VFJA432 Quad Input to 200MHz Jitter Attenuator w/ FOUT to 200MHz RoHS Status Features 10MHz to 200MHz Output Frequency Range 8KHz to 200MHz Input Frequency Range Ultra Low Jitter and Phase Noise: -143 dBc/Hz @ 1KHz Low Power: < 150mW typical Compliant with Telcordia GR-253-CORE, GR-1244-CORE, ITU-T G.813, and ITU-T G.8261 Applications SONET / SDH / ATM Carrier Ethernet Synchronizers Wireless Infrastructure Description The VFJA432 is a Jitter Attenuator capable of providing an output frequency up to 200MHz. Two select inputs [S1,S0] allow the user to select 1 of 4 preset input frequencies. A Lock Detect signal indicates when the output signal is frequency locked to the input. Operating with a +3.3 volt power supply the device typically consumes less than 150mW. The VFJA432 is configured with two LVCMOS output ports. The device is available in a 19.5mm x 15.5mm surface mount package. LD Filter Fout 1 F in R-Divider VCXO PFD Fout 2 S0 S1 uController N- Divider Block Diagram 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-435-5289 • www.valpeyfisher.com • RevF1010 1 VFJA432 Quad Input to 200MHz Jitter Attenuator w/ FOUT to 200MHz Absolute Maximum Ratings Parameter Supply Break Down Voltage Storage Temperature Symbol Condition Min Typ Max Unit Vcc -0.5 5.5 V Ts -55 +105 C Note Electrical Specifications Parameter Output Frequency Range Input Frequency Range Input Level Output Level Logic “1” Output Level Logic “0” Phase Jitter SSB Phase Noise APR Modulation BW Duty Cycle Rise / Fall Time Start up time Supply Voltage Input Current Operating Temperature Range Lock Detect Symbol Condition Min Typ Max Unit Fout 10 200 MHz Fin 0.008 200 MHz 0.4 3.3 V p-p Vcc-0.1 Vcc V 0.0 .1 V 0.35 ps(rms) Vin AC coupled internally Voh Note 10K Ω // 10 pF Vol 12KHz to 20MHz 0.18 100Hz 1KHz 10KHz 100KHz -120 -143 -153 -163 Фn Tr/Tf 32 ppm 10 Hz @ 50% 45 20% to 80% .8 50 2 Vcc 3.15 Icc LD 3.30 45 Ta dBc/Hz -40 55 % 4.0 ns 10 ms 3.45 V 55 mA +85 C Output HIGH (> 2.5 V) : In Lock; Output LOW (< .5V): Out of Lock @ 25 MHz Note 1 LVCMOS Notes: 1. Consult factory for Bandwidth options 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-435-5289 • www.valpeyfisher.com • RevF1010 2 VFJA432 Quad Input to 200MHz Jitter Attenuator w/ FOUT to 200MHz Environmental and Mechanical Parameter Mechanical Shock Thermal Shock Specification Per MIL-STD-202, Method 213, Condition E Per MIL-STD-883, Method 1011, Condition A Vibration Per MIL-STD-883, Method 2007, Condition A Soldering Conditions 260C for 10s max Hermetic Seal -8 Leak rate less than 5x10 atm.cc/s of helium (crystal only) Pin Assignments Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Symbol Fin LD Vccp Vcc S1 DNC S0 Gnd n/c n/c Fout 1 Fout 2 n/c Gnd Description Input Frequency Lock Detect Connect to Vcc pin #4 3.3 Volt Power Supply Input Select (msb) Do not connect Input Select (lsb) Ground No connection No connection Output Frequency Output Frequency No connection Ground Notes Add .1 uF Capacitor How to Order VFJA432 Suffix Once Input and Output frequencies have been submitted and approved, the Factory will assign a part number. Table 2 P/N suffix -001 -003 S1:S0 00 01 10 11 00 01 10 11 Input Frequency (MHz) .008 19.44 25 125 10 10 10 10 Output Frequency (MHz) 25.00 25.00 25.00 25.00 16 16 16 16 P/N suffix -002 -004 S1:S0 00 01 10 11 00 01 10 11 Input Frequency (MHz) .008 19.44 25 125 1 2 5 10 Output Frequency (MHz) 125.00 125.00 125.00 125.00 10.00 10.00 10.00 10.00 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-435-5289 • www.valpeyfisher.com • RevF1010 3 VFJA432 Quad Input to 200MHz Jitter Attenuator w/ FOUT to 200MHz Mechanical Outline Connection Diagram LD Vcc = 3.3V C1 .01 uF 3 4 2 10 Fin 1 12 S1 S0 5 7 11 Fout 1 Fout 2 8 14 Gnd Recommended Pad Layout 75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-435-5289 • www.valpeyfisher.com • RevF1010 4