701 Series
Remote Power Controllers
Up to 200 Amps • Form X
Magnetic Latching
For DC only applications
SPECIFICATIONS
GENERAL
Rupture (main contacts) ..........................3600 Amperes
Contact Arrangement ...........................SPST (1 Form X)
Weight............................................................... 15 oz max.
Designed to meet the requirements of MIL-C-83383
Response Time: .............................................12 ms nom.
PERFORMANCE
Contact Ratings (Note 1):
Power Contacts:
All loads........................Up to 200 Amps @ 28 VDC
Current Trip Points.................................... Trip Time
1000% of Rated Current ....................1.0 Sec. max.
400% of Rated Current.....................10.0 Sec. max.
200% of Rated Current.....................60.0 Sec. max.
138% of Rated Current......................1.0 Hour max.
Up to 115% of Rated Current....................... No Trip
Tolerances:
Current .............................................................±10%
Time .................................................................±10%
Auxiliary Contacts:
Configuration................................................... SPDT
Current Rating ...........................5 Amps @ 28 VDC
Life
...............50,000 cycles @ rated Res. and Ind. load
25,000 cycles @ rated Motor load
100,000 cycles mechanical
NOTES:
1. For other ratings or calibrations consult the factory.
Contact Bounce Time....................................... 2 ms max
@ rated contact load, 28 VDC
Contact Voltage Drop:
Initial ......................................225 mv @ Rated Current
End of Life .............................250 mv @ Rated Current
Operating Voltage:
Nominal DC Voltage................................ 18 to 32 VDC
ENVIRONMENTAL
o
o
Temperature Range ................................. -54 C to +71 C
Vibration (Note 2)..............................10 G'S 50 - 2000 Hz
Shock (Operating)(Note 2) ......................... 25 G's 11 ms
Acceleration ............................................................... 15 G
ELECTRICAL CHARACTERISTICS
Duty Cycle........................................................Intermittent
Insulation Resistance............................... 100 megohms
o
@ 500V 25 C
Dielectric Strength:
Sea Level:
Contact to Case ................................... 1,500 VRMS
Contact to Coil ..................................... 1,500 VRMS
Coil to Case ......................................... 1,500 VRMS
Across Open Contacts ........................ 1,350 VRMS
50,000 Feet:
All Points ................................................. 500 VRMS
2.
For applications requiring higher shock and vibration,
consult the factory.
14930 E. Alondra Blvd., La Mirada, CA 90638-5752 (714) 994-6500 FAX (714) 994-3013
W:2000, Rev. 4
701 Series
The 701 Remote Power Controllers are designed to sense the current level flowing through their contacts, and to open the circuit
when the current exceeds the specified current rating. These units use our unique magnetic latching motor design to minimize
power consumption. These units are fully temperature compensated for accurate operation over the full temperature range.
The 701 circuitry has 1500 watts of Peak Power Dissipation transient suppression built in so it can withstand the rigors of even the
noisiest of supply voltages. Utilizing all space age approved materials, the 701 Remote Power Controllers are ideal for
demanding applications.
R.P.C. Type
Nominal Current Rating
"A" indicates SPDT Auxiliary switch
701 - 150
OVERALL DIMENSIONS
SCHEMATIC
A
SELECTION TABLE
Catalog
Number
Continuous
Ampere Contact
Rating
Thread "B"
Dimension "A"
701-5( )
701-7.5( )
5
7.5
10-32 UNF
10-32 UNF
.500
.500
701-10( )
10
10-32 UNF
.500
701-15( )
15
10-32 UNF
.500
701-20( )
20
10-32 UNF
.500
701-25( )
25
10-32 UNF
.500
701-35( )
35
1/4-28 UNF
.610
701-40( )
40
1/4-28 UNF
.610
701-50( )
50
1/4-28 UNF
.610
701-60( )
60
1/4-28 UNF
.610
701-75( )
75
1/4-28 UNF
.610
701-100( )
100
1/4-28 UNF
.610
701-125( )
125
1/4-28 UNF
.610
701-150( )
150
1/4-28 UNF
.610
701-175( )
175
1/4-28 UNF
.610
701-200( )
200
1/4-28 UNF
.610
TYPICAL WIRING DIAGRAM
TRIP TIME CURVE
GENERAL NOTES
• Unless otherwise specified, all tests made at nominal
o
coil voltages, @ 25 C.
• Unless otherwise specified, tolerances on decimal
dimensions are ± .010".
• For special coil variations, switching configurations,
terminals styles and mounting types, consult the
factory.
• Specifications contained herein are subject to change
without notice.
14930 E. Alondra Blvd., La Mirada, CA 90638-5752 (714) 994-6500 FAX (714) 994-3013
W:2000, Rev. 4