VF160/161E X O VF160–E/VF161–E 10KH ECL/PECL Compatible Enable/Disable Clock Oscillator Enable/Disable Output • Industrial Temperature Range • In–house “Inverted Mesa” Crystal Technology for Higher Frequencies • Wide Frequency Range • Very Low Phase Jitter • Electrical VALPEYFISHER VF161-E 200MHZ BO1H 0.497" (12,62mm) Absolute Max. Ratings F E AT U R E S Parameter Symb 0.250" (6,35mm) ø0.0180" (0,460mm) #8 0.100" (2,54mm) 0.600" (15,24mm) All dimensions are typical unless otherwise specified. Environmental and Mechanical #9 Creating a Part Number LEAD CONFIGURATION FREQUENCY STABILITY Code Specification S A B ±20 ±25 ±50 ±100 ppm ppm ppm ppm (std.) Specification HH ±2.5% ±5% INPUT VOLTAGE Code Specification L 3.3 Volt ±5% 5.0 Volt ±5% (std.) Code Specification G Gull Wing Through Hole (std.) OUTPUT DUTY CYCLE Code FREQ. E Electrical Connections VF160/161 Code Specification C Complementary Single output (std.) –40 +85 °C F 10 300 MHz Frequency Stability ∆F/F Overall Conditions Including: Calibration, temp., aging 10 yrs. shock, vibration ±100 ppm 1 Input Voltage Vcc Vcc Vee PECL LVPECL ECL 5.25 3.45 –5.45 V VF161E VF161L–E VF160E 80 mA Input Current Icc/Iee Specification 1 0°C to +70°C (std.) -40°C to +85°C 4.75 3.15 –4.95 5.00 3.30 –5.20 50 Ohm Load 50 Ohm to Vcc–2V or Thevenin Equiv. Bias required @50% Rise/Fall Time Tr/Tf 20% to 80% Logic “1” Level Voh @Vcc = 5.0V @Vee = –5.2V @Vcc = 3.3V Logic “0” Level Vol @Vcc = 5.0V @Vee = –5.2V @Vcc = 3.3V 45 50 55 % 1.5 ns 4.04 –0.96 2.59 4.19 –0.81 2.74 V PECL ECL LVPECL 3.15 –1.85 1.45 3.25 –1.65 1.55 V PECL ECL LVPECL 10 ms 1 ps Ts 2 1σ Control input “Vee” or floating Control input “High” 2 fj>1KHz – Enable – Disable Low Operating Temperature Range 0°C to +70°C (–40°C to +85°C available) Mechanical Shock Per MIL–STD–202, Method 213, Cond. E Thermal Shock Per MIL–STD–883, Method 1011, Cond. A Vibration Per MIL–STD–883, Method 2007, Cond. A Soldering Conditions 260°C, for 10s, Max. Hermetic Seal Leak rate less than 5 x 10–8 atm.cc/s of helium Pin Out Pin Pin Pin Pin Pin #1–Enable/Disable Control #7–Ground, Case (PECL)/Vee (ECL) #8–Output #9–Optional – Complementary output #14–Vcc (PECL)/Ground, Case (ECL) Notes: 1. Standard frequency stability (±20, ±25, ±50, others available). 2. Tighter duty cycles available. Measure @ 50% of the voltage swing. 3. Pin #9 omitted if complementary output is not specified. OPERATIONAL TEMP. RANGE Code V Ts Enable/ Disable Function #14 7.0 Note Frequency Range Phase Jitter 0.300" (7,62mm) Unit Storage Temp. Start–up Time #7 Max –0.5 GLASS STANDOFFS #1 Typ Vcc–Vee Duty Cycle 0.187" (4,75mm) Min Input Break Down Voltage Load 0.800" (20,32mm) Condition All specifications are subject to change without notice. Example: VF161SHHL-1CE-200MHz: Frequency Stability ±20ppm, Duty Cycle ±2.5%, Input Voltage 3.3 Volt ±5%, Operating Temperature -40°C to +85°C, Complementary Output, Enable/Disable, Frequency 200.000MHz. 75 South Street, Hopkinton, MA 01748 800-982-5737 508-435-6831 Fax: 508-435-5289 www.valpeyfisher.com 57