雙銅紙 A4 100P 雙面印 中間一刀裁 完成尺寸 148.5X210 出單請打上料號 CPT-3076-01 4 PSoC J umper Settings Jumper Thermal Management Expansion Board Kit CY8CKIT-036 Default Setting QuickQuick Start Guide SINGLE PWM_TMP I2C Temperature Sensor DUAL I2C/SMBus/PMBus Port J2 3-pin header to choose between single sensor or dual sensor (daisy chain) connection for the PWM 2x20 Pin Headers temperature sensors. Place jumper in 1-2 position to enable dual sensor daisy-chain mode. Diode Temperature Sensor 4-Wire Fan Socket 3.3V VDDIO 5V J3 PWM Temperature Sensor 3-pin header to set logic signal levels for digital temperature sensors. Place in 1-2 for 5V interfacing. Place in 2-3 position to 3.3V interfacing. 1-Wire Temperature Sensor 12V 12V_DVK 12V_EXT J9 1 Quick in the Guide Box? W hat’s 1 3-pin header for fan power supply. Place in 1-2 Power Jack 2 position to source external power from the power jack (J13). Place in 2-3 position to source 12V power from the DVK. 1 Cypress TME Board 2 Quick Start Guide 3 Power DC Adaptor 12V/2A 4 System CD NOTE: For support, please contact us at: 3 4 This kit requires one of the following kits to operate: Online:www.cypress.com/go/support 1.CY8CKIT-001 PSoC Development Kit Telephone (24x7): +1-800-541-4736 ext. 8 (USA) or +1-408-943-2600 ext. 8 (International) 2.CY8CKIT-030 PSoC 3 Development Kit For additional information visit: http://www.cypress.com/go/CY8CKIT-036 or http://tme.terasic.com http://tme.terasic.com http://www.cypress.com/go/CY8CKIT-036 CPT-3076-01 PSoC Thermal Management Expansion Board Kit 2 1 T ME module installation CY8CKIT-001 Insert the kit CD and install the kit software 2 • View the User’s Guide for detailed instructions • During the install, continue with hardware setup Set “VDD DIG” and “VDD ANLG” to 3.3V using SW3, J6 and J7 on the CY8CKIT-001 3 1 T ME module installation CY8CKIT-030 Insert the kit CD and install the kit software 2 • View the User’s Guide for detailed instructions • During the install, continue with hardware setup Set VDDD and VDDA to 3.3V by placing jumpers in 1-2 position of J10 and J11. Enable POT_PWR by installing a jumper on J30 of the CY8CKIT-030 J30 3 5 Ensure LCD Power jumper (J12) is set to ON and the LCD display is plugged into the DVK Program the PSoC Thermal Management Demo • Connect the Miniprog3 to the PSoC 3 processor module. • Using the PSoC Programmer software, program the PSoC device with the "Thermal_Demo-001_rev1.hex" file located at "C:\Program Files\Terasic\PSoC Thermal Management EBK\1.0\Firmware\Hex_Files". 4 6 Connect VR to P1_2, SW1 to P1_4 and SW2 to P1_5 on the breadboard area of the CY8CKIT-001 and ensure J11 is set with a jumper. 3 4 Remove the USB cable from the CY8CKIT-030 and plug the TME EBK into Port E 6 Run the PSoC Thermal Management Demo • Connect the USB cable to J1 on the CY8CKIT-030. • Using the PSoC Programmer software, program the PSoC device with the "Thermal_Demo-030_rev1.hex" file located at "C:\Program Files\Terasic\PSoC Thermal Management EBK\1.0\Firmware\Hex_Files". Run the PSoC Thermal Management Demo • Remove power to the DVK, plug the TME EBK into Port A of the DVK and re-apply power to the DVK and EBK using the provided power adapter(s) • Use SW1 to navigate between the thermal management screens on the LCD • Refer to the User’s Guide example 3 for project details and additional thermal management solutions Program the PSoC Thermal Management Demo CAUTION: DO NOT plug in TME board-follow instructions in Step 4 5 Select 12V_EXT with J9 in the 1-2 position on the TME EBK. Then plug in the 12V/2A power supply into the TME EBK at J13.Connect the USB cable to J1 on the CY8CKIT-030. • Use SW2 to navigate between the thermal management screens on the LCD • Refer to the User’s Guide example 3 for project details and additional thermal management solutions. CAUTION: DO NOT plug in TME board-follow instructions in Step 6 www.terasic.com