AT25M02 - Complete

AT25M02
SPI Serial EEPROM
2-Mbit (262,144 x 8)
DATASHEET
Features

Low-voltage and Standard-voltage Operation Available
̶
̶
1.7V (VCC = 1.7V to 5.5V)
2.5V (VCC = 2.5V to 5.5V)

Serial Peripheral Interface (SPI) Compatible Interface
Supports SPI Modes 0 (0,0) and 3 (1,1)

High Speed Operation

256-byte Page Write Mode Support

̶
̶
5MHz Clock Rate from 1.7V to 5.5V
Partial Page Writes Allowed
Byte Write Operation Supported
̶

Self-timed Write Cycle
̶

All Write Operations Complete Within 10ms Max
Block Write Protection
̶

Ability to Protect the Upper Quarter, Upper Half, or the Entire Memory Array
Multiple Write Protection Methods
̶

Write Protect (WP) Pin and Write Disable instructions for Both Hardware and
Software Data Protection
High Reliability
̶
Endurance: 1,000,000 Write Cycles
Data Retention: 40 Years
̶

Green Package Options (Lead-free/Halide-free/RoHS Compliant)
̶

8-lead JEDEC SOIC and 8-ball Thin WLCSP
Die Sale Options
̶
Wafer form, Waffle Pack, and Bumped Die Available
Description
The Atmel® AT25M02 provides 2,097,152 bits of Serial Electrically Erasable
Programmable Read-Only Memory (EEPROM) organized as 262,144 words of
8 bits each. The device is optimized for use in many industrial and commercial
applications where low-power and low-voltage operation is essential. The device
is available in space saving 8-lead JEDEC SOIC and 8-ball Thin WLCSP
packages. In addition, the device operates from 1.7V to 5.5V.
The AT25M02 is enabled through the Chip Select pin (CS) and accessed via a
3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and
Serial Clock (SCK). All programming cycles are completely self-timed and a
separate erase cycle is not required before writing to the device.
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
T a b l e o f C o n te n ts
1.
Pin Configurations and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.
Device Block Diagram and Bus Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.
Device Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1
3.2
3.3
3.4
4.
Interfacing the AT25M02 on the SPI Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Opcodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hold Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
6
6
Device Commands and Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1
4.2
4.3
4.4
Status Register Bit Definition and Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Read Status Register (RDSR) and Low Power Write Poll (LPWP). . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.1
Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.2
Low Power Write Poll (LPWP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Write Enable (WREN) and Write Disable (WRDI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.1
Write Enable Instruction (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.2
Write Disable Instruction (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4.1
Block Write Protect Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4.2
Write Protect Enable Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.
Read Array Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.
Write Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1
6.2
7.
Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1
Internal Writing Methodology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2
Polling Routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
14
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC and AC Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Cell Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Up Requirements, Reset, and Default Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.1
Device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.2
Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.3
Device Default State at Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7.4
Device Default Condition from Atmel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
17
18
18
18
18
19
19
19
8.
Ordering Code Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
10. Part Marking Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11. Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11.1
11.2
8S1 — 8-lead JEDEC SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8U-10 — 8-ball WLCSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
12. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
1.
Pin Configurations and Pinouts
Table 1-1.
Pin Description
Pin
Pin
Number Symbol Pin Name and Functional Description
1
2
CS
SO
Chip Select: Asserting the CS pin selects the device. When the CS pin is
deasserted, the device will be deselected and placed in standby mode and the
SO pin will be in a high impedance state. When the device is deselected, data
will not be accepted on the SI pin.
A high-to-low transition on the CS pin is required to start an operation and a
low-to-high transition is required to end an operation. When ending the
internally self-timed write cycle, the device will not enter the standby mode until
the completion of the operation.
Serial Data Output: The SO pin is used to shift data out from the device. Data
on the SO pin is always clocked out on the falling edge of SCK. The SO pin will
be in a high impedance state whenever the device is deselected (CS is
deasserted).
Write Protect: The Write Protect (WP) pin is used in conjunction with the block
protection bits of the Status Register (see Table 4-3 on page 10) to inhibit
writing to a portion of, or the entire memory array.
Asserted
State
Pin
Type
Low
Input
—
Output
Low
Input
3
WP
4
GND
Ground: The ground reference for the device power supply (VCC). GND should
be connected to the system ground.
—
Power
5
SI
Serial Data Input: Instructions, addresses and data are latched by the
AT25M02 on the rising edge of the Serial Clock (SCK) line via the Serial Data
Input (SI) pin.
—
Input
SCK
Serial Clock: The Serial Clock (SCK) pin is used to provide a clock to the
device and is used to synchronize the flow of data to and from the device.
Instructions, addresses and data present on SI pin are always latched in on the
rising edge of SCK, while output data on the SO pin is always clocked out on
the falling edge of SCK.
—
Input
7
HOLD
Hold: When the device is selected and a serial sequence is underway, Hold can
be used to pause the serial communication with the master device without
resetting the serial sequence. To pause, the HOLD pin must be brought low
while the SCK pin is low. To resume serial communication, the HOLD pin is
brought high while the SCK pin is low (SCK may still toggle during Hold). Inputs
to the SI pin will be ignored and the SO pin will be in a high impedance state.
Low
Input
8
VCC
Device Power Supply: The VCC pin is used to supply the source voltage to the
device. Operations at invalid VCC voltages may produce spurious results and
should not be attempted.
—
Power
6
The WP pin can also be used in conjunction with the WPEN bit to prevent
inadvertent writing to the Status Register (see Table 4-4 on page 11). The
protection is invoked by driving the WP pin to a low state.
8-lead SOIC
CS
1
8
8-ball WLCSP
VCC
SO
2
7
HOLD
WP
3
6
SCK
GND
4
5
SI
Top View
VCC
8
HOLD
7
SCK
SI
6
5
CS
1
2
SO
3
WP
4
Top View
GND
Note: Drawings are not to scale.
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
3
2.
Device Block Diagram and Bus Connections
Figure 2-1.
Block Diagram
Memory
System Control
Module
CS
High Voltage
Generation Circuit
Power
On Reset
Generator
VCC
Suspend
Operation
Control
HOLD
Status Register
EEPROM Array
SO
Row Decoder
(256 bytes per page x 1024 pages)
Full Array WP Range
1 page
Half Array WP Range
Address Register
and Counter
Quarter Array WP Range
Column Decoder
WP
SCK
Data Register
Data Output
Buffer
Write
Protection
Control
GND
Figure 2-2.
SI
SPI Bus Master Connections to Serial EEPROMs
SPI Master:
Microcontroller
Serial Clock (SPI CK)
Data Out (MISO)
Data In (MOSI)
SI
SS3 SS2 SS1 SS0
4
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
SO SCK
SI
SO SCK
SI
SO SCK
SI
SO SCK
Slave 0
AT25xxx
Slave 1
AT25xxx
Slave 2
AT25xxx
Slave 3
AT25xxx
CS
CS
CS
CS
3.
Device Operation
The AT25M02 is controlled by a set of instructions that are sent from a host controller, commonly referred to as
the SPI Master. The SPI Master communicates with the AT25M02 via the SPI bus which is comprised of four
signal lines: Chip Select (CS), Serial Clock (SCK), Serial Input (SI), and Serial Output (SO).
The SPI protocol defines a total of four modes of operation (mode 0, 1, 2, or 3) with each mode differing in
respect to the SCK polarity and phase and how the polarity and phase control the flow of data on the SPI bus.
The AT25M02 supports the two most common modes, SPI Modes 0 and 3. With SPI Modes 0 and 3, data is
always latched in on the rising edge of SCK and always output on the falling edge of SCK. The only difference
between SPI Modes 0 and 3 is the polarity of the SCK signal when in the inactive state (when the SPI Master is
in standby mode and not transferring any data). SPI Mode 0 is defined as a low SCK while CS is not asserted
(at VCC) and SPI Mode 3 has SCK high in the inactive state. The SCK idle state must match when the CS is
deasserted both before and after the communication sequence in SPI Mode 0 and 3. The figures in this
document depict Mode 0 with a solid line on SCK while CS is inactive and Mode 3 with a dotted line.
Figure 3-1.
SPI Mode 0 and Mode 3
CS
Mode 3
Mode 3
Mode 0
Mode 0
SCK
SI
MSB
SO
3.1
LSB
MSB
LSB
Interfacing the AT25M02 on the SPI Bus
Communication to and from the AT25M02 must be initiated by the SPI Master device, such as a microcontroller.
The SPI Master device must generate the serial clock for the AT25M02 on the SCK pin. The AT25M02 always
operates as a slave due to the fact that the Serial Clock pin (SCK) is always an input.
Selecting the Device: The AT25M02 is selected when the CS pin is low. When the device is not selected, data
will not be accepted via the SI pin, and the SO pin will remain in a high impedance state.
Sending Data to the Device: The AT25M02 uses the Serial Data Input (SI) pin to receive information. All
instructions, addresses and data input bytes are clocked into the device with the Most Significant Bit (MSB) first.
The SI pin samples on the first rising edge of the SCK line after the CS has been asserted.
Receiving Data from the Device: Data output from the device is transmitted on the Serial Data Output (SO)
pin, with the MSB output first. The SO data is latched on the first falling edge of SCK after the instruction has
been clocked into the device, such as the Read from Memory Array and Read Status Register instructions. See
Section 5. “Read Array Operation” on page 12 for more details.
3.2
Device Opcodes
Serial Opcode: After the device is selected by driving CS low, the first byte will be received on the SI pin. This
byte contains the opcode that defines the operation to be performed. Please refer to Table 4-1 on page 7 for a
list of all opcodes that the AT25M02 will respond to.
Invalid Opcode: If an invalid opcode is received, no data will be shifted into AT25M02 and the Serial Data
Output (SO) pin will remain in a high impedance state until the falling edge of CS is detected again. This will
reinitialize the serial communication.
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
5
3.3
Hold Function
The HOLD pin is used to pause the serial communication with the device without having to stop or reset the
clock sequence. The Hold mode, however, does not have an effect on the internal write cycle. Therefore, if a
write cycle is in progress, asserting the HOLD pin will not pause the operation and the write cycle will continue to
completion.
The Hold mode can only be entered while the CS pin is asserted. The Hold mode is activated by asserting the
HOLD pin during the SCK low pulse. If the HOLD pin is asserted during the SCK high pulse, then the Hold mode
will not be started until the beginning of the next SCK low pulse. The device will remain in the Hold mode as long
as the HOLD pin and CS pin are asserted.
While in Hold mode, the SO pin will be in a high impedance state. In addition, both the SI pin and the SCK pin
will be ignored. The WP pin, however, can still be asserted or deasserted while in the Hold mode.
To end the Hold mode and resume serial communication, the HOLD pin must be deasserted during the SCK low
pulse. If the HOLD pin is deasserted during the SCK high pulse, then the Hold mode will not end until the
beginning of the next SCK low pulse.
If the CS pin is deasserted while the HOLD pin is still asserted, then any operation that may have been started
will be aborted and the device will reset the WEL bit in the Status Register back to the Logic 0 state.
Figure 3-2.
Hold Mode
CS
SCK
HOLD
Hold
Figure 3-3.
Hold
Hold
Hold Timing
CS
tCD
tCD
SCK
tHD
tHD
HOLD
tHZ
tLZ
SO
3.4
Write Protection
The Write Protect (WP) pin will allow normal read/write operations when held high. When the WP pin is brought
low and WPEN bit is a Logic 1, all write operations to the Status Register are inhibited. The WP pin going low
while CS is still low will interrupt a Write to the Status Register. If the internal write cycle has already been
initiated, WP going low will have no effect on any write operation to the Status Register. The WP pin function is
blocked when the WPEN bit in the Status Register is a Logic 0. This will allow the user to install the AT25M02
device in a system with the WP pin tied to ground and still be able to write to the Status Register. All WP pin
functions are enabled when the WPEN bit is set to a Logic 1.
6
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
4.
Device Commands and Addressing
The AT25M02 is designed to interface directly with the synchronous Serial Peripheral Interface (SPI) of the
6800 type series of microcontrollers.
The AT25M02 utilizes an 8-bit instruction register. The list of instructions and their operation codes are
contained in Table 4-1. All instructions, addresses, and data are transferred with the MSB first and start with a
high-to-low CS transition.
Table 4-1.
Instruction Set For the Atmel AT25M02
Instruction
Name
Instruction
Format
RDSR
0000 0101 (05h)
Read Status Register (SR)
Status Register
Section 4.2.1
LPWP
0000 1000 (08h)
Low Power Write Poll
Status Register
Section 4.2.2
WREN
0000 0110 (06h)
Set Write Enable Latch (WEL)
Status Register
Section 4.3.1
WRDI
0000 0100 (04h)
Reset Write Enable Latch (WEL)
Status Register
Section 4.3.2
WRSR
0000 0001 (01h)
Write Status Register (SR)
Status Register
Section 4.4
READ
0000 0011 (03h)
Read from Memory Array
Memory Array
Section 5.
Write to Memory Array
Memory Array
Section 6.
0000 0010 (02h)
WRITE
4.1
0000 0111 (07h)
Operation Description
Operates On
Refer to Section
Status Register Bit Definition and Function
The AT25M02 includes an 8-bit Status Register. The Status Register bits modulate various features of the
device as shown in Table 4-2. These bits can be changed by specific instructions that are detailed in the
following sections.
Table 4-2.
Status Register Bit Definition
Bit
Name
7
WPEN
6:4
RFU
3:2
BP1
BP0
Write Protect Enable
Reserved for Future Use
Block Write Protection
Type
R/W
R
R/W
1
WEL
Write Enable Latch
R/W
0
RDY/BSY
Ready/Busy Status
R
Description
0
See Table 4-4 (Factory Default).
1
See Table 4-4.
0
Reads as zeros when the device is not in a write cycle.
1
Reads as ones when the device is in a write cycle.
00
No array write protection (Factory Default)
01
Quarter memory array protection (see Table 4-3).
10
Half memory array protection (see Table 4-3).
11
Entire memory array protection (see Table 4-3).
0
Device is not write enabled (Power-up Default).
1
Device is write enabled.
0
Device is ready for a new sequence.
1
Device is busy with an internal operation.
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
7
4.2
Read Status Register (RDSR) and Low Power Write Poll (LPWP)
4.2.1
Read Status Register (RDSR)
The Read Status Register instruction provides access to the Status Register. The ready/busy and write enable
status of the device can be determined by the RDSR instruction. Similarly, the Block Write Protection bits
indicate the extent of memory array protection employed. The Status Register is read by asserting the CS pin,
followed by sending in a 05h opcode on the SI pin. Upon completion of the opcode, the device will return the
8-bit Status Register value on the SO pin.
Figure 4-1.
RDSR Waveform
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
RDSR Opcode (05h)
SI
0
0
0
0
0
1
0
1
MSB
Status Register Data Out
High Impedance
SO
D7
D6
D5
D4
D3
D2
D1
D0
MSB
The Status Register can be continuously read for data by continuing to read beyond the first 8-bit value
returned. The AT25M02 will update the Status Register value upon the completion of every 8 bits, thereby
allowing new Status Register values to be read without having to issue a new RDSR instruction.
4.2.2
Low Power Write Poll (LPWP)
The Low Power Write Poll command can be used after any write command as a means to check if the device
has completed its internal write cycle. The LPWP command requires an opcode of 08h and will return an FFh
value when the part is still busy completing the write cycle. The LPWP command will return a 00h value if the
part is no longer in a write cycle. Refer to section Section 6.2.1 on page 14 for a description on implementing a
polling routine. Continuous reading of the LPWP state is supported and the value output by the device will be
updated every eight bits.
Figure 4-2.
LPWP Timing
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
LPWP Opcode (08h)
SI
0
0
0
0
1
0
0
0
MSB
FFh or 00h Data Out
High Impedance
SO
D7
MSB
8
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
D6
D5
D4
D3
D2
D1
D0
4.3
Write Enable (WREN) and Write Disable (WRDI)
Enabling and disabling writing to the Status Register and EEPROM array is accomplished through the Write
Enable Instruction (WREN) and the Write Disable Instruction (WRDI). These functions change the status of the
WEL bit in the Status Register.
4.3.1
Write Enable Instruction (WREN)
The Write Enable Latch (WEL) bit of the Status Register must be set to a Logic 1 prior to each WRSR and
WRITE instruction. This is accomplished by sending a WREN (06h) command to the AT25M02. First, the CS pin
is driven low to select the device and then a 06h instruction value is clocked in on the SI pin. Then the CS pin
can be driven high and the WEL bit will be updated in the Status Register to a Logic 1. The device will power-up
in the write disable state (WEL = 0).
Figure 4-3.
WREN Timing
CS
0
1
2
3
4
5
6
7
SCK
WREN Opcode (06h)
SI
0
0
0
0
0
1
1
0
MSB
High Impedance
SO
4.3.2
Write Disable Instruction (WRDI)
To protect the device against inadvertent writes, the Write Disable instruction (opcode 04h) disables all
programming modes by setting the WEL bit to a Logic 0. The WRDI instruction is independent of the status of
the WP pin.
Figure 4-4.
WRDI Timing
CS
0
1
2
3
4
5
6
7
SCK
WRDI Opcode (04h)
SI
0
0
0
0
0
1
0
0
MSB
High Impedance
SO
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
9
4.4
Write Status Register (WRSR)
The Write Status Register (WRSR) instruction enables the SPI Master to change selected bits of the Status
Register. Before a WRSR sequence can be initiated, a WREN instruction must be executed to set the WEL to
Logic 1. Upon completion of a WREN sequence, a WRSR sequence can be executed.
Note:
The WRSR function has no effect on bit 6, bit 5, bit 4, bit 1 and bit 0 of the Status Register. Only bit 7, bit 3 and
bit 2 can be changed via the WRSR sequence. These modifiable bits are the Write Protect Enable (WPEN) bit
and Block Protect (BP1, BP0) bits. These three bits are non-volatile cells that have the same properties and
functions as regular EEPROM cells. Their values are retained while power is removed from the device.
The AT25M02 will not respond to commands other than a RDSR after a WRSR sequence until the self-timed
internal write cycle has completed. When the write cycle is completed, the WEL bit in the Status Register is
reset to Logic 0.
4.4.1
Block Write Protect Function
The WRSR instruction allows the user to select one of four possible combinations as to how the memory array
will be inhibited from writing through changing the Block Write Protect bits (BP1, BP0). The four levels of array
protection are:




None of the memory array is protected.
Upper quarter (¼) address range is write protected meaning the highest order 512-Kbits are read-only.
Upper half (½) address range is write protected meaning the highest order 1-Mbits are read-only.
All of the memory array is write protected meaning all addresses are read-only.
The Block Write Protection levels and corresponding Status Register control bits are shown in Table 4-3.
Table 4-3.
Block Write Protect Bits
Status Register Bits <3:2>
10
Level
BP1
BP0
Writeable Address Range
Write Protected / Read-Only
Address Range
0
0
0
00000h – 3FFFFh
None
1 (¼)
0
1
00000h – 2FFFFh
30000h – 3FFFFh
2 (½)
1
0
00000h – 1FFFFh
20000h – 3FFFFh
3 (All)
1
1
None
00000h – 3FFFFh
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
4.4.2
Write Protect Enable Function
The WRSR instruction also allows the user to enable or disable the Write Protect (WP) pin through the use of
the Write Protect Enable (WPEN) bit. When the WPEN bit is set to Logic 0, the writability of the EEPROM array
is dictated by the values of the Block Write Protect bits. The writability of the Status Register is controlled by the
WEL bit. When the WPEN bit is set to Logic 1, the Status Register is read-only.
Hardware Write Protection is enabled when both the WP pin is at GND and the WPEN bit has been set to one.
When the device is Hardware Write Protected, all writing to the Status Register, including the Block Write
Protection bits, the WEL and the WPEN bit, and to the sections in the memory array selected by the Block Write
Protection bits are disabled. When Hardware Write Protection is enabled, writes are only allowed to sections of
the memory that are not block protected.
Hardware Write Protection is disabled when either the WP pin is at VCC or the WPEN bit is zero. When
Hardware Write Protection is disabled, writes are only allowed to sections of the memory that are not block
protected.
Note:
When the WPEN bit is hardware write protected, it cannot be changed back to zero, as long as the WP
pin is held at GND.
Table 4-4.
WPEN Operation
WPEN
WP Pin
WEL
Protected Blocks
Unprotected Blocks
Status Register
0
X
0
Protected
Protected
Protected
0
X
1
Protected
Writable
Writable
1
GND
0
Protected
Protected
Protected
1
GND
1
Protected
Writable
Protected
X
VCC
0
Protected
Protected
Protected
X
VCC
1
Protected
Writable
Writable
Figure 4-5.
WRSR Waveform
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
Status Register Data In
WRSR Opcode (01h)
SI
0
MSB
0
0
0
0
0
0
1
D7
X
X
X
D3
D2
X
X
MSB
High Impedance
SO
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
11
5.
Read Array Operation
Reading the AT25M02 via the SO pin requires the following sequence. After the CS line is pulled low to select a
device, the Read opcode 03h is transmitted via the SI line followed by the 24-bit address to be read.
Note:
Address bits A23 through A18 are don't care bits as they do not fall within the 2-Mbit addressable range.
Upon completion of the 24-bit address, any data on the SI line will be ignored. The data (D7 – D0) at the
specified address is then shifted out onto the SO line. If only one byte is to be read, the CS line should be driven
high after the data comes out. The Read sequence can be continued since the byte address is automatically
incremented and data will continue to be shifted out. When the highest address is reached (3FFFFh), the
address counter will roll over to the lowest address (00000h) allowing the entire memory to be read in one
continuous read cycle regardless of the starting address.
Figure 5-1.
Read Array
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40 41
SCK
Opcode
SI
0
0
0
0
0
Address Bits A23-A0
0
MSB
1
1
A
A
A
A
A
A
A
A
A
MSB
Data Byte 1
SO
High-impedance
D
MSB
12
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
D
D
D
D
D
D
D
D
MSB
D
6.
Write Commands
In order to program the AT25M02, two separate instructions must be executed. First, the device must be write
enabled via the Write Enable instruction (WREN). Then, one of the two possible Write instructions described in
Section 6.1 may be executed. The address of the memory location(s) to be programmed must be outside the
protected address field location selected by the block write protection level. During an internal write cycle, all
commands will be ignored except the RDSR instruction.
Note:
6.1
If the device is not Write Enabled (WREN), the device will ignore the Write instruction and will return to
the standby state when CS is brought high. A new CS assertion is required to re-initiate communication.
Byte Write
A Byte Write instruction requires the following sequence and is depicted in Figure 6-1. After the CS line is pulled
low to select the device, the Write opcode (02h) is transmitted via the SI line followed by the 24-bit address and
the data (D7 – D0) to be programmed. Programming will start after the CS pin is brought high. The low-to-high
transition of the CS pin must occur during the SCK low time (Mode 0) and SCK high time (Mode 3) immediately
after clocking in the D0 (LSB) data bit. The AT25M02 is automatically returned to the Write Disable state (Status
Register bit WEL = 0) at the completion of a write cycle.
Figure 6-1.
Byte Write
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39
SCK
Opcode
SI
0
0
0
0
Address Bits A23-A0
0
0
1
SO
6.2
A
0
MSB
A
A
A
A
A
Data In
A
A
A D7 D6 D5 D4 D3 D2 D1 D0
MSB
MSB
High-impedance
Page Write
A Page Write sequence allows up to 256 bytes to be written in the same write cycle, provided that all bytes are
in the same row of the memory array (where addresses A17 through A8 are the same). Partial Page Writes of
less than 256 bytes are allowed. After each byte of data is received, the eight lowest order address bits are
internally incremented by one and the remaining address bits will remain constant. If more bytes of data are
transmitted that what will fit to the end of that memory row, the address counter will “roll over” to the beginning of
the same row. Due to the Internal Writing Methodology utilized in the device (see Section 6.2.1), creating a roll
over event should be avoided as data in the page could become unintentionally altered during the write cycle.
The AT25M02 is automatically returned to the Write Disable state (WEL = 0) at the completion of a write cycle.
Figure 6-2.
Page Write
CS
0
1
2
3
4
5
6
7
8
9
29 30 31 32 33 34 35 36 37 38 39
SCK
Opcode
SI
0
0
0
0
0
MSB
SO
Address Bits A23-A0
0
1
0
A
MSB
A
A
A
A
Data In Byte 1
A
D
MSB
D
D
D
D
D
Data In Byte n
D
D
D
D
D
D
D
D
D
D
MSB
High-impedance
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
13
6.2.1
Internal Writing Methodology
The AT25M02 incorporates a built in error detection and correction (EDC) logic scheme. The EEPROM array is
internally organized as a group of four connected 8-bit bytes plus an additional six ECC (Error Correction Code)
bits of EEPROM. These 38 bits are referred to as the internal physical data word. During a read sequence, the
EDC logic compares each 4-byte physical data word with its corresponding six ECC bits. If a single bit out of the
4-byte region happens to read incorrectly, the EDC logic will detect the bad bit and replace it with a correct value
before the data is serially clocked out. This architecture significantly improves the reliability of the AT25M02
compared to an implementation that does not utilize EDC.
It is important to note that data is always physically written to the part at the internal physical data word level,
regardless of the number of bytes written. Writing single bytes is still possible with the Byte Write operation, but
internally, the other three bytes within the 4-byte location where the single byte was written, along with the six
ECC bits will be updated. Due to this architecture, the AT25M02 EEPROM write endurance is rated at the
internal physical data word level (4-byte word). The system designer needs to optimize the application writing
algorithms to observe these internal word boundaries in order to reach the 1,000,000 cycle endurance rating.
6.2.2
Polling Routine
An polling routine can be implemented to optimize time sensitive applications that would not prefer to wait the
fixed maximum write cycle time (tWC). This method allows the application to know immediately when the Serial
EEPROM write cycle has completed to start a subsequent operation.
Once the internally timed write cycle has started, a polling routine can be initiated. This involves repeatedly
sending Read Status Register (RDSR) command to determine if the device has completed its self timed internal
write cycle. If the RDY/BSY bit (Bit 0) = 1, the write cycle is still in progress. If Bit 0 = 0, the write cycle has
ended. If the RDY/BSY bit = 1, repeated RDSR commands can be executed until the RDY/BSY bit = 0, signaling
that the device is ready to execute a new instruction. Only the Read Status Register instruction is enabled
during the write programming cycle.
Figure 6-3.
Polling Flow Chart
Send Valid
Write
Protocol
Deassert
CS to VCC to
Initiate a
Write Cycle
Send RDSR
Instruction
to the Device
Does
RDY/BSY
= 0?
NO
14
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
YES
Continue to
Next Operation
7.
Electrical Specifications
7.1
Absolute Maximum Ratings*
Temperature under Bias. . . . . . . . -55C to +125C
Storage Temperature . . . . . . . . . . -65C to +150C
Supply Voltage
with respect to ground . . . . . . . . . . -0.5V to +6.25V
Voltage on any pin
with respect to ground . . . . . . . . . . . -1.0V to +7.0V
DC Output Current . . . . . . . . . . . . . . . . . . . . 5.0mA
7.2
Functional operation at the “Absolute Maximum Ratings” or any
other conditions beyond those indicated in Section 7-1 is not
implied or guaranteed. Stresses beyond those listed under
“Absolute Maximum Ratings” and/or exposure to the “Absolute
Maximum Ratings” for extended periods may affect device
reliability and cause permanent damage to the device.
The voltage extremes referenced in the “Absolute Maximum
Ratings” are intended to accommodate short duration
undershoot/overshoot pulses that the device may be subjected to
during the course of normal operation and does not imply or
guarantee functional device operation at these levels for any
extended period of time.
DC and AC Operating Range
Table 7-1.
DC and AC Operating Range
AT25M02
Operating Temperature (Case)
VCC Power Supply
Industrial High Temperature
-40C to +85C
Low Voltage Grade
1.7V to 5.5V
Standard Voltage Grade
2.5V to 5.5V
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
15
7.3
DC Characteristics
Table 7-2.
DC Characteristics
Parameter are applicable over operating range in Section 7-1, unless otherwise noted.
Symbol
Parameter
VCC1
Supply Voltage
VCC2
Supply Voltage
Test Condition
Min
Max
Units
1.7
5.5
V
2.5
5.5
V
(2)
Supply Current
(Read)
ICC1
VCC = 1.8V , SCK = 1MHz, SO = Open
0.3
1.0
mA
VCC = 1.8V(2), SCK = 5MHz, SO = Open
0.5
1.0
mA
VCC = 5.0V, SCK = 1MHz, SO = Open
1.0
2.0
mA
VCC = 5.0V, SCK = 5MHz, SO = Open
2.0
3.0
mA
VCC = 1.8V , SO = Open
During tWC, CS = VCC
0.3
2.0
mA
VCC = 5.0V, SO = Open
During tWC, CS = VCC
0.5
3.0
mA
VCC = 1.8V(2), CS = VCC
0.08
1.0
μA
VCC = 2.5V, CS = VCC
0.08
2.0
μA
VCC = 5.5V, CS = VCC
0.15
3.0
μA
(2)
Supply Current
(Write)
ICC2
ISB
IIL
Input Leakage
VIN = 0V to VCC
–3.0
3.0
μA
IOL
Output Leakage
VIN = 0V to VCC, TAC = 0C to 70C
–3.0
3.0
μA
VIL(2)
Input Low-voltage
–1.0
VCC x 0.3
V
VIH(2)
Input High-voltage
VCC x 0.7
VCC + 0.5
V
VOL1
Output Low-voltage
0.4
V
VOH1
Output High-voltage
VOL2
Output Low-voltage
VOH2
Output High-voltage
Notes:
16
Standby Current
Typical(1)
1.
2.
3.6  VCC  5.5V
1.8V  VCC  3.6V
IOL = 3.0mA
IOH = 1.6mA
VCC –0.8
IOL = 0.15mA
IOH = 100μA
0.2
VCC –0.2
Typical values characterized at TA = +25°C unless otherwise noted.
This parameter is characterized but is not 100% tested in production.
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
V
V
V
7.4
AC Characteristics
Table 7-3.
AC Characteristics
Applicable over recommended operating range: TAI= -40C to +85C, CL=1 TTL Gate and 30pF (unless otherwise noted).
VCC = 1.7V to 5.5V
Symbol
Parameter
Min
Max
Units
fSCK
SCK Clock Frequency
0
5
MHz
tRI
Input Rise Time
—
80
ns
tFI(1)
Input Fall Time
—
80
ns
tWH
SCK High Time
80
—
ns
tWL
SCK Low Time
80
—
ns
tCS
CS High Time
200
—
ns
tCSS
CS Setup Time
200
—
ns
tCSH
CS Hold Time
200
—
ns
tSU
Data In Setup Time
20
—
ns
tH
Data In Hold Time
20
—
ns
tHD
Hold Setup Time
20
—
ns
tCD
Hold Hold Time
20
—
ns
tV
Output Valid
0
80
ns
tHO
Output Hold Time
0
—
ns
tLZ
Hold to Output Valid
—
100
ns
tHZ
Hold to Output High Z
—
100
ns
tDIS
Output Disable Time
—
100
ns
tWC
Write Cycle Time
—
10
ms
(1)
Note:
1.
Figure 7-1.
This parameter is ensured by characterization only.
Synchronous Data Timing
tCS
VIH
CS
VIL
tCSS
tCSH
VIH
tWH
SCK
tWL
VIL
tSU
tH
VIH
SI
Valid Data In
VIL
tV
VOH
SO
VOL
High
Impedance
tHO
tDIS
High
Impedance
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
17
7.5
Pin Capacitance
Pin Capacitance(1)
Table 7-4.
Applicable over recommended operating range from TA = 25C, f = 1.0MHz, VCC = 5.0V (unless otherwise noted).
Symbol
Test Conditions
COUT
CIN
Note:
7.6
1.
Max
Units
Conditions
Output Capacitance (SO)
8
pF
VOUT = 0V
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
VIN = 0V
Min
Max
Units
1,000,000
—
Write Cycles
100
—
Years
This parameter is characterized and is not 100% tested.
EEPROM Cell Performance Characteristics
Table 7-5.
EEPROM Cell Performance Characteristics
Operation
Test Condition
Write Endurance(1)
Data Retention(3)
Notes:
1.
2.
3.
7.7
TA = 25°C, VCC(min)< VCC < VCC(max)
Byte(2) or Page Write Mode
TA = 55°C, VCC(min)< VCC < VCC(max)
Write endurance performance is determined through characterization and the qualification process.
Due to the memory array architecture, the Write Cycle Endurance is specified for writes in groups of four data
bytes. The beginning of any 4-byte boundaries can be determined by multiplying any integer (N) by four (i.e
4*N). The end address can be found by adding three to the beginning value (i.e. 4*N+3). See Section 6.2.1
“Internal Writing Methodology” on page 14 for more details on this implementation.
The data retention capability is determined through qualification and is checked on each device in production.
Power-Up Requirements, Reset, and Default Conditions
During a power-up sequence, the VCC supplied to the AT25M02 should monotonically rise from GND to the
minimum VCC level as specified in Section 7-1 on page 15, with a slew rate no greater than of 1V/μs.
7.7.1
Device Reset
To prevent inadvertent write operations or other spurious events from happening during a power-up sequence,
the AT25M02 includes a power-on-reset (POR) circuit. Upon power-up, the device will not respond to any
commands until the VCC level crosses the internal voltage threshold (VPOR) that brings the device out of reset
and into standby mode.
The system designer must ensure that no instruction is sent to the device until the VCC supply has reached a
stable value greater than the minimum VCC level. Once the VCC has surpassed the minimum level, the SPI
Master must wait at least tVCSL before asserting the CS pin. See Table 7-6 for the values associated with these
power-up parameters.
18
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
Table 7-6.
Power-up Conditions(1)
Symbol
Parameter
Min
tVCSL
Minimum VCC to Chip Select Low Time
100
VPOR
Power-On Reset Threshold Voltage
tPOFF
Minimum time at VCC = 0V between power cycles
Note:
1.
Max
Units
μs
1.5
1
V
ms
These parameters are characterized but are not 100% tested in production.
If an event occurs in the system where the VCC level supplied to the AT25M02 drops below the maximum VPOR
level specified, it is recommended that a full power cycle sequence be performed by first driving the VCC pin to
GND, waiting at least the minimum tPOFF time, and then performing a new power-up sequence in compliance
with the requirements defined in this section.
7.7.2
Software Reset
The SPI interface of the AT25M02 can be reset by toggling the CS input. If the CS line is already in the active
state, it must a complete transition from the inactive state (≥ VIH)to the active state (≤ VIL), and then back to the
inactive state (≥ VIH) without sending clocks on the SCK line. Upon completion of this sequence, the device will
be ready to receive a new opcode on the SI line.
7.7.3
Device Default State at Power-up
The AT25M02 default state upon power-up consists of:






7.7.4
Standby Power mode.
Write Enable Latch (WEL) bit in the Status Register = 0.
Ready/Busy bit in the Status Register = 0, indicating the device is ready to accept a new command.
Device is not selected.
Not in Hold condition.
WPEN, BP1 and BP0 bits in the Status Register are unchanged from their previous state due to the fact
that they are non-volatile values.
Device Default Condition from Atmel
The AT25M02 is shipped from Atmel to the customer with the EEPROM array set to an all FFh data pattern
(Logic 1 state). The Write Protection Enable bit in the Status Register is set to Logic 0 (the ability of the
EEPROM array to write is dictated by the values of the Block Write Protect bits while the SR ability to write is
controlled by the WEL bit). The Block Write Protection bits in the Status Register are set to Logic 0 (no write
protection selected).
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
19
8.
Ordering Code Detail
AT2 5 M 0 2 - S S H M x x - T
Atmel Designator
Shipping Carrier Option
T = Tape and Reel
B = Bulk (Tubes)
Product Family
Product Variation /
Customer Specific Option
25 = SPI Serial EEPROM
xx = Applies to selecte packages only.
See ordering table for details.
Device Density
M = Megabit Family
02 = 2 Megabit
Operating Voltage
M = 1.7V to 5.5V
D = 2.5V to 5.5V
Package Device Grade or
Wafer/Die Thickness
U = Green, SnAgCu WLCSP Ball
Industrial Temperature Range
(-40°C to +85°C)
H = Green, NiPdAu Lead Finish
Industrial Temperature Range
(-40°C to +85°C)
11 = 11mil wafer thickness
Package Option
SS = JEDEC SOIC
U1 = 8-ball, 4x4 Grid Array, WLCSP
WWU = Wafer Unsawn
9.
Ordering Information
Additional package types that are not listed below may be available for order. Please contact Atmel for availability details.
Delivery Information
Atmel Ordering Code
Lead Finish
Package
AT25M02-SSHM-T
1.7V to 5.5V
AT25M02-SSHM-B
NiPdAu
AT25M02-SSHD-T
(Lead-free/Halogen-free)
8S1
2.5V to 5.5V
AT25M02-SSHD-B
AT25M02-U1UM0B-T(1)
SnAgCu
(Lead-free/Halogen-free)
AT25M02-WWU11M(2)
Notes:
Voltage
n/a
8U-10
1.7V to 5.5V
Wafer Sale
Quantity
Tape and Reel
4,000 per Reel
Bulk (Tubes)
100 per Tube
Tape and Reel
4,000 per Reel
Bulk (Tubes)
100 per Tube
Tape and Reel
5,000 per Reel
Operation
Range
Industrial
Temperature
(-40C to 85C)
Note 2
1. WLCSP Package:

This device includes a backside coating to increase product robustness.

CAUTION: Exposure to ultraviolet (UV) light can degrade the data stored in EEPROM cells. Therefore,
customers who use a WLCSP package must ensure that exposure to ultraviolet light does not occur.
2. For wafer sales, please contact Atmel Sales.
Package Type
8S1
8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8U-10
4-ball, 4x4 Grid Array, Wafer Level Chip Scale Package (WLCSP)
20
Form
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
10.
Part Marking Scheme
AT25M02: Package Marking Information
8-ball WLCSP
8-lead SOIC
ATMLHYWW
## % @
AAAAAAAA
ATMLUYWW
## %
@
AAAAAAAA
Note 1:
designates pin 1
Note 2: Package drawings are not to scale
Catalog Number Truncation
AT25M02
Date Codes
Y = Year
2: 2012
3: 2013
4: 2014
5: 2015
Truncation Code ##: 5H
Voltages
6: 2016
7: 2017
8: 2018
9: 2019
M = Month
A: January
B: February
...
L: December
WW = Work Week of Assembly
02: Week 2
04: Week 4
...
52: Week 52
Country of Assembly
Lot Number
@ = Country of Assembly
AAA...A = Atmel Wafer Lot Number
Trace Code
% = Minimum Voltage
M: 1.7V min
D: 2.5V min
Grade/Lead Finish Material
U: Industrial/SnAgCu
H: Industrial/NiPdAu
Atmel Truncation
XX = Trace Code (Atmel Lot Numbers Correspond to Code)
Example: AA, AB.... YZ, ZZ
AT: Atmel
ATM: Atmel
ATML: Atmel
5/6/15
TITLE
Package Mark Contact:
[email protected]
25M02SM, AT25M02 Standard Package Marking Information
DRAWING NO.
REV.
25M02SM
C
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
21
11.
Packaging Information
11.1
8S1 — 8-lead JEDEC SOIC
C
1
E
E1
L
N
Ø
TOP VIEW
END VIEW
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
A1
D
SIDE VIEW
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
MIN
NOM
MAX
–
–
1.75
A1
0.10
–
0.25
b
0.31
–
0.51
C
0.17
–
0.25
SYMBOL
A
D
4.90 BSC
E
6.00 BSC
E1
3.90 BSC
e
1.27 BSC
L
0.40
–
1.27
Ø
0°
–
8°
NOTE
3/6/2015
Package Drawing Contact:
[email protected]
22
TITLE
8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
GPC
SWB
DRAWING NO.
REV.
8S1
H
11.2
8U-10 — 8-ball WLCSP
TOP VIEW
BOTTOM SIDE
k
12
A1 CORNER
0.015 (4X)
A
34
43
A
A
B
B
21
e1
E
C
C
D
D
D
e
d1
d2
B
SIDE VIEW
A
A1 CORNER
db
v
A2
d0.015 m C
d0.05 m C A B
SEATING PLANE
C
k
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
0.20 C
PIN ASSIGNMENT MATRIX
SYMBOL
MIN
TYP
MAX
A
0.313
0.334
0.355
A1
—
0.094
—
1
2
3
4
A2
—
0.240
—
A
n/a
VCC
CS
n/a
D
B
n/a
HOLD
n/a
SO
d1
1.00 BSC
d2
1.40 BSC
C
SCK
n/a
n/a
WP
D
n/a
SI
GND
n/a
E
3
Contact Atmel for details
Contact Atmel for details
e
0.50 BSC
e1
2.10 BSC
b
NOTE
0.170
0.185
0.200
Note: 1. Dimensions are NOT to scale.
2. Solder ball composition is 95.5Sn-4.0Ag-0.5Cu.
3. Product offered with Back Side Coating
9/22/15
Package Drawing Contact:
[email protected]
TITLE
8U-11, 8-ball 4x4 Array, Custom Pitch
Wafer Level Chip Scale Package (WLCSP)
GPC
DRAWING NO.
REV.
GAC
8U-10
E
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
23
12.
24
Revision History
Doc. Rev.
Date
Comments
8832B
02/2016
Removed preliminary status and updated 8U-10 package drawing.
8832A
05/2015
Initial document release.
AT25M02 [DATASHEET]
Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2016 Atmel Corporation. / Rev.: Atmel-8832B-SEEPROM-AT25M02-Datasheet_022016.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.