AT88SC0404C - Summary

AT88SC0404C
Atmel CryptoMemory, 4-Kbit
SUMMARY DATASHEET
Features
•
•
One of a family of nine devices with user memories from 1-Kbit to 256-Kbit
4-Kbit (512-byte) EEPROM user memory
•
•
•
•
•
Four 128-byte (1-Kbit) zones
Self-timed write cycle
Single byte or 16-byte page write mode
Programmable access rights for each zone
2-Kbit configuration zone
• 37-byte OTP area for user-defined codes
• 160-byte area for user-defined keys and passwords
•
High security features
•
•
•
•
•
•
•
•
Smart card features
•
•
•
•
•
•
•
ISO 7816 Class A (5V) or Class B (3V) operation
ISO 7816-3 asynchronous T = 0 protocol (Gemplus® patent) *
Multiple zones, key sets and passwords for multi-application use
Synchronous 2-wire serial interface for faster device initialization *
Programmable 8-byte answer-to-reset register
ISO 7816-2 compliant modules
Embedded application features
•
•
•
•
•
•
•
64-bit Mutual Authentication Protocol (under license of ELVA)
Encrypted checksum
Stream encryption
Four key sets for authentication and encryption
Eight sets of two 24-bit passwords
Anti-tearing function
Voltage and frequency monitor
Low voltage operation: 2.7V to 5.5V
Secure nonvolatile storage for sensitive system or user information
2-wire serial interface
1.0MHz compatibility for fast operation
Standard 8-lead plastic packages, green compliant (exceeds RoHS)
Same pinout as 2-wire Serial EEPROMs
High reliability
• Endurance: 100,000 cycles
• Data retention: 10 years
• ESD protection: 4,000V min
This is a summary document.
The complete document is
available on the Atmel website
at www.atmel.com.
* Note: Modules available with either T=0 / 2-wire modes or 2-wire mode only
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
Table 1.
Pin Assignment
Pad
Description
ISO Module
TWI Module
Standard Package Pin
VCC
Supply Voltage
C1
C1
8
GND
Ground
C5
C5
4
SCL/CLK
Serial Clock Input
C3
C3
6
SDA/IO
Serial Data Input/Output
C7
C7
5
RST
Reset Input
C2
NC
NC
Figure 1.
Pin Configuration
ISO Smart Card Module
VCC=C1
RST=C2
SCL/CLK=C3
NC=C4
C5=GND
C6=NC
C7=SDA/IO
C8=NC
8-lead SOIC, PDIP
NC
NC
1
8
VCC
2
7
NC
GND
3
6
NC
SCL
4
5
SDA
TWI Smart Card Module
VCC=C1
NC=C2
SCL/CLK=C3
NC=C4
1.
C5=GND
C6=NC
C7=SDA/IO
C8=NC
Description
®
®
The Atmel AT88SC0404C member of the CryptoMemory family is a high-performance secure memory providing 4-Kbits of
user memory with advanced security and cryptographic features built in. The user memory is divided into four 128-byte zones,
each of which may be individually set with different security access rights or effectively combined together to provide space for
one to four data files.
1.1
Smart Card Applications
The AT88SC0404C provides high security, low cost, and ease of implementation without the need for a microprocessor
operating system. The embedded cryptographic engine provides for dynamic and symmetric mutual authentication between
the device and host, as well as performing stream encryption for all data and passwords exchanged between the device and
host. Up to four unique key sets may be used for these operations. The AT88SC0404C offers the ability to communicate with
virtually any smart card reader using the asynchronous T = 0 protocol (Gemplus Patent) defined in ISO 7816-3.
1.2
Embedded Applications
Through dynamic and symmetric mutual authentication, data encryption, and the use of encrypted checksums, the
AT88SC0404C provides a secure place for storage of sensitive information within a system. With its tamper detection circuits,
this information remains safe even under attack. A 2-wire serial interface running at 1.0MHz is used for fast and efficient
communications with up to 15 devices that may be individually addressed. The AT88SC0404C is available in industry standard
8-lead packages with the same familiar pinout as 2-wire Serial EEPROMs.
2
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
Figure 1-1. Block Diagram
VCC
GND
SCL/CLK
SDA/IO
RST
Power
Management
Authentication,
Encryption and
Certification Unit
Synchronous
Interface
Data Transfer
Asynchronous
ISO Interface
Password
Verification
Reset Block
Answer to Reset
2.
Pin Descriptions
2.1
Supply Voltage (VCC)
Random
Generator
EEPROM
The VCC input is a 2.7V to 5.5V positive voltage supplied by the host.
2.2
Clock (SCL/CLK)
In the asynchronous T = 0 protocol, the SCL/CLK input is used to provide the device with a carrier frequency f. The nominal
length of one bit emitted on I/O is defined as an “elementary time unit” (ETU) and is equal to 372/ f. When the synchronous
protocol is used, the SCL/CLK input is used to positive edge clock data into the device and negative edge clock data out of the
device.
2.3
Reset (RST)
The AT88SC0404C provides an ISO 7816-3 compliant asynchronous answer to reset sequence. When the reset sequence is
activated, the device will output the data programmed into the 64-bit answer-to-reset register. An internal pull-up on the RST
input pad allows the device to be used in synchronous mode without bonding RST. The AT88SC0404C does not support the
synchronous answer-to-reset sequence.
2.4
Serial Data (SDA/IO)
The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wired with any number of other
open drain or open collector devices. An external pull-up resistor should be connected between SDA and VCC. The value of
this resistor and the system capacitance loading the SDA bus will determine the rise time of SDA. This rise time will determine
the maximum frequency during read operations. Low value pull-up resistors will allow higher frequency operations while
drawing higher average power. SDA/IO information applies to both asynchronous and synchronous protocols.
When the synchronous protocol is used, the SCL/CLK input is used to positive edge clock data into the device and negative
edge clock data out of the device.
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
3
3.
Absolute Maximum Ratings*
Operating temperature.................... −40°C to +85°C
Storage temperature ................... −65°C to + 150°C
Voltage on any pin
with respect to ground ...............− 0.7 to VCC +0.7V
Maximum operating voltage ............................. 6.0V
DC output current ......................................... 5.0mA
Table 3-1.
*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at these or any other condition
beyond those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of
time may affect device reliability.
DC Characteristics
Applicable over recommended operating range from VCC = +2.7 to 5.5V, TAC = -40°C to +85°C (unless otherwise noted)
Symbol
Parameter
(2)
VCC
Supply Voltage
ICC
Supply Current (VCC = 5.5V)
ICC
Max
Units
5.5
V
Async READ at 3.57MHz
5
mA
Supply Current (VCC = 5.5V)
Async WRITE at 3.57MHz
5
mA
ICC
Supply Current (VCC = 5.5V)
Synch READ at 1MHz
5
mA
ICC
Supply Current (VCC = 5.5V)
Synch WRITE at 1MHz
5
mA
ISB
Min
Standby Current (VCC = 5.5V)
VIN = VCC or GND
100
mA
2.7
Typ
VIL
(1)
SDA/IO Input Low Threshold
0
VCC x 0.2
V
VIL
(1)
SCL/CLK Input Low Threshold
0
VCC x 0.2
V
VIL
(1)
RST Input Low Threshold
0
VCC x 0.2
V
VIH
(1)(2)
SDA/IO Input High Threshold
VCC x 0.7
VCC
V
(1)(2)
VIH
SCL/CLK Input High Threshold
VCC x 0.7
VCC
V
(1)(2)
VIH
RST Input High Threshold
VCC x 0.7
VCC
V
IIL
SDA/IO Input Low Current
0 < VIL < VCC x 0.15
15
µA
IIL
SCL/CLK Input Low Current
0 < VIL < VCC x 0.15
15
µA
IIL
RST Input Low Current
0 < VIL < VCC x 0.15
50
µA
IIH
SDA/IO Input High Current
VCC x 0.7 < VIH < VCC
20
µA
IIH
SCL/CLK Input High Current
VCC x 0.7 < VIH < VCC
100
µA
IIH
RST Input High Current
VCC x 0.7 < VIH < VCC
150
µA
VOH
SDA/IO Output High Voltage
20K ohm external pull-up
VCC x 0.7
VCC
V
VOL
SDA/IO Output Low Voltage
IOL = 1mA
0
VCC x 0.15
V
IOH
SDA/IO Output High Current
VOH
20
µA
Note:
4
Test Condition
1.
VIL min and VIH max are reference only and are not tested
2.
To prevent latch up conditions from occurring during power up of the AT88SCxxxxC, VCC must be turned on
before applying VIH. For powering down, VIH must be removed before turning VCC off
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
Table 3-2.
AC Characteristics
Applicable over recommended operating range from VCC = +2.7 to 5.5V,
TAC = -40°C to +85°C, CL = 30pF (unless otherwise noted)
4.
Symbol
Parameter
Min
Max
Units
fCLK
Async Clock Frequency (VCC Range: +4.5 - 5.5V)
1
5
MHZ
fCLK
Async Clock Frequency (VCC Range: +2.7 - 3.3V)
1
4
MHZ
fCLK
Synch Clock Frequency
0
1
MHZ
Clock Duty cycle
40
60
%
tR
Rise Time - I/O, RST
1
µS
tF
Fall Time - I/O, RST
1
µS
tR
Rise Time - CLK
9% x period
µS
tF
Fall Time - CLK
9% x period
µS
tAA
Clock Low to Data Out Valid
35
nS
tHD.STA
Start Hold Time
200
nS
tSU.STA
Start Set-up Time
200
nS
tHD.DAT
Data In Hold Time
10
nS
tSU.DAT
Data In Set-up Time
100
nS
tSU.STO
Stop Set-up Time
200
nS
tDH
Data Out Hold Time
20
nS
tWR
Write Cycle Time (at 25°C)
5
mS
tWR
Write Cycle Time (-40° to +85°C)
7
mS
Device Operation for Synchronous Protocols
Clock and Data Transitions:
The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time
periods (see Figure 4-3 on page 7). Data changes during SCL high periods will indicate a start or stop condition as defined
below.
Start Condition:
A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 4-4 on
page 7).
Stop Condition:
A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the
EEPROM in a standby power mode (see Figure 4-4 on page 7).
Acknowledge:
All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero to
acknowledge that it has received each word. This happens during the ninth clock cycle (see Figure 4-5 on page 7).
Memory Reset:
After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps:
1.
2.
3.
Clock up to nine cycles
Look for SDA high in each cycle while SCL is high
Create a start condition
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
5
Figure 4-1. Bus Timing for 2-wire Communications
SCL: Serial Clock, SDA – Serial Data I/O
tHIGH
tF
tR
tLOW
tLOW
SCL
tSU.STA
tHD.STA
tHD.DAT
tSU.DAT
tSU.STO
SDA IN
tDH
tAA
tBUF
SDA OUT
Figure 4-2. Write Cycle Timing: SCL:
Serial Clock, SDA – Serial Data I/O
SCL
SDA
8th BIT
ACK
WORDn
twr
STOP
CONDITION
Note:
6
(1)
START
CONDITION
The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal
clear/write cycle
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
Figure 4-3. Data Validity
SDA
SCL
DATA STABLE
DATA STABLE
DATA
CHANGE
ALLOWED
Figure 4-4. Start and Stop Definitions
SDA
SCL
START
STOP
Figure 4-5. Output Acknowledge
1
SCL
8
9
DATA IN
DATA OUT
START
ACKNOWLEDGE
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
7
5.
Device Architecture
5.1
User Zones
The EEPROM user memory is divided into four zones of 1024 bits each. Multiple zones allow for different types of data or files
to be stored in different zones. Access to the user zones is allowed only after security requirements have been met. These
security requirements are defined by the user during the personalization of the device in the configuration memory. If the same
security requirements are selected for multiple zones, then these zones may effectively be accessed as one larger zone.
Figure 5-1. User Zones
Zone
$0
$1
$2
$3
$4
$5
$6
$7
$00
User 0
─
128 bytes
─
$78
$00
User 1
─
128 bytes
─
$78
$00
User 2
─
128 bytes
─
$78
$00
User 3
─
128 bytes
─
$78
6.
Control Logic
Access to the user zones occurs only through the control logic built into the device. This logic is configurable through access
registers, key registers and keys programmed into the configuration memory during device personalization. Also implemented
in the control logic is a cryptographic engine for performing the various higher-level security functions of the device.
8
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
7.
Configuration Memory
The configuration memory consists of 2048 bits of EEPROM memory used for storing passwords, keys and codes and for
defining security levels to be used for each user zone. Access rights to the configuration memory are defined in the control
logic and may not be altered by the user.
Figure 7-1. Configuration Memory
$0
$1
$2
$3
$00
$08
$4
$5
$6
$7
Answer to Reset
Fab Code
MTZ
$10
Identification
Card Manufacturer Code
Lot History Code
$18
DCR
$20
AR0
Read Only
Identification Number Nc
PR0
AR1
PR1
AR2
PR2
AR3
PR3
$28
$30
Reserved
Access Control
$38
$40
Issuer Code
$48
$50
$58
$60
$68
$70
For Authentication and Encryption use
Cryptography
For Authentication and Encryption use
Secret
$78
$80
$88
$90
$98
$A0
$A8
$B0
PAC
Write 0
PAC
Read 0
$B8
PAC
Write 1
PAC
Read 1
$C0
PAC
Write 2
PAC
Read 2
$C8
PAC
Write 3
PAC
Read 3
$D0
PAC
Write 4
PAC
Read 4
$D8
PAC
Write 5
PAC
Read 5
$E0
PAC
Write 6
PAC
Read 6
$E8
PAC
Write 7
PAC
Read 7
$F0
$F8
Reserved
Password
Forbidden
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
9
8.
Security Fuses
There are three fuses on the device that must be blown during the device personalization process. Each fuse locks certain
portions of the configuration memory as OTP memory. Fuses are designed for the module manufacturer, card manufacturer
and card issuer and should be blown in sequence, although all programming of the device and blowing of the fuses may be
performed at one final step.
9.
Protocol selection
The AT88SC0404C supports two different communication protocols.
•
Smart Card Applications:
The asynchronous T = 0 protocol defined by ISO 7816-3 is used for compatibility with the industry’s standard smart
card readers
•
Embedded Applications:
A 2-wire serial interface is used for fast and efficient communication with logic or controllers
The power-up sequence determines which of the two communication protocols will be used.
9.1
Asynchronous T = 0 Protocol
This power-up sequence complies with ISO 7816-3 for a cold reset in smart card applications.
•
•
•
•
VCC goes high; RST, I/O-SDA and CLK-SCL are low
Set I/O-SDA in receive mode
Provide a clock signal to CLK-SCL
RST goes high after 400 clock cycles
The device will respond with a 64-bit ATR code, including historical bytes to indicate the memory density within the
CryptoMemory family. Once the asynchronous mode has been selected, it is not possible to switch to the synchronous mode
without powering off the device.
Figure 9-1. Asynchronous T = 0 Protocol (Gemplus Patent)
Vcc
I/O-SDA
RST
CLK-SCL
10
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
ATR
9.2
Synchronous 2-wire Serial Interface
The synchronous mode is the default after powering up VCC due to an internal pull-up on RST. For embedded applications
using CryptoMemory in standard plastic packages, this is the only communication protocol.
•
•
Power-up VCC, RST goes high also
After stable VCC, CLK-SCL and I/O-SDA may be driven
Figure 9-2. Synchronous 2-wire Protocol
Vcc
I/O-SDA
RST
1
CLK-SCL
Note:
10.
2
4
3
5
Five clock pulses must be sent before the first command is issued
Communication Security Modes
Communications between the device and host operate in three basic modes. Standard mode is the default mode for the
device after power-up. Authentication mode is activated by a successful authentication sequence. Encryption mode is
activated by a successful encryption activation following a successful authentication.
Table 10-1. Communication Security Modes
Mode
(1)
Configuration Data
User Data
Passwords
Standard
clear
clear
clear
MDC
Authentication
clear
clear
encrypted
MAC
Encryption
clear
encrypted
encrypted
MAC
Note:
1.
Data Integrity Check
(1)
(1)
(1)
Configuration data include viewable areas of the Configuration Zone except the passwords:


MDC: Modification Detection Code
MAC: Message Authentication Code
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
11
11.
Security Options
11.1
Anti-tearing
In the event of a power loss during a write cycle, the integrity of the device’s stored data may be recovered. This function is
optional: the host may choose to activate the anti-tearing function, depending on application requirements. When anti-tearing
is active, write commands take longer to execute, since more write cycles are required to complete them, and data are limited
to eight bytes.
Data are written first to a buffer zone in EEPROM instead of the intended destination address, but with the same access
conditions. The data are then written in the required location. If this second write cycle is interrupted due to a power loss, the
device will automatically recover the data from the system buffer zone at the next power-up.
In 2-wire mode, the host is required to perform ACK polling for up to 8mS after write commands when anti-tearing is active. At
power-up, the host is required to perform ACK polling, in some cases for up to 2mS, in the event that the device needs to carry
out the data recovery process.
11.2
Write Lock
If a user zone is configured in the write lock mode, the lowest address byte of an 8-byte page constitutes a write access byte
for the bytes of that page.
Example:
The write lock byte at $080 controls the bytes from $080 to $087
Figure 11-1. Write Lock Example
Address
$080
$0
$1
$2
$3
$4
$5
$6
$7
11011001
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
locked
locked
locked
The write lock byte may also be locked by writing its least significant (rightmost) bit to “0”. Moreover, when write lock mode is
activated, the write lock byte can only be programmed — that is, bits written to “0” cannot return to “1”.
In the write lock configuration, only one byte can be written at a time. Even if several bytes are received, only the first byte will
be taken into account by the device.
12
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
12.
Password Verification
Passwords may be used to protect read and/or write access of any user zone. When a valid password is presented, it is
memorized and active until power is turned off, unless a new password is presented or RST becomes active. There are eight
password sets that may be used to protect any user zone. Only one password is active at a time, but write passwords give
read access also.
12.1
Authentication Protocol
The access to a user zone may be protected by an authentication protocol. Any one of four keys may be selected to use with a
user zone.
The authentication success is memorized and active as long as the chip is powered, unless a new authentication is initialized
or RST becomes active. If the new authentication request is not validated, the card loses its previous authentication and it
should be presented again. Only the last request is memorized.
Note:
Password and authentication may be presented at any time and in any order. If the trials limit has been reached
(after four consecutive incorrect attempts), the password verification or authentication process will not be taken
into account
Figure 12-1. Password and Authentication Operations
Device (Card)
Card Number
Host (Reader)
AUTHENTICATION
VERIFY A
COMPUTE Challenge B
Challenge A
Challenge B
VERIFY RPW
DATA
Checksum (CS)
VERIFY WPW
VERIFY CS
COMPUTE Challenge A
VERIFY B
READ ACCESS
Read Password (RPW)
VERIFY CS
WRITE ACCESS
Write Password (WPW)
DATA
CS
Write DATA
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
13
12.2
Checksum
The AT88SC0404C implements a data validity check function in the form of a checksum, which may function in standard,
authentication or encryption modes.
In the standard mode, the checksum is implemented as a Modification Detection Code (MDC), in which the host may read an
MDC from the device in order to verify that the data sent was received correctly.
In the authentication and encryption modes, the checksum becomes more powerful since it provides a bidirectional data
integrity check and data origin authentication capability in the form of a Message Authentication Code (MAC). Only the
host/device that carried out a valid authentication is capable of computing a valid MAC. While operating in the authentication
or encryption modes, the use of a MAC is required. For an ingoing command, if the device calculates a MAC different from the
MAC transmitted by the host, not only is the command abandoned but the mode is also reset. A new authentication and/or
encryption activation will be required to reactivate the MAC.
12.3
Encryption
The data exchanged between the device and the host during read, write and verify password commands may be encrypted to
ensure data confidentiality.
The issuer may choose to require encryption for a user zone by settings made in the configuration memory. Any one of four
keys may be selected for use with a user zone. In this case, activation of the encryption mode is required in order to read/write
data in the zone and only encrypted data will be transmitted. Even if not required, the host may elect to activate encryption
provided the proper keys are known.
12.4
Supervisor Mode
Enabling this feature allows the holder of one specific password to gain full access to all eight password sets, including the
ability to change passwords.
12.5
Modify Forbidden
No write access is allowed in a user zone protected with this feature at any time. The user zone must be written during device
personalization prior to blowing the security fuses.
12.6
Program Only
For a user zone protected by this feature, data within the zone may be changed from a “1” to a “0”, but never from a “0” to a
“1”.
13.
Initial Device Programming
To enable the security features of CryptoMemory, the device must first be personalized to set up several registers and load in
the appropriate passwords and keys. This is accomplished through programming the configuration memory of CryptoMemory
using simple write and read commands. To gain access to the configuration memory, the secure code must first be
successfully presented. For the AT88SC0404C device, the secure code is $60 57 34. After writing and verifying data in the
configuration memory, the security fuses must be blown to lock this information in the device. For additional information on
personalizing CryptoMemory, please see the application notes Programming CryptoMemory for Embedded Applications and
Initializing CryptoMemory for Smart Card Applications (at www.Atmel.com).
14
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
14.
Ordering Information
Atmel Ordering Code
Package
Voltage Range
Temperature Range
AT88SC0404C-MJ
AT88SC0404C-MP
AT88SC0404C-MJTG
AT88SC0404C-MPTG
M2 – J Module - ISO
M2 – P Module - ISO
M2 – J Module - TWI
M2 – P Module - TWI
2.7V–5.5V
Commercial (0°C–70°C)
AT88SC0404C-PU
AT88SC0404C-SH
8P3
8S1
2.7V–5.5V
Green compliant (exceeds RoHS)
Industrial (−40°C–85°C)
AT88SC0404C-WI
7 mil wafer
2.7V–5.5V
Industrial (−40°C–85°C)
Package Type
(1) (2)
Description
M2 – J Module : ISO or TWI
M2 ISO 7816 smart card module
M2 – P Module : ISO or TWI
M2 ISO 7816 smart card module with Atmel logo
8P3
8-lead, 0.300” wide, Plastic Dual Inline (PDIP)
8S1
8-lead, 0.150” wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
Note:
®
1.
Formal drawings may be obtained from an Atmel sales office
2.
Both the J and P module packages are used for either ISO (T=0 / 2-wire mode) or TWI (2-wire mode only)
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
15
15.
Packaging Information
Ordering Code: MJ or MJTG
Note:
16
Ordering Code: MP or MPTG
Module Size:
M2
Dimension*:
12.6 x 11.4 [mm]
Glob Top:
Thickness:
Pitch:
Round - ∅ 8.5 [mm]
0.58 [mm]
14.25mm
Module Size:
Dimension*:
Glob Top:
Thickness:
Pitch:
M2
12.6 x 11.4 [mm]
Square - 8.8 x 8.8 [mm]
0.58 [mm]
14.25mm
*The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions
of the module after excise or punching from the carrier tape are generally 0.4mm greater in both directions
(i.e., a punched M2 module will yield 13.0 x 11.8mm)
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
15.1
Atmel AT88SC0404C Package Marking Information
AT88SC0404C: Package Marking Information
8-lead PDIP
8-lead SOIC
AT88SC
0404C
U
YYWW
AT88SC
0404C
H YMXX @
No Bottom side mark (this package)
Note 1:
designates pin 1
Note 2: Package drawings are not to scale
Date Codes
YY = Year
12: 2012
13: 2013
14: 2014
15: 2015
Grade/Lead Finish Material
WW = Work Week of Assembly
02:Week 2
04:Week 4
...
52:Week 52
Y = Year
2: 2012
3: 2013
4: 2014
5: 2015
M = Month
A = January
B = February
...
L = December
Country of Assembly
Lot Number
@ = Country of Assembly
Marked on Bottom side unless in
Injector Mold for PDI P only!
Marked on Bottom side for the PDI P only!
U:
H:
Industrial/Matte Tin
Industrial/NiPdAu
Atmel Truncation
AT:
Atmel
Trace Code
XX = Trace Code (Atmel Lot Numbers to Correspond to Code)
Example: AA, AB.... YZ, ZZ
3/5/12
TITLE
Package Mark Contact:
[email protected]
88SC0404CSM, AT88SC0404C Package Marking Information
DRAWING NO.
REV.
88SC0404CSM
A
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
17
15.2
Ordering Code: SH
8S1 – 8-lead JEDEC SOIC
C
1
E
E1
L
N
Ø
TOP VIEW
e
END VIEW
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
A1
D
SIDE VIEW
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
SYMBOL MIN
A
1.35
NOM
MAX
–
1.75
A1
0.10
–
0.25
b
0.31
–
0.51
C
0.17
–
0.25
D
4.80
–
5.05
E1
3.81
–
3.99
E
5.79
–
6.20
e
L
NOTE
1.27 BSC
0.40
–
1.27
0°
–
8°
6/22/11
Package Drawing Contact:
[email protected]
18
TITLE
8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
GPC
SWB
DRAWING NO.
REV.
8S1
G
15.3
Ordering Code: PU
8P3 – 8-lead PDIP
E
1
E1
N
Top View
c
eA
End View
D
D1
COMMON DIMENSIONS
(Unit of Measure = inches)
e
b2
b3
NOM
MAX
A2
0.115
0.130
0.195
b
0.014
0.018
0.022
5
b2
0.045
0.060
0.070
6
b3
0.030
0.039
0.045
6
c
0.008
0.010
0.014
D
0.355
0.365
0.400
D1
0.005
E
0.300
0.310
0.325
4
E1
0.240
0.250
0.280
3
A
L
b
4 PLCS
MIN
SYMBOL
A2 A
e
Side View
1.
2.
3.
4.
5.
6.
2
3
3
0.100 BSC
eA
L
Notes:
0.210
NOTE
0.300 BSC
0.115
0.130
4
0.150
2
This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.
Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
E and eA measured with the leads constrained to be perpendicular to datum.
Pointed or rounded lead tips are preferred to ease insertion.
b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
06/21/11
Package Drawing Contact:
[email protected]
TITLE
GPC
DRAWING NO.
8P3, 8-lead, 0.300” Wide Body, Plastic Dual
In-line Package (PDIP)
PTC
8P3
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
REV.
D
19
16.
Revision History
Doc. Rev.
Date
Comments
2023MS
12/2013
Add package marking information.
Update Atmel logos and disclaimer page.
2023LS
12/2011
Update template.
Update package drawings.
Change AT88SC0104C-SU to AT88SC0104C-SH.
2023KS
08/2009
SB - TWI Package update.
2023JS
03/2009
Features Section – add ‘green compliant (exceeds RoHS) to end of ‘Standard 8-lead plastic
packages’ bullet.
Add note to DC characteristics table and applied to VCC and all three instances of Vih
symbols in table.
Ordering Information page: Add ‘Green compliant (exceeds RoHS) to middle row of
temperature range.
Replace ‘Lead-free/Halogen-free. Keep industrial.
Updated to 2009 Copyright.
2023IS
11/2008
Update timing diagrams.
2023HS
04/2007
Final release version.
2023HS
03/2007
Implemented revision history.
Remove industrial package offerings.
Remove 8Y4 offering.
Replace user zone, memory configuration, and write lock example tables with new
information.
20
AT88SC0404C [SUMMARY DATASHEET]
Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
│
www.atmel.com
© 2013 Atmel Corporation. / Rev.: Atmel-2023MS-CryptoMem-AT88SC0404C-Datasheet-Summary_122013.
Atmel®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. ARM®, ARM
Connected® logo, and others are the registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is
granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL
WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE
FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to
make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically
provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in
applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the
failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written consent. SafetyCritical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not
designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for
use in automotive applications unless specifically designated by Atmel as automotive-grade.