Future Technology Devices International Ltd TTL-232R TTL to USB Serial Converter Range of Cables Datasheet Document Reference No.: FT_000054 Version 2.03 Issue Date: 2016-05-23 Future Technology Devices International Limited (FTDI) Unit 1, 2 Seaward Place, Glasgow G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © Future Technology Devices International Limited Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 1 Description The TTL-232R cables are a family of USB to TTL serial UART converter cables incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB. Each TTL-232R cable contains a small internal electronic circuit board, utilising the FT232R, which is encapsulated into the USB connector end of the cable. The FT232R datasheet, DS_FT232R, is available at http://www.ftdichip.com. The other end of the cable comes with a selection of different connectors supporting various applications – see Table 1.1 Cables are FCC, CE, RoHS compliant and are available at TTL levels of +5V and +3.3V. Cables are available with either a 6-way SIL,0.1” pitch connector, a 3.5mm Audio Jack, an 8 way, keyed 2mm pitch connector (intended for use with VMUSIC2 or VDRIVE2) or bare, tinned wire ended connections (see Table 1.1) The USB side of the cable is USB powered and USB 2.0 full speed compatible. Each cable is 1.8m long and supports a data transfer rate up to 3 Mbaud. Each cable supports the FTDIChip-ID™, with a unique USB serial number programmed into the FT232R. This feature can be used to create a security or password protected file transfer access using the cable. Further information and examples on this feature are available at http://www.ftdichip.com under FTDIChip-ID Projects. The TTL-232R cables require USB drivers, available free from http://www.ftdichip.com, which are used to make the FT232R in the cable appear as a virtual COM port (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT232R on the cable though a DLL. This is illustrated in the Figure 1.1 Various Connector Options VCP TTY Wire Ended TTL-232R 3mm Audio Jack 6 way, 0.1" Single In Line connector USB Virtual COM Port 8 way, Keyed,2mm, Single In Line connector Various Connector Options Wire Ended D2XX DLL TTY 3mm Audio Jack USB 6 way, 0.1" Single In Line connector 8 way, Keyed,2mm, Single In Line connector Software application access to USB via D2XX Figure 1.1 Using the TTL-232R Cable Copyright © Future Technology Devices International Limited 1 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 1.1 Available Cables and Part Numbers The following Table 1.1 gives details of the available TTL-232R cables. Part Number Description ** TTL-232R-5V TTL-232R-3V3 USB to UART cable with +5V TTL level UART signals. USB to UART cable with +3.3V TTL level UART signals. End Connector* Cable details 6 core, UL2464 6 pin SIL, 0.1” pitch 24 AWG, diam=5mm 6 core, UL2464 6 pin SIL, 0.1” pitch 24 AWG, diam=5mm TTL-232R-5V- USB to UART cable with +5V TTL level Wire Ended (no WE** UART signals. connector) TTL-232R-3V3- USB to UART cable with +3.3V TTL level Wire Ended (no WE UART signals. connector) TTL-232R-5V- USB to UART cable with +5V TTL level AJ** UART signals. 6 core, UL2464 24 AWG, diam=5mm 6 core, UL2464 24 AWG, diam=5mm 2 core and spiral, 3.5mm Audio Jack 24 AWG diam=5mm 2 core and spiral, TTL-232R-3V3- USB to UART cable with +3.3V TTL level AJ UART signals. 3.5mm Audio Jack 24 AWG diam=5mm 8 way, keyed, 2mm TTL-232R-3V3- USB to UART cable with +3.3V TTL level connector for use 2mm UART signals. with FTDI VDRIVE2 or VMUSIC2 modules 7 core, UL2464 26 AWG, diam=5mm Table 1.1 TTL-232R Cables Descriptions and Part Numbers * FTDI supports customised end connector designs. For more information, please contact FTDI Sales Team ([email protected]) ** These cables are identical to cables which do not have the “5V” in the part number. The 5V was added to the part number for clarity. Copyright © Future Technology Devices International Limited 2 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 1.2 Certifications FTDI TTL-232R range of cables are fully RoHs compliant as well as CE and FCC certified (with the exception of the TTL-232R-XX-WE cables which have not yet completed FCC and CE testing). 1.3 USB Compliant The TTL-232R cables are fully compliant with the USB 2.0 specification. Copyright © Future Technology Devices International Limited 3 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Table of Contents 1 Description ..................................................................................... 1 1.1 Available Cables and Part Numbers ............................................................... 2 1.2 Certifications ................................................................................................. 3 1.3 USB Compliant .............................................................................................. 3 The TTL-232R cables are fully compliant with the USB 2.0 specification. ................ 3 2 Typical Applications ........................................................................ 6 2.1 Driver Support .............................................................................................. 6 2.2 Features ........................................................................................................ 7 3 Features of FT232R applicable toTTL-232R Cables ......................... 8 4 TTL-232R-5V and TTL-232R-3V3 Cables ....................................... 10 5 4.1 TTL-232R-5V, TTL-232R-3V3 Connector Pin Out and Mechanical details .... 10 4.2 TTL-232R-5V and TTL-232R-3V3 Cable Signal Descriptions ........................ 10 4.3 TTL-232R-5V and TTL-232R-3V3 Electrical Parameters ............................... 11 4.3.1 TTL-232R-5V Electrical Parameters ............................................................ 11 4.3.2 TTL-232R-3V3 Electrical Parameters .......................................................... 11 TTL-232R-5V-AJ and TTL-232R-3V3-AJ ........................................ 13 5.1 TTL-232R-5V-AJ, TTL-232R-3V3-AJ Connector Pin Out and Mechanical details ................................................................................................................... 13 6 7 5.2 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Cable Signal Descriptions .............. 14 5.3 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Electrical Parameters ..................... 14 5.3.1 TTL-232R-5V-AJ Electrical Parameters ........................................................ 14 5.3.2 TTL-232R-3V3-AJ Electrical Parameters ...................................................... 15 TTL-232R-5V-WE and TTL-232R-3V3-WE Cables .......................... 16 6.1 TTL-232R-5V-WE, TTL-232R-3V3-WE Connections and Mechanical Details 16 6.2 TTL-232R-5V-WE and TTL-232R-3V3-WE Cable Signal Descriptions ............ 16 6.3 TTL-232R-5V-WE and TTL-232R-3V3-WE Electrical Parameters .................. 16 6.3.1 TTL-232R-5V-WE Electrical Parameters ...................................................... 17 6.3.2 TTL-232R-3V3-WE Electrical Parameters .................................................... 17 TTL-232R-3V3-2mm Cables .......................................................... 18 7.1 TTL-232R-3V3-2mm Connector Pin Out and Mechanical details .................. 18 7.2 TTL-232R-3V3-2mm Cable Signal Descriptions ........................................... 19 7.3 TTL-232R-3V3-2mm Electrical Parameters .................................................. 19 8 Cable PCB Circuit Schematic ......................................................... 20 9 Contact Information ..................................................................... 21 Appendix A - Cable EEPROM Configuration ......................................... 22 Appendix B - List of Figures and Tables.............................................. 24 Copyright © Future Technology Devices International Limited 4 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Appendix C - Revision History ............................................................ 25 Copyright © Future Technology Devices International Limited 5 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 2 Typical Applications USB to Serial TTL Level Converter Upgrading Legacy Peripherals to USB Interface Microcontroller UART or I/O to USB Interface FPGA / PLD to USB Interface to FTDI VDRIVE2 or VMUSIC2 modules. Replace MAX232 type level shifters allowing for direct connection of products to PC via USB USB Instrumentation PC interface USB Industrial Control USB Software / Hardware Encryption Dongles 2.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) Windows 10 32,64-bit Windows 10 32,64-bit Windows 8/8.1 32,64-bit Windows 8/8.1 32,64-bit Windows 7 32,64-bit Windows 7 32,64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows XP and XP 64-bit Windows XP and XP 64-bit Windows 98, 98SE, ME, 2000, Server 2003, XP, Server 2008 and server 2012 R2 Windows 98, 98SE, ME, 2000, Server 2003, XP, Server 2008 and server 2012 R2 Windows XP Embedded Windows XP Embedded Windows CE 4.2, 5.0 and 6.0 Windows CE 4.2, 5.0 and 6.0 Mac OS 8/9, OS-X Linux 2.4 and greater Linux 2.4 and greater Android (J2xx) The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - see www.ftdichip.com for details. Copyright © Future Technology Devices International Limited 6 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 2.2 Features TTL-232R Converter Cable provides a USB to TTL Serial interface with various end connectors. Support for FT232R FTDIChip-ID™ feature for improved security. On board FT232RQ provides single chip USB to asynchronous serial data transfer interface. +5V or +3.3V output allows external logic to be powered from the USB port. Entire USB protocol handled by the electronics in the cable USB. 6 way outputs provide Tx, Rx, RTS#, CTS#, VCC and GND (except Audio Jack which provides only TX,RX and GND). Connect directly to a microcontroller UART or I/O pins. 8 way, keyed connector to support FTDI VDRIVE2 and VMUSIC2. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity. 3 way Audio Jack connector provides Tx, Rx and GND. Fully assisted hardware (RTS#/CTS#) or X-On / X-Off software handshaking. Low USB bandwidth consumption. UHCI / OHCI / EHCI host controller compatible. Data transfer rates from 300 baud to 3 Mbaud at TTL levels. USB 2.0 Full Speed compatible. -40°C to +85°C operating temperature range. Internal EEPROM with user writeable area. Cable length is 1.80m (6 feet). 5V CMOS drive outputs and 5V safe TTL inputs makes the TTL-232R easy to interface to 5V MCU’s. FCC and CE compliant. Custom versions also available (subject to MOQ). FTDI’s royalty-free VCP allow for communication as a standard emulated COM port and D2XX ‘direct’ drivers provide DLL application programming interface. Copyright © Future Technology Devices International Limited 7 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 3 Features of FT232R applicable toTTL-232R Cables The TTL-232R cables use FTDI’s FT232RQ USB to serial IC device. This section summarises the key features of the FT232RQ which apply to the TTL-232R USB to serial TTL converter cables. For further details, and a full features and enhancements description consult the FT232R datasheet, this is available from www.ftdichip.com. Internal EEPROM. The internal EEPROM in each cable is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors. Each cable is supplied with the internal EEPROM pre-programmed as described in Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 1103, No.666 West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright © Future Technology Devices International Limited 8 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Appendix A - Cable EEPROM Configuration. A user area of the internal EEPROM is available to system designers to allow storing additional data. The internal EEPROM descriptors can be programmed in circuit, over USB without any additional voltage requirement. It can be programmed using the FTDI utility software called FT_PROG, which can be downloaded from FTDI Utilities on the FTDI website (www.ftdichip.com). Lower Operating and Suspend Current. The FT232R has a low 15mA operating supply current and a very low USB suspend current of approximately 70μA. (Note that during suspend mode, the current drawn by application should not exceed 2.5mA to remain USB compliant) Low USB Bandwidth Consumption. The USB interface of the FT232R, and therefore the TTL-232R cables has been designed to use as little as possible of the total USB bandwidth available from the USB host controller. High Output Drive Option. The UART interface I/O pins on the TTL-232R cables (RXD, TXD, RTS#, and CTS#) can be configured to use the FT232R’s high output drive option. This option allows the FT232R I/O pins to drive up to three times the standard signal drive level. This allows multiple devices to be driven, or devices that require a greater signal drive strength to be interfaced to the cables. This option is enabled in the internal EEPROM. UART Pin Signal Inversion. The sense of each of the eight UART signals can be individually inverted by configuring options in the internal EEPROM. For example CTS# (active low) can be changed to CTS (active high), or TXD can be changed to TXD#. FTDIChip-ID™. The FT232R includes the new FTDIChip-ID™ security dongle feature. This FTDIChip-ID™ feature allows a unique number to be burnt into each cable during manufacture. This number cannot be reprogrammed. This number is only readable over USB can be used to form the basis of a security dongle which can be used to protect any customer application software being copied. This allows the possibility of using the TTL-232R cables as a dongle for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-ID™ number when encrypted with other information. This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-ID™ to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note, AN232R-02, available from FTDI website (www.ftdichip.com) describes this feature. Improved EMI Performance. The TTL-232R cables are FCC and CE certified. Extended Operating Temperature Range - The TTL-232R cables are capable of operating over an extended temperature range of -40º to +85º C thus allowing them to be used in automotive or industrial applications. Copyright © Future Technology Devices International Limited 9 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 4 TTL-232R-5V and TTL-232R-3V3 Cables The TTL-232R-5V and TTL-232R-3V3 cables are both terminated by a 6 way, 0.1”, Single-In-Line (SIL) connector. The difference between the two cables is that the TTL-232R-5V operates at +5V levels (signals and power supply) and the TTL-232R-3V3 operates at +3.3V levels (signals only, VCC= +5V). 4.1 TTL-232R-5V, TTL-232R-3V3 Connector Pin Out and Mechanical details 6 pin header 0.1in pitch VCC GND 1 1 CTS# 2 2 VCC 3 TXD BLACK BROWN 3 RED 4 4 ORANGE RXD 5 5 RTS# 6 6 CABLE 1.8m YELLOW GREEN Figure 4.1 TTL-232R-5V and TTL-232R-3V3, 6 Way Header Pin Out The mechanical details of the 6 way connector are shown in the following diagram Dimensions (mm) A Pin 1 B C E A 2.54 +/- 0.05 B 12.70 +/- 0.2 C D 15.24 +/- 0.2 D 14.0 +/- 0.2 E 2.54 +/- 0.05 Figure 4.2 TTL-232R-5V TTL-232R-3V3, 6 Way Header Mechanical Details 4.2 TTL-232R-5V and TTL-232R-3V3 Cable Signal Descriptions Header Pin Name Type Colour Description 1 GND GND Black Device ground supply pin. 2 CTS# Input Brown Clear to Send Control input / Handshake signal. 3 VCC Output Red Number +5V output, Copyright © Future Technology Devices International Limited 10 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Header Pin Name Type Colour Description 4 TXD Output Orange Transmit Asynchronous Data output. 5 RXD Input Yellow Receive Asynchronous Data input. 6 RTS# Output Green Request To Send Control Output / Handshake signal. Number Table 4.1 TTL-232R-5V and TTL-232R-3V3 Cable Signal Descriptions 4.3 TTL-232R-5V and TTL-232R-3V3 Electrical Parameters 4.3.1 TTL-232R-5V Electrical Parameters Parameter Description Minimum Typical Maximum Units Conditions Dependant on the USB VCC Output Power Voltage 4.25 5.0 5.25 V port that the TTL-232R5V is connected to IO T Output Power Current Operating Temperature Range - - 75 mA -40 - +85 Minimum Typical Maximum Units Must be less that 2.5mA during suspend. o C Table 4.2 TTL-232R-5V I/O Operating Parameters Parameter Description Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 2mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Maximum Units Table 4.3 TTL-232R-5V I/O Pin Characteristics 4.3.2 TTL-232R-3V3 Electrical Parameters Parameter Description Minimum Typical Conditions Dependant on the USB VCC Output Power Voltage 4.25 5.0 5.25 V port that the TTL-232R3V3 is connected to IO T Output Power Current Operating Temperature Range - - 75 -40 - +85 mA Must be less that 2.5mA during suspend. o C Table 4.4 TTL-232R-3V3 I/O Operating Parameters Copyright © Future Technology Devices International Limited 11 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 4.5 TTL-232R-3V3 I/O Pin Characteristics Copyright © Future Technology Devices International Limited 12 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 5 TTL-232R-5V-AJ and TTL-232R-3V3-AJ The TTL-232R-5V-AJ and TTL-232R-3V3-AJ cables are both terminated by a standard 3.5mm Audio Jack (AJ) connector. The difference between the two cables is that the TTL-232R-5V-AJ operates at +5V levels (signals and power supply) and the TTL-232R-3V3-AJ operates at +3.3V levels (signals and power supply). On these cables the VCC power is not transferred. 5.1 TTL-232R-5V-AJ, TTL-232R-3V3-AJ Connector Pin Out and Mechanical details GND 1 BLACK CABLE 1.8m ORANGE TXD 4 RXD 5 YELLOW 3.5mm Audio Jack Figure 5.1 TTL-232R-5V and TTL-232R-3V3, 6 Way Header Pin Out The mechanical details of the Audio Jack connector are shown in the following Figure 5.2. 3.0+/- 0.1 3.2+/- 0.1 2.6+/- 0.1 6.0+/- 0.1 3.5+/- 0.1 14.0 +/- 0.2 Dimensions in mm Figure 5.2 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Audio Jack Mechanical Details Copyright © Future Technology Devices International Limited 13 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 5.2 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Cable Signal Descriptions Header Pin Name Type Colour Description TIP TXD GND Black Transmit Asynchronous Data output. RING RXD Input Brown Receive Asynchronous Data input. SLEEVE GND Output Red Number GND Table 5.1 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Cable Signal Descriptions 5.3 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Electrical Parameters 5.3.1 TTL-232R-5V-AJ Electrical Parameters Parameter IO T Description Minimum Output Power Current Operating Temperature Range Typical Maximum Units - 75 mA -40 +85 Conditions Must be less that 2.5mA during suspend. o C Table 5.2 TTL-232R-5V-AJ I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 6mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 6mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 5.3 TTL-232R-5V-AJ I/O Pin Characteristics Copyright © Future Technology Devices International Limited 14 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 5.3.2 TTL-232R-3V3-AJ Electrical Parameters Parameter IO T Description Minimum Output Power Current Operating Temperature Range Typical Maximum Units - 75 mA -40 +85 Conditions Must be less that 2.5mA during suspend. o C Table 5.4 TTL-232R-3V3-AJ I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 5.5 TTL-232R-3V3-AJ I/O Pin Characteristics Copyright © Future Technology Devices International Limited 15 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 6 TTL-232R-5V-WE and TTL-232R-3V3-WE Cables The TTL-232R-5V-WE and TTL-232R-3V3-WE cables are both un-terminated; they are bare and tinned wires. The difference between the two cables is that the TTL-232R-5V-WE operates at +5V levels (signals and power supply) and the TTL-232R-3V3-WE operates at +3.3V levels (signals only, VCC=+5V). 6.1 TTL-232R-5V-WE, TTL-232R-3V3-WE Connections and Mechanical Details The following Figure 6.1 shows the cable signals and the wire colours for these signals on the TTL-232R5V-WE and TTL-232R-3V3-WE cables. VCC GND 1 1 BLACK CTS# 2 2 BROWN VCC 3 TXD 3 RED 4 4 ORANGE RXD 5 5 YELLOW RTS# 6 6 GREEN CABLE 1.8m Figure 6.1 TTL-232R-5V-WE and TTL-232R-3V3-WE Connections Figure 6.2 TTL-232R-5V-WE and TTL-232R-3V3-WE Mechanical Details (dimensions in mm) 6.2 TTL-232R-5V-WE and TTL-232R-3V3-WE Cable Signal Descriptions Colour Name Type Description Black GND GND Device ground supply pin. Brown CTS# Input Clear to Send Control input / Handshake signal. Red VCC Output +5V output Orange TXD Output Transmit Asynchronous Data output. Yellow RXD Input Green RTS# Output Receive Asynchronous Data input. Request To Send Control Output / Handshake signal. Table 6.1 TTL-232R-5V-WE and TTL-232R-3V3-WE Cable Signal Descriptions 6.3 TTL-232R-5V-WE and TTL-232R-3V3-WE Electrical Parameters Copyright © Future Technology Devices International Limited 16 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 6.3.1 TTL-232R-5V-WE Electrical Parameters Parameter Description Minimum Typical Maximum Units Conditions Dependant on the USB port VCC Output Power Voltage 4.25 5.0 5.25 V that the TTL-232R-5V-WE is connected to IO T Output Power Current Operating Temperature Range - 75 -40 +85 mA Must be less that 2.5mA during suspend. o C Table 6.2 TTL-232R-5V-WE I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 6mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 6mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 6.3 TTL-232R-5V-WE I/O Pin Characteristics 6.3.2 TTL-232R-3V3-WE Electrical Parameters Parameter Description Minimum Typical Maximum Units Conditions Dependant on the USB port VCC Output Power Voltage 4.25 5.0 5.25 V that the TTL-232R-3V3-WE is connected to IO T Output Power Current Operating Temperature Range - 75 -40 +85 mA Must be less that 2.5mA during suspend. o C Table 6.4 TTL-232R-3V3-WE I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 6.5 TTL-232R-3V3-WE I/O Pin Characteristics Copyright © Future Technology Devices International Limited 17 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 7 TTL-232R-3V3-2mm Cables The TTL-232R-3V3-2mm cable is terminated by a 8 way, 2mm pitch, Single-In-Line (SIL) keyed connector. The TTL-232R-3V3-2mm operates at +3.3V levels (signals and power supply). These cables are primarily intended for interfacing the FTDI VDRIVE2 and VMUSIC2 modules. Note that when connected to VDRIVE2 or VMUSIC2 module, the TTL-232R-3V3-2mm cable 8-way connector pin 1 connects to pin 8 of the module, and pin 8 of the cable connects to pin 1 of the cable. 7.1 TTL-232R-3V3-2mm Connector Pin Out and Mechanical details 8 pin header 2mm pitch VCC GND 1 8 CTS# 7 VCC 6 TXD 5,1 RXD 4 RTS# 3 BLUE 2 CABLE 1.8m KEY 3 4 5 GREEN YELLOW ORANGE 6 RED 7 BROWN 8 BLACK Figure 7.1 TTL-232R-3V3-2mm, 8 Way Header Pin Out The mechanical details of the 2mm pitch 8 way, keyed, connector are shown in the following diagram Dimensions (mm) Pin 1 B C A A 2.00 +/- 0.005 B 14.00 +/- 0.2 E C 16.40 +/- 0.2 D 7.10 +/- 0.25 E 2.00 +/- 0.005 D Figure 7.2 TTL-232R-3V3-2mm, 2mm pitch, Keyed, 8 way Header Mechanical Details Copyright © Future Technology Devices International Limited 18 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 7.2 TTL-232R-3V3-2mm Cable Signal Descriptions Header Pin Number Name Type Colour Description Ring Indicator Control Input. When remote wake up is 1 RI# Output Blue enabled taking RI# low (20ms active low pulse) can be used to resume the VMUSIC2 or VDRIVE2 host controller from suspend. Connected to TXD. This connection is keyed to connect to the VRDIVE2 or the 2 KEY KEY KEY 3 RTS# Output Green Request To Send Control Output / Handshake signal. 4 RXD Input Yellow Receive Asynchronous Data input. 5 TXD Output Orange Transmit Asynchronous Data output. 6 VCC Output Red 7 CTS# Input Brown Clear to Send Control input / Handshake signal. 8 GND GND Black Device ground supply pin. VMUSIC2 modules +5V output, Table 7.1 TTL-232R-3V3-2mm Cable Signal Descriptions 7.3 TTL-232R-3V3-2mm Electrical Parameters Parameter Description Minimum Typical Maximum Units 4.25 5.0 5.25 V Conditions Dependant on the USB port VCC Output Power Voltage that the TTL-232R-3V3-2mm is connected to IO T Output Power Current Operating Temperature Range - 75 -40 +85 mA Must be less that 2.5mA during suspend. o C Table 7.2 TTL-232R-3V3-2mm I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 7.3 TTL-232R-3V3-2mm I/O Pin Characteristics Copyright © Future Technology Devices International Limited 19 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 8 Cable PCB Circuit Schematic The circuit schematic for the small internal electronic circuit board, utilising the FTDI FT232R, which is encapsulated into the USB connector end of the cable, is shown in Figure 8.1. Customised versions of these cables are also available. Users interested in customised versions of these cables should contact FTDI sales ([email protected]). VCC-IO PULL UP RESISTORS NOT FITTED CTS# TXD RXD 1 2 3 4 VCC-IO VCC-3V3 VCC RTS# INTERNAL IO VOLTAGE SELECTION USB “A” PLUG 5 GND FB 10nF 4.7uF + USB-DM USB-DP 47pF x 2 100nF VCC VCCIO 1 18 15 14 4 19 17 FT232RQ 20 24 16 26 30 32 2 8 270R 270R TXD RTS# RXD CTS# VCC-3V3 100nF Figure 8.1 Circuit Schematic of PCB Used in the TTL to USB Serial Converter Cables Copyright © Future Technology Devices International Limited 20 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 9 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 1103, No.666 West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright © Future Technology Devices International Limited 21 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Appendix A - Cable EEPROM Configuration Each TTL-232R cable is controlled by the FTDI FT232R IC. This FT232R device contains an EEPROM which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in Table 0.1 Parameter Value USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6001h FTDI default PID (hex) Serial Number Enabled? Notes Yes A unique serial number is generated and programmed into Serial Number See Note the EEPROM during device final test. Enabling this option will make the device pull down on the Pull down I/O Pins in USB Suspend Manufacturer Name Disabled UART interface lines when the power is shut off (PWREN# is high). FTDI Product description depends on the cable. The following lists the Product description for each different cable. TTL-232R-5V TTL-232R-3V3 Product Description See note TTL-232R-5V-AJ TTL-232R-AJ-3V3 TTL-232R-5V-WE TTL-232R-3V3-WE TTL-232R-3V3-2mm = USB <-> Serial Cable Max Bus Power Current Power Source Device Type 90mA Bus Powered FT232R Returns USB 2.0 device description to the host. Note: The device is be a USB 2.0 Full Speed device USB Version 0200 (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s). Remote Wake Up Disabled High Current I/Os Enabled Load VCP Driver Enabled Invert TXD Disabled Signal on this pin becomes TXD# if enable. Invert RXD Disabled Signal on this pin becomes RXD# if enable. Invert RTS# Disabled Signal on this pin becomes RTS if enable. Invert CTS# Disabled Signal on this pin becomes CTS if enable. Enables the high drive level on the UART and CBUS I/O pins. Makes the device load the VCP driver interface for the device. Table 0.1 Default Internal EEPROM Configuration Copyright © Future Technology Devices International Limited 22 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 The internal EEPROM in the cable can be re-programmed over USB using the utility program FT_PROG. FT_PROG can be downloaded from the www.ftdichip.com. Version 2.8a or later is required for the FT232R chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © Future Technology Devices International Limited 23 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Appendix B - List of Figures and Tables List of Figures Figure 1.1 Using the TTL-232R Cable ............................................................................................................ 1 Figure 4.1 TTL-232R-5V and TTL-232R-3V3, 6 Way Header Pin Out ........................................................ 10 Figure 4.2 TTL-232R-5V TTL-232R-3V3, 6 Way Header Mechanical Details ............................................ 10 Figure 5.1 TTL-232R-5V and TTL-232R-3V3, 6 Way Header Pin Out ........................................................ 13 Figure 5.2 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Audio Jack Mechanical Details ............................... 13 Figure 6.1 TTL-232R-5V-WE and TTL-232R-3V3-WE Connections ........................................................... 16 Figure 6.2 TTL-232R-5V-WE and TTL-232R-3V3-WE Mechanical Details (dimensions in mm) ............. 16 Figure 7.1 TTL-232R-3V3-2mm, 8 Way Header Pin Out ............................................................................. 18 Figure 7.2 TTL-232R-3V3-2mm, 2mm pitch, Keyed, 8 way Header Mechanical Details ......................... 18 Figure 8.1 Circuit Schematic of PCB Used in the TTL to USB Serial Converter Cables ........................ 20 List of Tables Table 1.1 TTL-232R Cables Descriptions and Part Numbers ...................................................................... 2 Table 4.1 TTL-232R-5V and TTL-232R-3V3 Cable Signal Descriptions .................................................... 11 Table 4.2 TTL-232R-5V I/O Operating Parameters ...................................................................................... 11 Table 4.3 TTL-232R-5V I/O Pin Characteristics ........................................................................................... 11 Table 4.4 TTL-232R-3V3 I/O Operating Parameters .................................................................................... 11 Table 4.5 TTL-232R-3V3 I/O Pin Characteristics ......................................................................................... 12 Table 5.1 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Cable Signal Descriptions ........................................ 14 Table 5.2 TTL-232R-5V-AJ I/O Operating Parameters ................................................................................ 14 Table 5.3 TTL-232R-5V-AJ I/O Pin Characteristics ..................................................................................... 14 Table 5.4 TTL-232R-3V3-AJ I/O Operating Parameters .............................................................................. 15 Table 5.5 TTL-232R-3V3-AJ I/O Pin Characteristics ................................................................................... 15 Table 6.1 TTL-232R-5V-WE and TTL-232R-3V3-WE Cable Signal Descriptions ...................................... 16 Table 6.2 TTL-232R-5V-WE I/O Operating Parameters ............................................................................... 17 Table 6.3 TTL-232R-5V-WE I/O Pin Characteristics .................................................................................... 17 Table 6.4 TTL-232R-3V3-WE I/O Operating Parameters ............................................................................. 17 Table 6.5 TTL-232R-3V3-WE I/O Pin Characteristics .................................................................................. 17 Table 7.1 TTL-232R-3V3-2mm Cable Signal Descriptions ......................................................................... 19 Table 7.2 TTL-232R-3V3-2mm I/O Operating Parameters .......................................................................... 19 Table 7.3 TTL-232R-3V3-2mm I/O Pin Characteristics ............................................................................... 19 Table 0.1 Default Internal EEPROM Configuration ..................................................................................... 22 Copyright © Future Technology Devices International Limited 24 Document Reference No.: FT_000054 TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES Datasheet Version 2.03 Clearance No.: FTDI# 53 Appendix C - Revision History Document Title: TTL to USB Serial Converter Range of Cables Document Reference No.: FT_000054 Clearance No.: FTDI# 53 Driver Page: http://www.ftdichip.com/FTDrivers.htm Document Feedback: Send Feedback Revision 1.0 2.0 2.01 Changes Date Initial Release May 2006 Consolidated all TTL-232R variants into one datasheet. July 2008 Changed part numbers for +5V cables. Corrected Table 6.1, RED wire VCC description September 2008 Corrected Table 4.3, I source and I sink values Added section 1.3 USB Compliant Logo Updated contact details 2.02 September 2010 Replaced reference MProg with FT_Prog Updated driver list 2.1 2.03 Changed tolerance of wire length in 6.2 May 2016 Updated contact details and Append C format Copyright © Future Technology Devices International Limited 25