LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE LX1741 / LX1742 BOOST CONVERTER DESIGN HINT AN-22 Application Engineer: Michael Calvert I N T E G R A T E D Copyright 2002 Rev. 1.0, 2002-12-03 P R O D U C T S Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE TABLE OF CONTENTS Introduction............................................................................................................................................3 LX1741 / LX1742 Design Note ..............................................................................................................3 Design Example: LX741 ........................................................................................................................4 Design Summary ...................................................................................................................................8 Power and Thermal Considerations ......................................................................................................8 Design Tools..........................................................................................................................................9 Conclusion...........................................................................................................................................10 LX1741 Sepic ......................................................................................................................................11 LX1742 Application..............................................................................................................................12 LX1742 Output Disconnect..................................................................................................................13 References and Appendix ...................................................................................................................14 Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE INTRODUCTION The LX1741 and LX1742 Boost Controllers offer high efficiency performance and provide power management circuit designers with the ability to approach a broad range of design applications with a flexible and easy-toimplement solution. This application hint provides an overview of these two products and describes their overall functions in regard to practical design applications. Please refer to the LX1741 and LX1742 data sheets for a complete discussion regarding electrical performance and packaging information. Table 1 provides a comparison of the LX1741 and LX1742 features. Internal FET External FET Max VIN ISRC (MAX) VOUT (MAX) Package Type Operating Temp. LX1741 No Yes 6.0V 800mA (rms) Application Dependent MSOP or MLP 0 ~ 70°C LX1742 Yes No 6.0V 25V MSOP 0 ~ 70 C 500mA (rms) TABLE 1 – FEATURES L1 LX1741 AND LX1742 C2 The LX1741 and LX1742 are very similar devices. Both of these controllers implement a Pulse Frequency Modulation-type (PFM) topology and provide designers with a cost effective SMPS controller solution for a variety of real-world battery (e.g., Lithium-Ion) driven applications (e.g., pagers, wireless phones, personal digital assistants, etc…). The LX1741 or LX1742 support a broad range of output voltages and can source over 100mA of output current depending upon input voltage. One particular low current application that benefits from the selection of either the LX1741 or LX1742 includes Liquid Crystal Display (LCD) biasing. Each device has 8 functional pins that are designated as IN (voltage input), OUT (voltage output), CS (current sense – used to set the peak inductor current limit), SHDN (active-low shutdown – disables the controller and reduces supply current to < 1mA), GND (circuit ground), FB (feedback – a resistor divider network is connected between this pin and ground to establish VOUT), ADJ (adjust – provides for external control of the output voltage by up to ±15%), and NDRV (n-channel mosfet driver output – LX1741 only) or, SW (switch – LX1742 only: inductor output & diode (anode) input connection – this pin is high impedance in shutdown mode). Copyright 2002 Rev. 1.0, 2002-12-03 ° NDRV IN SHDN R1 C1 SRC LX1741 FB ADJ CS GND RCS R2 FIGURE 1 – TYPICAL LX1741 APPLICATION CIRCUIT The LX1741 requires an external N-channel MOSFET to complete the DC-DC converter circuit. This feature provides the designer with maximum flexibility regarding the selection of a device that minimizes switching losses for a particular application. The external MOSFET is driven from the NDRV pin and Figure 1 shows a typical LX1741 application circuit. The LX1742 simplifies a portion of the design effort by incorporating the N-channel MOSFET device. Applications that have relaxed efficiency and/or increased reliability requirements benefit from this added feature. Figure 2 illustrates a typical LX1742 application. The LX1742 replaces the NDRV pin (found in the LX1741) with the SW (i.e., switch) pin and requires the inductor’s output and the diode’s anode to be connected to this pin. Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 LX1741/LX1742 BOOST CONVERTER L1 APPLICATION NOTE = 10mV). We will determine R1 using formula 1.0 where VREF = 1.29V or 1.20V for the LX1741 and LX1742 respectively: CR1 Eq 1 SW IN SHDN OUT R1 LX1742 FB CS GND RCS R2 ] FIGURE 2 – TYPICAL LX1742 APPLICATION CIRCUIT Other critical design considerations apply to the selection of the inductor, capacitors, diode and transistor. The designer can minimize inductor size, input ripple current, and output ripple voltage by setting the peak inductor current level to 1.5X the expected maximum DC input current. Low ESR capacitors are recommended because they reduce output voltage ripple induced by the inductor’s switching current. Multi-layer ceramic capacitors with X5R or X7R dielectric make a superior choice because they feature small size, very low ESR, and a temperature stable dielectric. Low ESR electrolytic capacitors such as solid tantalum or OS-CON types are also acceptable (note: a brief review of capacitor types is provided in the Appendix). When choosing the diode, the designer should consider the device’s average and peak current ratings with respect to the application’s output and peak inductor current requirements. We’ll select an R1 value using a 1% resistor that is the closest to 414.3KΩ (i.e., R1 equals 412KΩ). Now, we need to determine the Peak Inductor Therefore, we will start by Current (IPEAK). determining IIN using the efficiency equation where Output Power (POUT) is equal to the Efficiency (η) multiplied by the Input Power (PIN): Eq. 2 POUT = η(PIN ) Recall that power is equal to voltage multiplied by current (i.e., P = V*I). Therefore, we can rewrite the efficiency equation and solve for IIN where, VIN equals 3.6V, VOUT equals 12.0V, IOUT equals 40mA (maximum) and ŋ is estimated from the device’s efficiency versus output current curve. Moreover, the diode’s reverse breakdown voltage characteristic must be capable of withstanding a negative voltage transition that is greater than VOUT. A properly sized Schottky diode will typically meet these requirements for a broad range of applications. Finally, overall circuit efficiency is further enhanced by selecting a MOSFET device that exhibits a low RDS(ON) and gate charge characteristic. Typical Efficiency versus Output Current Curves for the LX1741 and LX1742 are shown in Figure 3.0 and Figure 4.0 respectively. 100 90 Efficiency ADJ [ VOUT - VREF = VREF [ ] 12.0V − 1.29V 49.9KΩ = 414.3KΩ 1.29V R1 = R 2 COUT 80 70 60 50 1 5 15 40 Output Current (mA) FIGURE 3 – LX1741 EFFICIENCY VS. OUTPUT CURRENT (VIN = 3.6V, VOUT = 12V, L = 47µH, RCS = 4KΩ) LX1741 DESIGN EXAMPLE Let’s work through a typical application using the LX1741. We’ll assume that an input voltage supply of 3.6V is available. We need to drive an application that requires an output of 12.0V and 40.0mA (i.e., 480mW). The first step in selecting the desired output voltage is to determine the value of R1 and R2. We’ll start with an R2 value less than 100KΩ to minimize VFB offset error (e.g., IFB*R2 = 200nA*50KΩ Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 LX1741/LX1742 BOOST CONVERTER at 350mA. Figure 6 shows the IPEAK value versus input voltage relationship as inductance values increase from 27µH to 94µH and the RCS value remains fixed at 4KΩ. 100 90 7 80 RCS (Kohms) Efficiency APPLICATION NOTE 70 60 50 1 6 15 40 Output Current (mA) 6 5 4 3 2 2.5 FIGURE 4 – LX1742 EFFICIENCY VS. OUTPUT CURRENT (VIN = 3.6V, VOUT = 12V, L= 47µH, RCS = 4KΩ) An efficiency value of approximately 0.85 is found from the curve in Figure 3. Now, IIN may be estimated as follows: 4.5 Input Voltage (V) FIGURE 5 – RCS (KΩ) VS. INPUT VOLTAGE (Note: IPEAK = 350mA, L = 27µH (bottom), 47µH (middle), 94µH (top), tD = 618ns, IMIN = 145mA) 400 [I × VOUT ] = I IN = OUT η × VIN [40mA × 12V ] = 156mA 0.85 × 3.6V Ipeak (mA) Eq 3 3.5 Now that the input current has been determined, we are ready to calculate the peak inductor current. IPEAK is a function of several parameters, specifically: IMIN, VIN, L, tD, ISCALE, and RCS. VIN is already defined herein as 3.6V. The ELECTRICAL CHARACTERISTICS section of the LX1741 data sheet provides the values parameters IMIN and tD. For this example, we will use the LX1741’s nominal IMIN and ISCALE value of 145mA and 31mA/kΩ respectively (note: these values change to 104mA and 22mA/kΩ respectively for the LX1742). The parameter tD is a switching delay related to the operation of the feedback comparator circuit (see Block diagram in data sheet). A typical value for tD, at 25°C, is 620ns. Microsemi recommends using an inductor (L) value of 47µH (i.e., this value works for a broad power conversion range). A higher inductance value may improve efficiency at the expense of degrading the overall output voltage ripple performance. Inserting a smaller inductance value will degrade efficiency. Moreover, the designer is encouraged to consider IPEAK variation over the input voltage range as a smaller inductance increases IPEAK variation versus a larger inductance. Figure 5 illustrates the RCS versus input voltage relationship as inductance values increase from 27µH to 94µH and the IPEAK value remains fixed Copyright 2002 Rev. 1.0, 2002-12-03 375 350 325 300 275 250 2.5 3.5 4.5 Input Voltage (V) FIGURE 6 – IPEAK (mA) VS. INPUT VOLTAGE (Note: RCS = 4.02KΩ, ISCALE = 31mA/KΩ, L = 27µH (top), 47µH (middle), 94µH (bottom), tD = 618ns, IMIN = 145mA) Using this information, we are ready to determine the RCS value required to set the IPEAK value for our application. From our previous calculation, IIN was determined to be 245mA. We will multiple this number by a factor of 1.5 to ensure that we have sufficient margin (over temperature and device-todevice variability) and reduce the risk of hitting current-limit (continuous-mode operation). Therefore, IPEAK = 1.5(IIN) = 1.5(156)mA = 235mA < 800mARMS (ISRC). Note: The maximum IPEAK value is limited by the ISRC value (max. = 0.8ARMS : LX1741). Now we can solve for RCS by using formula 5 where: Eq 4 VIN t D + (I SCALE × R CS ) hence: L I PEAK = I MIN + Eq 5 1 R CS = I SCALE V I PEAK − I MIN − IN t D or, L Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE 3.6V 1 620ns = 1317Ω 235mA − 145mA 32mA/KΩ 47µH RCS = We select an RCS value using 1% resistors that is the closest to the calculated RCS value; hence, RCS equals 1.37KΩ. Connecting this resistor (RCS) between the CS pin and ground sets the IPEAK value in circuit. Now that we have determined values for R1, IPEAK, and RCS, what about calculating the output ripple voltage? The total output ripple voltage is determined from formula 6: Eq. 6 VRIPPLE = ∆VDROOP + ∆VOVERSHOOT + 10mV Figure 7A illustrates the (ideal) switching waveform relationships with respect to the Droop and Overshoot voltage. The overshoot voltage occurs when the inductor charging cycle ends and the inductor current is released to the load. The overshoot voltage is a function of the inductor, output capacitor, Peak Inductor Current, output current, input voltage, output voltage, and an estimate of the voltage drop across the diode (e.g., 0.5v). The overshoot voltage is improved by increasing the output capacitance but degrades slightly with increasing input voltage. The droop voltage occurs when the output voltage begins to decrease below the feedback threshold. The droop voltage is a function of the inductor, output capacitor, Peak Inductor Current, output current, input voltage, and an estimate of the voltage drop across the inductor and the FET’s RDS_ON (e.g., 0.5v). Droop voltage improves by increasing either output voltage or output capacitance (or, both). Finally, there is a 10mV transition error voltage associated with the feedback switching circuit that adds to the total output ripple voltage. Figure 7B shows actual waveforms. FIGURE 7B – ACTUAL SWITCHING WAVEFORMS (VIN = 3V, VOUT = 12V, IOUT = 11mA) The delta (∆) VDROOP and VOVERSHOOT are determined from equations 7 and 8 respectively: Eq 7 ∆VDROOP L C (I PK × I OUT ) OUT = VIN − 0.5 Eq 8 ∆VOVERSHOOT 1 × L (I × I )2 PK OUT 2 C OUT = VOUT + 0.5 − VIN Let’s determine the ∆VDROOP for our application example. Recall that in the previous example, IPEAK was determined to be 368mA. We’ll start by using the inductor value of 47mH and choose COUT equal to 4.7mF. Inserting these values into equation 7 and solving for the ∆VDROOP yields the following result: VOVERSHOOT VOUT ∆VDROOP VDROOP (235mA × 50mA ) 47µH 4.7µF = = 37.9mV 3.6v − 0.5v Now let us determine the ∆VOVERSHOOT for our application example: VNDRV ∆VOVERSHOOT IPEAK IL FIGURE 7A – IDEAL SWITCHING WAVEFORMS Copyright 2002 Rev. 1.0, 2002-12-03 1 × 47µH (235mA × 50mA)2 2 4.7µF = 10.6mV = 12v + 0.5v − 3.6v Combining the results of these calculations with formula 6 provides an estimate of 58mV for the output voltage ripple. What if we increased VIN or COUT while holding the other parameters in formula 7 and 8 constant? Figure 8 and Figure 9 illustrate Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 LX1741/LX1742 BOOST CONVERTER Droop Voltage (mV) 40 35 30 25 20 15 10 5 0 2.5 3.5 (Note: IPEAK = 310mA, IOUT = 25mA, COUT =4.7µF (top), and 47µF(bottom)) Overshoot Voltage (mV) Droop and Overshoot Voltage variation versus input voltage for two values of output capacitance. The Droop Voltage curve shows a voltage reduction as VIN increases. The bottom curve (COUT = 47µF) in Figure 8 demonstrates a significant reduction in Droop voltage versus the top curve (COUT = 4.7µF). The Overshoot Voltage curves in Figure 9 demonstrate a slight overshoot voltage increase as VIN increases. However, note that the bottom curve (COUT = 47µF) demonstrates a significant reduction in overshoot voltage value versus the top curve (COUT = 4.7µF). This exercise provides insight into the criticality of selecting the size of the output capacitor for a particular application. The LX1742 demonstrates similar performance characteristic. APPLICATION NOTE 60 50 40 30 20 10 0 2.5 3.5 4.5 Input Voltage (V) FIGURE 9 – ∆VOVERSHOOT VS. INPUT VOLTAGE (Note: IPEAK = 310mA, IOUT = 25mA, COUT = 4.7µF (top), and 47µF (bottom)). 4.5 Input Voltage (V) FIGURE 8 – ∆VDROOP VS. INPUT VOLTAGE Design Parameters (IOUT = 40mA) • VIN = 3.6V • VOUT = 12.0V • IPEAK = 235mA • IOUT = 40mA @ η > 85% • IIN = 156mA (est.) • Output Ripple < 60mV Measured Parameters (IOUT = 5mA) • VIN = 3.60V • VOUT = 11.83V • IPEAK = 238mA • IOUT = 5mA @ η = 86.2% • IIN = 19mA • Output Ripple ~ 45mV Measured Parameters (IOUT = 40mA) • VIN = 3.58V • VOUT = 11.55V • IPEAK = 238mA • IOUT = 40mA @ η = 89.6% • IIN = 144mA • Output Ripple ~ 65mV TABLE 2 – COMPARISON OF DESIGN VS. ACTUAL PERFORMANCE Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE DESIGN SUMMARY Figure 10 and Figure 11 show the actual switching waveforms for the circuit based upon this design exercise. Channel 2 shows the output ripple voltage, channel 3 shows the NDRV output (pin 8: LX1741), and channel 4 shows the inductor current. Figure 10 shows light load (i.e., IOUT = 5mA) waveforms and Figure 11 shows heavy load waveforms (i.e., IOUT = 40mA). Table 2 highlights the variance between the design and measured performance of the circuit. These results show that we have achieved our design requirements (at TA = 25°C). This circuit maintained regulation up to IOUT = 56mA (VOUT = 11.4V) at room temperature. However, some performance variance over the entire operating temperature range is to be expected and should be thoroughly explored by the designer. Finally, the load regulation error - in this example - is approximately 1%.(Note: all scope photos shown in this document were taken using a Tektronix TDS3034B; a Tektronix TCP202 current probe was used for measuring inductor current). FIGURE 11 - LX1741 WAVE FORMS ILOAD = 40mA VIN = 3.6V, VOUT = 11.6V, IPEAK = 238mA, η = 90%, VRIPPLE < 100mV (COUT = 4.7µF) POWER AND THERMAL CONSIDERATIONS Designers often examine the maximum output power capability of a DC-DC controller IC. Both LX1741 and LX1742 are available in the 8-pin MSOP package and this package’s thermal resistance (ΘJA) is 206°C/W. The device datasheets show a maximum (ambient) junction temperature of (70°C) 150°C. However, at 150°C, degradation to the internal voltage reference bandgap circuit will preclude maintaining optimum output voltage regulation. Moreover, product life-time is reduced when operating at such a high junction temperature. Hence, for practical design considerations, we’ll estimate maximum power dissipation using a junction temperature value of 75°C and ambient operating condition of 30°C. Equation 9 describes total power dissipation as a function of maximum junction temperature, ambient temperature, and thermal resistance. Eq 9 PD = FIGURE 10 – LX1741 WAVE FORMS ILOAD = 5mA VIN = 3.6V, VOUT = 11.8V, IPEAK = 238mA, η = 86%, VRIPPLE < 50mV (COUT = 4.7µF) (T ( J max ) − TA ) R ΘJA Therefore, with respect to these operating conditions, the maximum power dissipation for the LX1741 or LX1742 is calculated to be: PD = (75°C − 30°C) = 0.22W 206°C/W Reducing the ambient operating temperature will allow the controller to dissipate more power according to the relationship specified in equation 9. Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 8 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE Reducing the junction temperature improves overall reliability and product life. Equation 10 provides an application specific estimate of the controller’s power dissipation where IQ is the device quiescent current, ISRC is the current through the external FET’s source, RSRC is the internal current sense resistor, D is the duty cycle, fSW is the maximum switching frequency and, Qg is the gate charge of the external FET: Application Notes: LX1741 / 1742 Formula Calculator for AN22). The spreadsheet contains two sheets titled 1741 and 1742. The calculator allows the designer to input values for output voltage, output current, input voltage, output capacitance, inductance, output voltage selection resistor R2, and the current limit resistor RCS. The calculator returns values for estimating output voltage ripple (as a function of droop and overshoot), the output voltage selection resistor R1, the peak current, and the output power. The value of peak current is also calculated at RCS = 0Ω for reference. Now some words of advice: the validity of calculator’s output is dependent upon the validity of the input data. Therefore, here are some guidelines for selecting input values. Eq 10 ( 2 PD(IC) = VIN × I Q (MAX ) + I PEAK × R SRC × D + f SW × VIN × Q g ) Eq 10.1 f SW V = t OFF OUT VIN −1 In this design example, VIN = 3.6V and the maximum quiescent current (IQ) from the LX1741 datasheet is 100mA. The internal current sense resistor’s value is 200mΩ (typical). Duty cycle is an estimate and should be maintained to within 85% under full load. Switching frequency is estimated using equation 10.1 where the converter’s off-time is typically 300ns. Here, the gate charge is associated with the external MOSFET (e.g., the FDV303N lists a maximum gate charge of 2.3nC). Hence, the LX1741 maximum power dissipation for this example is estimated as: 3.6V × 100µA + (235mA)2 × 200mΩ × = 11.8mW 0.85 + 300kHz × 3.6V × 2nC PD(IC) = The estimated power dissipation of the IC controller in this application is less than the power value calculated using equation 9 at TA equals 30°C; therefore, it is safe to proceed with the design. Equation 11 provides an estimate of the LX1742’s controller’s power dissipation. Here, the designer must consider the RDS(ON) and gate charge of the internal MOSFET device. Eq 11 PD(IC) 2 V × I IN Q(MAX) + I PEAK × (R DS(ON) + R SRC ) = × D + fSW × VIN × Qg DESIGN TOOLS After reading all this a designer might think, “so many formulas, so little time?” Fortunately, help is on the way. A simple Excel™ spreadsheet is available at our website to help you quickly assess the impact of varying the design parameters for a particular application (i.e., refer to Article 1310 under Copyright 2002 Rev. 1.0, 2002-12-03 1. The value of R2 should be set so as to minimize error at the VFB input due to offset currents. A value range between 45KΩ and 90KΩ will suffice for most applications. 2. The Inductor (L) value of 47µH is presented as a starting point for most LX1741 and LX1742 application circuits. Remember that selecting the inductor value requires making trade-offs. For example, the inductance value should be sufficient to ensure proper energy storage under worst-case input voltage and on/off-time conditions. Further, the inductor core must not go into saturation. Second, the designer should minimize the device’s DC resistance to reduce power loss (thus improving overall efficiency). System-level EMI, cost, and mechanical size are other factors that influence inductor selection criteria. For LX741 and LX1742 designs, inductance values from 20µH to 100µH will support a broad range of applications. Note that small inductor values tend to increase peak current variance due to deviations in the mean value of the comparator delay (tD). 3. The value of the current limit resistor (RCS) directly affects the value of peak current. The LX1741 and LX1742 have an absolute maximum switch current rating of 800mARMS and 500mARMS respectively. Do not exceed these values. Always use the smallest current limit resistor value that your design can tolerate. Setting the peak current excessively high burns away power and reduces overall efficiency (and battery life!). The LX1741 and LX1742 are designed to support applications that have an output requirement of less than 1.5W. Use this as your guideline. Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 9 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE 4. Input voltage is simple. Do not exceed 6.0V. Start-up is guaranteed at 1.6V for very light loads. solutions. This application note provided a step-bystep design approach for determining critical circuit values such as R1, R2, RCS, L, IPEAK, and COUT. Moreover, relationship curves for RCS, IPEAK, ∆VDROOP, and ∆VOVERSHOOT versus Input voltage were provided to aid in the overall understanding of controller performance. Additional device and application information is available from the LX1741 an LX1742 device datasheets available at www.microsemi.com. 5. Cost and the output voltage ripple essentially define the output capacitor type and value. These two constraints will set the calculator’s limits (see Appendix). CONCLUSION The LX1741 and LX1742 PFM boost-mode controller ICs offer designers a broad range of application Parameter Units Typical IMIN mA 104.0 Notes ISCALE A/kΩ 2.23E-02 IOUT mA 10.0 Application Parameter tD ns 773.0 from datasheet VIN V 3.60 Application Parameter from datasheet from datasheet VOUT V 15.00 Application Parameter R2 Ω 49900 Application Parameter RCS Ω 4020 Application Parameter L COUT VREF µH µF 47.0 Application Parameter 20.0 Application Parameter V 1.200 from datasheet POUT = 150 mW R1 = 573.9 ΚΩ IPEAK = 252.9 mA I PEAK (Rcs=0) = 163.2 mA mV ∆VDROOP = 2 ∆VOVERSHOOT = 6 mV ∆VRIPPLE = 18 mV L VIN CIN SW IN SHDN VOUT OUT R1 LX1742 LX1742 COUT FB ADJ CS GND R CS R2 FIGURE 12 – LX1742 DESIGN CALCULATOR SPREADSHEET Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 10 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE LX1741 SEPIC CR1 UPS5819 C6 1F 10V L1 VBAT VOUT C4 Q1 FDV303N C5 R1 78.7K L2 22 H 25V C2 R7 10K 6.3V C1 GND 50V LX1741 50V R2 49.9K R8 15K SHDN VADJ FIGURE 13 – LX1741 SEPIC: TWO-CELL TO 3.3V (see DN-099A for more information) Efficiency (%) 80% 70% 60% 2 FIGURE 14 – SWITCHING WAVEFORMS (Configuration: VIN = 5V, VOUT = 3.3V, IOUT = 150mA)Channel 1: VOUT (AC coupled; 100mV/div)Channel 2: Switch voltage (DC coupled; 5V/div)Channel 3: L1 Inductor Current (200mA/div.)Channel 4: L2 Inductor Current (200mA/div.) Copyright 2002 Rev. 1.0, 2002-12-03 3 4 5 6 7 Input Voltage FIGURE 15 – EFFICIENCY VS. INPUT VOLTAGE (IOUT = 100mA & 200mA) Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 11 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE LX1742 CR1 UPS5819 3.6V C1 R1 10K + 5V @ 175mA L1 6.3V + C2 U1 C3 OUT SW R3 226K 6.3V FB IN /SHDN ADJ CS GND R4 72K LX1742CDU R2 10K FIGURE 16 – LX1742 3.6V TO 5V BOOST (175mA) (see DN-099B for more information) Efficiency 80% 70% 60% 50% 25 45 65 85 105 125 145 165 185 Output Current FIGURE 18 – EFFICIENCY VS. OUTPUT CURRENT (mA) FIGURE 17 – SWITCHING WAVEFORMS Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 12 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE LX1742 OUTPUT DISCONNECT RBias 147K CR1 UPS5819 3.0V 18.0V L1 + C2 U1 /SHDN + ADJ 35V 35V FB IN C1 C3 OUT SW R3 1M CS GND R4 72K LX1742CDU R2 1K FIGURE 19 – LX7142 WITH OUTPUT DISCONNECT (2N3906) 70% 69% 68% Efficiency 67% 66% 65% 64% 63% 62% 61% 60% 0 2 4 6 8 10 12 14 Output Current FIGURE 20 – EFFICIENCY VS. OUTPUT CURRENT (mA) Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 13 LX1741/LX1742 BOOST CONVERTER APPLICATION NOTE References Microsemi (2000). LX1741: High efficiency, high voltage boost controller. [Data Sheet], Garden Grove, CA. Author Microsemi (2000). LX1742: High efficiency, high voltage boost controller. [Data Sheet], Garden Grove, CA. Author Appendix A brief summary of the various capacitor types is provided below for the novice designer: CERAMIC: Multi-layer ceramic capacitors are intended for applications that require a device with a small physical size yet comparatively large electrical capacitance and high insulation resistance. The general-purpose ceramic capacitors, (while not intended for precision applications) are suitable for use as bypass and filtering applications in high frequency circuits where significant changes in capacitance, induced by temperature variation, can be tolerated. TANTALUM: There are three fundamental types of tantalum capacitors (tantalum foil, wet sintered anode, and solid electrolyte). The designer usually selects tantalum foil capacitors when high voltage components are required or when a substantial reverse voltage is applied to the capacitor (e.g., as in switched mode DC-DC conversion circuits). Wet sintered anode capacitors are often used when low DC leakage is required. Finally, solid electrolyte tantalum capacitors are preferred for their small size versus a given unit of capacitance. ALUMINUM ELECTROLYTIC: Aluminum electrolytic capacitors are typically preferred for signal filtering and bypass applications when large capacitance values are required and limited board space is available. FILM: Film capacitors are separated into either film/foil capacitor and metal-film capacitor categories. The film/foil capacitor is characterized by having a high insulation resistance and both excellent current carrying and pulse handling capability. Moreover, these device types are known to provide superior capacitance stability. The metalfilm capacitor features high volume efficiency and self-healing properties. Copyright 2002 Rev. 1.0, 2002-12-03 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 14