corrupted.
Problem Fix/Workaround
Address the stack pointer to internal SRAM or disable interrupts while Stack Pointer
addresses external memory.
2. Writing UBBRH Affects Both UART0 and UART1
Writing UBRRHI updates baud rate generator for both UART0 and UART1. The
baud rate generator's counter is updated each time either UBRR or UBRRHI are
written. Since the UBRRHI regiSter is shared by UART0 and UART1, changing the
baud rate for one UART will affect the operation of the other UART.
Problem Fix/Workaround
Do not update UBRRHI for one UART when transmitting/receiving data on the
other.
152
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
1. Store Program Memory Instruction May Fail
At certain frequencies and voltages, the store program memory (SPM) instruction
may fail.
Problem Fix/Workaround
Avoid using the SPM instruction.
153
1228D–AVR–02/07
Data Sheet Change
Log for ATmega161
This document contains a log on the changes made to the data sheet for ATmega161.
Changes from Rev.
1228C-08/02 to Rev.
1228D-02/07
1
Package Drawing updated from rev. A to rev. B.
2
Written “Not recommend in new designs” on features page.
Changes from Rev.
1228B-09/01 to Rev.
1228C-08/02
All page numbers refers to this document.
154
1
Description of Brown-out Detector (BOD) removed from data sheet.
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
Table of Contents
Features................................................................................................. 1
Disclaimer.............................................................................................. 1
Pin Configuration.................................................................................. 2
Description ............................................................................................ 3
Block Diagram ...................................................................................................... 4
Pin Descriptions.................................................................................................... 5
Crystal Oscillator................................................................................................... 6
Architectural Overview......................................................................... 7
The General Purpose Register File ....................................................................
ALU – Arithmetic Logic Unit................................................................................
Self-programmable Flash Program Memory.......................................................
EEPROM Data Memory......................................................................................
SRAM Data Memory...........................................................................................
Program and Data Addressing Modes................................................................
Memory Access Times and Instruction Execution Timing ..................................
l/O Memory .........................................................................................................
Reset and Interrupt Handling..............................................................................
MCU Control Register – MCUCR .......................................................................
Sleep Modes.......................................................................................................
10
11
11
11
12
13
17
19
22
34
36
Timer/Counters ................................................................................... 38
Timer/Counter Prescalers................................................................................... 38
8-bit Timer/Counters T/C0 and T/C2 .................................................................. 40
Timer/Counter1................................................................................................... 49
Watchdog Timer.................................................................................. 58
EEPROM Read/Write Access............................................................. 60
Prevent EEPROM Corruption ............................................................................. 62
Serial Peripheral Interface – SPI........................................................ 63
SS Pin Functionality............................................................................................ 65
Data Modes ........................................................................................................ 65
UARTs.................................................................................................. 69
Data Transmission..............................................................................................
Data Reception ...................................................................................................
UART Control .....................................................................................................
Baud Rate Generator..........................................................................................
Double-speed Transmission ...............................................................................
69
71
73
76
78
Analog Comparator ............................................................................ 81
i
1228D–AVR–02/07
Internal Voltage Reference ................................................................ 83
Voltage Reference Enable Signals and Start-up Time ....................................... 83
Interface to External Memory ............................................................ 84
Using the External Memory Interface ................................................................. 88
I/O Ports............................................................................................... 89
Port A.................................................................................................................. 89
Port B.................................................................................................................. 91
Port B Schematics .............................................................................................. 94
Port C.................................................................................................................. 98
Port D................................................................................................................ 100
Port E................................................................................................................ 106
Memory Programming...................................................................... 110
Boot Loader Support.........................................................................................
Entering the Boot Loader Program ...................................................................
Capabilities of the Boot Loader.........................................................................
Self-programming the Flash .............................................................................
110
111
112
112
Program Memory Lock bits ............................................................. 116
Fuse bits ...........................................................................................................
Signature Bytes ................................................................................................
Programming the Flash and EEPROM.............................................................
Parallel Programming .......................................................................................
Parallel Programming Characteristics ..............................................................
Serial Downloading...........................................................................................
Serial Programming Characteristics .................................................................
116
117
117
118
124
125
129
Electrical Characteristics................................................................. 130
Absolute Maximum Ratings*............................................................................. 130
DC Characteristics............................................................................ 131
External Clock Drive Waveforms ...................................................................... 132
External Data Memory Timing .......................................................................... 133
Typical Characteristics .................................................................... 138
Register Summary ............................................................................ 144
Instruction Set Summary ................................................................. 146
Ordering Information........................................................................ 149
Packaging Information ..................................................................... 150
44A ................................................................................................................... 150
ii
ATmega161(L)
1228D–AVR–02/07
ATmega161(L)
40P6 ................................................................................................................. 151
Errata ................................................................................................. 152
ATmega161 Rev. E .......................................................................................... 152
Data Sheet Change Log for ATmega161 ........................................ 154
Changes from Rev. 1228B-09/01 to Rev. 1228C-08/02 ................................... 154
Table of Contents .................................................................................. i
iii
1228D–AVR–02/07
iv
ATmega161(L)
1228D–AVR–02/07
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. ATMEL ®, logo and combinations thereof, Everywhere You Are ®, AVR ®, AVR Studio ®, and others, are®registered® trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of othATMEL and AVR are the registered trademarks of Atmel.
ers.
Other terms and product names may be the trademarks of others.
1228D–AVR–02/07